Commit Graph

177 Commits

Author SHA1 Message Date
Ricardo Ribalda Delgado 77c5a7f5c1 iio: adc: ad7476: Add support for TI ADS786X ADCs
Add support for Texas Instruments ADS7866, ADS7867 and ADS7868
8/10/12 bit Single channel ADC.

Datasheet: http://www.ti.com/lit/ds/symlink/ads7868.pdf

Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-02-09 18:46:02 +00:00
Artur Rojek 1a78daea10 IIO: add Ingenic JZ47xx ADC driver.
Add an IIO driver for the ADC hardware present on Ingenic JZ47xx SoCs.

Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-02-09 18:46:01 +00:00
Stefan Popa a5f8c7da3d iio: adc: Add AD7768-1 ADC basic support
The ad7768-1 is a single channel, precision 24-bit analog to digital
converter (ADC).

This basic patch configures the device in fast mode, with 32 kSPS and
leaves the default sinc5 filter.

Two data conversion modes are made available. When data is retrieved by
using the read_raw attribute, one shot single conversion mode is set.
The continuous conversion mode is enabled when the triggered buffer
mechanism is used. To assure correct data retrieval, the driver waits
for the interrupt triggered by the low to high transition of the DRDY
pin.

Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-02-02 10:28:56 +00:00
Tomer Maimon 9bf85fbc9d iio: adc: add NPCM ADC driver
Add Nuvoton NPCM BMC Analog-to-Digital Converter(ADC) driver.

The NPCM ADC is a 10-bit converter for eight channel inputs.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-01-19 18:58:54 +00:00
Dan Murphy e717f8c6df iio: adc: Add the TI ads124s08 ADC code
Introduce the TI ADS124S08 and the ADS124S06 ADC
devices from TI.  The ADS124S08 is the 12 channel ADC
and the ADS124S06 is the 6 channel ADC device

These devices share a common datasheet:
http://www.ti.com/lit/gpn/ads124s08

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-01-12 18:42:39 +00:00
Stefan Popa 2985a5d884 staging: iio: adc: ad7606: Move out of staging
Move ad7606 ADC driver out of staging and into the mainline.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-01-05 16:10:59 +00:00
Jonathan Bakker d1655c7f48 iio: adc: Allow selection of Exynos ADC on S5PV210
Make it possible to use Exynos ADC driver on S5PV210 based devices.

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-12-12 17:19:32 +00:00
Stefan Popa b3af341bbd iio: adc: Add ad7124 support
The ad7124-4 and ad7124-8 are a family of 4 and 8 channel sigma-delta ADCs
with 24-bit precision and reference.

Three power modes are available which in turn affect the output data rate:
 * Full power: 9.38 SPS to 19,200 SPS
 * Mid power: 2.34 SPS to 4800 SPS
 * Low power: 1.17 SPS to 2400 SPS

The ad7124-4 can be configured to have four differential inputs, while
ad7124-8 can have 8. Moreover, ad7124 also supports per channel
configuration. Each configuration consists of gain, reference source,
output data rate and bipolar/unipolar configuration.

Datasheets:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD7124-4.pdf
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/ad7124-8.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-11-17 16:41:09 +00:00
Charles-Antoine Couret 7f40e06143 iio:adc:ad7949: Add AD7949 ADC driver family
Compatible with AD7682 and AD7689 chips.
It is a Analog Devices ADC driver 14/16 bits 4/8 channels
with SPI protocol

Datasheet of the device:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7949.pdf

Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-11-03 09:44:34 +00:00
Marcus Folkesson 3a89b289df iio: adc: add support for mcp3911
MCP3911 is a dual channel Analog Front End (AFE) containing two
synchronous sampling delta-sigma Analog-to-Digital Converters (ADC).

Co-developed-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-19 20:02:48 +01:00
Siddartha Mohanadoss e13d757279 iio: adc: Add QCOM SPMI PMIC5 ADC driver
This patch adds support for QCOM SPMI PMIC5 family
of ADC driver that supports hardware based offset and
gain compensation. The ADC peripheral can measure both
voltage and current channels whose input signal is
connected to the PMIC ADC AMUX.

The register set and configuration has been refreshed
compared to the prior QCOM PMIC ADC family. Register
ADC5 as part of the IIO framework.

Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-08-18 18:11:43 +01:00
Freeman Liu 5df362a6cf iio: adc: Add Spreadtrum SC27XX PMICs ADC support
The Spreadtrum SC27XX PMICs ADC controller contains 32 channels,
which is used to sample voltages with 12 bits conversion.

[Baolin Wang did lots of improvements]

Signed-off-by: Freeman Liu <freeman.liu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-06-30 18:59:40 +01:00
Geert Uytterhoeven 5126aec542 iio: adc: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.

Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.

This simplifies the dependencies, and allows to improve compile-testing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-06-24 14:15:36 +01:00
Arnd Bergmann c2c8406b31 iio: adc: sun4i-gpadc: select REGMAP_IRQ
We can't call regmap_irq_get_virq() unless the regmap-irq support
is enabled:

drivers/iio/adc/sun4i-gpadc-iio.o: In function `sun4i_irq_init':
sun4i-gpadc-iio.c:(.text+0x59c): undefined reference to `regmap_irq_get_virq'

I came across this in a randconfig build now, but I guess this is
a much older problem that I simply never hit before because regmap_irq
is usually enabled by one of the other drivers that need it.

Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-06-10 11:52:28 +01:00
Greg Kroah-Hartman 9d569b1cf7 First round of IIO fixes for the 4.17 cycle.
* core
   - fix up some issues with overflow etc around wrong types
     for some fo the kfifo handling functions.  Seems unlikely
     this would be triggered in reality but the fixes are simple
     so let's tidy them up.  Second patch deals with checking
     the userspace value passed for length for potential overflow.
 * ad7793
   - Catch up with changes to the ad_sigma_delta core and use
     read_raw / write_raw iwth IIO_CHAN_INFO_SAMP_FEW to handle
     sampling frequency control.
 * at91-sama5d2
   - Channel config for differential channels was completely broken.
   - Missing Kconfig dependency for buffer support.
 * hid-sensor
   - Fix an issue with powering up after resume due to wrong reference
     counting.
 * stm32-dfsdm
   - Fix an issue with second writes of the oversampling settings
     failing.
   - Fix an issue with the sample rate being set to half of requested
     value when particular clock source is used.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlrwhdsRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0Fog75w//SWKY1QTUdP3fdcvMlF8K9/Lu++MM8XcN
 c90LjoWbWJz8Qne9va8+JIb00FdWC4xUDXSD3T73RUqxpj2L+PhuhByYgLHrkuNG
 vhF21gK+NFYkreNo7N8LyVVStLQn28upIDW39fcxPPZrxuhW5+7bJ6c2ovUJ4uqB
 Waljqj7sPxZQHDt9K+0WoRhsxvDVKKKqDYe3jvOqhK1Z7cylBtMct6Pa7vk6VDon
 LBPrObHNFcrkuC2eVVryBOff4y5nvi6sGHo9xeWyG6wLg5N7eXMWGnpvB56qLt+M
 ywT0U6EILvCbLaCFC7Qyinvcsn+W1udQi3zNbFNYI+nBvdMiOA14dEfb5IC2iH1g
 Nkinnc0HpPvZJPqTijS7ngQ89LiUZAdYPPEt2rodoNu5yZ4Vt/6rNvJasdJUMV78
 IEgn4Be1dfw9fIKJJXu7Jnp9Dr444sRxjgFNPByOobjtozN4ENgkfGyItBP7jsbJ
 oXzX+Pt90Jc6plw28zx+tGx76SB52HLgPwZgfRCjpH6lZ730keTA7d+e7DbBGf0A
 Bfm5DGD3NWBRfFWsr0ImGMEeST0ZwqbEWsnfPpEQxGZe9WvP60WPYVF0DgmQw1On
 CTgUR3QF7MtwddBL4NaluPgHJeuYHJAihy3KtIK+NSDNIUXgzdjqCQioaniLmzQx
 q1egq6KxqRU=
 =1bkD
 -----END PGP SIGNATURE-----

Merge tag 'iio-fixes-for-4.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First round of IIO fixes for the 4.17 cycle.

* core
  - fix up some issues with overflow etc around wrong types
    for some fo the kfifo handling functions.  Seems unlikely
    this would be triggered in reality but the fixes are simple
    so let's tidy them up.  Second patch deals with checking
    the userspace value passed for length for potential overflow.
* ad7793
  - Catch up with changes to the ad_sigma_delta core and use
    read_raw / write_raw iwth IIO_CHAN_INFO_SAMP_FEW to handle
    sampling frequency control.
* at91-sama5d2
  - Channel config for differential channels was completely broken.
  - Missing Kconfig dependency for buffer support.
* hid-sensor
  - Fix an issue with powering up after resume due to wrong reference
    counting.
* stm32-dfsdm
  - Fix an issue with second writes of the oversampling settings
    failing.
  - Fix an issue with the sample rate being set to half of requested
    value when particular clock source is used.
2018-05-09 17:08:29 +02:00
Eugen Hristev 76974ef9d1 iio: adc: select buffer for at91-sama5d2_adc
We need to select the buffer code, otherwise we get build errors
with undefined functions on the trigger and buffer,
if we select just IIO and then AT91_SAMA5D2_ADC from menuconfig

This adds a Kconfig 'select' statement like other ADC
drivers have it already.

Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-04-21 15:57:10 +01:00
Linus Torvalds 1b2951dd99 This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
 
 - Nintendo Wii GameCube GPIO, known as "Hollywood"
 
 - Raspberry Pi mailbox service GPIO expander
 
 - Spreadtrum main SC9860 SoC and IEC GPIO controllers.
 
 Improvements:
 
 - Implemented .get_multiple() callback for most of the
   high-performance industrial GPIO cards for the ISA bus.
 
 - ISA GPIO drivers now select the ISA_BUS_API instead of
   depending on it. This is merged with the same pattern
   for all the ISA drivers and some other Kconfig cleanups
   related to this.
 
 Cleanup:
 
 - Delete the TZ1090 GPIO drivers following the deletion of
   this SoC from the ARM tree.
 
 - Move the documentation over to driver-api to conform with
   the rest of the kernel documentation build.
 
 - Continue to make the GPIO drivers include only
   <linux/gpio/driver.h> and not the too broad <linux/gpio.h>
   that we want to get rid of.
 
 - Managed to remove VLA allocation from two drivers pending
   more fixes in this area for the next merge window.
 
 - Misc janitorial fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJaxIehAAoJEEEQszewGV1zlEAP/3p3E6J8vPqJNV/C39c40krC
 ajo0ndiTC7cotmCXNQOl9xfMCTgkjBtx3WEKwTDfCsuWW+2YB0DRmMd0Bkf2RWjQ
 nM4rB64FzAu+rdD9jdGtfn24ofylSRFaHNQ/V8Prc2JVAXJt4DS97h+6kwzIAqCm
 A/xXQAx67k5qoTXLvR2n/8LX8TphSe2kwH/f/3/lJpNLfLCRRJ3GqJfpa72jw2eL
 4VIPc6KmttkqzJ1GFtzLPfhkhRr0p4sSzUNydlj5BKhmOSVu6Afv5ylgpK/p38dQ
 mGvNqFnU0lpwelsoZK75YikDFbqQjn4XkXJGvmIRMw4qM7crcw5oSkeMwCrcGqJW
 7Uo7NoQU94wcQSZTppFQdaJs7NHdcnpW7jcfRYYetZL/6eDGBtfxoym90Lyjvaqs
 y+ykofbadI0X/9omO5j+qozvIneLam/CF7iDRUb/5t1LJbNwtXUsVYhz3FuwPDt1
 ZHb6w+np9ZHN6H9jz3b/F9B/uQt54pshm7NorSXrJvZfKrv8kV14MoHgYsuQDDjV
 khbveygB8DwaPeV4XjpLeYhJB1L/Wjf46CVD6tyaCRDByGQmdoJEQF9QB2CxrF2J
 ouaaaS8tSC0IK/mKMMgJxC1Vr2gh0NMlQ3AL9EJDJvX+9RoIA2gwtBAiGnlEcdq3
 GyFAZ0szb5P4BaNnX9qc
 =C5t5
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.17 kernel cycle:

  New drivers:

   - Nintendo Wii GameCube GPIO, known as "Hollywood"

   - Raspberry Pi mailbox service GPIO expander

   - Spreadtrum main SC9860 SoC and IEC GPIO controllers.

  Improvements:

   - Implemented .get_multiple() callback for most of the
     high-performance industrial GPIO cards for the ISA bus.

   - ISA GPIO drivers now select the ISA_BUS_API instead of depending on
     it. This is merged with the same pattern for all the ISA drivers
     and some other Kconfig cleanups related to this.

  Cleanup:

   - Delete the TZ1090 GPIO drivers following the deletion of this SoC
     from the ARM tree.

   - Move the documentation over to driver-api to conform with the rest
     of the kernel documentation build.

   - Continue to make the GPIO drivers include only
     <linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
     want to get rid of.

   - Managed to remove VLA allocation from two drivers pending more
     fixes in this area for the next merge window.

   - Misc janitorial fixes"

* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
  gpio: Add Spreadtrum PMIC EIC driver support
  gpio: Add Spreadtrum EIC driver support
  dt-bindings: gpio: Add Spreadtrum EIC controller documentation
  gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
  pinctrl: qcom: Don't allow protected pins to be requested
  gpiolib: Support 'gpio-reserved-ranges' property
  gpiolib: Change bitmap allocation to kmalloc_array
  gpiolib: Extract mask allocation into subroutine
  dt-bindings: gpio: Add a gpio-reserved-ranges property
  gpio: mockup: fix a potential crash when creating debugfs entries
  gpio: pca953x: add compatibility for pcal6524 and pcal9555a
  gpio: dwapb: Add support for a bus clock
  gpio: Remove VLA from xra1403 driver
  gpio: Remove VLA from MAX3191X driver
  gpio: ws16c48: Implement get_multiple callback
  gpio: gpio-mm: Implement get_multiple callback
  gpio: 104-idi-48: Implement get_multiple callback
  gpio: 104-dio-48e: Implement get_multiple callback
  gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
  gpio: pci-idio-16: Implement get_multiple callback
  ...
2018-04-05 09:51:41 -07:00
William Breathitt Gray 1f8f93683d iio: Change ISA_BUS_API dependency to selection
The ISA_BUS_API Kconfig option enables the compilation of the ISA bus
driver. The ISA bus driver does not perform any hardware interaction,
and is instead just a thin layer of software abstraction to eliminate
boilerplate code common to ISA-style device drivers. Since ISA_BUS_API
has no dependencies and does not jeopardize the integrity of the system
when enabled, drivers should select it when the ISA bus driver
functionality is needed.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22 16:13:41 +01:00
Greg Kroah-Hartman 59142f808a First round of new devices, features and cleanups for IIO in the 4.17 cycle.
Outside of IIO
 * Strongly typed 64bit int_sqrt function needed by the mlx90632
 
 New device support
 * adc081s
   - New driver supporting adc081s, adc101s and adc121s TI ADCs.
 * ad5272
   - New driver supproting the ad5272 and ad5274 ADI digital potentiometers
     with DT bindings.
 * axp20x_adc
   - support the AXP813 ADC - includes rework patches to prepare for this.
 * mlx90632
   - New driver with dt bindings for this IR temperature sensor.
 
 Features
 * axp20x_adc
   - Add DT bindings and probing.
 * dht11
   - The sensor has a wider range than advertised in the datasheet - support it.
 * st_lsm6dsx
   - Add hardware timestamp su9pport.
 
 Cleanups
 * ABI docs
   - Update email contact for Matt Ranostay
 * SPDX changes
   - Matt Ranostay has moved his drivers over to SPDX.  Currently we are making
     this an author choice in IIO.
 * ad7192
   - Disable burnout current on misconfiguration.  No actually effect as
     they simply won't work otherwise.
 * ad7476
   - Drop a license definition that was replicating information in SPDX tag.
 * ade7758
   - Expand buf_lock to cover both buffer and state protection allowing
     unintented uses of mlock in the core to be removed.
 * ade7759
   - Align parameters to opening parenthesis.
 * at91_adc
   - Depend on sysfs instead of selecting it - for try wide consistency.
 * ccs811
   - trivial naming type for a define.
 * ep93xx
   - Drop a redundant return as a result checking platform_get_resource.
 * hts221
   - Regmap conversion which simplifies the driver somewhat.
   - Clean up some restricted endian cast warnings.
   - Drop a trailing whitespace from a comment
   - Drop an unnecessary get_unaligned by changing to the right 16bit data type.
 * ms5611
   - Fix coding style in the probe function (whitespace)
 * st_accel
   - Use strlcpy instead of strncpy to avoid potentially truncating a string.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlqL3RIRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0Foiq7w//eKBOgTy0osSkLjSXACsJ0oizUoEGDV3t
 NxQ3D3el+1ATUd2tJL33gDvCzYw5DPcNcy3Hh/tl5svnwdV0WvBwIDIgdPfPBJQu
 LpBjT6bI2MwYdi1WLHZJBeoIXxg0PMF4GNZ2DIk0GL0WJg87n6SkZCmslW8Rv8BD
 NE8m9Qv72vhhZ9QjcBPoQYzRAY16moaX+9a36TBgtgGs7c5vHYNGNxoMn6sZ3sQk
 VbUtqWv9By3gp0mUg7T2Qb+62d04MbDk3Sa/K2B0COBOCSP7kWjg9h7KP902R6rU
 WNsTK+rVRHxV5Jm6PBPcit4HeSK3/9308EKkv2axQrPqCLM50GoxoqAhNq7UpAEu
 YXLi4f0te7sEQdt2QFDCdDMk1HjI3eCA7a8enBpex3gt7bdGTMQH9qDKdsWE+z4G
 Gm9xbZn+z7wNfowf5wAE16Y+yUS4UvVXawWD8FSIpKi3HvvyYS1I0nTnzvTvS/C3
 EhubRf+nguYsFjHB+LpA3II6b/NlrkKGO8PDzCr3kvfPUVErTWPgVzx6+5vPG2Gd
 6qhoFVanV7SuHD0lSq9tKQfsh0DFjAh6DQYdLpoFaxgIJi6cLCGbwOMY49ihYfSO
 mTMz5c52mJACOpq7W5e9xzvLwx6pxiQobeun3fq7kDdq5vUweKSGK4iggEZ+sr2N
 luFxzN7VLNA=
 =CH1K
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First round of new devices, features and cleanups for IIO in the 4.17 cycle.

Outside of IIO
* Strongly typed 64bit int_sqrt function needed by the mlx90632

New device support
* adc081s
  - New driver supporting adc081s, adc101s and adc121s TI ADCs.
* ad5272
  - New driver supproting the ad5272 and ad5274 ADI digital potentiometers
    with DT bindings.
* axp20x_adc
  - support the AXP813 ADC - includes rework patches to prepare for this.
* mlx90632
  - New driver with dt bindings for this IR temperature sensor.

Features
* axp20x_adc
  - Add DT bindings and probing.
* dht11
  - The sensor has a wider range than advertised in the datasheet - support it.
* st_lsm6dsx
  - Add hardware timestamp su9pport.

Cleanups
* ABI docs
  - Update email contact for Matt Ranostay
* SPDX changes
  - Matt Ranostay has moved his drivers over to SPDX.  Currently we are making
    this an author choice in IIO.
* ad7192
  - Disable burnout current on misconfiguration.  No actually effect as
    they simply won't work otherwise.
* ad7476
  - Drop a license definition that was replicating information in SPDX tag.
* ade7758
  - Expand buf_lock to cover both buffer and state protection allowing
    unintented uses of mlock in the core to be removed.
* ade7759
  - Align parameters to opening parenthesis.
* at91_adc
  - Depend on sysfs instead of selecting it - for try wide consistency.
* ccs811
  - trivial naming type for a define.
* ep93xx
  - Drop a redundant return as a result checking platform_get_resource.
* hts221
  - Regmap conversion which simplifies the driver somewhat.
  - Clean up some restricted endian cast warnings.
  - Drop a trailing whitespace from a comment
  - Drop an unnecessary get_unaligned by changing to the right 16bit data type.
* ms5611
  - Fix coding style in the probe function (whitespace)
* st_accel
  - Use strlcpy instead of strncpy to avoid potentially truncating a string.
2018-02-20 10:23:17 +01:00
Linus Torvalds 5d8515bc23 Staging/IIO patches for 4.16-rc1
Here is the big Staging and IIO driver patches for 4.16-rc1.
 
 There is the normal amount of new IIO drivers added, like all releases.
 
 The networking IPX and the ncpfs filesystem are moved into the staging
 tree, as they are on their way out of the kernel due to lack of use
 anymore.
 
 The visorbus subsystem finall has started moving out of the staging tree
 to the "real" part of the kernel, and the most and fsl-mc codebases are
 almost ready to move out, that will probably happen for 4.17-rc1 if all
 goes well.
 
 Other than that, there is a bunch of license header cleanups in the
 tree, along with the normal amount of coding style churn that we all
 know and love for this codebase.  I also got frustrated at the
 Meltdown/Spectre mess and took it out on the dgnc tty driver, deleting
 huge chunks of it that were never even being used.
 
 Full details of everything is in the shortlog.
 
 All of these patches have been in linux-next for a while with no
 reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLxoA8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+yk4vgCgjeMlwhtar65DIticIRj626EFxiQAnjGmH8Kd
 d9Xz2Piq8X47uSsC/6AE
 =xxMT
 -----END PGP SIGNATURE-----

Merge tag 'staging-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging/IIO updates from Greg KH:
 "Here is the big Staging and IIO driver patches for 4.16-rc1.

  There is the normal amount of new IIO drivers added, like all
  releases.

  The networking IPX and the ncpfs filesystem are moved into the staging
  tree, as they are on their way out of the kernel due to lack of use
  anymore.

  The visorbus subsystem finall has started moving out of the staging
  tree to the "real" part of the kernel, and the most and fsl-mc
  codebases are almost ready to move out, that will probably happen for
  4.17-rc1 if all goes well.

  Other than that, there is a bunch of license header cleanups in the
  tree, along with the normal amount of coding style churn that we all
  know and love for this codebase. I also got frustrated at the
  Meltdown/Spectre mess and took it out on the dgnc tty driver, deleting
  huge chunks of it that were never even being used.

  Full details of everything is in the shortlog.

  All of these patches have been in linux-next for a while with no
  reported issues"

* tag 'staging-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (627 commits)
  staging: rtlwifi: remove redundant initialization of 'cfg_cmd'
  staging: rtl8723bs: remove a couple of redundant initializations
  staging: comedi: reformat lines to 80 chars or less
  staging: lustre: separate a connection destroy from free struct kib_conn
  Staging: rtl8723bs: Use !x instead of NULL comparison
  Staging: rtl8723bs: Remove dead code
  Staging: rtl8723bs: Change names to conform to the kernel code
  staging: ccree: Fix missing blank line after declaration
  staging: rtl8188eu: remove redundant initialization of 'pwrcfgcmd'
  staging: rtlwifi: remove unused RTLHALMAC_ST and RTLPHYDM_ST
  staging: fbtft: remove unused FB_TFT_SSD1325 kconfig
  staging: comedi: dt2811: remove redundant initialization of 'ns'
  staging: wilc1000: fix alignments to match open parenthesis
  staging: wilc1000: removed unnecessary defined enums typedef
  staging: wilc1000: remove unnecessary use of parentheses
  staging: rtl8192u: remove redundant initialization of 'timeout'
  staging: sm750fb: fix CamelCase for dispSet var
  staging: lustre: lnet/selftest: fix compile error on UP build
  staging: rtl8723bs: hal_com_phycfg: Remove unneeded semicolons
  staging: rts5208: Fix "seg_no" calculation in reset_ms_card()
  ...
2018-02-01 09:51:57 -08:00
Randy Dunlap ea9170e576 iio/adc: depend on SYSFS instead of selecting it
Drivers should not 'select' a subsystem. Instead they should depend
on it. If the subsystem is disabled, the user probably did that for
a purpose and one driver shouldn't be changing that.

This also makes all IIO drivers consistent w.r.t depending on SYSFS
instead of selecting it.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-01-30 18:33:26 +00:00
Arnaud Pouliquen e2e6771c64
IIO: ADC: add STM32 DFSDM sigma delta ADC support
Add DFSDM driver to handle sigma delta ADC.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-01-10 10:30:12 +00:00
Arnaud Pouliquen bed73904e7
IIO: ADC: add stm32 DFSDM core support
Add driver for stm32 DFSDM pheripheral. Its converts a sigma delta
stream in n bit samples through a low pass filter and an integrator.
stm32-dfsdm-core driver is the core part supporting the filter
instances dedicated to sigma-delta ADC or audio PDM microphone purpose.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-01-10 10:30:11 +00:00
Arnaud Pouliquen 8a5f0b6f6c
IIO: ADC: add sigma delta modulator support
Add generic driver to support sigma delta modulators.
Typically, this device is hardware connected to
an IIO device in charge of the conversion. Devices are
bonded through the hardware consumer API.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-01-10 10:30:09 +00:00
Andreas Klinger d3bf60450d iio: hx711: add triggered buffer support
Add buffer to device data struct and add trigger function

Data format is quite simple:
      voltage - channel 0   32 Bit
      voltage - channel 1   32 Bit
      timestamp             64 Bit

Using both channels at the same time is working quite slow because of
changing the channel which needs a dummy read.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-08 16:03:42 +01:00
Eugen Hristev 073c662017 iio: adc: at91-sama5d2_adc: add support for DMA
Added support for DMA transfers. The implementation uses the user watermark
to decide whether DMA will be used or not. For watermark 1, DMA will not be
used. If watermark is bigger, DMA will be used.
Sysfs attributes are created to indicate whether the DMA is used,
with hwfifo_enabled, and the current DMA watermark is readable
in hwfifo_watermark. Minimum and maximum values are in hwfifo_watermark_min
and hwfifo_watermark_max.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-12-02 10:39:43 +00:00
Greg Kroah-Hartman 7706abf5a0 Merge 4.14-rc6 into staging-next
We want the IIO and staging driver fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-23 14:29:43 +02:00
Lukas Wunner c1375d671a iio: adc: mcp320x: Add support for mcp3550/1/3
These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but
in reality their resolution is 21 bit with an overrange or underrange
of 12% beyond Vref.  In other words, "full scale" means +/- 2^20.

This driver does not explicitly signal back to the user when an
overrange or underrange occurs, but the user can detect it by comparing
the raw value to +/- 2^20 (or the scaled value to Vref).

The chips feature an extended temperature range and high accuracy,
low noise characteristics, but their conversion times are slow with
up to 80 ms +/- 2% (on the MCP3550-50).

Hence, unlike the other ADCs supported by the driver, conversion does
not take place in realtime upon lowering CS.  Instead, CS is asserted
for 8 usec to start the conversion.  After waiting for the duration of
the conversion, the result can be fetched.  While waiting, control of
the bus is ceased so it may be used by a different device.

After the result has been fetched and 10 us have passed, the chip goes
into shutdown and an additional power-up delay of 144 clock periods is
then required to wake the analog circuitry upon the next conversion
(footnote below table 4-1, page 16 in the spec).

Optionally, the chips can be used in so-called "continuous conversion
mode":  Conversions then take place continuously and the last result may
be fetched at any time without observing a delay.  The mode is enabled
by permanently driving CS low, e.g. by wiring it to ground.  The driver
only supports "single conversion mode" for now but should be adaptable
to "continuous conversion mode" with moderate effort.

The chips clock out a 3 byte word, unlike the other ADCs supported by
the driver which all have a lower resolution than 16 bit and thus make
do with 2 bytes.  Calculate the word length on probe by rounding up the
resolution to full bytes.  Crucially, if the clock idles low, the
transfer is preceded by a useless Data Ready bit which increases its
length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec).
Autosense this based on the SPI slave's configuration.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-09 21:01:36 +01:00
Geert Uytterhoeven af5d716a90 iio: adc: rcar-gyroadc: Enable compile-testing on non-ARM
The rcar-gyroadc driver compiles fine on other platforms, hence increase
compile coverage.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-09 20:50:46 +01:00
Randy Dunlap 5151b4afb4 iio: adc: dln2-adc: fix build error
The dln2-adc driver uses interface(s) that are controlled by the
IIO_TRIGGERED_BUFFER Kconfig symbol, so the driver needs to select
that symbol to prevent the build error.

drivers/iio/adc/dln2-adc.o: In function `dln2_adc_probe':
dln2-adc.c:(.text+0x528): undefined reference to `devm_iio_triggered_buffer_setup'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-08 11:42:00 +01:00
Arnd Bergmann 3f09b8d2ea iio: adc: select triggered buffer for sama5d2 adc
Without the triggered buffer code, we get a link error:

drivers/iio/adc/at91-sama5d2_adc.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x938): undefined reference to `devm_iio_triggered_buffer_setup'

This adds a Kconfig 'select' statement like other ADC
drivers have it already.

Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-17 15:37:14 +01:00
Alexander Sverdlin 8614206a05 iio: adc: New driver for Cirrus Logic EP93xx ADC
New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-25 19:56:23 +01:00
Jack Andersen 7c0299e879 iio: adc: Add support for DLN2 ADC
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.

Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-09 18:17:18 +01:00
Mike Looijmans 1d3eacbfa6 iio: Add LTC2471/LTC2473 driver
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.

Datasheet:
  http://cds.linear.com/docs/en/datasheet/24713fb.pdf

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-04 20:50:04 +01:00
Fabio Estevam edd80a5f51 iio: adc: Kconfig: Append vendor name for IMX7D_ADC
To keep IMX7D_ADC text consistent with other iio/adc entries, add
the vendor name to the driver menu text.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-01 10:16:38 +01:00
Greg Kroah-Hartman ca9280d1f8 First set of new device support, features and cleanups for IIO in the 4.13 cycle
Two entirely new drivers in here plus the usual range of cleanups and features.
 
 New device support
 * ad5064
   - add ltc2631, ltc2633 and ltc2635 support.
 * bma180
   - trivial support for bma250e (new id)
 * hid-sensor-rotation
   - add relative orientation and geometric orientation support.
 * isl29028
   - add isl29030 support (its effectively the same part from a driver point of
   view)
 * maxim_thermocouple
   - add max31856 id.
 * meson-saradc
   - add meson8b SoC adc support.
 * ti-adc084s021
   - new driver and bindings.
 * ti-adc108s102
   - new driver and bindings.
 
 Staging graduations
 * isl29028
 
 Features
 * bma180
   - ACPI enumeration for BMA250E which is used in various x86 tablets.
 * hi8453
   - add raw access rather than only events.
 * hid-sensor-hub
   - Implement batch mode in which we can set a threshold on the amount of time
   between data coming from the fifos.  This is the first device to do this
   rather than use a watershed on the number of samples.
 * hts221
   - power management support
 * lsm6dsx
   - add system power management support.
 * rpr0521
   - sampling frequency read / write
 * stm32-trigger
   - add support for TRG02 triggers.
 * tsl2583
   - runtime power management support.
 
 Cleanups
 * core
   - inkern: fix a double unlock in iio_read_available_channel_raw when raw
   value doesn't appear to be raw (error path).
   - fixup accidental sizeof pointer in iio_device_add_mask_type.
 * docs
   - fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
 * tools
   - use local include/uapi headers to ensure always up to date.
   - increase length of allowed trigger names.
 * ad9834
   - symbolic to octal permissions.
 * ade7753
   - symbolic to octal permissions.
   - fix indentation
 * ade7754
   - symbolic to octal permissions.
 * ade7758
   - symbolic to octal permissions.
 - ade7854
   - symbolic to octal permissions.
 * as3935
   - move out of storm check to given consistent results for raw and processed
   values.
 * bmp280
   - fix bme280 naming in Kconfig help.
 * hi8435
   - avoid garbage on event after enable.
   - add missing in_voltage_sensing_mode_available to list possible enum options.
   - handle the reset gpio with the obvious polarity rather than relying on
   DT to provide it correctly.
 * hid-sensors
   - fix a wrong error path scrubbing of return values.
 * hid-sensors-accel
   - drop static on a local variable
 * hid-sensors-rotation
   - Add missing scale and offset property parsing support.
 * ina2xx
   - Fix a bad use of GENMASK and some typos and whitespace issues.
 * isl29018
   - only declare the ACPI table when ACPI is enabled.
 * isl29028
   - fix proximity sleep times.
 * lsm6dsx
   - replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
   dealing with the various PM config variables.
 * meson-saradc
   - mark meson_sar_adc_data static and const.
 * rcar-gyroadc
   - derive the interface clock speed from the fck clock on the basis they are
   the same actual clock.
   - drop the now unused if clock from the bindings.
 * rpr0521
   - disable sensor when marked as such rather than always enabling it.
   - poweroff if probe fails and we can talk to device.
   - make sure device powered off when it doesn't need to be on.
   - use sizeof rather than hardcoded size on value read.
   - whitespace fixup.
   - reorder channel numbers ready for buffered support which didn't quite
   make this pull request.
 * st-accel
   - fix platform data initialization to allow remove and reprobe.
 * st-pressure
   - fix platform data initialization to allow remove and reprobe.
 * tsl2x7x
   - S_IRUGO, S_IWUSR to octal values
   - rename driver for consistency with more recent drivers
   - drop FSF mailing address
   - replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
   relevant function renames.
 * zpa2326
   - report an error for consistency with other error paths.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlkjSHkRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FojDqQ//TVibBBZ0GgA+MwjIMDCpYL6CW4l+Et5v
 bD1EThc+qf3jv9kWbBz6WgySj9koZeF/hc0GN7x8XF57TeF/8sXhtbZKQ0za0Ouf
 uKAfYNi7jtdA4UEFawYrFUGIZtgQlbll/DKj7x2yDZtwIge9QF61fzPehGpq0u3b
 IiNlNFQSTKXOHi5tobMXXdBFL90m6kqDZM5ZwAWtQoSu1xQTjCsxu/LMJAJ3H7rU
 KEptEhc80kAvGqflOvw/HMaU7O7SXAhW3sQnXM2ksnDScGZ+zNzLcoca1YfM73rv
 x3vM/XL93A6CcRQkzFUC5vbtVVl00BMI7G3PQTGDOWWPgUPksLVIzfJR9GOqNmIJ
 W3HVwQbDZPvAbubvFHlUBa9ys4cbcmwU9214S57DvzVEt+cvpdujjIZ2Ulw3sVqN
 3xB1P9kNlcYvmBBu6LbP5GTDEu+VEETTjwj3osyimi56Zt44pJhoT68D46SD34Zw
 i3LCMFbbdJzEK4UWsvoBKFsTPipXgOntYDXaMZbULjtmJ6PEw0feubQIpMwtF5iw
 4fGk/1Q6l//rItJlXZE9PPiEBbXZ856lk/KQn+9vRABCrFni+7HWf6aDvkjf14o0
 8W+P/kAcXOPrToN2+NnAbIh7c9PLYmFWJa7DvDnQ5Guy0GStlxG18QEMNAhf39/0
 j/xopB1g8MI=
 =XLVY
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 4.13 cycle

Two entirely new drivers in here plus the usual range of cleanups and features.

New device support
* ad5064
  - add ltc2631, ltc2633 and ltc2635 support.
* bma180
  - trivial support for bma250e (new id)
* hid-sensor-rotation
  - add relative orientation and geometric orientation support.
* isl29028
  - add isl29030 support (its effectively the same part from a driver point of
  view)
* maxim_thermocouple
  - add max31856 id.
* meson-saradc
  - add meson8b SoC adc support.
* ti-adc084s021
  - new driver and bindings.
* ti-adc108s102
  - new driver and bindings.

Staging graduations
* isl29028

Features
* bma180
  - ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
  - add raw access rather than only events.
* hid-sensor-hub
  - Implement batch mode in which we can set a threshold on the amount of time
  between data coming from the fifos.  This is the first device to do this
  rather than use a watershed on the number of samples.
* hts221
  - power management support
* lsm6dsx
  - add system power management support.
* rpr0521
  - sampling frequency read / write
* stm32-trigger
  - add support for TRG02 triggers.
* tsl2583
  - runtime power management support.

Cleanups
* core
  - inkern: fix a double unlock in iio_read_available_channel_raw when raw
  value doesn't appear to be raw (error path).
  - fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
  - fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
  - use local include/uapi headers to ensure always up to date.
  - increase length of allowed trigger names.
* ad9834
  - symbolic to octal permissions.
* ade7753
  - symbolic to octal permissions.
  - fix indentation
* ade7754
  - symbolic to octal permissions.
* ade7758
  - symbolic to octal permissions.
- ade7854
  - symbolic to octal permissions.
* as3935
  - move out of storm check to given consistent results for raw and processed
  values.
* bmp280
  - fix bme280 naming in Kconfig help.
* hi8435
  - avoid garbage on event after enable.
  - add missing in_voltage_sensing_mode_available to list possible enum options.
  - handle the reset gpio with the obvious polarity rather than relying on
  DT to provide it correctly.
* hid-sensors
  - fix a wrong error path scrubbing of return values.
* hid-sensors-accel
  - drop static on a local variable
* hid-sensors-rotation
  - Add missing scale and offset property parsing support.
* ina2xx
  - Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
  - only declare the ACPI table when ACPI is enabled.
* isl29028
  - fix proximity sleep times.
* lsm6dsx
  - replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
  dealing with the various PM config variables.
* meson-saradc
  - mark meson_sar_adc_data static and const.
* rcar-gyroadc
  - derive the interface clock speed from the fck clock on the basis they are
  the same actual clock.
  - drop the now unused if clock from the bindings.
* rpr0521
  - disable sensor when marked as such rather than always enabling it.
  - poweroff if probe fails and we can talk to device.
  - make sure device powered off when it doesn't need to be on.
  - use sizeof rather than hardcoded size on value read.
  - whitespace fixup.
  - reorder channel numbers ready for buffered support which didn't quite
  make this pull request.
* st-accel
  - fix platform data initialization to allow remove and reprobe.
* st-pressure
  - fix platform data initialization to allow remove and reprobe.
* tsl2x7x
  - S_IRUGO, S_IWUSR to octal values
  - rename driver for consistency with more recent drivers
  - drop FSF mailing address
  - replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
  relevant function renames.
* zpa2326
  - report an error for consistency with other error paths.
2017-05-29 15:53:42 +02:00
Jan Kiszka 7e87d11c9b iio: adc: Add support for TI ADC108S102 and ADC128S102
This is an upstream port of an IIO driver for the TI ADC108S102 and
ADC128S102. The former can be found on the Intel Galileo Gen2 and the
Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
included.

Due to the lack of regulators under ACPI, we hard-code the voltage
provided to the VA pin of the ADC to 5 V, the value used on Galileo and
IOT2000. For DT usage, the regulator "vref-supply" provides this
information. Note that DT usage has not been tested.

Original author: Bogdan Pricop <bogdan.pricop@emutex.com>
Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
Todor Minchev <todor@minchev.co.uk>.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-05-21 15:11:14 +01:00
Mårten Lindahl 3691e5a694 iio: adc: add driver for the ti-adc084s021 chip
This adds support for the Texas Instruments ADC084S021 ADC chip.

Signed-off-by: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-05-14 16:34:11 +01:00
Linus Torvalds c6a677c6f3 Staging/IIO patches for 4.12-rc1
Here is the big staging tree update for 4.12-rc1.  And it's a big one,
 adding about 350k new lines of crap^Wcode, mostly all in a big dump of
 media drivers from Intel.  But there's other new drivers in here as
 well, yet-another-wifi driver, new IIO drivers, and a new crypto
 accelerator.  We also deleted a bunch of stuff, mostly in patch
 cleanups, but also the Android ION code has shrunk a lot, and the
 Android low memory killer driver was finally deleted, much to the
 celebration of the -mm developers.
 
 All of these have been in linux-next with a few build issues that will
 show up when you merge to your tree, I'll follow up with fixes for those
 after this gets merged.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQzzlQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ylNMgCcD+GoaF/Ml7YnULRl2GG/526II78AnitZ8qjd
 rPqeowMIewYu9fgckLUc
 =7rzO
 -----END PGP SIGNATURE-----

Merge tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging/IIO updates from Greg KH:
 "Here is the big staging tree update for 4.12-rc1.

  It's a big one, adding about 350k new lines of crap^Wcode, mostly all
  in a big dump of media drivers from Intel. But there's other new
  drivers in here as well, yet-another-wifi driver, new IIO drivers, and
  a new crypto accelerator.

  We also deleted a bunch of stuff, mostly in patch cleanups, but also
  the Android ION code has shrunk a lot, and the Android low memory
  killer driver was finally deleted, much to the celebration of the -mm
  developers.

  All of these have been in linux-next with a few build issues that will
  show up when you merge to your tree"

Merge conflicts in the new rtl8723bs driver (due to the wifi changes
this merge window) handled as per linux-next, courtesy of Stephen
Rothwell.

* tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1182 commits)
  staging: fsl-mc/dpio: add cpu <--> LE conversion for dpaa2_fd
  staging: ks7010: remove line continuations in quoted strings
  staging: vt6656: use tabs instead of spaces
  staging: android: ion: Fix unnecessary initialization of static variable
  staging: media: atomisp: fix range checking on clk_num
  staging: media: atomisp: fix misspelled word in comment
  staging: media: atomisp: kmap() can't fail
  staging: atomisp: remove #ifdef for runtime PM functions
  staging: atomisp: satm include directory is gone
  atomisp: remove some more unused files
  atomisp: remove hmm_load/store/clear indirections
  atomisp: kill off mmgr_free
  atomisp: clean up the hmm init/cleanup indirections
  atomisp: handle allocation calls before init in the hmm layer
  staging: fsl-dpaa2/eth: Add maintainer for Ethernet driver
  staging: fsl-dpaa2/eth: Add TODO file
  staging: fsl-dpaa2/eth: Add trace points
  staging: fsl-dpaa2/eth: Add driver specific stats
  staging: fsl-dpaa2/eth: Add ethtool support
  staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver
  ...
2017-05-05 18:16:23 -07:00
Quentin Schulz 0e34d5de96 iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs
The X-Powers AXP20X and AXP22X PMICs have multiple ADCs. They expose the
battery voltage, battery charge and discharge currents, AC-in and VBUS
voltages and currents, 2 GPIOs muxable in ADC mode and PMIC temperature.

This adds support for most of AXP20X and AXP22X ADCs.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-04-27 09:25:07 +01:00
Akinobu Mita a9e9c7153e iio: adc: add max1117/max1118/max1119 ADC driver
This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.

This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.

1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1.  The chip select line must be brought
high and low again without transfer.

2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete.  The conversion
begins with the falling edge of the chip select.  During the conversion
process, SCLK is ignored.

These two usages are unusual.  But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)

On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work.  But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-14 15:09:06 +01:00
Linus Walleij 63c3ecd946 iio: adc: add a driver for Qualcomm PM8xxx HK/XOADC
The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).

As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.

This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.

Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:42:26 +01:00
Linus Walleij e932d4f041 iio: adc: break out common code from SPMI VADC
The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.

As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:40:49 +01:00
Quentin Schulz 808a8b7377 iio: adc: sun4i-gpadc-iio: add support for A33 thermal sensor
This adds support for the Allwinner A33 thermal sensor.

Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.

The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.

Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).

The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:35:47 +01:00
Jacopo Mondi 69780a3bbc iio: adc: Add Maxim max9611 ADC driver
Add iio driver for Maxim max9611 and max9612 current-sense amplifiers
with 12-bits ADC interface.

Datasheet publicly available at:
https://datasheets.maximintegrated.com/en/ds/MAX9611-MAX9612.pdf

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:26:06 +01:00
Arnd Bergmann be2d732086 iio: adc: sun4i: add THERMAL dependency
With CONFIG_THERMAL=m and CONFIG_SUN4I_GPADC=y, we get a link error
from calling devm_thermal_zone_of_sensor_register:

drivers/iio/built-in.o: In function `sun4i_gpadc_probe':
:(.text+0x1c284): undefined reference to `devm_thermal_zone_of_sensor_register'

This adds a Kconfig dependency to ensure we can only have the ADC
driver as built-in when this function is also built-in, or when
we see the empty stub implementation. When the thermal code is
a module, we can still build the adc driver as a module, too.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-02 11:36:27 +01:00
Michael Hennerich bc82222fcc iio:adc: Driver for Linear Technology LTC2497 ADC
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-02 10:56:59 +01:00
Rick Altherr 573803234e iio: Aspeed ADC
Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold
interrupts are supported by the hardware but are not currently implemented.

Signed-off-by: Rick Altherr <raltherr@google.com>
Tested-by: Xo Wang <xow@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-01 11:53:20 +01:00
Tony Lindgren 25ec249632 iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC
On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.

Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.

Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-03-30 19:25:23 +01:00
Ksenija Stanojevic 0d690cc41b iio: adc: mxs-lradc: Remove driver
Since the driver has been split into MFD there is no reason for it to
stay, so remove it.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-23 12:29:01 +00:00