No use printing addresses of pointers, just print the
pointers themselves.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
/<debugfs_root>/ieee80211/phyX/ath9k/regdump is the interface
to dump the registers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AID and BSSID should be set in the HW only for the
first station interface or adhoc interface. Also, cancel
the ANI timer in stop() for multi-STA scenario. And finally
configure the HW beacon timers only for the first station
interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 doesn't use the default GPIO pin for LED and GPIO 6 is actually
used for this.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stream length/tag fields have to be in little endian
format. Fixing this makes the driver work on big-endian
platforms.
Cc: stable@kernel.org
Tested-by: raghunathan.kailasanathan@wipro.com
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize txq to avoid this warning:
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_flush’:
drivers/net/wireless/ath/ath9k/main.c:2138: warning: ‘txq’ may be used uninitialized in this function
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pll_work should be cancelled on full_sleep or it may cause
redundant chip reset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4df3071ebd "ath9k_hw: optimize
interrupt mask changes", changed ath9k_hw_set_interrupts function to
enable interrupts regardless of function argument, what could possibly
be wrong. Correct that behaviour and check "ints" arguments before
enabling interrupts, also disable interrupts if ints do not have
ATH9K_INT_GLOBAL flag set.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hif_usb_alloc_urbs() takes care of freeing
all the allocated URBs for the various endpoints when
an error occurs. Calling ath9k_hif_usb_dealloc_urbs() would
cause a panic since the URBs have already been freed.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH9K_RX_FILTER_UNCOMP_BA_BAR and ATH9K_RX_FILTER_PSPOLL
when mac80211 requires it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to set the BSSID mask or opmode when
initializing RX, they would be set correctly in the HW reset
routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The target beacon transmission time has to be synced with the HW
TSF when configuring beacon timers in Adhoc mode. Failing to do this
would cause erroneous beacon transmission, for example, on completion
of a scan run to check for IBSS merges.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle multi-interface situations by checking if
AP interfaces are already present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time granularity for the ANI task is different for AP and
station mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for allowing only one IBSS interface to be
configured.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required when issuing commands to the firmware.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to use a locally stored reference.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 stores the association state in ieee80211_bss_conf.
Use this and remove the local state, which is incorrect anyway
since it is stored globally and not on a per-VIF basis.
Restarting ANI and reconfiguration of HW beacon timers when a
scan run ends requires more work. This is handled by iterating
over the active interfaces.
Finally, remove the useless check for associated status in RX
processing.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTS protection can be obtained from mac80211 directly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's BSS info can be used for this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition of a station might fail - handle this error
properly by removing the VAP on the target.
Also, bail out immediately if the max. no of interfaces
has been reached.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update capabilites on the target once, when
start() is called, there is no need for redundant
updating on adding an interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple interfaces can be configured if a slot is free
on the target. Monitor mode also requires a slot.
The maximum number of stations that can be handled in
the firmware is 8, manage the station slots accordingly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some AR7010 based devices are recognized as storage media.
Sending a CD-EJECT command to the device will 'convert' it into
a WLAN device. Do this within the driver itself, removing the
dependancy on an external program (usb_modeswitch).
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: add an extra delay when reseting AR_RTC_RESET"
added an extra udelay to the reset routine. As the required
delay is already present, remove this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When op_flush() is called with no drop (drop=false), the driver
tries to tx as many frames as possible in about 100ms on every
hw queue. During this time period frames from sw queue are also
scheduled on to respective hw queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize caldata to avoid compilation warning.
CC [M] drivers/net/wireless/ath/ath9k/htc_drv_main.o
drivers/net/wireless/ath/ath9k/htc_drv_main.c: In function ‘ath9k_htc_config’:
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: warning: ‘caldata’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: note: ‘caldata’ was declared here
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beaconing should be disabled before stopping beacon queue.
Not doing so could queue up beacons in hw that causes
failure to stop Tx DMA, due to pending frames in hw
and also unnecessary beacon tasklet schedule.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable appears in both ath_softc and ath_beacon_config.
The struct ath_beacon_config is embedded in ath_softc. The redundant
variable was added by commit id 57c4d7b4c4.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Reviewed-by: Mohammed Shafi <shafi.ath9k@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add few comments for not parsing DTIM period from mac80211
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since even with the latest changes the false positive issue of the baseband
hang check is not fully solved yet, additional checks are needed.
If the baseband hang occurs, the rx_clear signal will be stuck to high, so
we can use the cycle counters to confirm it.
With this patch, a hardware reset is only triggered if the baseband hang
check returned true three times in a row, with a beacon interval between
each check and if the busy time was also 99% or more during the check
intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beaconing vif addition is based on max beacon slot
available. So it is better to reserve a beacon slot
on interface addition and let it be configured properly
on bss_info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The opmode recalculation is accessing hw registers.
When it is called from remove interface callback and
if there are no vifs present then hw is moved to FULL SLEEP
by radio disable. So use power save wrappers before
accessing hw registers in calculating opmode state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
move ath_update_txpow to common to remove code duplication
in both ath9k & ath9k_htc.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ani work is cancelled in dissaoctiation. But in some cases
during suspend, deauthention never be called. So we failed
to stop ani work which was identified by the following
warning.
Call Trace:
[<ffffffffa0454a1d>] ieee80211_can_queue_work.clone.17+0x2d/0x40 [mac80211]
[<ffffffffa0454a60>] ieee80211_queue_delayed_work+0x30/0x60 [mac80211]
[<ffffffffa0567f82>] ath9k_ani_work+0x142/0x250 [ath9k_htc]
[<ffffffff81073c70>] async_run_entry_fn+0x0/0x180
[<ffffffffa0567e40>] ath9k_ani_work+0x0/0x250 [ath9k_htc]
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: fix tx queue index confusion in debugfs code" changed the debug
function but not the stub.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change from the systems team to update PMU setting for AR9485
version of chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spin_lock has been tried to be acquired twice from ath9k_tasklet
to ath_reset which resulted in a machine freeze.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updates from the analog team for AR9485 chipsets to set
DDR_PLL2 and DDR_PLL3. Also program the BB_PLL ki
and kd value.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this PLL hang issue is seen, both Rx and Tx fail to work.
The sqsum_dvc needs to be below 2000 for a good chip. During
this issue the sqsum_dvc value is beyond 80000 and only a
full reset can solve this problem.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a function to observe the delta VC of BB_PLL.
For a good chip, the sqsum_dvc is below 2000.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has separate filter masks for compressed/uncompressed
BlockAcks and BlockAckRequests. Add them.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c"
changed the behavior of INI overriding which is needed only
for PCI cards. Revert to the original check.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: Relocate Opmode initialization"
moved the opmode initialization before the STA_ID1 register
was programmed with defaults. This changed the original
behaviour because the re-programming code doesn't take into
account the existing value in the register. Both ath9k and ath9k_htc
were not affected by this change because the opmode is
re-initialized after every reset, when RX is started.
Revert to the original behavior, except keep it outside the
REGWRITE block. This would help remove extraneous opmode calls
in the driver core.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_WEP_NKID is not used in ath9k any more since the key handling code
has been moved to ath/.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various places printing tx queue information used various different ways to
get a tx queue index for printing statistics. Most of these ways were wrong.
ATH_TXQ_AC_* cannot be used as an index for sc->tx.txq, because it is only
used internally for queue assignment.
One place used WME_AC_* as a queue index for sc->debug.stats.txstats, however
this array uses the ath9k_hw queue number as well.
Fix all of this by always using the ath9k_hw queue number as an index, and
always looking it up by going through sc->tx.txq_map.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.
By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 'ath9k: Add more information to debugfs xmit file.' added more
debug counters to ath9k and also added some lines of code to ath9k_hw.
Since ath9k_hw is also used by ath9k_htc, its code must not depend on ath9k
data structures. In this case it was not fatal, but it's still wrong, so
the code needs to be moved back to ath9k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused macros and cleanup buffer_type enumeration
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to read and backup AR_WA register value permanently and reading
this after the chip is awakened results in this register being zeroed out.
This seems to fix the ASPM with L1 enabled issue that we have observed.
The laptop becomes very slow and hangs mostly with ASPM L1 enabled without
this fix.
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are few places where we are checking for macversion and revsions
before RTC is powered ON. However we are reading the macversion and
revisions only after RTC is powered ON and so both macversion and
revisions are actully zero and this leads to incorrect srev checks
Incorrect srev checks can cause registers to be configured wrongly and can
cause unexpected behavior. Fixing this seems to address the ASPM issue that
we have observed. The laptop becomes very slow and hangs mostly with ASPM L1
enabled without this fix.
fix this by reading the macversion and revisisons even before we start
using them. There is no reason why should we delay reading this info
until RTC is powered on as this is just a register information.
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When beacons are being added or removed for an interface, ieee80211_beacon_get
will sometimes not return a beacon. This is normal and should not result in
useless logspam.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Try all xmit queues until the hardware buffers are full.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a misc file to show hardware op-mode, irq setup,
number of various types of VIFs and more.
Also, previous patches were using the wrong xmit queue
indexes. Change to use the internal ath9k indexes instead
of the mac80211 queue indexes.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The system can get into a state where the xmit queue
is stopped, but there are no packets pending, so
the queue will not be restarted.
Add logic to the xmit watchdog to attempt to restart
the xmit logic if this situation is detected.
Example 'dmesg' output:
ath: txq: f4e723e0 axq_qnum: 2, mac80211_qnum: 2 axq_link: f4e996c8 pending frames: 1 axq_acq empty: 1 stopped: 0 axq_depth: 0 Attempting to restart tx logic.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To try to figure out why xmit logic hangs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stations hold the ath_node, which holds the tid
and other xmit logic structures. In order to debug
stuck xmit logic, we need a way to print out the tid
state for the stations.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show counters for pkts sent directly to hardware and
those queued in software.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the txq->axq_q is empty, the code was breaking out
of the tx_processq logic without checking to see if it should
transmit other queued AMPDU frames (txq->axq_acq).
This patches ensures ath_txq_schedule is called.
This needs review.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should help debug strange tx lockup type issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I thought this might help track down stuck queues, etc.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places where ath_reset() was called without proper
calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls
directly to ath_reset and drop them from callers where it makes sense.
Also add them to the config callback around ath_update_txpow to fix a
crash that happens when the tx power changed before any vif is brought up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.
Cc: stable@kernel.org
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered. Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.
In addtion, use the vif type instead of hardware opmode
when dealing with beacons.
Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because the sendbar variable was not reset to zero, the stack would send
Block ACK requests for all subframes following the one that failed, which
could mess up the receiver side block ack window.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the first TID in the first AC's list is not available for forming
a new aggregate (the BAW might not allow it), however other TIDs may have
data available for sending.
Prevent a slowdown of other TIDs by going through multiple entries until
we've either hit the last one or enough AMPDUs are pending in the hardware
queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 carrier leakage calibration related workaround on high
temperature is not applicable for AR9271.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k_hw assumes that caldata is valid only for
oper channel. But with ath9k_htc case, the caldata is
passed for all channels on hw_reset though we are not doing
calibration on that channel. So the oper channel's nf history
got cleared to default due to mismatch in channel flags.
This patch also saves some space.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
caldata's channel info is never filled with operating channel
info which is causing the operating channel's noise floor
history buffer is reset to default nf during channel change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rx error bit parsing was changed to consider PHY errors and various
decryption errors separately. While correct according to the documentation,
this is causing spurious decryption error reports in some situations.
Fix this by restoring the original order of the checks in those places,
where the errors are meant to be mutually exclusive.
If a CRC error is reported, then MIC failure and decryption errors
are irrelevant, and a PHY error is unlikely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since baseband hangs are rare, but the hang check function has a high
false positive rate in some situations, we need to add more reliable
indicators.
In AP mode we can use blocked beacon transmissions as an indicator,
they should be rare enough.
In station mode, we can skip the hang check entirely, since a true
hang will trigger beacon loss detection, and mac80211 will rescan,
which leads to a hw reset that will bring the hardware back to life.
To make this more reliable, we need to skip fast channel changes
if the hardware appears to be stuck.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There might be some old stale data left, which could confuse tracking
of pending tx frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txtid->seq_start may not always be up to date, when there is HT non-AMPDU
traffic just before starting an AMPDU session. Relying on txtid->seq_next
is better, since it is also used to generate the sequence numbers for
all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a tid pointer is passed to ath_tx_send_normal(), it increases the
starting sequence number for the next AMPDU action frame, which should
only be done if the sequence number assignment is fresh. In this case
it is clearly not.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, reading the EEPROM data can be offloaded
to the target. Use multiple register reads to take advantage
of this feature to reduce initialization time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would decrease latency in reading bulk registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.
Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.
Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
USB devices do not require the chip test routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To inject a packet in monitor mode, a dummy station has
to be associated with the monitor interface in the target.
Failing to do this would result in a firmware crash on the device.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some obvious looking dead code and rename few functions
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 0ce3bcfc84.
Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period
Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And add the copyright/license header.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().
This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.
Cc: stable <stable@kernel.org>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the AR9002, the spur frequency read from the EEPROM is mangled
before being compared against AR_NO_SPUR. This results in the driver
trying to set up the spur mitigation for bogus spurs, rather than
cleanly breaking out.
Signed-off-by: Brian Prodoehl <bprodoehl@nomadio.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disabling BH is not required while running from a tasklet context
and so replace spin_lock_bh with just spin_lock.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like some hardware registers are left into undefined state
after suspend/resume. At minimum, this can cause odd issues related to
key cache and hardware trying to encrypt/decrypt frames unexpectedly.
This seems to happen even when there is no keys configured, i.e., hardware
can end up touching TX frames just based of invalid key cache context
even if the driver is not asking a specific entry to be used. In
addition, RX can likely be affected. This patch fixes this issue.
Signed-off-by: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The size of the eeprom data is 1088 bytes for AR9485. But
a sanity check is done against 4K which would result in a
'potential read past the end of the buffer' smatch complaint.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a missing unlock when we hit the "No beacon slot available"
error condition.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.
For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k channel table for 2Ghz does not seems to initialize the 'band'
parameter.Though it does not seems to cause any visible issue it looks
odd when we initialize the 'band' parameter for 5Ghz channel table while
not so for 2Ghz.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve aggregation length, there should not be more than two fully formed
A-MPDU frames in the hardware queue. To ensure this, the code checks the tx
queue length before forming new A-MPDUs. This can reduce the throughput (or
maybe even starve out A-MPDU traffic) when too many non-aggregated frames are
in the queue.
Fix this by keeping track of pending A-MPDU frames (even when they're sent out
as single frames), but exclude rate control probing frames to improve
performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the drop in Tx power for a particular mcs rate exceeds
the paprd scale factor, paprd may not work properly. Disable
paprd for any such rates.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add multiple Tx IQ cal support to improve EVM accross
different power levels.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper can be used in multiple places. Also make
it inline returning u8.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PM-QOS value can be user specified via module parameter.
This patch adds few comments regarding this in the driver
code.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not required for USB devices.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.
The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the pm-qos value to be user configurable by making it as
a module parameter.This will help our customers to configure the pm-qos
value according to the effect in throughput due to the DMA latency problem
which was observed in Intel Pinetrail platforms.
The tested value of '55' will be filled as the default
pm-qos-value incase the user does not specifies pm-qos value as a
module parameter.
example usage: sudo modprobe ath9k pmqos=65
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the likelihood of false pulse detects in the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM PAPRD rate mask fields only contain mask values for actual
rates in the low 25 bits. The upper bits are reserved for tx power
scale values. Add the proper mask definitions and use them before
writing the values to the register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.
For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing shows that adjusting the slot time based on the coverage class
produces very high latencies and very low throughput on long distance links.
Adjusting only the ACK timeout and leaving the slot time at the regular
values - while technically not optimal for CSMA - works a lot better on
long links (tested with 10 km distance)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(u32) -1 is not particularly useful as a slottime default, so even though
the ath9k_hw default should never get used, it's better to pick something
sane here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have separate callbacks for pre-AR9003 vs AR9003
SREV version checks, so just merge those into one function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a comment about a potential array overrun that needs to
be reviewed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer chips do not need this, and maybe these register writes could have
negative side effects on newer hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless-testing commit 04caf86375
('ath9k: more tx setup cleanups') merged tx path code for HT vs
non-HT frames, however it did not pass the tid pointer to
ath_tx_send_normal, causing an inconsistency between AMPDU vs
non-AMPDU sequence number handling.
Fix this by always passing in the tid pointer for all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when accessing registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers TBTT_TIMER ,DMA_BEACON_ALERT ,NEXT_SWBA are need to be
configured only for AP and IBSS mode.
SWBA register is used for generating software interrupts so that beacon
frames will be created by the software.DMA beacon alert register is
to indicate the hardware to DMA the contents of beacon buffer to PCU buffer
and TBTT to start transmitting the packet buffer to the base band.
Clearly these things are not needed for station/monitor mode so
remove configuring them.
Cc: doug dahlby <ddahlby@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to change interface type
without bringing down the interface.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:
ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
This would make the chip useless upon resume.
I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Suspend requires the device to be in fullsleep otherwise upon
resume the device becomes unresponsive. We need to ensure
that when we want the device to go to sleep it yields to
the request, otherwise we'll have a useless devices upon
resume. Warn when changing the power fails as we need
to look into these issues.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not be idle when we get the ATH9K_INT_TIM_TIMER,
otherwise its a sign of something broken in our design with
our idle state machine and mac80211. Skip these and WARN once
just in case this is triggerable.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can be NULL according to docs, and logging showed it
to be NULL in practice.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The structure struct ieee80211_rx_status *rxs is no longer needed to be
passed to ath_rx_send_to_mac80211 function
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the current save power save implementation we assume a dtim period
of 1.This value is assigned based on a sanity check in the driver
eventhough we had not parsed it from mac80211.This patch obtains the actual
DTIM period from AP by parsing it from mac80211.Yet for handling
multicast traffic we may still have it as fixed rather than parsing it
from mac80211 .This does not breaks power save or anything as the sleep
duration is currently fixed in the driver.This patch may serve to improve
power save in the future by using dtim period for sleep duration and using
correct dtim period adhoc mode.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AUTOSLEEP feature is enabled only for AR9271 and AR9003 version
chipsets.So unlikely macro should be used only to check whether
auto-sleep feature is enabled
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath.ko is a common module shared between ath5k, ar9170usb, ath9k and ath9k_htc.
Adding driver specific data to the shared structure would impact all the
drivers. Handling USB device recognition for devices specific to ath9k_htc
can be handled within the driver itself.
Also, AR7010 refers to the processor used in both AR9280/AR9287 based
devices. Rename the device enumerations accordingly.
While at it, check properly for the bus type when choosing the EEPROM
base address for UB95.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This decreases spammage in the log. A single line message
will still be printed, so users can be aware that problem
exists.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now it is done for only AR9485, will be done for ar9003 also
after proper testing.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also spur channel count and range is different for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper function would be used for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Have it in ah->caps. This will be used during various
calibrations.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 is a single chain and single band (2.4 Ghz) chip.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar9300RateSize is not necessarily a power of 4.
Change ar9003_hw_set_target_power_eeprom
to print the targetPowerValT2 array one per line.
ath9k_hw_ar9300_set_txpower repeated the output 4 times per line,
change it to print the targetPowerValT2 value one per line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.
This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Cc: stable@kernel.org
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invert test and return early.
Move variable declarations to local scope.
Don't initialize variables to 0 unnecessarily.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes debugfs problems when a phy is renamed,
and is able to remove a bit of code that is no longer
needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 916448e77f.
"As far as I can tell, either of these patches breaks multiple VIF
scenarios. I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
-- Ben Greear <greearb@candelatech.com>
http://marc.info/?l=linux-wireless&m=129123368719339&w=2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.
This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent tx path cleanups moved the software retry count tracking
from the ath_buf to the skb cb, however the actual counter update
referred to the wrong location, confusing block-ack window tracking.
Fix this by using the retries counter in the struct ath_frame_info.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 446fad5a5b.
The change had broken the packet injection on monitoring mode.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not ideal to enable btcoex based on subsys id as it is
not unique, they are so random. It is also a pain keeping
all of them in a table to enable btcoex for a particular
hw. Going back to the old idea.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With some upcoming changes we'd like to use
the interface types for P2P capability tests.
Enable them now so that when we add those
tests in wpa_supplicant, nothing will break.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver uses a shared pm_qos_request_list structure for all
devices. This causes the following warning if more than one device is
present in the system:
WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0()
pm_qos_add_request() called for already added request
Modules linked in:
Call Trace:
[<802b1cdc>] dump_stack+0x8/0x34
[<8007dd90>] warn_slowpath_common+0x78/0xa4
[<8007de44>] warn_slowpath_fmt+0x2c/0x38
[<801b0828>] ath9k_init_device+0x5e8/0x6b0
[<801bc508>] ath_pci_probe+0x2dc/0x39c
[<80176254>] pci_device_probe+0x64/0xa4
[<8019471c>] driver_probe_device+0xbc/0x188
[<80194854>] __driver_attach+0x6c/0xa4
[<80193e20>] bus_for_each_dev+0x60/0xb0
[<80193580>] bus_add_driver+0xcc/0x268
[<80194c08>] driver_register+0xe0/0x198
[<801764e0>] __pci_register_driver+0x50/0xe0
[<80365f48>] ath9k_init+0x3c/0x6c
[<8006050c>] do_one_initcall+0xfc/0x1d8
[<80355340>] kernel_init+0xd4/0x174
[<800639a4>] kernel_thread_helper+0x10/0x18
---[ end trace 5345fc6f870564a6 ]---
This patch fixes that warning by using a separate pm_qos_request_list
sructure for each device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller