The Low-Power Clock Gate (LPCG) modules contain a local programming
model to control the clock gates for the peripherals. An LPCG module
is used to locally gate the clocks for the associated peripheral.
And they're bedind the SCU clock.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add imx8qxp clk driver which is based on SCU firmware clock service.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Move the makefile rule higher in the file]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove the dependency between the i.MX8MQ CCM clock driver
and the CONFIG_SOC_IMX8MQ and use CONFIG_CLK_IMX8MQ instead.
CONFIG_CLK_IMX8MQ depends on ARCH_MXC && ARM64.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SCU clock common part which will be used by client clock drivers.
SCU clocks are totally different from the legacy clocks (No much
legacy things can be reused), it's using a firmware interface now based
on SCU protocol. So a new configuration option CONFIG_MXC_CLK_SCU is added.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Mark ccm_ipc_handle static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch introduces CONFIG_MXC_CLK option for legacy MMIO clocks,
this is required to compile legacy MMIO clock conditionally when adding
SCU based clocks for MX8 platforms later.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Fix GXL HDMI Pll fractional bits (from first round)
- Add the Meson8/Meson8b video clocks
- Add clk-input helper and use it for axg-audio clock driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=paYp
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-4.21-2' of https://github.com/BayLibre/clk-meson into clk-meson
Pull more meson clk driver updates from Neil Armstrong:
- Fix GXL HDMI Pll fractional bits (from first round)
- Add the Meson8/Meson8b video clocks
- Add clk-input helper and use it for axg-audio clock driver
* tag 'meson-clk-4.21-2' of https://github.com/BayLibre/clk-meson:
clk: meson: axg-audio: use the clk input helper function
clk: meson: add clk-input helper function
clk: meson: meson8b: add the read-only video clock trees
clk: meson: meson8b: add the fractional divider for vid_pll_dco
clk: meson: meson8b: fix the offset of vid_pll_dco's N value
clk: meson: Fix GXL HDMI PLL fractional bits width
Rework the axg audio clock controller to use the new clk-input helper
function.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed pclk input clock name to axg_audio_pclk]
Link: http://lkml.kernel.org/r/20181204165819.21541-3-jbrunet@baylibre.com
This flag doesn't look to be used by any code, just set in the clk init
structure and then never tested again. Remove it from this driver as it
doesn't provide any benefit. Also remove parenthesis nearby that are not
needed and include clk.h to fix a sparse warning about static function
definition.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag doesn't look to be used by any code, just set in the clk init
structure and then never tested again. Remove it from this drivers as it
doesn't provide any benefit.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag doesn't look to be used by any code, just set in the clk init
structure and then never tested again. Remove it from this driver as it
doesn't provide any benefit.
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag doesn't look to be used by any code, just set in various clk
init structures and then never tested again. Remove it from these
drivers as it doesn't provide any benefit.
Cc: Jiancheng Xue <xuejiancheng@hisilicon.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag doesn't look to be used by any code, just set in various clk
init structures and then never tested again. Remove it from these
drivers as it doesn't provide any benefit.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: <uclinux-h8-devel@lists.sourceforge.jp>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag doesn't look to be used by any code, just set in various clk
init structures and then never tested again. Remove it from these
drivers as it doesn't provide any benefit.
Cc: Anders Berg <anders.berg@lsi.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag doesn't look to be used by any code, just set in various clk
init structures and then never tested again. Remove it from these
drivers as it doesn't provide any benefit.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag doesn't look to be used by any code, just set in various clk
init structures and then never tested again. Remove it from these
drivers as it doesn't provide any benefit.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <linux-renesas-soc@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ROHM bd71837 and bd71847 contain 32768Hz clock gate. Support the clock
using generic clock framework. Note, only bd71837 is tested but bd71847
should be identical what comes to clk parts.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We duplicate the 'depends on' in almost every Kconfig here, and it's
getting out of hand now that we have tens of options for various SoC
drivers here. Let's clean it up a little by making a menuconfig for a
submenu and adding an if wrapper around the driver section.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ENET PLL is different from the other i.MX6 PLLs, as it has
multiple outputs with different post-dividers, which are all
bypassed if the single bypass bit is activated. The hardware setup
looks something like this:
_
refclk-o---PLL---o----DIV1-----| \
| | |M |----OUT1
o-----------------------|_/
| | _
| o----DIV2-----| \
| | |M |----OUT2
o-----------------------|_/
| | _
| `----DIV3-----| \
| |M |----OUT3
`-----------------------|_/
The bypass bit not only bypasses the PLL, but also the attached
post-dividers. This would be reasonbly straight forward to model
with a single output, or with different bypass bits for each output,
but sadly the HW guys decided that it would be good to actuate all
3 muxes with a single bit.
So the need to have the PLL bypassed for one of the outputs always
affects 2 other (in our model) independent branches of the clock
tree.
This means the decision to bypass this PLL is a system wide design
choice and should not be changed on-the-fly, so we can treat any
bapass configuration as static. As such we can just register the
post-dividiers with a ratio that reflects the bypass status, which
allows us to bypass the PLL without breaking our abstraction model
and with it DT stability.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When specifying external clock inputs to the CCM the current code
requires the clocks to be in a "clocks" child node of the DT root.
This is not really conformant with DT best practices.
To avoid the need to deviate from those best practices, allow the
clock inputs to be specified via standard clock handles. This is
in line with how drivers of the later CCM driver revisions on
newer i.MX SoCs handle this.
As we can't retroactively change the DT binding, allow this as an
option with a fallback to the old way of how this has been handled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The exclusive gates may be set up in the wrong way by software running
before the clock driver comes up. In that case the exclusive setup is
locked in its initial state, as the complementary function can't be
activated without disabling the initial setup first.
To avoid this lock situation, reset the exclusive gates to the off
state and allow the kernel to provide the proper setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On i.MX6QP/i.MX6Q/i.MX6DL, there are DCIC1/DCIC2 clocks
gate in CCM_CCGR0 register, add them into clock tree for
clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Same as other i.MX6 SoCs, ensure unused MMDC channel's
handshake is bypassed, this is to make sure no request
signal will be generated when periphe_clk_sel is changed
or SRC warm reset is triggered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Cedrus driver wants to set VE clock higher than it's possible without
changing parent rate.
Allow changing parent rate for VE clock, so clock rate can be set
freely.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The initialization of ret is redundant as it is being re-assigned to
the return value from the call to imx8m_clk_composite_compute_dividers.
Clean this up by removing the initialization.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On H3 (ES1.x, ES2.0) and M3-W (ES1.0, ES1.1) the clock setting for HS400
needs a quirk to function properly. The reason for the quirk is that
there are two settings which produces same divider value for the SDn
clock. On the effected boards the one currently selected results in
HS400 not working.
This change uses the same method as the Gen2 CPG driver and simply
ignores the first clock setting as this is the offending one when
selecting the settings. Which of the two possible settings is used have
no effect for SDR104.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document the known use cases of the different clock settings. This is
useful as different SoC and ES versions use different settings to do
the same thing as there is more than one combination to achieve the
same SDn clock speed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The driver tries to figure out which state a SD clock is in when the
clock is registered, instead of setting a known state. This can be
problematic for two reasons.
1. If the clock driver can't figure out the state of the clock,
registration of the clock fails, and setting of a known state by a
clock user is not possible.
2. The state of the clock depends on if and how the bootloader
configured it. The driver only checks that the rate is known, not if
the clock is stopped or not for example.
Fix this by setting a known state and making sure the clock is stopped.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clkref clocks for usb3, hdmi, ufs, pcie, and usb2. They are all
sourced off CXO_IN, so parent them off "xo" until a proper link to the
rpmcc can be described in DT.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Drop the halt check of the UFS symbol clocks, in accordance with other
platforms. This makes clk_disable_unused() happy and makes it possible
to turn the clocks on again without an error.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Disabling gcc_hmss_dvm_bus_clk and gcc_lpass_at_clk causes the board to
lock up, and by that preventing the kernel to boot without
clk_ignore_unused.
gcc_hmss_dvm_bus_clk is marked always-on downstream, but not referenced,
and gcc_lpass_at_clk isn't mentioned. So let's remove them until they
are needed by some client.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The current list of defined resets is incomplete compared to what the
hardware implements. Enumerate the remaining resets according to the
hardware documentation.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We have this dummy factor clk in place to workaround a missing rpm clk
driver that can manage the XO clk state. Add it in to match what we do
on msm8996.
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PCIe function doesn't work as the clock tree of MAC layer is wrong.
Hence fix the clock table.
Fixes: 3b5e748615 ("clk: mediatek: add clock support for MT7629 SoC")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
use devm variant for of_provider registration.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
[sboyd@kernel.org: Drop unused parent pointer]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
use devm variant for of_provider registration so provider is freed
at exit.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Simplify clean-up for rk808 by using managed version of of_provider
registration.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
use devm variant for of_provider registration so provider is freed
at exit.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It seems to be usual for MFD devices that the created 'clock sub-device'
do not have own DT node. The clock provider information is usually in the
main device node which is owned by the MFD device. Change the devm variant
of clk of-provider registration to check the parent device node if given
device has no own node or if the node does not contain the #clock-cells
property. In such case use the parent node if it contains the #clock-cells.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
[sboyd@kernel.org: Add some comment in the code and pull out logic into
a single function to return the provider device_node pointer]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.
Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The audio blocks require specific clock rates. Until now we were using
the closest clock rate possible with integer N-M factors. This resulted
in audio playback being slightly slower than it should be.
The vendor kernel gets around this (for newer SoCs) by using sigma-delta
modulation to generate a fractional-N factor. As the PLL hardware is
identical in most chips, we can back port the settings from the newer
SoC, in this case the H3, onto the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the clock input helper function. Several amlogic clock controllers
will now be registering bypass clock input. Instead of copying this
code in every of them, let's make an helper function for it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed up to apply on Makefile and clkc.h]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181204165819.21541-2-jbrunet@baylibre.com
Document the devm_of_clk_del_provider and the
devm_of_clk_add_hw_provider functions.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
[sboyd@kernel.org: Comply with kernel-doc formatting]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The R-Car Gen3 HardWare Manual Errata for Rev. 0.80 (Feb 28, 2018) added
the CPEX clock on R-Car D3. This clock can be selected as a clock
source for CMT1 (Compare Match Timer Type 1).
Add the missing clock to the DT bindings header, and implement support
for it in the clock driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
The R-Car Gen3 HardWare Manual Errata for Rev. 0.80 (Dec 22, 2017, and
Feb 28, 2018) removed the SSPSRC, SSP1, and SSP2 clocks on R-Car D3, as
this SoC does not have a Stream and Security Processor.
As these definitions were never used, they can just be removed.
The freed slots in the DT bindings header must not be reused, though.
Fixes: 714c53aa2e ("clk: renesas: Add r8a77995 CPG Core Clock Definitions")
Fixes: d71e851d82 ("clk: renesas: cpg-mssr: Add R8A77995 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
R-Car Gen3 Hardware Manual Errata for Rev 0.80 of February 28, 2018,
removed the module clocks for the Video Input Module (VIN) channels 5-7
on R-Car D3, as they do not exist on this SoC.
Fixes: d71e851d82 ("clk: renesas: cpg-mssr: Add R8A77995 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
According to the R-Car Gen3 Hardware Manual Rev 1.00, the parent clock
of the DU module clocks on R-Car D3 is S1D1.
Fixes: d71e851d82 ("clk: renesas: cpg-mssr: Add R8A77995 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
According to the R-Car Gen3 Hardware Manual Rev 1.00, the parent clock
of the DU module clocks on R-Car E3 is S1D1.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 3570a2af47 ("clk: renesas: cpg-mssr: Add support for R-Car E3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Implement support for the CPEX clock on R-Car V3M. This clock can be
selected as a clock source for CMT1 (Compare Match Timer Type 1).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Implement support for the CPEX clock on R-Car M3-N. This clock can be
selected as a clock source for CMT1 (Compare Match Timer Type 1).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Implement support for the CPEX clock on R-Car M3-W. This clock can be
selected as a clock source for CMT1 (Compare Match Timer Type 1).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Implement support for the CPEX clock on R-Car H3. This clock can be
selected as a clock source for CMT1 (Compare Match Timer Type 1).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Implement support for the CPEX clock on RZ/G2M. This clock can be
selected as a clock source for CMT1 (Compare Match Timer Type 1).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Cedrus driver wants to set VE clock higher than it's possible without
changing parent rate.
In order to correct that, allow changing parent rate for VE clock.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The suniv F1C100s SoC (the chip in some new F-series products of
Allwinner)
has a CCU which seems to be a stripped version of the CCU in SoCs after
sun6i.
Add support for the CCU.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
These are missing 'static' so sparse complains:
drivers/clk/meson/vid-pll-div.c:58:26: warning: symbol '_get_table_val' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1585:12: warning: symbol 'gxbb_vid_pll_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1620:12: warning: symbol 'gxbb_vclk_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1980:12: warning: symbol 'gxbb_cts_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:2036:12: warning: symbol 'gxbb_cts_hdmi_tx_parent_names' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7ULP Clock functions are under joint control of the System
Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
modules, and Core Mode Controller (CMC)1 blocks
The clocking scheme provides clear separation between M4 domain
and A7 domain. Except for a few clock sources shared between two
domains, such as the System Oscillator clock, the Slow IRC (SIRC),
and and the Fast IRC clock (FIRCLK), clock sources and clock
management are separated and contained within each domain.
M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
This driver only adds clock support in A7 domain.
Note that most clocks required to be operated when gated, e.g. pll,
pfd, pcc. And more special cases that scs/ddr/nic mux selecting
different clock source requires that clock to be enabled first,
then we need set CLK_OPS_PARENT_ENABLE flag for them properly.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock providers are recommended to use the new struct clk_hw based API,
so implement IMX clk_hw based provider helpers functions to the new
approach.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the commit 2893c37946 ("clk: make strings in parent name arrays
const"), let's make the parent strings const, otherwise we may meet
the following warning when compiling:
drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
^
In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
of type 'const char * const*'
...
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The imx composite clk is designed for Peripheral Clock Control (PCC)
module observed in IMX ULP SoC series.
NOTE pcc can only be operated when clk is gated.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pfdv2 is designed for PLL Fractional Divide (PFD) observed in System
Clock Generation (SCG) module in IMX ULP SoC series. e.g. i.MX7ULP.
NOTE pfdv2 can only be operated when clk is gated.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pllv4 is designed for System Clock Generation (SCG) module observed
in IMX ULP SoC series. e.g. i.MX7ULP.
The SCG modules generates clock used to derive processor, system,
peripheral bus and external memory interface clocks while this patch
intends to support the PLL part.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Adding CLK_FRAC_DIVIDER_ZERO_BASED flag to indicate the numerator and
denominator value in register are start from 0.
This can be used to support frac dividers like below:
Divider output clock = Divider input clock x [(frac +1) / (div +1)]
where frac/div in register is:
000b - Divide by 1.
001b - Divide by 2.
010b - Divide by 3.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For dividers with zero indicating clock is disabled, instead of giving a
warning each time like "clkx: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not
set" in exist code, we'd like to introduce enable/disable function for it.
e.g.
000b - Clock disabled
001b - Divide by 1
010b - Divide by 2
...
Set rate when the clk is disabled will cache the rate request and only
when the clk is enabled will the driver actually program the hardware to
have the requested divider value. Similarly, when the clk is disabled we'll
write a 0 there, but when the clk is enabled we'll restore whatever rate
(divider) was chosen last.
It does mean that recalc rate will be sort of odd, because when the clk is
off it will return 0, and when the clk is on it will return the right rate.
So to make things work, we'll need to return the cached rate in recalc rate
when the clk is off and read the hardware when the clk is on.
NOTE for the default off divider, the recalc rate will still return 0 as
there's still no proper preset rate. Enable such divider will give user
a reminder error message.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The SCCG is a new PLL type introduced on i.MX8.
The description of this SCCG clock can be found here:
https://www.nxp.com/docs/en/reference-manual/IMX8MDQLQRM.pdf#page=834
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is a new fractional clock type introduced on i.MX8.
The description of this fractional clock can be found here:
https://www.nxp.com/docs/en/reference-manual/IMX8MDQLQRM.pdf#page=834
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add driver for the Clock Control Module found on i.MX8MQ.
Signed-off-by: Anson Huang <anson.huang@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since a lot of clocks on imx8m are formed by a mux, gate, predivider and
divider, the idea here is to combine all of those into one composite clock,
but we need to deal with both predivider and divider at the same time and
therefore we add the imx8m_clk_composite_divider_ops and register
the composite clock with those.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The offsets for the defined BCR reset registers does not match the hardware
documentation. Update the values to match the hardware documentation.
Fixes: b5f5f525c5 (clk: qcom: Add MSM8998 Global Clock Control (GCC) driver)
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The > comparison should be >= to prevent reading beyond the end of the
clock[] array.
(The clock[] array is allocated in zynqmp_clk_setup() and has
clock_max_idx elements.)
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The > comparison should be >= or we write one element beyond the end of
the unit->clk_table[] array.
(The unit->clk_table[] array is allocated in the mmp_clk_init() function
and it has unit->nr_clks elements).
Fixes: 4661fda10f ("clk: mmp: add basic support functions for DT support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These > comparisons should be >= to prevent reading beyond the end of
of the clk_data->hws[] buffer.
The clk_data->hws[] array is allocated in cp110_syscon_common_probe()
when we do:
cp110_clk_data = devm_kzalloc(dev, sizeof(*cp110_clk_data) +
sizeof(struct clk_hw *) * CP110_CLK_NUM,
GFP_KERNEL);
As you can see, it has CP110_CLK_NUM elements which is equivalent to
CP110_MAX_CORE_CLOCKS + CP110_MAX_GATABLE_CLOCKS.
Fixes: d3da3eaef7 ("clk: mvebu: new driver for Armada CP110 system controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the lpass clock controller found on SDM845 based devices.
This would allow lpass peripheral loader drivers to control the clocks to
bring the subsystem out of reset.
LPASS clocks present on the global clock controller would be registered
with the clock framework based on the protected-clock flag. Also do not
gate these clocks if they are left unused, as the lpass clocks require
the global clock controller lpass clocks to be enabled before they are
accessed. Mark the GCC lpass clocks as CRITICAL, for the LPASS clock
access.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The third parent of CSI_MCLK is PLL_PERIPH1, not PLL_PERIPH0.
Fix it.
Fixes: 0577e4853b ("clk: sunxi-ng: Add H3 clocks")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add all clocks to give us the final video clocks within the Meson8,
Meson8b and Meson8m2 SoCs. The final video clocks are:
- cts_enct
- cts_encl
- cts_encp
- cts_enci
- cts_vdac0
- hdmi_tx_pixel
- hdmi_sys
Add multiple clocks in between which are needed to implement these
clocks:
- Opposed to GXBB there is no pre-multiplier for the PLL input. The
assumption here is that the multiplier is required to achieve the HDMI
2.0 clock rates (which are up to twice the rate of the HDMI 1.4
rates).
- The main PLL is called "HDMI PLL" or "HPLL" in the datasheet. Rename
our existing "vid_pll_dco" to "hdmi_pll_dco". The actual VID_PLL clock
also exists further down the tree.
- Rename the existing "vid_pll" clock (which is the OD divider at
HHI_VID_PLL_CNTL[17:16]) to "hdmi_pll_lvds_out" to match the naming
from the datasheet.
- Add the second OD divider called "hdmi_pll_hdmi_out" at
HHI_VID_PLL_CNTL[19:18].
- Add the "vid_pll_in_sel" which can choose between "hdmi_pll_dco" and
another parent. However, the second parent is not use on Amlogic's
3.10 kernel for HDMI or CVBS output so just leave a TODO in the code.
- Add the "vid_pll_in_en" which is located after "vid_pll_in_sel"
according to the datasheet.
- Add "vid_pll_pre_div" which is used for divide-by-5 and divide-by-6 in
Amlogic's 3.10 kernel sources.
- Add "vid_pll_post_div" which divides the output of "vid_pll_pre_div"
further down. The Amlogic 3.10 kernel configures this as divide-by-2
with "vid_pll_pre_div" being configured as divide-by-5 to achieve a
total divider of 10.
- Add the real "vid_pll" clock which selects between "vid_pll_pre_div",
"vid_pll_post_div" and a third "vid_pll_pre_div_mult7_div2" (which is
"vid_pll_pre_div" divided by 3.5). The latter is not supported yet
because it's not used in Amlogic's 3.10 kernel. The "vid_pll" clock
rate can also be measured by clkmsr to check whether this
implementation is correct.
- Add "vid_pll_final_div" which is a post-divider for "vid_pll" and it's
used as input for "vclk" and "vclk2"
- Add the two symmetric "vclk" and "vclk" clock trees, each with a
divide-by-1, divide-by-2, divide-by-4, divide-by-6 and divide-by-12
clock and a divider for each clock.
- Add the "cts_enct", "cts_encp" and "hdmi_tx_pixel" clocks which each
have their own gate and can select between any of the five "vclk"
dividers.
- Add the "cts_encl" and "cts_vdac0" clocks which each have their own
gate and can select between any of the five "vclk2" dividers.
The "hdmi_sys" clock is a different than these video clocks. It takes
"xtal" as input (there are three more but unknown parents). Add this
clock as well as it's used by the HDMI controller. Amlogic's 3.10 kernel
always configures this as "xtal divided by 1", so we can ignore the
other parents for now.
This was tested on Meson8b and Meson8m2 boards by comparing the common
clock framework output with the clock measurer output. The following
video modes were first set in u-boot (by running "video dev open $mode")
before booting Linux:
4K2K30HZ (only supported by Meson8m2, not tested on Meson8b):
- vid_pll: 297000000Hz
- cts_encp: 297000000Hz
- hdmi_tx_pixel: 297000000Hz
1080P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 148500000Hz
720P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 74250000Hz
480P:
- vid_pll: 216000000Hz
- cts_encp: 54000000Hz
- hdmi_tx_pixel: 27000000Hz
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181202214220.7715-4-martin.blumenstingl@googlemail.com
This "vid_pll_dco" (which should be named HDMI_PLL or - as the datasheet
calls it - HPLL) has a 12-bit wide fractional parameter at
HHI_VID_PLL_CNTL2[11:0]. Add this so we correctly calculate the rate of
this PLL when u-boot is configured for a video mode which uses this
fractional parameter.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181202214220.7715-3-martin.blumenstingl@googlemail.com
Unlike the other PLLs on Meson8b the N value "vid_pll_dco" (a better
name would be hdmi_pll_dco or - as the datasheet calls it - HPLL) is
located at HHI_VID_PLL_CNTL[14:10] instead of [13:9].
This results in an incorrect calculation of the rate of this PLL because
the value seen by the kernel is double the actual N (divider) value.
Update the offset of the N value to fix the calculation of the PLL rate.
Fixes: 28b9fcd016 ("clk: meson8b: Add support for Meson8b clocks")
Reported-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181202214220.7715-2-martin.blumenstingl@googlemail.com
Add SPI friendly clock rates to the spi freq table.
Today it's not possible to use SPI at lower than 960Khz.
This patch adds 100/250/500/1000 kHz configs to the table.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This function is called from driver probe, which isn't the same as
__init code because driver probe can happen later. Drop the __init
marking here to fix this potential problem.
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Wenzhen Yu <wenzhen.yu@mediatek.com>
Cc: Weiyi Lu <weiyi.lu@mediatek.com>
Fixes: 2fc0a509e4 ("clk: mediatek: add clock support for MT7622 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This function is used from more places than just __init code. Removing
__init silences a section mismatch warning here.
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Wenzhen Yu <wenzhen.yu@mediatek.com>
Cc: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no need to have the 'struct clk_hw **hws' variable static
since new value always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add all supported clocks exported from every susbystem found on MT7629 SoC.
Signed-off-by: Wenzhen Yu <wenzhen.yu@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On the R40, in addition to a mux between the RTC's own RC oscillator and
an external 32768 Hz crystal, which are muxed inside the RTC module, the
CCU also has its own RC oscillator, which runs at around 2 MHz, and can
be muxed with the LOSC output from the RTC. This muxed output is called
"SYS 32K" in the module clock diagram, but otherwise referred to as the
LOSC throughout the CCU documentation.
The RC oscillator is not very accurate, even though it has an undocumented
calibration function. We really want a precise clock at 32768 Hz,
instead of something at around 32 KHz. This patch forces the SYS 32K
clock to use the RTC output as its parent, and doesn't bother
registering the internal oscillator nor a clock mux.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This is only used in this file, so mark it static to silence a sparse
warning.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
[sboyd@kernel.org: Rename show function to keep compiling]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In an earlier version of commit 453361cdd7 ("clk: qcom: Add graphics
clock controller driver for SDM845") there were 6 listed parents for
"gpu_cc_gmu_clk_src". In the version that landed there were 5.
...but "num_parents" was still left at 6. On my system this goes boom
at bootup.
Fixes: 453361cdd7 ("clk: qcom: Add graphics clock controller driver for SDM845")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Most of the time the CPU should not be touching the GX
domain on the GPU except for a very special use case when
the CPU needs to force the GX headswitch off. Add a
dummy enable function for the GX gdsc to simulate success
so that the pm_runtime reference counting is correct.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In extreme cases an individual gdsc may wish to override the
power domain enable or disable callback functions for their own
purposes. Only set the generic gdsc callback if the function pointers
are not already set.
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the graphics clock controller found on SDM845
based devices. This would allow graphics drivers to probe and
control their clocks.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Collapse return in probe into less lines]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The GXL Documentation specifies 12 bits for the Fractional bit field,
bit the last bits have a different purpose that we cannot handle right
now, so update the bitwidth to have correct fractional calculations.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added comment on GXL HHI_HDMI_PLL_CNTL register shift]
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lkml.kernel.org/r/20181121111922.1277-1-narmstrong@baylibre.com
Add the newly added clock-id for PCLK_ACODECPHY to the gate-clock,
so that it gets usable from devicetree.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The audio blocks require specific clock rates. Until now we were using
the closest clock rate possible with integer N-M factors. This resulted
in audio playback being slightly slower than it should be.
The vendor kernel gets around this (for some SoCs) by using sigma-delta
modulation to generate a fractional-N factor. As the PLL hardware is
identical in most chips, we can port the settings for H3 onto the A64.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
There are four CPU clock post dividers:
- ABP
- PERIPH (used for the ARM global timer and ARM TWD timer)
- AXI
- L2 DRAM
Each of these clocks consists of two clocks:
- a mux to select between "cpu_clk" divided by 2, 3, 4, 5, 6, 7 or 8
- a "_clk_dis" gate. The public S805 datasheet states that this should
be set to 1 to disable the clock, the default value is 0. There is
also a hint that these are "just in case" bits which only exist in
case the corresponding mux implementation does not allow glitch-free
parent changes (the muxes are designed in a way that the clock can
stay enabled when changing the mux). It's still good practise to
describe this clock even if we're not supposed to modify it. Thus
this uses the read-only gate ops.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181122214017.25643-5-martin.blumenstingl@googlemail.com
The "cpu_div2" and "cpu_div3" take "cpu_in" as input and divide that by
2 or 3. The clock controller can also generate various CPU clock
post-dividers (2, 3, 4, 5, 6, 7, 8) which are derived from "cpu_clk".
When adding support for these post-dividers our clock naming could be
misleading as we have "cpu_div2" as well as "cpu_clk_div2".
Rename the existing "cpu_in" dividers so the name of the divider's
parent is part of the divider clock's name.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181122214017.25643-4-martin.blumenstingl@googlemail.com
Some of the gate clocks are described as "just in case" bits in the
datasheet. Examples are the ABP, PERIPH, AXI and L2 DRAM clocks on
Meson8b.
The datasheet suggests that these bits are not touched. The full
explanation is:
"Set to 1 to manually disable the [...] clock when changing the mux
selection. Typically this bit is set to 0 since the clock muxes can
switch without glitches.".
This adds new read-only ops for gate clocks so we can describe these
clocks in our clock controller drivers while ensuring that we can't
accidentally modify the registers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181122214017.25643-3-martin.blumenstingl@googlemail.com
Currently all clocks in the CPU clock tree are marked as read-only
(using the corresponding _ro_ clk_ops). This was correct since changing
the clock tree could cause the system to lock up.
Switch all clocks to their corresponding clk_ops variant which is not
read-only to allow changing the CPU clock tree since the bug which
locked up the system is now fixed (by switching the CPU clock temporary
to run off XTAL while changing the CPU clock tree).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-7-martin.blumenstingl@googlemail.com
Changing the CPU clock requires changing various clocks including the
SYS PLL. The existing meson clk-pll and clk-regmap drivers can change
all of the relevant clocks already.
However, changing for exampe the SYS PLL is problematic because as long
as the CPU is running off a clock derived from SYS PLL changing the
latter results in a full system lockup.
Fix this system lockup by switching the CPU clock to run off the XTAL
while we are changing the any of the clocks in the CPU clock tree.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-6-martin.blumenstingl@googlemail.com
The sys_pll on the EC-100 board is configured to 1584MHz at boot
(either by u-boot, firmware or chip defaults). This is achieved by using
M = 66, N = 1 (24MHz * 66 / 1).
At boot the CPU clock is running off sys_pll divided by 2 which results
in 792MHz. Thus M = 66 is considered to be a "safe" value for Meson8b.
To achieve 1608MHz (one of the CPU OPPs on Meson8 and Meson8m2) we need
M = 67, N = 1. I ran "stress --cpu 4" while infinitely cycling through
all available frequencies on my Meson8m2 board and could not spot any
issues with this setting (after ~12 hours of running this).
On Meson8, Meson8b and Meson8m2 we also want to be able to use 408MHz
and 816MHz CPU frequencies. These can be achieved by dividing sys_pll by
4 (for 408MHz) or 2 (for 816MHz). That means that sys_pll has to run at
1632MHz which can be generated using M = 68, N = 1.
Similarily we also want to be able to use 1008MHz as CPU frequency. This
means that sys_pll has to run either at 1008MHz or 2016MHz. The former
would result in an M value of 42, which is lower than the smallest value
used by the 3.10 GPL kernel sources from Amlogic (50 is the lower limit
there). Thus we need to run sys_pll at 2016MHz which can ge generated
using M = 84, N = 1.
I tested M = 68 and M = 84 on my Meson8b Odroid-C1 and my Meson8m2 board
by running "stress --cpu 4" while infinitely cycling thorugh all
available frequencies. I could not spot any issues after ~12 hours of
running this.
Amlogic's 3.10 GPL kernel sources have more M/N combinations. I did not
add them yet because M = 74 (to achieve close to 1800MHz on Meson8) and
M = 82 (to achieve close to 1992MHz on Meson8 as well) caused my
Meson8m2 board to hang randomly. It's not clear why this is (for example
because the board's voltage regulator design is bad, some missing bits
for these values in our clk-pll driver, etc.). Thus the following M
values from the Amlogic 3.10 GPL kernel sources are skipped as of now:
69, 70, 71, 72, 73, 74, 76, 78, 80, 82, 84, 86, 88, 90, 92, 94, 96, 98
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-5-martin.blumenstingl@googlemail.com
We don't want the common clock framework to disable the "cpu_clk" if
it's not used by any device. The cpufreq-dt driver does not enable the
CPU clocks. However, even if it would we would still want the CPU clock
to be enabled at all times because the CPU clock is also required even
if we disable CPU frequency scaling on a specific board.
The reason why we want the CPU clock to be enabled is a clock further up
in the tree:
Since commit 6f888e7bc7bd58 ("clk: meson: clk-pll: add enable bit") the
sys_pll can be disabled. However, since the CPU clock is derived from
sys_pll we don't want sys_pll to get disabled. The common clock
framework takes care of that for us by enabling all parent clocks of our
CPU clock when we mark the CPU clock with CLK_IS_CRITICAL.
Until now this is not a problem yet because all clocks in the CPU
clock's tree (including sys_pll) are read-only. However, once we allow
modifications to the clocks in that tree we will need this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-4-martin.blumenstingl@googlemail.com
The cpu_div3 clock (cpu_in divided by 3) generates a signal with a duty
cycle of 33%. The CPU clock however requires a clock signal with a duty
cycle of 50% to run stable.
cpu_div3 was observed to be problematic when cycling through all
available CPU frequencies (with additional patches on top of this one)
while running "stress --cpu 4" in the background. This caused sporadic
hangs where the whole system would fully lock up.
Amlogic's 3.10 kernel code also does not use the cpu_div3 clock either
when changing the CPU clock.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-3-martin.blumenstingl@googlemail.com
Since commit 6f888e7bc7bd58 ("clk: meson: clk-pll: add enable bit") our
PLLs also support the "enable" bit. Currently meson_clk_pll_enable
unconditionally resets the PLL, enables it, takes it out of reset and
waits until it is locked.
This works fine for our current clock trees. However, there will be a
problem once we allow modifications to sys_pll on Meson8, Meson8b and
Meson8m2 (which will be required for CPU frequency scaling):
the CPU clock is derived from the sys_pll clock. Once clk_enable is
called on the CPU clock this will be propagated by the common clock
framework up until the sys_pll clock. If we reset the PLL
unconditionally in meson_clk_pll_enable the CPU will be stopped (on
Meson8, Meson8b and Meson8m2).
To prevent this we simply check if the PLL is already enabled and do
reset the PLL if it's already enabled and locked.
Now that we have a utility function to check whether the PLL is enabled
we can also pass that to our clk_ops to let the common clock framework
know about the status of the hardware clock.
For now this is of limited use since the only common clock framework's
internal "disabled unused clocks" mechanism checks for this. Everything
else still uses the ref-counting (internal to the common clock
framework) when clk_enable is called.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-2-martin.blumenstingl@googlemail.com
According to the public S805 datasheet HHI_SYS_CPU_CLK_CNTL1[29:20] is
the register for the CPU scale_div clock. This matches the code in
Amlogic's 3.10 GPL kernel sources:
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
This means that the divider register is 10 bit wide instead of 9 bits.
So far this is not a problem since all u-boot versions I have seen are
not using the cpu_scale_div clock at all (instead they are configuring
the CPU clock to run off cpu_in_sel directly).
The fixes tag points to the latest rework of the CPU clocks. However,
even before the rework it was wrong. Commit 7a29a86943 ("clk: meson:
Add support for Meson clock controller") defines MESON_N_WIDTH as 9 (in
drivers/clk/meson/clk-cpu.c). But since the old clk-cpu implementation
this only carries the fixes tag for the CPU clock rewordk.
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-3-martin.blumenstingl@googlemail.com
The public S805 datasheet only mentions that
HHI_SYS_CPU_CLK_CNTL1[20:29] contains a divider called "cpu_scale_div".
Unfortunately it does not mention how to use the register contents.
The Amlogic 3.10 GPL kernel sources are using the following code to
calculate the CPU clock based on that register (taken from
arch/arm/mach-meson8/clock.c in the 3.10 Amlogic kernel, shortened to
make it easier to read):
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
if (sel == 3) /* use cpu_scale_div */
div = 2 * N;
else
div = ... /* not relevant for this example */
cpu_clk = parent_clk / div;
This suggests that the formula is: parent_rate / 2 * register_value
However, running perf (which can measure the CPU clock rate thanks to
the ARM PMU) shows that this formula is not correct.
This can be reproduced with the following steps:
1. boot into u-boot
2. let the CPU clock run off the XTAL clock:
mw.l 0xC110419C 0x30 1
3. set the cpu_scale_div register:
to value 0x1: mw.l 0xC110415C 0x801016A2 1
to value 0x2: mw.l 0xC110415C 0x802016A2 1
to value 0x5: mw.l 0xC110415C 0x805016A2 1
4. let the CPU clock run off cpu_scale_div:
mw.l 0xC110419C 0xbd 1
5. boot Linux
6. run: perf stat -aB stress --cpu 4 --timeout 10
7. check the "cycles" value
I get the following results depending on the cpu_scale_div value:
- (cpu_in_sel - this is the input clock for cpu_scale_div - runs at
1.2GHz)
- 0x1 = 300MHz
- 0x2 = 200MHz
- 0x5 = 100MHz
This means that the actual formula to calculate the output of the
cpu_scale_div clock is: parent_rate / 2 * (register value + 1).
The register value 0x0 is reserved. When letting the CPU clock run off
the cpu_scale_div while the value is 0x0 the whole board hangs (even in
u-boot).
I also verified this with the TWD timer: when adding this to the .dts
without specifying it's clock it will auto-detect the PERIPH (which is
the input clock of the TWD) clock rate (and the result is shown in the
kernel log). On Meson8, Meson8b and Meson8m2 the PERIPH clock is CPUCLK
divided by 4. This also matched for all three test-cases from above (in
all cases the TWD timer clock rate was approx. one fourth of the CPU
clock rate).
A small note regarding the "fixes" tag: the original issue seems to
exist virtually since forever. Even commit 28b9fcd016 ("clk:
meson8b: Add support for Meson8b clocks") seems to handle this wrong. I
still decided to use commit 251b6fd38b ("clk: meson: rework meson8b
cpu clock") because this is the first commit which gets the CPU hiearchy
correct and thus it's the first commit where the cpu_scale_div register
is used correctly (apart from the bug in the cpu_scale_table).
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-2-martin.blumenstingl@googlemail.com
The clock controller is located in a register range (called "HHI") which
contains more than just registers for the clock controller. Known
consumers of the HHI register range are:
- the clock controller
- a reset controller
- temperature sensor calibration coefficient (TSC) (only on Meson8b and
Meson8m2)
- HDMI controller
The main reason for using a syscon is the "temperature sensor
calibration coefficient" which has to be set for the built-in temperature
sensor to work correctly. Four TSC bits are located in the SAR ADC's
register space. However on Meson8b and Meson8m2 there is a fifth TSC bit
which is unfortunately located in the HHI register space. To be more
precise, bit 9 of the HHI_DPLL_TOP_0 register (which sits right between
the HHI_SYS_PLL and HHI_VID_PLL registers).
Get the regmap from the parent (HHI syscon) node to support all
functionality of the HHI register range. Backwards compatibility with
old .dtbs is ensured by falling back to parsing the registers just like
before this change.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181028120859.5735-3-martin.blumenstingl@googlemail.com
Add the clocks entries used in the video clock path, the clock path
is doubled to permit having different synchronized clocks for different
parts of the video pipeline.
All dividers are flagged with CLK_GET_RATE_NOCACHE, and all gates are flagged
with CLK_IGNORE_UNUSED since they are currently directly handled by the
Meson DRM Driver.
Once the DRM Driver is fully migrated to using the Common Clock Framework
to handle the video clock tree, the CLK_GET_RATE_NOCACHE and CLK_IGNORE_UNUSED
will be dropped.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-5-git-send-email-narmstrong@baylibre.com
In an attempt to better describe the HDMI PLL, a single DCO clock was
left for GXBB and GXL, but the GXL DCO does not have a pre-multiplier.
This patch adds back a GXL specific HDMI PLL DCO with xtal as parent.
Fixes: 87173557d2 ("clk: meson: clk-pll: remove od parameters")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-3-git-send-email-narmstrong@baylibre.com
Add support the VID_PLL fully programmable divider used right after the
HDMI PLL clock source. It is used to achieve complex fractional division
with a programmble bitfield.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-2-git-send-email-narmstrong@baylibre.com
Certain firmware configurations "protect" clks and cause the entire
system to reboot when a non-secure OS such as Linux tries to read or
write protected clk registers. But other firmware configurations allow
reading or writing the same registers, and they may actually require
that the OS use the otherwise locked down clks. Support the
'protected-clocks' property by never registering these protected clks
with the common clk framework. This way, when firmware is protecting
these clks we won't have the chance to ever read or write these
registers and take down the entire system.
Cc: Taniya Das <tdas@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch fixes definition of I2S1 clock gate register for rk3328.
Current setting is not related I2S clocks.
- bit6 of CRU_CLKGATE_CON0 means clk_ddrmon_en
- bit6 of CRU_CLKGATE_CON1 means clk_i2s1_en
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The "security processor", sometimes referred to as "wireless trusted
module" or "generic encrypt unit" is a low-power core present on MMP2,
that has nothing to do with security, wireless, trust or encryption.
On an OLPC machine it runs CForth and serves as a keyboard controller:
http://dev.laptop.org/git/users/wmb/cforth/tree/src/app/arm-xo-1.75/ps2.fth
The register address was obtained from the OLPC kernel, since the
datasheet seems to be the Marvell's most important business secret.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Similar to commit a9f0c0e563 ("clk: rockchip: fix rk3188 sclk_smc
gate data") there is one other gate clock in the rk3188 clock driver
with a similar wrong ordering, the sclk_mac_lbtest. So fix it as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Simon Arlott <simon@arlott.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Return proper error code in case query for fixed factor
parameter fails. This also fixes build warning for set
but not used variable 'ret'.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
DSI DPHY gate bit on MIPI DSI clock register is bit 15
not bit 30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner SoC like SUN8I and SUN50I has DE2 CCU so enable them
as default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Device tree node name are not supposed to have "_" in them so fix the
node name use of xo_board to xo-board
Fixes: 652f1813c1 ("clk: qcom: gcc: Add global clock controller driver for QCS404")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add more chip-specific compatible strings to support more Socs.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Similar to gxbb and gxl platforms, axg SCPI Cortex-M co-processor
uses the fdiv2 and fdiv3 to, among other things, provide the cpu
clock.
Until clock hand-off mechanism makes its way to CCF and the generic
SCPI claims platform specific clocks, these clocks must be marked as
critical to make sure they are never disabled when needed by the
co-processor.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The registered clks should unregister when something wrong happens
before going out in function clk_boston_setup().
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Smatch report warnings:
drivers/clk/imgtec/clk-boston.c:76 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:83 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:90 clk_boston_setup() warn: possible memory leak of 'onecell'
'onecell' is malloced in clk_boston_setup(), but not be freed
before leaving from the error handling cases.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On the Khadas VIM2 (GXM) and LePotato (GXL) board there are problems
with reboot; e.g. a ~60 second delay between issuing reboot and the
board power cycling (and in some OS configurations reboot will fail
and require manual power cycling).
Similar to 'commit c987ac6f1f ("clk:
meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL")' the SCPI Cortex-M4
Co-Processor seems to depend on FCLK_DIV3 being operational.
Until commit 05f814402d ("clk:
meson: add fdiv clock gates"), this clock was modeled and left on by
the bootloader.
We don't have precise documentation about the SCPI Co-Processor and
its clock requirement so we are learning things the hard way.
Marking this clock as critical solves the problem but it should not
be viewed as final solution. Ideally, the SCPI driver should claim
these clocks. We also depends on some clock hand-off mechanism
making its way to CCF, to make sure the clock stays on between its
registration and the SCPI driver probe.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Ensure that direct PLLM sourcing is turned off for EMC as we don't support
that configuration in the clk driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Kernel should never gate the EMC clock as it causes immediate lockup, so
removing clk-gate functionality doesn't affect anything. Turning EMC clk
gate into divider allows to implement glitch-less EMC scaling, avoiding
reparenting to a backup clock.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add rpm smd clocks, PMIC and bus clocks which are required on QCS404
for clients to vote on.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
[bjorn: Dropped cxo, voter clocks and static initialization]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk_ops structure is only stored in the ops fields of
clk_init_data structures. This field is const, so the clk_ops
structure can be const as well.
Identified and transformed using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These clk_ops structures are only passed to a call to
clk_register_composite where the corresponding parameters
are const, so the clk_ops structure can be const as well.
Identified and transformed using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These clk_ops structures are only stored in the ops field of a
clk_init_data structure. This field is const, so the clk_ops
structures can be const as well.
Identified and transformed using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk_ops structure is only stored in the ops field of clk_init_data
structures. This field is const, so the clk_ops structure can be
const as well.
Identified and transformed using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk_ops structure is only stored in the ops field of a
clk_init_data structure. This field is const, so the clk_ops
structure can be const as well.
Identified and transformed using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are clock assignments in all i.MX7D dtb files for UART1,
below is the example in imx7d-sdb.dts, so setting UART1 clock
in clock driver is NOT necessary, actually, module clocks setting
should be done in module driver.
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
status = "okay";
};
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The license text is specifying GPL v2 or later but the MODULE_LICENSE
is set to GPL v2 which means GNU Public License v2 only. So choose the
license text as the correct one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the fixed factor clock is created by devicetree,
of_clk_add_provider is called. Add a call to
of_clk_del_provider in the remove function to balance
it out.
Reported-by: Alan Tull <atull@kernel.org>
Fixes: 971451b3b1 ("clk: fixed-factor: Convert into a module platform driver")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On R-Car V3M (R8A77970), the RPC/RPCD2 clocks are output by the common
divider. Describe them, as well as the RPC-IF module clock.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Support for mixer0, mixer1, writeback and rotation units is added.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Video PLL factors can be set in a way that final PLL rate is outside
stable range. H6 user manual specifically says that N factor should not
be below 12. While it doesn't says anything about maximum stable rate, it
is clear that PLL doesn't work at 6.096 GHz (254 * 24 MHz).
Set minimum allowed PLL video rate to 288 MHz (12 * 24 MHz) and maximum
to 2.4 GHz, which is maximum in BSP driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has multiplier N range between 1 and 254. Since parent
rate is 24MHz, intermediate result when calculating final rate easily
overflows 32 bit variable.
Because of that, introduce function for calculating clock rate which
uses 64 bit variable for intermediate result.
Fixes: 6174a1e24b ("clk: sunxi-ng: Add N-M-factor clock support")
Fixes: ee28648cb2 ("clk: sunxi-ng: Remove the use of rational computations")
CC: <stable@vger.kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently MP clocks don't consider adjusting parent rate even if they
are allowed to do so. Such behaviour considerably lowers amount of
possible rates, which is very inconvenient when such clock is used for
pixel clock, for example.
In order to improve the situation, adjusting parent rate is considered
when allowed.
This code is inspired by clk_divider_bestdiv() function, which does
basically the same thing for different clock type.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
MUX bits for MMC clock register range are 25:24 where 24 is shift
and 2 is width So fix the width number from 3 to 2.
Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
In the user manual of A64 SoC, the bit 22 and 23 of pll-mipi control
register is called "LDO{1,2}_EN", and according to the BSP source code
from Allwinner , the LDOs are enabled during the clock's enabling
process.
The clock failed to generate output if the two LDOs are not enabled.
Add the two bits to the clock's gate bits, so that the LDOs are enabled
when the PLL is enabled.
Fixes: c6a0637460 ("clk: sunxi-ng: Add A64 clocks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
because of summer time holidays/vacations. The biggest change in the diffstat
is in the Qualcomm clk driver, where they got support for CPUs and handful of
SoCs. After that, the at91 driver got a major rewrite for newer DT bindings
that should make things easier going forward and the TI code moved to a
clockdomain based design. The long tail is mostly small driver updates for
newer clks and some simpler SoC clock drivers such as the Hisilicon and imx
support.
In the core framework, we only have two small changes this time. One is a new
clk API to get all clks for a device with the bulk clk APIs. This allows
drivers that don't care about doing anything besides turning on all the clks to
just clk_get() them all and turn them on. The other change is the beginning of
a way to support save and restore of clk settings in the clk framework. TI is
the only user right now, but we will want to expand upon this design in the
future to support more save and restore of clk registers. At least this gets
us started and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes
-----BEGIN PGP SIGNATURE-----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=V5aK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time it looks like a quieter release cycle in the clk tree. I
guess that's because of summer time holidays/vacations. The biggest
change in the diffstat is in the Qualcomm clk driver, where they got
support for CPUs and handful of SoCs. After that, the at91 driver got
a major rewrite for newer DT bindings that should make things easier
going forward and the TI code moved to a clockdomain based design.
The long tail is mostly small driver updates for newer clks and some
simpler SoC clock drivers such as the Hisilicon and imx support.
In the core framework, we only have two small changes this time.
One is a new clk API to get all clks for a device with the bulk clk
APIs. This allows drivers that don't care about doing anything besides
turning on all the clks to just clk_get() them all and turn them on.
The other change is the beginning of a way to support save and restore
of clk settings in the clk framework. TI is the only user right now,
but we will want to expand upon this design in the future to support
more save and restore of clk registers. At least this gets us started
and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (186 commits)
clk: qcom: Remove unused arrays in SDM845 GCC
clk: fixed-rate: fix of_node_get-put imbalance
clk: s2mps11: Add used attribute to s2mps11_dt_match
clk: qcom: gcc-sdm660: Add MODULE_LICENSE
clk: qcom: Add safe switch hook for krait mux clocks
dt-bindings: clock: Document qcom,krait-cc
clk: qcom: Add Krait clock controller driver
dt-bindings: arm: Document qcom,kpss-gcc
clk: qcom: Add KPSS ACC/GCC driver
clk: qcom: Add support for Krait clocks
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add MSM8960/APQ8064's HFPLLs
dt-bindings: clock: Document qcom,hfpll
clk: qcom: Add HFPLL driver
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
ARM: Add Krait L2 register accessor functions
clk: imx6q: add mmdc0 ipg clock
clk: imx6sl: add mmdc ipg clocks
clk: imx6sll: add mmdc1 ipg clock
clk: imx6sx: add mmdc1 ipg clock
...
When a memblock allocation APIs are called with align = 0, the alignment
is implicitly set to SMP_CACHE_BYTES.
Implicit alignment is done deep in the memblock allocator and it can
come as a surprise. Not that such an alignment would be wrong even
when used incorrectly but it is better to be explicit for the sake of
clarity and the prinicple of the least surprise.
Replace all such uses of memblock APIs with the 'align' parameter
explicitly set to SMP_CACHE_BYTES and stop implicit alignment assignment
in the memblock internal allocation functions.
For the case when memblock APIs are used via helper functions, e.g. like
iommu_arena_new_node() in Alpha, the helper functions were detected with
Coccinelle's help and then manually examined and updated where
appropriate.
The direct memblock APIs users were updated using the semantic patch below:
@@
expression size, min_addr, max_addr, nid;
@@
(
|
- memblock_alloc_try_nid_raw(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_raw(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid_nopanic(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_nopanic(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid(size, SMP_CACHE_BYTES, min_addr, max_addr, nid)
|
- memblock_alloc(size, 0)
+ memblock_alloc(size, SMP_CACHE_BYTES)
|
- memblock_alloc_raw(size, 0)
+ memblock_alloc_raw(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from(size, 0, min_addr)
+ memblock_alloc_from(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_nopanic(size, 0)
+ memblock_alloc_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low(size, 0)
+ memblock_alloc_low(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low_nopanic(size, 0)
+ memblock_alloc_low_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from_nopanic(size, 0, min_addr)
+ memblock_alloc_from_nopanic(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_node(size, 0, nid)
+ memblock_alloc_node(size, SMP_CACHE_BYTES, nid)
)
[mhocko@suse.com: changelog update]
[akpm@linux-foundation.org: coding-style fixes]
[rppt@linux.ibm.com: fix missed uses of implicit alignment]
Link: http://lkml.kernel.org/r/20181016133656.GA10925@rapoport-lnx
Link: http://lkml.kernel.org/r/1538687224-17535-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl" interface
that was a little controversial at first, but the version we merged
solved that by not exposing arbitrary firmware calls to user space.
- The Amlogic Meson platform gains a "canvas" driver that is used
for video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for
their respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in particular
a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem"
device driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=c/PQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
- Nvidia Tegra clk driver MBIST workaround fix
- clk_bulk_get_all() API and friends to get all the clks for a device
* clk-tegra:
clk: tegra210: Include size.h for compilation ease
clk: tegra: Fixes for MBIST work around
clk: tegra: probe deferral error reporting
* clk-bulk-get-all:
clk: add managed version of clk_bulk_get_all
clk: add new APIs to operate on all available clocks
clk: bulk: add of_clk_bulk_get()
- Hisilicon 3670 SoC support
* clk-samsung:
dt-bindings: clock: samsung: Add SPDX license identifiers
clk: samsung: Use clk_hw API for calling clk framework from clk notifiers
clk: samsung: exynos5420: Enable PERIS clocks for suspend
clk: samsung: exynos5420: Define CLK_SECKEY gate clock only or Exynos5420
clk: samsung: exynos5433: Keep sclk_uart clocks enabled in suspend
clk: samsung: Remove obsolete code for Exynos4412 ISP clocks
clk: samsung: exynos5433: Add suspend state for TOP, CPIF & PERIC CMUs
clk: samsung: Use NOIRQ stage for Exynos5433 clocks suspend/resume
clk: samsung: exynos5420: Use generic helper for handling suspend/resume
clk: samsung: exynos4: Use generic helper for handling suspend/resume
clk: samsung: Add support for setting registers state before suspend
clk: samsung: exynos5250: Use generic helper for handling suspend/resume
clk: samsung: s5pv210: Use generic helper for handling suspend/resume
clk: samsung: s3c64xx: Use generic helper for handling suspend/resume
clk: samsung: s3c2443: Use generic helper for handling suspend/resume
clk: samsung: s3c2412: Use generic helper for handling suspend/resume
clk: samsung: s3c2410: Use generic helper for handling suspend/resume
clk: samsung: Remove excessive include
* clk-hisi3670:
clk: hisilicon: Add clock driver for Hi3670 SoC
dt-bindings: clk: hisilicon: Add bindings for Hi3670 clk
* clk-at91-div-0:
clk: at91: Fix division by zero in PLL recalc_rate()
* clk-ti:
clk: ti: Prepare for remove of OF node name
clk: Clean up suspend/resume coding style
clk: ti: Add functions to save/restore clk context
clk: clk: Add clk_gate_restore_context function
clk: Add functions to save/restore clock context en-masse
clk: ti: dra7: add new clkctrl data
clk: ti: dra7xx: rename existing clkctrl data as compat data
clk: ti: am43xx: add new clkctrl data for am43xx
clk: ti: am43xx: rename existing clkctrl data as compat data
clk: ti: am33xx: add new clkctrl data for am33xx
clk: ti: am33xx: rename existing clkctrl data as compat data
clk: ti: clkctrl: replace dashes from clkdm name with underscore
clk: ti: clkctrl: support multiple clkctrl nodes under a cm node
dt-bindings: clock: dra7xx: add clkctrl indices for new data layout
dt-bindings: clock: am43xx: add clkctrl indices for new data layout
dt-bindings: clock: am33xx: add clkctrl indices for new data layout
- S2RAM support for Marvell mvebu periph clks
* clk-mvebu-periph-pm:
clk: mvebu: armada-37xx-periph: add suspend/resume support
clk: mvebu: armada-37xx-periph: save the IP base address in the driver data
* clk-meson:
clk: meson: meson8b: use the regmap in the internal reset controller
clk: meson: meson8b: register the clock controller early
clk: meson-axg: pcie: drop the mpll3 clock parent
clk: meson: axg: round audio system master clocks down
clk: meson: clk-pll: drop hard-coded rates from pll tables
clk: meson: clk-pll: remove od parameters
clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary
clk: meson: clk-pll: add enable bit
* clk-allwinner:
dt-bindings: clock: sun50i-a64-ccu: Add PLL_VIDEO0 macro
clk: sunxi-ng: a64: Add max. rate constraint to video PLLs
clk: sunxi-ng: a64: Add minimal rate for video PLLs
clk: sunxi-ng: sun50i: h6: Add 2x fixed post-divider to MMC module clocks
clk: sunxi-ng: a83t: Add max. rate constraint to video PLLs
clk: sunxi-ng: nkmp: Add constraint for maximum rate
clk: sunxi-ng: r40: Add max. rate constraint to video PLLs
clk: sunxi-ng: h3/h5: Add max. rate constraint to pll-video
clk: sunxi-ng: Add maximum rate constraint to NM PLLs
clk: sunxi-ng: h6: fix PWM gate/reset offset
clk: sunxi-ng: h6: fix bus clocks' divider position
* clk-mvebu-dup:
clk: mvebu: ap806: Remove superfluous of_clk_add_provider
* clk-davinci:
clk: davinci: kill davinci_clk_reset_assert/deassert()
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
* clk-dt-name:
clk: Convert to using %pOFn instead of device_node.name
* clk-ti-of-node:
clk: ti: fix OF child-node lookup
* clk-sa:
clk: mvebu: armada-37xx-tbg: Switch to clk_get and balance it in probe
reset: hisilicon: fix potential NULL pointer dereference
clk: cdce925: release child device nodes
clk: qcom: clk-branch: Use true and false for boolean values
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
* clk-spdx:
clk: mvebu: use SPDX-License-Identifier
clk: renesas: Convert to SPDX identifiers
clk: renesas: use SPDX identifier for Renesas drivers
clk: s2mps11,s3c64xx: Add SPDX license identifiers
clk: max77686: Add SPDX license identifiers
* clk-qcom-dfs:
clk: qcom: Allocate space for NULL terimation in DFS table
clk: qcom: gcc: Register QUPv3 RCGs for DFS on SDM845
clk: qcom: Add support for RCG to register for DFS
* clk-smp2s11-include:
clk: s2mps11: Use existing defines from bindings for clock IDs
* clk-qcom-8996-missing:
clk: qcom: Add some missing gcc clks for msm8996
* clk-qcom-qspi:
clk: qcom: Add qspi (Quad SPI) clocks for sdm845
clk: qcom: Add qspi (Quad SPI) clock defines for sdm845 to header
This change removes a parent map and parent name array that
appear to be completely unreferenced.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the fixed rate clock is created by devicetree,
of_clk_add_provider is called. Add a call to
of_clk_del_provider in the remove function to balance
it out.
Signed-off-by: Alan Tull <atull@kernel.org>
Fixes: 435779fe13 ("clk: fixed-rate: Convert into a module platform driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clang warns after commit 8985167ecf ("clk: s2mps11: Fix matching when
built as module and DT node contains compatible"):
drivers/clk/clk-s2mps11.c:242:34: warning: variable 's2mps11_dt_match'
is not needed and will not be emitted [-Wunneeded-internal-declaration]
static const struct of_device_id s2mps11_dt_match[] = {
^
1 warning generated.
This warning happens when a variable is used in some construct that
doesn't require a reference to that variable to be emitted in the symbol
table; in this case, it's MODULE_DEVICE_TABLE, which only needs to hold
the data of the variable, not the variable itself.
$ nm -S drivers/clk/clk-s2mps11.o | rg s2mps11_dt_match
00000078 000003d4 R __mod_of__s2mps11_dt_match_device_table
Normally, with device ID table variables, it means that the variable
just needs to be tied to the device declaration at the bottom of the
file, like s2mps11_clk_id:
$ nm -S drivers/clk/clk-s2mps11.o | rg s2mps11_clk_id
00000000 00000078 R __mod_platform__s2mps11_clk_id_device_table
00000000 00000078 r s2mps11_clk_id
However, because the comment above this deliberately doesn't want this
variable added to .of_match_table, we need to mark s2mps11_dt_match as
__used to silence this warning. This makes it clear to Clang that the
variable is used for something, even if a reference to it isn't being
emitted.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Fixes: 8985167ecf ("clk: s2mps11: Fix matching when built as module and DT node contains compatible")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a module license to match the license at the top of this file and
silence a build warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the Hfplls are reprogrammed during the rate change,
the primary muxes which are sourced from the same hfpll
for higher frequencies, needs to be switched to the 'safe
secondary mux' as the parent for that small window. This
is done by registering a clk notifier for the muxes and
switching to the safe parent in the PRE_RATE_CHANGE notifier
and back to the original parent in the POST_RATE_CHANGE notifier.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Krait CPU clocks are made up of a primary mux and secondary
mux for each CPU and the L2, controlled via cp15 accessors. For
Kraits within KPSSv1 each secondary mux accepts a different aux
source, but on KPSSv2 each secondary mux accepts the same aux
source.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ACC and GCC regions present in KPSSv1 contain registers to
control clocks and power to each Krait CPU and L2. For CPUfreq
purposes probe these devices and expose a mux clock that chooses
between PXO and PLL8.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Krait clocks are made up of a series of muxes and a divider
that choose between a fixed rate clock and dedicated HFPLLs for
each CPU. Instead of using mmio accesses to remux parents, the
Krait implementation exposes the remux control via cp15
registers. Support these clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
[sboyd@kernel.org: Move hidden config to top outside of the visible qcom
config zone so that menuconfig looks nice]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Describe the HFPLLs present on IPQ806X devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Describe the HFPLLs present on MSM8960 and APQ8064 devices.
Acked-by: Rob Herring <robh@kernel.org> (bindings)
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On some devices (MSM8974 for example), the HFPLLs are
instantiated within the Krait processor subsystem as separate
register regions. Add a driver for these PLLs so that we can
provide HFPLL clocks for use by the system.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
HFPLLs are the main frequency source for Krait CPU clocks. Add
support for changing the rate of these PLLs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6Q has MMDC0 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SL has MMDC0 and MMDC1 ipg clock in CCM CCGR, add them into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SLL has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6UL has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Move all the DT backward compatibility code to its own file so it can be
deleted later.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a driver for the PMC clocks of the at91sam9rl SoC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[sboyd@kernel.org: Make i signed to fix signedness bug]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a driver for the PMC clocks of the at91sam9x5 SoCs
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[sboyd@kernel.org: Make i signed to fix signedness bug]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a driver for the PMC clocks of the at91sam9260, at91sam9261,
at91am9263 and at91sam9g20 SoCs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[sboyd@kernel.org: Make i signed to fix signedness bug]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a driver for the PMC clocks of the sama5d2
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[sboyd@kernel.org: Make i signed to fix signedness bug]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a driver for the PMC clocks of the sama5d4
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[sboyd@kernel.org: Make i signed to fix signedness bug]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a new DT lookup function to lookup for PMC clocks.
Note that the #ifndef AT91_PMC_MOSCS section will be removed once all the
platforms are converted.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a new strut to handle references to all the PMC clocks and implement
allocation/free helpers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove static keyword to allow functions to be used from other units. Also
move some struct and function declarations to pmc.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[sboyd@kernel.org: Include pmc.h]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Set gck->audio_pll_allowed in at91_clk_register_generated. This makes it
easier to do it from code that is not parsing device tree.
Also, this fixes an issue where the resulting clk_hw can be dereferenced
before being tested for error.
Fixes: 1a1a36d72e ("clk: at91: clk-generated: make gclk determine audio_pll rate")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Separate registration out of of_sama5d2_clk_audio_pll*_setup to allow other
code to use it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[sboyd@kernel.org: Include pmc.h]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Separate registration out of of_sama5d4_clk_h32mx_setup to allow other code
to use it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the SSCs don't have gclk, don't check for their ID to allow them to set
the audio pll rate.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The allocation for the audio pmc is using the size of struct clk_audio_pad
instead of struct clk_audio_pmc. This works fine because the former is
larger than the latter but it is safer to be correct.
Fixes: ("0865805d82d4 clk: at91: add audio pll clock drivers")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A typo that makes it impossible to get the correct clocks for
MMP2_CLK_SDH2 and MMP2_CLK_SDH3.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Fixes: 1ec770d92a ("clk: mmp: add mmp2 DT support for clock driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7D uses virtual cpu clock of "arm" clock to be child clock
of "arm_a7_root_clk" and it is with CLK_IS_CRITICAL flag set, so
no need to add CLK_IS_CRITICAL flag for keeping "arm_a7_root_clk"
use count correct, latest clock tree is as below in clk_summary:
pll_arm_main 1 1 0 792000000 0
pll_arm_main_bypass 1 1 0 792000000 0
pll_arm_main_clk 1 1 0 792000000 0
arm_a7_src 1 1 0 792000000 0
arm_a7_cg 1 1 0 792000000 0
arm_a7_div 1 1 0 792000000 0
arm_a7_root_clk 1 1 0 792000000 0
arm 1 1 0 792000000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add CLK_IS_CRITICAL flag for cpu clock type to
make cpu clock use count correct, as cpu clock
should be always critical.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the signedness bug returning '(-22)' on the return type by removing the
sanity checker in rockchip_ddrclk_get_parent(). The function should return
and unsigned value only and it's safe to remove the sanity checker as the
core functions that call get_parent like clk_core_get_parent_by_index already
ensures the validity of the clk index returned (index >= core->num_parents).
Fixes: a4f182bf81 ("clk: rockchip: add new clock-type for the ddrclk")
Cc: stable@vger.kernel.org
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
and generating noise.
-----BEGIN PGP SIGNATURE-----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=Vt/u
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Stephen writes:
"clk fixes for v4.19-rc8
One fix for the Allwinner A10 SoC's audio PLL that wasn't properly
set and generating noise."
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: sun4i: Set VCO and PLL bias current to lowest setting
The parent clock is get only to have its name, and then the clock is no
more used, so we can safely free it using clk_put. Furthermore as between
the successful devm_clk_get() and the devm_clk_put() call we don't exit
the probe function in error so I can use non managed version of clk_get()
and clk_put().
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch introduces the managed version of clk_bulk_get_all.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch introduces of_clk_bulk_get_all and clk_bulk_x_all APIs
to users who just want to handle all available clocks from device tree
without need to know the detailed clock information likes clock numbers
and names. This is useful in writing some generic drivers to handle clock
part.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
'clock-names' property is optional in DT, so of_clk_bulk_get() is
introduced here to handle this for DT users without 'clock-names'
specified. Later clk_bulk_get_all() will be implemented on top of
it and this API will be kept private until someone proves they need
it because they don't have a struct device pointer.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reported-by: Shawn Guo <shawnguo@kernel.org>
Tested-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
You can't compile this file by itself because it uses SZ_64K from
sizes.h but doesn't include it. Instead it relies on some certain
configuration pulling that in implicitly somewhere else. Just add the
include to make random compile testing easier.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix some incorrect data in LVL2 offset and bit mask.
Fixes: e403d00573 ("clk: tegra: MBIST work around for Tegra210")
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Actually report the error code from devm_regulator_get() which may as
well just be a probe deferral.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On i.MX7D, IMX7D_NAND_USDHC_BUS_ROOT_CLK is NOT necessary
for system, and IMX7D_AHB_CHANNEL_ROOT_CLK is NOT existing
at all, remove them from clks_init_on array.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the clocks provided by the CGU in the Ingenic JZ4725B
SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Previously, the CGU code corresponding to the SoC for which we're
compiling the kernel was the only one enabled, which made it impossible
to build one kernel that supports them all.
Now, it is possible to select more than one SoC to support.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the clocks supported in global clock controller which clock the
peripherals like BLSPs, SDCC, USB, MDSS etc. Register all the clocks
to the clock framework for the clients to be able to request for them.
Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Co-developed-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
[bamse, vkoul: rebase and tidyup for upstream]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@kernel.org: Lowercase hex]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is used by the QCS404 GCC driver, export it to allow that driver to
be compiled as a module..
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the global clock controller found on SDM660
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Based on CAF implementation.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[craig: rename parents to fit upstream, and other cleanups]
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@kernel.org: Rename gcc_660 to gcc_sdm660 and fix numbering of
defines to avoid duplicates]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit a982e45dc1 ("clk: at91: PLL recalc_rate() now using cached MUL
and DIV values") removed a check that prevents a division by zero. This
now causes a stacktrace when booting the kernel on a at91 platform if
the PLL DIV register contains zero. This commit reintroduces this check.
Fixes: a982e45dc1 ("clk: at91: PLL recalc_rate() now using cached...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ronald Wahl <rwahl@gmx.de>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When driver is built as module and DT node contains clocks compatible
(e.g. "samsung,s2mps11-clk"), the module will not be autoloaded because
module aliases won't match.
The modalias from uevent: of:NclocksT<NULL>Csamsung,s2mps11-clk
The modalias from driver: platform:s2mps11-clk
The devices are instantiated by parent's MFD. However both Device Tree
bindings and parent define the compatible for clocks devices. In case
of module matching this DT compatible will be used.
The issue will not happen if this is a built-in (no need for module
matching) or when clocks DT node does not contain compatible (not
correct from bindings perspective but working for driver).
Note when backporting to stable kernels: adjust the list of device ID
entries.
Cc: <stable@vger.kernel.org>
Fixes: 53c31b3437 ("mfd: sec-core: Add of_compatible strings for clock MFD cells")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add Reset Management Unit (RMU) support for Actions Semi S900 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add Reset Management Unit (RMU) support for Actions Semi S700 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add Reset Management Unit (RMU) support for Actions Semi Owl SoCs.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In order to support the reset controller, regmap info needs to
be cached in the private clock descriptor, owl_clk_desc. Hence,
save that and also make the clock descriptor struct non const.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Another patch is going to change this code to use %pOFn for DT node
names. Fix up the code to make this easy to pick this side of the merge
instead of fixing it up in a merge commit later.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The normal style is to use 'core' for struct clk_core pointers and to
directly access the core pointer from the clk_hw pointer when we're
within the common clk framework. Update the patches to make it a bit
easier to handle.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patchset adds CCF compliant clock driver for ZynqMP.
Clock driver queries supported clock information from firmware
and regiters pll and output clocks with CCF.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlu8k7oACgkQykllyylKDCFmPACfewJHUsKUhaX77Ew+Pup5tFzC
GHgAn1Xb2fJF+9D4CSB+iwdQNPltuhBg
=QShK
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-clk-for-v4.20' of https://github.com/Xilinx/linux-xlnx into next/drivers
arm64: zynqmp: SoC CLK changes for v4.20
This patchset adds CCF compliant clock driver for ZynqMP.
Clock driver queries supported clock information from firmware
and regiters pll and output clocks with CCF.
* tag 'zynqmp-soc-clk-for-v4.20' of https://github.com/Xilinx/linux-xlnx:
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds CCF compliant clock driver for ZynqMP.
Clock driver queries supported clock information from
firmware and regiters pll and output clocks with CCF.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Tejas Patel <tejasp@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A randconfig build showed that two clk modules have no license tag:
WARNING: modpost: missing MODULE_LICENSE() in drivers/clk/keystone/gate.o
see include/linux/module.h for more information
WARNING: modpost: missing MODULE_LICENSE() in drivers/clk/keystone/pll.o
see include/linux/module.h for more information
Add the appropriate information from the comment at the start of the
two files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <ssantosh@krenel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_notifier_register() documentation states, that the provided notifier
callbacks associated with the notifier must not re-enter into the clk
framework by calling any top-level clk APIs. Fix this by replacing
clk_get_rate() calls with clk_hw_get_rate(), which is safe in this
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Ensure that clocks for core SoC modules (including TZPC0..9 modules)
are enabled for suspend/resume cycle. This fixes suspend/resume
support on Exynos5422-based Odroid XU3/XU4 boards.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
The bit of GATE_BUS_PERIS1 for CLK_SECKEY is just reserved on
exynos5422/5800, not exynos5420. Define gate clk for exynos5420 to
handle the bit only on exynos5420.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[m.szyprow: rewrote commit subject]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
All sclk_uart clocks in TOP CMU have to be kept enabled for suspend/resume
cycle, otherwise TM2(e) boards hangs before entering the suspend mode.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Exynos4412 ISP clock are provided by separate Exynos4412 ISP clock
driver, so support for them in Exynos4-clk driver can be removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Before entering system suspend, one has to ensure that some clocks from
TOP, CPIF and PERIC CMUs are enabled. This is needed by the firmware
to properly perform system suspend operation. Instead of adding more and
more clocks with CRITICAL flag, simply enable those clocks directly in
respective CMU registers using 'suspend_regs' feature.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
SoC clock drivers should suspend after every other drivers in the system,
which are using clocks and resume before them. The last stage for calling
suspend device callbacks is NOIRQ stage and there exists driver, which use
that state (dwmmc-exynos), so Exynos5433 clocks driver should also use it.
During the same stage, clocks driver will be always suspended after its
clients as a direct result of proper device probe order (deferred probe
reorders the suspend call sequence).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Replace common suspend/resume handling code by generic helper.
Handling of PLLs is a bit different in generic code, as they are handled
in the same way as other clock registers. Such approach was already used
on later Exynos SoCs and worked fine. Tests have shown that it works also
on Exynos4 SoCs and significantly simplifies the code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Some registers of clock controller have to be set to certain values before
entering system suspend state. Till now drivers did that on their own,
but it will be easier to handle it by generic code and let drivers simply
to provide the list of registers and their state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
[snawrocki@kernel.org: Whitespace correction]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Aisheng Dong