When we stop the Tx DMA channels, we poll bits 16:31 in
FH_TSSR_RX_STATUS_REG. From 4965 and up, only the bits 16:26 are legal.
Bits 27:31 are not used and are always unset.
Polling them will lead to fail on timeout but since the timeout is quite
small, the stall was not felt.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Intel Wireless WiFi Next Gen AGN support two major categories:
1. Intel Wireless WiFi 4965 AGN device
2. Intel Wireless-N/Advanced-N/Ultimate-N family
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
ucode errors were redefined in new ucode images and all new errors
were showing as advanced sysasserts which was misleading. new errors
are not sequential so additional lookup table added. errors do not
overlap so both are used to support older and newer ucode images.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
To enable 6050 series Gen 2 devices:
1) new PCI_IDs are added;
2) new EEPROM version and calibration version numbers defined;
3) new hardware REV number defined;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For newer devices (6000g2a and 6000g2b), the sensitivity table send to
uCode require additional table entries to help sensitivity calibration.
All the additional entries has fix data for now, but do expect the value
will be change in the future when device become more stable.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Code clean up to change name from having 5000 as part of name which easy
to confuse and think it is for 5000 series devices to more
generic _agn name since it is being used by multiple _agn devices.
No functional changes.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"Flush" request can come from two different sources, it can either from
mac80211, or from device when the operation is needed. Here
adding the support for device issue "flush" request.
When receive tx complete with status is TX_STATUS_FAIL_RFKILL_FLUSH,
issue REPLY_TXFIFO_FLUSH command to uCode to flush out all the tx frames
in queues.
In this condition, since mac80211 has no knowledge of "flush" operation,
driver need to stop all the tx queues and wait for the operation
completed before wake up the queues for frames transmission.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Adding flush callback support in the driver. Two type of flush can be
issued by mac80211:
1. drop = true: frame drop is ok, issue REPLY_TXFIFO_FLUSH host command
to uCode to drop all the frames in tx fifo queues; then return the
control back to mac80211
2. drop = false: wait for either all the frames in tx fifo queues been
transmitted, or timeout; then return the control back to mac80211
If the flush request coming from mac80211, mac80211 will make sure there
are no additional frames push down to driver before flush operation is
completed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When parsing TLV during loading firmware, if encounter any TLV error,
log the error message to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
fw_restart module parameter was broken by the recent check for stuck
queue patch, driver check the fx_restart module parameter
before reload the firmware; but the stuck queue timer kick in after
firmware error and reload the firmware even fw_restart=0. In this case,
driver should not reload the firmware, it is important to help debugging
uCode error.
The only case we can ignore the module parameter is when user request
firmware reload from debugfs, which can bypass the checking and perform
firmware reload all the time.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.
The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Radio calibration (chain noise and sensitivity) should be allowed to
be disabled from debugfs if compiled with CONFIG_IWLWIFI_DEBUGFS. For both
6000g2a and 6000g2b, the parameters are missing in "cfg", which cause
user can not disable the radio calibration manually; add the support to
allow the operation.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This message is encountered regularly and we need to take a closer look at
the circumstances under which it is printed before presenting errors to
users.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
If RTS/CTS protection is needed for HT, wait until get operational
notification from mac80211, then inform uCode to switch to RTS/CTS
through RXON command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When resuming from hibernate or suspend,
the status of the rfkill switch isn't
known since it might have been toggled
while the system was asleep. Therefore,
we need to read out the status at resume
time to make sure the system knows about
an up-to-date status.
Reported-by: Mark Tung <mark.y.tung@intel.com>
Tested-by: Mark Tung <mark.y.tung@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The rate table in the bcast LQ is computed only when the station is
allocated, and chooses the lowest rate for the band. Because of when this
occurs, this is the 2.4 GHz band and uses the 0x420a (CCK, 1 Mbps) rate. In 5 GHz
beaconing mode, this rate will prevent beacons from being sent and any other
packets from being received.
We can fix this by re-initializing the bcast station's LQ command when the
channel is changed.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For some devices, especially the upcoming new devices, the plcp error
rate is different. Before the correct error rate can be determine, also
for the debugging purpose; add the mechanism to disable plcp error checking
which cause radio reset happen.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Different devices have different calibration requirement,
some need DC calibration and some don't; make it a cfg parameter
for easy management.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This bit need to be set for both RTS/CTS or CTS-to-self protection, if
CTS-to-self is used, then uCode will check the RXON_FLG_SELF_CTS_EN
status. Change the name from TX_CMD_FLG_RTS_CTS_MSK to TX_CMD_FLAG_PROT_REQUIRE_MSK
to match the behavior of the bit setting.
Also update comments to reflect which hardware uses which of the TX command
flags.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.
Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:
commit 1152dcc28c
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Fri Jan 15 13:42:58 2010 -0800
iwlwifi: Fix throughput stall issue in HT mode for 5000
Similar to 6000 and 1000 series, RTS/CTS is the recommended
protection mechanism for 5000 series in HT mode based on the HW design.
Using RTS/CTS will better protect the inner exchange from interference,
especially in highly-congested environment, it also prevent uCode encounter
TX FIFO underrun and other HT mode related performance issues.
For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Apr 29 04:43:05 2010 -0700
iwlwifi: apply filter flags directly
broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.
The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).
Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the reference to non-exist function in iwlcore
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Break out of loop and log the error message when encounter error; this is
better approach than using "goto".
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
All the calibrations are "agn" only functions, move from iwlcore to
iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
agn and 3945 has different statistics_notif data structure; since 3945
has it statistics_notif data structure inside the _3945 portion of
iwl_priv, it make sense to move the agn statistics_notif into _agn
portion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
To avoid having unnecessary functions in iwlcore.ko, those that
are not shared by agn and 3945, move agn specific rx related code
to iwl-agn-rx.c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
errors are defined in hex but displayed as decimal. displaying as hex
debugging easier and eliminated having to manually convert.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When station management calls to ucode return
an error we could previously do nothing, but
now that almost all calls are synchronous we
can actually let the error bubble up. Use EIO
as the error as it best indicates a problem
with the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Key management can use sync commands
instead of asynchronous ones to have
better error checking.
Also add checks that the commands all
should have the mutex held.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Now that the ampdu_action callback can sleep,
we can use the mutex to properly protect the
aggregation data, and return useful errors if
they should happen.
Also, add some sleep and mutex debugging so
we won't call any of the functions that now
require being able to sleep and/or the mutex
to be held in an invalid context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we detect that not all antennas are
properly connected, we simply disable the
associated chains, but never notify the
user at all. Print out a warning so it is
obvious that happened and we know where
to start looking for related issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl4965_rx_mpdu_res_start is not 4695 specific, so rename it to more
general name iwl_rx_mpdu_res_start.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename rxq->dma_addr to rxq->bd_dma to better emphasize that the
physical address stands for the receive buffer descriptor's address.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cancel scheduled run time calibration work when interface is going
down.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Test for null pointer prior to access.
Print "Not Allocated" if null pointer.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The length contained in the status word doesn't
include the status word's length itself, so we
need to account for that for tracing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The flow id (scd_flow) in a compressed BA packet should match the txq_id
of the queue from which the aggregated packets were sent. However, in
some hardware like the 1000 series, sometimes the flow id is 0 for the
txq_id (10 to 19). This can cause the annoying message:
[ 2213.306191] iwlagn 0000:01:00.0: Received BA when not expected
[ 2213.310178] iwlagn 0000:01:00.0: Read index for DMA queue txq id (0),
index 5, is out of range [0-256] 7 7.
And even worse, if agg->wait_for_ba is true when the bad BA is arriving,
this can cause system hang due to NULL pointer dereference because the
code is operating in a wrong tx queue!
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Pradeep Kulkarni <pradeepx.kulkarni@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We are seeing some race conditions between incoming station management
requests (station add/remove) and the internal unassoc RXON command that
modifies station table. Modify these flows to require the mutex to be held
and thus serializing them.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2207
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Using ieee80211_find_sta() needs to be under
RCU read lock, which iwlwifi currently misses,
so fix it.
Cc: stable@kernel.org
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the revert of "iwlwifi: move _agn statistics related structure", I
need to use CONFIG_IWLWIFI_DEBUGFS instead of CONFIG_IWLWIFI_DEBUG in
the private structure definition. Without this patch, it is possible
to get this:
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_accumulative_statistics':
drivers/net/wireless/iwlwifi/iwl-rx.c:304: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:305: error: 'struct iwl_priv' has no member named 'delta_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:306: error: 'struct iwl_priv' has no member named 'max_delta'
drivers/net/wireless/iwlwifi/iwl-rx.c:321: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:323: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:325: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:327: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:329: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:331: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_reply_statistics':
drivers/net/wireless/iwlwifi/iwl-rx.c:484: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:486: error: 'struct iwl_priv' has no member named 'delta_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:488: error: 'struct iwl_priv' has no member named 'max_delta'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fairly complex code in iwlagn_tx_status_reply_tx handle the status reports for
aggregated packet batches sent by the NIC. This code aims to handle the case
where the NIC retransmits failed packets from a previous batch; the status
information for these packets can sometimes be inserted in the middle of a
batch and are actually not in order by sequence number! (I verified this can
happen with printk's in the function.)
The code in question adaptively identifies the "first" frame of the batch,
taking into account that it may not be the one corresponding to the first agg
status report, and also handles the case when the set of sent packets wraps the
256-character entry buffer. It generates the agg->bitmap field of sent packets
which is later compared to the BlockAck response from the receiver to see which
frames of those sent in this batch were ACKed. A small logic error (wrapping by
0xff==255 instead of 0x100==256) was causing the agg->bitmap to be set
incorrectly.
Fix this wrapping code, and add extensive comments to clarify what is going on.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Compressed BlockAck frames store the ACKs/NACKs in a 64-bit bitmap that starts
at the sequence number of the first frame sent in the aggregated batch. Note
that this is a selective ACKnowledgement following selective retransmission;
e.g., if frames 1,4-5 in a batch are ACKed then the next transmission will
include frames 2-3,6-10 (7 frames). In this latter case, the Compressed
BlockAck will not have all meaningful information in the low order bits -- the
semantically meaningful bits of the BA will be 0x1f3 (where the low-order frame
is seq 2).
The driver code originally just looked at the lower (in this case, 7) bits of
the BlockAck. In this case, the lower 7 bits of 0x1f3 => only 5 packets,
maximum, could ever be ACKed. In reality it should be looking at all of the
bits, filtered by those corresponding to packets that were actually sent. This
flaw meant that the number of correctly ACked packets could be significantly
underreported and might result in asynchronous state between TX and RX sides as
well as driver and uCode.
Fix this and also add a shortcut that doesn't require the code to loop through
all 64 bits of the bitmap but rather stops when no higher packets are ACKed.
In my experiments this fix greatly reduces throughput swing, making throughput
stable and high. It is also likely related to some of the stalls observed in
aggregation mode and maybe some of the buffer underruns observed, e.g.,
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1968http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2098http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2018
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The internal scanning created a problem where
when userspace tries to scan, the scan gets
rejected. Instead of doing that, queue up the
user-initiated scan when doing an internal
scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In "iwlwifi: make scan antenna forcing more generic"
I introduced generic scan RX antenna forcing, which
here I rename to make it more evident. Also add scan
TX antenna forcing, since I will need that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Channel switch host command do not need to allocate huge command buffer
since its size is already included in the iwl_device_cmd structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently, the driver allocates up to 19 skb pointers
for each TFD, of which we have 256 per queue. This
means that for each TX queue, we allocate 19k/38k
(an order 4 or 5 allocation on 32/64 bit respectively)
just for each queue's "txb" array, which contains only
the SKB pointers.
However, due to the way we use these pointers only the
first one can ever be assigned. When the driver was
initially written, the idea was that it could be
passed multiple SKBs for each TFD and attach all
those to implement gather DMA. However, due to
constraints in the userspace API and lack of TCP/IP
level checksumming in the device, this is in fact not
possible. And even if it were, the SKBs would be
chained, and we wouldn't need to keep pointers to
each anyway.
Change this to only keep track of one SKB per TFD,
and thereby reduce memory consumption to just one
pointer per TFD, which is an order 0 allocation per
transmit queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we allocate queues, we currently don't
use kzalloc() right now. When we then free
those queues again without having used all
entries, we may end up trying to free random
pointers found in the txb array since it was
never initialised. This fixes it simply by
using kzalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The iwl_hw_txq_free_tfd() function can be
called from contexts with IRQs disabled,
so it must not call dev_kfree_skb() but
rather dev_kfree_skb_any() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we free a txq that had no txb array allocated,
we still try to access it. Fix that, and also free
all SKBs that may be in the txb array (although it
can just be a single one).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This variable is now no longer used, so it
can be removed completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
use TIME_UNIT define for beacon internal calculation
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Support channel switch in driver as a separated mac80211 callback
function instead of part of mac_config callback; by moving to this
approach, uCode can have more control of channel switch timing.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the ucode beacon formation related helper function from 3945 to
iwlcore, so both _3945 and _agn devices can utilize those functions.
When driver pass the beacon related timing information to uCode in both
spectrum measurement and channel switch commands, the beacon timing
parameter require in uCode beacon format; those helper functions will do
the conversation from uSec to the correct uCode format
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
restrict_refcnt is no longer used, remove it from iwl_priv
structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Chain noise calibration data are cleared after the calibration is done
in iwlagn_gain_computation() and iwl4965_gain_computation(). This cause
the debugfs entries for those data useless. To provide valid debugging
info, clear those data right before starting the calibration instead.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This can now be much better achieved using
tracing and post-processing of the trace,
rather than doing the processing in place
in the driver, so remove a lot of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For probe request frames sent during scan, we
should use the virtual interface's mac address
that the scan was initiated on to avoid issues
when the wrong address is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we do not have an interface, priv->mac_addr
is all zeroes, so the memcpy() is not useful as
the RXON buffer has been cleared previously.
Therefore, use the interface's address that we
are setting up the RXON for, if available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
priv->mac_addr is the address of the operating
interface, not the permanent MAC address. They
are usually the same, but the user can override
the operating address, so we shouldn't set the
variable to the permanent one, it is assigned
when an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
There's no microcode that actually uses this
variable, and it is reserved for functionality
that the driver doesn't support anyway, so we
shouldn't be setting it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_connection_init_rx_config() will already
have set up the entire RXON command, so these
assignments are duplicate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Port of internal scan to iwl3945 missed introduction
of iwl3945_get_single_channel_for_scan.
Fix the following bug by introducing the iwl3945_get_single_channel_for_scan
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2208
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This can be cleanly applied to wireless-2.6 and iwlwifi git trees.
=
From: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Subject: [PATCH] iwlwifi: use the DMA state API instead of the pci equivalents
This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.
No functional change.
For further information about the background:
http://marc.info/?l=linux-netdev&m=127037540020276&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.
The debugfs code I recently added got this wrong
as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a single use of this struct member, but
as it is write-only it clearly not necessary.
Thus we can free up some space here, even if we
don't need it right now it seems pointless to
carry around the variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a2064b7a4a.
when CONFIG_IWLAGN=n:
drivers/net/wireless/iwlwifi/iwl-rx.c:254: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:303: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:304: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:305: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:306: error: 'struct iwl_priv' has no member named '_agn'
and many more.
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn-debugfs.c
drivers/net/wireless/iwlwifi/iwl-debugfs.c
drivers/net/wireless/iwlwifi/iwl-dev.h
drivers/net/wireless/iwlwifi/iwl-rx.c
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intent here is to test that "sta_id_r" is a valid pointer. We do
this same test later on in the function.
Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.
Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
there is some locking missing around the "is_internal_short_scan"
variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
scan and thus causes problems with wrong memory being accessed.
The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
switch and while statements don't need semicolons at end of statement
[ Fixup minor conflicts with recent wimax merge... -DaveM ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new PCI IDs for 6000 Series Gen2 devices
and also defines a new sku of device: 6000g2b 2x2 bgn.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cleanup the code and move all the uCode related functions specific to _agn
devices to iwl-agn-ucode.c
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The short preamble setting might change on the
fly, and then we already use the right mac80211
variable. However, in other places we don't,
which is especially wrong in the AP code since
in that case the assoc_capability is invalid.
Also, the IBSS special case is not needed since
"use_short_slot" will be properly cleared, but
the "assoc_capability" might be invalid (which
must be the reason for the special case).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
It may be desirable in some systems to have
insight into the driver via debugfs, but not
affect its operation via the debug logging
code that is inserted everywhere when DEBUG
is configured.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some comments in iwl-dev.h still refer to 4965 but used by all the _agn
devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move configuration structure for _agn devices from iwl-dev.h to
iwl-agn.h. Those data structures are for _agn devices and should be keep
for _agn devices only.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch enables all remaining 6000 series Gen2 devices.
To work-around a firmware crash problem, we disable sending
bt coex command for 6000g2b series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In order to debug problems before the ALIVE
notification is received, new firmware files
contain the event/error log information in
the file. Use that information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
There are a few places where sta_lock is used, but the
station information protected by it is accessed outside
of the lock. Address this in two ways, if the access
won't sleep then just move the access into the lock, if
the access can sleep then copy the needed station
information to the stack to be accessed without risk of
it changing while access in progress.
Additionally, a number of other places access station
station information without holding the sta_lock, fix
those as well.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This constant is not used, and incorrect, since
the broadcast ID must be used for multicast too.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The stations debugfs entry doesn't even show
the stations' MAC addresses Also, the TID
information is formatted very oddly, and
misses the important tfds_in_queue variable.
Fix this to make the file more useful.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is only used by the agn drivers,
so doesn't have to be in core and exported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Unlike agn, where the sequence numbers must
match with the TFD index, the driver for 3945
devices can use the sequence numbers provided
by mac80211 for QoS frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
If a firmware file misses one of the required
instruction or data pieces, the driver currently
crashes. Let it gracefully refuse that firmware
file instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since agn and 3945 have different statistics_notif data structure, each
should has its own statistics_flag function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
agn and 3945 has different statistics_notif data structure; since 3945
has it statistics_notif data structure inside the _3945 portion of
iwl_priv, it make sense to move the agn statistics_notif into _agn portion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
There are now five places where we need to
look up the station ID, but the sta pointer
may be NULL due to mac80211 passing that to
indicate a certain special state.
Replace all these by a new inline function,
called iwl_sta_id_or_broadcast(), and add
documentation about when to use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
During a hw restart, mac80211 will attempt to
reconfigure all stations. Currently, that fails
and leads to warnings because we still have the
stations marked active. Therefore, clear all
stations when doing down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Remove the check before invoking iwl_set_ht_add_station(),
since neither of the conditions in this check makes sense,
as either we pass in a NULL ht_info (first branch) or in
the IBSS case an ht_info with ht_enabled=false.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is now only used for the special
IBSS BSSID station, so rename it to indicate
this. The new name is iwl_add_bssid_station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
4965 code is the only thing that now still
needs iwl_find_station(), so move it there
and make it static. Everything else can
rely on the station data passed by mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With the station ID being stored in the
station struct, which mac80211 gives us
for TKIP phase 1 key updates, we can also
remove the use of iwl_find_station() in
that code path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With the station ID being stored in the
station struct, which mac80211 gives us
for aggregation callbacks, we can also
remove the use of iwl_find_station() in
those code paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since we now store the station ID in each station
struct, many places need not look at the station
table any more since they can just pull the station
ID out of the struct. Remove iwl_get_sta_id() and
use iwl_sta_id() instead as appropriate.
This reduces the amount of code needed to find the
right station significantly, and works since
mac80211 passes the station only after it has been
fully initialised, ie. even if TX races with
station addition it will only be passed to TX once
the addition is complete.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In places where the station struct is
guaranteed to exist (presumably), use
this helper to get the station ID out
of it (and warn if there's no station
struct after all).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 allows us to store private data per
station, so put the station ID there. This
allows us to avoid the station ID lookup when
removing regular stations. To also be able to
avoid the lookup to remove the special IBSS
BSSID station, track its ID in the per-vif
private data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Provide comments for newly added cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move "tx power per chain" into ucode_tx_stats, it is debugging
information provided by uCode as part of statistics notification.
The "tx power per chain" parameters are optional parameters which only
supported by 6000 series device today; those are reserved fields for all
the other devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When station is using an HT channel to communicate to AP and communication
is lost then driver will first be notified that channel is not an HT
channel anymore before AP station is removed. A consequence of that is that
the driver will know that it is not communicating on HT anymore, but the
rate scaling table is still under the impression it is operating in HT. Any
time after driver has been notified channel is not HT anymore there will
thus be a firmware SYSASSERT when the current active LQ command is sent.
A workaround for this issue is to not send a LQ command in the short time between
being notified channel is not HT anymore and rate scaling table being
updated.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2173
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently, the broadcast station is managed along
with the interface type, rather than always being
present. That leads to a bug with injection -- it
is currently not possible to inject frames when
the only virtual interface is a monitor, because
in that the required broadcast station is missing.
Additionally, allocating and deallocating the
broadcast station's LQ all the time is wasteful,
and the code to support this is fairly complex.
So this changes completely the way we manage the
broadcast station. Rather than manage it along
with any interface, we now allocate it when we
bring the device up, and remove it again when we
bring the device down. When we bring the device
up, we don't immediately program the broadcast
station into it, instead we just mark it active
and rely on the next restore cycle to upload it
to the device. This works because an unassociated
RXON is always required at least once to set up
device parameters, which implies a reprogramming
of stations into the device.
As we now manage all stations properly, there no
longer is a need for forcing a clearing of them
via iwl_clear_ucode_stations(), which can become
a lot simpler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename iwl_sta_init_lq to iwl_sta_alloc_lq and
move sending it out into the caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The "is_ap" argument to iwl_sta_init_lq is never true,
so it and the corresponding code can be removed. However,
it needs to have the station ID because it is also used
for the IBSS BSSID station, and that doesn't have the
broadcast ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The bssid member of struct iwl_priv is now
only used by 3945 code, so note that. It
shouldn't be used by any other code in the
future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Pass the virtual interface pointer to iwl_ht_conf()
so it doesn't need to rely on iw_mode and other
global variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This check is not useful, since we now no
longer dereference priv->vif at this spot.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Most of the TX aggregation handling can be passed
the virtual interface directly instead of having
to rely on priv->vif.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rather than keeping every bit of information
around in priv and the virtual interface, add
a virtual interface to many functions and use
the information directly from it.
This removes beacon_int, assoc_capability and
assoc_id from struct iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since iwl_configure_filter can now sleep since
the mac80211 callback was changed, we can now
apply filter flags changes directly.
Also, while at it, make the code a bit more
generic with a local macro. There's no need
to check changed_flags since we apply all at
the same time anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We need not check iw_mode, since we have
the vif pointer available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is only needed by 4965, so
it need not be in core code and can be
made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We never use that member of struct iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add plcp error checking for 3945. After threshold of plcp
is reached , it resets the radio
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The old firmware file type does not allow indicating
any firmware capabilities, which we frequently want
to make things easier.
This implements a new firmware type that is based on
a TLV structure, and adds a TLV for the maximum length
of probe requests in scans.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently the first four bytes in a firmware file
indicate the major, minor and api versions as well
as the serial number. These combined can never be
zero, so we can use that special case for a new,
future, file format.
This patch simply shuffles the code and prepares
for that new format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
It doesn't belong into firmware loading,
it should instead be printed after loading
the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
AGN devices all use the same ucode operations,
except for 4965, because 4965 uses only v1 file
headers.
Therefore, we can remove all the indirection
we have here and just code the API distinction
in place, with a small special case for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
As these function pointers will always point to
the 3945 functions, we can just call them directly
and avoid the indirection.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We currently display the build number only if debugging
is enabled, but it is really helpful so show it all the
time. Also store it so it can be retrieved later via
ethtool.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently iwlwifi will eventually exhaust the station
table when adding the BSSID station for IBSS mode,
unless the interface is set down.
The new mac80211 ibss joined/left notification allows
us to fix that easily by moving the code to add the
IBSS station to the notification, and also adding
code to remove it again when we leave the IBSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We'll need that function for IBSS station management,
so pass it the address, which is the only thing it
uses from the station struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl3945 should not use iwl_add_local_station(..., false)
because that would leave the IWL_STA_UCODE_INPROGRESS flag
set for the station, which is not desirable. Instead it
can use iwl3945_add_bcast_station() here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When adding the broadcast station the link quality command is
generated on demand, sent to device, and disappears. It is thus not
available for later cases when we need to restore stations and need
to send the link quality command afterwards. Now, when first adding the
broadcast station, also generate its link quality command to always be
available for later restoring.
Also fix an issue when adding local stations where the "in progress" state
is never cleared.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Dump the firmware version and build number in case of firmware SW
error. This would help firmware engineer analyze the error log.
Requested-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy