Commit Graph

151 Commits

Author SHA1 Message Date
Greg Kroah-Hartman 7706abf5a0 Merge 4.14-rc6 into staging-next
We want the IIO and staging driver fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-23 14:29:43 +02:00
Lukas Wunner c1375d671a iio: adc: mcp320x: Add support for mcp3550/1/3
These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but
in reality their resolution is 21 bit with an overrange or underrange
of 12% beyond Vref.  In other words, "full scale" means +/- 2^20.

This driver does not explicitly signal back to the user when an
overrange or underrange occurs, but the user can detect it by comparing
the raw value to +/- 2^20 (or the scaled value to Vref).

The chips feature an extended temperature range and high accuracy,
low noise characteristics, but their conversion times are slow with
up to 80 ms +/- 2% (on the MCP3550-50).

Hence, unlike the other ADCs supported by the driver, conversion does
not take place in realtime upon lowering CS.  Instead, CS is asserted
for 8 usec to start the conversion.  After waiting for the duration of
the conversion, the result can be fetched.  While waiting, control of
the bus is ceased so it may be used by a different device.

After the result has been fetched and 10 us have passed, the chip goes
into shutdown and an additional power-up delay of 144 clock periods is
then required to wake the analog circuitry upon the next conversion
(footnote below table 4-1, page 16 in the spec).

Optionally, the chips can be used in so-called "continuous conversion
mode":  Conversions then take place continuously and the last result may
be fetched at any time without observing a delay.  The mode is enabled
by permanently driving CS low, e.g. by wiring it to ground.  The driver
only supports "single conversion mode" for now but should be adaptable
to "continuous conversion mode" with moderate effort.

The chips clock out a 3 byte word, unlike the other ADCs supported by
the driver which all have a lower resolution than 16 bit and thus make
do with 2 bytes.  Calculate the word length on probe by rounding up the
resolution to full bytes.  Crucially, if the clock idles low, the
transfer is preceded by a useless Data Ready bit which increases its
length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec).
Autosense this based on the SPI slave's configuration.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-09 21:01:36 +01:00
Geert Uytterhoeven af5d716a90 iio: adc: rcar-gyroadc: Enable compile-testing on non-ARM
The rcar-gyroadc driver compiles fine on other platforms, hence increase
compile coverage.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-09 20:50:46 +01:00
Randy Dunlap 5151b4afb4 iio: adc: dln2-adc: fix build error
The dln2-adc driver uses interface(s) that are controlled by the
IIO_TRIGGERED_BUFFER Kconfig symbol, so the driver needs to select
that symbol to prevent the build error.

drivers/iio/adc/dln2-adc.o: In function `dln2_adc_probe':
dln2-adc.c:(.text+0x528): undefined reference to `devm_iio_triggered_buffer_setup'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-08 11:42:00 +01:00
Arnd Bergmann 3f09b8d2ea iio: adc: select triggered buffer for sama5d2 adc
Without the triggered buffer code, we get a link error:

drivers/iio/adc/at91-sama5d2_adc.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x938): undefined reference to `devm_iio_triggered_buffer_setup'

This adds a Kconfig 'select' statement like other ADC
drivers have it already.

Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-17 15:37:14 +01:00
Alexander Sverdlin 8614206a05 iio: adc: New driver for Cirrus Logic EP93xx ADC
New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-25 19:56:23 +01:00
Jack Andersen 7c0299e879 iio: adc: Add support for DLN2 ADC
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.

Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-07-09 18:17:18 +01:00
Mike Looijmans 1d3eacbfa6 iio: Add LTC2471/LTC2473 driver
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.

Datasheet:
  http://cds.linear.com/docs/en/datasheet/24713fb.pdf

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-04 20:50:04 +01:00
Fabio Estevam edd80a5f51 iio: adc: Kconfig: Append vendor name for IMX7D_ADC
To keep IMX7D_ADC text consistent with other iio/adc entries, add
the vendor name to the driver menu text.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-01 10:16:38 +01:00
Greg Kroah-Hartman ca9280d1f8 First set of new device support, features and cleanups for IIO in the 4.13 cycle
Two entirely new drivers in here plus the usual range of cleanups and features.
 
 New device support
 * ad5064
   - add ltc2631, ltc2633 and ltc2635 support.
 * bma180
   - trivial support for bma250e (new id)
 * hid-sensor-rotation
   - add relative orientation and geometric orientation support.
 * isl29028
   - add isl29030 support (its effectively the same part from a driver point of
   view)
 * maxim_thermocouple
   - add max31856 id.
 * meson-saradc
   - add meson8b SoC adc support.
 * ti-adc084s021
   - new driver and bindings.
 * ti-adc108s102
   - new driver and bindings.
 
 Staging graduations
 * isl29028
 
 Features
 * bma180
   - ACPI enumeration for BMA250E which is used in various x86 tablets.
 * hi8453
   - add raw access rather than only events.
 * hid-sensor-hub
   - Implement batch mode in which we can set a threshold on the amount of time
   between data coming from the fifos.  This is the first device to do this
   rather than use a watershed on the number of samples.
 * hts221
   - power management support
 * lsm6dsx
   - add system power management support.
 * rpr0521
   - sampling frequency read / write
 * stm32-trigger
   - add support for TRG02 triggers.
 * tsl2583
   - runtime power management support.
 
 Cleanups
 * core
   - inkern: fix a double unlock in iio_read_available_channel_raw when raw
   value doesn't appear to be raw (error path).
   - fixup accidental sizeof pointer in iio_device_add_mask_type.
 * docs
   - fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
 * tools
   - use local include/uapi headers to ensure always up to date.
   - increase length of allowed trigger names.
 * ad9834
   - symbolic to octal permissions.
 * ade7753
   - symbolic to octal permissions.
   - fix indentation
 * ade7754
   - symbolic to octal permissions.
 * ade7758
   - symbolic to octal permissions.
 - ade7854
   - symbolic to octal permissions.
 * as3935
   - move out of storm check to given consistent results for raw and processed
   values.
 * bmp280
   - fix bme280 naming in Kconfig help.
 * hi8435
   - avoid garbage on event after enable.
   - add missing in_voltage_sensing_mode_available to list possible enum options.
   - handle the reset gpio with the obvious polarity rather than relying on
   DT to provide it correctly.
 * hid-sensors
   - fix a wrong error path scrubbing of return values.
 * hid-sensors-accel
   - drop static on a local variable
 * hid-sensors-rotation
   - Add missing scale and offset property parsing support.
 * ina2xx
   - Fix a bad use of GENMASK and some typos and whitespace issues.
 * isl29018
   - only declare the ACPI table when ACPI is enabled.
 * isl29028
   - fix proximity sleep times.
 * lsm6dsx
   - replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
   dealing with the various PM config variables.
 * meson-saradc
   - mark meson_sar_adc_data static and const.
 * rcar-gyroadc
   - derive the interface clock speed from the fck clock on the basis they are
   the same actual clock.
   - drop the now unused if clock from the bindings.
 * rpr0521
   - disable sensor when marked as such rather than always enabling it.
   - poweroff if probe fails and we can talk to device.
   - make sure device powered off when it doesn't need to be on.
   - use sizeof rather than hardcoded size on value read.
   - whitespace fixup.
   - reorder channel numbers ready for buffered support which didn't quite
   make this pull request.
 * st-accel
   - fix platform data initialization to allow remove and reprobe.
 * st-pressure
   - fix platform data initialization to allow remove and reprobe.
 * tsl2x7x
   - S_IRUGO, S_IWUSR to octal values
   - rename driver for consistency with more recent drivers
   - drop FSF mailing address
   - replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
   relevant function renames.
 * zpa2326
   - report an error for consistency with other error paths.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlkjSHkRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FojDqQ//TVibBBZ0GgA+MwjIMDCpYL6CW4l+Et5v
 bD1EThc+qf3jv9kWbBz6WgySj9koZeF/hc0GN7x8XF57TeF/8sXhtbZKQ0za0Ouf
 uKAfYNi7jtdA4UEFawYrFUGIZtgQlbll/DKj7x2yDZtwIge9QF61fzPehGpq0u3b
 IiNlNFQSTKXOHi5tobMXXdBFL90m6kqDZM5ZwAWtQoSu1xQTjCsxu/LMJAJ3H7rU
 KEptEhc80kAvGqflOvw/HMaU7O7SXAhW3sQnXM2ksnDScGZ+zNzLcoca1YfM73rv
 x3vM/XL93A6CcRQkzFUC5vbtVVl00BMI7G3PQTGDOWWPgUPksLVIzfJR9GOqNmIJ
 W3HVwQbDZPvAbubvFHlUBa9ys4cbcmwU9214S57DvzVEt+cvpdujjIZ2Ulw3sVqN
 3xB1P9kNlcYvmBBu6LbP5GTDEu+VEETTjwj3osyimi56Zt44pJhoT68D46SD34Zw
 i3LCMFbbdJzEK4UWsvoBKFsTPipXgOntYDXaMZbULjtmJ6PEw0feubQIpMwtF5iw
 4fGk/1Q6l//rItJlXZE9PPiEBbXZ856lk/KQn+9vRABCrFni+7HWf6aDvkjf14o0
 8W+P/kAcXOPrToN2+NnAbIh7c9PLYmFWJa7DvDnQ5Guy0GStlxG18QEMNAhf39/0
 j/xopB1g8MI=
 =XLVY
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 4.13 cycle

Two entirely new drivers in here plus the usual range of cleanups and features.

New device support
* ad5064
  - add ltc2631, ltc2633 and ltc2635 support.
* bma180
  - trivial support for bma250e (new id)
* hid-sensor-rotation
  - add relative orientation and geometric orientation support.
* isl29028
  - add isl29030 support (its effectively the same part from a driver point of
  view)
* maxim_thermocouple
  - add max31856 id.
* meson-saradc
  - add meson8b SoC adc support.
* ti-adc084s021
  - new driver and bindings.
* ti-adc108s102
  - new driver and bindings.

Staging graduations
* isl29028

Features
* bma180
  - ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
  - add raw access rather than only events.
* hid-sensor-hub
  - Implement batch mode in which we can set a threshold on the amount of time
  between data coming from the fifos.  This is the first device to do this
  rather than use a watershed on the number of samples.
* hts221
  - power management support
* lsm6dsx
  - add system power management support.
* rpr0521
  - sampling frequency read / write
* stm32-trigger
  - add support for TRG02 triggers.
* tsl2583
  - runtime power management support.

Cleanups
* core
  - inkern: fix a double unlock in iio_read_available_channel_raw when raw
  value doesn't appear to be raw (error path).
  - fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
  - fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
  - use local include/uapi headers to ensure always up to date.
  - increase length of allowed trigger names.
* ad9834
  - symbolic to octal permissions.
* ade7753
  - symbolic to octal permissions.
  - fix indentation
* ade7754
  - symbolic to octal permissions.
* ade7758
  - symbolic to octal permissions.
- ade7854
  - symbolic to octal permissions.
* as3935
  - move out of storm check to given consistent results for raw and processed
  values.
* bmp280
  - fix bme280 naming in Kconfig help.
* hi8435
  - avoid garbage on event after enable.
  - add missing in_voltage_sensing_mode_available to list possible enum options.
  - handle the reset gpio with the obvious polarity rather than relying on
  DT to provide it correctly.
* hid-sensors
  - fix a wrong error path scrubbing of return values.
* hid-sensors-accel
  - drop static on a local variable
* hid-sensors-rotation
  - Add missing scale and offset property parsing support.
* ina2xx
  - Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
  - only declare the ACPI table when ACPI is enabled.
* isl29028
  - fix proximity sleep times.
* lsm6dsx
  - replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
  dealing with the various PM config variables.
* meson-saradc
  - mark meson_sar_adc_data static and const.
* rcar-gyroadc
  - derive the interface clock speed from the fck clock on the basis they are
  the same actual clock.
  - drop the now unused if clock from the bindings.
* rpr0521
  - disable sensor when marked as such rather than always enabling it.
  - poweroff if probe fails and we can talk to device.
  - make sure device powered off when it doesn't need to be on.
  - use sizeof rather than hardcoded size on value read.
  - whitespace fixup.
  - reorder channel numbers ready for buffered support which didn't quite
  make this pull request.
* st-accel
  - fix platform data initialization to allow remove and reprobe.
* st-pressure
  - fix platform data initialization to allow remove and reprobe.
* tsl2x7x
  - S_IRUGO, S_IWUSR to octal values
  - rename driver for consistency with more recent drivers
  - drop FSF mailing address
  - replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
  relevant function renames.
* zpa2326
  - report an error for consistency with other error paths.
2017-05-29 15:53:42 +02:00
Jan Kiszka 7e87d11c9b iio: adc: Add support for TI ADC108S102 and ADC128S102
This is an upstream port of an IIO driver for the TI ADC108S102 and
ADC128S102. The former can be found on the Intel Galileo Gen2 and the
Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
included.

Due to the lack of regulators under ACPI, we hard-code the voltage
provided to the VA pin of the ADC to 5 V, the value used on Galileo and
IOT2000. For DT usage, the regulator "vref-supply" provides this
information. Note that DT usage has not been tested.

Original author: Bogdan Pricop <bogdan.pricop@emutex.com>
Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
Todor Minchev <todor@minchev.co.uk>.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-05-21 15:11:14 +01:00
Mårten Lindahl 3691e5a694 iio: adc: add driver for the ti-adc084s021 chip
This adds support for the Texas Instruments ADC084S021 ADC chip.

Signed-off-by: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-05-14 16:34:11 +01:00
Linus Torvalds c6a677c6f3 Staging/IIO patches for 4.12-rc1
Here is the big staging tree update for 4.12-rc1.  And it's a big one,
 adding about 350k new lines of crap^Wcode, mostly all in a big dump of
 media drivers from Intel.  But there's other new drivers in here as
 well, yet-another-wifi driver, new IIO drivers, and a new crypto
 accelerator.  We also deleted a bunch of stuff, mostly in patch
 cleanups, but also the Android ION code has shrunk a lot, and the
 Android low memory killer driver was finally deleted, much to the
 celebration of the -mm developers.
 
 All of these have been in linux-next with a few build issues that will
 show up when you merge to your tree, I'll follow up with fixes for those
 after this gets merged.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQzzlQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ylNMgCcD+GoaF/Ml7YnULRl2GG/526II78AnitZ8qjd
 rPqeowMIewYu9fgckLUc
 =7rzO
 -----END PGP SIGNATURE-----

Merge tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging/IIO updates from Greg KH:
 "Here is the big staging tree update for 4.12-rc1.

  It's a big one, adding about 350k new lines of crap^Wcode, mostly all
  in a big dump of media drivers from Intel. But there's other new
  drivers in here as well, yet-another-wifi driver, new IIO drivers, and
  a new crypto accelerator.

  We also deleted a bunch of stuff, mostly in patch cleanups, but also
  the Android ION code has shrunk a lot, and the Android low memory
  killer driver was finally deleted, much to the celebration of the -mm
  developers.

  All of these have been in linux-next with a few build issues that will
  show up when you merge to your tree"

Merge conflicts in the new rtl8723bs driver (due to the wifi changes
this merge window) handled as per linux-next, courtesy of Stephen
Rothwell.

* tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1182 commits)
  staging: fsl-mc/dpio: add cpu <--> LE conversion for dpaa2_fd
  staging: ks7010: remove line continuations in quoted strings
  staging: vt6656: use tabs instead of spaces
  staging: android: ion: Fix unnecessary initialization of static variable
  staging: media: atomisp: fix range checking on clk_num
  staging: media: atomisp: fix misspelled word in comment
  staging: media: atomisp: kmap() can't fail
  staging: atomisp: remove #ifdef for runtime PM functions
  staging: atomisp: satm include directory is gone
  atomisp: remove some more unused files
  atomisp: remove hmm_load/store/clear indirections
  atomisp: kill off mmgr_free
  atomisp: clean up the hmm init/cleanup indirections
  atomisp: handle allocation calls before init in the hmm layer
  staging: fsl-dpaa2/eth: Add maintainer for Ethernet driver
  staging: fsl-dpaa2/eth: Add TODO file
  staging: fsl-dpaa2/eth: Add trace points
  staging: fsl-dpaa2/eth: Add driver specific stats
  staging: fsl-dpaa2/eth: Add ethtool support
  staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver
  ...
2017-05-05 18:16:23 -07:00
Quentin Schulz 0e34d5de96 iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs
The X-Powers AXP20X and AXP22X PMICs have multiple ADCs. They expose the
battery voltage, battery charge and discharge currents, AC-in and VBUS
voltages and currents, 2 GPIOs muxable in ADC mode and PMIC temperature.

This adds support for most of AXP20X and AXP22X ADCs.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-04-27 09:25:07 +01:00
Akinobu Mita a9e9c7153e iio: adc: add max1117/max1118/max1119 ADC driver
This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.

This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.

1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1.  The chip select line must be brought
high and low again without transfer.

2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete.  The conversion
begins with the falling edge of the chip select.  During the conversion
process, SCLK is ignored.

These two usages are unusual.  But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)

On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work.  But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-14 15:09:06 +01:00
Linus Walleij 63c3ecd946 iio: adc: add a driver for Qualcomm PM8xxx HK/XOADC
The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).

As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.

This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.

Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:42:26 +01:00
Linus Walleij e932d4f041 iio: adc: break out common code from SPMI VADC
The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.

As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:40:49 +01:00
Quentin Schulz 808a8b7377 iio: adc: sun4i-gpadc-iio: add support for A33 thermal sensor
This adds support for the Allwinner A33 thermal sensor.

Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.

The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.

Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).

The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:35:47 +01:00
Jacopo Mondi 69780a3bbc iio: adc: Add Maxim max9611 ADC driver
Add iio driver for Maxim max9611 and max9612 current-sense amplifiers
with 12-bits ADC interface.

Datasheet publicly available at:
https://datasheets.maximintegrated.com/en/ds/MAX9611-MAX9612.pdf

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-08 17:26:06 +01:00
Arnd Bergmann be2d732086 iio: adc: sun4i: add THERMAL dependency
With CONFIG_THERMAL=m and CONFIG_SUN4I_GPADC=y, we get a link error
from calling devm_thermal_zone_of_sensor_register:

drivers/iio/built-in.o: In function `sun4i_gpadc_probe':
:(.text+0x1c284): undefined reference to `devm_thermal_zone_of_sensor_register'

This adds a Kconfig dependency to ensure we can only have the ADC
driver as built-in when this function is also built-in, or when
we see the empty stub implementation. When the thermal code is
a module, we can still build the adc driver as a module, too.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-02 11:36:27 +01:00
Michael Hennerich bc82222fcc iio:adc: Driver for Linear Technology LTC2497 ADC
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-02 10:56:59 +01:00
Rick Altherr 573803234e iio: Aspeed ADC
Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold
interrupts are supported by the hardware but are not currently implemented.

Signed-off-by: Rick Altherr <raltherr@google.com>
Tested-by: Xo Wang <xow@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-01 11:53:20 +01:00
Tony Lindgren 25ec249632 iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC
On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.

Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.

Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-03-30 19:25:23 +01:00
Ksenija Stanojevic 0d690cc41b iio: adc: mxs-lradc: Remove driver
Since the driver has been split into MFD there is no reason for it to
stay, so remove it.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-23 12:29:01 +00:00
Ksenija Stanojevic 6dd112b9f8 iio: adc: mxs-lradc: Add support for ADC driver
Add support for sixteen-channel 12-bit resolution ADC and its functions,
which include general-purpose ADC readings, battery voltage measurement,
and die temperature measurement.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-23 12:28:43 +00:00
William Breathitt Gray 3c1de602f6 iio: pc104: Mask PC/104 drivers via the PC104 Kconfig option
PC/104 drivers should be hidden on machines which do not support PC/104
devices. This patch adds the PC104 Kconfig option as a dependency for
the relevant PC/104 device driver Kconfig options.

Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-03-15 21:59:08 +00:00
Quentin Schulz d1caa99055 iio: adc: add support for Allwinner SoCs ADC
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. This patch adds the ADC driver which is
based on the MFD for the same SoCs ADC.

This also registers the thermal adc channel in the iio map array so
iio_hwmon could use it without modifying the Device Tree. This registers
the driver in the thermal framework.

The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, this driver is capable of not registering the thermal sensor in
the thermal framework and thus, "quicken" the ADC readings.

This driver probes on three different platform_device_id to take into
account slight differences (registers bit and temperature computation)
between Allwinner SoCs ADCs.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-03-08 20:27:25 +00:00
Jonathan Cameron 0097e20e77 staging:iio:adc:lpc32xx Move out of staging.
There are a few more little cleanups that could be done on this driver, but
I don't think any are sufficient to justify not moving it out of staging.

It's a very simple driver (presumably for a simple part) so not much that can
go wrong.  I think it was only ever in staging because that's where IIO was
as a whole at the time and then we forgot about it!

Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-02-11 11:19:25 +00:00
Jonathan Cameron af8f651b39 staging:iio:adc:spear Move out of staging.
There are some unanswered questions due to disagreements between the code
and various datasheets (including between different datasheets for the same
part).

I don't think that is necessarily a reason to keep it in staging however.
I'm partly posting this patch inorder to reignite debate and with a bit
of luck find someone who has one of these to test!

Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-02-11 11:17:33 +00:00
Fabrice Gasnier 2763ea0585 iio: adc: stm32: add optional dma support
Add DMA optional support to STM32 ADC, as there is a limited number DMA
channels (request lines) that can be assigned to ADC. This way, driver
may fall back using interrupts when all DMA channels are in use for
other IPs.
Use dma cyclic mode with two periods. Allow to tune period length by
using watermark. Coherent memory is used for dma (max buffer size is
fixed to PAGE_SIZE).

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-29 12:49:17 +00:00
Fabrice Gasnier f24a33b3e2 iio: adc: stm32: Enable use of stm32 timer triggers
STM32 ADC has external timer trigger sources. Use stm32 timer triggers
API (e.g. is_stm32_timer_trigger()) with local ADC lookup table to
validate a trigger can be used.
This also provides correct trigger selection value (e.g. extsel).

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-28 18:24:12 +00:00
Fabrice Gasnier da9b948514 iio: adc: stm32: add support for triggered buffer mode
STM32 ADC conversions can be launched using hardware triggers.
It can be used to start conversion sequences (group of channels).
Selected channels are select via sequence registers.
Trigger source is selected via 'extsel' (external trigger mux).
Trigger polarity is set to rising edge by default.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-28 18:23:46 +00:00
Martin Blumenstingl 3adbf34273 iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs
This adds support for the SAR (Successive Approximation Register) ADC
on the Amlogic Meson SoCs.

The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets (see [0] and [1]), as well as by reading (various versions
of) the vendor driver and by inspecting the registers on the vendor
kernels of my testing-hardware.

Currently the GXBB, GXL and GXM SoCs are supported. GXBB hardware has
10-bit ADC resolution, while GXL and GXM have 12-bit ADC resolution.
The code was written to support older SoCs (Meson8 and Meson8b) as well,
but due to lack of actual testing-hardware no of_device_id was added for
these.

Two "features" from the vendor driver are currently missing:
- the vendor driver uses channel #7 for calibration (this improves the
  accuracy of the results - in my tests the results were less than 3%
  off without calibration compared to the vendor driver). Adding support
  for this should be easy, but is not required for most applications.
- channel #6 is connected to the SoCs internal temperature sensor.
  Adding support for this is probably not so easy since (based on the
  u-boot sources) most SoC versions are using different registers and
  algorithms for the conversion from "ADC value" to temperature.

Supported by the hardware but currently not supported by the driver:
- reading multiple channels at the same time (the hardware has a FIFO
  buffer which stores multiple results)
- continuous sampling (this would require a way to enable this
  individually because otherwise the ADC would be drawing power
  constantly)
- interrupt support (similar to the vendor driver this new driver is
  polling the results. It is unclear if the IRQ-mode is supported on
  older (Meson6 or Meson8) hardware as well or if there are any errata)

[0]
http://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
[1] http://dn.odroid.com/S905/DataSheet/S905_Public_Datasheet_V1.1.4.pdf

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-28 12:29:50 +00:00
Marek Vasut 059c53b323 iio: adc: Add Renesas GyroADC driver
Add IIO driver for the Renesas RCar GyroADC block. This block is a
simple 4/8-channel ADC which samples 12/15/24 bits of data every
cycle from all channels.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-28 11:33:53 +00:00
Greg Kroah-Hartman 08cad739ba Second round of IIO new device support, cleanups and features for the 4.11 cycle
New device support:
 * lsm6dsx imu
   - new driver and bindings.
 * max11100 adc
   - new driver and bindings.
 * tlc4541
   - new driver
 * tmp007 thermopile
   - new driver.
 
 Core
 * in kernel interfaces
   - pass through raw values if no scaling provided and a processed value is
     requested.
 * trigger
   - close a race condition in acquiring trigger reference.
   - constify device_type structures.
   - rework the viio_trigger_alloc function to be much neater and easier to
   read.
   - free trigger resources correctly on some error paths. Avoids putting a
   module we don't have.
 
 Documentation
 * ABI
   - specify a unit for proximity measurements.
 
 Cleanups and features
 * ads1015
   - constify iio_info structure.
 * ads7950 cleanups following merge in previous pull
   - Add device tree bindings
   - Drop the ti prefix from the module name in common with other drivers.
   - Change regulator name to vref to match datasheet and other drivers.
 * ak8974
   - remove a redundant zero timeout check.
 * bmi160
   - use variable names for sizeof instead of types.
 * cm3605
   - mark PM functions as __maybe_unused to avoid a build warning.
 * isl29028 (on it's way towards moving out of staging).
   - alignment fixes and newline improvements.
   - combine proxim_get and read_proxim for simpler code.
   - drop unused ISL29028_DEV_ATTR macro
   - move some error logging into functions to cut out repitition.
   - make error messages more consistent.
   - tidy up some brackets.
   - drop the enable flag that nothing uses.
   - only set proximity rate and ALS scale when relevant channel type is enabled.
   - runtime pm support.
 * lsm6dsx
   - fix wrong values for gyro sensitivitiy.
 * mag3110
   - claim direct mode during sysfs reads to avoid a race condition.
 * max1363
   - export OF device table IDs as module aliases.
 * max30100
   - use msleep for long uncritical delays.
 * mcp4531
   - export OF device table as module aliases.
 * ms5611
   - claim direct mode during sysfs reads to avoid a race condition.
 * opt3001
   - export OF device table as module aliases.
 * sx9500
   - claim direct mode during oversampling changes to avoid a race condition.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAliFK5sRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FoixSQ/+PrWf4PWdYSy+YlxxVzWMkJ3QhHYvDxpz
 mmH5GmsUB0RGi205VqAsvEF55Gcp5tzMYPXkjoxD1nXtuZ8sbVzkTSvrEGIqgA8b
 QUDdu76ntzJYWHVqouh8SywCJJbR/ssjZbIMzHvpYL/pty7+ICnaevauQf6n93Hh
 51yaPdtDNu4hq/lQdUz0QySGn9UJG7HUUKIfSDgZCh9q8VcQ8bmCf8MaRilJTzo9
 q8ONaziyB77w07JVeQLR/W8WO+KCRor0qqlokNtGDNAE2EOre6ul64Ded6TXLEez
 9ag/IYkECN3tImuHHJ9AKlCPOl39viZeP6sjvJc4glujZ0WKVuT76tlVP5XknuCE
 myy74d9Jt5/N43SYiQpRRm4Eadje56kCZtZhFidhRaEV74eQaOYG6fMNJ9Q/HJ4B
 d9Ykw7ZjU08DDOdQNtfQ5DGH72bKu94DSImqjmxXskUL6quZbxCnKPvI/vm//9xb
 7jSHtORTT8WxX/Ut9MTE59S0FS5x/8ivNxWxzqLDS0phcA4e1cLXJyFh0npxxYeu
 XdvJb+BefcfsPNbhhPl/anz577TJPTgNL4P2j1ano0duVCNV33p3y9Z2YNCkgaI1
 PtRVCBzMhaV60EQGBzBheNmN1+jeGu7q8o3UDhaoc4sX4ILut0oDE4PIDROmuItc
 QPLTmZkG20o=
 =Wvje
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-next

Jonathan writes:

Second round of IIO new device support, cleanups and features for the 4.11 cycle

New device support:
* lsm6dsx imu
  - new driver and bindings.
* max11100 adc
  - new driver and bindings.
* tlc4541
  - new driver
* tmp007 thermopile
  - new driver.

Core
* in kernel interfaces
  - pass through raw values if no scaling provided and a processed value is
    requested.
* trigger
  - close a race condition in acquiring trigger reference.
  - constify device_type structures.
  - rework the viio_trigger_alloc function to be much neater and easier to
  read.
  - free trigger resources correctly on some error paths. Avoids putting a
  module we don't have.

Documentation
* ABI
  - specify a unit for proximity measurements.

Cleanups and features
* ads1015
  - constify iio_info structure.
* ads7950 cleanups following merge in previous pull
  - Add device tree bindings
  - Drop the ti prefix from the module name in common with other drivers.
  - Change regulator name to vref to match datasheet and other drivers.
* ak8974
  - remove a redundant zero timeout check.
* bmi160
  - use variable names for sizeof instead of types.
* cm3605
  - mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
  - alignment fixes and newline improvements.
  - combine proxim_get and read_proxim for simpler code.
  - drop unused ISL29028_DEV_ATTR macro
  - move some error logging into functions to cut out repitition.
  - make error messages more consistent.
  - tidy up some brackets.
  - drop the enable flag that nothing uses.
  - only set proximity rate and ALS scale when relevant channel type is enabled.
  - runtime pm support.
* lsm6dsx
  - fix wrong values for gyro sensitivitiy.
* mag3110
  - claim direct mode during sysfs reads to avoid a race condition.
* max1363
  - export OF device table IDs as module aliases.
* max30100
  - use msleep for long uncritical delays.
* mcp4531
  - export OF device table as module aliases.
* ms5611
  - claim direct mode during sysfs reads to avoid a race condition.
* opt3001
  - export OF device table as module aliases.
* sx9500
  - claim direct mode during oversampling changes to avoid a race condition.
2017-01-23 09:23:23 +01:00
Phil Reid ac2bec9d58 iio: adc: tlc4541: add support for TI tlc4541 adc
This adds TI's tlc4541 16-bit ADC driver. Which is a single channel
ADC. Supports raw and trigger buffer access.
Also supports the tlc3541 14-bit device, which has not been tested.
Implementation of the tlc3541 is fairly straight forward thou.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-22 13:21:28 +00:00
Jacopo Mondi a8e7e88df9 iio: adc: Add Maxim MAX11100 driver
Add iio driver for Maxim MAX11100 single-channel ADC.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-21 13:16:38 +00:00
Greg Kroah-Hartman 4463c3e72d First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
 
 New device support
 * ads7950
   - new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
   ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
 * cm3605
   - New driver for this light sensor and proximity sensor  which is an
   analog part with some additional digital controls.
 * hx711
   - New driver.
 
 Core new stuff
 * Gravity sensor type.  This is a processed datastream in which the device
 will try to work out which way is down.
 * Split the buffer.h file into two parts. One provides the interface to 'use'
 a buffer, the second provides the internals of the buffer functionality as
 needed by implementations of buffers.
   - Move documentation inline so as to allow use of private: tag when
   generating documentation.
   - Add some utility functions for the few things that are directly done
   with the buffers.
   - Stop exporting functions that no-one uses outside of the core code.
   - Push docs down by the code in the c file where they should have always
   been.
   - Fix typo in kernel-doc for buffer.
   - push down some includes that were previously happening implicitly.
   - stop enabling the timestamp of the dummy device.
 
 Features and cleanups
 * ad5592r
   - ACPI support
 * ad5593r
   -ACPI support.
 * ad5933
   - Fix a false comment about size of a particular register.
 * ad7150
   - replace S_IRUGO | S_IWUSR with 0644.  I'm not that keen on these patches
   in general, but as it was nicely presented I took this one anyway. As a
   general rule will only take these as part of a larger driver cleanup.
   - don't eat an error but rather reutnr it in the write_event_config callback.
 * ad7606
   - replace non standard range attibute with _scale
 * ade7753
   - use usleep_range for short sleeps
 * ade7754
   - use usleep_range for short sleeps
 * ade7758
   - use usleep_range for short sleeps
 * ade7759
   - use usleep_range for short sleeps
 * ade7854
   - use usleep_range for short sleeps
 * adis16201
   - fix description
 * adis16203
   - fix description
   - fix copyright year
 * adis16209
   - fix description
 * adt7316
   - Add braces to arms of if else statement (for consistency)
   - Alignment fixes.
 * axp288
   - Fix up an issue with accidental overwrites of data.
 * bmi160
   - add deivce tables for i2c and spi to support correctly identifying the
   full dt name (including manufacturer).
   - device tree binding.
 * bmp280
   - use usleep_range for short sleeps.
 * cm3232
   - return error from cm3232_reg_init rather than eating it if the last write
   fails.
 * dummy driver
   - remove a semicolor found at end of a function defintition.
 * exynos-adc
   - use usleep_range for short sleeps.
 * hid-sensor (accel)
   - Add timestamp support.  The hardware can provide timestamps so lets support
   them. If not fall back to timestamps estimated in kernel.
 * hid-sensor (light)
   - Add a duplicate ID for the light channels so as to keep existing interface
   whilst also using the more standard IIO interface.
 * hts221
   - acpi probing
 * imx25-gcq
   - Add a macro call to allow this driver to be automatically loaded.
 * isl29028
   - reorganise code to avoid deep nesting of if statements.
   - move chip test and default regs into a function suitable or sharing with
   power management code.
   - tidy up some code alignment.
 * lidar-lite-v3
   - introduce compatible strings that make it clear Garmin have consideral
   friends.
 * mma8452
   - avoid returning signed value when unsigned is appropriate
 * spmi-vadc
   - Update function for generic voltage conversion to take into account that
   different channels on this device should be handled differently.
   - Rework code to allow per channel voltage scaling and support the standard
   options for this hardware.
   - Fixup three minor issues with the above patches for this part. These all
   effect test builds rather than the native builds for the part, but good to
   clean them up anyway.
 * st_sensors
   - support device matching from the ACPI DST tables.
   - acpi based probing for accelerometers
   - acpi based probing for pressure sensors
   - Allow pressure sensors to read negative values.
   - Export sampling frequency for lps25h and lps331ap.
   - Add support for the old DT bindings from the period when these deivces
   were often supported through windows.
 
 Docs fixup:
 * typo in sysfs-bus-iio
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlh2bhcRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FogdSQ/9Hyd3ic5AgWyDKr9JI1vJPj3kT0PIYHLk
 4ucbQ8HUJQBBLnsausTb+UwuGV277DkVjGVsI4epn59H3CvkNh3Egl3XCmbhIpt2
 oyl9Pw9dSon6n/7I5pNSwmqD45O+aB7qFLigIfLmciwpMHZly3ExzGBMpqUkgjf9
 bVzndDqrfoNIrU7UaMD6QgrSxrgYJJJJwBDig/0zjAkGvu9L8a8ghrKkrRzMy62O
 nGP5mmEagivFF9lpGzzrw2pYBQWY4AFbsNvuLElE7nUz0PKKG+9J0oaBiglTYv2p
 mkNlYl7iTZfI3eFOXa+7HdSmeNhYX2dvbEM2jAA/Mr6ojWg2mSRu7Y19Kl2KP7K7
 BDRKBw+Cp0wkVvJ8LU/6PiDSmqp09VfjjqevzVGJi/BmWLzG0Mi2OsQmmynbw2SV
 hxiGETRV7vBoyJWDJuwJoftZaRnHWJbiQ6ftEUbWOFA9RIBMgOJBiL+RtxerJkHv
 FWlCFpv/618TUB/uM15+EOLVJAT5b7K+6+l6EGEjWdjiS/7vL7QM5DL8w4zV43zz
 cQ98UeIlqCkvoFmx9uHbl44COLQgzNtxAjytLxqbsOmEb40wlzoNzgSoUGu73SaG
 8qwznH0w0p8P1nyzwe9qKKK6SmFhj/tF6jKVmIi/H7wJdA1J5dAAmwFUBSxLs2DX
 u1eM3ikCl/M=
 =yjUA
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First round of new device support, features and cleanups for IIO in the 4.11 cycle.

It's shaping to be another fairly busy cycle. Lots more on the way!

New device support
* ads7950
  - new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
  ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
  - New driver for this light sensor and proximity sensor  which is an
  analog part with some additional digital controls.
* hx711
  - New driver.

Core new stuff
* Gravity sensor type.  This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
  - Move documentation inline so as to allow use of private: tag when
  generating documentation.
  - Add some utility functions for the few things that are directly done
  with the buffers.
  - Stop exporting functions that no-one uses outside of the core code.
  - Push docs down by the code in the c file where they should have always
  been.
  - Fix typo in kernel-doc for buffer.
  - push down some includes that were previously happening implicitly.
  - stop enabling the timestamp of the dummy device.

Features and cleanups
* ad5592r
  - ACPI support
* ad5593r
  -ACPI support.
* ad5933
  - Fix a false comment about size of a particular register.
* ad7150
  - replace S_IRUGO | S_IWUSR with 0644.  I'm not that keen on these patches
  in general, but as it was nicely presented I took this one anyway. As a
  general rule will only take these as part of a larger driver cleanup.
  - don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
  - replace non standard range attibute with _scale
* ade7753
  - use usleep_range for short sleeps
* ade7754
  - use usleep_range for short sleeps
* ade7758
  - use usleep_range for short sleeps
* ade7759
  - use usleep_range for short sleeps
* ade7854
  - use usleep_range for short sleeps
* adis16201
  - fix description
* adis16203
  - fix description
  - fix copyright year
* adis16209
  - fix description
* adt7316
  - Add braces to arms of if else statement (for consistency)
  - Alignment fixes.
* axp288
  - Fix up an issue with accidental overwrites of data.
* bmi160
  - add deivce tables for i2c and spi to support correctly identifying the
  full dt name (including manufacturer).
  - device tree binding.
* bmp280
  - use usleep_range for short sleeps.
* cm3232
  - return error from cm3232_reg_init rather than eating it if the last write
  fails.
* dummy driver
  - remove a semicolor found at end of a function defintition.
* exynos-adc
  - use usleep_range for short sleeps.
* hid-sensor (accel)
  - Add timestamp support.  The hardware can provide timestamps so lets support
  them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
  - Add a duplicate ID for the light channels so as to keep existing interface
  whilst also using the more standard IIO interface.
* hts221
  - acpi probing
* imx25-gcq
  - Add a macro call to allow this driver to be automatically loaded.
* isl29028
  - reorganise code to avoid deep nesting of if statements.
  - move chip test and default regs into a function suitable or sharing with
  power management code.
  - tidy up some code alignment.
* lidar-lite-v3
  - introduce compatible strings that make it clear Garmin have consideral
  friends.
* mma8452
  - avoid returning signed value when unsigned is appropriate
* spmi-vadc
  - Update function for generic voltage conversion to take into account that
  different channels on this device should be handled differently.
  - Rework code to allow per channel voltage scaling and support the standard
  options for this hardware.
  - Fixup three minor issues with the above patches for this part. These all
  effect test builds rather than the native builds for the part, but good to
  clean them up anyway.
* st_sensors
  - support device matching from the ACPI DST tables.
  - acpi based probing for accelerometers
  - acpi based probing for pressure sensors
  - Allow pressure sensors to read negative values.
  - Export sampling frequency for lps25h and lps331ap.
  - Add support for the old DT bindings from the period when these deivces
  were often supported through windows.

Docs fixup:
* typo in sysfs-bus-iio
2017-01-19 10:40:44 +01:00
Andreas Klinger c3b2fdd0ea iio: adc: hx711: Add IIO driver for AVIA HX711
This is the IIO driver for AVIA HX711 ADC which is mostly used in weighting
cells.

The protocol is quite simple and using GPIOs:
One GPIO is used as clock (SCK) while another GPIO is read (DOUT)

The raw value read from the chip is delivered.
To get a weight one needs to subtract the zero offset and scale it.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-10 19:54:59 +00:00
Geert Uytterhoeven b1448ea9cd iio: adc: TI_AM335X_ADC should depend on HAS_DMA
If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/iio/adc/ti_am335x_adc.ko] undefined!

Add a dependency on HAS_DMA to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: f438b9da (" drivers: iio: ti_am335x_adc: add dma support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-12-30 16:37:48 +00:00
David Lechner 902c4b2446 iio: adc: New driver for TI ADS7950 chips
This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-12-03 09:57:21 +00:00
Fabrice Gasnier 0f883b223a iio: adc: Add support for STM32 ADC
This patch adds support for STMicroelectronics STM32 MCU's analog to
digital converter.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-11-19 12:18:33 +00:00
Fabrice Gasnier 1add698802 iio: adc: Add support for STM32 ADC core
Add core driver for STMicroelectronics STM32 ADC (Analog to Digital
Converter). STM32 ADC can be composed of up to 3 ADCs with shared
resources like clock prescaler, common interrupt line and analog
reference voltage.
This core driver basically manages shared resources.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-11-19 12:17:45 +00:00
Peter Rosin b475f80b35 iio: envelope-detector: ADC driver based on a DAC and a comparator
The DAC is used to find the peak level of an alternating voltage input
signal by a binary search using the output of a comparator wired to
an interrupt pin. Like so:
                          _
                         | \
    input +------>-------|+ \
                         |   \
           .-------.     |    }---.
           |       |     |   /    |
           |    dac|-->--|- /     |
           |       |     |_/      |
           |       |              |
           |       |              |
           |    irq|------<-------'
           |       |
           '-------'

Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-11-13 13:07:17 +00:00
Greg Kroah-Hartman bdc065666a Merge 4.9-rc3 into staging-next
This resolves a merge issue with
drivers/staging/iio/accel/sca3000_core.c and we want the fixes all in
here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-30 06:38:44 -04:00
Akinobu Mita 815bbc8746 iio: ti-adc0832: add triggered buffer support
This adds triggered buffer support for the ti-adc0832 driver.  Tested with
ADC0831 and ADC0832 by using SYSFS trigger.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-10-23 19:34:25 +01:00
Mika Westerberg 2967999fbc iio: adc: ti-adc081c: Select IIO_TRIGGERED_BUFFER to prevent build errors
Commit 08e05d1fce ("ti-adc081c: Initial triggered buffer support") added
triggered buffer support but that also requires CONFIG_IIO_TRIGGERED_BUFFER,
otherwise we get errors from linker such as:

  drivers/built-in.o: In function `adc081c_remove':
  drivers/iio/adc/ti-adc081c.c:225: undefined reference to `iio_triggered_buffer_cleanup'

Fix these by explicitly selecting both CONFIG_IIO_TRIGGERED_BUFFER and
CONFIG_IIO_BUFFER in Kconfig for the driver.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-10-09 08:45:07 +01:00
Lars-Peter Clausen aa16c6bd0e iio:adc: Add support for AD7766/AD7767
Add support for the AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1, AD7767-2
Analog to Digital converters. It's a family of single channel 24-bit SAR
ADCs. They are all digital interface compatible and the main difference is
the internal decimation rate and analog performance. For communication with
the host processor a SPI interface is used.

In addition the part has a data ready pin that is pulsed for one MCLK cycle
when a conversion has completed and can be used as a IIO trigger.

Datasheets:
	http://www.analog.com/media/en/technical-documentation/data-sheets/AD7766.pdf
	http://www.analog.com/media/en/technical-documentation/data-sheets/AD7767.pdf

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-09-27 20:33:01 +01:00
Greg Kroah-Hartman 552edf8d79 Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
 * ad8801 dac
   - new driver supporting ad8801 and ad8803 DACs.
 * adc12138
   - new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
 * ltc2485 adc
   - new driver
 * mxc6255
   - add support for the mxc6225 part name and fixup the ID check so it works.
 * vz89x VOC sensor
   - add support for the vz89te part which drops the voc_short channel and adds
     CRCs compared to other supported parts.
 
 New features
 * core
   - immutable triggers.  These effectively grant exclusive control over a
     trigger. The typical usecase is a device representing an analog part
     (perhaps a MUX) that needs to control the sampling of a downstream
     ADC.
   - resource managed trigger registration and triggered_buffer_init.
   - iio_push_event now protected against case of the event interface
     registration not having yet occured.  Only matters if an interrupt
     can occur during this window - might happen on shared interrupt lines.
   - helper to let a driver query if the trigger it is using is provided by
     itself (using the convention of both device and trigger having the same
     parent).
 * tools
   - iio-utils. Used channel modifier scaling in preference to generic scaling
     when both exist.
 * at91-adc
   - Add support for touchscreen switches closure time needed by some newer
     parts.
 * stx104
   - support the ADC channels on this ADC/DAC board. As these are the primary
     feature of the board also move the driver to the iio/adc directory.
 * sx9500
   - device tree bindings.
 
 Cleanups / Fixes
 * ad5755
   - fix an off-by-one on devnr limit check (introduced earlier this cycle)
 * ad7266
   - drop NULL check on devm_regulator_get_optional as it can't return NULL.
 * ak8974
   - avoid an unused functional warning due to rework in PM core code.
   - remove .owner field setting as done by i2c_core.
 * ina2xx
   - clear out a left over debug field from chip global data.
 * hid-sensors
   - avoid an unused functional warning due to rework in PM core code.
 * maxim-thermocouple
   - fix non static symbol warnings.
 * ms5611
   - fetch and enable regulators unconditionally when they aren't optional.
 * sca3000
   - whitespace cleanup.
 * st_sensors
   - fetch and enable regulators unconditionally rather than having them
     supported as optional regulators (missunderstanding on my part amongst
     others a while back)
   - followup to previous patch fixes error checking on the regulators.
   - mark symbols static where possible.
   - use the 'is it my trigger' help function.  This prevents the odd case
     of another device triggering from the st-sensors trigger whilst the
     st-sensors trigger is itself not using it but rather using say an hrtimer.
 * ti-ads1015
   - add missing of_node_put.
 * vz89x
   - rework to all support of new devices.
   - prevent reading of a corrupted buffer.
   - fixup a return value of 0/1 in a bool returning function.
 
 Address updates
 - Vlad Dogaru email address change.
 -----BEGIN PGP SIGNATURE-----
 
 iQIuBAABCAAYBQJX1wW9ERxqaWMyM0BrZXJuZWwub3JnAAoJEFSFNJnE9BaII9UP
 /jXkXtaL62pvipMuEujmpR7j/A+GhmSWHhnbJ9XXeGZStGMUummTyaM+6WZoCKUH
 bMtZh/ETsn+FI7mD7P/FtwHauoxSmndcaAfB6cDKQMVakbXbz4VHrim256cY3gvq
 dzF5nYX+wDue6D7k55VPrtV1isBfipeCXKBtzBlAXaVE2FK2qKP+PIlAln8Ql5/l
 b5B3pvqu0YVED4t2MzyVWcVidPOEh9GgwHu7Ba+kjVi6zuB4w+r5ZreIObb5IR54
 FDcEwL6vV9AlmX15Pc18NO+50bZ8TvgT4y7ISqaOwszaIEoDAc0hXT7TdUOscmtt
 LIbhzHVMVkPSjxvtpz2ui8GfqzhxLi3ZzfNHRegOqH4b2Cpoh4zdwn7nCyJEHZV5
 simAL00FGjzp6B4Zp+Ly6ygKzpF3iXZce0Qjlr/ge+ioNIrfuK10sdLw8NZA5GUB
 JcFYijcFLUb0Cu/KjZ7njlfdAN9Tt94xzpnllM8+j4M50Nhbw05YNhIxB7RxmeSH
 Y44/oBLG51SgtlIg5Z4rULRAcOC5dty73Inb0n4lbN/pjgIcnh+EYtPeI2fA8vyB
 XYqr4xx+A3ZX1yKpYLYO+JYtVsVq9RGYdb501uBhEE3/GWEpxZvbyqHnPwwfM+Pf
 ZNuBceBxM3yyi4Z/lKkZnQbaF/1fFoG7FO1n6iRpb8Ci
 =V1xL
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of iio new device support, features and cleanups for the 4.9 cycle.

New device support
* ad8801 dac
  - new driver supporting ad8801 and ad8803 DACs.
* adc12138
  - new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
  - new driver
* mxc6255
  - add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
  - add support for the vz89te part which drops the voc_short channel and adds
    CRCs compared to other supported parts.

New features
* core
  - immutable triggers.  These effectively grant exclusive control over a
    trigger. The typical usecase is a device representing an analog part
    (perhaps a MUX) that needs to control the sampling of a downstream
    ADC.
  - resource managed trigger registration and triggered_buffer_init.
  - iio_push_event now protected against case of the event interface
    registration not having yet occured.  Only matters if an interrupt
    can occur during this window - might happen on shared interrupt lines.
  - helper to let a driver query if the trigger it is using is provided by
    itself (using the convention of both device and trigger having the same
    parent).
* tools
  - iio-utils. Used channel modifier scaling in preference to generic scaling
    when both exist.
* at91-adc
  - Add support for touchscreen switches closure time needed by some newer
    parts.
* stx104
  - support the ADC channels on this ADC/DAC board. As these are the primary
    feature of the board also move the driver to the iio/adc directory.
* sx9500
  - device tree bindings.

Cleanups / Fixes
* ad5755
  - fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
  - drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
  - avoid an unused functional warning due to rework in PM core code.
  - remove .owner field setting as done by i2c_core.
* ina2xx
  - clear out a left over debug field from chip global data.
* hid-sensors
  - avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
  - fix non static symbol warnings.
* ms5611
  - fetch and enable regulators unconditionally when they aren't optional.
* sca3000
  - whitespace cleanup.
* st_sensors
  - fetch and enable regulators unconditionally rather than having them
    supported as optional regulators (missunderstanding on my part amongst
    others a while back)
  - followup to previous patch fixes error checking on the regulators.
  - mark symbols static where possible.
  - use the 'is it my trigger' help function.  This prevents the odd case
    of another device triggering from the st-sensors trigger whilst the
    st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
  - add missing of_node_put.
* vz89x
  - rework to all support of new devices.
  - prevent reading of a corrupted buffer.
  - fixup a return value of 0/1 in a bool returning function.

Address updates
- Vlad Dogaru email address change.
2016-09-14 20:42:03 +02:00
Greg Kroah-Hartman 9c2edd8b5b Merge 4.8-rc5 into staging-next
We want the staging fixes in here as well to handle merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-05 08:13:24 +02:00