This patch contains r8a7779 SMP support V3 - now including
CPU hotplug offine and online support. The r8a7779 power
domain code is tied together with SMP glue code which allows
us to control the power domains via CPU hotplug.
At this point the kernel boots with the 4 Cortex-A9 cores in
SMP mode and all CPU cores except CPU0 can be hotplugged.
The code in platsmp.c is quite far from pretty, but it is
kept like that intentionally to avoid creating layers of
code that will go away in the near future anyway. The code
needs to be updated when some per-SoC handling code will be
added to the ARM architecture, see the following patch for
more information:
"[RFC PATCH 0/3] Per SoC descriptor"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add power domain control support for the r8a7779 SoC V2.
This adds support for 4 power domains for I/O Devices
together with code that can be used for CPU cores as well.
The only out of the ordinary experience is the need for
ioremap() of SYSC registers. Because of that we need to
execute some init function before setting up the domains.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add r8a7779 PFC function support using the shared PFC code.
Depends on variable bitfield config register patches.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add cache flushing code to the SH-Mobile specific CPU hotplug
implementation. While at it, add a cpu mask to make sure the
cache flushing code is finished in platform_cpu_die() before
letting the SoC-specific code in shmobile_platform_cpu_kill()
proceed with turning off power.
Without this code CPU hotplug offline fails when cache is
enabled on Cortex-A9 based SoCs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the function shmobile_platform_kill_cpu() to allow
SoC specific code to tie in their CPU shutdown code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the low level SMP assembly code for SH-Mobile ARM
from using the INIT to the CPUINIT section. This unbreaks
onlining of CPUs using the CPU hotplug interface:
echo 1 > /sys/devices/system/cpu/cpu1/online
Without this fix the reset vector code used by CPU hotplug
will be freed as init section data and CPU cores cannot
be brought online.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SCIF2 and SCIF4 pin configuration code to
the r8a7779 Marzen board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add GPIO-only r8a7779 PFC support V2.
Only regular GPIOs are supported at this time. GPIO_FN are not
supported because they require variable bit width support in be
the shared pfc code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initial support for the r8a7779 SoC and the Marzen board (V2).
Only SCIF ports and the TMU are supported at this point.
To keep things simple only entity-mapped virt-to-phys mappings
are supported. This forces drivers and other SoC glue code to
make use of ioremap(). We cannot support early serial console
due to virtual address space collisions with the ARM kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
The 158MiB memory area was used to support HD
resolution multimedia workloads using the same
legacy memory allocating solution as on SH.
There are no in-tree kernel dependencies on the
158MiB setting, and future development should
reserve and allocate memory using some other
method like for instance CMA.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
* pm-domains:
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
PM / Domains: Provide an always on power domain governor
PM / Domains: Fix default system suspend/resume operations
PM / Domains: Make it possible to assign names to generic PM domains
PM / Domains: fix compilation failure for CONFIG_PM_GENERIC_DOMAINS unset
PM / Domains: Automatically update overoptimistic latency information
PM / Domains: Add default power off governor function (v4)
PM / Domains: Add device stop governor function (v4)
PM / Domains: Rework system suspend callback routines (v2)
PM / Domains: Introduce "save/restore state" device callbacks
PM / Domains: Make it possible to use per-device domain callbacks
After adding PM QoS constraints for the I2C controller in the A4R
domain, that domain can be allowed to be turned off and on by runtime
PM, so remove the "always on" governor from it.
However, the A4R domain has to be "on" when suspend_device_irqs() and
resume_device_irqs() are executed during system suspend and resume,
respectively, so that those functions don't crash while accessing the
INTCS. For this reason, add a PM notifier to the SH7372 PM code and
make it restore power to A4R before system suspend and remove power
from all unused PM domains after system resume.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
SH7372 uses two independent mechanisms for ensuring that power
domains will never be turned off: the stay_on flag and the "always
on" domain governor. Moreover, the "always on" governor is only taken
into accout by runtime PM code paths, while the stay_on flag affects
all attempts to turn the given domain off. Thus setting the stay_on
flag causes the "always on" governor to be unnecessary, which is
quite confusing.
However, the stay_on flag is currently only set for two domains: A3SP
and A4S. Moreover, it only is set for the A3SP domain if
console_suspend_enabled is set, so stay_on won't be necessary for
that domain any more if console_suspend_enabled is checked directly
in its .suspend() routine. [This requires domain .suspend() to
return a result, but that is a minor modification.] Analogously,
stay_on won't be necessary for the A4S domain if it's .suspend()
routine always returns an error code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Since the SH7372's INTCS in included into syscore suspend/resume,
which causes the chip to be accessed when PM domains have been
turned off during system suspend, the A4R domain containing the
INTCS has to stay on during system sleep, which is suboptimal
from the power consumption point of view.
For this reason, add a new INTC flag, skip_syscore_suspend, to mark
the INTCS for intc_suspend() and intc_resume(), so that they don't
touch it. This allows the A4R domain to be turned off during
system suspend and the INTCS state is resrored during system
resume by the A4R's "power on" code.
Suggested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The sh7372 contains a power domain named A4S which in turn
contains power domains for both I/O Devices and CPU cores.
At this point only System wide Suspend-to-RAM is supported,
but the the hardware can also support CPUIdle. With more
efforts in the future CPUIdle can work with bot A4S and A3SM.
Tested on the sh7372 Mackerel board.
[rjw: Rebased on top of the current linux-pm tree.]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add default value for CONFIG_ARCH_NR_GPIO to Kconfig and remove the
definition in gpio.h.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Saves a tiny amount of code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a name member pointer to struct generic_pm_domain and use it in
diagnostic messages regarding the domain power-off and power-on
latencies. Update the ARM shmobile SH7372 code to assign names to
the PM domains used by it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Current div6 clocks can specify their current parent clocks
from its register value if it is registered
by sh_clk_div6_reparent_register().
This patch modifies all div6 clocks into SH_CLK_DIV6_EXT().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a function deciding whether or not devices should be stopped in
pm_genpd_runtime_suspend() depending on their PM QoS constraints
and stop/start timing values. Make it possible to add information
used by this function to device objects.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The current generic PM domains code requires that the same .stop(),
.start() and .active_wakeup() device callback routines be used for
all devices in the given domain, which is inflexible and may not
cover some specific use cases. For this reason, make it possible to
use device specific .start()/.stop() and .active_wakeup() callback
routines by adding corresponding callback pointers to struct
generic_pm_domain_data. Add a new helper routine,
pm_genpd_register_callbacks(), that can be used to populate
the new per-device callback pointers.
Modify the shmobile's power domains code to allow drivers to add
their own code to be run during the device stop and start operations
with the help of the new callback pointers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Current fsi-ak4642 was using id_entry name in order to specify
FSI port and ak464x codec.
But it was no sense, no flexibility.
Platform can specify FSI/ak464x pair by this patch.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Keep the ZB clock enabled on sh73a0 to allow the BSC
to access external peripherals hooked up to CS signals.
This is needed to unbreak Ethernet support on sh73a0 boards
such as AG5EVM and Kota2 together with the following patch:
794d78f drivers: sh: late disabling of clocks V2
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix IRQ support on the AG5EVM board. The sh73a0 and the AG5EVM
board make use of the ARM GIC hardware block as main interrupt
controller. The following commit changed the default behaviour
for non-device tree platforms and broke AG5EVM irq support:
f37a53c ARM: gic: fix irq_alloc_descs handling for sparse irq
Without this fix the following warning triggers at boot:
NR_IRQS:1024 nr_irqs:1024 1024
------------[ cut here ]------------
WARNING: at arch/arm/common/gic.c:607 gic_init+0x90/0x2e4()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
[<c000c868>] (unwind_backtrace+0x0/0xe0) from [<c001857c>] (warn_slowpath_commo)
[<c001857c>] (warn_slowpath_common+0x48/0x60) from [<c00185d8>] (warn_slowpath_)
[<c00185d8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c029ee08>] (gic_init+0x90/0x2)
[<c029ee08>] (gic_init+0x90/0x2e4) from [<c029f278>] (sh73a0_init_irq+0x30/0x18)
[<c029f278>] (sh73a0_init_irq+0x30/0x184) from [<c029c0b4>] (init_IRQ+0x14/0x1c)
[<c029c0b4>] (init_IRQ+0x14/0x1c) from [<c029a5cc>] (start_kernel+0x15c/0x2b8)
[<c029a5cc>] (start_kernel+0x15c/0x2b8) from [<4000803c>] (0x4000803c)
---[ end trace 1b75b31a2719ed1c ]---
With this fix applied interrupts work as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Kota2 board support code to
use the recently merged TPU LED driver whenever
possible.
The sh73a0 SoC has 5 TPU hardware blocks each with
4 timer channels which in theory allows a total of
20 LEDs to be controlled by "leds-renesas-tpu"
driver instances. The Kota2 board has 4 LEDs connected
to GPIO pins that also come with TPU pin functions, so
this patch ties up these 4 LEDS and leaves the remaining
3 LEDS for the GPIO based LED driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix IRQ support on the Kota2 board. The sh73a0 and the Kota2
board make use of the ARM GIC hardware block as main interrupt
controller. The following commit changed the default behaviour
for non-device tree platforms and broke Kota2 irq support:
f37a53c ARM: gic: fix irq_alloc_descs handling for sparse irq
Without this fix the following warning triggers at boot:
NR_IRQS:1024 nr_irqs:1024 1024
------------[ cut here ]------------
WARNING: at arch/arm/common/gic.c:607 gic_init+0x90/0x2e4()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
[<c000c868>] (unwind_backtrace+0x0/0xe0) from [<c001857c>] (warn_slowpath_commo)
[<c001857c>] (warn_slowpath_common+0x48/0x60) from [<c00185d8>] (warn_slowpath_)
[<c00185d8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c029ee08>] (gic_init+0x90/0x2)
[<c029ee08>] (gic_init+0x90/0x2e4) from [<c029f278>] (sh73a0_init_irq+0x30/0x18)
[<c029f278>] (sh73a0_init_irq+0x30/0x184) from [<c029c0b4>] (init_IRQ+0x14/0x1c)
[<c029c0b4>] (init_IRQ+0x14/0x1c) from [<c029a5cc>] (start_kernel+0x15c/0x2b8)
[<c029a5cc>] (start_kernel+0x15c/0x2b8) from [<4000803c>] (0x4000803c)
---[ end trace 1b75b31a2719ed1c ]---
With this fix applied interrupts work as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support PINT on sh73a0 and Kota2 using INTC PINT macros.
With this patch applied the Kota2 ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
sh73a0 PINT support is included in 3.2-rc but the Kota2 board
code does not make use of this shared code base without this
patch. Without this patch kota2 on-board ethernet is broken.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some clocks can select its parent clock by CPG register.
But it might have been modified by boot-loader or something.
This patch removed fixed initial parent clock,
and setup it from their current register settings.
It works on div6 reparent clocks for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dot clock of SH MIPI are depends on each platform board.
This patch adds set_dot_clock() function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI DSI can use 0-4 lane
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
dsipck clock is controled by CLKDEV_ICK_ID() in clock-shxxx.
dsi0p_clk/dsi1p_clk naming is not needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Krzysztof Ha■asa <khc@pm.waw.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
Fix build regression introduced by commit 056879d2f2
(ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix) by moving
the intialization of the A3SP domain to a separate function and
providing an empty definition of it for CONFIG_PM unset.
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Convert the SMP shmobile platforms to use gic_handle_irq() instead
of the assembly macro.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Even when CONFIG_MULTI_IRQ_HANDLER is selected, the core code
requires the arch_irq_handler_default macro to be defined as
a fallback.
It turns out nobody is using that particular feature as both PXA
and shmobile have all their machine descriptors populated with
the interrupt handler, leaving unused code (or empty macros) in
their entry-macro.S file just to be able to compile entry-armv.S.
Make CONFIG_MULTI_IRQ_HANDLER exclusive wrt arch_irq_handler_default,
which allows to remove one test from the hot path. Also cleanup both
PXA and shmobile entry-macro.S.
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The SH7372 PM domain initialization routine calls pd_power_up()
that executes the domain's .resume() callback, if present, and for
the A4R domain this callback attepmts to restore the INTCS state from
uninitialized data. To avoid that, introduce __pd_power_up() that
will only execute the domain's .resume() callback if its second
argument is 'true' and make the SH7372 PM domain initialization
use it with 'false' as its second argument. Redefine pd_power_up()
as a wrapper around __pd_power_up().
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tracked-down-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
bonito board needs some settings by pmic which use i2c access.
It is dependent on the device to be used.
This patch adds standard settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
devices enable/disable are controled by dip-switch on bonito board.
If bonito core board is connected to base board,
you can check the settings from FPGA.
This patch adds basic code and controls SCIFA5 settings
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R8A7740 GIC can not get external IRQx interrupt directly
without GIC - INTC demux support.
Current AG5 is using GIC - INTCS demux with
special irq relocation. but GIC - INTCA demux
is still not supported and it needs irq number re-mapping.
OTOH, normal INTC support as before is very enough for R8A7740,
because it is not SMP CPU.
This patch adds INTCA/INTCS support instead of GIC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds I2C support to r8a7740 CPU
which has lasting errata on I2C I/O pad reset.
This patch is including work-around.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds PFC support for the R8A7740 (R-Mobile A1) CPU
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the R8A7740 (R-Mobile A1) CPU
Timer, serial, gic, clock are supported at this point.
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states
e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.
Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If "no_suspend_irq" is used on the sh7372 Mackerel board
with v3.2-rc1 then Suspend-to-RAM fails because the serial
console tries to write to the SCIF driver even though the
power domain is turned off.
This patch checks the state of "console_suspend_enabled"
to see if A3SP should be forced enabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Don't skip debugging output upon earlier loop termination in pd_power_up().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'rmobile-latest' of git://github.com/pmundt/linux-sh: (21 commits)
ARM: mach-shmobile: ag5evm needs CONFIG_I2C
ARM: mach-shmobile: sh73a0 and AG5EVM PINT support
ARM: mach-shmobile: Add support for PINT though INTC macros
ARM: mach-shmobile: SDHI0 GPIO hotplug for AG5EVM
ARM: mach-shmobile: Use common INTC IRQ code on sh73a0
ARM: mach-shmobile: Use common INTC IRQ code on sh7372
ARM: mach-shmobile: Use common INTC IRQ code on sh7377
ARM: mach-shmobile: Use common INTC IRQ code on sh7367
ARM: mach-shmobile: sh73a0 GPIO IRQ support
ARM: sh7372 ap4evb NOR Flash USB boot fix
ARM: mach-shmobile: sh7372 Mackerel NOR Flash USB boot fix
sh: intc: Allow triggering on both edges for ARM SoCs
ARM: mach-shmobile: Break out INTC IRQ code
ARM: mach-shmobile: Kota2 SDHI0 and SDHI1 support
ARM: mach-shmobile: Kota2 SCIFA4 and SCIFB support
ARM: mach-shmobile: Kota2 MMCIF support
ARM: mach-shmobile: Kota2 GPIO LEDs support
ARM: mach-shmobile: Kota2 GPIO Keys support
ARM: mach-shmobile: Kota2 KEYSC support
ARM: mach-shmobile: Kota2 SCIFA2 and SMSC911X support
...
ag5evm implements a backlight control, using an I2C controller, therefore
it needs CONFIG_I2C to fix this make failure
arch/arm/mach-shmobile/built-in.o: In function `lcd_on':
pfc-sh73a0.c:(.text+0x2334): undefined reference to `i2c_get_adapter'
pfc-sh73a0.c:(.text+0x2370): undefined reference to `i2c_transfer'
(ignore pfc-sh73a0.c) and to build successfully.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support PINT on sh73a0 and AG5EVM using INTC PINT macros.
With this patch applied the AG5EVM ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a INTC_PINT() macro with various helper bits to allow SoCs
like sh73a0 to suppor the PINT hardware using regular INTC tables.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Implement GPIO hotplugging via TMIO_MMC_HAS_COLD_CD for
AG5EVM SDHI0. This is possible now when INTCA is used for
IRQ triggering on sh73a0. Without INTCA IRQ support we are
left with the GIC hardware block that does not support
dealing with active low interrupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve IRQ triggering support by making use of the macro
INTC_IRQ_PINS_32() for INTCA on sh73a0. Unfortunately it
is not as easy as just using the macro as-is, we need to
do mask and unmaks in the GIC but configure other bits
and ack in INTCA. Update GPIO IRQ mappings while at it.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh73a0 GPIO IRQs by making use
of the PFC GPIO IRQ feature. Only IRQ pins are supported
at this time. In the future when PINT interrupts also are
supported properly we can easily extend the table with such
information. Also, the sh73a0 is currently making use of
the GIC for external interrupt which is rather unflexible
when it comes to triggering configuration at this point.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on ap4evb.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on Mackerel.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add INTC_IRQ_PINS_16() and INTC_IRQ_PINS_32() to mach/intc.h.
These macros define 16 or 32 external IRQ pins on a certain
memory base address. Can be used with INTCA or INTCS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
The sh_mobile_ceu_camera driver has been converted to use the V4L2
subdevice .[gs]_mbus_config() operations, therefore we don't need
SOCAM_* flags for the soc_camera_platform driver anymore. Remove
them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prepare the board to switch to the new subdevice media-bus configuration
operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sh_mobile_csi2 driver will change meaning of the .lanes platform
data field from "bitmask of used lanes" to "number of used lanes."
To avoid a regression during this transition switch ap4evb to rely
on the 2 lane default.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'next/cross-platform' of git://git.linaro.org/people/arnd/arm-soc:
arm/imx: use Kconfig choice for low-level debug UART selection
ARM: realview: use Kconfig choice for debug UART selection
ARM: plat-samsung: use Kconfig choice for debug UART selection
ARM: versatile: convert logical CPU numbers to physical numbers
ARM: ux500: convert logical CPU numbers to physical numbers
ARM: shmobile: convert logical CPU numbers to physical numbers
ARM: msm: convert logical CPU numbers to physical numbers
ARM: exynos4: convert logical CPU numbers to physical numbers
Fix up trivial conflict (config DEBUG_S3C_UART move/split vs addition of
ARM_KPROBES_TEST option) in arch/arm/Kconfig.debug
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
video: platinumfb: Add __devexit_p at necessary place
drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
drivers/video: fsl-diu-fb: remove unused panel operating mode support
drivers/video: fsl-diu-fb: use an enum for the AOI index
drivers/video: fsl-diu-fb: add several new video modes
drivers/video: fsl-diu-fb: remove broken screen blanking support
drivers/video: fsl-diu-fb: move some definitions out of the header file
drivers/video: fsl-diu-fb: fix some ioctls
video: da8xx-fb: Increased resolution configuration of revised LCDC IP
OMAPDSS: picodlp: add missing #include <linux/module.h>
fb: fix au1100fb bitrot.
mx3fb: fix NULL pointer dereference in screen blanking.
video: irq: Remove IRQF_DISABLED
smscufx: change edid data to u8 instead of char
OMAPDSS: DISPC: zorder support for DSS overlays
OMAPDSS: DISPC: VIDEO3 pipeline support
OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
video/omap: fix build dependencies
...
Fix up conflicts in:
- drivers/staging/xgifb/XGI_main_26.c
Changes to XGIfb_pan_var()
- drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
Removed (or in the case of apollon.c, merged into the generic
DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
This allows specific (non-multiplexed) IRQ handlers to be used.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
PPI handling is a bit of an odd beast. It uses its own low level
handling code and is hardwired to the local timers (hence lacking
a registration interface).
Instead, switch the low handling to the normal SPI handling code.
PPIs are handled by the handle_percpu_devid_irq flow.
This also allows the removal of some duplicated code.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: David Brown <davidb@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This change adds support for the sh7372 A4R power domain.
The sh7372 A4R hardware power domain contains the
SH CPU Core and a set of I/O devices including
multimedia accelerators and I2C controllers.
One special case about A4R is the INTCS interrupt
controller that needs to be saved and restored to
keep working as expected. Also the LCDC hardware
blocks are in a different hardware power domain
but have their IRQs routed only through INTCS. So
as long as LCDCs are active we cannot power down
INTCS because that would risk losing interrupts.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This change adds support for the sh7372 A3SP power domain.
The sh7372 A3SP hardware power domain contains a
wide range of I/O devices. The list of I/O devices
include SCIF serial ports, DMA Engine hardware,
SD and MMC controller hardware, USB controllers
and I2C master controllers.
This patch adds the A3SP low level code which
powers the hardware power domain on and off. It
also ties in platform devices to the pm domain
support code.
It is worth noting that the serial console is
hooked up to SCIFA0 on most sh7372 boards, and
the SCIFA0 port is included in the A3SP hardware
power domain. For this reason we cannot output
debug messages from the low level power control
code in the case of A3SP.
QoS support is needed in drivers before we can
enable the A3SP power control on the fly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead. This allows the
nr_cpus command line option to work as expected.
Cc: <stable@kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch uses the new cpu_logical_map() macro for converting logical
CPU numbers into physical numbers when dealing with the SCU in the SMP
boot path for sh73a0.
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Merge commit e8b364b88c
(PM / Clocks: Do not acquire a mutex under a spinlock) fixing
a regression in drivers/base/power/clock_ops.c.
Conflicts:
drivers/base/power/clock_ops.c
Update the sh7372 sleep code to build parts of the
code only when SUSPEND and/or CPU_IDLE are set.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds sh7372 A3SM power domain support.
The sh7372 A3SM hardware power domain contains the
ARM Cortex-A8 CPU Core including L2 cache. This
sleep mode can be seen as a one step deeper sleep
mode from the already existing Core Standby mode.
To wake up from A3SM sleep only a few wakeup sources
are supported - so the regular INTC controller will
not be able to help us unfortunately.
The code in this patch will enter A3SM sleep via the
regular Suspend-to-RAM interface in the case of only
wakeups supported by A3SM are enabled. If unsupported
wakeups are enabled then Core Standby will be used
instead.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Convert the sh7372 Core Standby code to make use
of the new generic ARM cpu suspend/resume code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add SDHI0 and SDHI1 support to the Kota2 board.
SDHI0 is hooked up to a microSD card slot and SDHI1
to a wireless module that also connects to SCIFB.
This depends on the recently merged code for
TMIO_MMC_HAS_IDLE_WAIT together with PFC support
for pull-ups on SDHI0 and SDHI1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SCIFA4 and SCIFB support to the Kota2 board.
Only pins are configured since the SCIF platform
devices are already present in the sh73a0 code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for sh73a0 MMCIF hardware block on the
Kota2 board. A non-removable eMMC chip is used with
8 data bits on the MMC bus.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch ties in GPIO LEDs support on the Kota2
board. For now all LEDs are driven by the GPIO LED
driver, but in the not so distant future the LEDs
hooked up to TPU pin functions will be moved over
to the recently posted LED TPU driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch ties in GPIO Keys support on the Kota2
board. For now the keys are used in polling mode,
but after extending the sh73a0 PFC with IRQ support
we should be able to switch to the IRQ driven driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kota2 base board support including the on-chip SCIFA2
serial console and the on-board SMSC911X ethernet port.
The s73a0 SMP bits are also updated to include Kota2.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock control support for sh7372 CMT hardware blocks.
No upstream sh7372 boards are making use of CMT3 + CMT4,
but the sh7372 hardware happens to come out of reset with
all CMT MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock control support for sh7372 MSIOF hardware blocks.
No upstream sh7372 boards are making use of MSIOF0->2,
but the sh7372 hardware happens to come out of reset with
all MSIOF MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
USB-DMAC1 needs SMSTPCR4/MSTP407 controls, not MSTP214
this patch tested on mackerel board
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the existing sh73a0 PFC code with pull-ups for
SDHI0 and SDHI2. Without this patch only SDHI1 has
pull-up support on sh73a0. Needed by boards that make
use of the internal pull-up resistor support built in
the SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes support for the SGX interrupt source in
the sh7372 INTCS controller.
The SGX hardware block included in sh7372 is already hooked
up to the ARM Cortex-A8 core using the INTCA controller,
so SGX users are encouraged to make use of that interrupt
source instead.
Removing support for the SGX interrupt source in INTCS
simplifies the sh7372 power management code by allowing
us to assume that only INTCA needs to be powered on to
operate the SGX hardware.
If the INTCS interrupt source would be kept then the kernel
would be forced to deal with additional dependencies that does
not follow the regular power domain hiearachy. With this
patch in place we can safely power down INTCS while the
SGX is operating.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>