Fix IRQ support on the Kota2 board. The sh73a0 and the Kota2
board make use of the ARM GIC hardware block as main interrupt
controller. The following commit changed the default behaviour
for non-device tree platforms and broke Kota2 irq support:
f37a53c ARM: gic: fix irq_alloc_descs handling for sparse irq
Without this fix the following warning triggers at boot:
NR_IRQS:1024 nr_irqs:1024 1024
------------[ cut here ]------------
WARNING: at arch/arm/common/gic.c:607 gic_init+0x90/0x2e4()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
[<c000c868>] (unwind_backtrace+0x0/0xe0) from [<c001857c>] (warn_slowpath_commo)
[<c001857c>] (warn_slowpath_common+0x48/0x60) from [<c00185d8>] (warn_slowpath_)
[<c00185d8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c029ee08>] (gic_init+0x90/0x2)
[<c029ee08>] (gic_init+0x90/0x2e4) from [<c029f278>] (sh73a0_init_irq+0x30/0x18)
[<c029f278>] (sh73a0_init_irq+0x30/0x184) from [<c029c0b4>] (init_IRQ+0x14/0x1c)
[<c029c0b4>] (init_IRQ+0x14/0x1c) from [<c029a5cc>] (start_kernel+0x15c/0x2b8)
[<c029a5cc>] (start_kernel+0x15c/0x2b8) from [<4000803c>] (0x4000803c)
---[ end trace 1b75b31a2719ed1c ]---
With this fix applied interrupts work as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support PINT on sh73a0 and Kota2 using INTC PINT macros.
With this patch applied the Kota2 ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
sh73a0 PINT support is included in 3.2-rc but the Kota2 board
code does not make use of this shared code base without this
patch. Without this patch kota2 on-board ethernet is broken.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some clocks can select its parent clock by CPG register.
But it might have been modified by boot-loader or something.
This patch removed fixed initial parent clock,
and setup it from their current register settings.
It works on div6 reparent clocks for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dot clock of SH MIPI are depends on each platform board.
This patch adds set_dot_clock() function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI DSI can use 0-4 lane
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
dsipck clock is controled by CLKDEV_ICK_ID() in clock-shxxx.
dsi0p_clk/dsi1p_clk naming is not needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Krzysztof Ha■asa <khc@pm.waw.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
Fix build regression introduced by commit 056879d2f2
(ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix) by moving
the intialization of the A3SP domain to a separate function and
providing an empty definition of it for CONFIG_PM unset.
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Convert the SMP shmobile platforms to use gic_handle_irq() instead
of the assembly macro.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Even when CONFIG_MULTI_IRQ_HANDLER is selected, the core code
requires the arch_irq_handler_default macro to be defined as
a fallback.
It turns out nobody is using that particular feature as both PXA
and shmobile have all their machine descriptors populated with
the interrupt handler, leaving unused code (or empty macros) in
their entry-macro.S file just to be able to compile entry-armv.S.
Make CONFIG_MULTI_IRQ_HANDLER exclusive wrt arch_irq_handler_default,
which allows to remove one test from the hot path. Also cleanup both
PXA and shmobile entry-macro.S.
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The SH7372 PM domain initialization routine calls pd_power_up()
that executes the domain's .resume() callback, if present, and for
the A4R domain this callback attepmts to restore the INTCS state from
uninitialized data. To avoid that, introduce __pd_power_up() that
will only execute the domain's .resume() callback if its second
argument is 'true' and make the SH7372 PM domain initialization
use it with 'false' as its second argument. Redefine pd_power_up()
as a wrapper around __pd_power_up().
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tracked-down-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
bonito board needs some settings by pmic which use i2c access.
It is dependent on the device to be used.
This patch adds standard settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
devices enable/disable are controled by dip-switch on bonito board.
If bonito core board is connected to base board,
you can check the settings from FPGA.
This patch adds basic code and controls SCIFA5 settings
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R8A7740 GIC can not get external IRQx interrupt directly
without GIC - INTC demux support.
Current AG5 is using GIC - INTCS demux with
special irq relocation. but GIC - INTCA demux
is still not supported and it needs irq number re-mapping.
OTOH, normal INTC support as before is very enough for R8A7740,
because it is not SMP CPU.
This patch adds INTCA/INTCS support instead of GIC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds I2C support to r8a7740 CPU
which has lasting errata on I2C I/O pad reset.
This patch is including work-around.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds PFC support for the R8A7740 (R-Mobile A1) CPU
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the R8A7740 (R-Mobile A1) CPU
Timer, serial, gic, clock are supported at this point.
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states
e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.
Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If "no_suspend_irq" is used on the sh7372 Mackerel board
with v3.2-rc1 then Suspend-to-RAM fails because the serial
console tries to write to the SCIF driver even though the
power domain is turned off.
This patch checks the state of "console_suspend_enabled"
to see if A3SP should be forced enabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Don't skip debugging output upon earlier loop termination in pd_power_up().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'rmobile-latest' of git://github.com/pmundt/linux-sh: (21 commits)
ARM: mach-shmobile: ag5evm needs CONFIG_I2C
ARM: mach-shmobile: sh73a0 and AG5EVM PINT support
ARM: mach-shmobile: Add support for PINT though INTC macros
ARM: mach-shmobile: SDHI0 GPIO hotplug for AG5EVM
ARM: mach-shmobile: Use common INTC IRQ code on sh73a0
ARM: mach-shmobile: Use common INTC IRQ code on sh7372
ARM: mach-shmobile: Use common INTC IRQ code on sh7377
ARM: mach-shmobile: Use common INTC IRQ code on sh7367
ARM: mach-shmobile: sh73a0 GPIO IRQ support
ARM: sh7372 ap4evb NOR Flash USB boot fix
ARM: mach-shmobile: sh7372 Mackerel NOR Flash USB boot fix
sh: intc: Allow triggering on both edges for ARM SoCs
ARM: mach-shmobile: Break out INTC IRQ code
ARM: mach-shmobile: Kota2 SDHI0 and SDHI1 support
ARM: mach-shmobile: Kota2 SCIFA4 and SCIFB support
ARM: mach-shmobile: Kota2 MMCIF support
ARM: mach-shmobile: Kota2 GPIO LEDs support
ARM: mach-shmobile: Kota2 GPIO Keys support
ARM: mach-shmobile: Kota2 KEYSC support
ARM: mach-shmobile: Kota2 SCIFA2 and SMSC911X support
...
ag5evm implements a backlight control, using an I2C controller, therefore
it needs CONFIG_I2C to fix this make failure
arch/arm/mach-shmobile/built-in.o: In function `lcd_on':
pfc-sh73a0.c:(.text+0x2334): undefined reference to `i2c_get_adapter'
pfc-sh73a0.c:(.text+0x2370): undefined reference to `i2c_transfer'
(ignore pfc-sh73a0.c) and to build successfully.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support PINT on sh73a0 and AG5EVM using INTC PINT macros.
With this patch applied the AG5EVM ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a INTC_PINT() macro with various helper bits to allow SoCs
like sh73a0 to suppor the PINT hardware using regular INTC tables.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Implement GPIO hotplugging via TMIO_MMC_HAS_COLD_CD for
AG5EVM SDHI0. This is possible now when INTCA is used for
IRQ triggering on sh73a0. Without INTCA IRQ support we are
left with the GIC hardware block that does not support
dealing with active low interrupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve IRQ triggering support by making use of the macro
INTC_IRQ_PINS_32() for INTCA on sh73a0. Unfortunately it
is not as easy as just using the macro as-is, we need to
do mask and unmaks in the GIC but configure other bits
and ack in INTCA. Update GPIO IRQ mappings while at it.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh73a0 GPIO IRQs by making use
of the PFC GPIO IRQ feature. Only IRQ pins are supported
at this time. In the future when PINT interrupts also are
supported properly we can easily extend the table with such
information. Also, the sh73a0 is currently making use of
the GIC for external interrupt which is rather unflexible
when it comes to triggering configuration at this point.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on ap4evb.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on Mackerel.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add INTC_IRQ_PINS_16() and INTC_IRQ_PINS_32() to mach/intc.h.
These macros define 16 or 32 external IRQ pins on a certain
memory base address. Can be used with INTCA or INTCS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
The sh_mobile_ceu_camera driver has been converted to use the V4L2
subdevice .[gs]_mbus_config() operations, therefore we don't need
SOCAM_* flags for the soc_camera_platform driver anymore. Remove
them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prepare the board to switch to the new subdevice media-bus configuration
operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sh_mobile_csi2 driver will change meaning of the .lanes platform
data field from "bitmask of used lanes" to "number of used lanes."
To avoid a regression during this transition switch ap4evb to rely
on the 2 lane default.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'next/cross-platform' of git://git.linaro.org/people/arnd/arm-soc:
arm/imx: use Kconfig choice for low-level debug UART selection
ARM: realview: use Kconfig choice for debug UART selection
ARM: plat-samsung: use Kconfig choice for debug UART selection
ARM: versatile: convert logical CPU numbers to physical numbers
ARM: ux500: convert logical CPU numbers to physical numbers
ARM: shmobile: convert logical CPU numbers to physical numbers
ARM: msm: convert logical CPU numbers to physical numbers
ARM: exynos4: convert logical CPU numbers to physical numbers
Fix up trivial conflict (config DEBUG_S3C_UART move/split vs addition of
ARM_KPROBES_TEST option) in arch/arm/Kconfig.debug
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
video: platinumfb: Add __devexit_p at necessary place
drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
drivers/video: fsl-diu-fb: remove unused panel operating mode support
drivers/video: fsl-diu-fb: use an enum for the AOI index
drivers/video: fsl-diu-fb: add several new video modes
drivers/video: fsl-diu-fb: remove broken screen blanking support
drivers/video: fsl-diu-fb: move some definitions out of the header file
drivers/video: fsl-diu-fb: fix some ioctls
video: da8xx-fb: Increased resolution configuration of revised LCDC IP
OMAPDSS: picodlp: add missing #include <linux/module.h>
fb: fix au1100fb bitrot.
mx3fb: fix NULL pointer dereference in screen blanking.
video: irq: Remove IRQF_DISABLED
smscufx: change edid data to u8 instead of char
OMAPDSS: DISPC: zorder support for DSS overlays
OMAPDSS: DISPC: VIDEO3 pipeline support
OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
video/omap: fix build dependencies
...
Fix up conflicts in:
- drivers/staging/xgifb/XGI_main_26.c
Changes to XGIfb_pan_var()
- drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
Removed (or in the case of apollon.c, merged into the generic
DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
This allows specific (non-multiplexed) IRQ handlers to be used.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
PPI handling is a bit of an odd beast. It uses its own low level
handling code and is hardwired to the local timers (hence lacking
a registration interface).
Instead, switch the low handling to the normal SPI handling code.
PPIs are handled by the handle_percpu_devid_irq flow.
This also allows the removal of some duplicated code.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: David Brown <davidb@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This change adds support for the sh7372 A4R power domain.
The sh7372 A4R hardware power domain contains the
SH CPU Core and a set of I/O devices including
multimedia accelerators and I2C controllers.
One special case about A4R is the INTCS interrupt
controller that needs to be saved and restored to
keep working as expected. Also the LCDC hardware
blocks are in a different hardware power domain
but have their IRQs routed only through INTCS. So
as long as LCDCs are active we cannot power down
INTCS because that would risk losing interrupts.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This change adds support for the sh7372 A3SP power domain.
The sh7372 A3SP hardware power domain contains a
wide range of I/O devices. The list of I/O devices
include SCIF serial ports, DMA Engine hardware,
SD and MMC controller hardware, USB controllers
and I2C master controllers.
This patch adds the A3SP low level code which
powers the hardware power domain on and off. It
also ties in platform devices to the pm domain
support code.
It is worth noting that the serial console is
hooked up to SCIFA0 on most sh7372 boards, and
the SCIFA0 port is included in the A3SP hardware
power domain. For this reason we cannot output
debug messages from the low level power control
code in the case of A3SP.
QoS support is needed in drivers before we can
enable the A3SP power control on the fly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead. This allows the
nr_cpus command line option to work as expected.
Cc: <stable@kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch uses the new cpu_logical_map() macro for converting logical
CPU numbers into physical numbers when dealing with the SCU in the SMP
boot path for sh73a0.
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Merge commit e8b364b88c
(PM / Clocks: Do not acquire a mutex under a spinlock) fixing
a regression in drivers/base/power/clock_ops.c.
Conflicts:
drivers/base/power/clock_ops.c
Update the sh7372 sleep code to build parts of the
code only when SUSPEND and/or CPU_IDLE are set.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds sh7372 A3SM power domain support.
The sh7372 A3SM hardware power domain contains the
ARM Cortex-A8 CPU Core including L2 cache. This
sleep mode can be seen as a one step deeper sleep
mode from the already existing Core Standby mode.
To wake up from A3SM sleep only a few wakeup sources
are supported - so the regular INTC controller will
not be able to help us unfortunately.
The code in this patch will enter A3SM sleep via the
regular Suspend-to-RAM interface in the case of only
wakeups supported by A3SM are enabled. If unsupported
wakeups are enabled then Core Standby will be used
instead.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Convert the sh7372 Core Standby code to make use
of the new generic ARM cpu suspend/resume code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add SDHI0 and SDHI1 support to the Kota2 board.
SDHI0 is hooked up to a microSD card slot and SDHI1
to a wireless module that also connects to SCIFB.
This depends on the recently merged code for
TMIO_MMC_HAS_IDLE_WAIT together with PFC support
for pull-ups on SDHI0 and SDHI1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SCIFA4 and SCIFB support to the Kota2 board.
Only pins are configured since the SCIF platform
devices are already present in the sh73a0 code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for sh73a0 MMCIF hardware block on the
Kota2 board. A non-removable eMMC chip is used with
8 data bits on the MMC bus.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch ties in GPIO LEDs support on the Kota2
board. For now all LEDs are driven by the GPIO LED
driver, but in the not so distant future the LEDs
hooked up to TPU pin functions will be moved over
to the recently posted LED TPU driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch ties in GPIO Keys support on the Kota2
board. For now the keys are used in polling mode,
but after extending the sh73a0 PFC with IRQ support
we should be able to switch to the IRQ driven driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kota2 base board support including the on-chip SCIFA2
serial console and the on-board SMSC911X ethernet port.
The s73a0 SMP bits are also updated to include Kota2.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock control support for sh7372 CMT hardware blocks.
No upstream sh7372 boards are making use of CMT3 + CMT4,
but the sh7372 hardware happens to come out of reset with
all CMT MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock control support for sh7372 MSIOF hardware blocks.
No upstream sh7372 boards are making use of MSIOF0->2,
but the sh7372 hardware happens to come out of reset with
all MSIOF MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
USB-DMAC1 needs SMSTPCR4/MSTP407 controls, not MSTP214
this patch tested on mackerel board
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the existing sh73a0 PFC code with pull-ups for
SDHI0 and SDHI2. Without this patch only SDHI1 has
pull-up support on sh73a0. Needed by boards that make
use of the internal pull-up resistor support built in
the SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes support for the SGX interrupt source in
the sh7372 INTCS controller.
The SGX hardware block included in sh7372 is already hooked
up to the ARM Cortex-A8 core using the INTCA controller,
so SGX users are encouraged to make use of that interrupt
source instead.
Removing support for the SGX interrupt source in INTCS
simplifies the sh7372 power management code by allowing
us to assume that only INTCA needs to be powered on to
operate the SGX hardware.
If the INTCS interrupt source would be kept then the kernel
would be forced to deal with additional dependencies that does
not follow the regular power domain hiearachy. With this
patch in place we can safely power down INTCS while the
SGX is operating.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The generic PM domains framework currently doesn't work with devices
whose power.irq_safe flag is set, because runtime PM callbacks for
such devices are run with interrupts disabled and the callbacks
provided by the generic PM domains framework use domain mutexes
and may sleep. However, such devices very well may belong to
power domains on some systems, so the generic PM domains framework
should take them into account.
For this reason, modify the generic PM domains framework so that the
domain .power_off() and .power_on() callbacks are never executed for
a domain containing devices with power.irq_safe set, although the
.stop_device() and .start_device() callbacks are still run for them.
Additionally, introduce a flag allowing the creator of a
struct generic_pm_domain object to indicate that its .stop_device()
and .start_device() callbacks may be run in interrupt context
(might_sleep_if() triggers if that flag is not set and one of those
callbacks is run in interrupt context).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since the PM clock management code in drivers/base/power/clock_ops.c
is used for both runtime PM and system suspend/hibernation, the
definitions of data structures and headers related to it should not
be located in include/linux/pm_rumtime.h. Move them to a separate
header file.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently pm_genpd_runtime_resume() has to walk the list of devices
from the device's PM domain to find the corresponding device list
object containing the need_restore field to check if the driver's
.runtime_resume() callback should be executed for the device.
This is suboptimal and can be simplified by using power.sybsys_data
to store device information used by the generic PM domains code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce struct pm_subsys_data that may be subclassed by subsystems
to store subsystem-specific information related to the device. Move
the clock management fields accessed through the power.subsys_data
pointer in struct device to the new strucutre.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Instead of coding the undocumented dependencies between power domains
A3RV and A4LC on SH7372 directly into the low-level power up/down
routines, make A3RV be a subdomain of A4LC, which will cause the
same dependecies to hold.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Associate the HDMI clock together with LCDC1 on sh7372.
Without this patch Suspend-to-RAM hangs on the boards
AP4EVB and Mackerel. The code hangs in the LCDC driver
where the software is waiting forever for the hardware to
power down. By explicitly associating the HDMI clock with
LCDC1 we can make sure the HDMI clock is enabled using
Runtime PM whenever the driver is accessing the hardware.
This HDMI and LCDC1 dependency is documented in the sh7372
data sheet. Older kernels did work as expected but the
recently merged (3.1-rc)
794d78f drivers: sh: late disabling of clocks V2
introduced code to turn off clocks lacking software reference
which happens to include the HDMI clock that is needed by
LCDC1 to operate as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many of the gpio_to_irq implementations use the gpiolib version of this
function. Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish. Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h. This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: David Brown <davidb@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch use channel0 as Tx, and channel1 as Rx
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
Now that v4l2 subdevices have got their own device objects, having
one more device in soc-camera clients became redundant and confusing.
This patch removes those devices and the soc-camera bus, they used to
reside on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This moves us one more step closer to eliminating the soc-camera bus
and devices on it. Besides, as a side effect, CSI-2 runtime PM on
sh-mobile secomes finer grained now: we only have to power on the
interface, when the device nodes are open.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
The SDHI block on the ag5evm requires waiting for idle
before writing to some registers.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
Since the A4LC should only be powered off if the A3RV is off, make
the A4LC's power down routine return -EBUSY if A3RV is not off to
indicate to the core that it doesn't want to power off the domain in
that case. This will cause the core to regard A4LC as active, so
the pm_genpd_poweron() in pd_power_down_a3rv() is not necessary any
more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make pd_power_down_a3rv() use genpd_queue_power_off_work() to queue
up the powering off of the A4LC domain to avoid queuing it up when
it is pending.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make shmobile use pm_genpd_poweroff_unused() instead of the
open-coded powering off PM domains without devices in use.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make sure that the 'static' keywork is at the beginning of declaration
for arch/arm/mach-shmobile/board-ap4evb.c
This gets rid of warnings like
warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure that the 'static' keywork is at the beginning of declaration
for arch/arm/mach-shmobile/board-ap4evb.c
This gets rid of warnings like
warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Switch the sh7372 CPU support to use CMT2 instead
of CMT1 for system timer.
CMT1 is located in the A3SP power domain while CMT2
is located in the always-on power domain C5.
This improves our PM situation - with CMT2 as timer
we can power down A3SP and still access the timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a power domain workaround for the VPU and A3RV on sh7372.
The sh7372 data sheet mentions that the VPU is located in the
A3RV power domain. The A3RV power domain is not related to A4LC
in any way, but testing shows that unless A3RV _and_ A4LC are
powered on the VPU test program will bomb out.
This issue may be caused by a more or less undocumented dependency
on the MERAM block that happens to be located in A4LC. So now we
know that the out-of-reset requirement of the VPU is that the MERAM
is powered on.
This patch adds a workaround for A3RV to make sure A4LC is powered
on - this so we can use the VPU even though the LCDCs are in blanking
state and A4LC is supposed to be off.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add sh7372 specific code to power down unused pm domains.
This should really be replaced by some generic PM core
code IMO, but until that happens this patch makes sure
we don't waste power by leaving unused power domains on.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a mach-shmobile specific callback for SoC-specific code
to hook into. By having the late_initcall() in a common place
we can have multi-SoC/board support in the same kernel binary.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add support for the sh7372 D4 power domain. This power domain
contains the Coresight-ETM hardware block.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add support for the sh7372 A4MP power domain
and hook up the FSI/SPU2 device.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
FSI act as peripheral circuits of the SPU2.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If an ARM system has multiple cpus in the same socket and the
kernel is booted with maxcpus=1, secondary cpus are possible but
not present due to how platform_smp_prepare_cpus() is called.
Since most typical ARM processors don't actually support physical
hotplug, initialize the present map to be equal to the possible
map in generic ARM SMP code. Also, always call
platform_smp_prepare_cpus() as long as max_cpus is non-zero (0
means no SMP) to allow platform code to do any SMP setup.
After applying this patch it's possible to boot an ARM system
with maxcpus=1 on the command line and then hotplug in secondary
cpus via sysfs. This is more in line with how x86 does things.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the sh7372 A3SG power domain. This domain contains
the SGX hardware block, but there is no open source driver available.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add support for the sh7372 A3RI power domain. This domain contains
the ISP hardware block, but there is no driver available.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add support for the sh7372 A3RV power domain and hook
up the VPU device.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The AP4EVB board is also using a sh7372 SoC, so tie in
A4LC support on that board as well.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use the generic power domains support introduced by the previous
patch to implement support for power domains on SH7372.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
The common PM clock management functions may be used for system
suspend/resume as well as for runtime PM, so rename them
accordingly. Modify kerneldoc comments describing these functions
and kernel messages printed by them, so that they refer to power
management in general rather that to runtime PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
The naming convention used by commit 7538e3db6e015e890825fbd9f86599b
(PM: Add support for device power domains), which introduced the
struct dev_power_domain type for representing device power domains,
evidently confuses some developers who tend to think that objects
of this type must correspond to "power domains" as defined by
hardware, which is not the case. Namely, at the kernel level, a
struct dev_power_domain object can represent arbitrary set of devices
that are mutually dependent power management-wise and need not belong
to one hardware power domain. To avoid that confusion, rename struct
dev_power_domain to struct dev_pm_domain and rename the related
pointers in struct device and struct pm_clk_notifier_block from
pwr_domain to pm_domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
struct soc_camera_link imx074_link in board-ap4evb.c doesn't have
to be global.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows a ROM-able zImage to be written to eSD and for SuperH Mobile
ARM to boot directly from the SDHI hardware block.
This is achieved by the MaskROM loading the first portion of the image into
MERAM and then jumping to it. This portion contains loader code which
copies the entire image to SDRAM and jumps to it. From there the zImage
boot code proceeds as normal, uncompressing the image into its final
location and then jumping to it.
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Name the SDHI1 instance sh_sdhi1_info to be consistent with sh_sdhi0_info.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
USB1 can use IRQ interrupt and notify function for usbhs driver,
but USB0 is using polling for it.
The priority of usbhs devices order USB1 > USB0 is good idea
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- usb0 pipe is same as default. own pipe config is not needed
- usb1 lost get_id function
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While SH7377 and others were updated to properly use SCIFA/B port types,
SH7367 was left behind. Fix it up accordingly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initialize ->irq_set_wake() in gic_arch_extn to unbreak wake
up from the KEYSC device on AG5EVM in case of Suspend-to-RAM.
Without this patch "echo mem > /sys/power/state" and a key
press results in the following message on resume:
WARNING: at kernel/irq/manage.c:507 irq_set_irq_wake+0x7c/0xd8()
Unbalanced IRQ 103 wake disable
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the board specific USB support
code for the sh7372 Mackerel board.
With this patch applied port CN22 is driven by the
recently added renesas_usbhs driver using the first
USB controller included in sh7372 aka USBHS0.
Hotplugging of USBHS0 unfortunately has to be
handled by software polling. The sh7372 SoC itself
obviously supports hotplug notification by IRQ but
on the Mackerel board this IRQ happens to be used
for the touch screen.
Also fix the pinmux configuration to avoid setting
up unused pins and fix minor spelling errors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a flag for SDHI1 to enable SDIO IRQ, and remove DMA Engine
slave id:s to disable DMA as a workaround.
Tested on sh73a0/AG5EVM with a BCM4318-based SDIO card.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On sh7372 the card-detection pin of SDHI0 can also produce interrupts,
when configured as GPIO. Use this feature to power down SDHI0, when no
card is plugged in.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
renesas_usbhs driver can use external interrupt mode
(which come from USB-PHY) or autonomy mode (it use own interrupt)
for detecting connection/disconnection when Function.
And it will be power OFF while it has been disconnecting
if external interrupt mode is selected.
mackerel board has 2 USB ports.
But we can not use external interrupt mode
on CN22 USB0 port which is only for USB Function.
IRQ7-PORT40 is already used by Touchscreen,
and USB-PHY needs IRQ7-PORT167.
It is impossible to use IRQ7 demux on mackerel.
We can use external interrupt mode USB-Function on "USB1".
USB1 can become Host by r8a66597, and become Function by renesas_usbhs.
But don't select both drivers in same time.
These 2 drivers are not supporting IRQ SHARD.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
renesas_usbhs is remake version of r8a66597
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Based on the patch by Takanari Hayama <taki@igel.co.jp>
Add the necessary platform data to add MERAM functionality to LCDC
Includes platform data for both the AP4EVB and mackerel
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes it possible to leave DMA slave IDs in the platform data
at default 0 value without hitting DMA channel allocation error paths.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes it possible to leave DMA slave IDs in the platform data
at default 0 value without hitting DMA channel allocation error paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SDHI0 and SDHI1 slave ids for RX and TX to enable
DMA Engine support for SDHI on the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Simply add MMCIF slave ids for RX and TX to enable
DMA Engine support for the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SY-DMAC support via shdma.c to the sh73a0 SoC
including slave ids, platform data and clock bindings.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch ties in the previously added sh7372 sleep
mode known as Core Standby together with the shared
SH-Mobile ARM CPUIdle implementation.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a shared SH-Mobile ARM specific CPUIdle
implementation supporting WFI only at this point. It
serves as a common point for late registration of the
arch-specific CPUIdle code, and supports adding extra
sleep modes using the callback shmobile_cpuidle_setup()
together with shmobile_cpuidle_modes[].
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7372 Core Standby sleep mode support and tie it
in with the shared SH-Mobile ARM suspend code.
The Core Standby mode is the lightest sh7372-specific
sleep mode, cutting power to the ARM core excluding the
L2 cache. Any interrupt source can be used for wakeups.
The low level portion of this code is based on the
TI OMAP sleep code in sleep34xx.S, thanks to them.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a simple Suspend-to-RAM implementation
for SH-Mobile ARM. The struct shmobile_suspend_ops are
kept global to allow cpu-specific code to override
the callbacks if needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use soc_camera_platform helper functions to dynamically manage the
camera device.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SDHI0 and SDHI1 support to the AG5EVM board
including platform data, pinmux configuration
and clock bindings.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reverts "ARM: mach-shmobile: sh7372 SDHI vector merge" and
supplies 3 IRQ resources for each SDHI block.
Some blocks have a 4th IRQ, but this is used for DRM feathres
that I do not have access tot he documentation for and are almost
certainly tainted by licensing issues. So the 4th IRQ is not
hooked-up even if it exists.
Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the struct resources for DSI0 to include the
hardware block name. Purely cosmetic, makes /proc/iomem
look slightly better.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the case of too late twd_base initialization for SMP
on sh73a0 which bas been broken because sh73a0 specific
smp_prepare_cpu() and percpu_timer_setup() changed order
in the commits:
05c74a6cbcc413521eb4
Without this fix the sh73a0 SMP kernel panics on boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Git commit f4117ac9e2
introduced PLAT_PHYS_OFFSET, but headsmp.S was left
unchanged which results in a compile error:
AS arch/arm/mach-shmobile/headsmp.o
arch/arm/mach-shmobile/headsmp.S: Assembler messages:
arch/arm/mach-shmobile/headsmp.S:27: Error: undefined symbol `secondary_startup' in operation
arch/arm/mach-shmobile/headsmp.S:27: Error: undefined symbol `PHYS_OFFSET' in operation
make[1]: *** [arch/arm/mach-shmobile/headsmp.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7372 clock code to set the RT side
set of MSTP bits to a fixed disabled state.
The sh7372 SoC contains two sets of MSTP bits,
one for the ARM (SYS) side, and one for the
SH4AL-DSP (RT) side. The actual clock associated
with the MSTP bit will only be stopped when both
sides have set the MSTP bit to disabled mode.
Some MSTP bits are enabled by default after
hardware reset, so this patch adjusts the code
to disable all MSTP bits associated with the RT
side to allow the SYS side to have full control.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The PLLC2 clock on AP4 systems does not need to run constantly to be
able to use HDMI. The HDMI hotplug interrupt works without the PLL
too, after which all the necessary clocks will be turned on by the
runtime PM.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add DMA mode support for the MMCIF controller on mackerel.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remember to also check for the CONFIG_MMC_SH_MMCIF_MODULE option
for the case of a modular MMCIF driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the following sh7377 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the following sh7372 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the following sh7367 multimedia hardware blocks
using UIO: VPU, VEU[0-3], VEU2H, JPU and SPU1
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7377 serial port types to make use of
PORT_SCIFA and PORT_SCIFB. This makes the software
match the sh7377 data sheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* Set receive enable and transmit enable bits of SCASCR0 (E6C400089).
Values previously written to this register was bogus.
Curiously earlyprintk works with the previous code.
* Remove duplicate initialisation of GPIO port 152, SCIFA0_TXD (0xE6053098).
This should have no effect other than to very slightly reduce the amount of
code.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many different platforms and subsystems may want to disable device
clocks during suspend and enable them during resume which is going to
be done in a very similar way in all those cases. For this reason,
provide generic routines for the manipulation of device clocks during
suspend and resume.
Convert the ARM shmobile platform to using the new routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some subsystems need to attach PM-related data to struct device and
they need to use devres for this purpose. For their convenience
and to make code more straightforward, add a new field called
subsys_data to struct dev_pm_info and let subsystems use it for
attaching PM-related information to devices.
Convert the ARM shmobile platform to using the new field.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
shmobile platforms replace the runtime PM callbacks of the platform
bus type with their own routines, but this means that the callbacks
are replaced system-wide. This may not be the right approach if the
platform devices on the system are not of the same type (e.g. some
of them belong to an SoC and the others are located in separate
chips), because in those cases they may require different handling.
Thus it is better to use power domains to override the platform bus
type's PM handling, as it generally is possible to use different
power domains for devices with different PM requirements.
Define a default power domain for shmobile in both the SH and ARM
falvors and use it to override the platform bus type's PM callbacks.
Since the suspend and hibernate callbacks of the new "default" power
domains need to be the same and the platform bus type's suspend and
hibernate callbacks for the time being, export those callbacks so
that can be used outside of the platform bus type code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
clock status check is not needed in recalc function.
clk->rate will be 0 in clk_set_rate without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If several boards are enabled in the kernel configuration,
fsi_init_pm_clock() functions from board-ap4evb.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If several boards are enabled in the kernel configuration,
hdmi_init_pm_clock() functions from board-ap4evb.c and board-mackerel.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I made a bit of a thinko when adding Mackerel to the boards
that support zboot using MMCIF.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
SDHI registers occupy only a 0x100 byte large window, not 0x200 byte.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>