Vladimir Oltean says:
====================
Unlock new potential in SJA1105 with PTP system timestamping
The SJA1105 being an automotive switch means it is designed to live in a
set-and-forget environment, far from the configure-at-runtime nature of
Linux. Frequently resetting the switch to change its static config means
it loses track of its PTP time, which is not good.
This patch series implements PTP system timestamping for this switch
(using the API introduced for SPI here:
https://www.mail-archive.com/netdev@vger.kernel.org/msg316725.html),
adding the following benefits to the driver:
- When under control of a user space PTP servo loop (ptp4l, phc2sys),
the loss of sync during a switch reset is much more manageable, and
the switch still remains in the s2 (locked servo) state.
- When synchronizing the switch using the software technique (based on
reading clock A and writing the value to clock B, as opposed to
relying on hardware timestamping), e.g. by using phc2sys, the sync
accuracy is vastly improved due to the fact that the actual switch PTP
time can now be more precisely correlated with something of better
precision (CLOCK_REALTIME). The issue is that SPI transfers are
inherently bad for measuring time with low jitter, but the newly
introduced API aims to alleviate that issue somewhat.
This series is also a requirement for a future patch set that adds full
time-aware scheduling offload support for the switch.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose here is to avoid ptp4l fail due to this condition:
timed out while polling for tx timestamp
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
port 1: send peer delay request failed
So either reset the switch before the management frame was sent, or
after it was timestamped as well, but not in the middle.
The condition may arise either due to a true timeout (i.e. because
re-uploading the static config takes time), or due to the TX timestamp
actually getting lost due to reset. For the former we can increase
tx_timestamp_timeout in userspace, for the latter we need this patch.
Locking all traffic during switch reset does not make sense at all,
though. Forcing all CPU-originated traffic to potentially block waiting
for a sleepable context to send > 800 bytes over SPI is not a good idea.
Flows that are autonomously forwarded by the switch will get dropped
anyway during switch reset no matter what. So just let all other
CPU-originated traffic be dropped as well.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP time of the switch is not preserved when uploading a new static
configuration. Work around this hardware oddity by reading its PTP time
before a static config upload, and restoring it afterwards.
Static config changes are expected to occur at runtime even in scenarios
directly related to PTP, i.e. the Time-Aware Scheduler of the switch is
programmed in this way.
Perhaps the larger implication of this patch is that the PTP .gettimex64
and .settime functions need to be exposed to sja1105_main.c, where the
PTP lock needs to be held during this entire process. So their core
implementation needs to move to some common functions which get exposed
in sja1105_ptp.h.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through the PTP_SYS_OFFSET_EXTENDED ioctl, it is possible for userspace
applications (i.e. phc2sys) to compensate for the delays incurred while
reading the PHC's time.
The task itself of taking the software timestamp is delegated to the SPI
subsystem, through the newly introduced API in struct spi_transfer. The
goal is to cross-timestamp I/O operations on the switch's PTP clock with
values in the local system clock (CLOCK_REALTIME). For that we need to
understand a bit of the hardware internals.
The 'read PTP time' message is a 12 byte structure, first 4 bytes of
which represent the SPI header, and the last 8 bytes represent the
64-bit PTP time. The switch itself starts processing the command
immediately after receiving the last bit of the address, i.e. at the
middle of byte 3 (last byte of header). The PTP time is shadowed to a
buffer register in the switch, and retrieved atomically during the
subsequent SPI frames.
A similar thing goes on for the 'write PTP time' message, although in
that case the switch waits until the 64-bit PTP time becomes fully
available before taking any action. So the byte that needs to be
software-timestamped is byte 11 (last) of the transfer.
The patch creates a common (and local) sja1105_xfer implementation for
the SPI I/O, and offers 3 front-ends:
- sja1105_xfer_u32 and sja1105_xfer_u64: these are capable of optionally
requesting a PTP timestamp
- sja1105_xfer_buf: this is for large transfers (e.g. the static config
buffer) and other misc data, and there is no point in giving
timestamping capabilities to this.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
r8169: improve PHY configuration
This series adds helpers to improve and simplify the PHY
configuration on various network chip versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8168c_4_hw_phy_config() duplicates rtl8168c_3_hw_phy_config(),
so we can remove the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain integrated PHY's from RTL8168d support extended pages. On page
0x0007 the number of the extended page is written to register 0x1e,
then the registers on the extended page can be accessed. Add a helper
for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phylib MDIO access functions in more places to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168d support an indirect access method for
PHY parameters. On page 0x0005 parameter number is written to register
0x05, then the parameter can be accessed via register 0x06.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168g support an indirect access method for
PHY parameters. On page 0x0a43 parameter number is written to register
0x13, then the parameter can be accessed via register 0x14.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current upstream interface is an all-or-nothing, which is
sub-optimal for future changes, as it doesn't allow the upstream driver
to prepare for the SFP module becoming available, as it is at boot.
Switch to a find-sfp-bus, add-upstream, del-upstream, put-sfp-bus
interface structure instead, which allows the upstream driver to
prepare for a module being available as soon as add-upstream is called.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAl3F+DIQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpkVmD/9FIa092Q6obga0RqA16GlbI85tgtNyRFZU
neIO/g9R3G/uBTGbiUeXHXHDz9CqUXIRYX7pmI2u0b07iGLRz8oUsOsgyVEfCMen
VitqwkJJAZ9j9OifyKpLYCZX9ulVDWX5hEz/vm2cNWDkjCbOpXvRuQmkXEzp7RNM
F7K25PpGLvJHfqC90q9FXXxNDlB2i1M/rh5I7eUqhb6rHmzfJGKCd+H80t+REoB1
iXAygPj86agQKLOUKZtJjXUjq9Ol/0FD+OKY+eP3EfVv/FJvIeWWYe78WplxJpRD
BYb9dhLMCSo619WVVy4hNYCPjSfPKVT2cO5QJmVRpgOI1urFuTNgNoIiw06AgvkZ
09vrlrJZ5A7eFEppuAFQC4WRYKWCQCQfq8wxt2iGUivXgHfskjJ7qJz1Mh5Nlxsr
JGm1hSVw9UCBzjqC75K2CR+vVt4T8ovEaizPFvzVj6lQ0lRTmSchisxbXzTdevOn
kFvBOntBdpeSq/CwZ0x5PDP4AbRsgH3ny47LCJoEpFZlxlOLuEB/dAx564dn6ZgZ
rRz6mKU7rlO7brrkW+DbRZ0XiOn5qzN6FrcSGX1DBzc4+hMus/5PPjv8Gk+Wo1PU
388mu6N6DObSjw1ij1AqkwyzudmbrziKM4isJY4I72I0YGSq9cuG5VXgM2GqbGlU
XXpzsu8pSw==
=8B/z
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Two NVMe device removal crash fixes, and a compat fixup for for an
ioctl that was introduced in this release (Anton, Charles, Max - via
Keith)
- Missing error path mutex unlock for drbd (Dan)
- cgroup writeback fixup on dead memcg (Tejun)
- blkcg online stats print fix (Tejun)
* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
block: drbd: remove a stray unlock in __drbd_send_protocol()
blkcg: make blkcg_print_stat() print stats only for online blkgs
nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
nvme-rdma: fix a segmentation fault during module unload
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c99 ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Xin Long says:
====================
sctp: update from rfc7829
SCTP-PF was implemented based on a Internet-Draft in 2012:
https://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
It's been updated quite a few by rfc7829 in 2016.
This patchset adds the following features:
1. add SCTP_ADDR_POTENTIALLY_FAILED notification
2. add pf_expose per netns/sock/asoc
3. add SCTP_EXPOSE_POTENTIALLY_FAILED_STATE sockopt
4. add ps_retrans per netns/sock/asoc/transport
(Primary Path Switchover)
5. add spt_pathcpthld for SCTP_PEER_ADDR_THLDS sockopt
v1->v2:
- See Patch 2/5 and Patch 5/5.
v2->v3:
- See Patch 1/5, 2/5 and 3/5.
v3->v4:
- See Patch 1/5, 2/5, 3/5 and 4/5.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 7.2 of rfc7829: "Peer Address Thresholds (SCTP_PEER_ADDR_THLDS)
Socket Option" extends 'struct sctp_paddrthlds' with 'spt_pathcpthld'
added to allow a user to change ps_retrans per sock/asoc/transport, as
other 2 paddrthlds: pf_retrans, pathmaxrxt.
Note: to not break the user's program, here to support pf_retrans dump
and setting by adding a new sockopt SCTP_PEER_ADDR_THLDS_V2, and a new
structure sctp_paddrthlds_v2 instead of extending sctp_paddrthlds.
Also, when setting ps_retrans, the value is not allowed to be greater
than pf_retrans.
v1->v2:
- use SCTP_PEER_ADDR_THLDS_V2 to set/get pf_retrans instead,
as Marcelo and David Laight suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new feature defined in section 5 of rfc7829: "Primary Path
Switchover". By introducing a new tunable parameter:
Primary.Switchover.Max.Retrans (PSMR)
The primary path will be changed to another active path when the path
error counter on the old primary path exceeds PSMR, so that "the SCTP
sender is allowed to continue data transmission on a new working path
even when the old primary destination address becomes active again".
This patch is to add this tunable parameter, 'ps_retrans' per netns,
sock, asoc and transport. It also allows a user to change ps_retrans
per netns by sysctl, and ps_retrans per sock/asoc/transport will be
initialized with it.
The check will be done in sctp_do_8_2_transport_strike() when this
feature is enabled.
Note this feature is disabled by initializing 'ps_retrans' per netns
as 0xffff by default, and its value can't be less than 'pf_retrans'
when changing by sysctl.
v3->v4:
- add define SCTP_PS_RETRANS_MAX 0xffff, and use it on extra2 of
sysctl 'ps_retrans'.
- add a new entry for ps_retrans on ip-sysctl.txt.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a sockopt defined in section 7.3 of rfc7829: "Exposing
the Potentially Failed Path State", by which users can change
pf_expose per sock and asoc.
The new sockopt SCTP_EXPOSE_POTENTIALLY_FAILED_STATE is also
known as SCTP_EXPOSE_PF_STATE for short.
v2->v3:
- return -EINVAL if params.assoc_value > SCTP_PF_EXPOSE_MAX.
- define SCTP_EXPOSE_PF_STATE SCTP_EXPOSE_POTENTIALLY_FAILED_STATE.
v3->v4:
- improve changelog.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP Quick failover draft section 5.1, point 5 has been removed
from rfc7829. Instead, "the sender SHOULD (i) notify the Upper
Layer Protocol (ULP) about this state transition", as said in
section 3.2, point 8.
So this patch is to add SCTP_ADDR_POTENTIALLY_FAILED, defined
in section 7.1, "which is reported if the affected address
becomes PF". Also remove transport cwnd's update when moving
from PF back to ACTIVE , which is no longer in rfc7829 either.
Note that ulp_notify will be set to false if asoc->expose is
not 'enabled', according to last patch.
v2->v3:
- define SCTP_ADDR_PF SCTP_ADDR_POTENTIALLY_FAILED.
v3->v4:
- initialize spc_state with SCTP_ADDR_AVAILABLE, as Marcelo suggested.
- check asoc->pf_expose in sctp_assoc_control_transport(), as Marcelo
suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said in rfc7829, section 3, point 12:
The SCTP stack SHOULD expose the PF state of its destination
addresses to the ULP as well as provide the means to notify the
ULP of state transitions of its destination addresses from
active to PF, and vice versa. However, it is recommended that
an SCTP stack implementing SCTP-PF also allows for the ULP to be
kept ignorant of the PF state of its destinations and the
associated state transitions, thus allowing for retention of the
simpler state transition model of [RFC4960] in the ULP.
Not only does it allow to expose the PF state to ULP, but also
allow to ignore sctp-pf to ULP.
So this patch is to add pf_expose per netns, sock and asoc. And in
sctp_assoc_control_transport(), ulp_notify will be set to false if
asoc->expose is not 'enabled' in next patch.
It also allows a user to change pf_expose per netns by sysctl, and
pf_expose per sock and asoc will be initialized with it.
Note that pf_expose also works for SCTP_GET_PEER_ADDR_INFO sockopt,
to not allow a user to query the state of a sctp-pf peer address
when pf_expose is 'disabled', as said in section 7.3.
v1->v2:
- Fix a build warning noticed by Nathan Chancellor.
v2->v3:
- set pf_expose to UNUSED by default to keep compatible with old
applications.
v3->v4:
- add a new entry for pf_expose on ip-sysctl.txt, as Marcelo suggested.
- change this patch to 1/5, and move sctp_assoc_control_transport
change into 2/5, as Marcelo suggested.
- use SCTP_PF_EXPOSE_UNSET instead of SCTP_PF_EXPOSE_UNUSED, and
set SCTP_PF_EXPOSE_UNSET to 0 in enum, as Marcelo suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a simple test for recently added netdevice alternative names.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuong Lien says:
====================
TIPC Encryption
This series provides TIPC encryption feature, kernel part. There will be
another one in the 'iproute2/tipc' for user space to set key.
v2: add select crypto 'aes(gcm)' for TIPC_CRYPTO in Kconfig
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds two netlink commands to TIPC in order for user to be
able to set or remove AEAD keys:
- TIPC_NL_KEY_SET
- TIPC_NL_KEY_FLUSH
When the 'KEY_SET' is given along with the key data, the key will be
initiated and attached to TIPC crypto. On the other hand, the
'KEY_FLUSH' command will remove all existing keys if any.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit offers an option to encrypt and authenticate all messaging,
including the neighbor discovery messages. The currently most advanced
algorithm supported is the AEAD AES-GCM (like IPSec or TLS). All
encryption/decryption is done at the bearer layer, just before leaving
or after entering TIPC.
Supported features:
- Encryption & authentication of all TIPC messages (header + data);
- Two symmetric-key modes: Cluster and Per-node;
- Automatic key switching;
- Key-expired revoking (sequence number wrapped);
- Lock-free encryption/decryption (RCU);
- Asynchronous crypto, Intel AES-NI supported;
- Multiple cipher transforms;
- Logs & statistics;
Two key modes:
- Cluster key mode: One single key is used for both TX & RX in all
nodes in the cluster.
- Per-node key mode: Each nodes in the cluster has one specific TX key.
For RX, a node requires its peers' TX key to be able to decrypt the
messages from those peers.
Key setting from user-space is performed via netlink by a user program
(e.g. the iproute2 'tipc' tool).
Internal key state machine:
Attach Align(RX)
+-+ +-+
| V | V
+---------+ Attach +---------+
| IDLE |---------------->| PENDING |(user = 0)
+---------+ +---------+
A A Switch| A
| | | |
| | Free(switch/revoked) | |
(Free)| +----------------------+ | |Timeout
| (TX) | | |(RX)
| | | |
| | v |
+---------+ Switch +---------+
| PASSIVE |<----------------| ACTIVE |
+---------+ (RX) +---------+
(user = 1) (user >= 1)
The number of TFMs is 10 by default and can be changed via the procfs
'net/tipc/max_tfms'. At this moment, as for simplicity, this file is
also used to print the crypto statistics at runtime:
echo 0xfff1 > /proc/sys/net/tipc/max_tfms
The patch defines a new TIPC version (v7) for the encryption message (-
backward compatibility as well). The message is basically encapsulated
as follows:
+----------------------------------------------------------+
| TIPCv7 encryption | Original TIPCv2 | Authentication |
| header | packet (encrypted) | Tag |
+----------------------------------------------------------+
The throughput is about ~40% for small messages (compared with non-
encryption) and ~9% for large messages. With the support from hardware
crypto i.e. the Intel AES-NI CPU instructions, the throughput increases
upto ~85% for small messages and ~55% for large messages.
By default, the new feature is inactive (i.e. no encryption) until user
sets a key for TIPC. There is however also a new option - "TIPC_CRYPTO"
in the kernel configuration to enable/disable the new code when needed.
MAINTAINERS | add two new files 'crypto.h' & 'crypto.c' in tipc
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new structure 'tipc_aead_key' is added to the 'tipc.h' for user to
be able to transfer a key to TIPC in kernel. Netlink will be used for
this purpose in the later commits.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user sets RX key for a peer not existing on the own node, a new
node entry is needed to which the RX key will be attached. However,
since the peer node address (& capabilities) is unknown at that moment,
only the node-ID is provided, this commit allows the creation of a node
with only the data that we call as “preliminary”.
A preliminary node is not the object of the “tipc_node_find()” but the
“tipc_node_find_by_id()”. Once the first message i.e. LINK_CONFIG comes
from that peer, and is successfully decrypted by the own node, the
actual peer node data will be properly updated and the node will
function as usual.
In addition, the node timer always starts when a node object is created
so if a preliminary node is not used, it will be cleaned up.
The later encryption functions will also use the node timer and be able
to create a preliminary node automatically when needed.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a need to support the crypto asynchronous operations in the later
commits, apart from the current RCU mechanism for bearer pointer, we
add a 'refcnt' to the bearer object as well.
So, a bearer can be hold via 'tipc_bearer_hold()' without being freed
even though the bearer or interface can be disabled in the meanwhile.
If that happens, the bearer will be released then when the crypto
operation is completed and 'tipc_bearer_put()' is called.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-08
Another series that contains updates to the ice driver only.
Anirudh cleans up the code of kernel config of ifdef wrappers by moving
code that is needed by DCB to disable and enable the PF VSI for
configuration. Implements ice_vsi_type_str() to convert an VSI type
enum value to its string equivalent to help identify VSI types from
module print statements.
Usha and Tarun add support for setting the maximum per-queue bit rate
for transmit queues.
Dave implements dcb_nl set functions and supporting software DCB
functions to support the callbacks defined in the dcbnl_rtnl_ops
structure.
Henry adds a check to ensure we are not resetting the device when trying
to configure it, and to return -EBUSY during a reset.
Usha fixes a call trace caused by the receive/transmit descriptor size
change request via ethtool when DCB is configured by using the number of
enabled queues and not the total number of allocated queues.
Paul cleans up and refactors the software LLDP configuration to handle
when firmware DCBX is disabled.
Akeem adds checks to ensure the VF or PF is not disabled before honoring
mailbox messages to configure the VF.
Brett corrects the check to make sure the vector_id passed down from
iavf is less than the max allowed interrupts per VF. Updates a flag bit
to align with the current specification.
Bruce updates a switch statement to use the correct status of the
Download Package AQ command. Does some housekeeping by cleaning up a
conditional check that is not needed.
Mitch shortens up the delay for SQ responses to resolve issues with VF
resets failing.
Jake cleans up the code reducing namespace pollution and to simplify
ice_debug_cq() since it always uses the same mask, not need to pass it
in. Improve debugging by adding the command opcode in the debug
messages that print an error code.
v2: fixed reverse christmas tree issue in patch 3 of the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's one more fix to keep a reference to the driver's module as long
as there are users of the PWM exposed by the driver.
-----BEGIN PGP SIGNATURE-----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=WelB
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fix from Thierry Reding:
"One more fix to keep a reference to the driver's module as long as
there are users of the PWM exposed by the driver"
* tag 'pwm/for-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: Prevent unloading the driver module while in use
cgroup writeback tries to refresh the associated wb immediately if the
current wb is dead. This is to avoid keeping issuing IOs on the stale
wb after memcg - blkcg association has changed (ie. when blkcg got
disabled / enabled higher up in the hierarchy).
Unfortunately, the logic gets triggered spuriously on inodes which are
associated with dead cgroups. When the logic is triggered on dead
cgroups, the attempt fails only after doing quite a bit of work
allocating and initializing a new wb.
While c3aab9a0bd ("mm/filemap.c: don't initiate writeback if mapping
has no dirty pages") alleviated the issue significantly as it now only
triggers when the inode has dirty pages. However, the condition can
still be triggered before the inode is switched to a different cgroup
and the logic simply doesn't make sense.
Skip the immediate switching if the associated memcg is dying.
This is a simplified version of the following two patches:
* https://lore.kernel.org/linux-mm/20190513183053.GA73423@dennisz-mbp/
* http://lkml.kernel.org/r/156355839560.2063.5265687291430814589.stgit@buzz
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: e8a7abf5a5 ("writeback: disassociate inodes from dying bdi_writebacks")
Acked-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
further restrict copy_file_range() to avoid potential data corruption
from Luis and a fix for !CONFIG_CEPH_FSCACHE kernels. Everything but
the fscache fix is marked for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl3FjtQTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHziyjfCACbNiRHpTWfuZ1iHXXCpo0tAixOT6i0
9ZlE8yiF6U6iH7uv/MuIeJ+Qeep9+6wwgJYEJKcF0e+Raiob7womDO+yeDx6RYrC
bqq6OLjJl8VbfeQWvJTmisGTPpvOsOKxxXIKG6vx1zJaJ69yENilFZ0biis14iTu
RRDvtSntc96OhZ3n8IXie2+f9purYeIKhiCZqx9WzYZOk5sb3zGyhqD+Wh5kxkEh
QzwwZ/G5RYvMMhL0o13uMZrjqozGTI9Qm09u7+EikIXFFtt+szEdgFd4pQPhsC1D
VmpdrvV4ml8JnbkENiZ7tlHCcICQJfgMWNcLVgHvD6808CJ0UP5Cq/jP
=34Iz
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Some late-breaking dentry handling fixes from Al and Jeff, a patch to
further restrict copy_file_range() to avoid potential data corruption
from Luis and a fix for !CONFIG_CEPH_FSCACHE kernels.
Everything but the fscache fix is marked for stable"
* tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client:
ceph: return -EINVAL if given fsc mount option on kernel w/o support
ceph: don't allow copy_file_range when stripe_count != 1
ceph: don't try to handle hashed dentries in non-O_CREAT atomic_open
ceph: add missing check in d_revalidate snapdir handling
ceph: fix RCU case handling in ceph_d_revalidate()
ceph: fix use-after-free in __ceph_remove_cap()
The "42f5cda5eaf4" commit rightly set SOCK_DONE on peer shutdown,
but there is an issue if we receive the SHUTDOWN(RDWR) while the
virtio_transport_close_timeout() is scheduled.
In this case, when the timeout fires, the SOCK_DONE is already
set and the virtio_transport_close_timeout() will not call
virtio_transport_reset() and virtio_transport_do_close().
This causes that both sockets remain open and will never be released,
preventing the unloading of [virtio|vhost]_transport modules.
This patch fixes this issue, calling virtio_transport_reset() and
virtio_transport_do_close() when we receive the SHUTDOWN(RDWR)
and there is nothing left to read.
Fixes: 42f5cda5ea ("vsock/virtio: set SOCK_DONE on peer shutdown")
Cc: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to do this conditional check before the assignment so
simply remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller