The code for "powersurge" SMP would kick in and cause a crash
at boot due to the lack of a NULL test.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the old days, we treated all interrupts from the legacy Apple home made
interrupt controllers as level, with a trick reading the "level" register
along with the "event" register to work arounds bugs where it would
occasionally fail to latch some events.
Doing so appeared to work fine for both level and edge interrupts.
Later on, we discovered in Darwin source the magic masks that define which
interrupts are actually level and which are edge, and implemented a
different algorithm, more similar to what Apple does, that treats those
differently.
I recently discovered however that this caused problems (including loss
of interrupts) with an old Wallstreet PowerBook when trying to use the
internal modem (connected to a cascaded controller).
It looks like some interrupts are treated as edge while they are really
level and I'm starting to seriously doubt the correctness of the Darwin
code (which has other obvious bugs when you read it, so ...)
This patch reverts to our original behaviour of treating everything as
a level interrupt. It appears to solve the problems with the modem on
the Wallstreet and everything else seems to be working properly as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make cputime_t and cputime64_t nocast to enable sparse checking to
detect incorrect use of cputime. Drop the cputime macros for simple
scalar operations. The conversion macros are still needed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A large chunk of qe_pin_request() is unnecessarily cut-and-paste
directly from of_get_named_gpio_flags(). This patch cuts out the
duplicate code and replaces it with a call to of_get_gpio().
v2: fixed compile error due to missing gpio_to_chip()
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The PowerPC pSeries platform (CONFIG_PPC_PSERIES=y) enables
hypervisor-call tracing for CONFIG_TRACEPOINTS=y kernels. One of the
hypervisor calls that is traced is the H_CEDE call in the idle loop
that tells the hypervisor that this OS instance no longer needs the
current CPU. However, tracing uses RCU, so this combination of kernel
configuration variables needs to avoid telling RCU about the current CPU's
idleness until after the H_CEDE-entry tracing completes on the one hand,
and must tell RCU that the the current CPU is no longer idle before the
H_CEDE-exit tracing starts.
In all other cases, it suffices to inform RCU of CPU idleness upon
idle-loop entry and exit.
This commit makes the required adjustments.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Sending a break on the SOC UARTs found in some MPC83xx/85xx/86xx
chips seems to cause a short lived IRQ storm (/proc/interrupts
typically shows somewhere between 300 and 1500 events). Unfortunately
this renders SysRQ over the serial console completely inoperable.
The suggested workaround in the errata is to read the Rx register,
wait one character period, and then read the Rx register again.
We achieve this by tracking the old LSR value, and on the subsequent
interrupt event after a break, we don't read LSR, instead we just
read the RBR again and return immediately.
The "fsl,ns16550" is used in the compatible field of the serial
device to mark UARTs known to have this issue.
Thanks to Scott Wood for providing the errata data which led to
a much cleaner fix.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
CONFIG_PPC47x doesn't exist in Kconfig and no 476 processor calls this
function ppc44x_pin_tlb() as it has it's own ppc47x_pin_tlb().
This code is probably an artifact of the original 476 code that
shouldn't have made it upstream.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Needed if you want to use swiotlb, harmless otherwise.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.
Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Now all ARCH_POPULATES_NODE_MAP archs select HAVE_MEBLOCK_NODE_MAP -
there's no user of early_node_map[] left. Kill early_node_map[] and
replace ARCH_POPULATES_NODE_MAP with HAVE_MEMBLOCK_NODE_MAP. Also,
relocate for_each_mem_pfn_range() and helper from mm.h to memblock.h
as page_alloc.c would no longer host an alternative implementation.
This change is ultimately one to one mapping and shouldn't cause any
observable difference; however, after the recent changes, there are
some functions which now would fit memblock.c better than page_alloc.c
and dependency on HAVE_MEMBLOCK_NODE_MAP instead of HAVE_MEMBLOCK
doesn't make much sense on some of them. Further cleanups for
functions inside HAVE_MEMBLOCK_NODE_MAP in mm.h would be nice.
-v2: Fix compile bug introduced by mis-spelling
CONFIG_HAVE_MEMBLOCK_NODE_MAP to CONFIG_MEMBLOCK_HAVE_NODE_MAP in
mmzone.h. Reported by Stephen Rothwell.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
powerpc doesn't access early_node_map[] directly and enabling
HAVE_MEMBLOCK_NODE_MAP is trivial - replacing add_active_range() calls
with memblock_set_node() and selecting HAVE_MEMBLOCK_NODE_MAP is
enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
The only function of memblock_analyze() is now allowing resize of
memblock region arrays. Rename it to memblock_allow_resize() and
update its users.
* The following users remain the same other than renaming.
arm/mm/init.c::arm_memblock_init()
microblaze/kernel/prom.c::early_init_devtree()
powerpc/kernel/prom.c::early_init_devtree()
openrisc/kernel/prom.c::early_init_devtree()
sh/mm/init.c::paging_init()
sparc/mm/init_64.c::paging_init()
unicore32/mm/init.c::uc32_memblock_init()
* In the following users, analyze was used to update total size which
is no longer necessary.
powerpc/kernel/machine_kexec.c::reserve_crashkernel()
powerpc/kernel/prom.c::early_init_devtree()
powerpc/mm/init_32.c::MMU_init()
powerpc/mm/tlb_nohash.c::__early_init_mmu()
powerpc/platforms/ps3/mm.c::ps3_mm_add_memory()
powerpc/platforms/embedded6xx/wii.c::wii_memory_fixups()
sh/kernel/machine_kexec.c::reserve_crashkernel()
* x86/kernel/e820.c::memblock_x86_fill() was directly setting
memblock_can_resize before populating memblock and calling analyze
afterwards. Call memblock_allow_resize() before start populating.
memblock_can_resize is now static inside memblock.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
* early_init_devtree(): Total memory size is aligned to PAGE_SIZE;
however, alignment isn't enforced if memory_limit is explicitly
specified. Simplify the logic and always apply PAGE_SIZE alignment.
* MMU_init(): memblock regions is truncated by directly modifying
memblock.memory.cnt. This is incomplete (reserved array is not
truncated) and unnecessarily low level hindering further memblock
improvments. Use memblock_enforce_memory_limit() instead.
* wii_memory_fixups(): Unnecessarily low level direct manipulation of
memblock regions. The same result can be achieved using properly
abstracted operations. Reimplement using memblock API.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
memblock_init() initializes arrays for regions and memblock itself;
however, all these can be done with struct initializers and
memblock_init() can be removed. This patch kills memblock_init() and
initializes memblock with struct initializer.
The only difference is that the first dummy entries don't have .nid
set to MAX_NUMNODES initially. This doesn't cause any behavior
difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
24aa07882b (memblock, x86: Replace memblock_x86_reserve/free_range()
with generic ones) removed arch/x86/include/asm/memblock.h and dropped
its inclusion from include/linux/memblock.h which breaks other
architectures which depended on the generic memblock.h pulling in the
arch specific one.
However, the proper fix isn't adding back the asm inclusion. memblock
doesn't have any arch dependent part and doesn't need arch specific
header file and asm/memblock.h files are either practically empty or
contain mostly unrelated arch specific stuff.
* In microblaze, sh, powerpc, sparc and openrisc, asm/memblock.h is
either empty or just contains unused MEMBLOCK_DBG() macro. Remove
them.
* In arm and unicore32, asm/memblock.h contains arch specific stuff.
Include it directly from its users. It might be a good idea to
rename the header file to avoid confusion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Most distros use it so we may as well enable it and get regular compile
testing.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When issuing a system reset we almost always oops in the oops_to_nvram
code because multiple CPUs are using the deflate work area. Add a
spinlock to protect it.
To play it safe I'm using trylock to avoid locking up if the NVRAM
code oopses. This means we might miss multiple CPUs oopsing at exactly
the same time but I think it's best to play it safe for now. Once we
are happy with the reliability we can change it to a full spinlock.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time. The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.
The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle. So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state. We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n". Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.
The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero. The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The minimum RMO size field in ibm,client-architecture is currently
ignored, but a future firmware version will rectify that. Since we
always get at least 128MB of RMO right now, asking for 64MB is
likely to result in boot failures.
We should bump it to at least 128MB, but considering all the boot
issues we have on 128MB RMO boxes and all new machines have virtual
RMO, we may as well set our minimum to 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With CONFIG_STRICT_DEVMEM=y, user space cannot read any part of /dev/mem.
Since this breaks librtas, punch a hole in /dev/mem to allow access to the
rmo_buffer that librtas needs.
Anton Blanchard reported the problem and helped with the fix.
A quick test for this patch:
# cat /proc/rtas/rmo_buffer
000000000f190000 10000
# python -c "print 0x000000000f190000 / 0x10000"
3865
# dd if=/dev/mem of=/tmp/foo count=1 bs=64k skip=3865
1+0 records in
1+0 records out
65536 bytes (66 kB) copied, 0.000205235 s, 319 MB/s
# dd if=/dev/mem of=/tmp/foo
dd: reading `/dev/mem': Operation not permitted
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.00022519 s, 0.0 kB/s
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.
This adds it using ppc40x_simple and provides a device-tree.
There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.
The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refresh ps3_defconfig to latest kernel sources and
change the options:
CONFIG_PPP=m to CONFIG_PPP=n.
CONFIG_NAMESPACES=y to CONFIG_NAMESPACES=n
CONFIG_NUMA=y to CONFIG_NUMA=n
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add an __init annotation to the ps3_smp_probe() routine.
Fixes build warnings like these when
CONFIG_DEBUG_SECTION_MISMATCH=y:
WARNING: Section mismatch in reference from the function .ps3_smp_probe()
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some PS3 repository.c build warnings when DEBUG is
defined. Also change most pr_debug calls to pr_devel calls.
Fixes warnings like these:
format '%lx' expects type 'long unsigned int', but argument 7 has type 'u64'
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1 hcall #91 should be named lv1_read_repository_node, and
not lv1_get_repository_node_value. Adjust the lv1 hcall table
and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1_get_version_info hcall takes 2, not 1 output
arguments. Adjust the lv1 hcall table and all calls.
Usage:
int lv1_get_version_info(u64 *version_number, u64 *vendor_id)
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1_get_virtual_address_space_id_of_ppe hcall takes 0, not 1 input
arguments. Adjust the lv1 hcall table and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1_net_stop_tx_dma and net_stop_rx_dma hcalls take 2, not 3 input
arguments. Adjust the lv1 hcall table and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
General code cleanup for PS3 interrupt.c:
o Fill out comments for structure members.
o Move variables ipi_debug_brk_mask and lock from struct ps3_bmp to
struct ps3_private.
o Fix pr_debug build errors when DEBUG is defined.
o Convert bit operation to set_bit().
o Convert DBG macro from pr_debug to pr_devel
o Add new macro FAIL to replace pr_debug calls
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We might enter the secondary CPU capture code twice, eg if we have to
unstick some CPUs with a system reset. In this case we don't want to
overwrite the state on CPUs that had made it into the capture code OK,
so use the cpus_state_saved cpumask for that and make it local to
crash_ipi_callback.
For controlling progress now use atomic_t cpus_in_crash to count how
many CPUs have made it into the kdump code, and time_to_dump to tell
everyone it's time to dump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we enter the kdump code via system reset, wait a bit before
sending the IPI to capture all secondary CPUs. Without it we race
with the hypervisor that is issuing the system reset to each CPU.
If the IPI gets there first the system reset oops output then shows
the register state of the IPI handler which is not what we want.
I took the opportunity to add defines for all the various delays
we have. There's no need for cpu_relax when we are doing an mdelay,
so remove them too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have an intermittent kdump fail where the hypervisor fails an H_EOI.
As a result our CPPR is never reset to 0xff and we no longer accept
interrupts.
This patch calls icp_hv_set_cppr to reset the CPPR if H_EOI fails,
fixing the kdump fail.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've had a 180 second panic timeout on ppc64 for as long as I
can remember. This patch reduces it to 10 seconds on pseries for a few
reasons:
- Almost all pseries machines have a hypervisor console so panic
output will be available in a scrollback buffer.
- The 180 seconds impacts our availability, users (other than
kernel hackers) just want the box to come back around so it
can continue its work.
- I spend a lot of my life staring at the 180 second panic timeout.
Many pseries machines take minutes to power cycle, so it's quicker
to sit through the 180 seconds than it is to power cycle.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our die() code was based off a very old x86 version. Update it to
mirror the current x86 code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove some unnecessary defines and fix some spelling mistakes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can handle recursion caused by system reset by reusing the crash
shutdown fault handler.
Since we don't have an OS triggerable NMI, if all CPUs don't make it
into kdump then we tell the user to issue a system reset. However if
we have a panic timeout set we cannot wait forever and must continue
the kdump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a lot of complicated logic that handles possible recursion between
kdump and a system reset exception. We can solve this in a much simpler
way using the same setjmp/longjmp tricks xmon does.
As a first step, this patch removes the old system reset code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I've been seeing truncated output when people send system reset info
to me. We should see a backtrace for every CPU, but the panic() code
takes the box down before they all make it out to the console. The
panic code runs unlocked so we also see corrupted console output.
If we are going to panic, then delay 1 second before calling into the
panic code. Move oops_exit inside the die lock and put a newline
between oopses for clarity.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch makes pseries_idle_driver not to be registered when
power_save=off kernel boot option is specified. The
cpuidle_disable variable used here is similar to
its usage on x86. If cpuidle_disable is set then
sysfs entries for cpuidle framework are not created
and the required drivers are not loaded.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables cpuidle for pSeries and pSeries_idle is
directly called from the idle loop. As a result of pSeries_idle, cpuidle
driver registered with cpuidle subsystem comes into action. On
failure of loading of the driver or cpuidle framework default idle
is executed as part of the function. This patch
also removes the routines pseries_shared_idle_sleep and
pseries_dedicated_idle_sleep as they are now implemented as part of
pseries_idle cpuidle driver.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch implements a back-end cpuidle driver for pSeries
based on pseries_dedicated_idle_loop and pseries_shared_idle_loop
routines. The driver is built only if CONFIG_CPU_IDLE is set. This
cpuidle driver uses global registration of idle states and
not per-cpu.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch provides cpu_idle_wait() routine for the powerpc
platform which is required by the cpuidle subsystem. This
routine is required to change the idle handler on SMP systems.
The equivalent routine for x86 is in arch/x86/kernel/process.c
but the powerpc implementation is different.
cpuidle_disable variable is to enable/disable cpuidle
framework if power_save option is set during the boot
time.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's only used inside the same file where it's defined. There's
also no point exporting it anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Open Firmware on OPAL machines seems to have issues if we close
stdin and/or we try to print things after calling "quiesce" so
we avoid doing both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Define HUGETLB_NEED_PRELOAD in mmu-book3e.h for CONFIG_PPC64 instead
of having a much more complicated #if block. This is easier to read
and maintain.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This avoids an extra find_vma() and is less error-prone.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Allow hugetlb to be enabled on 64b FSL_BOOK3E. No platforms enable
it by default yet.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For 64-bit FSL_BOOKE implementations, gigantic pages need to be
reserved at boot time by the memblock code based on the command line.
This adds the call that handles the reservation, and fixes some code
comments.
It also removes the previous pr_err when reserve_hugetlb_gpages
is called on a system without hugetlb enabled - the way the code is
structured, the call is unconditional and the resulting error message
spurious and confusing.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Before hugetlb, at each level of the table, we test for
!0 to determine if we have a valid table entry. With hugetlb, this
compare becomes:
< 0 is a normal entry
0 is an invalid entry
> 0 is huge
This works because the hugepage code pulls the top bit off the entry
(which for non-huge entries always has the top bit set) as an
indicator that we have a hugepage.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I happened to comment this code while I was digging through it;
we might as well commit that. I also made some whitespace
changes - the existing code had a lot of unnecessary newlines
that I found annoying when I was working on my tiny laptop.
No functional changes.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The original 32-bit hugetlb implementation used PPC64 vs PPC32 to
determine which code path to take. However, the final hugetlb
implementation for 64-bit FSL ended up shared with the FSL
32-bit code so the actual check needs to be FSL_BOOK3E vs
everything else. This patch changes the include protections to
reflect this.
There are also a couple of related comment fixes.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This updates the hugetlb page table code to handle 64-bit FSL_BOOKE.
The previous 32-bit work counted on the inner levels of the page table
collapsing.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch does 2 things: It corrects the code that determines the
size to write into MAS1 for the PPC_MM_SLICES case (this originally
came from David Gibson and I had incorrectly altered it), and it
changes the methodolody used to calculate the size for !PPC_MM_SLICES
to work for 64-bit as well as 32-bit.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There was an unconditional return of "1" in the original code
from David Gibson, and I dropped it because it wasn't needed
for FSL BOOKE 32-bit. However, not all systems (including 64-bit
FSL BOOKE) do loading of the hpte from the fault handler asm
and depend on this function returning 1, which causes a call
to update_mmu_cache() that writes an entry into the tlb.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we don't have slices, we should be able to use the generic
hugetlb_get_unmapped_area() code
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Cell and PowerMac platforms use virtually identical cascaded-IRQ
setup code, so just merge it into the core. Ideally this code would
trigger automatically when an MPIC device-node specifies an "interrupts"
property, perhaps even enabling MPIC_SECONDARY along the way.
Unfortunately, Benjamin Herrenschmidt has had bad experiences in the
past with the quality of Apple PowerMac device-trees, so to be safe we
will only try to parse out an IRQ if the MPIC_SECONDARY flag is set by
the caller.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Store the node pointer in the MPIC during initialization so that all of
the later operational code can just reuse the cached pointer.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's not really any reason to have this one-liner in a separate
static inline function, given that all the other similar tests are
already in the alloc_mpic() code.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't open-code the OpenFirmware "dcr-reg" property lookup trying to map
DCR resources. This makes the code a bit easier to read.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It turns out that there are only 2 in-tree platforms which use MPICs
which are not "primary": IBM Cell and PowerMac. To reduce the
complexity of the typical board setup code, invert the MPIC_PRIMARY bit
into MPIC_SECONDARY.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Almost all PowerPC platforms use a standard "open-pic" device node so
the mpic_alloc() function now accepts NULL for the device-node. This
will cause it to perform a default search with of_find_matching_node().
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MPIC code can already perform an automatic OF address translation
step as part of mpic_alloc(), but several boards need to use that base
address when they perform mpic_assign_isu().
The easiest solution is to save the computed physical address into the
"struct mpic" for later use by the board code.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All of the existing callers of mpic_alloc() pass in a non-NULL
device-node pointer, so the checks for a NULL device-node may be
removed.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of using the open-coded "reg" property lookup and address
translation in mpic_alloc(), directly call of_address_to_resource().
This includes various workarounds for special cases which the naive
of_address_translate() does not.
Afterwards it is possible to remove the copiously copy-pasted calls to
of_address_translate() from the 85xx/86xx/powermac platforms.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes a bunch of "extern" declarations and CONFIG_SMP ifdefs.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.
CC: devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
powerpc copied pci_iomap from generic code, probably to avoid
pulling the rest of iomap.c in. Since that's in
a separate file now, we can reuse the common implementation.
The only difference is handling of nocache flag,
that turns out to be done correctly by the
generic code since arch/powerpc/include/asm/io.h
defines ioremap_nocache same as ioremap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Conflicts & resolutions:
* arch/x86/xen/setup.c
dc91c728fd "xen: allow extra memory to be in multiple regions"
24aa07882b "memblock, x86: Replace memblock_x86_reserve/free..."
conflicted on xen_add_extra_mem() updates. The resolution is
trivial as the latter just want to replace
memblock_x86_reserve_range() with memblock_reserve().
* drivers/pci/intel-iommu.c
166e9278a3 "x86/ia64: intel-iommu: move to drivers/iommu/"
5dfe8660a3 "bootmem: Replace work_with_active_regions() with..."
conflicted as the former moved the file under drivers/iommu/.
Resolved by applying the chnages from the latter on the moved
file.
* mm/Kconfig
6661672053 "memblock: add NO_BOOTMEM config symbol"
c378ddd53f "memblock, x86: Make ARCH_DISCARD_MEMBLOCK a config option"
conflicted trivially. Both added config options. Just
letting both add their own options resolves the conflict.
* mm/memblock.c
d1f0ece6cd "mm/memblock.c: small function definition fixes"
ed7b56a799 "memblock: Remove memblock_memory_can_coalesce()"
confliected. The former updates function removed by the
latter. Resolution is trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Since commit 8a0a9bd4db, this comment in mmap_rnd() does not
hold true as the value returned by get_random_int() will in fact be
different every single call. Remove the comment and simplify the code
back to its original desired form.
This reverts commit a5adc91a4b which is no longer necessary and
also fixes the sparc code that copied this same adjustment.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During kdump stress testing I sometimes see the kdump kernel panic
with:
Interrupt 0x306 (real) is invalid, disabling it.
Kernel panic - not syncing: bad return code EOI - rc = -4, value=ff000306
Instead of panicing print the error message, dump the stack the first
time it happens and continue on. Add some more information to the
debug messages as well.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a 64bit book3s machine I have an oops from a system reset that
claims the book3e CE bit was set:
MSR: 8000000000021032 <ME,CE,IR,DR> CR: 24004082 XER: 00000010
On a book3s machine system reset sets IBM bit 46 and 47 depending on
the power saving mode. Separate the definitions by type and for
completeness add the rest of the bits in.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In lieu of having multiple similiar lines, we can just have one
generic cpu-as line for CONFIG_ALTIVEC
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CPC925/CPC945 use special window to access host bridge functionality of
u3-ht. Provide a way to access this device.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As described in the help text in the patch, this token restricts general
access to /dev/mem as a way of increasing the security. Specifically, access
to exclusive IOMEM and kernel RAM is denied unless CONFIG_STRICT_DEVMEM is
set to 'n'.
Implement the 'devmem_is_allowed()' interface for Powerpc. It will be
called from range_is_allowed() when userpsace attempts to access /dev/mem.
This patch is based on an earlier patch from Steve Best and with input from
Paul Mackerras and Scott Wood.
[BenH] Fixed a typo or two and removed the generic change which should
be submitted as a separate patch
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch below removes an extra semicolon.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: linuxppc-dev@lists.ozlabs.org
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On Fri, Nov 11, 2011 at 10:17:55AM +0530, Ananth N Mavinakayanahalli wrote:
> >
> > At this rate we're going to end up with no bits left for CPU features
> > way too quickly... Especially for something we only care about once at
> > boot time.
> >
> > Wouldn't CPU_FTR_PPCAS_ARCH_V2 be a good enough test ?
>
> /me checks Cell manuals... yes, that test would be good enough. I will
> cook up a patch to use this.
Here it is...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for p7IOC (and possibly other IODA v1 IO Hubs)
using OPAL v2 interfaces.
We completely take over resource assignment and assign them using an
algorithm that hands out device BARs in a way that makes them fit in
individual segments of the M32 window of the bridge, which enables us
to assign individual PEs to devices and functions.
The current implementation gives out a PE per functions on PCIe, and a
PE for the entire bridge for PCIe to PCI-X bridges.
This can be adjusted / fine tuned later.
We also setup DMA resources (32-bit only for now) and MSIs (both 32-bit
and 64-bit MSI are supported).
The DMA allocation tries to divide the available 256M segments of the
32-bit DMA address space "fairly" among PEs. This is done using a
"weight" heuristic which assigns less value to things like OHCI USB
controllers than, for example SCSI RAID controllers. This algorithm
will probably want some fine tuning for specific devices or device
types.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It advertises "host bridge" instead of "PCI to PCI bridge" which confuses
the Linux probe code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PCI_REASSIGN_ALL_RSRC is set, we used to clear all bus resources
at the beginning of survey and re-allocate them later.
This changes it so instead, during early fixup, we mark all resources
as IORESOURCE_UNSET and move them down to be 0-based.
Later, if bus resources are still unset at the beginning of the survey,
then we clear them.
This shouldn't impact the re-assignment case on 4xx, but will enable
us to have the platform do some custom resource assignment before the
survey, by clearing individual resources IORESOURCE_UNSET bit.
Also limits the clutter in the kernel log from fixup when re-assigning
since we don't care about the offset applied to the BAR values in this
case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some platforms need to perform resource allocation using a custom algorithm
due to HW constraints, or may want to tweak things globally below a host
bridge. For example OPAL support for IODA will need to perform a
resource allocation pass that applies IODA specific segmentation
constraints to MMIO which cannot be done simply using the kernel generic
resource management code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a pgprot combination required by some cache-enabled IO device
mappings, such as Freescale datapath (QMan and BMan) portals.
Signed-off-by: Geoff Thorpe <geoff@geoffthorpe.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All interrupts which must be non threaded are marked
IRQF_NO_THREAD. So it's safe to allow force threaded handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
IPI handlers cannot be threaded. Remove the obsolete IRQF_DISABLED
flag (see commit e58aa3d2) while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cascade handlers must run in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cascade interrupt must run in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RTAS firmware flash update is conducted using an RTAS call that is
serialized by lock_rtas() which uses spin_lock. While the flash is in
progress, rtasd performs scan for any RTAS events that are generated by
the system. rtasd keeps scanning for the RTAS events generated on the
machine. This is performed via workqueue mechanism. The rtas_event_scan()
also uses an RTAS call to scan the events, eventually trying to acquire
the spin_lock before issuing the request.
The flash update takes a while to complete and during this time, any other
RTAS call has to wait. In this case, rtas_event_scan() waits for a long time
on the spin_lock resulting in a soft lockup.
Fix: Just before the flash update is performed, the queued rtas_event_scan()
work item is cancelled from the work queue so that there is no other RTAS
call issued while the flash is in progress. After the flash completes, the
system reboots and the rtas_event_scan() is rescheduled.
Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Signed-off-by: Ravi Nittala <ravi.nittala@in.ibm.com>
Reported-by: Divya Vikas <divya.vikas@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch add the Chroma platform to WSP/PowerEN, which is a PCIe
card (a defconfig is included).
The card includes an H8 service processor that is used to manage the
card. The H8 is connected over the second serial UART on the PowerEN
chip so this patch includes a simple 16550 driver to enable
communication, mostly for "power off" and "rebooting".
This patch also includes a, WSP specific, "halt" method that will shut
of all A2 cores but still leave power on at the chip level. This is
desirable, especially if you wish to interrogate the chip with a
hardware probe after the halt.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 'u' command will print the TLB on book3e parts and the SLB on
Book3s parts, but the help system doesn't say that correctly.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a fault handler that responds to illegal Coprocessor
types. Currently all CTs are treated and illegal. There are two ways
to report the fault back to the application. If the application used
the record form ("icswx.") then the architected "reject" is emulated.
If the application did not used the record form ("icswx") then it is
selectable by config whether the failure is silent (as architected) or
a SIGILL is generated.
In all cases pr_warn() is used to log the bad CT.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ICSWX is also used by the A2 processor to access coprocessors,
although not all "chips" that contain A2s have coprocessors.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some processors, like embedded, that already have a PID register that
is managed by the system. This patch separates the ACOP and PID
processing into separate files so that the ACOP code can be shared.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
... when != of_node_put(e)
when != true e == NULL
when != e2 = e
e = e1
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
... when != of_node_put(e)
when != true e == NULL
when != e2 = e
e = e1
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some pseries IOMMUs cache TCEs but don't snoop when the TCEs are changed
in memory, hence we need manually invalidate in software.
This adds code to do the invalidate. It keys off a device tree property
to say where the to do the MMIO for the invalidate and some information
on what the format of the invalidate including some magic routing info.
it_busno get overloaded with this magic routing info and it_index with
the MMIO address for the invalidate command.
This then gets hooked into the building and freeing of TCEs.
This is only useful on bare metal pseries. pHyp takes care of this when
virtualised.
Based on patch from Milton with cleanups from Mikey.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
decrementer_check_overflow is called from arch_local_irq_restore so
we want to make it as light weight as possible. As such, turn
decrementer_check_overflow into an inline function.
To avoid a circular mess of includes, separate out the two components
of struct decrementer_clock and keep the struct clock_event_device
part local to time.c.
The fast path improves from:
arch_local_irq_restore
0: mflr r0
4: std r0,16(r1)
8: stdu r1,-112(r1)
c: stb r3,578(r13)
10: cmpdi cr7,r3,0
14: beq- cr7,24 <.arch_local_irq_restore+0x24>
...
24: addi r1,r1,112
28: ld r0,16(r1)
2c: mtlr r0
30: blr
to:
arch_local_irq_restore
0: std r30,-16(r1)
4: ld r30,0(r2)
8: stb r3,578(r13)
c: cmpdi cr7,r3,0
10: beq- cr7,6c <.arch_local_irq_restore+0x6c>
...
6c: ld r30,-16(r1)
70: blr
Unfortunately we still setup a local TOC (due to -mminimal-toc). Yet
another sign we should be moving to -mcmodel=medium.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some formatting issues and use the DECREMENTER_MAX
define instead of 0x7fffffff.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The clockevents code uses max_delta_ns to avoid calling a
clockevent with too large a value.
Remove the redundant version of this in the timer_interrupt
code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use clocksource_register_hz which calculates the shift/mult
factors for us. Also remove the shift = 22 assumption in
vsyscall_update - thanks to Paul Mackerras and John Stultz for
catching that.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can use clockevents_calc_mult_shift instead of doing all
the work ourselves.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When re-enabling interrupts we have code to handle edge sensitive
decrementers by resetting the decrementer to 1 whenever it is negative.
If interrupts were disabled long enough that the decrementer wrapped to
positive we do nothing. This means interrupts can be delayed for a long
time until it finally goes negative again.
While we hope interrupts are never be disabled long enough for the
decrementer to go positive, we have a very good test team that can
drive any kernel into the ground. The softlockup data we get back
from these fails could be seconds in the future, completely missing
the cause of the lockup.
We already keep track of the timebase of the next event so use that
to work out if we should trigger a decrementer exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/mm/hugetlbpage.c: In function 'reserve_hugetlb_gpages':
arch/powerpc/mm/hugetlbpage.c:312:2: error: implicit declaration of function 'parse_args'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
define GENERIC_IOMAP in a central location
instead of all architectures. This will be helpful
for the follow-up patch which makes it select
other configs. Code is also a bit shorter this way.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On Freescale parts with multiple MSI controllers, the controllers are
combined into one "pool" of interrupts. Whenever a device requests an MSI
interrupt, the next available interrupt from the pool is selected,
regardless of which MSI controller the interrupt is from. This works
because each PCI bus has an ATMU to all of CCSR, so any PCI device can
access any MSI interrupt register.
The fsl,msi property is used to specify that a given PCI bus should only
use a specific MSI device. This is necessary, for example, with the
Freescale hypervisor, because the MSI devices are assigned to specific
partitions.
Ideally, we'd like to be able to assign MSI devices to PCI busses within
the MSI or PCI layers. However, there does not appear to be a mechanism
to do that. Whenever the MSI layer wants to allocate an MSI interrupt to
a PCI device, it just calls arch_setup_msi_irqs(). It would be nice if we
could register an MSI device with a specific PCI bus.
So instead we remember the phandles of each MSI device, and we use that to
limit our search for an available interrupt. Whenever we are asked to
allocate a new interrupt for a PCI device, we check the fsl,msi property
of the PCI bus for that device. If it exists, then as we are looping over
all MSI devices, we skip the ones that don't have a matching phandle.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1010RDB & P1023RDS can use the new mpc85xx_common_publish_devices().
Also move 'fsl,srio' into the list of standard buses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
85xx board files have a lot of duplication in *_publish_devices()/
*_declare_of_platform_devices() functions. Merge that into a single
function common to most of the boards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Separate handling of CPM2 PIC initialization to mpc85xx_cpm2_pic_init()
function.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Traditionally mpc830x_rdb board file searched for mpc8308-pcie devices.
However both in-kernel dts from the beginning declared those pcie units
as compatible with mpc8314-pci, which is handled by mpc83xx_setup_pci().
Drop special handling for mpc8308 and use common function instead.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Nearly all mpc83xx-based boards have a common piece of code - one that
loops over all pci/pcie bridges and registers them. Merge that code into
a special function common to all boards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
83xx board files have a lot of duplication in
*_declare_of_platform_devices() functions. Merge that into a single
function common to most of the boards.
The only leftover is mpc834x_itx.c board file which explicitly asks for
fsl,pq2pro-localbus, as corresponding bindings don't provide
"simple-bus" compatibility in localbus node.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On mpc83xx platform nearly all _init_IRQ functions look alike. They either
just setup ipic, or setup ipic and QE PIC. Separate this to special functions
to be either referenced from ppc_md, or called from board file.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
In this situation, the pixis supports "indirect mode", which allows access
to the pixis itself by reading/writing addresses on specific local bus
chip selects. CS0 is used to select which pixis register to access, and
CS1 is used to read/write the value.
To support this, we introduce another board-control child node of the
localbus node that contains a 'reg' property for CS0 and CS1. This will
produce the correct physical addresses for CS0 and CS1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Power supply for LBC registers is off when system go to deep-sleep state.
We save the values of registers before suspend and restore to registers
after resume.
We removed the last two reservation arrays from struct fsl_lbc_regs for
allocating less memory and minimizing the memcpy size.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current pci/pcie init code will hide the pci/pcie host resource.
But did not judge it is host/RC or agent/EP. If configured as
agent/EP, we should avoid hiding its resource in the host side.
In PCI system, the Programing Interface can be used to judge the
host/agent status:
Programing Interface = 0: host
Programing Interface = 1: Agent
In PCIE system, both the Programing Interface and Header type can
be used to judge the RC/EP status.
Header Type = 0: EP
Header Type = 1: RC
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update all dts files that support SRIO controllers to match the new
fsl,srio device tree binding.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p5020-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p4080-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3060-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
* Fixed l3-cache IRQs, we have 2 CPCs, so we should have IRQs for both
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Fixed some dcsr compatiable typo's from 'p43041' to 'p3041'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p2041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 &
* etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 & etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1023-IP..." from compatibles for standard blocks
* Removed incorrect power/pmc node, there are no etsec on P1023
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Updated spi node to new espi binding specification
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1022-IP..." from compatibles for standard blocks
* Fixed bug in local bus range node for CS2, was maping to
0x0 0x0xffa00000 instead of 0xf 0xffa00000
* Fixed localbus reg property should have been 0xf 0xffe05000
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Timur Tabi <timur@freescale.com>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Dropping "fsl,p1020-IP..." from compatibles for standard blocks
* Fixed PCIe interrupt-maps to have proper number of cells
* Added mdio node for etsec@26000
* Added usb node for 2nd usb controller
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1010-IP..." from compatibles for standard blocks
* PCI interrupt map - wrong IRQs for PCI-0 controller
* SDHC interrupt sense was wrong
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8572 SoC template
* Dropping "fsl,mpc8572-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Dropping "fsl,mpc8569-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Dropping "fsl,mpc8568-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Moved mdio nodes up one level instead of under tsec nodes
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Added MPIC / PCIe msi node
* Dropping "fsl,mpc8548-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Updated ethernet 'model' to 'eTSEC' as that's what on MPC8544
* Dropping "fsl,mpc8544-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
* and moved
PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8536 SoC template
[ marked as MPC8572 compatiable to get errata handling that applies ]
* Added missing cache-line-size & cache-size properties missing from
L2-cache node
* Added IP level IEEE 1588 / ptp timer node
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce some common components that we can utilize to build up the
various PQ3/85xx device trees.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* set interrupt-parent at root so its not duplicate in every node
* Add mpic timers
* Move to 4-prop cells for mpic timer
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move SoC specific details like irq mapping to SoC dtsi
* Update interrupt property to cover both error interrupt and PCIe
runtime interrupts
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we include the p1020rdb.dts instead of p1020si.dts we greatly reduce
duplication and maintenance. We can just list which devices are
disabled for the given core and mpic protected sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update of_platform_bus_probe() RapidIO node to be compitable with
new RapidIO dts compatible property.
Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Usually, freescale rapidio endpoint can support one or two 1x or 4X
LP-Serial link interfaces, and rapidio message transactions can be
implemented by two message units. This adds the support of two
rapidio ports and initializes message unit 0 and message unit 1. And
these ports and message units can work simultaneously.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PowerPC RapidIO controller consists of a RapidIO endpoint and
a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to
replace the RMU in DPAA architecture. Therefore, we should split the code
into two function modules according to the hardware architecture. Add new
struct for RMU module, and new initialization function to set up RMU
module. This policy is very conducive to adding new module like RMan, or
adding multi-ports or message units support.
Signed-off-by: Lian Minghuan <Minghuan.Lian@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
At this point, ehv_pic has been allocated but not stored anywhere, so it
should be freed before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If Freescale LBC driver fails to initialise itself from device tree, then
internal structure is freed only but not NULL-fied. As result functions
fsl_lbc_find() after checking the structure is not NULL are trying to
access device registers.
Signed-off-by: Alexandre Rusev <arusev@dev.rtsoft.ru>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
QE_General4 should only round up the divisor iff divisor is > 3.
Rounding up lower divisors makes the error too big, causing USB
on MPC832x to fail.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/p3060_qds.c: In function '__machine_initcall_p3060_qds_declare_of_platform_devices':
arch/powerpc/platforms/85xx/p3060_qds.c:73:1: error: implicit declaration of function 'declare_of_platform_devices'
declare_of_platform_devices should have been corenet_ds_publish_devices.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver for the Freescale P3060 QDS got added by commit 96cc017c5b
("[...] Add support for P3060QDS board"). Its Kconfig entry selects
MPC8xxx_GPIO. But at the time that driver got added MPC8xxx_GPIO was
already renamed to GPIO_MPC8XXX, by commit c68308dd50 ("gpio: move
mpc8xxx/512x gpio driver to drivers/gpio").
So make this driver select GPIO_MPC8XXX.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers. As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).
IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
This reverts commit a15bd354f0.
It exceeded the padding on the SREGS struct, rendering the ABI
backwards-incompatible.
Conflicts:
arch/powerpc/kvm/powerpc.c
include/linux/kvm.h
Signed-off-by: Avi Kivity <avi@redhat.com>
On PPC64, put_sigset_t converts a sigset_t to a compat_sigset_t
before copying it to userspace. There is a typo in the case that
we have 4 words to copy, meaning that we corrupt the compat_sigset_t.
It appears that _NSIG_WORDS can't be greater than 2 at the moment
so this code is probably always optimised away anyway.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Documentation/memory-barriers.txt document requires that atomic
operations that return a value act as a memory barrier both before
and after the actual atomic operation.
Our current implementation doesn't guarantee this. More specifically,
while a load following the isync can not be issued before stwcx. has
completed, that completion doesn't architecturally means that the
result of stwcx. is visible to other processors (or any previous stores
for that matter) (typically, the other processors L1 caches can still
hold the old value).
This has caused an actual crash in RCU torture testing on Power 7
This fixes it by changing those atomic ops to use new macros instead
of RELEASE/ACQUIRE barriers, called ATOMIC_ENTRY and ATMOIC_EXIT barriers,
which are then defined respectively to lwsync and sync.
I haven't had a chance to measure the performance impact (or rather
what I measured with kernel compiles is in the noise, I yet have to
find a more precise benchmark)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Recent binutils refuses to assemble AltiVec opcodes when in e500/SPE
mode, as some of those opcodes alias the "SPE" instructions. This
triggers an ancient binutils version check even when building a kernel
with CONFIG_ALTIVEC disabled.
In theory, the check could be conditionalized on CONFIG_ALTIVEC, but in
practice it has long outlived its utility. It is virtually impossible
to find binutils older than 2.12.1 (released 2002) in the wild anymore.
Even ancient RedHat Enterprise Linux 4 has binutils-2.14.
To fix the kernel build when done natively on e500 systems with this new
binutils, the test is simply removed.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the introduction of CONFIG_PPC_ADV_DEBUG_REGS user space debug is
broken on Book-E 64-bit parts that support delayed debug events. When
switch_booke_debug_regs() sets DBCR0 we'll start getting debug events as
MSR_DE is also set and we aren't able to handle debug events from kernel
space.
We can remove the hack that always enables MSR_DE and loads up DBCR0 and
just utilize switch_booke_debug_regs() to get user space debug working
again.
We still need to handle critical/debug exception stacks & proper
save/restore of state for those exception levles to support debug events
from kernel space like we have on 32-bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All of DebugException is already protected by CONFIG_PPC_ADV_DEBUG_REGS
there is no need to have another such ifdef inside the function.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had an existing ifdef for 4xx & BOOKE processors that got changed to
CONFIG_PPC_ADV_DEBUG_REGS. The define has nothing to do with
CONFIG_PPC_ADV_DEBUG_REGS. The define really should be:
#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
and not
#ifdef CONFIG_PPC_ADV_DEBUG_REGS
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the PS3 IPI message setup from ps3_smp_setup_cpu() to ps3_smp_probe().
Fixes startup warnings like these:
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2649
Modules linked in:
...
---[ end trace 31fd0ba7d8756001 ]---
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes the PS3 bootup hang introduced in 3.0-rc1 by:
commit 317f394160
sched: Move the second half of ttwu() to the remote cpu
Move the PS3's LV1 EOI call lv1_end_of_interrupt_ext() from ps3_chip_eoi()
to ps3_get_irq() for IPI messages.
If lv1_send_event_locally() is called between a previous call to
lv1_send_event_locally() and the coresponding call to
lv1_end_of_interrupt_ext() the second event will not be delivered to the
target cpu.
The PS3's SMP IPIs are implemented using lv1_send_event_locally(), so if two
IPI messages of the same type are sent to the same target in a relatively
short period of time the second IPI event can become lost when
lv1_end_of_interrupt_ext() is called from ps3_chip_eoi().
CC: stable@kernel.org
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If you build with KVM and UP it fails with the following due to a
missing include.
/arch/powerpc/kvm/book3s_hv.c: In function 'do_h_register_vpa':
arch/powerpc/kvm/book3s_hv.c:156:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:156:10: note: each undeclared identifier is reported only once for each function it appears in
arch/powerpc/kvm/book3s_hv.c:192:12: error: 'H_RESOURCE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:222:9: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c: In function 'kvmppc_pseries_do_hcall':
arch/powerpc/kvm/book3s_hv.c:228:30: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:232:7: error: 'H_CEDE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:234:7: error: 'H_PROD' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:238:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:250:7: error: 'H_CONFER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:252:7: error: 'H_REGISTER_VPA' undeclared (first use in this function)
make[2]: *** [arch/powerpc/kvm/book3s_hv.o] Error 1
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@kernel.org (3.1 only)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
kdump fails because we try to execute an HV only instruction. Feature
fixups are being applied after we copy the exception vectors down to 0
so they miss out on any updates.
We have always had this issue but it only became critical in v3.0
when we added CFAR support (breaks POWER5) and v3.1 when we added
POWERNV (breaks everyone).
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> [v3.0+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I had to debug a strange situation where all manner of things were
failing. SMT threads, storage and network were all completely broken.
The root cause was we couldn't find enough memory to instantiate RTAS -
this was a network install so the initrd was huge.
Instead of limping along and failing in mysterious ways we should just
panic up front if RTAS exists and we can't allocate space for it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kexec is not supported on 47x. 47x is a variant of 44x with slightly
different MMU and SMP support. There was a typo in the config dependency
for kexec. This patch fixes the same.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Should do what other architectures do and wrap all that code into
the appropriate ifdef
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The "#include <linux/module.h>" was replaced by "#include <linux/export.h>"
in the patch "powerpc: various straight conversions from module.h --> export.h".
This will cause the following compile problem:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:296: error: implicit declaration of function 'search_exception_tables'.
The file fsl_rio.c needs the declaration of function "search_exception_tables"
in the header file "linux/module.h".
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Benjamin Herrenschmidt