Setup the GPIO7_11 pin as interrupt to the DA9053 and also rename the regulator nodes
so that they match with the datasheet.
This allows probing of DA9053 to succeed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.2: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to Documentation/devicetree/bindings/mmc/mmc.txt bus-width
is a mandatory property. While this is currently enforced nowhere, it's
a good habit to just add the property now to allow to add common helper
functionality for the mmc property parsing later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With being part of multi-platform support, SMP can be enabled by other
platform even when SOC_IMX6Q is deselected. It leads to a situation
that arch/arm/mach-imx/platsmp.c is built without HAVE_IMX_SRC selection
which will cause build error. For example, the following link errors
will be seen when building imx5 with other v7 platforms.
arch/arm/mach-imx/built-in.o: In function `imx_cpu_die':
platform-ahci-imx.c:(.text+0x219c): undefined reference to `imx_enable_cpu'
arch/arm/mach-imx/built-in.o: In function `imx_boot_secondary':
platform-ahci-imx.c:(.cpuinit.text+0x14): undefined reference to `imx_set_cpu_jump'
platform-ahci-imx.c:(.cpuinit.text+0x20): undefined reference to `imx_enable_cpu'
Select HAVE_IMX_SRC as long as SMP is enabled to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit c5a0d497(ARM: imx: enable multi-platform build),
ARCH_MXC is selected by the following logic:
config ARCH_MXC
def_bool y if ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7
, which causes build error on vexpress_defconfig:
arch/arm/mach-imx/hotplug.c:49: undefined reference to `imx_enable_cpu'
arch/arm/mach-imx/platsmp.c:57: undefined reference to `imx_set_cpu_jump'
arch/arm/mach-imx/platsmp.c:58: undefined reference to `imx_enable_cpu'
Make ARCH_MXC a user selectable option, so that it does not get built
by default on other defconfigs that select ARCH_MULTI_V4_V5 or ARCH_MULTI_V6_V7.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It enables multi-platform build for imx. With ARCH_MULTI_* options
coming to play, ARCH_MXC becomes an user invisible option, while
ARCH_IMX_V4_V5 and ARCH_IMX_V6_V7 get removed. Both imx_v4_v5_defconfig
and imx_v6_v7_defconfig get updated to adopt the changes.
AUTO_ZRELADDR and ARM_PATCH_PHYS_VIRT are selected by ARCH_MXC now to
save the duplication.
Headers timex.h and uncompress.h are not needed for multi-platform
build. Remove them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mxc_device_init() is a core_initcall function used to register devices
for mxc_aips_bus and mxc_ahb_bus, which are needed by gpio and dma
device registration.
Instead of being a core_initcall function, we have it called in soc
specific initialization function before gpio and dma devices get
registered, so that it will not be called for other platforms when
we enable multi-platform support for imx.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The only mach/irqs.h user outside arch/arm/mach-imx is
sound/soc/fsl/imx-pcm-fiq.c, which refers to mxc_set_irq_fiq().
Move the declaration into include/linux/platform_data/asoc-imx-ssi.h,
so that we can remove mach/irqs.h includsion from imx-pcm-fiq.c.
Inside arch/arm/mach-imx, the only users to mach/irqs.h are avic.c
and tzic.c for referring to macro FIQ_START. Let's move the macro
into irq-common.h and get rid of mach/irqs.h completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
It moves a bunch of header files included in hardware.h and itself
from mach-imx/include/mach to mach-imx, and updates users to include
hardware.h rather than mach/hardware.h. The files in mach-imx/devices
will need to include "../hardware.h".
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Move imx debug-macro.S over to common debug macro directory. It
removes the inclusion to hardware.h by hard-coding the physical
address of uart port and copying IMX_IO_P2V from hardware.h.
Since we will need a common solution, which might use a fixed virtual
address for uart port across platforms, we make a copy of IMX_IO_P2V
here as a temporary solution to enable low-level debug for imx
multi-platform build.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chris Ball <cjb@laptop.org>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: linux-mmc@vger.kernel.org
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: linux-media@vger.kernel.org
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Retrieve MEM and IRQ from resources rather than directly using the
value by including machine header.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: rtc-linux@googlegroups.com
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.
The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version. It also updates
the platform code and device tree source accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
The inclusion of mach/hardware.h is not used by the driver at all.
Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
The inclusion of mach/hardware.h is not used by the driver at all.
Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
The inclusion of mach/hardware.h is not used by the driver at all.
Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
The inclusion of mach/hardware.h is not used by the driver at all.
Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
The inclusion of mach/hardware.h is not used in imx-sdma driver at all.
Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
The header ipu.h really belongs to dma subsystem rather than imx
platform. Rename it to ipu-dma.h and put it into include/linux/dma/.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-media@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
The header mach/dma-mx1-mx2.h is used nowhere. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/ulpi.h to mach-imx/ulpi.h, and update
users to include ulpi.h rather than mach/ulpi.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/iram.h to mach-imx/iram.h, and update users
to include iram.h rather than mach/iram.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/iim.h to mach-imx/iim.h, and update users
to include iim.h rather than mach/iim.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/cpuidle.h to mach-imx/cpuidle.h, and
update users to include cpuidle.h rather than mach/cpuidle.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/common.h to mach-imx/common.h and update
all users to include common.h rather than mach/common.h.
It also removes an unneeded inclusion to common.h in
mach-imx/devices/devices.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It's really unnecessary to have plat-mxc, and let's merge it into
mach-imx. It's pretty much just a bunch of file renaming and
Kconfig/Makefile merge.
To make the change less invasive, we keep using Kconfig symbol
CONFIG_ARCH_MXC for mach-imx sub-architecture.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It moves platform device code from plat-mxc into mach-imx. Along with
that, header devices-common.h gets moved from plat-mxc/include/mach/
into mach-imx/devices/.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
There is no need for device-imx*.h to include <soc>.h. Remove them
and fix one indirect inclusion in mach-mx31ads.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The board files in mach-imx are the only users of iomux drivers and
headers. Move them into mach-imx from plat-mxc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The headers that are only used by board files do not necessarily
need to be in plat-mxc/include/mach. Move them to the same place
as those board files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h. But commit abbf1590de ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.
This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.
It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UAPI commits forgot to test tooling builds such as tools/perf/,
and this fixes the fallout.
Manual conversion.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM update from Russell King:
"This is the final round of stuff for ARM, left until the end of the
merge window to reduce the number of conflicts. This set contains the
ARM part of David Howells UAPI changes, and a fix to the ordering of
'select' statements in ARM Kconfig files (see the appropriate commit
for why this happened - thanks to Andrew Morton for pointing out the
problem.)
I've left this as long as I dare for this window to avoid conflicts,
and I regenerated the config patch yesterday, posting it to our
mailing list for review and testing. I have several acks which
include successful test reports for it.
However, today I notice we've got new conflicts with previously unseen
code... though that conflict should be trivial (it's my changes vs a
one liner.)"
* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate arch/arm/include/asm
Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUHk+/xOxKuMESys7AQIfgRAAkl0t/8YNaKVIGmO0TCXf1kn978pQqYcj
3IzUP+U+aybLEpU3TxW6CNUh1r5w5AX5ctTE20CWeQ6ViGcR7rgYOabZ4NtcelLH
x+QlljYnFvZrymmuyhVMQiNfcnFAq0BNAEUeqjM4uxgLiG4Q4ScG0Cyo3yT8yjFr
9760e7JpcbdO0G2Ce7IhzdS6TBRgc+UeSpxpQAzDBoDx7UTArsKHiUIhyHB6thXG
9+bSl4gPRpTpLGXK7ftxDu/E35+utJcSpMH8ZAFIcex2ZPWpMKcBqnDWN+9GvKWy
5NYARZxVCy2FL54zbUm4sLqIrYTS8z4dRJ8MYhi+YIJsrMnANbzasYiZ07PZlJss
Vh6u3wfy0k/e4kQUmf/eY8p5U0HoN0JNPeZbPP78WdljEq3B+h5k42HAVHg8MsiF
oC7WYcNiAz2fcnpmc7e5Fxua4bPT71mv9Vytq5w5R4juXcBnttmxv0JZAHyT9gsr
W7ziYSrh84q5kg4YAIeogukDcKxUEORxR3ha+5AynymhbLJyQV0gDdc9skTcZrWN
TeuNLCxW5odGOtCUr/gsSeWqsapXfa4DhURahTDSqgQ+kuqKbWh/ozPV18SODw9q
VB72jeujVUfwUaVPqyrpLkrbGUcXMMYsFBJFvwGIm45zygs7n/WU5kI6/2KkfVHS
Py6oqVU6m4E=
=Tnxe
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers
Pull UAPI disintegration for include/linux/{,byteorder/}*.h from David Howells:
"The patches contained herein do the following:
(1) Remove kernel-only stuff in linux/ppp-comp.h from the UAPI. I checked
this with Paul Mackerras before I created the patch and he suggested some
extra bits to unexport.
(2) Remove linux/blk_types.h entirely from the UAPI as none of it is userspace
applicable, and remove from the UAPI that part of linux/fs.h that was the
reason for linux/blk_types.h being exported in the first place. I
discussed this with Jens Axboe before creating the patch.
(3) The big patch of the series to disintegrate include/linux/*.h as a unit.
This could be split up, though there would be collisions in moving stuff
between the two Kbuild files when the parts are merged as that file is
sorted alphabetically rather than being grouped by subsystem.
Of this set of headers, 17 files have changed in the UAPI exported region
since the 4th and only 8 since the 9th so there isn't much change in this
area - as one might expect.
It should be pretty obvious and straightforward if it does come to fixing
up: stuff in __KERNEL__ guards stays where it is and stuff outside moves
to the same file in the include/uapi/linux/ directory.
If a new file appears then things get a bit more complicated as the
"headers +=" line has to move to include/uapi/linux/Kbuild. Only one new
file has appeared since the 9th and I judge this type of event relatively
unlikely.
(4) A patch to disintegrate include/linux/byteorder/*.h as a unit.
Signed-off-by: David Howells <dhowells@redhat.com>"
* tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/byteorder
UAPI: (Scripted) Disintegrate include/linux
UAPI: Unexport linux/blk_types.h
UAPI: Unexport part of linux/ppp-comp.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3RHN
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers
Pull spi UAPI disintegration from David Howells:
"This is to complete part of the Userspace API (UAPI) disintegration
for which the preparatory patches were pulled recently. After these
patches, userspace headers will be segregated into:
include/uapi/linux/.../foo.h
for the userspace interface stuff, and:
include/linux/.../foo.h
for the strictly kernel internal stuff.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>"
* tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/spi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlB5ASYACgkQ70gcjN2673OFxgCfTE7Pa4HBDe0lLDVUXfAgH/Va
OeQAoM+MCMC/rgzmuB8jtDIldvgnC7eA
=zkR2
-----END PGP SIGNATURE-----
Merge tag 'openrisc-uapi' of git://openrisc.net/jonas/linux
Pull OpenRISC uapi disintegration from Jonas Bonn:
"OpenRISC UAPI disintegration work from David Howells"
* tag 'openrisc-uapi' of git://openrisc.net/jonas/linux:
UAPI: (Scripted) Disintegrate arch/openrisc/include/asm
Pull user namespace compile fixes from Eric W Biederman:
"This tree contains three trivial fixes. One compiler warning, one
thinko fix, and one build fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
btrfs: Fix compilation with user namespace support enabled
userns: Fix posix_acl_file_xattr_userns gid conversion
userns: Properly print bluetooth socket uids
"discard" support, some dm-raid improvements and other assorted
bits and pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=XRmL
-----END PGP SIGNATURE-----
Merge tag 'md-3.7' of git://neil.brown.name/md
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
The large platform selection choice should be sorted by option string
so it's easy to find the platform you're looking for. Fix the few
options which are out of this order.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fabio Estevam