We now get a link failure when CONFIG_INET is disabled, since
tcp_gro_complete is unavailable:
drivers/net/ethernet/hisilicon/hns3/hns3_enet.o: In function `hns3_set_gro_param':
hns3_enet.c:(.text+0x230c): undefined reference to `tcp_gro_complete'
Add an explicit CONFIG_INET dependency here to avoid the broken
configuration.
Fixes: a6d53b97a2 ("net: hns3: Adds GRO params to SKB for the stack")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
Introduce NETDEV_PRE_CHANGEADDR
Spectrum devices have a limitation that all router interfaces need to
have the same address prefix. In Spectrum-1, the requirement is for the
initial 38 bits of all RIFs to be the same, in Spectrum-2 the limit is
36 bits. Currently violations of this requirement are not diagnosed. At
the same time, if the condition is not upheld, the mismatched MAC
address ends up overwriting the common prefix, and all RIF MAC addresses
silently change to the new prefix.
It is therefore desirable to be able at least to diagnose the issue, and
better to reject attempts to change MAC addresses in ways that is
incompatible with the device.
Currently MAC address changes are notified through emission of
NETDEV_CHANGEADDR, which is done after the change. Extending this
message to allow vetoing is certainly possible, but several other
notification types have instead adopted a simple two-stage approach:
first a "pre" notification is sent to make sure all interested parties
are OK with the change that's about to be done. Then the change is done,
and afterwards a "post" notification is sent.
This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore this patchset introduces it for NETDEV_CHANGEADDR as well.
One prominent path to emitting NETDEV_CHANGEADDR is through
dev_set_mac_address(). Therefore in patch #1, give this function an
extack argument, so that a textual reason for rejection (or a warning)
can be communicated back to the user.
In patch #2, add the new notification type. In patch #3, have dev.c emit
the notification for instances of dev_addr change, or addition of an
address to dev_addrs list.
In patches #4 and #5, extend the bridge driver to handle and emit the
new notifier.
In patch #6, change IPVLAN to emit the new notifier.
Likewise for bonding driver in patches #7 and #8. Note that the team
driver doesn't need this treatment, as it goes through
dev_set_mac_address().
In patches #9, #10 and #11 adapt mlxsw to veto MAC addresses on router
interfaces, if they violate the requirement that all RIF MAC addresses
have the same prefix.
Finally in patches #12 and #13, add a test for vetoing of a direct
change of a port device MAC, and indirect change of a bridge MAC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a FID RIF is created for a bridge with IP address, its MAC address
must obey the same requirements as other RIFs. Test that attempts to
change the address incompatibly by attaching a device are vetoed with
extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that attempts to change address in a way that violates Spectrum
requirements are vetoed with extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On NETDEV_PRE_CHANGEADDR, if the change is related to a RIF interface,
verify that it satisfies the criterion that all RIF interfaces have the
same MAC address prefix, as indicated by mlxsw_sp.mac_mask.
Additionally, besides explicit address changes, check that the address
of an interface for which a RIF is about to be added matches the
required pattern as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum hardware demands that all router interfaces in the system
have the same first 38 resp. 36 bits of MAC address: the former limit
holds on Spectrum, the latter on Spectrum-2. Add a field that refers to
the required prefix mask and initialize in mlxsw_sp1_init() and
mlxsw_sp2_init().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare mlxsw_sp_netdevice_router_port_event() for handling of
NETDEV_PRE_CHANGEADDR. Split out the part that deals with the actual
changes and call it for the two events currently handled.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give interested parties an opportunity to veto an impending HW address
change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before NETDEV_CHANGEADDR, bond driver should emit NETDEV_PRE_CHANGEADDR,
and allow consumers to veto the address change. To propagate further the
return code from NETDEV_PRE_CHANGEADDR, give the function that
implements address change a return value.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A NETDEV_CHANGEADDR event implies a change of address of each of the
IPVLANs of this IPVLAN device. Therefore propagate NETDEV_PRE_CHANGEADDR
to all the IPVLANs.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port device seeks approval of a potential new MAC address, make
sure that should the bridge device end up using this address, all
interested parties would agree with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is attached to a bridge, the address of the bridge in
question may change as well. Even if it would not change at this
point (because the current bridge address is lower), it might end up
changing later as a result of detach of another port, which can't be
vetoed.
Therefore issue NETDEV_PRE_CHANGEADDR regardless of whether the address
will be used at this point or not, and make sure all involved parties
would agree with the change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device address is about to be changed, or an address added to the
list of device HW addresses, it is necessary to ensure that all
interested parties can support the address. Therefore, send the
NETDEV_PRE_CHANGEADDR notification, and if anyone bails on it, do not
change the address.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETDEV_CHANGEADDR notification is emitted after a device address
changes. Extending this message to allow vetoing is certainly possible,
but several other notification types have instead adopted a simple
two-stage approach: first a "pre" notification is sent to make sure all
interested parties are OK with a change that's about to be done. Then
the change is done, and afterwards a "post" notification is sent.
This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore adopt it for NETDEV_CHANGEADDR as well.
To that end, add NETDEV_PRE_CHANGEADDR and an info structure to go along
with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Eli Britstein,
Patches 1-10 adds remote mirroring support.
Patches 1-4 refactor encap related code as pre-steps for using per
destination encapsulation properties.
Patches 5-7 use extended destination feature for single/multi
destination scenarios that have a single encap destination.
Patches 8-10 enable multiple encap destinations for a TC flow.
From, Daniel Jurgens,
Patch 11, Use CQE padding for Ethernet CQs, PPC showed up to a 24%
improvement in small packet throughput
From Eyal Davidovich,
patches 12-14, FW monitor counter support
FW monitor counters feature came to solve the delayed reporting of
FW stats in the atomic get_stats64 ndo, since we can't access the
FW at that stage, this feature will enable immediate FW stats updates
in the driver via fw events on specific stats updates.
Patch 12, cleanup to avoid querying a FW counter when it is not
supported
Patch 13, Monitor counters FW commands support
Patch 14, Use monitor counters in ethernet netdevice to update FW
stats reported in the atomic get_stats64 ndo.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcEEYmAAoJEEg/ir3gV/o+XlIIAKIQhvHnCoGMPsZU+HbA1h3O
10i2hnmQqx2F5Z7tSON9jr9HVzLj6FqQ3pSnTyw8xiMBqOldF6abmfpMPQ/XeWXk
PDBCzfOUMAlIsGFAJ06tcz3VLkWrEdoQHmi7Jb4IW+LC9CnZBobzrcLaxQ95txYP
LkCfO8Y70D5tzBrzL1o1RfKsCSFJma5zhXDPF/B3rifLyHOmo9aLzZuDvKwvvSkC
Y3QM5ulnLqVhxaXA0xzB+iHLiI0nX2H17CBPseLzM+Ip0vZS/nA77rnQ49PUgjiZ
d1BoXo9MUa3eoQwXNl+qSAfnGjCwqzplXxzjT2bKKXVc2ZOWmkECgRXmKI6JDDU=
=EuqQ
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-12-11' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-12-11
From Eli Britstein,
Patches 1-10 adds remote mirroring support.
Patches 1-4 refactor encap related code as pre-steps for using per
destination encapsulation properties.
Patches 5-7 use extended destination feature for single/multi
destination scenarios that have a single encap destination.
Patches 8-10 enable multiple encap destinations for a TC flow.
From, Daniel Jurgens,
Patch 11, Use CQE padding for Ethernet CQs, PPC showed up to a 24%
improvement in small packet throughput
From Eyal Davidovich,
patches 12-14, FW monitor counter support
FW monitor counters feature came to solve the delayed reporting of
FW stats in the atomic get_stats64 ndo, since we can't access the
FW at that stage, this feature will enable immediate FW stats updates
in the driver via fw events on specific stats updates.
Patch 12, cleanup to avoid querying a FW counter when it is not
supported
Patch 13, Monitor counters FW commands support
Patch 14, Use monitor counters in ethernet netdevice to update FW
stats reported in the atomic get_stats64 ndo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_LICENSE info to fix this:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.o
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_vport_rep_load':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:1490:21: warning:
variable 'upriv' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_vport_rep_unload':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:1557:21: warning:
variable 'upriv' set but not used [-Wunused-but-set-variable]
It not used any more since commit ef381359e3 ("net/mlx5e: Replace egdev with
indirect block notifications"). Also remove unused variable 'uplink_rpriv'
after this change.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
Pass extack to SWITCHDEV_PORT_OBJ_ADD
Drivers may need to do validation as a result of port object addition.
An example is mlxsw, which needs to check the configuration of a VXLAN
device attached to an offloaded bridge. Without a mapped VLAN, the
invalidity of the device is not important, but as soon as a pvid,
untagged VLAN is configured for the device, it has to be validated and
offloaded. Should the validation fail, there's currently no way to
communicate details of the failure to the user, beyond an error number.
Because currently, extack is not available at all in that area of code,
this patch starts down at the RTNL level and progresses up towards the
driver(s).
In patch #1, ndo_bridge_setlink is updated to include extack, and
callbacks of all clients are updated as well (ignoring the argument).
In patch #2, the bridge driver is updated to propagate the extack
through to the switchdev border, br_switchdev_port_vlan_add().
Patches #3, #4 and #5 then gradually extend switchdev to pass the extack
argument through to the switchdev blocking notifier chain.
Patches #6 and #7 then update mlxsw to pass the extack argument from
VXLAN events resp. port events on to mlxsw_sp_bridge_8021q_vxlan_join().
Finally in patches #8 and #9, the code paths from the previous two
patches are verified to yield an error message.
v2:
- Patch #1:
- In ndo_bridge_setlink(), keep the whole extack declaration on the
same line.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test mapping a VLAN at a port device such that on the same VLAN, there
already is an unoffloadable VXLAN device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test mapping a VLAN at a VXLAN device that can't be offloaded.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After switchdev_handle_port_obj_add() was extended in a preceding patch,
mlxsw_sp_port_obj_add() now takes an extack argument. Propagate it
further by extending a callee chain from mlxsw_sp_port_vlans_add(), via
mlxsw_sp_bridge_port_vlan_add() via mlxsw_sp_port_vlan_bridge_join() via
mlxsw_sp_port_vlan_fid_join() to mlxsw_sp_bridge_ops.fid_get, adding an
extack argument for each of them.
This code path is used when a VLAN is added to a port netdevice if there
already is an unoffloadable VXLAN device with that VLAN mapped.
mlxsw_sp_bridge_8021d_port_join() is updated to obey the new interfaces
changed by the abovementioned code, propagating extack ultimately from
NETDEV_CHANGEUPPER events.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that VLAN port object addition notifications carry an extack,
propagate it from mlxsw_sp_switchdev_vxlan_vlans_add() through
mlxsw_sp_switchdev_vxlan_vlan_add() to
mlxsw_sp_bridge_8021q_vxlan_join().
This code path is used when a VLAN is added to a VXLAN netdevice that
cannot be offloaded.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers use switchdev_handle_port_obj_add() to handle recursive descent
through lower devices. Change this function prototype to take add_cb
that itself takes an extack argument. Decode extack from
switchdev_notifier_port_obj_info and pass it to add_cb.
Update mlxsw and ocelot drivers which use this helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack to the drivers that need it, add an extack field
to struct switchdev_notifier_info, and an extack argument to the
function call_switchdev_blocking_notifiers(). Also add a helper function
switchdev_notifier_info_to_extack().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, bridge driver has extack argument available to
pass to switchdev. Therefore extend switchdev_port_obj_add() with this
argument, updating all callers, and passing the argument through to
switchdev_port_obj_notify().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink has been updated in the previous patch to have extack
available, and changelink RTNL op has had this argument since the time
extack was added. Propagate both through the bridge driver to eventually
reach br_switchdev_port_vlan_add(), where it will be used by subsequent
patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en 0000:19:00.0 (unregistered net_device) (uninitialized): hwrm
req_type 0x190 seq id 0x6 error 0xffff
The message above is commonly seen when a newer driver is used on
hardware with older firmware. The issue is this message means nothing to
anyone except Broadcom. Remove the message to not confuse users as this
message is really not very informative.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Biao Huang says:
====================
add Ethernet driver support for mt2712
Changes in v6:
modifications according to comments from Rob/Andrew/Sean:
1. use delay_ps instead of delay stage.
2. add comments in driver to avoid confusion.
2. rewrite set_delay function.
3. modify binding document for properties: tx-delay-ps/rx-delay-ps/pericfg etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the device tree binding documentation for the MediaTek DWMAC
found on MediaTek MT2712.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Ethernet support for MediaTek SoCs from the mt2712 family
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Add Spectrum-2 multicast routing support
Nir says:
In Spectrum the firmware provided an abstraction for multicast routing
on top of the policy engine. In Spectrum-2 this is no longer the case
and the driver must interact directly with the policy engine in order to
program multicast routes. Every route is written as an ACL rule, its
priority set according to route type (*,G) or (S,G) and its action is an
appropriate multicast routing action. Multicast routes are written to a
specific ACL group which is bound to the appropriate IP protocol
IPv4/IPv6.
Patch #1 adds PEMRBT register needed to declare which ACL group is
dedicated for each IP protocol multicast routing function.
Patch #2 Changes initialization order and puts ACL before router as
multicast router now uses ACL module.
Patch #3 adds Spectrum-2 ACL keys needed for multicast route matching.
Patch #4 adds another ACL profile - in addition to existing flower
profile - which allows the multicast routing module to program rules
directly into the ACL block.
Patch #5 adds the ability to update ACL rules' action, since multicast
routes actions may be updated after being configured.
Patch #6 separates rule creation operation and rule action creation
operation as in multicast router the action is created before the route
is inserted.
Patch #7 sharpens priority handling in Spectrum-2, to ensure incorrect
values are not set to rule's priority.
Patch #8 adds the implementation of multicast routing for IPv4 and IPv6
over existing ACL rule programming
Finally, patch #9 adds a test for IPv4/IPv6 multicast routing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic testing for both IPv4 and IPv6 multicast. The test creates
an (S,G) type route, sends traffic and verifies traffic arrives when the
route is present and then verifies traffic does not arrive after deleting
the route.
This test requires smcroute - https://github.com/troglobit/smcroute which
is a tool that allows creation of static multicast routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation of Spectrum-2 multicast routes for both IPv4 and IPv6 by
using ACL module explicitly.
In Spectrum-2, multicast routes are set as ACL rules, so initialization
takes care of creating dedicated ACL groups and binding them to the
appropriate multicast routing protocol IPv4/IPv6, and afterwards routes
configuration translates to setting explicit ACL rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, higher priority value wins and priority valid values are in
the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts
from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up
until now tc flower did not provide priority 0 or reached the maximal
value, however multicast routing does provide priority 0.
Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in
the correct range. Make sure priority is never set to zero and never
exceeds the maximal allowed value.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, when ACL rule was created its action was created with it.
It suits well for tc flower where ACL rule always needs an action, however
it does not suit multicast router, where the action is created prior to
setting a route, which in Spectrum-2 is actually an ACL rule.
Add support for rule creation without action creation. Do it by adding
afa_block argument to mlxsw_sp_acl_rule_create, which if NULL then an
action would be created, also add an indication within struct
mlxsw_sp_acl_rule_info that tells if the action should be destroyed when
the rule is destroyed.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast routes actions may be updated after creation. An example for that
is an addition of an egress interface to an existing route.
So far, as tc flower API dictated, ACL rules were either created or
deleted. Since multicast routes in Spectrum-2 are written to ACL as any
rule, it is required to allow the update of a rule's action as it may
change.
Add methods and operations to support updating rule's action. This is
supported only for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add specific ACL operations needed for programming multicast routing ACL
groups and routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add virtual router ID fields to Spectrum-2 key blocks set, as the field is
required for multicast routing.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, MC routing is implemented using ACL block explicitly, so
router initialization should take place after ACL initialization.
Set the initialization of the ACL block before IP router initizalization
takes place, so multicast router will be able to allocate ACL data
structures and create its required chains.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, multicast routing is implemented explicitly using policy
engine (ACL) block. PEMRBT register is used to bind a dedicated ACL group
to a specific IP protocol.
Add the register to be later used in multicast router implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to schedule a different tasklet for refill,
This patch remove it.
Suggested-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Adding new notifier block (struct mlx5_nb) monitor_counters_nb
for handeling MONITOR_COUNTER new event type.
- Adding work queue element: monitor_counters_work for re-arm and
update stats.
- We re-queue the update stat work, only when working over firmware
that doesn't support the monitored counters.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
new file monitor_stats.c for the new API.
add arm_monitor_counter new command support.
add set_monitor_counter new command support.
The device can monitor specific counters and provide an event to notify
when these counters are changed.
The monitoring is done in best effort manner where the minimum
notification period is 200 ms, however when the device is loaded, the
notification might be delayed.
To configure the required counters to be monitored, the
SET_MONITOR_COUNTER command shall be used with a list of counters to be
monitored.
The device firmware can monitor up to HCA_CAP.max_num_of_monitor_counters.
The configuration is done based on counter type (such as ppcnt, q counter,
etc) and additional param according to the type of counter selected.
Upon monitor counter change, the device will generate
Monitor_Counter_Change event.
The device will not generate new events unless the driver re-arms the
monitoring functionality, using the ARM_MONITOR_COUNTER command.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Writing 64B CQEs to 128B cache lines results in a RMW operation. Padding
the CQEs to 128B if possible improves performance on 128B cache line
systems like PPC.
Testing on PPC showed up to a 24% improvement in small packet throughput
vs the default behavior, depending on the workload and system topology.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a flow is associated with a single encap structure. The FW
extended destination features enables the driver to associate a flow
with multiple encap instances.
Change the encap id field from a flow scope to a per destination value
in the flow attributes struct. Use the encaps array to associate a flow
table entry with multiple encap entries.
Update the neigh logic to offload only if all encapsulations used in a
flow are connected, and un-offload upon the first one disconnected.
Note that the driver can now support up to two encap destinations.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a flow can be associated with a single encap entry. The
extended destination feature enables the driver to configure multiple
encap entries per flow.
Change the encap flow association field to array as a pre-step towards
supporting multiple encap destinations. Use only the first array
element, with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Arnd Bergmann