Move the code to check whether we've reached the host controller's limit
on the number of endpoints out of the two conditional statements, to
remove duplicate code.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "port" field in xhci_virt_dev stores the port number associated with
one of the two xHCI split roothubs, not the unique port number the xHCI
hardware uses. Since we'll need to store the real hardware port number in
future patches, rename this field to "fake_port".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some alternate interface settings have no endpoints associated with them.
This shows up in some USB webcams, particularly the Logitech HD 1080p,
which uses the uvcvideo driver. If a driver switches between two alt
settings with no endpoints, there is no need to issue a configure endpoint
command, because there is no endpoint information to update.
The only time a configure endpoint command with just the add slot flag set
makes sense is when the driver is updating hub characteristics in the slot
context. However, that code never calls xhci_check_bandwidth, so we
should be safe not issuing a command if only the slot context add flag is
set.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch enables DMA mode1 for the RX path when we know
there won't be any short packets. We check that by looking
into the short_no_ok flag, if it's true we enable mode1, otherwise
we use mode0 to transfer the data.
This will result in a throughput performance gain of around
40% for USB mass-storage/mtp use cases.
[ balbi@ti.com : updated commit log and code comments slightly ]
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Tested-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On Audio class, the wLength field of the Setup
packet, contains the data payload size of the
following Data phase. Instead of harcoding values,
use wLength.
This also fixes a bug where Gadget driver had to
receive 3 bytes, but it was queueing a ZLP.
Signed-off-by: Felipe Balbi <balbi@ti.com>
While testing g_audio with HighSpeed UDC on a
FS Hub, we had no configurations to present to
the host. That's because both speeds where
mutually exclusive.
Signed-off-by: Felipe Balbi <balbi@ti.com>
FSG_NUM_BUFFERS is set to 2 as default.
Usually 2 buffers are enough to establish a good buffering pipeline.
The number may be increased in order to compensate a for bursty VFS
behaviour.
Here follows a description of system that may require more than
2 buffers.
* CPU ondemand governor active
* latency cost for wake up and/or frequency change
* DMA for IO
Use case description.
* Data transfer from MMC via VFS to USB.
* DMA shuffles data from MMC and to USB.
* The CPU wakes up every now and then to pass data in and out from VFS,
which cause the bursty VFS behaviour.
Test set up
* Running dd on the host reading from the mass storage device
* cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100))
* Caches are dropped on the host and on the device before each run
Measurements on a Snowball board with ondemand_governor active.
FSG_NUM_BUFFERS 2
104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s
FSG_NUM_BUFFERS 4
104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s
There may not be one optimal number for all boards. This is why
the number is added to Kconfig. If selecting USB_GADGET_DEBUG_FILES
this value may be set by a module parameter as well.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1481) fixes a problem affecting g_file_storage and
g_mass_storage when running at SuperSpeed. The two drivers currently
assume that the bulk-out maxpacket size can evenly divide the SCSI
block size, which is 512 bytes. But SuperSpeed bulk endpoints have a
maxpacket size of 1024, so the assumption is no longer true.
This patch removes that assumption from the drivers, by getting rid of
a small optimization (they try to align VFS reads and writes on page
cache boundaries). If a command's starting logical block address is
512 bytes below the end of a page, it's not okay to issue a USB
command for just those 512 bytes when the maxpacket size is 1024 -- it
would result in either babble (for an OUT transfer) or a short packet
(for an IN transfer).
Also, for backward compatibility, the test for writes extending beyond
the end of the backing storage has to be changed. If the host tries
to do this, we should accept the data that fits in the backing storage
and ignore the rest. Because the storage's end may not align with a
USB packet boundary, this means we may have to accept a USB OUT
transfer that extends beyond the end of the storage and then write out
only the part of the data that fits.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now the mass storage driver has fixed logic block size of 512 bytes.
The mass storage gadget read/write bound devices only through VFS, so the
bottom level devices actually are just RAW devices to the driver and connected
PC. As a RAW, hosts can always format, read and write it right in 512 bytes
logic block and don't care about the actual logic block size of devices bound
to the gadget.
But if we want to share the bound block device partition between target board
and PC, in case the logic block size of the bound block device is 4KB, we
execute the following steps:
1. connect a board with mass storage gadget to PC(the board has set one
partition of on-board block device as file name of the mass storage)
2. PC format the mass storage to VFAT by default logic block size and
read/write it
3. disconnect boards from PC
4. target board mount the partition as VFAT
Step 4 will fail since kernel on target thinks the logic block size of the
bound partition as 4KB.
A typical error is "FAT: logical sector size too small for device (logical
sector size = 512)"
If we execute opposite steps:
1. format the partition to VFAT on target board and read/write this partition
2. connect the board to Windows PC as usb mass storage gadget, windows will
think the disk is not formatted
So the conclusion is that only as a gadget, the mass storage driver has no any
problem. But being shared VFAT or other filesystem on PC and target board, it
will fail.
This patch adapts logic block size to bound block devices and fix the issue.
Cc: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peiyu Li <peiyu.li@csr.com>
Signed-off-by: Xianglong Du <xianglong.du@csr.com>
Signed-off-by: Huayi Li <huayi.li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's useful to know which states core is going
through, as it might help us figure out misbehavior
on specific link states.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag will tell us which direction we're
expecting on the next (data or status) phase.
It will help us catching errors of host going
crazy and requesting data of the wrong direction.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if req->dma isn't DMA_ADDR_INVALID it means gadget driver
mapped the request or allocated from coherent, so it's
unnecessary to do anything.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the gadget drivers sends a ZLP we are trying to map this this request
which does not work on all implementations. So we simply skip mapping
it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3-wrapper can be used by any other wrapper,
using dwc3-omap makes it clear that we're running
on OMAP SoC.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The OMAP wrapper allows us to either control internal
OTG signals via SW or HW. Different boards might wish
to use one or the other mode of operation. Let's have
have that information passed via platform_data for now.
After DT conversion is finished for OMAP, we can easily
convert this to a DT attribute.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to have actual HW in order to implement
and test that part of the code anyway. Until then
it's best to remove it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this field will hold the next expected event.
In certain cases, host might fall into some error
condition and ask from us the wrong Control phase.
On such situations, we should stall and restart.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever we issue a Set Stall command on EP0,
the state machine will be restarted and Stall
is cleared automatically, when core receives
the next SETUP packet.
There's no need to track that EP0_STALL state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when we're going to issue Set Stall command,
we should clear DWC3_EP_STALL flag, but also
we should clear BUSY, HALTED and all others.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are two spots where we wait until the HW finishes processing a
certain command. Initially we had a few problems and we used 500ms as a
limit to be on a the safe side. Paul Zimmerman mentioned this is little too
much. After a debugging session, we noticed that we hardly ever go over 20us
and didn't pass 30usec so far. Using mdelay() seems way overloaded.
Giving the current numbers 500usec as the upper limit is more than enough.
Should it ever timeout then something is definitely wrong.
While here, also replace the type with u32 since long does not really
fit here.
Cc: Paul Zimmerman <paul.zimmerman@synopsys.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- since a while we are disabling an endpoint and purging every requests on
RESET and DISCONNECT which leads to a warning since the endpoint was
disabled twice (once by the UDC, and second time by the gadget). I
think UDC should nuke all requests because all those requests
become invalid. It's gadget driver's responsability, though, to disable
its used endpoints. This is done by merging dwc3_stop_active_transfer()
and dwc3_gadget_nuke_reqs() into dwc3_remove_requests().
- dwc3_stop_active_transfer() is now no longer called unconditionaly.
This has the advantage that it is always called to disable an active
transfer which means if res_trans_idx 0 than something went wrong and
it is an error condition because we can't clean up the requests.
- Remove the DWC3_EP_WILL_SHUTDOWN which was introduced while
introducing the command complete part for dequeue. All requests on
req_queued list should be removed during the dwc3_cleanup_done_reqs()
callback so there is no reason to go through the list again.
We consider it an error condition if requests are still on this
list since we never queue TRB without LST=1 (the last requests has
always LST=1, there are no requests with LST=0 behind it).
[ balbi@ti.com : reworked commit log a bit, made patch apply ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We read the DWC3_GSNPSID register to make sure we got the correct
register offset passed. One of the recent commits moved the soft reset
before this so in case of the wrong offset we end up with "reset timed
out". This patch moves the "id" check before the reset again.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some issues around for enabling/disabling this mode and
handling it. It does not work perfectly (yet). However we have a few
gadgets tested successfuly so far. That means we are quite confident
that we won't need this in near future.
So I'm for removing it and bringing a working version back once there is
a need for it.
Thanks to Dan Carpenter who spotted the wrong memory handling here.
[ balbi@ti.com : made it actually apply ]
Cc: Dan Carpenter <error27@gmail.com>
Cc: wharms@bfs.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The DesignWare USB3 core tells us which phase
of a control transfer should be started, it
also tells us which physical endpoint needs
that transfer.
With these two informations, we have all we
need to simply EP0 handling quite a lot and
get rid rid of the SW state machine tracking
ep0 states.
For achieving this perfectly, we needed to
add support for situations where we get
XferNotReady while endpoint is still busy
and XferNotReady while gadget driver still
hasn't queued a request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we have transfers which aren't aligned
to wMaxPacketSize, we need to be careful with
how we start the transfer with the HW. OUT
transfers _must_ be aligned with wMaxPacketSize
and in order to guarantee that, we use a bounce
buffer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This core cannot handle OUT transfers which aren't
aligned to wMaxPacketSize, but that can happen at
least on control endpoint with the USB Audio Class.
This patch adds a bounce buffer to be used on the
case of a non-aligned ep0out request is queued.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The status field of the Transfer Not Read event
is different on Control Endpoints. On this patch
we are just adding the defines to be used on a
later patch which will re-work the control endpoint
handling.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the previous message had too little meaning. Make
it more human readable and use the macro we already
had for extracting the command completion status out
of DEPCMDn register.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we don't set DMA address to invalid when unmapping,
we might fall in a situation where request buffer
can't be mapped to DMA again.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We may as well fix this potential leak so we don't have to listen to
the static checkers complain.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this patch we won't clear that bit and instead will
clear all other bits on our endpoint flag.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Type 6 should be used for the first transfer during an interval. This is
also what the reference driver is using. Type 7 seems to be for following
or additional transfers within the same interval.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we collected two requests together (i.e. only the last of them has
LST=1) then we only have to stop transfer once: The clean-up code will
cleanup everything until first TRB with the LST bit set.
After XferComplete this index should be no longer valid since there is
no transfer pending.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A TRB which is dequeued seems to have its HWO bits set to 1. Therefore
we ignore it if we dequeue it after the command is completed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Calao use on there dev kits a FT2232 where the port 0 is used for the JTAG and
port 1 for the UART
They use the same VID and PID as FTDI Chip but they program the manufacturer
name in the eeprom
So use this information to detect it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes rts51x_read_mem, rts51x_write_mem, and rts51x_read_status to
allocate temporary buffers with kmalloc. This way stack addresses are not used
for DMA when these functions call rts51x_bulk_transport.
Signed-off-by: Adam Cozzette <acozzette@cs.hmc.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the MACH_MX* macros are scheduled for removal, so just depend
on ARCH_MXC instead. The Kconfig text makes it clear on which
SoC the driver runs on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ARCH_MX1 scheduled for removal. Instead, depend on ARCH_MXC
and make clear in the Kconfig text that only i.MX1 has this
hardware.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error when CONFIG_USB_GADGET_DWC3 is not enabled:
ERROR: "dwc3_send_gadget_ep_cmd" [drivers/usb/dwc3/dwc3.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up
Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes this build error:
drivers/usb/dwc3/dwc3-pci.c: In function 'dwc3_pci_init':
drivers/usb/dwc3/dwc3-pci.c:211:9: error: 'THIS_MODULE' undeclared (first use in this function)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Executing
| testusb -a -c 1 -t 3 -v 421 -s 2048
does not complete on the gadget side.
g_zero enqueues a 4096 bytes long buffer. The host sends 2048bytes which
is a multiple of wMaxPacketSize (either 64 or 512 bytes). The host is
done with sending data but the gadget waits for more.
Since the protocol does not include transfer-length-field sending a
terminating zero packet seems the only way out.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MPC832x does not have enough MURAM to do fixed MURAM allocation.
Change to dynamic allocation.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a low or full speed urb in progress is unlinked (or some other error
occurs), the buffer in the transaction translator (part of the hub) might end
up in an inconsistent state. This can make all further low and full speed
transactions fail, unless the buffer is cleared.
The bug can be seen when running the usbtest unlink tests as "set altsetting
to 0 failed, -110", and gets fixed by this patch.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Test the just-initialized value rather than some other one.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier x,y,f!={PTR_ERR,ERR_PTR,ERR_CAST};
statement S;
@@
x = f(...);
(
if (\(x == NULL\|IS_ERR(x)\)) S
|
*if (\(y == NULL\|IS_ERR(y)\))
{ ... when != x
return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unused function twl6030_set_phy_clk of twl6030-usb.c.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes it possible to use i.e. gpio-vbus to handle vbus events.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-interrupt is requested before the endpoints are initalised.
If an interrupt happens in the time between request_irq and the init
of the endpoint-data (as seen on the Qisda ESx00 ebook-platforms),
it is therefore possible for the interrupt handler to access endpoint-
data before its creation resulting in a null-pointer dereference.
This patch simply moves the irq request below the endpoint init.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.
Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.
The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.
More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.
While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.
[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable. It has no clear owner and
it isn't protected by the usual HCD locks. In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.
Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable. Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add supprt for on-chip USB controller for Netlogic XLS MIPS64
SoC processor family.
Changes are:
- update ehci-hcd.c and ohci-hcd.c to add XLS hcds
- add ehci-xls.c: EHCI support for Netlogic XLS.
- add ohci-xls.c: OHCI support for Netlogic XLS.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These messages just clutter the log and provide no useful information to
the user, so make them pr_debug().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1) A bug in the usage of time_after() in errata2_function().
2) Clear done_maps just prior to starting a new transfer in
start_bus_transfer(), instead of just after, when done_map bits might have
been validly set by the started transfer.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and some small code style fixes.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Errata 2 for the isp1760 explains that the chip sometimes does not issue
interrupts when an ATL (bulk or control) transfer is completed. There are
several issues with the current work-around (SOF interrupts) for this:
1) It seems the chip sometimes does not even set the done bit for a
completed transfer, in which case SOF interrupts does not solve
the problem since we still check the done map to find out which
transfer descriptors to handle.
2) The above point seems to happen only when ATL and SOF interrupts
are enabled at the same time. However, disabling ATL interrupts
increases the latency between transfer completion and handling.
This is very noticeable in the testusb suite, which take several
minutes more to run with ATL interrupts disabled.
This patch removes the code to switch on SOF interrupts, and instead
use a kernel timer to periodically check for "old" descriptors that
have their VALID and ACTIVE flags unset, indicating completion, thus
avoiding the dependency on the chip's done map (and SOF interrupts)
to find transfers affected by this HW bug.
[bigeasy@linutronix: 80 lines limit]
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like the previous patch, this patch has been split from the next one
for clarity.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the few lines of code in isp1760_enable_interrupts() and
isp1760_init_maps() into isp1760_run(). This makes the following patch
easier.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From 2d487c10136f76cf3705881d34868e8592839cfe Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Tue, 12 Jul 2011 15:36:51 +0200
Subject: [PATCH] USB: ipw: convert to usb-wwan framework
This patch allows the ipw driver to use the multibuffer
infrastructure of usb-wwan. This improves speed.
Signed-off-by: Oliver Neukum<oneukum@suse.de>
Tested-by: Michal Hybner <dta081@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Scanning cannot be run during suspend or hibernation, but if
usb-stor-scan freezes another thread waiting on scanning to
complete may fail to freeze.
However, if usb-stor-scan is left freezable without ever actually
freezing then the freezer will wait on it to exit, and threads
waiting for scanning to finish will no longer be blocked. One
problem with this approach is that usb-stor-scan has a delay to
wait for devices to settle (which is currently the only point where
it can freeze). To work around this we can request that the freezer
send a fake signal when freezing, then use interruptible sleep to
wake the thread early when freezing happens.
To make this happen, the following changes are made to
usb-stor-scan:
* Use set_freezable_with_signal() instead of set_freezable() to
request a fake signal when freezing
* Use wait_event_interruptible_timeout() instead of
wait_event_freezable_timeout() to avoid freezing
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/usb/core/hub.c::usb_disconnect(), 'udev' will never be
NULL, so remove the test and printing of debug message.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the Option driver avoids binding interface 1 on Huawei K3765
and K4505 broadband modems as it should be handled by the cdc_ether
driver instead. This patch ensures we don't bind the interface 2
on those devices as that is CDC_DATA.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a NULL pointer deference. A NULL pointer
dereference happens since s5p_ehci->hcd field is not initialized
yet in probe function.
[jg1.han@samsung.com: edit commit message]
Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.
Signed-off-by: Wang Zhi <zhi.wang@windriver.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by suitable network
driver.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
xhci: Remove TDs from TD lists when URBs are canceled.
xhci: Fix failed enqueue in the middle of isoch TD.
xhci: Fix memory leak during failed enqueue.
xHCI: report USB2 port in resuming as suspend
xHCI: fix port U3 status check condition
For a long time, the xHCI driver has had this note:
/* FIXME: Ignoring zero-length packets, can those happen? */
It turns out that, yes, there are drivers that need to queue zero-length
transfers for isochronous OUT transfers. Without this patch, users will
see kernel hang messages when a driver attempts to enqueue an isochronous
URB with a zero length transfer (because count_isoc_trbs_needed will return
zero for that TD, xhci_td->last_trb will never be set, and updating the
dequeue pointer will cause an infinite loop).
Matěj ran into this issue when using an NI Audio4DJ USB soundcard
with the snd-usb-caiaq driver. See
https://bugzilla.kernel.org/show_bug.cgi?id=40702
Fix count_isoc_trbs_needed() to return 1 for zero-length transfers (thanks
Alan on the math help). Update the various TRB field calculations to deal
with zero-length transfers. We're still transferring one packet with a
zero-length data payload, so the total_packet_count should be 1. The
Transfer Burst Count (TBC) and Transfer Last Burst Packet Count (TLBPC)
fields should be set to zero.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Matěj Laitl <matej@laitl.cz>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
usb_ifnum_to_if() can return NULL if the USB device does not have a
configuration installed (usb_device->actconfig == NULL), or if we can't
find the interface number in the installed configuration. Return an
error instead of crashing.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
In case one "forgot" to load the receiver i.e. doing
|modprobe omap2430
|modprobe musb_hdrc
he ends up with:
|musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
|HS USB OTG: no transceiver configured
|musb-hdrc musb-hdrc: musb_init_controller failed with status -19
|(NULL device *): gadget not registered.
|Unable to handle kernel NULL pointer dereference at virtual address 0000001c
|Internal error: Oops: 17 [#1] SMP
|[<c011383c>] (sysfs_find_dirent+0x4/0x60) from [<c01138c0>] (sysfs_get_dirent+0x28/0x78)
|[<c01138c0>] (sysfs_get_dirent+0x28/0x78) from [<c0115b78>] (sysfs_unmerge_group+0x1c/0x90)
|[<c0115b78>] (sysfs_unmerge_group+0x1c/0x90) from [<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c)
|[<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c) from [<c01742f8>] (device_del+0x40/0x1b4)
|[<c01742f8>] (device_del+0x40/0x1b4) from [<c0174478>] (device_unregister+0xc/0x18)
|[<c0174478>] (device_unregister+0xc/0x18) from [<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc])
|[<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc]) from [<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc])
|[<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc]) from [<c01779c4>] (platform_drv_probe+0x1c/0x24)
The problem is that musb_free() tries to figure out what was
initializued and what wasn't and clean up only the initialized part.
This works well for usb_del_gadget_udc() but device_unregister() can't
deal with it. Therefore we rely on the fact the we always have a parent
device and only then remove the device.
I broke this in 0f91349 ("usb: gadget: convert all users to the new udc
infrastructure")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the prefetch/list.h restructure, drivers need to explicitly include
linux/prefetch.h in order to use the prefetch() function. Otherwise, the
current driver fails to build:
drivers/usb/musb/blackfin.c: In function 'musb_write_fifo':
drivers/usb/musb/blackfin.c:43: error: implicit declaration of function
'prefetch'
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Include dma-mapping.h to fix build of the renesas_usbhs driver
| CC drivers/usb/renesas_usbhs/mod_gadget.o
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_map':
| drivers/usb/renesas_usbhs/mod_gadget.c:190: error: implicit declaration of function 'dma_map_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:192: error: implicit declaration of function 'dma_sync_single_for_device'
| drivers/usb/renesas_usbhs/mod_gadget.c:196: error: implicit declaration of function 'dma_mapping_error'
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_unmap':
| drivers/usb/renesas_usbhs/mod_gadget.c:217: error: implicit declaration of function 'dma_unmap_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:219: error: implicit declaration of function 'dma_sync_single_for_cpu'
| make[5]: *** [drivers/usb/renesas_usbhs/mod_gadget.o] Error 1
| make[4]: *** [drivers/usb/renesas_usbhs] Error 2
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace DBG with dev_dbg and fix invalid access of musb->controller.
With this patch cppi_dma builds successfully.
Cc: <stable@kernel.org>
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ux500_dma.c fail to compile becase DBG has been removed from musb_debug.
Use dev_dbg for all prints.
Cc: stable@vger.kernel.org
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab<mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dma driver requires both src and dst to be set.
This fix is needed in order to run gadget mass storage.
Patch is verified on snowball.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Cc: stable@kernel.org
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Obviously, disabling & put regulator and iounmap(hcd->regs)
are missed in .remove and failure handling path of .probe,
so add them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Keshava Munegowda <Keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CC drivers/usb/musb/tusb6010_omap.o
drivers/usb/musb/tusb6010_omap.c: In function 'tusb_omap_use_shared_dmareq':
drivers/usb/musb/tusb6010_omap.c:92: error: 'musb' undeclared (first use in this function)
drivers/usb/musb/tusb6010_omap.c:92: error: (Each undeclared identifier is reported only once
drivers/usb/musb/tusb6010_omap.c:92: error: for each function it appears in.)
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here is a patch for a new PID (zeitcontrol-device mifare-reader FT232BL(like FT232BM but lead free)).
Signed-off-by: Artur Zimmer <artur128@3dzimmer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A new device ID pair is added for Sierra Wireless MC8305.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver tries to cancel an URB, and the host controller is dying,
xhci_urb_dequeue will giveback the URB without removing the xhci_tds
that comprise that URB from the td_list or the cancelled_td_list. This
can cause a race condition between the driver calling URB dequeue and
the stop endpoint command watchdog timer.
If the timer fires on a dying host, and a driver attempts to resubmit
while the watchdog timer has dropped the xhci->lock to giveback a
cancelled URB, URBs may be given back by the xhci_urb_dequeue() function.
At that point, the URB's priv pointer will be freed and set to NULL, but
the TDs will remain on the td_list. This will cause an oops in
xhci_giveback_urb_in_irq() when the watchdog timer attempts to loop
through the endpoints' td_lists, giving back killed URBs.
Make sure that xhci_urb_dequeue() removes TDs from the TD lists and
canceled TD lists before it gives back the URB.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When an isochronous transfer is enqueued, xhci_queue_isoc_tx_prepare()
will ensure that there is enough room on the transfer rings for all of the
isochronous TDs for that URB. However, when xhci_queue_isoc_tx() is
enqueueing individual isoc TDs, the prepare_transfer() function can fail
if the endpoint state has changed to disabled, error, or some other
unknown state.
With the current code, if Nth TD (not the first TD) fails, the ring is
left in a sorry state. The partially enqueued TDs are left on the ring,
and the first TRB of the TD is not given back to the hardware. The
enqueue pointer is left on the TRB after the last successfully enqueued
TD. This means the ring is basically useless. Any new transfers will be
enqueued after the failed TDs, which the hardware will never read because
the cycle bit indicates it does not own them. The ring will fill up with
untransferred TDs, and the endpoint will be basically unusable.
The untransferred TDs will also remain on the TD list. Since the td_list
is a FIFO, this basically means the ring handler will be waiting on TDs
that will never be completed (or worse, dereference memory that doesn't
exist any more).
Change the code to clean up the isochronous ring after a failed transfer.
If the first TD failed, simply return and allow the xhci_urb_enqueue
function to free the urb_priv. If the Nth TD failed, first remove the TDs
from the td_list. Then convert the TRBs that were enqueued into No-op
TRBs. Make sure to flip the cycle bit on all enqueued TRBs (including any
link TRBs in the middle or between TDs), but leave the cycle bit of the
first TRB (which will show software-owned) intact. Then move the ring
enqueue pointer back to the first TRB and make sure to change the
xhci_ring's cycle state to what is appropriate for that ring segment.
This ensures that the No-op TRBs will be overwritten by subsequent TDs,
and the hardware will not start executing random TRBs because the cycle
bit was left as hardware-owned.
This bug is unlikely to be hit, but it was something I noticed while
tracking down the watchdog timer issue. I verified that the fix works by
injecting some errors on the 250th isochronous URB queued, although I
could not verify that the ring is in the correct state because uvcvideo
refused to talk to the device after the first usb_submit_urb() failed.
Ring debugging shows that the ring looks correct, however.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When the isochronous transfer support was introduced, and the xHCI driver
switched to using urb->hcpriv to store an "urb_priv" pointer, a couple of
memory leaks were introduced into the URB enqueue function in its error
handling paths.
xhci_urb_enqueue allocates urb_priv, but it doesn't free it if changing
the control endpoint's max packet size fails or the bulk endpoint is in
the middle of allocating or deallocating streams.
xhci_urb_enqueue also doesn't free urb_priv if any of the four endpoint
types' enqueue functions fail. Instead, it expects those functions to
free urb_priv if an error occurs. However, the bulk, control, and
interrupt enqueue functions do not free urb_priv if the endpoint ring is
NULL. It will, however, get freed if prepare_transfer() fails in those
enqueue functions.
Several of the error paths in the isochronous endpoint enqueue function
also fail to free it. xhci_queue_isoc_tx_prepare() doesn't free urb_priv
if prepare_ring() indicates there is not enough room for all the
isochronous TDs in this URB. If individual isochronous TDs fail to be
queued (perhaps due to an endpoint state change), urb_priv is also leaked.
This argues that the freeing of urb_priv should be done in the function
that allocated it, xhci_urb_enqueue.
This patch looks rather ugly, but refactoring the code will have to wait
because this patch needs to be backported to stable kernels.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When a USB2 port initiate a remote wakeup, software shall ensure that
resume is signaled for at least 20ms, and then write '0' to the PLS field.
According to this, xhci driver do the following things:
1. When receive a remote wakeup event in irq_handler, set the resume_done
value as jiffies + 20ms, and modify rh_timer to poll root hub status at
that time;
2. When receive a GetPortStatus request, if the jiffies is after the
resume_done value, clear the resume signal and resume_done.
However, if usb_port_resume() is called before the rh_timer triggered, it
will indicate the port as Suspend Cleared and skip the clear resume signal
part. The device will fail the usb_get_status request in finish_port_resume(),
and usbcore will try a reset-resume instead. Device will work OK after
reset-resume, but resume_done value is not cleared in this case, and
xhci_bus_suspend() will fail because when it finds a non-zero resume_done
value, it will regard the port as resuming and return -EBUSY.
This causes issue on some platforms that the system fail to suspend
after remote wakeup from suspend by USB2 devices connected to xHCI port.
To fix this issue, report the port status as suspend if the resume is
signaling less that 20ms, and usb_port_resume() will wait 25ms and check
port status again, so xHCI driver can clear the resume signaling and
resume_done value.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Fix the port U3 status check when Clear PORT_SUSPEND Feature.
The port status should be masked with PORT_PLS_MASK to check if it's in
U3 state.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
A new device ID pair is added for Qualcomm Modem present in Sagemcom's HiLo3G module.
Signed-off-by: Vijay Chavan <VijayChavan007@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci_bios_handoff() is marked __devinit, `ehci_dmi_nohandoff_table' should be
marked __devinitconst, not __initconst. This fixes the following section
mismatch:
WARNING: vmlinux.o(.devinit.text+0x4f08): Section mismatch in reference from the function ehci_bios_handoff() to the variable .init.rodata:ehci_dmi_nohandoff_table
The function __devinit ehci_bios_handoff() references a variable __initconst ehci_dmi_nohandoff_table.
If ehci_dmi_nohandoff_table is only used by ehci_bios_handoff then annotate ehci_dmi_nohandoff_table with a matching annotation.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4511 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4510 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3771 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3770 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the recent addition of the FT232H showed that baudrate was set wrong. See
gmane.linux.usb.general: "[ftdi_sio] FT232H support". With the old code,
the MSB of the 4 encoded fractional divider bits and more important the
clock predivider bits got lost. Adding the FT232H to the code patch were
these bits are shifted solves the problem. I verified baud rates with a
scope now.
I suspect, that the BM device probably needs these bits shifted too. But
there is no predivider bit, so this is not obvious, and a missing MSB of the
encoded fractional divider only shifts the resulting baudrate minimal.
The AM has only 3 bits of encoded fractional divider, so it is not impacted.
I have no BM device to test, so I only added a comment and left the code for
the BM untouched.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sequence to put port in test mode is not complete.
According EHCI specification all enabled ports must be
put in suspend.
Signed-off-by: Boris Todorov <boris.st.todorov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Even if it's unlikely for this to cause an error,
there is a typo in the code that uses the bitwise-AND
operator instead of the logical one.
Signed-off-by: Ionut Nicu <ionut.nicu@cloudbit.ro>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Connecting the V2M to a Linux host results in a constant stream of
errors spammed to the console, all of the form
sd 1:0:0:0: ioctl_internal_command return code = 8070000
: Sense Key : 0x4 [current]
: ASC=0x0 ASCQ=0x0
The errors appear to be otherwise harmless. Add an unusual_devs entry
which eliminates all of the error messages.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As cpu_is_mx stuff is being used in the driver, header mach/hardware.h
should be explicitly included.
The missing of the header is causing today's linux-next build error
as bleow.
CC drivers/usb/host/ehci-hcd.o
In file included from linux-next/drivers/usb/host/ehci-hcd.c:1190:0:
linux-next/drivers/usb/host/ehci-mxc.c: In function 'ehci_mxc_drv_probe':
linux-next/drivers/usb/host/ehci-mxc.c:175:2: error: implicit declaration of function 'cpu_is_mx35'
linux-next/drivers/usb/host/ehci-mxc.c:175:2: error: implicit declaration of function 'cpu_is_mx25'
linux-next/drivers/usb/host/ehci-mxc.c:185:2: error: implicit declaration of function 'cpu_is_mx51'
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Assign operator instead of equality test in the usbtmc_ioctl_abort_bulk_in() function.
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1st pos of __usbhsg_for_each_uep() was wrong.
Expected uep were ep1, ep2, ep3...
but each uep were ep0, ep2, ep3 ...
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Include dma-mapping.h to fix build of the renesas_usbhs driver
CC drivers/usb/renesas_usbhs/mod_gadget.o
drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_map':
drivers/usb/renesas_usbhs/mod_gadget.c:190: error: implicit declaration of function 'dma_map_single'
drivers/usb/renesas_usbhs/mod_gadget.c:192: error: implicit declaration of function 'dma_sync_single_for_device'
drivers/usb/renesas_usbhs/mod_gadget.c:196: error: implicit declaration of function 'dma_mapping_error'
drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_unmap':
drivers/usb/renesas_usbhs/mod_gadget.c:217: error: implicit declaration of function 'dma_unmap_single'
drivers/usb/renesas_usbhs/mod_gadget.c:219: error: implicit declaration of function 'dma_sync_single_for_cpu'
make[5]: *** [drivers/usb/renesas_usbhs/mod_gadget.o] Error 1
make[4]: *** [drivers/usb/renesas_usbhs] Error 2
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
<linux/irq.h> states:
* Please do not include this file in generic code. There is currently
* no requirement for any architecture to implement anything held
* within this file.
prefetch() and prefetchw() need <linux/prefetch.h> on m68k:
drivers/usb/gadget/net2272.c: In function ‘net2272_write_fifo’:
drivers/usb/gadget/net2272.c:468: error: implicit declaration of function ‘prefetch’
drivers/usb/gadget/net2272.c: In function ‘net2272_read_fifo’:
drivers/usb/gadget/net2272.c:574: error: implicit declaration of function ‘prefetchw’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
usb/config: use proper endian access for wMaxPacketSize
USB: xhci: fix OS want to own HC
xhci: Don't submit commands or URBs to halted hosts.
an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Cc: stable@kernel.org
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Obviously, disabling & put regulator and iounmap(hcd->regs)
are missed in .remove and failure handling path of .probe,
so add them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Keshava Munegowda <Keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CC drivers/usb/musb/tusb6010_omap.o
drivers/usb/musb/tusb6010_omap.c: In function 'tusb_omap_use_shared_dmareq':
drivers/usb/musb/tusb6010_omap.c:92: error: 'musb' undeclared (first use in this function)
drivers/usb/musb/tusb6010_omap.c:92: error: (Each undeclared identifier is reported only once
drivers/usb/musb/tusb6010_omap.c:92: error: for each function it appears in.)
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
wMaxPacketSize is __le16 and should be accessed as such. Also fix the
wBytesPerInterval assignment while here.
v2: also fix the wBytesPerInterval assigment, noticed by Matt Evans
This patch should be backported to the 3.0 kernel.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Matt Evans <matt@ozlabs.org>
Cc: stable@kernel.org
Software should set XHCI_HC_OS_OWNED bit to request ownership of xHC.
This patch should be backported to kernels as far back as 2.6.31.
Signed-off-by: JiSheng Zhang <jszhang3@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Commit fccf4e8620
"USB: Free bandwidth when usb_disable_device is called" caused a bit of an
issue when the xHCI host controller driver is unloaded. It changed the
USB core to remove all endpoints when a USB device is disabled. When the
driver is unloaded, it will remove the SuperSpeed split root hub, which
will disable all devices under that roothub and then halt the host
controller. When the second High Speed split roothub is removed, the USB
core will attempt to disable the endpoints, which will submit a Configure
Endpoint command to a halted host controller.
The command will eventually time out, but it makes the xHCI driver unload
take *minutes* if there are a couple of USB 1.1/2.0 devices attached. We
must halt the host controller when the SuperSpeed roothub is removed,
because we can't allow any interrupts from things like port status
changes.
Make several different functions not submit commands or URBs to the host
controller when the host is halted, by adding a check in
xhci_check_args(). xhci_check_args() is used by these functions:
xhci.c-int xhci_urb_enqueue()
xhci.c-int xhci_drop_endpoint()
xhci.c-int xhci_add_endpoint()
xhci.c-int xhci_check_bandwidth()
xhci.c-void xhci_reset_bandwidth()
xhci.c-static int xhci_check_streams_endpoint()
xhci.c-int xhci_discover_or_reset_device()
It's also used by xhci_free_dev(). However, we have to take special
care in that case, because we want the device memory to be freed if the
host controller is halted.
This patch should be backported to the 2.6.39 and 3.0 kernel.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
The driver had to decide how many events to allocate when the v4l2_fh struct
was created. It was possible to add more events afterwards, but there was no
way to ensure that you wouldn't miss important events if the event queue
would fill up for that filehandle.
In addition, once there were no more free events, any new events were simply
dropped on the floor.
For the control event in particular this made life very difficult since
control status/value changes could just be missed if the number of allocated
events and the speed at which the application read events was too low to keep
up with the number of generated events. The application would have no idea
what the latest state was for a control since it could have missed the latest
control change.
So this patch makes some major changes in how events are allocated. Instead
of allocating events per-filehandle they are now allocated when subscribing an
event. So for that particular event type N events (determined by the driver)
are allocated. Those events are reserved for that particular event type.
This ensures that you will not miss events for a particular type altogether.
In addition, if there are N events in use and a new event is raised, then
the oldest event is dropped and the new one is added. So the latest event
is always available.
This can be further improved by adding the ability to merge the state of
two events together, ensuring that no data is lost at all. This will be
added in the next patch.
This also makes it possible to allow the user to determine the number of
events that will be allocated. This is not implemented at the moment, but
would be trivial.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that supported events used to be rare, but now that controls can also
raise events this will become much more common since almost all drivers have
controls.
This means that keeping struct v4l2_events as a separate struct make no more
sense. Merging it into struct v4l2_fh simplifies things substantially as it
is now an integral part of the filehandle struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sarah Sharp