Currently, the frequency that devfreq provides the driver always leads the
clocks to be scaled up. Hence, round the clock-rate to the nearest
frequency before deciding to scale.
Also update the devfreq statistics of current frequency.
Link: https://lore.kernel.org/r/d0c6c22455811e9f0eda01f9bc70d1398b51b2bd.1585160616.git.asutoshd@codeaurora.org
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As a part of sysfs reading of descriptors/attributes/flags, query commands
should only be executed when hba's power runtime status is active. To
guarantee this, add pm_runtime_get/put_sync() to those paths where query
commands are sent.
Link: https://lore.kernel.org/r/f712a4f7bdb0ae32e0d83634731e7aaa1b3a6cdd.1585009663.git.asutoshd@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Nitin Rawat <nitirawa@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MediaTek platform and UFS controller can dynamically customize the delay
for host enabling according to different scenarios.
For example, if UniPro enters lower-power mode, such delay can be
minimized, otherwise longer delay shall be expected.
Link: https://lore.kernel.org/r/20200318104016.28049-8-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the waiting period between each HCE (Host Controller Enable) polling
from 5 ms to 1 ms. Also increase the maximum polling times to make "total
polling time" roughly the same.
This change could make HCE initialization faster to improve latency of
ufshcd initialization, error recovery, and resume behaviors.
Link: https://lore.kernel.org/r/20200318104016.28049-7-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a 1 ms delay is applied before polling CONTROLLER_ENABLE
bit. This delay may not be required or can be changed in different
controllers. Make the delay as a changeable value in struct ufs_hba to
allow it customized by vendors.
Link: https://lore.kernel.org/r/20200318104016.28049-6-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A common delay function is introduced in UFS core driver, thus ufs-mediatek
can use it instead of the private delay function.
Link: https://lore.kernel.org/r/20200318104016.28049-5-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a common delay function to provide flexible way for users to take
choices of udelay and usleep_range into consideration according to the
required delay time.
Link: https://lore.kernel.org/r/20200318104016.28049-4-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use an enum to specify the host capabilities instead of #defines inside the
structure definition.
Link: https://lore.kernel.org/r/20200318104016.28049-3-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufshcd_disable_tx_lcc(), if ufshcd_dme_get() or ufshcd_dme_peer_get()
get fail, uninitialized variable "tx_lanes" may be used as unexpected lane
ID for DME configuration.
Fix this issue by initializing "tx_lanes".
Link: https://lore.kernel.org/r/20200318104016.28049-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an iSCSI connection happens to fail while the daemon isn't running (due
to a crash or for another reason), the kernel failure report is not
received. When the daemon restarts, there is insufficient kernel state in
sysfs for it to know that this happened. open-iscsi tries to reopen every
connection, but on different initiators, we'd like to know which
connections have failed.
There is session->state, but that has a different lifetime than an iSCSI
connection, so it doesn't directly reflect the connection state.
[mkp: typos]
Link: https://lore.kernel.org/r/20200317233422.532961-1-krisman@collabora.com
Cc: Khazhismel Kumykov <khazhy@google.com>
Suggested-by: Junho Ryu <jayr@google.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If 'dma_map_single()' fails, the ref counted 'shpnt' will be decremented
twice because 'scsi_host_put()' is called in the if block, and in the error
handling path.
Axe one of these calls.
Link: https://lore.kernel.org/r/20200228215948.7473-1-christophe.jaillet@wanadoo.fr
Fixes: 1dc09e120c ("scsi: aha1740: stop using scsi_unregister")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove code which has no functional use anymore since commit 3c75ad1d87
("scsi: qla2xxx: Remove defer flag to indicate immeadiate port loss").
While at it remove also the stale function documentation.
Link: https://lore.kernel.org/r/20200206135443.110701-1-dwagner@suse.de
Reviewed-by: Arun Easi <aeasi@marvell.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no reason to expose SATA_PMP config option when no SATA
host drivers are enabled. To fix it add SATA_HOST config option,
make all SATA host drivers select it and finally make SATA_PMP
config options depend on it.
This also serves as preparation for the future changes which
optimize libata core code size on PATA only setups.
CC: "James E.J. Bottomley" <jejb@linux.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # for SCSI bits
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some USB bridge devices will return a default set of characteristics during
initialization. And then, once an attached drive has spun up, substitute
the actual parameters reported by the drive. According to the SCSI spec,
the device should return a UNIT ATTENTION in case any reported parameters
change. But in this case the change is made silently after a small window
where default values are reported.
Commit a83da8a450 ("scsi: sd: Optimal I/O size should be a multiple of
physical block size") validated the reported optimal I/O size against the
physical block size to overcome problems with devices reporting nonsensical
transfer sizes. However, this validation did not account for the fact that
aforementioned devices will return default values during a brief window
during spin-up. The subsequent change in reported characteristics would
invalidate the checking that had previously been performed.
Unset a previously configured optimal I/O size should the sanity checking
fail on subsequent revalidate attempts.
Link: https://lore.kernel.org/r/33fb522e-4f61-1b76-914f-c9e6a3553c9b@gmail.com
Cc: Bryan Gurney <bgurney@redhat.com>
Cc: <stable@vger.kernel.org>
Reported-by: Bernhard Sulzer <micraft.b@gmail.com>
Tested-by: Bernhard Sulzer <micraft.b@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct partition is the on-disk format of a MSDOS partition table entry.
Move it out of genhd.h into a new msdos_partition.h header and give it
a msdos_ prefix to avoid confusion.
Also move the magic number from block/partitions/msdos.h to the new
header so that it can be used by the SCSI drivers looking at the DOS
partition tables.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Call scsi_bios_ptable from scsi_partsize instead of requiring boilerplate
code in the callers. Also switch the calling convention to match that
of the ->bios_param instances calling this function, and use true/false
for the return value instead of the weird -1 convention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This avoids the need for a forward declaration and generally keeps the
file in the lower level first, high level last order.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use read_mapping_page and kmemdup instead of the odd read_dev_sector and
put_dev_sector helpers from the partitioning code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
block/genhd provides set_capacity_revalidate_and_notify() for sending RESIZE
notifications via uevents. This notification is newly added to scsi sd.
Signed-off-by: Balbir Singh <sblbir@amazon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Removed the common length and introduce read and write length for IOCTL
payload structure.
[mkp: fixed SoB ordering]
Link: https://lore.kernel.org/r/20200316074906.9119-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <viswas.g@microchip.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the sysfs attribute for non fatal log so that management utility can
get the non fatal dump from driver. The non-fatal error is an error
condition or abnormal behavior detected by the host, or detected and
reported by the controller to the host.The non-fatal error does not stop
the controller firmware and enables it to still respond to host requests.
A typical example of a non-fatal error is an I/O timeout or an unusual
error notification from the controller. Since the firmware is operational,
the error dump information is pushed to host memory (by firmware) upon
request from the host.
Link: https://lore.kernel.org/r/20200316074906.9119-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Move the instance tracking down after we think the instance is good to
go. Avoids having a use-after free.
2) There are goto targets for trying to cleanup if the hw fails to
initialize, but there's some overlap depending on who thinks they own
the sub-structures.
Link: https://lore.kernel.org/r/20200316074906.9119-5-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Peter Chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm80xx driver, the command mpi_set_phy_profile_req is sent by host
during boot to configure the phy profile such as analog setting page, rate
control page. However, the tag is not freed when its response is
received. As a result, 16 tags are missing for each HBA after boot. When
NCQ is enabled with queue depth 16, it needs at least, 15 * 16 = 240 tags
for each HBA to achieve the best performance. In current pm80xx driver with
setting CCB_MAX = 256, the total number of tags in each HBA is 255 for data
IO. Hence, without returning those tags to the pool after boot, some device
will finally be forced to non-ncq mode by ATA layer due to excessive errors
(i.e. LLDD cannot allocate tag for queued task).
Link: https://lore.kernel.org/r/20200316074906.9119-4-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: yuuzheng <yuuzheng@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A kexec reboot causes the controller fw to assert. This assertion shows up
in two ways, the controller doesn't show up as ready and an interrupt is
waiting as soon as the handler is registered. To resolve this added below
fix:
- Split the interrupt handling setup into two parts, setup and request.
- If the controller ready register indicates not-ready, but that the not
readiness is only on the IOC units we can still try a reset to bring the
system back to the pre-reboot state.
Link: https://lore.kernel.org/r/20200316074906.9119-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increasing the per-request size maximum (max_sectors_kb) runs into the
per-device DMA scatter gather list limit (max_segments) for users of the io
vector system calls (eg, readv and writev). This is because the kernel
combines io vectors into DMA segments when possible, but it doesn't work
for our user because the vectors in the buffer cache get scrambled. This
change bumps the advertised max scatter gather length to 528 to cover 2M w/
x86's 4k pages and some extra for the user checksum. It trims the size of
some of the tables we don't care about and exposes all of the command slots
upstream to the SCSI layer. Also reduced the PM8001_MAX_CCB to 256 as
pm8001 driver has memory limit depend on machine capability. If we increase
the sg length, we need to trade-off it by decreasing PM8001_MAX_CCB.
PM8001_MAX_CCB = 256 does not have any influence on normal use
Link: https://lore.kernel.org/r/20200316074906.9119-2-deepak.ukey@microchip.com
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Peter Chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
Link: https://lore.kernel.org/r/20200315094241.9086-9-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: Don Brace <don.brace@microsemi.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
Link: https://lore.kernel.org/r/20200315094241.9086-8-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
Also corrected the wrongly passed limit size. The remaining buffer size
must be decremented.
Link: https://lore.kernel.org/r/20200315094241.9086-7-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
Link: https://lore.kernel.org/r/20200315094241.9086-6-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: Brian King <brking@us.ibm.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
[mkp: checkpatch fix]
Link: https://lore.kernel.org/r/20200315094241.9086-5-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: Achim Leubner <achim_leubner@adaptec.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
Link: https://lore.kernel.org/r/20200315094241.9086-4-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: Satish Kharat <satishkh@cisco.com>
Cc: Sesidhar Baddela <sebaddel@cisco.com>
Cc: Karan Tilak Kumar <kartilak@cisco.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
Link: https://lore.kernel.org/r/20200315094241.9086-3-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: Subbu Seetharaman <subbu.seetharaman@broadcom.com>
Cc: Ketan Mukadam <ketan.mukadam@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since snprintf() returns the would-be-output size instead of the actual
output size, the succeeding calls may go beyond the given buffer limit.
Fix it by replacing with scnprintf().
Link: https://lore.kernel.org/r/20200315094241.9086-2-tiwai@suse.de
Cc: "James E . J . Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K . Petersen" <martin.petersen@oracle.com>
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: linux-scsi@vger.kernel.org
Acked-by: Balsundar P <Balsundar.P@microchip.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I/Os could be passed down while the device FC SCSI device is being deleted.
This would result in unnecessary delay of I/O and driver messages (when
extended logging is set).
[mkp: fixed commit hash and added SoB for Nilesh]
Link: https://lore.kernel.org/r/20200313085001.3781-1-njavali@marvell.com
Fixes: 3c75ad1d87 ("scsi: qla2xxx: Remove defer flag to indicate immeadiate port loss") # v5.6-rc1+
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This makes the SCSI tracing code slightly easier to read.
Link: https://lore.kernel.org/r/20200313203102.16613-6-bvanassche@acm.org
Fixes: bf81623542 ("[SCSI] add scsi trace core functions and put trace points")
Cc: Christoph Hellwig <hch@lst.de>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use these functions instead of open-coding them.
Link: https://lore.kernel.org/r/20200313203102.16613-5-bvanassche@acm.org
Cc: Kai Makisara <Kai.Makisara@kolumbus.fi>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The print of pr_err() does not come with device information, so replace it
with dev_err(). Also improve the grammar in the message.
Link: https://lore.kernel.org/r/1583940144-230800-1-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large queues of I/O to offline devices that are eventually submitted when
devices are unblocked result in a many repeated "rejecting I/O to offline
device" messages. These messages can fill up the dmesg buffer in crash
dumps so no useful prior messages remain. In addition, if a serial console
is used, the flood of messages can cause a hard lockup in the console code.
Introduce a flag indicating the message has already been logged for the
device, and reset the flag when scsi_device_set_state() changes the device
state.
Link: https://lore.kernel.org/r/20200311143930.20674-1-emilne@redhat.com
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This file had its own peculiar style, not following any other
files inside the Kernel (as far as I saw).
Had to do a number of changes here, starting by removing the two
leading asterisks from each line, adding table and literal
block markups and changing whitespace and blank lines.
The end result is that (IMHO), it is now a lot easier to read
it as a text file, while producing a good html output.
Link: https://lore.kernel.org/r/6f8e4da4ea643adbe048f55504a59427c5e50c97.1583136624.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Having this log in a ring buffer helps to diagnose qla2xxx driver and
firmware issues instead of having to reproduce the problem with
extended_logging enabled. This saves cycles and helps when it is hard
to reproduce problem.
Link: https://lore.kernel.org/r/1581557368-32080-1-git-send-email-rajan.shanmugavelu@oracle.com
Reviewed-by: Joe Jin <joe.jin@oracle.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Rajan Shanmugavelu <rajan.shanmugavelu@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device quirk "UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE" is enabled for all
Samsung devices by default currently.
However MediaTek UFS host requires different host PA_TACTIVATE
configuration. Hence clear this quirk first and then apply vendor-specific
value in vops callback.
Link: https://lore.kernel.org/r/20200302135346.16797-1-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix up a compiler warning introduced via 54b04c99d02e
Link: https://lore.kernel.org/r/1583159961-15903-1-git-send-email-brking@linux.vnet.ibm.com
Fixes: 54b04c99d02e ("scsi: ibmvfc: Avoid loss of all paths during SVC node reboot")
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iSCSI session destruction can be arbitrarily slow, since it might require
network operations and serialization inside the SCSI layer. This patch
adds a new user event to trigger the destruction work asynchronously,
releasing the rx_queue_mutex as soon as the operation is queued and before
it is performed. This change allows other operations to run in other
sessions in the meantime, removing one of the major iSCSI bottlenecks for
us.
To prevent the session from being used after the destruction request, we
remove it immediately from the sesslist. This simplifies the locking
required during the asynchronous removal.
Link: https://lore.kernel.org/r/20200227195945.761719-1-krisman@collabora.com
Co-developed-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Co-developed-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the occasional adapter panic when sg_reset is issued with -d, -t, -b
and -H flags. Removal of command type HBA_IU_TYPE_SCSI_TM_REQ in
aac_hba_send since iu_type, request_id and fib_flags are not populated.
Device and target reset handlers are made to send TMF commands only when
reset_state is 0.
Link: https://lore.kernel.org/r/1581553771-25796-1-git-send-email-Sagar.Biradar@microchip.com
Reviewed-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Signed-off-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an SVC node goes down as part of a node reboot, its WWPNs are moved to
the remaining node. When the node is back online, its WWPNs are moved
back. The result is that the WWPN moves from one NPort_ID to another, then
back again. The ibmvfc driver was forcing the old port to be removed, but
not sending an implicit logout. When the WWPN showed up at the new
location, the PLOGI failed as there was already a login established for the
old scsi id. The patch below fixes this by ensuring we always send an
implicit logout for any scsi id associated with an rport prior to calling
fc_remote_port_delete.
Link: https://lore.kernel.org/r/1582767943-16611-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these ones is a flexible array member[1][2], introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by this
change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Link: https://lore.kernel.org/r/20200224161406.GA21454@embeddedor
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When trying to rescan disks in petitboot shell, we hit the following
softlockup stacktrace:
Kernel panic - not syncing: System is deadlocked on memory
[ 241.223394] CPU: 32 PID: 693 Comm: sh Not tainted 5.4.16-openpower1 #1
[ 241.223406] Call Trace:
[ 241.223415] [c0000003f07c3180] [c000000000493fc4] dump_stack+0xa4/0xd8 (unreliable)
[ 241.223432] [c0000003f07c31c0] [c00000000007d4ac] panic+0x148/0x3cc
[ 241.223446] [c0000003f07c3260] [c000000000114b10] out_of_memory+0x468/0x4c4
[ 241.223461] [c0000003f07c3300] [c0000000001472b0] __alloc_pages_slowpath+0x594/0x6d8
[ 241.223476] [c0000003f07c3420] [c00000000014757c] __alloc_pages_nodemask+0x188/0x1a4
[ 241.223492] [c0000003f07c34a0] [c000000000153e10] alloc_pages_current+0xcc/0xd8
[ 241.223508] [c0000003f07c34e0] [c0000000001577ac] alloc_slab_page+0x30/0x98
[ 241.223524] [c0000003f07c3520] [c0000000001597fc] new_slab+0x138/0x40c
[ 241.223538] [c0000003f07c35f0] [c00000000015b204] ___slab_alloc+0x1e4/0x404
[ 241.223552] [c0000003f07c36c0] [c00000000015b450] __slab_alloc+0x2c/0x48
[ 241.223566] [c0000003f07c36f0] [c00000000015b754] kmem_cache_alloc_node+0x9c/0x1b4
[ 241.223582] [c0000003f07c3760] [c000000000218c48] blk_alloc_queue_node+0x34/0x270
[ 241.223599] [c0000003f07c37b0] [c000000000226574] blk_mq_init_queue+0x2c/0x78
[ 241.223615] [c0000003f07c37e0] [c0000000002ff710] scsi_mq_alloc_queue+0x28/0x70
[ 241.223631] [c0000003f07c3810] [c0000000003005b8] scsi_alloc_sdev+0x184/0x264
[ 241.223647] [c0000003f07c38a0] [c000000000300ba0] scsi_probe_and_add_lun+0x288/0xa3c
[ 241.223663] [c0000003f07c3a00] [c000000000301768] __scsi_scan_target+0xcc/0x478
[ 241.223679] [c0000003f07c3b20] [c000000000301c64] scsi_scan_channel.part.9+0x74/0x7c
[ 241.223696] [c0000003f07c3b70] [c000000000301df4] scsi_scan_host_selected+0xe0/0x158
[ 241.223712] [c0000003f07c3bd0] [c000000000303f04] store_scan+0x104/0x114
[ 241.223727] [c0000003f07c3cb0] [c0000000002d5ac4] dev_attr_store+0x30/0x4c
[ 241.223741] [c0000003f07c3cd0] [c0000000001dbc34] sysfs_kf_write+0x64/0x78
[ 241.223756] [c0000003f07c3cf0] [c0000000001da858] kernfs_fop_write+0x170/0x1b8
[ 241.223773] [c0000003f07c3d40] [c0000000001621fc] __vfs_write+0x34/0x60
[ 241.223787] [c0000003f07c3d60] [c000000000163c2c] vfs_write+0xa8/0xcc
[ 241.223802] [c0000003f07c3db0] [c000000000163df4] ksys_write+0x70/0xbc
[ 241.223816] [c0000003f07c3e20] [c00000000000b40c] system_call+0x5c/0x68
As a part of the scan process Linux will allocate and configure a
scsi_device for each target to be scanned. If the device is not present,
then the scsi_device is torn down. As a part of scsi_device teardown a
workqueue item will be scheduled and the lockups we see are because there
are 250k workqueue items to be processed. Accoding to the specification of
SIS-64 sas controller, max_channel should be decreased on SIS-64 adapters
to 4.
The patch fixes softlockup issue.
Thanks for Oliver Halloran's help with debugging and explanation!
Link: https://lore.kernel.org/r/1583510248-23672-1-git-send-email-wenxiong@linux.vnet.ibm.com
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before access auto hibner8 timer register, make sure power and clock are
properly configured to avoid unclocked register access.
Link: https://lore.kernel.org/r/1583398391-14273-1-git-send-email-cang@codeaurora.org
Fixes: ba7af5ec51 ("scsi: ufs: export ufshcd_auto_hibern8_update for vendor usage")
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().
The original code used a for-loop that looped over each of the 8 bytes
and copied them into a temporary buffer. pci_get_dsn() uses two calls to
pci_read_config_dword, and correctly bitwise ORs them into a u64. Thus,
we can simplify the snprintf significantly using %016llX on a u64 value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lrbp->cmd is set only for SCSI commands. Use this knowledge to simplify two
boolean expressions.
Link: https://lore.kernel.org/r/20200123035637.21848-4-bvanassche@acm.org
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but makes the next patch in
this series easier to read.
Link: https://lore.kernel.org/r/20200123035637.21848-3-bvanassche@acm.org
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current behavior of the SCSI core is to clear driver-private data
before preparing a request for submission to the SCSI LLD. Make it possible
for SCSI LLDs to disable clearing of driver-private data.
These hooks will be used by a later patch, namely "scsi: ufs: Let the SCSI
core allocate per-command UFS data".
Link: https://lore.kernel.org/r/20200123035637.21848-2-bvanassche@acm.org
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove cmd_list functionality; no users left. With that the
scsi_put_command() becomes empty, so remove that one, too.
Link: https://lore.kernel.org/r/20200228075318.91255-14-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the SCSI midlayer helper to traverse the number of outstanding
commands. This also eliminates the last usage for the cmd_list
functionality so we can drop it.
Link: https://lore.kernel.org/r/20200228075318.91255-13-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Balsundar P <balsundar.p@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of traversing the list of possible commands by hands we should be
using scsi_host_busy_iter() to figure out if there are outstanding
commands.
Link: https://lore.kernel.org/r/20200228075318.91255-12-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Balsundar P < Balsundar.P@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add an iterator scsi_host_busy_iter() to traverse all busy commands. If
locking against concurrent command completions is required, it has to be
provided by the caller.
Link: https://lore.kernel.org/r/20200228075318.91255-11-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use scsi_host_block() and scsi_host_unblock() instead of
scsi_block_requests()/scsi_unblock_requests() to block and unblock I/O.
This has the advantage that the block layer will stop sending I/O to the
adapter instead of having the SCSI midlayer requeueing I/O internally.
Link: https://lore.kernel.org/r/20200228075318.91255-10-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Balsundar P < Balsundar.P@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add helper functions to call scsi_internal_device_block()/
scsi_internal_device_unblock() for all attached devices on a SCSI host.
Link: https://lore.kernel.org/r/20200228075318.91255-9-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
_aac_reset_adapter() only has one caller, and that one already calls
scsi_block_requests(). Move the calls out of _aac_reset_adapter() to avoid
calling scsi_block_requests() twice.
Link: https://lore.kernel.org/r/20200228075318.91255-8-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Balsundar P < Balsundar.P@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the midlayer helper scsi_host_complete_all_commands() to flush all
outstanding commands.
Link: https://lore.kernel.org/r/20200228075318.91255-7-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Balsundar P <balsundar.p@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use scsi_host_complete_all_commands() to terminate all outstanding commands
and change the command result for terminated commands to the more common
'DID_RESET' instead of 'QUEUE_FULL'.
Link: https://lore.kernel.org/r/20200228075318.91255-6-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Balsundar P <balsundar.p@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no need to wait for outstanding write commands on synchronize
cache; the block layer is responsible for I/O scheduling, no need to
out-guess it in the driver layer.
Link: https://lore.kernel.org/r/20200228075318.91255-5-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Balsundar P <balsundar.b@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rather than traversing all outstanding commands manually, use the
scsi_host_complete_all_commands() helper to terminate all commands during
reset. With that we can drop the cmd_list usage from the midlayer.
Link: https://lore.kernel.org/r/20200228075318.91255-4-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a helper scsi_host_complete_all_commands() to terminate all outstanding
commands on a SCSI host.
Link: https://lore.kernel.org/r/20200228075318.91255-3-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the badly named function into adpt_i2o_scsi_complete(), and make it
a void function as the return value is never used. This also fixes a
potential use-after-free as the return value might be evaluated from the
command result after the command has been freed.
Link: https://lore.kernel.org/r/20200228075318.91255-2-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use kobj_to_dev to instead of open-coding it.
Link: https://lore.kernel.org/r/20200225100411.10250-1-guosongsu@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Guosong Su <suguosong@xiaomi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some delays may be required either after gating or before ungating
reference clock for device according to vendor requirements.
Note that in UFS 3.0, the delay time after gating reference
clock can be defined by attribute bRefClkGatingWaitTime. Use the
formal value instead if it can be queried from device.
Link: https://lore.kernel.org/r/20200220134848.8807-2-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Western Digital UFS devices require host's PA_TACTIVATE to be lower than
device's PA_TACTIVATE, otherwise it may get stuck during hibern8 sequence.
Link: https://lore.kernel.org/r/1582517363-11536-3-git-send-email-cang@codeaurora.org
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently ufshcd_vops_apply_dev_quirks() comes after all UniPro parameters
have been tuned. Move it up so that vendors have a chance to apply device
quirks in advance.
Link: https://lore.kernel.org/r/1582517363-11536-2-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use an enum to specify the various quirks instead of #defines inside the
structure definition.
[mkp: fix typo]
Link: https://lore.kernel.org/r/20200221140812.476338-3-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove various quirks that don't have users, as well as the dead code keyed
off them.
Link: https://lore.kernel.org/r/20200221140812.476338-2-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When transitioning from loop to N2N, stale NPort ID is not
re-assigned. Stale ID can collide with remote device. This patch will
re-assign NPort ID on N2N is detected.
Link: https://lore.kernel.org/r/20200226224022.24518-18-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Asutosh Das