This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP
board file supports only minimal set of drivers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch update the common clock.c file for OMAP4. The clk_get() and
clk_put() functions are moved to common place in arch/arm/common/clkdev.c
Since on current OMAP4 platform clk management is still not supported, the
platform file is stubbed with those functions.
Once the framework is ready, this WILL be replaced with a full
clkdev implementation.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for keypad, GPIO keys and LEDs. Also enable hardware
debounce feature for GPIO keys.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup regulators for MMC1 and MMC2 to get those SD slots
working again.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
CC: David Brownell <david-b@pacbell.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize regulators for Beagle and Overo.
Patch is based on earlier patches posted to linux-omap mailing
list.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Stanley.Miao <stanley.miao@windriver.com>
with board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Qimonda HYB18M512160AF-6 SDRAM chip, used on
the OMAP3430SDP boards.
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chip used on 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards. Original timing data is from the Micron
datasheet PDF downloaded from:
http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move platform_device_register() for serial device to
omap_serial_init()
There is no need to have arch_initcall() dependency in serial
as already board files call the function omap_serial_init()
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are not being used right now, and the processor specific
defines should be used instead by any code accessing these registers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make 770 LCD work by adding clk_add_alias().
Also remove the old unused functions.
Note that the clk_add_alias() could probably be moved
to arch/arm/clkdev.c later on.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com
Based on an earlier patch by Hunyue Yau <hyau@mvista.com> with
board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Hunyue Yau <hyau@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert the board-rx51 smc91x code to be generic and make
the boards to use it. This allows future recalculation of the
timings when the source clock gets scaled.
Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL.
Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing
calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add generic onenand support when connected to GPMC and make the
boards to use it.
The patch has been modified to make it more generic to support all
the boards with GPMC. The patch also remove unused prototype for
omap2_onenand_rephase(void).
Note that board-apollon.c is currently using the MTD_ONENAND_GENERIC
and setting the GPMC timings in the bootloader. Setting the GPMC
timings in the bootloader will not allow supporting frequency
scaling for the onenand source clock.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Original OMAP DMA chaining design had chain_id as one of the callback
parameters. Patch 538528de0c changed it
to use logical channel instead.
Correct the naming for callback to also use logical channel number
instead of the chain_id.
More details are on this email thread:
http://marc.info/?l=linux-omap&m=122961071931459&w=2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement transparent copy and constant fill features for OMAP2/3.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add cmpxchg/cmpxchg64 support for ARMv6K and ARMv7 systems
(original patch from Catalin Marinas <catalin.marinas@arm.com>)
The cmpxchg and cmpxchg64 functions can be implemented using the
LDREX*/STREX* instructions. Since operand lengths other than 32bit are
required, the full implementations are only available if the ARMv6K
extensions are present (for the LDREXB, LDREXH and LDREXD instructions).
For ARMv6, only 32-bits cmpxchg is available.
Mathieu :
Make cmpxchg_local always available with best implementation for all type sizes (1, 2, 4 bytes).
Make cmpxchg64_local always available.
Use "Ir" constraint for "old" operand, like atomic.h atomic_cmpxchg does.
Change since v3 :
- Add "memory" clobbers (thanks to Nicolas Pitre)
- removed __asmeq(), only needed for old compilers, very unlikely on ARMv6+.
Note : ARMv7-M should eventually be ifdefed-out of cmpxchg64. But it's not
supported by the Linux kernel currently.
Put back arm < v6 cmpxchg support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mathieu Desnoyers pointed out that the ARM barriers were lacking:
- cmpxchg, xchg and atomic add return need memory barriers on
architectures which can reorder the relative order in which memory
read/writes can be seen between CPUs, which seems to include recent
ARM architectures. Those barriers are currently missing on ARM.
- test_and_xxx_bit were missing SMP barriers.
So put these barriers in. Provide separate atomic_add/atomic_sub
operations which do not require barriers.
Reported-Reviewed-and-Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update OMAP1-specific PM infrastructure. This is a sync of what is in
linux-omap for OMAP1.
This mostly de-couples OMAP1 PM from OMAP2/3 PM and renames things
accordingly, and removes omap2/3 specific code from OMAP1 specific
headers.
Original OMAP1 decoupling patch for OMAP PM branch by Paul Walmsley.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.
Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes it possible to change uart sleep timeout. New sysfs
entry is added (/sys/devices/platform/serial8250.<uart>/sleep_timeout)
Writing zero will disable the timeout feature and prevent UART clocks
from being disabled.
Also default timeout is increased to 5 second to make serial console
more usable.
Original patch was written by Tero Kristo.
Cc: Tero Kristo <Tero.Kristo@nokia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention. The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup. The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.
While the activity timer is active, the smart-idle mode of the UART is
also disabled. This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.
Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.
In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.
Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.
Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add common omap2/3 function to check wether there is irq pending.
Switch to use it in omap2 pm code instead of its own.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
changes since v1: we now check if the parent configuration bit was
changed since reset and change the parent when needed.
csi_clk parent was defined with ahb_clk. However, according to the
m31 reference manual, it should be serial_pll_clk.
Guennadi always used a 20 MHz clock that was by chance changed to
a 45 MHz that fits in the mt9t031 spec. Now the clocks are computed
and output correctly (measured on oscillo).
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On MP systems, the data loaded by CPU0 before the SCU was initialised
may not be visible to the other CPUs.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This also includes the following compile fix:
This patch includes 'asm/cacheflush.h' which is needed to use
'flush_cache_all()' function.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 5461af5af5.
Adding a disable hook to the irq_chip is not the way to fix the
problem being addressed by this patch. Instead, we need to fix
support for [enable|disable]_irq_wake().
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The watchdog code currently hardcodes the base address
of the timer its using. To support new SoCs, make it
support timers at any address. Use the soc_info structure
to do this.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The davinci timer code currently hardcodes the timer register
base addresses, the timer irq numbers, and the timers to use
for clock events and clocksource. This won't work for some
a new SoC so put those values into the soc_info structure
and set them up in the SoC-specific files.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use the SoC infrastructure to hold the interrupt controller
information (i.e., base address, default priorities,
interrupt controller type, and the number of IRQs).
The interrupt controller base, although initially put
in the soc_info structure's intc_base field, is eventually
put in the global 'davinci_intc_base' so the low-level
interrupt code can access it without a dereference.
These changes enable the SoC default irq priorities to be
put in the SoC-specific files, and the interrupt controller
to be at any base address.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The pinmux register base and setup can be different for different
SoCs so move the pinmux reg base, pinmux table (and its size) to
the SoC infrastructure.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current code to support the DaVinci Power and Sleep Controller (PSC)
assumes that there is only one controller. This assumption is no longer
valid so expand the support to allow greater than one PSC.
To accomplish this, put the base addresses for the PSCs in the SoC
infrastructure so it can be referenced by the PSC code. This also
requires adding an extra parameter to davinci_psc_config() to specify
the PSC that is to be enabled/disabled.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
All of the davinci SoCs need to call davinci_clk_init() so
put the call in the common init routine.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The Davinci cpu_is_davinci_*() macros use the SoC part number
and variant retrieved from the JTAG ID register to determine the
type of cpu that the kernel is running on. Currently, the code to
read the JTAG ID register assumes that the register is always at
the same base address. This isn't true on some newer SoCs.
To solve this, have the SoC-specific code set the JTAG ID register
base address in soc_info structure and add a 'cpu_id' member to it.
'cpu_id' will be used by the cpu_is_davinci_*() macros to match
the cpu id. Also move the info used to identify the cpu type into
the SoC-specific code to keep all SoC-specific code together.
The common code will read the JTAG ID register, search through
an array of davinci_id structures to identify the cpu type.
Once identified, it will set the 'cpu_id' member of the soc_info
structure to the proper value and the cpu_is_davinci_*() macros
will now work.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Create a structure to encapsulate SoC-specific information.
This will assist in generalizing code so it can be used by
different SoCs that have similar hardware but with minor
differences such as having a different base address.
The idea is that the code for each SoC fills out a structure
with the correct information. The board-specific code then
calls the SoC init routine which in turn will call a common
init routine that makes a copy of the structure, maps in I/O
regions, etc.
After initialization, code can get a pointer to the structure
by calling davinci_get_soc_info(). Eventually, the common
init routine will make a copy of all of the data pointed to
by the structure so the original data can be made __init_data.
That way the data for SoC's that aren't being used won't consume
memory for the entire life of the kernel.
The structure will be extended in subsequent patches but
initially, it holds the map_desc structure for any I/O
regions the SoC/board wants statically mapped.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for DM646x SoC (a.k.a DaVinci HD) and its Evalution
Module (EVM.)
Original support done by Sudhakar Rajashekhara.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In addition, add board support for the DM355 Evaluation Module (EVM)
and the DM355 Leopard board.
Original DM355 EVM support done by Sandeep Paulraj, with significant
updates and improvements by David Brownell. DM355 Leopord support
done by Koen Kooi.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for Texas Instuments Common Platform Interrupt Controller
(cp_intc) used on DA830/OMAP-L137.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The davinci pre-kernel boot code assumes that all platforms use the
same UART base address for the console. That assumption is not longer
valid with some newer SoCs so determine the console UART base address
from the machine number passed in from bootloader.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch defines debug macros for low-level debugging for Davinci
based platforms
Tested on :
- DM644x DaVinci EVM
- DM646X DaVinciHD EVM
- DM355 EVM
This patch attempts to solve the low-level debug issue in DM646x. The
UART on DM646x SoC allows only 32-bit access. The existing
debug-macro.S uses the macros from debug-8250.S file. This led to
garbage serial out in the case of DM646x.
The inclusion of debug-8250.S does not allow for run time fix for this
issue. There are compile time errors due to multiple definitions of
the macros. Also when building a single image for multiple DaVinci
Platforms, the ifdefs cannot be relied upon.
The solution below does not include the debug-8250.S file and defines
the necessary macros. This solution was arrived at after observing
that word access does not affect the low-level debug messages on
DM644x/DM355.
The other approach to this issue is to use the UART module information
available in the peripheral registers to decide the access
mechanism. But this will have to be done for every access of UART
specifically for DM646x. Also this calls for a modification of the
debug-8250.S file.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch seems to get me much more reliable performance using the
GPIO banked interrupts on dm355 for the dm9000 driver.
Changes include:
- init GPIO handling along with normal GPIO init
- mask the level-sensitive bank IRQ during handling
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix two IRQ triggering bugs affecting GPIO IRQs:
- Make sure enabling with IRQ_TYPE_NONE ("default, unspecified")
isn't a NOP ... default to both edges, at least one must work.
- As noted by Kevin Hilman, setting the irq trigger type for a
banked gpio interrupt shouldn't enable irqs that are disabled.
Since GPIO IRQs haven't been used much yet, it's not clear these
bugs could have affected anything. The few current users don't
seem to have been obviously suffering from these issues.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On Mon, 25 May 2009 18:33:28 +0200
Valentin Longchamp <valentin.longchamp@epfl.ch> wrote:
> Hello,
>
> I have updated my mxc git tree and given a compilation spin to your
> board support and I have comments. See below.
>
>
> What's the point of declaring this new function, if all it does is
> calling the already existing one ? Furthermore, in the current
> mxc-master tree, mxc_map_io() does not exist anymore, it should be
> mx31_map_io (this breaks compilation for your board).
>
This patch solve those two issues. Until now i based my patches to
vanilla tree. This evening I cloned the mxc-master tree so i could
update the armadillo 500 support within recent platform changes.
The patch:
From e986a8dc262e5292350d95bf65ead75baf3272d7 Mon Sep 17 00:00:00 2001
From: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Date: Mon, 25 May 2009 22:24:03 +0200
Subject: [PATCH] Armadillo 500 removing useless function armadillo5x0_map_io
and use machine specific io mapping
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the SMSC911x chip found on the lilly-1131 module.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support code for lilly-1131 is implemented in a module/baseboard
fashion. All code specific to peripherals found on the development board
will go to this file.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based
modules. The module needs a baseboard support to work which will be
added in the next patch.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch removes unnecessary omap2_globals and pass the global structures
directly as function argument.
The proposed cleanup was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes fixes omap_sram_error() function and replace the
error paths with BUG_ON.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the compiler warning "assignment from incompatible
pointer type" in dmtimer.c and removes the tye casts. These warnings
were suppressed by type catsing.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
This email address is going to expire soon so update it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If XSYNCERR or RSYNCERR interrupts are enabled, they are never
cleared causing the IRQ handler to be continuously called.
This patch clears the IRQs in question in the event they are
enabled and taken.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This increases VMALLOC_END to 0x18000000, making room for 256MB
RAM with the default 128MB vmalloc region.
Note that after this patch there's no longer a hole between vmalloc
space and the beginning of IO space on omap2 as the first virtual
mapping starts at 0xd8000000.
Also fold in a related change from Paul Walmsley <paul@pwsan.com>
to change the OMAP2_SRAM addresses accordingly.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes unnecessary omap2_globals and pass the global structures
directly as function argument.
The proposed cleanup was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes fixes omap_sram_error() function and replace the
error paths with BUG_ON.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the compiler warning "assignment from incompatible
pointer type" in dmtimer.c and removes the tye casts. These warnings
were suppressed by type catsing.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updated defconfig for ep93xx. By default, support for all boards which
boot from 0x00000000 (SDCE3/SyncBoot) is included. Also updated the
defconfig to use EABI for building the kernel.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a Kconfig option to select between ep93xx boards which
boot from the SDRAM bank at 0x00000000 (SDCE3/SyncBoot) and those which
boot from 0xc0000000 (SDCE0). This corrects a problem which causes
invalid images to be built for boards which boot from 0xc0000000.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ASoC driver for AT91SAM9260-based AFEB9260 board
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our signal syscall restart handling for these kernels still uses
the userspace stack to build code for restarting the syscall.
Unfortunately, fixing this is non-trivial, and so for the time
being, we resolve the problem by disabling NX support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit eb0519b5a1, mv643xx_eth is non functional on ARM because
the platform device declaration does not include any coherent DMA mask
and coherent memory allocations fail.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch modifies parameter of clksrc_read() from 'void' to
'struct clocksource *cs', which fixes compile warning for
incompatible parameter type.
Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Currently "tidspbridge" driver uses its own mmu implementation and
will migrate to use this "omap iommu" eventually. This config is
provided to make this migration happen smoothly.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Remove explicit names from platform device resources since they will
automatically be named after the platform device they're associated
with.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
For the QNAP TS-119 and TS-219 the wrong MPPs were used for the SATA
activity/presence LEDs. The new settings make these LEDs work as
expected.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Stephen Rothwell <sfr@canb.auug.org.au> writes:
> Today's linux-next build of at least some av32 and arm configs failed like this:
>
> arch/avr32/kernel/signal.c:216: error: conflicting types for 'restart_syscall'
> include/linux/sched.h:2184: error: previous definition of 'restart_syscall' was here
>
> Caused by commit 690cc3ffe3 ("syscall:
> Implement a convinience function restart_syscall") from the net tree.
Grrr. Some days it feels like all of the good names are already taken.
Let's just rename the two static users in arm and avr32 to get this
sorted out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a device drivers, which has a omap iommu, with
address mapping APIs between device virtual address(iommu), physical
address and MPU virtual address.
There are 4 possible patterns for iommu virtual address(iova/da) mapping.
|iova/ mapping iommu_ page
| da pa va (d)-(p)-(v) function type
---------------------------------------------------------------------------
1 | c c c 1 - 1 - 1 _kmap() / _kunmap() s
2 | c c,a c 1 - 1 - 1 _kmalloc()/ _kfree() s
3 | c d c 1 - n - 1 _vmap() / _vunmap() s
4 | c d,a c 1 - n - 1 _vmalloc()/ _vfree() n*
'iova': device iommu virtual address
'da': alias of 'iova'
'pa': physical address
'va': mpu virtual address
'c': contiguous memory area
'd': dicontiguous memory area
'a': anonymous memory allocation
'()': optional feature
'n': a normal page(4KB) size is used.
's': multiple iommu superpage(16MB, 1MB, 64KB, 4KB) size is used.
'*': not yet, but feasible.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
The arch_initcall() is too late for board initialisation to use
gpiolib when doing their machine specific initilisation via the
.init_machine callback.
Bring the file into line with the s3c64xx implementation and use
the core_initcall() to register the GPIO chips.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Several GPIO functions have been returning -1 to indicate
an error instead of returning a proper error code. Change
to return -EINVAL for invalid argument(s).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add rtc,kpi and usbd device platform_device define
in arch/arm/mach-w90x900/mach-w90p910evb.c.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add rtc,kpi and usbd device map_desc define in
/arch/arm/mach-w90x900/w90p910.c.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This moves the GPIO driver away from using __devinit and __devexit
It also removes all printk() in favor of using dev_* print macros
on pdev->dev struct instead. Surplus prints are removed, and the
platform_device_probe() function is used instead of putting a
.probe function in the platform driver struct.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The message was missing a severity macro so pick pr_debug().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the DMA blocks in the S3C64XX series of CPUS,
which are based on the ARM PL080 PrimeCell system.
Unfortunately, these DMA controllers diverge from the PL080
design by adding another DMA controller register and
configuration for OneNAND.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.
The following perl was used to change the files:
perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the new style of GPIO numbering by using a single
macro for each GPIO bank. This means S3C2410_GPA0 becomes
S3C2410_GPA(0), and so on.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C24XX_GPIO_BASE makes it difficult to compress the
GPIO number space, and is only used in a few places of
which everything outside arch/arm/plat-s3c24xx/gpiolib.c
will be removed as soon as possible.
Change gpiolib.c to use the S3C2410_GPxCON register addresses
as the base for each bank, thus eliminating S3C24XX_GPIO_BASE.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The <mach/regs-gpio.h> really does not need the input and output
pin configurations as these are standard and have a generic
representation (plus the s3c24xx gpio specific code is going to
be phased out soon).
The following sed was applied to remove the lines:
sed -i~ -e '/S3C2410_GP[A-Z][0-9]*_\INP/d' \
-e '/S3C2410_GP[A-Z][0-9]*_\OUTP/d' \
-e '/S3C2410_GPA[0-9]*_OUT/d'
to remove these.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In our recent changes, arch/arm/plat-s3c24xx/gpiolib.c needs
to have <linux/sysdev.h> included for it to build.
This fixes the following error/warnings:
arch/arm/plat-s3c/include/plat/pm.h:104: error: expected declaration specifiers or '...' before 'pm_message_t'
arch/arm/plat-s3c/include/plat/pm.h:104: warning: 'struct sys_device' declared inside parameter list
arch/arm/plat-s3c/include/plat/pm.h:104: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-s3c/include/plat/pm.h:105: warning: 'struct sys_device' declared inside parameter list
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently spitz_ohci_init() that requests GPIO doesn't have
corresponding spitz_ohci_exit() which will gpio_free(). This causes
minor problems e.g. during resume when the OHCI device can't be resumed.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
'mach-pxa' platforms currently rely on a bootloader to setup GPIO pins
and clear RDH (to enable inputs).
A kernel loaded by a 'minimal' bootloader, that doesn't touch any pins,
will not function correctly; inputs will remain disabled, even after the
pins are configured. The following change fixes the issue and has been
verified on Gumstix Verdex XL6P and a custom PXA270 platform.
Signed-off-by: Timothy Clacy <tcl@phaseone.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
I want to reuse tosa/spitz gpio_reset code, but my board needs the reset
gpio to be driven high during normal operation.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pfn_valid() is meant to be able to tell if a given PFN has valid memmap
associated with it or not. In FLATMEM, it is expected that holes always
have valid memmap as long as there is valid PFNs either side of the hole.
In SPARSEMEM, it is assumed that a valid section has a memmap for the
entire section.
However, ARM and maybe other embedded architectures in the future free
memmap backing holes to save memory on the assumption the memmap is never
used. The page_zone linkages are then broken even though pfn_valid()
returns true. A walker of the full memmap must then do this additional
check to ensure the memmap they are looking at is sane by making sure the
zone and PFN linkages are still valid. This is expensive, but walkers of
the full memmap are extremely rare.
This was caught before for FLATMEM and hacked around but it hits again for
SPARSEMEM because the page_zone linkages can look ok where the PFN linkages
are totally screwed. This looks like a hatchet job but the reality is that
any clean solution would end up consumning all the memory saved by punching
these unexpected holes in the memmap. For example, we tried marking the
memmap within the section invalid but the section size exceeds the size of
the hole in most cases so pfn_valid() starts returning false where valid
memmap exists. Shrinking the size of the section would increase memory
consumption offsetting the gains.
This patch identifies when an architecture is punching unexpected holes
in the memmap that the memory model cannot automatically detect and sets
ARCH_HAS_HOLES_MEMORYMODEL. At the moment, this is restricted to EP93xx
which is the model sub-architecture this has been reported on but may expand
later. When set, walkers of the full memmap must call memmap_valid_within()
for each PFN and passing in what it expects the page and zone to be for
that PFN. If it finds the linkages to be broken, it assumes the memmap is
invalid for that PFN.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i.MX31 PDK consists of several boards, one of them is a debug
board containing a CPLD which controls some debug leds, switch
buttons, an interrupt chip and an Ethernet controller.
This patch adds support for detecting if the PDK board is present
(during boot) and adds the interrupt chip to the kernel.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the newly moved <plat/watchdog-reset.h> to perform the
arch_reset() call which has been unimplemented for a while.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the watchdog reset code from <mach/system-reset.h> to
a new file <plat/watchdog-reset.h> as this code is needed
by both s3c2410, s3c64xx and soon-to-be added s3c24a0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The use of S3C2410_GP[A-Z]x_INP and S3C2410_GP[A-Z]x_OUTP are
very rare and are taking up large amounts of space in the
regs-gpio.h header.
The GPIO layer has had generic input and out defines called
S3C2410_GPIO_INPUT and S3C2410_GPIO_OUTPUT for a while which work
for all S3C24XX GPIOs.
Do the following replacements:
S3C2410_GP[A-Z][0-9]*_\OUTP => S3C2410_GPIO_OUTPUT
S3C2410_GP[A-Z][0-9]*_\INP => /S3C2410_GPIO_INPUT
S3C2410_GPA[0-9]*_OUT => S3C2410_GPIO_OUTPUT
to remove any usages of these and prepare the header for
the removal of these.
The following command was used to acheive this:
find . -type f -writable ! -name regs-gpio.h ! -name "*~" | xargs sed -i~ -e 's/S3C2410_GP[A-Z][0-9]*_\OUTP/S3C2410_GPIO_OUTPUT/g' -e 's/S3C2410_GP[A-Z][0-9]*_\INP/S3C2410_GPIO_INPUT/g' -e 's/S3C2410_GPA[0-9]*_OUT/S3C2410_GPIO_OUTPUT/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the s3c2410_gpio_irq2pin() function as it is not being
used in any in kernel driver and the function is probably not
being used anywhere else.
This is also part of the effort to remove any of the s3c24xx gpio
specific code that cannot be recreated by using the gpiolib
framework now in the kernel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The SCU can be used by non-realview platforms, so make it visible
for other people to use rather than having them copy the header file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Having discussed broadcast tick support with Thomas Glexiner, the
broadcast tick devices should be registered with a higher rating
than the global tick device, and it should have the ONESHOT and
PERIODIC feature flags set.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Thomas Glexiner <tglx@linutronix.de>
smp_cross_call_done() is a no-op for MPCore, and since it's only
used by platform code, there's no point in having it unless it's
doing something.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM SMP code wasn't properly updated for the cpumask changes, which
results in smp_timer_broadcast() broadcasting ticks to non-online CPUs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
convert callback
This patch allow us to efficiently modify the number of
remaining conversions from the client side. This us useful
when we do not know in advance how many conversions we will
need or when we need to cancel pending conversions.
This change is simple enough to be compatible with existing
code that can just define the new pointer in the callback
and ignore it.
Sample usage:
http://tinyurl.com/s3c2410-ts-c (function stylus_adc_action).
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Small cleanup.
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: rewrote subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add platform device definitions for the high-speed and OtG
capable device block on the newer Samsung parts.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Compilation for this board yields the following errors:
arch/arm/mach-pxa/viper.c:511: error: 'FFUART' undeclared here (not in a function)
arch/arm/mach-pxa/viper.c:520: error: 'BTUART' undeclared here (not in a function)
arch/arm/mach-pxa/viper.c:529: error: 'STUART' undeclared here (not in a function)
Fix them by including the necessary header.
Signed-off-by: Ricardo Martins <rasm@fe.up.pt>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the clkdev API support for the ep93xx uart clocks.
The uarts available in the ep93xx have individual clock controls.
The current implementation assumes that the bootloader has enabled
the clocks before the kernel has booted. It also assumes that the
bootloader has set the UARTBAUD bit indicating that the uarts are
running off the 14.7456MHz external crystal.
This fixes both issues. It also allows the uart clocks to be stopped
when there are no users.
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the framebuffer work on omap3.
Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".
Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.
This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per 3430 TRM, there are 6 banks [0 to 191]
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Restructure UART pin setup in preparation for adding other pins
in later patches.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
From ff1fd9d7015d9b9ad3e0df2016d0415e2719747c Mon Sep 17 00:00:00 2001
From: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Date: Fri, 15 May 2009 17:21:21 +0200
Subject: [PATCH] Make sure ipg_per_clk is generated by ipg_clk and not usb_pll
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Cirrus Logic EDB93xx development board platform init files
share redundant code. The only differences are in the flash
memory configuration, MACH_TYPE, and additional on-board
I2C devices. This patch merges all of them into one file.
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Cc: Toufeeq Hussain <toufeeq_hussain@infosys.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c24xx_register_clock() function has been doing a test
on clk->owner to see if it is NULL, and then setting itself
as the owner if clk->owner == NULL.
This is not needed, arch/arm/plat-s3c/clock.c cannot be
compiled as a module, and even if it was, it should not be
playing with this field if it being registered from somewhere
else.
The best course of action is to remove this bit of
code completely.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The BAST support code is calling s3c_i2c0_set_platdata() from
the map_io() entry, instead of the bast_init() code. This causes
the registration to fail due to kmalloc() not being available
at the time.
This fixes the following error:
s3c_i2c0_set_platdata: no memory for platform data
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix unused code warning in arch/arm/plat-s3c24xx/dma.c if there
is no PM support enabled. The function to_dma_chan() should
be marked inline so that the compiler will eliminate it without
warning if it isn't used.
arch/arm/plat-s3c24xx/dma.c:1239: warning: 'to_dma_chan' defined but not used
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix compilation bug when debug was enabled
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cleanup arm/plat-s3c64xx/include/plat/gpio-bank-h.h include file.
Using shift-left operation with value >32 is a bad habit.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The symbol 'floatx80_is_nan' prototype was defined
locally in fpa11_cprt.c when it was built outside the
file in softfloat-specialisze.
Move this into softfloat.h to fix the following sparse
warning:
softfloat-specialize:276:6: warning: symbol 'floatx80_is_nan' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add header file decleration for 'ExtendedCPDO' in fpa11.h
to stop the following sparse warning:
extended_cpdo.c:90:14: warning: symbol 'ExtendedCPDO' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is a build fix, resyncing the DaVinci EVM ASoC board code
with the version in the DaVinci tree. That resync includes
support for the DM355 EVM, although that board isn't yet in
mainline.
(NOTE: also includes a bugfix to the platform_add_resources
call, recently sent by Chaithrika U S <chaithrika@ti.com> but
not yet merged into the DaVinci tree.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On our system we see the following messages:
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...
The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.
Let's give them debugging level instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages. Same with
omap2_clksel_round_rate_div(). While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz. CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations. Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Renumber registers in omap3_sram_configure_core_dpll() assembly code to
make space for additional parameters.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialize SDRC_POWER to a known-good setting when the kernel boots.
Necessary since some bootloaders don't initialize SDRC_POWER properly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Clear the SDRC_POWER.PWRENA bit before putting the SDRAM into self-refresh
mode. This prevents the SDRC from attempting to power off the SDRAM,
which can cause the system to hang.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add more barriers in the SRAM CORE DPLL M2 divider change code.
- Add a DSB SY after the function's entry point to flush all cached
and buffered writes and wait for the interconnect to claim that they
have completed[1]. The idea here is to force all delayed write
traffic going to the SDRAM to at least post to the L3 interconnect
before continuing. If these writes are allowed to occur after the
SDRC is idled, the writes will not be acknowledged and the ARM will
stall.
Note that in this case, it does not matter if the writes actually
complete to the SDRAM - it is only necessary for the writes to leave
the ARM itself. If the writes are posted by the interconnect when
the SDRC goes into idle, the writes will be delayed until the SDRC
returns from idle[2]. If the SDRC is in the middle of a write when
it is requested to enter idle, the SDRC will not acknowledge the
idle request until the writes complete to the SDRAM.[3]
The old-style DMB in sdram_in_selfrefresh is now superfluous, so,
remove it.
- Add an ISB before the function's exit point to prevent the ARM from
speculatively executing into SDRAM before the SDRAM is enabled[4].
...
1. ARMv7 ARM (DDI 0406A) A3-47, A3-48.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
3. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
4. ARMv7 ARM (DDI 0406A) A3-48.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Mark the SRAM (aka OCM RAM) as Non-cacheable Normal memory[1]. This
is to prevent the ARM from evicting existing cache lines to SDRAM
while code is executing from the SRAM. Necessary since one of the
primary uses for the SRAM is to hold the code and data for the CORE
DPLL M2 divider reprogramming code, which must execute while the SDRC
is idled. If the ARM attempts to write cache lines back to the while
the SRAM code is running, the ARM will stall[2].
TI deals with this problem in the CDP kernel by marking the SRAM as
Strongly-ordered memory.
Tero Kristo <tero.kristo@nokia.com> caught a bug in an earlier version of
this patch - thanks Tero.
...
1. ARMv7 ARM (DDI 0406A) pp. A3-30, A3-31, B3-32.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
With the clkdev, musb_core.c needs to register clock with name "ick".
Once all the platforms using the musb driver have been converted
to use clockdev, the clock name does not need to be passed
from the low-level init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
SPI driver will do unhandled fault on OMAP2420 if trying to probe
non-existing SPI busses. Register those additional busses runtime only
for cpus having them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "tusb6010 init error 5, -19" and compilation warning from function
tusb6010_platform_retime "warning: 'sysclk_ps' is used uninitialized in this
function".
I suppose commit c094ba34b8f780885d029ce3c2715a194b780e5d was meant to test
for zero fclk_ps instead of sysclk_ps.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO de-bounce clocks don't have any impact on the module idle state, so
the clock code should not wait for the module to enable after the de-bounce
clocks are enabled.
Problem found by Kevin Hilman <khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Print reserved memory only if it was actually reserved.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
plat-omap/mailbox, floppy, viocd, mspro_block, i2o_block and
mmc/card/queue are already pretty close to dequeueing model and can be
converted with simple changes. Convert them.
While at it,
* xen-blkfront: !fs check moved downwards to share dequeue call with
normal path.
* mspro_block: __blk_end_request(..., blk_rq_cur_byte()) converted to
__blk_end_request_cur()
* mmc/card/queue: loop of __blk_end_request() converted to
__blk_end_request_all()
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
bonding: fix panic if initialization fails
IXP4xx: complete Ethernet netdev setup before calling register_netdev().
IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
ipvs: Fix IPv4 FWMARK virtual services
ipv4: Make INET_LRO a bool instead of tristate.
net: remove stale reference to fastroute from Kconfig help text
net: update skb_recycle_check() for hardware timestamping changes
bnx2: Fix panic in bnx2_poll_work().
net-sched: fix bfifo default limit
igb: resolve panic on shutdown when SR-IOV is enabled
wimax: oops: wimax_dev_add() is the only one that can initialize the state
wimax: fix oops if netlink fails to add attribute
Bluetooth: Move dev_set_name() to a context that can sleep
netfilter: ctnetlink: fix wrong message type in user updates
netfilter: xt_cluster: fix use of cluster match with 32 nodes
netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
netfilter: add missing linux/types.h include to xt_LED.h
mac80211: pid, fix memory corruption
mac80211: minstrel, fix memory corruption
cfg80211: fix comment on regulatory hint processing
...
From: Bruce Ashfield <bruce.ashfield@windriver.com>
To fully support the armv7-a instruction set/optimizations, support
for the R_ARM_MOVW_ABS_NC and R_ARM_MOVT_ABS relocation types is
required.
The MOVW and MOVT are both load-immediate instructions, MOVW loads 16
bits into the bottom half of a register, and MOVT loads 16 bits into the
top half of a register.
The relocation information for these instructions has a full 32 bit
value, plus an addend which is stored in the 16 immediate bits in the
instruction itself. The immediate bits in the instruction are not
contiguous (the register # splits it into a 4 bit and 12 bit value),
so the addend has to be extracted accordingly and added to the value.
The value is then split and put into the instruction; a MOVW uses the
bottom 16 bits of the value, and a MOVT uses the top 16 bits.
Signed-off-by: David Borman <david.borman@windriver.com>
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To avoid compile-time warning, added parameter to the stmp3xxx_clock_read
Signed-off-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Usb register controller header file dfine.
w90p910 usb ip is standard,but some mutifunction
controll pin must be special define in w90p910
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Clock register controller header file dfine.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add this touch screen driver relevant kernel parts.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add this usb host driver relevant kernel parts.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add irq number define for driver will be submitted.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add w90p910 IC other interface controller regester map
for driver will be submitted.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the camera device based on Guennadi's soc_camera architecture
for the mx31.
The proposed init by Guennadi was removed and must be implemented in the
board init file as it contains a lot of board specific info (memory
size, clock speed).
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is used on all board of our system, so again this is done in the
mx31moboard.c file.
changes since v2: call to gpio_request added in platform code, and
moved device initialization in baseboard files.
changes since v1: pins are claimed in another patch
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to use the gpiolib, we now have to call gpio_request in
the plaform code since it is not done in iomux code anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since iomux code is not directly related to gpio on mx31, the calls
to gpio_request are removed from iomux.c file.
These calls have to be done in platform initialization files. The
name of the singe pin call for iomux is also changed to
mxc_iomux_alloc_pin.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add OTG device definition and resources to i.MX31 and a pure USB device mode
support to the pcm037 board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add Sharp-QVGA panel support for MX27ADS board
Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the SMSC platform device to the Litekit board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several comments in board config files stated "mandatory for
CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This support both sdhc1 and sdhc2 with WP and CD for the marxbot and
devboard mx31moboard baseboards.
sdhc2 is present on both, but is not directly included in the
mx31moboard file because a third baseboard (not supported yet) without
sdhc2 is planned.
Changes since v1: removed pin initialization from init/exit function and
taken different comments into account
Changes since v2: pin initialiation now is done in another patch for all
current mx31moboard pins
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Changes since v1: all the pins needed for the drivers are claimed in
another patch
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As suggested by Sascha, here we setup all the pins that we are using in
the current (and currently reviewed) drivers for mx31moboard system.
changes since v1: changed I2C1 pin names
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As suggested by Sascha, I regroup them in a single patch so that the
other patches become more orthogonal.
changes since v1: changed I2C1 pin names
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This hw-random driver add support to RNGA hardware found
on some i.MX processors.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Various improvements (includes in alphabetical order, platform devices
declaration order change, ...)
The pins now are claimed in a single function call from a main table for
every board for a better clarity and to adopt the current agreement for
mx31 devices.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds a defconfig file for the i.MX21 SoC, targeting
the Freescale i.MX21ADS (M9328MX21ADSE) Application
Development System.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Kconfig enables now HAVE_PWM (this enables in turn the selection of
CONFIG_BACKLIGHT_PWM)
* changes CONFIG_ARCH_MXyy to CONFIG_MACH_MXyy
* fix some register names to match those of the reference manual
* write a stub code so that the PWM can be used to program the
LCD backlight
* convert from #ifdef CONFIG_ARCH_MXxx to cpu_is_mxXX()
* remove unneeded defines and fix 80-column "violations" of checkpatch.pl
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[PATCH v6] MXC: mx21ads base support
Base machine support for the Freescale i.MX21ADS
(M9328MX21ADSE) Application Development System.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MXC GPIO controller does not support generation of interrupts on both
edges. Emulate this mode in software by reconfiguring the irq trigger
polarity on each interrupt. This follows an example of
drivers/mfd/asic3.c.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch/arm/mach-imx from the kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we depend on hardcoded base addresses for the interrupt
controller. This prevents us from compiling in more than one i.MX
architecture at a time. This patch changes the base address to a
runtime calculated one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we depend on hardcoded base addresses for the timer.
This prevents us from compiling in more than one i.MX architecture
at a time. This patch changes the base address to a runtime
calculated one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to have more mapping functions for more than one
i.MX architecture in the kernel. As this is the earliest board
specific hook we have, also use it to set the cpu type.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It is no longer present in newer cores. Unfortunately Freescale decided
to put the bit which decides between automotive clock path and consumer
clock path in the automotive clock path direction. With current code we
cannot detect the core revision, so just remove automotive path completely.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This iomux is called iomux-v3 in the tree because it is the third known
incarnation of MXC iomuxers. It is not only found on the MX35 but also
on the MX51 and probably others.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As per commit 284901a90a, use
DMA_BIT_MASK(n)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add missing DMA controller block clocks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for S3C6400 SDHCI channels 0 and 1, making
the GPIO code common to both S3C6400 and S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add detection support for the S3C6400 SoC which has it's
id register in a different place to the S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.
Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the GPIO suspend/resume support inline with the gpiolib support
so that it will work with both the S3C24XX and S3C64XX series.
The s3c_gpio_chip is extended to have a pm callback and a save block
to keep the state of the GPIO over suspend, and the code from the
s3c24xx implementation is added to a new common file.
The suspend process now uses the list of registered chips to go through
saving and restoring each one as appropriate, using the pm callback to
select the appropriate routine depending on the type of control register
present.
This change also means that any additional GPIO added should not require
changes to the PM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for saving the state of the IRQ registers over suspend.
This requires moving the S3C64XX UART registers into <plat/regs-serial.h>
and adding irq-pm.c which saves the state of all the IRQ registers.
The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and
IRQ_EINT_GROUP registers as it was easier than adding three different
files. Also ensuring that all the registers are restored to the same
state as before suspend is considered to be the best thing to do.
Note, we do not suspend the VIC here, this is done by the VIC driver
itself.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add an s3c64xx_sysclass and device for items that currently
want to bind to any s3c64xx processor. The first user of this
will be parts of the s3c64xx suspend support which need to
save device state over suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial support for the S3C64XX based systems to use
suspend-to-RAM to sleep.
Includes basic debugging for use with the SMDK6410 usign the
LEDs on the baseboard.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a simple debug message on saving the UART state and add a per-arch
pre-restore function to be used by the s3c64xx restore code to ensure
the UARTs control registers do not go through any illegal state changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The USB host base address is available on both the S3C24XX and S3C64XX
ranges.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add USB OHCI host capability to the SMDK6410 for either USB OtG or
a single/double USB host port.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Santosh Shilimkar