Commit b7bb367afa added support for inserting delays in between
individual words within a single SPI transaction. This makes it
accessible from userspace.
WARNING: This delay is silently ignored unless the SPI controller
implements extra support for it. This is similar to how the in-kernel
users handle the other existing property, spi_transfer->word_delay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_transfer *t will be used in one transfer whatever. If t is NULL,
there has no need to try sending data, so add an error return here.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add dma mode support for LPSPI. Any frame longer than half txfifosize will
be sent by dma mode.
For now, there are some limits:
1. The maximum transfer speed in master mode depends on the slave device,
at least 40MHz(tested by spi-nor on 8qm-lpddr4-arm2 base board);
2. The maximum transfer speed in slave mode is 15MHz(imx7ulp),
22MHz(8qm/qxp). In order to reach the maximum speed which is mentioned
in datasheet, the load of connect wires between master and slave
should be less than 15pF.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the default implementation of transfer_one_msg/chipselect/setup
functions in spi core to implement cs-gpio control.
Use fsl_lpspi_prepare_message to init the cs_gpio pin.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a error info when set a speed which greater than half of per-clk of
spi module.
The minimum SCK period is 2 cycles(CCR[SCKDIV]). So the maximum transfer
speed is half of spi per-clk.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable the runtime power management for lpspi module.
Do some adaptation work from kernel 4.9 to 4.14.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add both ipg and per clock for lpspi to support i.MX8QM/QXP boards.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds suspend and resume support for spi-stm32-qspi
drivers.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch solves a memory corruption seen at 8 MHz.
To avoid such issue, timeout counter is disabled.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While the sequencer is reset after each SPI message since commit
880c6d114f ("spi: rspi: Add support for Quad and Dual SPI
Transfers on QSPI"), it was never reset for the first message, thus
relying on reset state or bootloader settings.
Fix this by initializing it explicitly during configuration.
Fixes: 0b2182ddac ("spi: add support for Renesas RSPI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Renesas RSPI/QSPI driver performs SPI controller register
initialization in its spi_operations.setup() callback, without calling
pm_runtime_get_sync() first, which may cause spurious failures.
So far this went unnoticed, as this SPI controller is typically used
with a single SPI NOR FLASH containing the boot loader:
1. If the device's module clock is still enabled (left enabled by the
bootloader, and not yet disabled by the clk_disable_unused() late
initcall), register initialization succeeds,
2. If the device's module clock is disabled, register writes don't
seem to cause lock-ups or crashes.
Data received in the first SPI message may be corrupted, though.
Subsequent SPI messages seem to be OK.
E.g. on r8a7791/koelsch, one bit is lost while receiving the 6th
byte of the JEDEC ID for the s25fl512s FLASH, corrupting that byte
and all later bytes. But until commit a2126b0a01 ("mtd:
spi-nor: refine Spansion S25FL512S ID"), the 6th byte was not
considered for FLASH identification.
Fix this by moving all initialization from the .setup() to the
.prepare_message() callback. The latter is always called after the
device has been runtime-resumed by the SPI core.
This also makes the driver follow the rule that .setup() must not change
global driver state or register values, as that might break a transfer
in progress.
Fixes: 490c97747d ("spi: rspi: Add runtime PM support, using spi core auto_runtime_pm")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert points out that I confused the min/max arguments that are
reversed between SPI_BPW_RANGE_MASK() and GENMASK(). This time
I have verified the result of the macro after fixing the arguments.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: eefffb42f6 ("spi: work around clang bug in SPI_BPW_RANGE_MASK()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does not clearly unregister the spi controller.
Therefore calling an unbind and bind again will end up in a
Kernel crash.
The function devm_spi_register_controller will automatically
be unregister the SPI device.
Signed-off-by: Volker Haspel <volker.haspel@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 71abd29057 ("spi: imx: Add support for SPI Slave mode") added
an RX FIFO flush before start of a transfer. In slave mode, the master
may have sent more data than expected and this data will still be in the
RX FIFO at the start of the next transfer, and so needs to be flushed.
However, the code to do the flush was accidentally saving this data into
the previous transfer's RX buffer, clobbering the contents of whatever
followed that buffer.
Change it to empty the FIFO and throw away the data. Every one of the
RX functions for the different eCSPI versions and modes reads the RX
FIFO data using the same readl() call, so just use that, rather than
using the spi_imx->rx function pointer and making sure all the different
rx functions have a working "throw away" mode.
There is another issue, which affects master mode when switching from
DMA to PIO. There can be extra data in the RX FIFO which triggers this
flush code, causing memory corruption in the same manner. I don't know
why this data is unexpectedly in the FIFO. It's likely there is a
different bug or erratum responsible for that. But regardless of that,
I think this is proper fix the for bug at hand here.
Fixes: 71abd29057 ("spi: imx: Add support for SPI Slave mode")
Cc: Jiada Wang <jiada_wang@mentor.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the boolean module parameter "use_dma" to control the use of DMA by
the driver. There are about two dozen other drivers with a "use_dma"
parameter of some sort.
DMA may allow faster and more efficient transfers than using PIO, but it
also adds overhead for small transfers.
High speed receive operations may be less likely to have issues with
FIFO overflow when using DMA than when using PIO.
The eCSPI appears to insert a 4 bit pause after each word in DMA mode,
not done in PIO mode, which can make DMA transfers 50% slower than PIO.
In some cases DMA may be a net win while in others PIO might be. It
depends on the application. So allow DMA to be enabled or disabled at
the driver level. The default will be to have it enabled when possible.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang-8 evaluates both sides of a ?: expression to check for
valid arithmetic even in the side that is never taken. This
results in a build warning:
drivers/spi/spi-sh-msiof.c:1052:24: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
.bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32),
^~~~~~~~~~~~~~~~~~~~~~~~~
Change the implementation to use the GENMASK() macro that does
what we want here but does not have a problem with the shift
count overflow.
Link: https://bugs.llvm.org/show_bug.cgi?id=38789
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a bug for messages containing both zero length and
unidirectional xfers.
The function spi_map_msg will allocate dummy tx and/or rx buffers
for use with unidirectional transfers when the hardware can only do
a bidirectional transfer. That dummy buffer will be used in place
of a NULL buffer even when the xfer length is 0.
Then in the function __spi_map_msg, if he hardware can dma,
the zero length xfer will have spi_map_buf called on the dummy
buffer.
Eventually, __sg_alloc_table is called and returns -EINVAL
because nents == 0.
This fix prevents the error by not using the dummy buffer when
the xfer length is zero.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While the MSIOF variants in older SuperH and SH/R-Mobile SoCs support
bits-per-word values in the full range 8..32, the variants present in
R-Car Gen2 and Gen3 SoCs are restricted to 8, 16, 24, or 32.
Obtain the value from family-specific sh_msiof_chipdata to fix this.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
One more set of simple ARM platform fixes:
- A boot regression on qualcomm msm8998
- Gemini display controllers got turned off by accident
- incorrect reference counting in optee
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=doMO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"One more set of simple ARM platform fixes:
- A boot regression on qualcomm msm8998
- Gemini display controllers got turned off by accident
- incorrect reference counting in optee"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
tee: optee: add missing of_node_put after of_device_is_available
arm64: dts: qcom: msm8998: Extend TZ reserved memory area
ARM: dts: gemini: Re-enable display controller
Pull x86 fixes from Thomas Gleixner:
"Two last minute fixes:
- Prevent value evaluation via functions happening in the user access
enabled region of __put_user() (put another way: make sure to
evaluate the value to be stored in user space _before_ enabling
user space accesses)
- Correct the definition of a Hyper-V hypercall constant"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyper-v: Fix definition of HV_MAX_FLUSH_REP_COUNT
x86/uaccess: Don't leak the AC flag into __put_user() value evaluation
Nine small fixes. The resume fix is a cosmetic removal of a warning
with an incorrect condition causing it to alarm people wrongly. The
other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit
DMA masks meaning they bounce any page over 4GB before sending it to
the controller. Nowadays, even laptops mostly have memory above 4GB,
so this can lead to significant performance degradation with all the
bouncing.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHql8CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQmvAQCSVQRf
kx3ABDGnaj4Km4/Jzibj44aCYwh+ewwtLCWwFQD9GWaEaDxBkbxQDf/YndQKRhYg
VJQjjj6a9VlNSmWoW28=
=L9Fe
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes.
The resume fix is a cosmetic removal of a warning with an incorrect
condition causing it to alarm people wrongly.
The other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit DMA
masks meaning they bounce any page over 4GB before sending it to the
controller.
Nowadays, even laptops mostly have memory above 4GB, so this can lead
to significant performance degradation with all the bouncing"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Avoid that system resume triggers a kernel warning
scsi: hptiop: fix calls to dma_set_mask()
scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
scsi: csiostor: fix calls to dma_set_mask_and_coherent()
scsi: bfa: fix calls to dma_set_mask_and_coherent()
scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
scsi: lpfc: fix calls to dma_set_mask_and_coherent()
Pull networking fixes from David Miller:
1) Fix refcount leak in act_ipt during replace, from Davide Caratti.
2) Set task state properly in tun during blocking reads, from Timur
Celik.
3) Leaked reference in DSA, from Wen Yang.
4) NULL deref in act_tunnel_key, from Vlad Buslov.
5) cipso_v4_erro can reference the skb IPCB in inappropriate contexts
thus referencing garbage, from Nazarov Sergey.
6) Don't accept RTA_VIA and RTA_GATEWAY in contexts where those
attributes make no sense.
7) Fix hung sendto in tipc, from Tung Nguyen.
8) Out-of-bounds access in netlabel, from Paul Moore.
9) Grant reference leak in xen-netback, from Igor Druzhinin.
10) Fix tx stalls with lan743x, from Bryan Whitehead.
11) Fix interrupt storm with mv88e6xxx, from Hein Kallweit.
12) Memory leak in sit on device registry failure, from Mao Wenan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: sit: fix memory leak in sit_init_net()
net: dsa: mv88e6xxx: Fix statistics on mv88e6161
geneve: correctly handle ipv6.disable module parameter
net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode
bpf: fix sanitation rewrite in case of non-pointers
ipv4: Add ICMPv6 support when parse route ipproto
MIPS: eBPF: Fix icache flush end address
lan743x: Fix TX Stall Issue
net: phy: phylink: fix uninitialized variable in phylink_get_mac_state
net: aquantia: regression on cpus with high cores: set mode with 8 queues
selftests: fixes for UDP GRO
bpf: drop refcount if bpf_map_new_fd() fails in map_create()
net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X
net: dsa: mv88e6xxx: Fix u64 statistics
xen-netback: don't populate the hash cache on XenBus disconnect
xen-netback: fix occasional leak of grant ref mappings under memory pressure
sctp: chunk.c: correct format string for size_t in printk
net: netem: fix skb length BUG_ON in __skb_to_sgvec
netlabel: fix out-of-bounds memory accesses
ipv4: Pass original device to ip_rcv_finish_core
...
Pull more crypto fixes from Herbert Xu:
"This fixes a couple of issues in arm64/chacha that was introduced in
5.0"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/chacha - fix hchacha_block_neon() for big endian
crypto: arm64/chacha - fix chacha_4block_xor_neon() for big endian
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.
Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c3949 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPv6 is compiled but disabled at runtime, geneve_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.
Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.
This is the same fix as what commit d074bf9600 ("vxlan: correctly handle
ipv6.disable module parameter") is doing for vxlan.
Note there's also commit c0a47e44c0 ("geneve: should not call rt6_lookup()
when ipv6 was disabled") which fixes a similar issue but for regular
tunnels, while this patch is needed for metadata based tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-03-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix sanitation rewrite, from Daniel.
2) fix error path on map_new_fd, from Peng.
3) fix icache flush address, from Paul.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek reported that he saw an issue with the below snippet in that
timing measurements where off when loaded as unpriv while results
were reasonable when loaded as privileged:
[...]
uint64_t a = bpf_ktime_get_ns();
uint64_t b = bpf_ktime_get_ns();
uint64_t delta = b - a;
if ((int64_t)delta > 0) {
[...]
Turns out there is a bug where a corner case is missing in the fix
d3bd7413e0 ("bpf: fix sanitation of alu op with pointer / scalar
type from different paths"), namely fixup_bpf_calls() only checks
whether aux has a non-zero alu_state, but it also needs to test for
the case of BPF_ALU_NON_POINTER since in both occasions we need to
skip the masking rewrite (as there is nothing to mask).
Fixes: d3bd7413e0 ("bpf: fix sanitation of alu op with pointer / scalar type from different paths")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Reported-by: Arthur Fabre <afabre@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/netdev/CAJPywTJqP34cK20iLM5YmUMz9KXQOdu1-+BZrGMAGgLuBWz7fg@mail.gmail.com/T/
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.
Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.
v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: eacb9384a3 ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MIPS eBPF JIT calls flush_icache_range() in order to ensure the
icache observes the code that we just wrote. Unfortunately it gets the
end address calculation wrong due to some bad pointer arithmetic.
The struct jit_ctx target field is of type pointer to u32, and as such
adding one to it will increment the address being pointed to by 4 bytes.
Therefore in order to find the address of the end of the code we simply
need to add the number of 4 byte instructions emitted, but we mistakenly
add the number of instructions multiplied by 4. This results in the call
to flush_icache_range() operating on a memory region 4x larger than
intended, which is always wasteful and can cause crashes if we overrun
into an unmapped page.
Fix this by correcting the pointer arithmetic to remove the bogus
multiplication, and use braces to remove the need for a set of brackets
whilst also making it obvious that the target field is a pointer.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9c4 ("MIPS: Add missing file for eBPF JIT.")
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.
This fix corrects the problem by properly marking the end of
a multi descriptor transmission.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the maximum number of queues was increased up to 8, but
NIC was not fully configured for 8 queues. In setups with more than 4 CPU
cores parts of TX traffic gets lost if the kernel routes it to queues 4th-8th.
This patch sets a tx hw traffic mode with 8 queues.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202651
Fixes: 71a963cfc5 ("net: aquantia: increase max number of hw queues")
Reported-by: Nicholas Johnson <nicholas.johnson@outlook.com.au>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation for UDP GRO tests is racy: the receiver
may flush the RX queue while the sending is still transmitting and
incorrectly report RX errors, with a wrong number of packet received.
Add explicit timeouts to the receiver for both connection activation
(first packet received for UDP) and reception completion, so that
in the above critical scenario the receiver will wait for the
transfer completion.
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One important patch:
- Fix for a memory corruption issue in the Intel VT-d driver
that triggers on hardware with deep PCI hierarchies
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=H9KF
-----END PGP SIGNATURE-----
Merge tag 'iommu-fix-v5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"One important fix for a memory corruption issue in the Intel VT-d
driver that triggers on hardware with deep PCI hierarchies"
* tag 'iommu-fix-v5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dmar: Fix buffer overflow during PCI bus notification
Merge misc fixes from Andrew Morton:
"2 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
hugetlbfs: fix races and page leaks during migration
kasan: turn off asan-stack for clang-8 and earlier
hugetlb pages should only be migrated if they are 'active'. The
routines set/clear_page_huge_active() modify the active state of hugetlb
pages.
When a new hugetlb page is allocated at fault time, set_page_huge_active
is called before the page is locked. Therefore, another thread could
race and migrate the page while it is being added to page table by the
fault code. This race is somewhat hard to trigger, but can be seen by
strategically adding udelay to simulate worst case scheduling behavior.
Depending on 'how' the code races, various BUG()s could be triggered.
To address this issue, simply delay the set_page_huge_active call until
after the page is successfully added to the page table.
Hugetlb pages can also be leaked at migration time if the pages are
associated with a file in an explicitly mounted hugetlbfs filesystem.
For example, consider a two node system with 4GB worth of huge pages
available. A program mmaps a 2G file in a hugetlbfs filesystem. It
then migrates the pages associated with the file from one node to
another. When the program exits, huge page counts are as follows:
node0
1024 free_hugepages
1024 nr_hugepages
node1
0 free_hugepages
1024 nr_hugepages
Filesystem Size Used Avail Use% Mounted on
nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool
That is as expected. 2G of huge pages are taken from the free_hugepages
counts, and 2G is the size of the file in the explicitly mounted
filesystem. If the file is then removed, the counts become:
node0
1024 free_hugepages
1024 nr_hugepages
node1
1024 free_hugepages
1024 nr_hugepages
Filesystem Size Used Avail Use% Mounted on
nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool
Note that the filesystem still shows 2G of pages used, while there
actually are no huge pages in use. The only way to 'fix' the filesystem
accounting is to unmount the filesystem
If a hugetlb page is associated with an explicitly mounted filesystem,
this information in contained in the page_private field. At migration
time, this information is not preserved. To fix, simply transfer
page_private from old to new page at migration time if necessary.
There is a related race with removing a huge page from a file and
migration. When a huge page is removed from the pagecache, the
page_mapping() field is cleared, yet page_private remains set until the
page is actually freed by free_huge_page(). A page could be migrated
while in this state. However, since page_mapping() is not set the
hugetlbfs specific routine to transfer page_private is not called and we
leak the page count in the filesystem.
To fix that, check for this condition before migrating a huge page. If
the condition is detected, return EBUSY for the page.
Link: http://lkml.kernel.org/r/74510272-7319-7372-9ea6-ec914734c179@oracle.com
Link: http://lkml.kernel.org/r/20190212221400.3512-1-mike.kravetz@oracle.com
Fixes: bcc5422230 ("mm: hugetlb: introduce page_huge_active")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: <stable@vger.kernel.org>
[mike.kravetz@oracle.com: v2]
Link: http://lkml.kernel.org/r/7534d322-d782-8ac6-1c8d-a8dc380eb3ab@oracle.com
[mike.kravetz@oracle.com: update comment and changelog]
Link: http://lkml.kernel.org/r/420bcfd6-158b-38e4-98da-26d0cd85bd01@oracle.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building an arm64 allmodconfig kernel with clang results in over 140
warnings about overly large stack frames, the worst ones being:
drivers/gpu/drm/panel/panel-sitronix-st7789v.c:196:12: error: stack frame size of 20224 bytes in function 'st7789v_prepare'
drivers/video/fbdev/omap2/omapfb/displays/panel-tpo-td028ttec1.c:196:12: error: stack frame size of 13120 bytes in function 'td028ttec1_panel_enable'
drivers/usb/host/max3421-hcd.c:1395:1: error: stack frame size of 10048 bytes in function 'max3421_spi_thread'
drivers/net/wan/slic_ds26522.c:209:12: error: stack frame size of 9664 bytes in function 'slic_ds26522_probe'
drivers/crypto/ccp/ccp-ops.c:2434:5: error: stack frame size of 8832 bytes in function 'ccp_run_cmd'
drivers/media/dvb-frontends/stv0367.c:1005:12: error: stack frame size of 7840 bytes in function 'stv0367ter_algo'
None of these happen with gcc today, and almost all of these are the
result of a single known issue in llvm. Hopefully it will eventually
get fixed with the clang-9 release.
In the meantime, the best idea I have is to turn off asan-stack for
clang-8 and earlier, so we can produce a kernel that is safe to run.
I have posted three patches that address the frame overflow warnings
that are not addressed by turning off asan-stack, so in combination with
this change, we get much closer to a clean allmodconfig build, which in
turn is necessary to do meaningful build regression testing.
It is still possible to turn on the CONFIG_ASAN_STACK option on all
versions of clang, and it's always enabled for gcc, but when
CONFIG_COMPILE_TEST is set, the option remains invisible, so
allmodconfig and randconfig builds (which are normally done with a
forced CONFIG_COMPILE_TEST) will still result in a mostly clean build.
Link: http://lkml.kernel.org/r/20190222222950.3997333-1-arnd@arndb.de
Link: https://bugs.llvm.org/show_bug.cgi?id=38809
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Qian Cai <cai@lca.pw>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=TtJZ
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-03-01' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Three final fixes, one for a feature that is new in this kernel, one
bochs fix for qemu riscv and one atomic modesetting fix.
I've left a few of the other late fixes until next as I didn't want to
throw in anything that wasn't really necessary"
* tag 'drm-fixes-2019-03-01' of git://anongit.freedesktop.org/drm/drm:
drm/bochs: Fix the ID mismatch error
drm: Block fb changes for async plane updates
drm/amd/display: Use vrr friendly pageflip throttling in DC.
In bpf/syscall.c, map_create() first set map->usercnt to 1, a file
descriptor is supposed to return to userspace. When bpf_map_new_fd()
fails, drop the refcount.
Fixes: bd5f5f4ecb ("bpf: Add BPF_MAP_GET_FD_BY_ID")
Signed-off-by: Peng Sun <sironhide0null@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
- Fix 16b cmpxchg() operations which could erroneously fail if bits 15:8
of the old value are non-zero. In practice I'm not aware of any actual
users of 16b cmpxchg() on MIPS, but this fixes the support for it was
was introduced in v4.13.
- Provide a struct device to dma_alloc_coherent for Lantiq XWAY systems
with a "Voice MIPS Macro Core" (VMMC) device.
- Provide DMA masks for BCM63xx ethernet devices, fixing a regression
introduced in v4.19.
- Fix memblock reservation for the kernel when the system has a non-zero
PHYS_OFFSET, correcting the memblock conversion performed in v4.20.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXHhqjBUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN3ZaAD/SFgi3dS9bSWhDhiy83llLaWiCGPb
i09uzo3rpWoKSwQBAIwLEfmaHz/sYdliKRlE13uaxYWzwaN+VHXIPjlzbYMB
=cDlO
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.0_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few more MIPS fixes:
- Fix 16b cmpxchg() operations which could erroneously fail if bits
15:8 of the old value are non-zero. In practice I'm not aware of
any actual users of 16b cmpxchg() on MIPS, but this fixes the
support for it was was introduced in v4.13.
- Provide a struct device to dma_alloc_coherent for Lantiq XWAY
systems with a "Voice MIPS Macro Core" (VMMC) device.
- Provide DMA masks for BCM63xx ethernet devices, fixing a regression
introduced in v4.19.
- Fix memblock reservation for the kernel when the system has a
non-zero PHYS_OFFSET, correcting the memblock conversion performed
in v4.20"
* tag 'mips_fixes_5.0_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: fix memory setup for platforms with PHYS_OFFSET != 0
MIPS: BCM63XX: provide DMA masks for ethernet devices
MIPS: lantiq: pass struct device to DMA API functions
MIPS: fix truncation in __cmpxchg_small for short values
Jan Kundrát