This patch uses xhci_plat_priv.quirks to simplify. The previous
code had conditions to set some quirks in xhci_rcar_init_quirk().
But, the xhci_rcar_init_quirk() is called at the same conditions.
So, no behavior change.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1567425698-27560-4-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's spelled "renesas", not "renensas".
Due to this typo, RZ/G1M and RZ/G1N were not covered by the check.
Fixes: 2dc240a330 ("usb: host: xhci: rcar: retire use of xhci_plat_type_is()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20190827125112.12192-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is connected to the host controller and
the system enters suspend, the following error happens
in xhci_suspend():
xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout
Since the firmware/internal CPU control the USBSTS.STS_HALT
and the process speed is down when the roothub port enters U3,
long delay for the handshake of STS_HALT is neeed in xhci_suspend().
So, this patch adds to set the XHCI_SLOW_SUSPEND.
Fixes: 435cc1138e ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a condition check about the PLL acvice of this
controller. Otherwise, the controller might cause hang when
any USB clocks are not supplied yet and accesses the xHCI registers.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies getting the firmware name for R-Car Gen3.
Almost all R-Car Gen3 USB3.0 Host controllers use "V3". But,
r8a7795 ES1.x SoCs only should use "V2". Since the xhci-plat already
has the firmware_name of R-Car Gen3 as "V3", the xhci-rcar doesn't
need some members of rcar_quirks_match.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car H3 ES2.0. Since this SoC revision
(or later) should use the V3 firmware, the driver needs to check
the revision via soc_device_match().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds firmware_name selection by soc_device_match() to
use other firmware name in the future. (For now, using the firmware
is the same as before.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets resume_quirk() for R-Car controllers to re-download
the firmware in resume timing. Otherwise, if the controller's power
is down in suspend timing, the firmware in the controller goes away,
and then the controller doesn't work after resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for Renesas r8a7796 SoC. This SoC is not
compatible with r8a7795 because using firmware version differs.
Since the "V2" firmware can be used on both r8a7795 (es1.x) and r8a7796,
the "renesas,rcar-gen3-xhci" keeps to use the "V2" for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new firmware version "V3" for r8a7796. This patch
also adds explanation of each version's information.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're preparing to remove xhci_plat_type_is() in
favor of a better approach where we define function
pointers ahead of time. This will let us make
assumptions about which platforms we're running on
and which platform-specific functions we should call.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[delete extra comma in function parameters -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The R-Car H3 has two xHCI controllers. This SoC is compatible with
R-Car Gen2 SoCs, however this SoC doesn't need some specific registers
setting, and need a new firmware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes code to ease the addition of next generation SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The R-Car H2 and M2 SoCs come with an xHCI controller that requires
some specific initializations related to the firmware downloading and
some specific registers. This patch adds the support for this special
configuration as an xHCI quirk executed during probe and start.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: "mathias.nyman@intel.com" <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun