Commit Graph

5152 Commits

Author SHA1 Message Date
Maxime Ripard 16e821e3ba mmc: sunxi: Mask DATA0 when updating the clock
The A64 MMC controllers need DATA0 to be masked while updating the clock,
otherwise any subsequent command will result in a timeout.

It's not really clear at this point what DATA0 is exactly, but this
behaviour is present in Allwinner's tree, and has been suggested by
Allwinner engineers as fixes for the timeout.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:51 +01:00
Maxime Ripard 9a37e53e45 mmc: sunxi: Enable the new timings for the A64 MMC controllers
The A64 MMC controllers need to set a "new timings" bit when a new rate is
set.

The actual meaning of that bit is not clear yet, but not setting it leads
to some corner-case issues, like the CMD53 failing, which is used to
implement SDIO packet aggregation.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:50 +01:00
Maxime Ripard 860fdf89b9 mmc: sunxi: Always set signal delay to 0 for A64
Experience have shown that the using the  autocalibration could severely
degrade the performances of the MMC bus.

Allwinner is using in its BSP a delay set to 0 for all the modes but HS400.
Remove the calibration code for now, and add comments to document our
findings.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:49 +01:00
Maxime Ripard 9479074e93 mmc: sunxi: Gate the clock when rate is 0
The MMC core assumes that the code will gate the clock when the bus
frequency is set to 0, which we've been ignoring so far.

Handle that.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:49 +01:00
Maxime Ripard 39cc281fb7 mmc: sunxi: Fix clock frequency change sequence
The SD specification documents that the clock frequency should only be
changed once gated (Section 3.2.3 - SD Clock Frequency Change Sequence).

The current code first modifies the parent clock, gates it and then
modifies the internal divider. This means that since the parent clock rate
might be changed, the bus clock might be changed as well before it is
gated, which breaks the specification.

Move the gating before the parent rate modification.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:48 +01:00
Heiner Kallweit 1ed2171944 mmc: core: fix error path in mmc_host_alloc
Properly reverse everything if mmc_gpio_alloc(host) fails.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:48 +01:00
Heiner Kallweit 7413d1f509 mmc: core: simplify ida handling
ida handling can be simplified by switching to the ida_simple_
functions.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:47 +01:00
Ritesh Harjani 543c576d1b mmc: sdhci-msm: Remove unnecessary comments of CDC init sequence
This removes CDC init sequence comments which are
not useful anyway.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:46 +01:00
Ritesh Harjani 4436c53599 mmc: sdhci-msm: Remove platform_execute_tuning from sdhci_msm_ops
platform_execute_tuning should not really exist as it does not
do anything useful.

So remove this ops and directly plug sdhci_msm_execute_tuning
with mmc_host_ops.

Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once
HS400 related mode selection is done.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:46 +01:00
Ulf Hansson fb00f196fc mmc: core: Extend mmc_of_parse() to check for mmc-ddr-3_3v
When mmc_of_parse() finds the binding, it sets the mmc cap,
MMC_CAP_3_3V_DDR, which informs the core whether eMMC DDR at 3.3V I/O is
supported by the mmc host.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-02-13 13:20:45 +01:00
Ulf Hansson 20f921bb01 mmc: core: Invent MMC_CAP_3_3V_DDR
According the JEDEC specification an eMMC card supporting 1.8V vccq in DDR
mode should also be capable of 3.3V. However, it's been reported that some
mmc hosts supports 3.3V, but not 1.8V.

Currently the mmc core implements an error handling when the host fails to
set 1.8V for vccq, by falling back to 3.3V. Unfortunate, this seems to be
insufficient for some mmc hosts. To enable these to use eMMC DDR mode let's
invent a new mmc cap, MMC_CAP_3_3V_DDR, which tells whether they support
the eMMC 3.3V DDR mode.

In case MMC_CAP_3_3V_DDR is set, but not MMC_CAP_1_8V_DDR, let's change to
remain on the 3.3V, as it's the default voltage level for vccq, set by the
earlier power up sequence.

As this change introduces MMC_CAP_3_3V_DDR, let's take the opportunity to
do some re-formatting of the related defines in the header file.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-02-13 13:20:44 +01:00
Ulf Hansson 4e74b6b3c6 mmc: core: Rename __mmc_set_signal_voltage() to mmc_set_signal_voltage()
Earlier the mmc_set_signal_voltage() existed, but since it has been renamed
to mmc_set_uhs_voltage(), we can now use that name instead.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-02-13 13:20:43 +01:00
Ulf Hansson 2ed573b603 mmc: core: Clarify usage of mmc_set_signal_voltage()
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. To clarify this let's do the following changes.

- We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage
  parameter to the function. Then, let's just remove the parameter as it
  serves no purpose.
- Rename the function to mmc_set_uhs_voltage().

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-02-13 13:20:43 +01:00
Ulf Hansson a44efa4796 mmc: core: Remove redundant code in mmc_set_signal_voltage()
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. Therefore let's remove the redundant code dealing with
MMC_SIGNAL_VOLTAGE_330.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-02-13 13:20:42 +01:00
Chris Brandt 34a1654706 mmc: sh_mobile_sdhi: add support for 2 clocks
Some controllers have 2 clock sources instead of 1. The 2nd clock
is for the internal card detect logic and must be enabled/disabled
along with the main core clock for proper operation.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
2017-02-13 13:20:41 +01:00
Kevin Hilman dc012058d7 mmc: meson: cleanup stray debug messages
Cleanup some debug prints that cause needless noise
during normal usage.

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:40 +01:00
Linus Walleij df06158896 mmc: block: stop passing around pointless return values
The mmc_blk_issue_rq() function is called in exactly one place
in queue.c and there the return value is ignored. So the
functions called from that function that also meticulously
return 0/1 do so for no good reason.

Error reporting on the asynchronous requests are done upward to
the block layer when the requests are eventually completed or
fail, which may happen during the flow of the mmc_blk_issue_*
functions directly (for "special commands") or later, when an
asynchronous read/write request is completed.

The issuing functions do not give rise to errors on their own,
and there is nothing to return back to the caller in queue.c.
Drop all return values and make the function return void.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:40 +01:00
Linus Walleij 7d552a4808 mmc: block: introduce new_areq and old_areq
Recycling the same variable in an x=x+1 fashion may seem
clever here but it makes the code terse and hard to follow
for humans. Introduce a new_areq and old_areq variable so
we see what is going on.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:39 +01:00
Linus Walleij da0dbaffe3 mmc: block: inline command abortions
Setting rqc to NULL followed by a goto to cmd_abort is just a way
to do unconditional abort without starting any new command.
Inline the calls to mmc_blk_rw_cmd_abort() and return immediately
in those cases.

Add some comments to the code flow so it is clear that this is
where the asynchronous requests come back in and the result of
them gets handled.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:39 +01:00
Linus Walleij 6fb85d6583 mmc: block: do not assign mq_rq when aborting command
The code in mmc_blk_issue_rq_rq() aborts a command if the request
is not properly aligned on large sectors. As part of the path
jumping out, it assigns the local variable mq_rq reflecting
a MMC queue request to the current MMC queue request, which is
confusing since the variable is not used after this jump.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:38 +01:00
Linus Walleij efb5a05e70 mmc: block: break out mmc_blk_rw_start_new()
As a step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the code to start a new
request.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:38 +01:00
Linus Walleij 4e1f780032 mmc: block: break out mmc_blk_rw_cmd_abort()
As a first step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the command abort code.
This code assumes "ret" is != 0 and then repeatedly hammers
blk_end_request() until the request to the block layer to end
the request succeeds.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:37 +01:00
Jaehoon Chung e64aae82ea mmc: sdhci-s3c: use the bitops API for bit operation
Use the bitops API instead of shifting directly.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:36 +01:00
Jaehoon Chung 57f8324501 mmc: sdhci-s3c: remove the sdhci-s3c-regs header file
Remove the sdhci-s3c-regs.h file.
Instead, it located those defined values into sdhci-s3c.c.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:36 +01:00
Wolfram Sang ee28981535 mmc: tmio: discard obsolete SDIO irqs before enabling irqs
Before enabling SDIO irqs, clear the status bit, so we discard old and
stale interrupts. Needed to get two wireless cards working. Use the
newly introduced macro in all places.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:35 +01:00
Wolfram Sang 20dd03734c mmc: host: tmio: SDIO_STATUS_QUIRK is rather SDIO_STATUS_SETBITS
QUIRK sounds like there is something wrong, but actually there are just
some bits which need to be 1. Rename it to be more clear.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:34 +01:00
Wolfram Sang e4f38eb18a mmc: host: tmio: refactor calls to sdio irq
tmio_mmc_sdio_irq() is not used as a seperate irq handler anymore, so we
can make it similar to the other irq helper functions, namely:

* only give the host as argument function which is what it really needs
* prefix function name with __

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:34 +01:00
Matt Ranostay de19b4c928 mmc: pwrseq: add support for Marvell SD8787 chip
Allow power sequencing for the Marvell SD8787 Wifi/BT chip.
This can be abstracted to other chipsets if needed in the future.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:33 +01:00
Wolfram Sang dfcba5ffca mmc: host: tmio: disable clocks when unbinding
Create a helper function to disable clocks and use it in remove(), too.
Now, clk_summary in debugfs reports the clocks as disabled and
unprepared after unbinding.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:32 +01:00
Ritesh Harjani 44bf23128f mmc: sdhci-msm: Provide enhanced_strobe mode feature support
This provides enhanced_strobe mode feature support in sdhci-msm
driver.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:31 +01:00
Ritesh Harjani d7507aa1b9 mmc: sdhci-msm: Make HS400 tuning follow as per recommeneded HW sequence
During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:31 +01:00
Ritesh Harjani 8a8fa8797c mmc: sdhci: Clear SDHCI_HS400_TUNING flag after platform_execute_tuning
Clear SDHCI_HS400_TUNING flag after platform_execute_tuning
so that platform_execute_tuning may use it if needed.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:30 +01:00
Subhash Jadavani 083c9aa0ad mmc: sdhci-msm: configure CORE_CSR_CDC_DELAY_CFG to recommended value
Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.

Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:30 +01:00
Venkat Gopalakrishnan 5574ddcc60 mmc: sdhci-msm: Reset vendor specific func register on probe
The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:29 +01:00
Ritesh Harjani db9bd16381 mmc: sdhci-msm: Factor out sdhci_msm_hs400
Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:29 +01:00
Ritesh Harjani 0fb8a3d46b mmc: sdhci-msm: Factor out function to set/get msm clock rate
Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:28 +01:00
Ritesh Harjani b54aaa8a4f mmc: sdhci-msm: Factor out sdhci_msm_hc_select_mode
This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:27 +01:00
Stefan Wahren 73a85069f9 mmc: mxs-mmc: Implement CMD23 support
This patch implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23) on the MXS MMC host driver.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:27 +01:00
Alexey Khoroshilov e81c022a00 mmc: wbsd: safer check if dma_addr is valid DMA address
host->dma_addr can store a value that is not returned by the DMA API,
so it is safer to check if is a valid DMA address indirectly.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:26 +01:00
Zhang Rui e28d6f0487 mmc: sdhci-acpi: support deferred probe
With commit 67bf5156ed ("gpio / ACPI: fix returned error from
acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if
GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver
should be probed again later in this case.

This fixes an order issue when both GPIO and sdhci-acpi drivers are built
as modules.

CC: stable@vger.kernel.org # v4.9
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177101
Tested-by: Jonas Aaberg <cja@gmx.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:26 +01:00
Ulf Hansson 5857b29b96 mmc: core: Move public functions from host.h to private headers
A significant amount of functions are available through the public mmc
host.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc host.h header file.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-02-13 13:20:25 +01:00
Ulf Hansson 4facdde113 mmc: core: Move public functions from card.h to private headers
A significant amount of functions and other definitions are available
through the public mmc card.h header file. Let's slim down this public mmc
interface, as to prevent users from abusing it, by moving some of the
functions/definitions to private mmc header files.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-02-13 13:20:24 +01:00
Ulf Hansson 2e4af7b655 mmc: vub300: Don't use mmc_card_present() when validating for inserted card
The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:20:23 +01:00
Ulf Hansson 136b0a471c mmc: omap: Don't use mmc_card_present() when validating for inserted card
The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.

Cc: linux-omap@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:20:23 +01:00
Ulf Hansson 55244c5659 mmc: core: Move public functions from core.h to private headers
A significant amount of functions are available through the public mmc
core.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc header files.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups, as an example
some functions can be turned into static.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-02-13 13:20:21 +01:00
Ulf Hansson 066185d690 mmc: core: First step in cleaning up private mmc header files
This is the first step in cleaning up the private mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.

While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-02-13 13:20:20 +01:00
Arnd Bergmann e1c6ec26b8 mmc: s3cmci: include linux/interrupt.h for tasklet_struct
I got this new build error on today's linux-next

drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
  struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]

While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:19 +01:00
Ulf Hansson efd7be7bfc mmc: tmio: Remove redundant check of mmc->slot.cd_irq
To validate whether native hotplug needs to be used, the tmio driver checks
whether the mmc->slot.cd_irq has been successfully assigned.

This check is redundant at its current place in tmio_mmc_host_probe(), as
the mmc core assigns mmc->slot.cd_irq a valid value first when
mmc_gpiod_request_cd_irq() is called. Therefore, let's just remove the
check for now, as that also removes a layering violation of the tmio driver
accessing core specific data via ->slot.cd_irq.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
2017-02-13 13:20:15 +01:00
yangbo lu e87d2db2a2 mmc: sdhci-of-esdhc: avoid clock glitch when frequency is changing
The eSDHC_PRSSTAT[SDSTB] bit indicates whether the internal card clock is
stable. This bit is for the host driver to poll clock status when changing
the clock frequency. It is recommended to clear eSDHC_SYSCTL[SDCLKEN]
to remove glitch on the card clock when the frequency is changing. This
patch is to disable SDCLKEN bit before changing frequency and enable it
after SDSTB bit is set.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:15 +01:00
Shyam Sundar S K c31165d740 mmc: sdhci-pci: Add support for HS200 tuning mode on AMD, eMMC-4.5.1
This patch adds support for HS200 tuning mode on AMD eMMC-4.5.1

Reviewed-by: Sen, Pankaj <Pankaj.Sen@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Agrawal, Nitesh-kumar <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:14 +01:00
Shawn Lin dc0f585e83 mmc: vub300: Remove bogus check of irqs_queued
It's unnecessary to check the irqs_queued value as
it always needs to queue one if irq isn't enabled.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:13 +01:00
Shawn Lin 5fc3d80ef4 mmc: sdio: don't use rocr to check if the card could support UHS mode
Per SDIO Simplified Specification V3, section 3.1.2, A host that
supports UHS-I sets S18R to 1 in the argument of CMD5 to request a
change of the signal voltage to 1.8V. If the card supports UHS-I and
the current signal voltage is 3.3V, S18A is set to 1 in the R4 response.
If the signal voltage is already 1.8V, the card sets S18A to 0 so that
host maintains the current signal voltage. UHS-I is supported in SD mode
and S18A is always 0 in SPI mode.

For the current code, if the signaling voltage is fixed 1.8v, so
the card will set S18A to 0 for rocr and thus we would clear the
R4_18V_PRESENT from ocr, which make core won't try to use uhs mode.

To fix it, we expect sdio_read_cccr would fail if the uhs mode won't
work at all. Note that it's interesting that some sdio cards still
response S18A even the voltage is fixed to 1.8v and the CMD11 will
also accepted and finish enabling UHS mode successfully. I guess this
is why folks didn't notice this problem. Anyway, fix it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:13 +01:00
Shawn Lin 0eb51a58ad mmc: sdio: Factor out retry init card helper function
Add new helper function, mmc_sdio_resend_if_cond, to be
reused when trying to retry the init sequence.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:12 +01:00
Markus Elfring 63928d4789 mmc: core: Use kmalloc_array() in mmc_alloc_sg()
* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:11 +01:00
Markus Elfring 3972a20b51 mmc: mmc_test: Use kcalloc() in mmc_test_alloc_mem()
* The script "checkpatch.pl" pointed information out like the following.

  WARNING: Prefer kcalloc over kzalloc with multiply

  Thus fix the affected source code place.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:11 +01:00
Markus Elfring 554d7c540e mmc: mmc_test: Improve a size determination in five functions
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:10 +01:00
Markus Elfring 7200449dc6 mmc: mmc_test: Combine substrings for 5 messages
The script "checkpatch.pl" pointed information out like the following.

WARNING: quoted string split across lines

Thus fix affected source code places.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:10 +01:00
Markus Elfring fda02ea814 mmc: mmc_test: Add some spaces for better code readability
Use space characters at some source code places according to
the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:09 +01:00
Markus Elfring dc3a5fe6ec mmc: mmc_test: Use seq_puts() in mtf_testlist_show()
The script "checkpatch.pl" pointed information out like the following.

WARNING: Prefer seq_puts to seq_printf

Thus fix the affected source code place.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:08 +01:00
Markus Elfring 74536bc083 mmc: mmc_test: Fix a typo in a comment line
Add a missing character in the function description.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:08 +01:00
Markus Elfring 457e4f7f66 mmc: mmc_test: Use kmalloc_array() in mmc_test_area_init()
* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:07 +01:00
Wolfram Sang ad7014b394 mmc: host: tmio: drop superfluous exit path
The probe exit path on error does nothing since commit 94b110aff8
("mmc: tmio: add tmio_mmc_host_alloc/free()"), so we can bail out
immediately.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:07 +01:00
Andy Shevchenko c1ada71fb7 mmc: slot-gpio: Don't override con_id when request descriptor
The caller may supply connection ID, index, or both. All combinations are
possible and mmc framework should not make any assumption on what exactly
caller wants.

Remove con_id override conditionals in mmc_gpiod_request_ro() and
mmc_gpiod_request_cd().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:06 +01:00
Andy Shevchenko 6ac9b83772 mmc: sdhci-pci: Remove unused member cd_con_id
cd_con_id is not used and always NULL.
Remove it to make code a bit more cleaner.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:06 +01:00
yong mao 3bc702ed21 mmc: mediatek: correct the implementation of msdc_card_busy
msdc_card_busy only need check if the data0 is low.
In sdio data1 irq mode, data1 may be low because of interruption.

Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:05 +01:00
yangbo lu e9acc77dd0 mmc: sdhci-of-esdhc: remove default broken-cd for ARM
Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:04 +01:00
yangbo lu a6b448884a mmc: sdhci-esdhc: clean up register definitions
The eSDHC register definitions in header file were messy and confusing.
This patch is to clean up these definitions.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:04 +01:00
Jun Nie a8c643ad00 mmc: dw_mmc: zx: Initial support for ZX mmc controller
This platform driver adds initial support for the DW host controller
found on ZTE SoCs.

It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:03 +01:00
Jun Nie d6fced8337 mmc: dw_mmc: Add fifo watermark alignment property
Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested
to be aligned with data length in some SoC so that TX/RX
irq can be generated with data done irq. Add the
watermark alignment to mark this requirement and force
fifo watermark setting accordingly.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:02 +01:00
Jun Nie a0361c1a4d mmc: dw_mmc: Add fifo address property
The FIFO address may break default address assumption of 0x100
(version < 0x240A) and 0x200(version >= 0x240A) in current driver.
The new property is introduced to override fifo address via DT
node information.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:02 +01:00
Ulf Hansson b8789ec482 mmc: host: Include interrupt.h in mmc host drivers that depends on it
An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:20:01 +01:00
Ulf Hansson 210583f472 mmc: sdhci: Include leds.h
Don't rely on host.h to include the leds.h header, but instead include it
explicitly because the driver depends on it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2017-02-13 13:20:00 +01:00
Ulf Hansson 963836ad8f mmc: sdhci-cadence: Include mmc.h
Don't rely on host.h to include the mmc.h header, but instead include it
explicitly because the driver depends on it.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2017-02-13 13:19:59 +01:00
Ulf Hansson 0f21c58c63 mmc: dw_mmc: Remove the public dw_mmc header file
There are currently no external users of the public dw_mmc header file,
except the dw_mmc driver itself. Therefore let's move the definitions from
the public dw_mmc header file into the existing private dw_mmc header file
and then remove the public one.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:19:59 +01:00
Ulf Hansson dba4bb484e mmc: sh_mmcif: Remove unused clk_ctrl2_present from the platform data
There are currently no users of the clk_ctrl2_present member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may support clk_ctrl2, let's keep
the current code in the driver, which deals with this. For future support,
we should invent a DT binding instead, but let's leave that until it's
needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:19:58 +01:00
Ulf Hansson 8020f71117 mmc: sh_mmcif: Remove unused ccs_unsupported from the platform data
There are currently no users of the ccs_unsupported member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may not support ccs, let's keep the
current code in the driver, which deals with this. For future support, we
should invent a DT binding instead, but let's leave that until it's needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:19:58 +01:00
Ulf Hansson 5957eeba53 mmc: sh_mmcif: Remove unused ->get_cd() platform callback
Removing the callback also enables us to remove the sh_mmcif_get_cd()
altogether, as we convert to use mmc_gpio_get_cd() to the same kind of
work.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:57 +01:00
Ulf Hansson 95cc4df716 mmc: sh_mmcif: Remove unused use_cd_gpio/cd_gpio from platform data
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:19:57 +01:00
Stefan Wahren 40165de23d mmc: sdhci-iproc: Increase max_blk_size for bcm2835
According to the BCM2835 datasheet the maximum block size for the
eMMC module is restricted to the internal data FIFO which is 1024 byte.
But this is still an improvement to the default of 512 byte.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:55 +01:00
Stefan Wahren c82c277543 mmc: sdhci-iproc: Apply caps from bcm2835-mmc driver
Since the mmc module on bcm2835 neither provide a capabilities register nor
free documentation we must rely on the downstream implementation [1].

So enable the following capabilities for bcm2835:

MMC_CAP_MMC_HIGHSPEED
MMC_CAP_SD_HIGHSPEED
MMC_CAP_DRIVER_TYPE_A
MMC_CAP_DRIVER_TYPE_C

[1] - https://github.com/raspberrypi/linux/blob/rpi-4.4.y/drivers/mmc/host/bcm2835-mmc.c

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:54 +01:00
Masahiro Yamada c7836d1593 mmc: use empty initializer list to zero-clear structures
In the MMC subsystem, we see such initializers that only clears the
first member explicitly.

For example,

  struct mmc_request mrq = {NULL};

sets the first member (.sbc) to NULL explicitly.  However, this is
an unstable form because we may insert a non-pointer member at the
top of the struct mmc_request in the future. (if we do so, the
compiler will spit warnings.)

So, using a designated initializer is preferred coding style.  The
expression above is equivalent to:

  struct mmc_request mrq = { .sbc = NULL };

Of course, this does not express our intention.  We want to fill
all struct members with zeros.  Please note struct members are
implicitly zero-cleared unless otherwise specified in the initializer.

After all, the most reasonable (and stable) form is:

  struct mmc_request mrq = {};

Do likewise for mmc_command, mmc_data as well.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:54 +01:00
Geert Uytterhoeven 164b50b353 mmc: block: Replace "goto retry" by a proper do / while loop
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:53 +01:00
Geert Uytterhoeven 8cb6ed17eb mmc: block: Avoid uninitialized warning in mmc_blk_issue_discard_rq()
With gcc-4.1.2:

    mmc/core/block.c: In function ‘mmc_blk_issue_discard_rq’:
    mmc/core/block.c:1150: warning: ‘arg’ may be used uninitialized in this function
    mmc/core/block.c:1150: warning: ‘nr’ may be used uninitialized in this function
    mmc/core/block.c:1150: warning: ‘from’ may be used uninitialized in this function

While this is a false positive, it can be avoided easily by jumping over
the checks for "err" that are always false.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:53 +01:00
Jungseung Lee 46bc5c408e mmc: core: Export device lifetime information through sysfs
In the eMMC 5.0 version of the spec, several EXT_CSD fields about
device lifetime are added.

 - Two types of estimated indications reflected by averaged wear out of memory
 - An indication reflected by average reserved blocks

Export the information through sysfs.

Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:52 +01:00
Wolfram Sang b1c95170f9 mmc: sh_mobile_sdhi: enable HS200
Setup tuning when the board is HS200 enabled.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:52 +01:00
Wolfram Sang 03c5b0d903 mmc: sh_mobile_sdhi: remove superfluous check in SCC error check
The function will only be available if SDR104 was detected in probe,
so no need to check in the function itself again.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:51 +01:00
Wolfram Sang 7f9096f1c8 mmc: sh_mobile_sdhi: remove superfluous check in init_tuning
The function will only be available if SDR104 was detected in probe,
so no need to check in the function itself again.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:51 +01:00
Wolfram Sang 97c64b2cd5 mmc: sh_mobile_sdhi: remove superfluous check in hw_reset
The capability for HW_RESET is only activated if SDR104 is present, so
no need to check for SDR104 in the function itself again.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:50 +01:00
Wolfram Sang e831ead3b3 mmc: sh_mobile_sdhi: improve prerequisites for tuning
Prerequisites for tuning are the same as for hw_reset. We need an SCC
and a supported mode. Populate the tuning related functions only when
those conditions are met. This also removes a tiny race window.
Previously, the functions were populated when the SCC offset was not
initialized which could have led to an OOPS.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:49 +01:00
Wolfram Sang 6ade9a2c2d mmc: sh_mobile_sdhi: improve prerequisite for hw_reset
We need a SCC unit for hw_reset. Those units can only be described in
of_data. So, of_data and a valid SCC offset are prerequisites for
enabling the hw_reset capability. Merge the two 'if' conditions into one
and add a check for an scc offset.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:49 +01:00
Wolfram Sang dc9f1a8d79 mmc: sh_mobile_sdhi: simplify accessing DT data
By using the helper of_device_get_match_data(), we can skip some
checking and make the code simpler.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:48 +01:00
Wolfram Sang c51ff6c618 mmc: tmio: use SDIO master interrupt bit only when allowed
The master bit to enable SDIO interrupts can only be accessed if
SCLKDIVEN bit allows that. However, the core uses the SDIO enable
callback at times when SCLKDIVEN forbids the change. This leads to
"timeout waiting for SD bus idle" messages.

We now activate the master bit in probe once if SDIO is supported. IRQ
en-/disabling will be done now by the individual IRQ enablement bits
only.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:48 +01:00
Jean-Nicolas Graux 5cad24d835 mmc: mmci: avoid clearing ST Micro busy end interrupt mistakenly
This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.

A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches.  Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete.  As a result, mmcqd task
may be stuck forever.

Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:

..
[  240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[  240.257973]       Not tainted 4.1.13-00510-g9d91424 #2
[  240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.270955] mmcqd/1         D c047504c     0    52      2 0x00000000
[  240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[  240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[  240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[  240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[  240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[  240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[  240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[  240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[  240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[  240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[  240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[  240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[  240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[  240.670943]       Not tainted 4.1.13-00510-g9d91424 #2
[  240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.683922] partprobe       D c047504c     0   564    486 0x00000000
[  240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[  240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[  240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[  240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[  240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[  240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[  240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[  240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..

Here is the detailed sequence showing when this issue may happen:

1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.

2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).

3) Then mmci interrupt is raised and mmci_irq() is called:

MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)

Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.

Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.

Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.

Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case.  And we finally go
through following test at the end of while(status) loop:

/*
 * Don't poll for busy completion in irq context.
 */
if (host->variant->busy_detect && host->busy_status)
	status &= ~host->variant->busy_detect_flag;

Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:

a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)

Since MMCIMASK0 register is equal to 0x010003FF:

b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.

Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.

Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.

Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.

To fix the problem, this patch implements the following changes:

Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.

1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.

This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.

Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-08 12:22:27 +01:00
Christoph Hellwig 261c83c1a9 mmc: remove pointless request type check in mmc_prep_request
The block layer won't send requests the driver isn't asking for,
so remove this check.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31 14:00:10 -07:00
Gabriel Krisman Bertazi 161e6d44a5 mmc: sdhci: Ignore unexpected CARD_INT interrupts
One of our kernelCI boxes hanged at boot because a faulty eSDHC device
was triggering spurious CARD_INT interrupts for SD cards, causing CMD52
reads, which are not allowed for SD devices.  This adds a sanity check
to the interruption path, preventing that illegal command from getting
sent if the CARD_INT interruption should be disabled.

This quirk allows that particular machine to resume boot despite the
faulty hardware, instead of getting hung dealing with thousands of
mishandled interrupts.

Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: <stable@vger.kernel.org>
2017-01-31 11:26:49 +01:00
Ziyuan Xu e9748e0364 mmc: dw_mmc: force setup bus if active slots exist
It's necessary to setup bus if any slots are present.
- update clock after ctrl reset
- if the host has genpd node, we can guarantee the clock is
  available before starting request. Otherwies, the clock register
  is reset once power off the pd, and host can't output the active
  clock during communication.

Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Fixes: df9bcc2bc0 ("mmc: dw_mmc: add missing codes for runtime resume")
cc: <stable@vger.kernel.org>
Reported-by: Randy Li <randy.li@rock-chips.com>
Reported-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-01-23 10:19:30 +01:00
Ulf Hansson ee6ff743e3 mmc: core: Restore parts of the polling policy when switch to HS/HS DDR
Regressions for not being able to detect an eMMC HS DDR mode card has been
reported for the sdhci-esdhc-imx driver, but potentially other sdhci
variants may suffer from the similar problem.

The commit e173f8911f ("mmc: core: Update CMD13 polling policy when
switch to HS DDR mode"), is causing the problem. It seems that change moved
one step to far, regarding changing the host's timing before polling for a
busy card.

To fix this, let's move back to the behaviour when the host's timing is
updated after the polling, but before the switch status is fetched and
validated.

In cases when polling with CMD13, we keep validating the switch status at
each attempt. However, to align with the other card busy detections
mechanism, let's fetch and validate the switch status also after the host's
timing is updated.

Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Gary Bisson <gary.bisson@boundarydevices.com>
Fixes: e173f8911f ("mmc: core: Update CMD13 polling policy when switch..")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
2017-01-16 16:17:42 +01:00
Stefan Wahren 01167c7b9c mmc: mxs-mmc: Fix additional cycles after transmission stop
According to the code the intention is to append 8 SCK cycles
instead of 4 at end of a MMC_STOP_TRANSMISSION command. But this
will never happened because it's an AC command not an ADTC command.
So fix this by moving the statement into the right function.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-01-12 12:31:00 +01:00
Hans de Goede e1d070c379 mmc: sdhci-acpi: Only powered up enabled acpi child devices
Commit e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are
powered when probing") introduced code to powerup any acpi child
nodes listed in the dstd. But some dstd-s list all possible devices
used on some board variants, while reporting if the device is actually
present and enabled in the status field of the device.

So we end up calling the acpi _PS0 (power-on) method for devices which
are not actually present. This does not always end well, e.g. on my
cube iwork8 air tablet, this results in freezing the entire tablet as
soon as the r8723bs module is loaded.

This commit fixes this by checking the child device's status.present
and status.enabled bits and only call acpi_device_fix_up_power()
if both are set.

Fixes: e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are powered when probing")
BugLink: https://github.com/hadess/rtl8723bs/issues/80
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-01-12 12:15:20 +01:00
Heinrich Schuchardt 19a91dd4e3 MMC: meson: avoid possible NULL dereference
No actual segmentation faults were observed but the coding is
at least inconsistent.

irqreturn_t meson_mmc_irq():

We should not dereference host before checking it.

meson_mmc_irq_thread():

If cmd or mrq are NULL we should not dereference them after
writing a warning.

Fixes: 51c5d8447b MMC: meson: initial support for GX platforms
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-01-10 11:53:00 +01:00
Linus Torvalds 7c0f6ba682 Replace <asm/uaccess.h> with <linux/uaccess.h> globally
This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-24 11:46:01 -08:00
Paul Burton e85baa8868 mmc: sd: Meet alignment requirements for raw_ssr DMA
The mmc_read_ssr() function results in DMA to the raw_ssr member of
struct mmc_card, which is not guaranteed to be cache line aligned & thus
might not meet the requirements set out in Documentation/DMA-API.txt:

  Warnings:  Memory coherency operates at a granularity called the cache
  line width.  In order for memory mapped by this API to operate
  correctly, the mapped region must begin exactly on a cache line
  boundary and end exactly on one (to prevent two separately mapped
  regions from sharing a single cache line).  Since the cache line size
  may not be known at compile time, the API will not enforce this
  requirement.  Therefore, it is recommended that driver writers who
  don't take special care to determine the cache line size at run time
  only map virtual regions that begin and end on page boundaries (which
  are guaranteed also to be cache line boundaries).

On some systems where DMA is non-coherent this can lead to us losing
data that shares cache lines with the raw_ssr array.

Fix this by kmalloc'ing a temporary buffer to perform DMA into. kmalloc
will ensure the buffer is suitably aligned, allowing the DMA to be
performed without any loss of data.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 5275a652d2 ("mmc: sd: Export SD Status via “ssr” device attribute")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-21 08:34:30 +01:00
Adrian Hunter 1552011150 mmc: core: Further fix thread wake-up
Commit e0097cf5f2 ("mmc: queue: Fix queue thread wake-up") did not go far
enough. mmc_wait_for_data_req_done() still contains some problems and can
be further simplified.  First it should not touch
context_info->is_waiting_last_req because that is a wake-up control used by
the owner of the context. Secondly, it should always return when one of its
wake-up conditions is met because, again, that is contolled by the owner of
the context.

While the current block driver does not have an issue, these problems were
exposed during testing of the Software Command Queue patches.

Fixes: e0097cf5f2 ("mmc: queue: Fix queue thread wake-up")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-20 11:55:04 +01:00
Adrian Hunter 84ec048ba1 mmc: sdhci: Fix to handle MMC_POWER_UNDEFINED
Since commit c2c24819b2 ("mmc: core: Don't power off the card when
starting the host"), the power state can still be MMC_POWER_UNDEFINED after
mmc_start_host() is called. That can trigger a warning in SDHCI during
runtime resume as it tries to restore the I/O state. Handle
MMC_POWER_UNDEFINED simply by not updating the I/O state in that case.

Fixes: c2c24819b2 ("mmc: core: Don't power off the card when starting the host")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-20 11:42:33 +01:00
Masahiro Yamada 5b311c1519 mmc: sdhci-cadence: add Socionext UniPhier specific compatible string
Add a Socionext SoC specific compatible (suggested by Rob Herring).

No SoC specific data are associated with the compatible strings for
now, but other SoC vendors may use this IP and want to differentiate
IP variants in the future.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-20 11:40:52 +01:00
Linus Torvalds b9f98bd403 MMC core:
- Move files from the card directory to the core directory to enable
    future clean-ups of the generic mmc header files and interfaces.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJYURIiAAoJEP4mhCVzWIwpYAUQAL2qmTde04Qs/MjVtTCih3L0
 +ZB0oK/ppNUwZTmAJlMhi1osKPmdRd1Kngv+7zEBnddrbVJDAYrM+T5Psd8WebM4
 xUK0e3LnwuzFGskkgQ1mtd9qZHEniEdUg8Dq+nXSnGiesvCST2/uAAtjvFQHYr0R
 QK3U7hOyJBd1+L5LpPIIF+e/Ix7yaHobfYLGcGxRGULw5uhYiy3vbkpN7omD0hlQ
 2EYdBFcHj1GHarDYFtD3BWUNGtT7GpC10iMueUYVuz+bzOjCAhEeZ0Lh6V7R6HCr
 ZVSeMEK45HegLHx81XMDGYqDfRUPgShjNKrAq8DxfzBXvQ+1iuq5Mh01Zrilcxfw
 nNbqNajc+OIXluxYRz5h3HHC02R4gGN6Uk/gx/H8a/eRRcM6a3irDLkLBpyvETpb
 pH1OkomaHg5B/dTH0cUFamK/fTDNr3Lv2HFcKJ9ALQxhgEAQwcsWaeAyvvUncFuU
 /uiyd6NEWo/19mHB905wF5R9oTv1WWrQGDmSHGJT51Br1BJf+W/2ZT9N9P12zweW
 d5ZvheGymUjQ6yFnv5ov6udTWdogy8qqAihGa4kwPbfpY+DwlcT+pN/bej1pYwqQ
 kUxCxBE84RciJzZbped9xDo10HSGVudlIZPMa8Jp0f/CbPYnwf+z3tP6Xt5wtwLh
 jAhBjdzkWvEdTAJfyYmw
 =U2+h
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull another MMC update from Ulf Hansson:
 "Here's a second pull request for MMC for v4.10.

  As a matter of fact it's only one change that moves some mmc files
  around. I thought it was a good idea to get this into v4.10, as it
  gives us a nice and fresh base for v4.11. Summary:

  MMC core:

   - Move files from the card directory to the core directory to enable
     future clean-ups of the generic mmc header files and interfaces"

* tag 'mmc-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: block: Move files to core
2016-12-14 10:55:56 -08:00
Linus Torvalds 36869cb93d Merge branch 'for-4.10/block' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
 "This is the main block pull request this series. Contrary to previous
  release, I've kept the core and driver changes in the same branch. We
  always ended up having dependencies between the two for obvious
  reasons, so makes more sense to keep them together. That said, I'll
  probably try and keep more topical branches going forward, especially
  for cycles that end up being as busy as this one.

  The major parts of this pull request is:

   - Improved support for O_DIRECT on block devices, with a small
     private implementation instead of using the pig that is
     fs/direct-io.c. From Christoph.

   - Request completion tracking in a scalable fashion. This is utilized
     by two components in this pull, the new hybrid polling and the
     writeback queue throttling code.

   - Improved support for polling with O_DIRECT, adding a hybrid mode
     that combines pure polling with an initial sleep. From me.

   - Support for automatic throttling of writeback queues on the block
     side. This uses feedback from the device completion latencies to
     scale the queue on the block side up or down. From me.

   - Support from SMR drives in the block layer and for SD. From Hannes
     and Shaun.

   - Multi-connection support for nbd. From Josef.

   - Cleanup of request and bio flags, so we have a clear split between
     which are bio (or rq) private, and which ones are shared. From
     Christoph.

   - A set of patches from Bart, that improve how we handle queue
     stopping and starting in blk-mq.

   - Support for WRITE_ZEROES from Chaitanya.

   - Lightnvm updates from Javier/Matias.

   - Supoort for FC for the nvme-over-fabrics code. From James Smart.

   - A bunch of fixes from a whole slew of people, too many to name
     here"

* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
  blk-stat: fix a few cases of missing batch flushing
  blk-flush: run the queue when inserting blk-mq flush
  elevator: make the rqhash helpers exported
  blk-mq: abstract out blk_mq_dispatch_rq_list() helper
  blk-mq: add blk_mq_start_stopped_hw_queue()
  block: improve handling of the magic discard payload
  blk-wbt: don't throttle discard or write zeroes
  nbd: use dev_err_ratelimited in io path
  nbd: reset the setup task for NBD_CLEAR_SOCK
  nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
  nvme-fabrics: Add target support for FC transport
  nvme-fabrics: Add host support for FC transport
  nvme-fabrics: Add FC transport LLDD api definitions
  nvme-fabrics: Add FC transport FC-NVME definitions
  nvme-fabrics: Add FC transport error codes to nvme.h
  Add type 0x28 NVME type code to scsi fc headers
  nvme-fabrics: patch target code in prep for FC transport support
  nvme-fabrics: set sqe.command_id in core not transports
  parser: add u64 number parser
  nvme-rdma: align to generic ib_event logging helper
  ...
2016-12-13 10:19:16 -08:00
Ulf Hansson f397c8d80a mmc: block: Move files to core
Once upon a time it made sense to keep the mmc block device driver and its
related code, in its own directory called card. Over time, more an more
functions/structures have become shared through generic mmc header files,
between the core and the card directory. In other words, the relationship
between them has become closer.

By sharing functions/structures via generic header files, it becomes easy
for outside users to abuse them. In a way to avoid that from happen, let's
move the files from card directory into the core directory, as it enables
us to move definitions of functions/structures into mmc core specific
header files.

Note, this is only the first step in providing a cleaner mmc interface for
outside users. Following changes will do the actual cleanup, as that is not
part of this change.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-12 16:30:05 +01:00
Masahiro Yamada ff6af28faf mmc: sdhci-cadence: add Cadence SD4HC support
Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.

For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-08 15:02:52 +01:00
Masahiro Yamada 85a882c2e9 mmc: sdhci: export sdhci_execute_tuning()
Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.

Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.

This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-08 15:02:45 +01:00
Adrian Hunter 6b11e70bb7 mmc: sdhci: Tidy tuning loop
Tidy the tuning loop by moving it to a separate function and making it a
for-loop.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:24 +01:00
Adrian Hunter 85336109c0 mmc: sdhci: Simplify tuning block size logic
There are only 2 possible block sizes, so simplify 2 if-statements into 1.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:24 +01:00
Adrian Hunter da4bc4f285 mmc: sdhci: Factor out tuning helper functions
Factor out some functions to tidy up the code in sdhci_execute_tuning.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:23 +01:00
Adrian Hunter d0c3ab5910 mmc: sdhci: Use mmc_abort_tuning()
Use mmc_abort_tuning() instead of open-coding the stop command.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:23 +01:00
Adrian Hunter e711f03091 mmc: mmc: Introduce mmc_abort_tuning()
If a tuning command times out, the card could still be processing it, which
will cause problems for recovery. The eMMC specification says that CMD12
can be used to stop CMD21, so add a function that does that.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:22 +01:00
Adrian Hunter 0760c35552 mmc: sdhci: Always allow tuning to fall back to fixed sampling
SDHCI falls back to fixed sampling if there is an error during tuning.
However it also reports an error unless there is periodic re-tuning.
That is not the best option because:
a) there is a reasonable chance that fixed sampling will work, especially
at room temperature.
b) re-tuning will be done again anyway if there are CRC errors.
Change to return no error always when falling back to fixed sampling.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:21 +01:00
Adrian Hunter 5ef5203b95 mmc: sdhci: Fix tuning reset after exhausting the maximum number of loops
If the driver has exhausted the maximum number of tuning loops, then fixed
sampling is used. To do that both SDHCI_CTRL_TUNED_CLK and
SDHCI_CTRL_EXEC_TUNING must be reset to 0, but only SDHCI_CTRL_TUNED_CLK
was being reset. Reset SDHCI_CTRL_EXEC_TUNING to 0 also.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:21 +01:00
Adrian Hunter 61e53bd004 mmc: sdhci: Fix recovery from tuning timeout
Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.

Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.

Note that this replaces the commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dan O'Donovan <dan@emutex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:20 +01:00
Adrian Hunter 2ca71c27ee Revert "mmc: sdhci: Reset cmd and data circuits after tuning failure"
This reverts commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and data circuits
after tuning failure").

A better fix is available, and it will be applied to older stable releases,
so get this out of the way by reverting it.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:16:20 +01:00
Adrian Hunter ef3d232245 mmc: mmc: Relax checking for switch errors after HS200 switch
The JEDEC specification indicates CMD13 can be used after a HS200 switch
to check for errors. However in practice some boards experience CRC errors
in the CMD13 response. Consequently, for HS200, CRC errors are not a
reliable way to know the switch failed. If there really is a problem, we
would expect tuning will fail and the result ends up the same. So change
the error condition to ignore CRC errors in that case.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 14:15:46 +01:00
Daniel Drake db52d4f8a4 mmc: sdhci-acpi: support 80860F14 UID 2 SDIO bus
Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:

  Device (SDHB) {
    Name (_ADR, 0x00110000)
    Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
    Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
    Name (_DDN, "Intel(R) SDIO Controller - 80862295")
    Name (_UID, 0x02)
    Name (_HRV, One)

A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 11:13:24 +01:00
Masahiro Yamada 8baa74f3dd mmc: sdhci-of-at91: remove bogus MMC_SDHCI_IO_ACCESSORS select
I see no override of read/write callbacks in sdhci-of-at91.c.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:32:49 +01:00
Zach Brown 3f23df72dc mmc: sdhci-pci: Use ACPI to get max frequency for Intel NI byt sdio
On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.

The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.

Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:19 +01:00
Zach Brown 42b0649640 mmc: sdhci-pci: Add PCI ID for Intel NI byt sdio
Add PCI ID for Intel byt sdio host controller sub-vended by NI.

The controller has different behavior because of the board layout NI
puts it on.

Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:18 +01:00
Jaehoon Chung 69be8522a2 mmc: sdhci-s3c: add spin_unlock_irq() before calling clk_round_rate
Before calling clk_round_rate(), put the spin_unlock_irq() in
sdhci_s3c_consider_clock() function.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:17 +01:00
Jaehoon Chung e6cd7a8ea1 mmc: dw_mmc: display the clock message only one time when card is polling
When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:17 +01:00
Jaehoon Chung d10111cf85 mmc: dw_mmc: add the debug message for polling and non-removable
If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:16 +01:00
Jaehoon Chung 1c238a95a7 mmc: dw_mmc: check the "present" variable before checking flags
Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:15 +01:00
Joonyoung Shim df9bcc2bc0 mmc: dw_mmc: add missing codes for runtime resume
The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:15 +01:00
Joonyoung Shim 9b93d392fd mmc: dw_mmc: exynos: fix to call suspend callback
The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:14 +01:00
Shawn Lin f28ef56172 mmc: mmc_test: remove BUG_ONs and deploy error handling
It is unnecessary to panic the kernel when testing mmc. Instead,
cast a warning for folkz to debug and return the error code to
the caller to indicate the failure of this test should be enough.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:13 +01:00
Shawn Lin 8508cb9868 mmc: queue: remove BUG_ON for bounce_sg
bounce_sg for mqrq_cur and mqrq_pre are proper
allocated when initializing the queue and will not
be freed before explicitly cleaning the queue. So from
the code itself it should be quite confident to remove
this check. If that BUG_ON take effects, it is mostly
likely the memory is randomly oopsing.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:13 +01:00
Shawn Lin 8664dccf3a mmc: sdio_uart: remove meaningless BUG_ON
The code seems quite simple to maintain the sdio_uart_table,
and the insert/remove port from the table are symmetric. If
the BUG_ON occurs, which means serial_core modify the index
or mess up the port sequence anyway.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:12 +01:00
Shawn Lin 6ff897ff5c mmc: core: remove BUG_ONs from core.c
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:11 +01:00
Shawn Lin 349583d666 mmc: core: remove BUG_ONs from sd
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:10 +01:00
Shawn Lin 8cce3ecc53 mmc: core: remove BUG_ONs from mmc
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:09 +01:00
Shawn Lin a48ee3e65a mmc: debugfs: remove BUG_ON from mmc_ext_csd_open
Return error value for file_operations callback instead
of triggering BUG_ON which is meaningless. Personally I
don't believe n != EXT_CSD_STR_LEN could happen. Anyway,
propagate the error to the caller.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:09 +01:00
Shawn Lin 5df0e8231f mmc: core: remove BUG_ONs from sdio
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:08 +01:00
Adrian Hunter 925ff3a7a3 mmc: mmc: Add Command Queue definitions
Add definitions relating to Command Queuing.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:07 +01:00
Adrian Hunter c5bda0ca6f mmc: queue: Introduce queue depth and use it to allocate and free
Add a mmc_queue member to record the size of the queue, which currently
supports 2 requests on-the-go at a time. Instead of allocating resources
for 2 slots in the queue, allow for an arbitrary number.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:07 +01:00
Adrian Hunter c09949cff5 mmc: queue: Factor out mmc_queue_reqs_free_bufs()
In preparation for supporting a queue of requests, factor out
mmc_queue_reqs_free_bufs().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:06 +01:00
Adrian Hunter 64e29e42a6 mmc: queue: Factor out mmc_queue_alloc_sgs()
In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_sgs().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:05 +01:00
Adrian Hunter f2b8b522cf mmc: queue: Factor out mmc_queue_alloc_bounce_sgs()
In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_bounce_sgs().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
[Ulf: Fixed compiler warning]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:05 +01:00
Adrian Hunter c853982ece mmc: queue: Factor out mmc_queue_alloc_bounce_bufs()
In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_bounce_bufs().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
[Ulf: Fixed compiler warning]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:04 +01:00
Adrian Hunter e0097cf5f2 mmc: queue: Fix queue thread wake-up
The only time the driver sleeps expecting to be woken upon the arrival of
a new request, is when the dispatch queue is empty. The only time that it
is known whether the dispatch queue is empty is after NULL is returned
from blk_fetch_request() while under the queue lock.

Recognizing those facts, simplify the synchronization between the queue
thread and the request function. A couple of flags tell the request
function what to do, and the queue lock and barriers associated with
wake-ups ensure synchronization.

The result is simpler and allows the removal of the context_info lock.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:03 +01:00
Adrian Hunter 5be80375f5 mmc: block: Fix 4K native sector check
The 4K native sector check does not allow for the 'do' loop nor the
variables used after the 'cmd_abort' label.

'brq' and 'req' get reassigned in the 'do' loop, so the check must not
assume what their values are. After the 'cmd_abort' label, 'mq_rq' and
'req' are used, but 'rqc' must be NULL otherwise it can be started again.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:03 +01:00
Adrian Hunter 5dd784d2e4 mmc: block: Restore line inadvertently removed with packed commands
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-05 10:30:34 +01:00
yangbo lu 151ede40fd mmc: sdhci-of-esdhc: fix host version for T4240-R1.0-R2.0
The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:17:21 +01:00
Linus Walleij 03d640ae1f mmc: block: delete packed command support
I've had it with this code now.

The packed command support is a complex hurdle in the MMC/SD block
layer, around 500+ lines of code which was introduced in 2013 in

commit ce39f9d17c ("mmc: support packed write command for eMMC4.5
devices")
commit abd9ac1449 ("mmc: add packed command feature of eMMC4.5")

...and since then it has been rotting. The original author of the
code has disappeared from the community and the mail address is
bouncing.

For the code to be exercised the host must flag that it supports
packed commands, so in mmc_blk_prep_packed_list() which is called for
every single request, the following construction appears:

u8 max_packed_rw = 0;

if ((rq_data_dir(cur) == WRITE) &&
    mmc_host_packed_wr(card->host))
        max_packed_rw = card->ext_csd.max_packed_writes;

if (max_packed_rw == 0)
    goto no_packed;

This has the following logical deductions:

- Only WRITE commands can really be packed, so the solution is
  only half-done: we support packed WRITE but not packed READ.
  The packed command support has not been finalized by supporting
  reads in three years!

- mmc_host_packed_wr() is just a static inline that checks
  host->caps2 & MMC_CAP2_PACKED_WR. The problem with this is
  that NO upstream host sets this capability flag! No driver
  in the kernel is using it, and we can't test it. Packed
  command may be supported in out-of-tree code, but I doubt
  it. I doubt that the code is even working anymore due to
  other refactorings in the MMC block layer, who would
  notice if patches affecting it broke packed commands?
  No one.

- There is no Device Tree binding or code to mark a host as
  supporting packed read or write commands, just this flag
  in caps2, so for sure there are not any DT systems using
  it either.

It has other problems as well: mmc_blk_prep_packed_list() is
speculatively picking requests out of the request queue with
blk_fetch_request() making the MMC/SD stack harder to convert
to the multiqueue block layer. By this we get rid of an
obstacle.

The way I see it this is just cruft littering the MMC/SD
stack.

Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Maya Erez <qca_merez@qca.qualcomm.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:27 +01:00
Linus Walleij d3c6aac3bd mmc: delete is_first_req parameter from pre-request callback
The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.

None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.

Delete the parameter from the callback and all users, as it is
just pointless cruft.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:27 +01:00
Ulf Hansson e173f8911f mmc: core: Update CMD13 polling policy when switch to HS DDR mode
According to the JEDEC specification, during bus timing change operations
for mmc, sending a CMD13 could trigger CRC errors.

As switching to HS DDR mode indeed causes a bus timing change, polling with
CMD13 to detect card busy, may thus potentially trigger CRC errors.
Currently these errors are treated as the switch to HS DDR mode failed.

To improve this behaviour, let's instead tell __mmc_switch() to retry when
it encounters CRC errors during polling.

Moreover, when switching to HS DDR mode, let's make sure the CMD13 polling
is done by having the mmc host and the mmc card, being configured to
operate at the same selected bus speed timing. Fix this by providing
MMC_TIMING_MMC_DDR52 as the timing parameter to __mmc_switch().

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-11-29 09:05:26 +01:00
Ulf Hansson 53e60650f7 mmc: core: Allow CMD13 polling when switching to HS mode for mmc
In cases when the mmc host doesn't support HW busy detection, polling for a
card being busy by using CMD13 is beneficial. That is because, instead of
waiting a fixed amount of time, 500ms or the generic CMD6 time from
EXT_CSD, we find out a lot sooner when the card stops signaling busy. This
leads to a significant decreased total initialization time for the mmc
card.

However, to allow polling with CMD13 during a bus timing change operation,
such as switching to HS mode, we first need to update the mmc host's bus
timing before starting to poll. Deal with that, simply by providing
MMC_TIMING_MMC_HS as the timing parameter to __mmc_switch() from
mmc_select_hs().

By telling __mmc_switch() to allow polling with CMD13, also makes it
validate the CMD6 status, thus we can remove the corresponding checks.

When switching to HS400ES, the mmc_select_hs() function is called in one of
the intermediate steps. To still prevent CMD13 polling for HS400ES, let's
call the __mmc_switch() function in this path as it enables us to keep
using the existing method.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-11-29 09:05:25 +01:00
Ulf Hansson aa33ce3c41 mmc: core: Enable __mmc_switch() to change bus speed timing for the host
In cases when a speed mode change is requested for mmc cards, a CMD6 is
sent by calling __mmc_switch() during the card initialization. The CMD6
leads to the card entering a busy period. When that is completed, the host
must parse the CMD6 status to find out whether the change of the speed mode
succeeded.

To enable the mmc core to poll the card by using CMD13 to find out when the
busy period is completed, it's reasonable to make sure polling is done by
having the mmc host and the mmc card, being configured to operate at the
same selected bus speed timing.

Therefore, let's extend __mmc_switch() to take yet another parameter, which
allow its callers to update the bus speed timing of the mmc host. In this
way, __mmc_switch() also becomes capable of reading and validating the CMD6
status by sending a CMD13, in cases when that's desired.

If __mmc_switch() encounters a failure, we make sure to restores the old
bus speed timing for the mmc host, before propagating the error code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-11-29 09:05:25 +01:00
Ulf Hansson 5ec32f8411 mmc: core: Check SWITCH_ERROR bit from each CMD13 response when polling
According to the JEDEC specification, the SWITCH_ERROR bit in the device
status from a R1 response, is an error bit which may be cleared as soon as
the response that reports the error is sent.

When polling with CMD13 to find out when the card stops signaling busy
after a CMD6 has been sent, we currently parse only the last CMD13 response
for the SWITCH_ERROR bit. Consequentially we could loose important
information about the card.

In worst case if the card stops signaling busy within the allowed timeout,
we could end up believing that the CMD6 command completed successfully,
when in fact it didn't.

To improve the behaviour, let's parse each CMD13 response to see if the
SWITCH_ERROR bit is set in the device status. In such case, we abort the
polling loop and report the error.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-11-29 09:05:24 +01:00
Ulf Hansson 625228fa3e mmc: core: Rename ignore_crc to retry_crc_err to reflect its purpose
The ignore_crc parameter/variable name is used at a couple of places in the
mmc core. Let's rename it to retry_crc_err to reflect its new purpose.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-11-29 09:05:23 +01:00
Ulf Hansson 89e57aedda mmc: core: Remove redundant __mmc_send_status()
There are only one users left which calls __mmc_send_status(). Moreover,
the ignore_crc parameter isn't being used, so let's just remove these
redundant parts.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-11-29 09:05:23 +01:00
Ulf Hansson 437590a123 mmc: core: Retry instead of ignore at CRC errors when polling for busy
After a CMD6 command has been sent, the __mmc_switch() function might be
advised to poll the card for busy by using CMD13 and also by ignoring CRC
errors.

In the case of ignoring CRC errors, the mmc core tells the mmc host to also
ignore these errors via masking the MMC_RSP_CRC response flag. This seems
wrong, as it leads to that the mmc host could propagate an unreliable
response, instead of a proper error code.

What we really want, is not to ignore CRC errors but instead retry the
polling attempt. So, let's change this by treating a CRC error as the card
is still being busy and thus continue to run the polling loop.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-11-29 09:05:22 +01:00
David E. Box 8f743d0394 mmc: sdhci-pci: Allow deferred probe for sd card detect gpio
With commit f35bbf61ab ("gpio / ACPI: Return -EPROBE_DEFER if the
gpiochip was not found"), a gpio descriptor request can now be deferred if
the providing gpio host controller driver hasn't been loaded yet. Allow use
in mmc slot probe in order to prevent card detect gpio setup from failing
in this case.

Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:21 +01:00
Adrian Hunter 2d1956d0a4 mmc: sdhci-pci: Add support for Intel GLK
Add support for eMMC/SD/SDIO Intel GLK host controllers.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:20 +01:00
Ritesh Harjani 02e4293dc0 sdhci: sdhci-msm: update dll configuration
The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.

The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.

The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:20 +01:00
Ritesh Harjani cc392c583d mmc: sdhci-msm: Add calibration tuning for CDCLP533 circuit
In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.

The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:19 +01:00
Ritesh Harjani abf270e5c6 mmc: sdhci-msm: Save the calculated tuning phase
Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:18 +01:00
Venkat Gopalakrishnan ff06ce4178 mmc: sdhci-msm: Add HS400 platform support
The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:18 +01:00
Ritesh Harjani b12d44db4b mmc: sdhci-msm: Add clock changes for DDR mode.
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:17 +01:00
Ritesh Harjani edc609fd19 mmc: sdhci-msm: Implement set_clock callback for sdhci-msm
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.

Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:16 +01:00
Ritesh Harjani fec7967397 mmc: sdhci: Factor out sdhci_enable_clk
Factor out sdhci_enable_clk from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:15 +01:00
Ritesh Harjani a0e3142869 mmc: sdhci-msm: Enable few quirks
sdhc-msm controller needs this SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN
& SDHCI_QUIRK2_PRESET_VALUE_BROKEN to be set. Hence setting it.

Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:15 +01:00
Ritesh Harjani 80031bdeb7 mmc: sdhci-msm: Add get_min_clock() and get_max_clock() callback
This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.

Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:14 +01:00
Venkat Gopalakrishnan 83736352e0 mmc: sdhci-msm: Update DLL reset sequence
SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.

Without this patch we see below errors on such SDHC controllers
	sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
	mmc0: tuning execution failed: -110

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:13 +01:00
Ritesh Harjani 29301f40cb mmc: sdhci-msm: Change poor style writel/readl of registers
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:12 +01:00
Jaehoon Chung b023030f10 mmc: dw_mmc: The "clock-freq-min-max" property was deprecated
The "clock-freq-min-max" property was deprecated.
There is "max-frequency" property in drivers/mmc/core/host.c
"max-frequency" can be replaced with "clock-freq-min-max".
Minimum clock value might be set to 100K by default.
Then MMC core should try to find the correct value from 400K to 100K.
So it just needs to set Maximum clock value.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:11 +01:00
Jaehoon Chung 0349c0854e mmc: dw_mmc: remove the unnecessary mmc_data structure
Remove the unnecessary mmc_data structure.
Instead, cmd->data can be used.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:10 +01:00
Jaehoon Chung a4cc7eb441 mmc: dw_mmc: use the cookie's enum values for post/pre_req()
This patch removed the meaningless value. Instead, use the cookie's enum
values for executing correctly.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:09 +01:00
Jaehoon Chung e13c3c0818 mmc: dw_mmc: call the dw_mci_prep_stop_abort() by default
stop_cmdr should be set to values relevant to stop command.
It migth be assigned to values whatever there is mrq->stop or not.
Then it doesn't need to use dw_mci_prepare_command().
It's enough to use the prep_stop_abort for preparing stop command.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:09 +01:00
Jaehoon Chung 8c005b4090 mmc: dw_mmc: use the hold register when send stop command
If DW_MMC_CARD_NO_USE_HOLD isn't set, it's usesd by default.
Enve if SDMMC_CMD_USB_HOLD_REG is set in prepare_command(), but it
doesn't set in pre_stop_abort().

To maintain the consistency, add the checking condition for this.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:08 +01:00
Jaehoon Chung 72e83577bc mmc: dw_mmc: change the DW_MCI_FREQ_MIN from 400K to 100K
If there is no property "clock-freq-min-max", mmc->f_min should be set
to 400K by default. But Some SoC can be used 100K.
When 100K is used, MMC core will try to check from 400K to 100K.

Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:07 +01:00
Jaehoon Chung 1f4d50790b mmc: dw_mmc: fix the debug message for checking card's present
If display the debug message, this message should be spamming.
If flags is maintained the previous value, didn't display the debug
message.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:07 +01:00
Jaehoon Chung 21657ebd63 mmc: dw_mmc: display the real register value on debugfs
Developer wants to see the real register value, not register offset.
This patch fixed to display the real value of register.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:06 +01:00
Colin Ian King 26be9d705f mmc: dw_mmc: fix spelling mistake in dev_dbg message
Trivial fix to spelling mistake "desciptor" to "descriptor" in
dev_dbg message.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:05 +01:00
Linus Walleij e01071dd2b mmc: block: move packed command struct init
By moving the mmc_packed_init() and mmc_packed_clean() into the
only file in the kernel where they are used, we save two exported
functions and can staticize those to the block.c file.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:04 +01:00
Linus Walleij 7db3028e00 mmc: block: rename data to blkdata
The struct mmc_blk_request contains an opaque void *data that
is actually only used to store a pointer to a per-request
struct mmc_blk_data. This is confusing, so rename the member
to blkdata and forward-declare the block.c local struct.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:04 +01:00
Linus Walleij f2818bff37 mmc: block: use mmc_req_is_special()
Instead of open coding the check for the same thing that
the helper checks: use the helper.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:03 +01:00
ahaslam@baylibre.com 6e628dad65 mmc: davinci: request gpios using gpio descriptors
Request card detect and write protect gpios using the provided API
by mmc core.

If a gpio is provided for card detect, we don't need to poll.
So only use polling when a gpio is not provided.

Once all pdata users register the gpios using gpio descriptors,
we could remove the platform callbacks.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
2016-11-29 09:04:53 +01:00
ahaslam@baylibre.com c8301e798f mmc: davinci: use mmc_of_parse to parse common mmc configuration
Card detect and write protect are currently not working on a DT
boot, and the driver relies on polling to get the state
of the card. The current code depends on platform data callbacks
to register and get the state of the gpios.

mmc core provides a generic way to parse device tree configuration,
which will take care of registering the gpios for us, lets use it
so that we don't need to poll, and parse the same properties.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
2016-11-29 09:04:39 +01:00
Wolfram Sang e726e8c959 mmc: tmio: remove SDIO from TODO list
We surely have SDIO support by now :)

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:01:04 +01:00
Wolfram Sang 0c4bf5beff mmc: tmio: fix wrong bitmask for SDIO irqs
Commit 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
refactored the sdio irq handler and wrongly used the mask for SD irqs,
not for SDIO irqs. This doesn't really matter in practice because both
values keep the only interrupt we are interested in. But still, this is
wrong and wants to be fixed.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:01:03 +01:00
Alexey Khoroshilov a5488a35ba mmc: wbsd: implement check for dma mapping error
wbsd_request_dma() does not check for dma mapping errors.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:01:02 +01:00
Dan Carpenter 16652a936e mmc: mmc_test: Uninitialized return value
We never set "ret" to RESULT_OK.

Fixes: 9f9c4180f8 ("mmc: mmc_test: add test for non-blocking transfers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:01:01 +01:00
Masahiro Yamada 178b0fa0d4 mmc: sdhci: remove unneeded (void *) casts in sdhci_(pltfm_)priv()
The type of host->private is (unsigned long *).  No cast is needed
to return an opaque pointer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:01:00 +01:00
Scott Branden c833e92bbb mmc: sdhci-iproc: support standard byte register accesses
Add bytewise register accesses support for newer versions of IPROC
SDHCI controllers.
Previous sdhci-iproc versions of SDIO controllers
(such as Raspberry Pi and Cygnus) only allowed for 32-bit register
accesses.

Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:01:00 +01:00
Simon Horman 06f438dd38 mmc: sh_mobile_sdhi: Add tuning support
Add tuning support for use with SDR104 mode
This includes adding support for the sampling clock controller (SCC).

Based on work by Ai Kyuse.

Cc: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:58 +01:00
Ai Kyuse 4f11997773 mmc: tmio: Add tuning support
Add tuning support for use with SDR104 mode

Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:57 +01:00
Ai Kyuse e8f36b5d3b mmc: tmio: Add hw reset support
Add hw reset support.

Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:57 +01:00
Simon Horman 2f87365f83 mmc: tmio: document mandatory and optional callbacks
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:56 +01:00
Ai Kyuse 96e0b2ba00 mmc: tmio: enhance illegal sequence handling
An illegal sequence command error may occur if there is a stopbit or
cmd_index error as well as a CRC error. The correct course of action
is to re-enable IRQs

An illegal sequence data error may occur if there is a CRC or stopbit
error,  or underrun. In this case set data->error correctly.

This is in preparation for enabling tuning support which relies on
differentiating between illegal sequence and other errors.

Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
[simon: broken out of a larger patch]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:55 +01:00
Chris Brandt 0963dd56b1 mmc: sh_mobile_sdhi: Add r7s72100 support
Add support for r7s72100 SoC.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:53 +01:00
Chris Brandt 8185e51f35 mmc: tmio-mmc: add support for 32bit data port
For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:53 +01:00
Chris Brandt f19417f382 mmc: sh_mobile_sdhi: add ocr_mask option
In moving platforms from board files to DT, there still needs to be a way
to set the ocr_mask setting for the tmio driver during probe. Without this
setting, the probe will fail because the supported voltages are not known.

This patch will also traditional platform registration platforms to
migrate to DT.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:52 +01:00
Linus Walleij 8e8b3f514c mmc: core: use enum mmc_blk_status properly
There were several instances of code using the
enum mmc_blk_status by arbitrarily converting it to an int and
throwing it around to different functions. This makes the code
hard to understand to may give rise to strange errors.

Especially the function prototype mmc_start_req() had to be
modified to take a pointer to an enum mmc_blk_status and the
function pointer .err_check() inside struct mmc_async_req
needed to return an enum mmc_blk_status.

In every case: instead of assigning the block layer error code
to an int, use the enum, also change the signature of all
functions actually passing this enum to use the enum.

To make it possible to use the enum everywhere applicable, move
it to <linux/mmc/core.h> so that all code actually using it can
also see it.

An interesting case was encountered in the MMC test code which
did not return a enum mmc_blk_status at all in the .err_check
function supposed to check whether asynchronous requests worked
or not: instead it returned a normal -ERROR or even the test
frameworks internal error codes.

The test code would also pass on enum mmc_blk_status codes as
error codes inside the test code instead of converting them
to the local RESULT_* codes.

I have tried to fix all instances properly and run some tests
on the result.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:51 +01:00
Linus Walleij 2cc6458708 mmc: block: convert ecc_err to a bool
The ecc_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:50 +01:00
Linus Walleij c44d6cefdf mmc: block: make gen_err a bool variable
This gen_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:49 +01:00
Zach Brown 92e0c44b92 mmc: sdhci: Use sdhci-caps-mask and sdhci-caps to change the caps read during __sdhci_read_caps
The sdhci capabilities register can be incorrect. The sdhci-caps-mask
and sdhci-caps dt properties specify which bits of the register are
incorrect and what their values should be. This patch makes the sdhci
driver use those properties to correct the caps during
__sdhci_read_caps.

During __sdhci_read_caps
Use the sdhci-caps-mask property to turn off the incorrect bits of the
sdhci register after reading them.
Use the sdhci-caps to turn on bits after using sdhci-caps-mask to turn
off the incorrect ones.

Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:48 +01:00
Linus Walleij 49adc0cacb mmc: mmci: refactor ST Micro busy detection
The ST Micro-specific busy detection was made after the assumption
that only this variant supports busy detection. So when doing busy
detection, the host immediately tries to use some ST-specific
register bits.

Since the qualcomm variant also supports some busy detection
schemes, encapsulate the variant flags better in the variant struct
and prepare to add more variants by just providing some bitmasks
to the logic.

Put the entire busy detection logic within an if()-clause in the
mmci_cmd_irq() function so the code is only executed when busy
detection is enabled, and so that it is kept in (almost) one
place, and add comments describing what is going on so the
code can be understood.

Tested on the Ux500 by introducing some prints in the busy
detection path and noticing how the IRQ is enabled, used and
disabled successfully.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:47 +01:00
Linus Walleij 5db3eee7b9 mmc: mmci: clean up header defines
There was some confusion in the CPSM (Command Path State Machine)
and DPSM (Data Path State Machine) regarding the naming of the
registers, clarify the meaning of this acronym so the naming is
understandable, and consistently use BIT() to define these fields.

Consequently name the register bit defines MCI_[C|D]PSM_* and
adjust the driver as well.

Include new definitions for a few bits found in a patch from
Srinivas Kandagatla.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:46 +01:00
Sylwester Nawrocki 18fae5c45c mmc: s3cmci: Use DMA slave map rather than exported DMA filter
Support for DMA slave map has been added to the s3c24xx-dma
controller in commit 34681d84a0
"dmaengine: s3c24xx: Add dma_slave_map for s3c2440 devices"
This patch converts the s3cmci driver to also use it, so we can
eventually get rid of the exported filter function once all
related DMA clients are updated.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:45 +01:00
Ulf Hansson c2c24819b2 mmc: core: Don't power off the card when starting the host
The MMC_CAP2_NO_PRESCAN_POWERUP was invented to avoid running the power up
sequence, mmc_power_up(), during ->probe() of the mmc host driver, but
instead defer this to the mmc detect work. This is especially useful for
those hosts that suffers from a long initialization time, as this time
would otherwise add up to the total boot time.

However, due to the introduction of runtime PM of mmc host devices in the
mmc core, this behaviour changed a bit. More precisely, it caused the mmc
core to runtime resume the host device during ->probe() of the host driver.
In cases like the rtsx_usb_sdmmc, runtime resuming the device may be costly
and thus affecting the total boot time.

To improve this behaviour when using MMC_CAP2_NO_PRESCAN_POWERUP, let's
postpone also calling mmc_power_off() when starting the host. This change
allows the mmc core to avoid runtime resuming the device, as it don't need
to claim the host for that execution path.

Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:44 +01:00
Kevin Hilman 51c5d8447b MMC: meson: initial support for GX platforms
Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:43 +01:00
Shawn Lin ed24e1ff5a mmc: dw_mmc: remove system PM callback
Now there are no variant drivers using dw_mci_suspend
and dw_mci_resume, so let's remove it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:42 +01:00
Shawn Lin ee2112be41 mmc: dw_mmc-pltfm: deploy runtime PM facilities
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:41 +01:00
Shawn Lin 53b2728811 mmc: dw_mmc-pci: deploy runtime PM facilities
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:40 +01:00
Shawn Lin cf5237eff9 mmc: dw_mmc-exynos: deploy runtime PM facilities
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:39 +01:00
Shawn Lin 2c8ae20e6c mmc: dw_mmc-k3: deploy runtime PM facilities
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:39 +01:00
Shawn Lin 1f5c51d76e mmc: dw_mmc: disable biu clk if possible
We could disable biu clk if gpio card detect available,
or it is a non-removable device.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:38 +01:00
Shawn Lin 50fcbbbb79 mmc: core: expose the capability of gpio card detect
Add new helper API mmc_can_gpio_cd for slot-gpio to make
host drivers know whether it supports gpio card detect.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:37 +01:00
Shawn Lin f90142683f mmc: dw_mmc-rockchip: add runtime PM support
This patch adds runtime PM support for dw_mmc-rockchip.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:36 +01:00
Shawn Lin e9ed8835e9 mmc: dw_mmc: add runtime PM callback
This patch add dw_mci_runtime_suspend/resume interfaces
and expose it to dw_mci variant driver to support runtime
PM.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:36 +01:00
Ulf Hansson 70562644f4 mmc: core: Don't use ->card_busy() and CMD13 in combination when polling
When polling for busy after sending a MMC_SWITCH command, both the optional
->card_busy() callback and CMD13 are being used in conjunction.

This doesn't make sense. Instead it's more reasonable to rely solely on the
->card_busy() callback when it exists. Let's change that and instead use
the CMD13 as a fall-back. In this way we avoid sending CMD13, unless it's
really needed.

Within this context, let's also take the opportunity to make some
additional clean-ups and clarifications to the related code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-11-29 09:00:35 +01:00
Ulf Hansson 716bdb8953 mmc: core: Factor out code related to polling in __mmc_switch()
In yet another step of cleaning up __mmc_switch(), let's factor out the
code that deals with card busy polling.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-11-29 09:00:34 +01:00
Ulf Hansson cb26ce069f mmc: core: Clarify code which deals with polling in __mmc_switch()
The __mmc_switch() deserves a clean-up. In this step, let's move some code
outside of the do-while loop, which deal deals with the card busy polling.

This change simplifies the code in that sense that it becomes easier to follow
what is being executed during card busy polling, but it also gives a better
understanding for when polling isn't done.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-11-29 09:00:33 +01:00
Ulf Hansson 20348d1981 mmc: core: Make mmc_switch_status() available for mmc core
Following changes needs mmc_switch_status() to be available both from mmc.c
and mmc_ops.c. Allow that by moving its implementation to mmc_ops.c and
make it available via mmc_ops.h.

Moving mmc_switch_status() to mmc_ops.c, also enables us to turn
mmc_switch_status_error() into static function. So let's take the
opportunity to change this as well.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-11-29 09:00:33 +01:00
Pramod Gurav 67e6db113c mmc: sdhci-msm: Add pm_runtime and system PM support
Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.

Reviewed-by: Ritesh Harjani <riteshh@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:32 +01:00
Maxime Ripard 424feb59d8 mmc: sunxi: Prevent against null dereference for vmmc
VMMC is an optional regulator, which means that mmc_regulator_get_supply
will only return an error in case of a deferred probe, but not when the
regulator is not set in the DT.

However, the sunxi driver assumes that VMMC is always there, and doesn't
check the value of the regulator pointer before using it, which obviously
leads to a (close to) null pointer dereference.

Add proper checks to prevent that.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:31 +01:00
Javier Martinez Canillas d9943c6830 mmc: sdhci-of-at91: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
$

After this patch:

$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
alias:          of:N*T*Catmel,sama5d2-sdhciC*
alias:          of:N*T*Catmel,sama5d2-sdhci

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:29 +01:00
Javier Martinez Canillas 9cb02eefec mmc: mediatek: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
$

After this patch:

$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
alias:          of:N*T*Cmediatek,mt8135-mmcC*
alias:          of:N*T*Cmediatek,mt8135-mmc

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:29 +01:00
Ulf Hansson 089d6aa64a mmc: rtsx_usb_sdmmc: Enable runtime PM autosuspend
Enable runtime PM autosuspend for the rtsx_usb_sdmmc driver to avoid the
device being runtime suspended and runtime resumed between each request.
Let's use a default timeout of 50ms, to be consistent with other mmc hosts.

Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:28 +01:00
Jaehoon Chung 273c5414e3 mmc: sdhci: put together into one condition checking
value of ios->timing is not related with SDCHI v3.0.  If Controller version
is v3.0, SDHCI_QUIRK_NO_HISPD_BIT is meaningless.  To prevent the setting
wrong bit moves into one condition checking.  (e.g sdhci-s3c doesn't use
SDHCI_CTRL_HISPD bit, instead using this bit as other purpose.)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:27 +01:00
Jaehoon Chung 647f80a1f2 mmc: dw_mmc: fix the error handling for dma operation
When dma->start is failed,then it has to fall back to PIO mode
for current transfer.

But Host controller was already set to bits relevant to DMA operation.
If needs to use the PIO mode, Host controller has to stop the DMA
operation. (It's more stable than now.)

When it occurred error, it's not running any request.

Fixes: 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface support")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-21 11:08:28 +01:00
Michael Walle b0921d5c9e mmc: sdhci-of-esdhc: fixup PRESENT_STATE read
Since commit 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
  mmc0: Card stuck in programming state! __mmc_switch
  mmc0: error -110 whilst initialising MMC card

Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.

Signed-off-by: Michael Walle <michael@walle.cc>
Fixes: 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-18 14:41:47 +01:00
Fabio Estevam f91346e8b5 mmc: mxs: Initialize the spinlock prior to using it
An interrupt may occur right after devm_request_irq() is called and
prior to the spinlock initialization, leading to a kernel oops,
as the interrupt handler uses the spinlock.

In order to prevent this problem, move the spinlock initialization
prior to requesting the interrupts.

Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-07 13:30:08 +01:00
Ulf Hansson fe1b5700c7 mmc: mmc: Use 500ms as the default generic CMD6 timeout
In the eMMC 4.51 version of the spec, an EXT_CSD field called
GENERIC_CMD6_TIME[248] was added. This allows cards to specify the maximum
time it may need to move out from its busy state, when a CMD6 command has
been sent.

In cases when the card is compliant to versions < 4.51 of the eMMC spec,
obviously the core needs to use a fall-back value for this timeout, which
currently is set to 10 minutes. This value is completely in the wrong range
and importantly in some cases it causes a card initialization to take more
than 10 minute to complete.

Earlier this scenario was avoided as the mmc core used CMD13 to poll the
card, to find out when it stopped signaling busy. Commit 08573eaf1a
("mmc: mmc: do not use CMD13 to get status after speed mode switch")
changed this behavior.

Instead of reverting that commit, which would cause other issues, let's
instead start by picking a simple solution for the problem, by using a
500ms default generic CMD6 timeout.

The reason for using exactly 500ms, comes from observations that shows it's
quite common for cards to specify 250ms. 500ms is two times that value so
likely it should be enough for most cards.

Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 08573eaf1a ("mmc: mmc: do not use CMD13 to get status after speed
mode switch")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-07 13:29:52 +01:00
Adrian Hunter be55f7bee3 mmc: mmc_test: Fix "Commands during non-blocking write" tests
mmc_test_check_result_async() requires that struct mmc_async_req is
contained within struct mmc_test_async_req. Fix the "Commands during
non-blocking write" tests so that is the case.

Fixes: 4bbb9aac9a ("mmc: mmc_test: Add tests for sending commands during transfer")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-07 13:28:38 +01:00
Adrian Hunter 086b0ddbef mmc: sdhci: Fix missing enhanced strobe setting during runtime resume
Restore enhanced strobe setting during runtime resume.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-07 13:26:43 +01:00
Adrian Hunter fe5fb2e3b5 mmc: sdhci: Reset cmd and data circuits after tuning failure
To prevent subsequent commands failing, ensure the cmd and data circuits
are reset after a tuning timeout.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-07 13:26:43 +01:00
Adrian Hunter 69b962a65a mmc: sdhci: Fix unexpected data interrupt handling
In the busy response case (i.e. !host->data), an unexpected data interrupt
would result in clearing the data command as though it had completed but
without informing the upper layers and thus resulting in a hang.  Fix by
only clearing the data command for data interrupts that are expected.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-07 13:26:42 +01:00
Adrian Hunter 6ebebeab51 mmc: sdhci: Fix CMD line reset interfering with ongoing data transfer
CMD line reset during an ongoing data transfer can cause the data transfer
to hang.  Fix by delaying the reset until the data transfer is finished.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-07 13:26:42 +01:00
Jaehoon Chung 3a667e3ff7 mmc: dw_mmc: add the "reset" as name of reset controller
Add the "reset" as name of reset controller.
This is for preventing the wrong operation. Even if some SoC has reset
controller, doesn't define "resets" in device-tree.
Then it might be waiting for reset controller and it should be stuck.

Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-07 08:53:46 +01:00
Christoph Hellwig e806402130 block: split out request-only flags into a new namespace
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.

This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests.  It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-28 08:45:17 -06:00
Wei Yongjun d1f63f0c81 mmc: sdhci-msm: Fix error return code in sdhci_msm_probe()
Fix to return a negative error code from the platform_get_irq_byname()
error handling case instead of 0, as done elsewhere in this function.

Fixes: ad81d38710 ("mmc: sdhci-msm: Add support for UHS cards")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-27 09:43:01 +02:00
Jaehoon Chung 45c7a4908a mmc: dw_mmc-pltfm: fix the potential NULL pointer dereference
platform_get_resource can be returned the NULL pointer.
Then regs->start should be referred to NULL Pointer.
devm_ioremap_resource() checks whether res is NULL or not.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-25 10:39:40 +02:00
Ulf Hansson 4f48aa7a11 mmc: rtsx_usb_sdmmc: Handle runtime PM while changing the led
Accesses of the rtsx sdmmc's parent device, which is the rtsx usb device,
must be done when it's runtime resumed. Currently this isn't case when
changing the led, so let's fix this by adding a pm_runtime_get_sync() and
a pm_runtime_put() around those operations.

Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-17 15:43:03 +02:00
Ulf Hansson 31cf742f51 mmc: rtsx_usb_sdmmc: Avoid keeping the device runtime resumed when unused
The rtsx_usb_sdmmc driver may bail out in its ->set_ios() callback when no
SD card is inserted. This is wrong, as it could cause the device to remain
runtime resumed when it's unused. Fix this behaviour.

Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-17 15:42:25 +02:00
Haibo Chen 02265cd603 mmc: sdhci: cast unsigned int to unsigned long long to avoid unexpeted error
Potentially overflowing expression 1000000 * data->timeout_clks with
type unsigned int is evaluated using 32-bit arithmetic, and then used
in a context that expects an expression of type unsigned long long.

To avoid overflow, cast 1000000U to type unsigned long long.
Special thanks to Coverity.

Fixes: 7f05538af7 ("mmc: sdhci: fix data timeout (part 2)")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-17 15:16:20 +02:00
Aaron Brice 77da3da0b2 mmc: sdhci-esdhc-imx: Correct two register accesses
- The DMA error interrupt bit is in a different position as
   compared to the sdhci standard.  This is accounted for in
   many cases, but not handled in the case of clearing the
   INT_STATUS register by writing a 1 to that location.
 - The HOST_CONTROL register is very different as compared to
   the sdhci standard.  This is accounted for in the write
   case, but not when read back out (which it is in the sdhci
   code).

Signed-off-by: Dave Russell <david.russell@datasoft.com>
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-13 08:58:03 +02:00
Adrian Hunter fee686b74a mmc: sdhci-pci: Fix bus power failing to enable for some Intel controllers
Some Intel controllers (e.g. BXT) might fail to set bus power after a
D3 -> D0 transition due to the present state not yet having propagated.
Retry for up to 2 milliseconds.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:20:52 +02:00
Adrian Hunter 6bc090631d mmc: sdhci-pci: Let devices define their own sdhci_ops
Let devices define their own sdhci_ops so that device-specific variations
can be implemented without adding quirks.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:20:48 +02:00
Adrian Hunter 606d313124 mmc: sdhci: Rename sdhci_set_power() to sdhci_set_power_noreg()
Unlike other cases, sdhci_set_power() does not reflect the default
implementation of the ->set_power() callback. Rename it and create
sdhci_set_power() that is the default implementation.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:20:41 +02:00
Adrian Hunter fc605f1d80 mmc: sdhci: Fix SDHCI_QUIRK2_STOP_WITH_TC
Multi-block data transfers can specify the number of blocks either using a
Set Block Count command (CMD23) or by sending a STOP command (CMD12) after
the required number of blocks has transferred. CMD23 is preferred, but some
cards don't support it. CMD12 with R1b response is used for writes, and
R1 response for reads.

Some SDHCI host controllers give a Transfer Complete (TC) interrupt for the
STOP command (CMD12) whether or not a R1b response has been specified. The
quirk SDHCI_QUIRK2_STOP_WITH_TC identifies those host controllers, but the
implementation only considers the case where the TC interrupt arrives at
the same time as the Command Complete (CC) interrupt. However,
occasionally TC arrives before CC. That is harmless, but does generate an
error message "Got data interrupt 0x00000002 even though no data operation
was in progress".

A simpler approach is to force R1b response onto all STOP commands, because
SDHCI will handle TC before CC in the general case, so do that.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:20:34 +02:00
Jiri Slaby 3f2d266435 mmc: core: Annotate cmd_hdr as __le32
Commit f68381a70b (mmc: block: fix packed command header endianness)
correctly fixed endianness handling of packed_cmd_hdr in
mmc_blk_packed_hdr_wrq_prep.

But now, sparse complains about incorrect types:
drivers/mmc/card/block.c:1613:27: sparse: incorrect type in assignment (different base types)
drivers/mmc/card/block.c:1613:27:    expected unsigned int [unsigned] [usertype] <noident>
drivers/mmc/card/block.c:1613:27:    got restricted __le32 [usertype] <noident>
...

So annotate cmd_hdr properly using __le32 to make everyone happy.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: f68381a70b (mmc: block: fix packed command header endianness)
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:14:49 +02:00
Shawn Lin 8a3bee9b13 mmc: sdhci-of-arasan: add sdhci_arasan_voltage_switch for arasan, 5.1
Per the vendor's requirement, we shouldn't do any setting for
1.8V Signaling Enable, otherwise the interaction/behaviour between
phy and controller will be undefined. Mostly it works fine if we do
that, but we still see failures. Anyway, let's fix it to meet the
vendor's requirement. The error log looks like:

 [   93.405085] mmc1: unexpected status 0x800900 after switch
 [   93.408474] mmc1: switch to bus width 1 failed
 [   93.408482] mmc1: mmc_select_hs200 failed, error -110
 [   93.408492] mmc1: error -110 during resume (card was removed?)
 [   93.408705] PM: resume of devices complete after 213.453 msecs

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:01:33 +02:00
Shawn Lin 4f25580fb8 mmc: core: changes frequency to hs_max_dtr when selecting hs400es
Per JESD84-B51 P49, Host need to change frequency to <=52MHz
after setting HS_TIMING to 0x1, and host may changes frequency
to <= 200MHz after setting HS_TIMING to 0x3. That means the card
expects the clock rate to increase from the current used f_init
(which is less than 400KHz, but still being less than 52MHz) to
52MHz, otherwise we find some eMMC devices significantly report
failure when sending status.

Reported-by: Xiao Yao <xiaoyao@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:01:15 +02:00