This is just an additional analog board configuration.
Signed-off-by: Mikhail Fedotov <mo_fedotov.mail.ru>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver supports analog TV, radio and DVB-T.
It is based on the preliminary patch by Pierluigi Rolando.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A bug in cx8802_get_driver() meant that in multiboard environments, when testing
frontends on the non primary board, the incorrect device was returned resulting
in "Unsupported value in .mpeg.." messages. Depending on the electrical design
of the hardware (serial, parallel, rising/falling edge detect), transport would
still be delivered and the problem went unnoticed.
This patch ensures the correct instance of cx8802_dev is returned.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A series of patches to change the cx88 framework to allow the
PCI mpeg port to be shared dynamically between different
types of drivers or applications. This patch changes the cx88-dvb
and cx88-blackbird drivers to become 'sub drivers' of a higher
single cx88-mpeg driver.
The cx88-mpeg driver is a superset of the previous cx88-mpeg/blackbird
drivers and now owns the IRQ. cx88-dvb/blackbird now become mini drivers,
registering themselves with cx88-mpeg through a standard interface with
callbacks.
Sub drivers request access to hardware via the cx88-mpeg driver. In turn
the cx88-mpeg driver determines whether the hardware is busy and accepts
or refuses the request, grant access using callbacks into the sub drivers.
The net effect is that you are no longer able to tamper with the mpeg port
from multiple different applications at the same time, potentially breaking
a live mpeg2 hardware encoding or dvb stream.
The mechanism extends to enable multiple dvb frontends to be registered
and share the single resource.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Initial commit for the driver for the DiB7000M COFDM demodulator.
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the advanced debugging ioctls, to allow access to the
cx88 registers from userspace. Only i2c_id == 0 is supported, for access
to the cx88 adapter itself. There isn't any support for access to I2C
clients of the adapter. Most of them don't have R/W registers anyway,
and its necessary to use i2c-dev to talk to them from userspace.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: no paravirt for X86_VOYAGER or X86_VISWS
[PATCH] i386: Fix io_apic.c warning
[PATCH] i386: export smp_num_siblings for oprofile
[PATCH] x86: Work around gcc 4.2 over aggressive optimizer
[PATCH] x86: Fix boot hang due to nmi watchdog init code
[PATCH] x86: Fix verify_quirk_intel_irqbalance()
[PATCH] i386: Update defconfig
[PATCH] x86-64: Update defconfig
Since Voyager and Visual WS already define ARCH_SETUP,
it looks like PARAVIRT shouldn't be offered for them.
In file included from arch/i386/kernel/setup.c:63:
include/asm-i386/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefin=
ed
In file included from include/asm/msr.h:5,
from include/asm/processor.h:17,
from include/asm/thread_info.h:16,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/capability.h:45,
from include/linux/sched.h:46,
from arch/i386/kernel/setup.c:26:
include/asm/paravirt.h:163:1: warning: this is the location of the previous=
definition
In file included from arch/i386/kernel/setup.c:63:
include/asm-i386/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefin=
ed
In file included from include/asm/msr.h:5,
from include/asm/processor.h:17,
from include/asm/thread_info.h:16,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/capability.h:45,
from include/linux/sched.h:46,
from arch/i386/kernel/setup.c:26:
include/asm/paravirt.h:163:1: warning: this is the location of the previous=
definition
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
gcc 4.2 warns
linux/arch/i386/kernel/io_apic.c: In function ‘create_irq’:
linux/arch/i386/kernel/io_apic.c:2488: warning: ‘vector’ may be used uninitialized in this function
The warning is false, but somewhat legitimate so work around it.
Signed-off-by: Andi Kleen <ak@suse.de>
oprofile uses smp_num_siblings without testing for CONFIG_X86_HT.
I looked at modifying oprofile, but this way is cleaner & simpler
and I didn't see a good reason not to just export it when CONFIG_SMP.
WARNING: "smp_num_siblings" [arch/i386/oprofile/oprofile.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The new PDA code uses a dummy _proxy_pda variable to describe
memory references to the PDA. It is never referenced
in inline assembly, but exists as input/output arguments.
gcc 4.2 in some cases can CSE references to this which causes
unresolved symbols. Define it to zero to avoid this.
Signed-off-by: Andi Kleen <ak@suse.de>
2.6.19 stopped booting (or booted based on build/config) on our x86_64
systems due to a bug introduced in 2.6.19. check_nmi_watchdog schedules an
IPI on all cpus to busy wait on a flag, but fails to set the busywait
flag if NMI functionality is disabled. This causes the secondary cpus
to spin in an endless loop, causing the kernel bootup to hang.
Depending upon the build, the busywait flag got overwritten (stack variable)
and caused the kernel to bootup on certain builds. Following patch fixes
the bug by setting the busywait flag before returning from check_nmi_watchdog.
I guess using a stack variable is not good here as the calling function could
potentially return while the busy wait loop is still spinning on the flag.
AK: I redid the patch significantly to be cleaner
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix verify_quirk_intel_irqbalance(). genapic checks should really
happen only on affected versions of the E7520/E7320/E7525 based platforms.
AK: This should akpm's Coyote SDV
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (21 commits)
Fix http://bugzilla.kernel.org/show_bug.cgi?id=7606
drm: add flag for mapping PCI DMA buffers read-only.
drm: fix up irqflags in drm_lock.c
drm: i915 updates
drm: i915: fix up irqflags arg
drm: i915: Only return EBUSY after we've established we need to schedule a new swap.
drm: i915: Fix 'sequence has passed' condition in i915_vblank_swap().
drm: i915: Add SAREA fileds for determining which pipe to sync window buffer swaps to.
drm: Make handling of dev_priv->vblank_pipe more robust.
drm: DRM_I915_VBLANK_SWAP ioctl: Take drm_vblank_seq_type_t instead
drm: i915: Add ioctl for scheduling buffer swaps at vertical blanks.
drm: Core vsync: Don't clobber target sequence number when scheduling signal.
drm: Core vsync: Add flag DRM_VBLANK_NEXTONMISS.
drm: Make locked tasklet handling more robust.
drm: drm_rmdraw: Declare id and idx as signed so testing for < 0 works as intended.
drm: Change first valid DRM drawable ID to be 1 instead of 0.
drm: drawable locking + memory management fixes + copyright
drm: Add support for interrupt triggered driver callback with lock held to DRM core.
drm: Add support for tracking drawable information to core
drm: add support for secondary vertical blank interrupt to i915
...
Use direct assignment rather than cmpxchg() as the latter is unavailable
and unimplementable on some platforms and is actually unnecessary.
The use of cmpxchg() was to guard against two possibilities, neither of
which can actually occur:
(1) The pending flag may have been unset or may be cleared. However, given
where it's called, the pending flag is _always_ set. I don't think it
can be unset whilst we're in set_wq_data().
Once the work is enqueued to be actually run, the only way off the queue
is for it to be actually run.
If it's a delayed work item, then the bit can't be cleared by the timer
because we haven't started the timer yet. Also, the pending bit can't be
cleared by cancelling the delayed work _until_ the work item has had its
timer started.
(2) The workqueue pointer might change. This can only happen in two cases:
(a) The work item has just been queued to actually run, and so we're
protected by the appropriate workqueue spinlock.
(b) A delayed work item is being queued, and so the timer hasn't been
started yet, and so no one else knows about the work item or can
access it (the pending bit protects us).
Besides, set_wq_data() _sets_ the workqueue pointer unconditionally, so
it can be assigned instead.
So, replacing the set_wq_data() with a straight assignment would be okay
in most cases.
The problem is where we end up tangling with test_and_set_bit() emulated
using spinlocks, and even then it's not a problem _provided_
test_and_set_bit() doesn't attempt to modify the word if the bit was
set.
If that's a problem, then a bitops-proofed assignment will be required -
equivalent to atomic_set() vs other atomic_xxx() ops.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove bogus comments about unexporting cache_{push,clear}(), as inline
dma_cache_maintenance() (used by at least bionet and pamsnet) calls them.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Atari IDE: The interrupt needs SA_SHIRQ now to get registered.
Signed-off-by: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sun3 scsi drivers compile/work again (though with way too many warnings...)
Tested on 3/50, 3/60.
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
General compile fixes for 2.6.16 for sun3, and some updates to make the new
bootloader work correctly. Tested on 3/50, 3/60, 3/80.
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- 7990: request_irq() should have SA_SHIRQ flag set
- hplance_init() printed dev->name before register_netdev() had filled it in
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETLINK]: Put {IFA,IFLA}_{RTA,PAYLOAD} macros back for userspace.
[NET_SCHED] sch_htb: turn intermediate classes into leaves
[NET_SCHED] sch_cbq: deactivating when grafting, purging etc.
[XFRM]: Fix XFRMGRP_REPORT to use correct multicast group.
[NET]: Force a cache line split in hh_cache in SMP.
[NETPOLL]: make arp replies through netpoll use mac address of sender
[NETLINK]: Restore API compatibility of address and neighbour bits
[AX.25]: Fix default address and broadcast address initialization.
[AX.25]: Constify ax25 utility functions
[BNX2]: Add an error check.
[NET]: Convert hh_lock to seqlock.
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[PATCH] add STB810 support (Philips PNX8550-based)
[MIPS] Qemu now has an ELF loader.
[MIPS] Add GENERIC_HARDIRQS_NO__DO_IRQ for i8259 users
[MIPS] Optimize csum_partial for 64bit kernel
[MIPS] Optimize flow of csum_partial
[MIPS] Make csum_partial more readable
[MIPS] Rename SNI_RM200_PCI to just SNI_RM preparing for more RM machines
GLIBC uses them etc.
They are guarded by ifndef __KERNEL__ so nobody will start
accidently using them in the kernel again, it's just for
userspace.
Signed-off-by: David S. Miller <davem@davemloft.net>
- turn intermediate classes into leaves again when their
last child is deleted (struct htb_class changed)
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
- deactivating of active classes when q.qlen drops to zero
(cbq_drop)
- a redundant instruction removed from cbq_deactivate_class
PS: probably htb_deactivate in htb_delete and
cbq_deactivate_class in cbq_delete are also
redundant now.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRMGRP_REPORT uses 0x10 which is a group that belongs
to events. The correct value is 0x20.
We should really be using xfrm_nlgroups going forward; it was tempting
to delete the definition of XFRMGRP_REPORT but it would break at
least iproute2.
Signed-off-by: J Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
hh_lock was converted from rwlock to seqlock by Stephen.
To have a 100% benefit of this change, I suggest to place read mostly fields
of hh_cache in a separate cache line, because hh_refcnt may be changed quite
frequently on some busy machines.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in 2.4 arp requests that were recevied by netpoll were processed
in netconsole_receive_skb, where they were responded to using the src
mac of the request sender. In the 2.6 kernel arp_reply is responsible
for this function, but instead of using the src mac address of the
incomming request, the stored mac address that was registered for the
netconsole application is used. While this is usually ok, it can lead
to failures in netpoll in some situations (specifically situations
where a network may have two gateways, as arp requests from one may be
responded to using the mac address of the other). This patch reverts
the behavior to what we had in 2.4, in which all arp requests are sent
back using the src address of the request sender.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore API compatibility due to bits moved from rtnetlink.h to
separate headers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the callsign but not the SSID part of an AX.25 address is ASCII
based but Linux by initializes the SSID which should be just a 4-bit
number from ASCII anyway.
Fix that and convert the code to use a shared constant for both default
addresses. While at it, use the same style for null_ax25_address also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a missing error check spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hard header cache is in the main output path, so using
seqlock instead of reader/writer lock should reduce overhead.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that i8259A_chip uses new irq flow handler select
GENERIC_HARDIRQS_NO__DO_IRQ on some more platforms.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Delete dead codes at end of the function and move small_csumcopy
there. This makes some labels (maybe_end_cruft, small_memcpy,
end_bytes, out) needless and eliminates some branches.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use standard o32 register name instead of T0, T1, etc, like memcpy.S.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Poison init section before freeing it.
[S390] Use add_active_range() and free_area_init_nodes().
[S390] Virtual memmap for s390.
[S390] Update documentation for dynamic subchannel mapping.
[S390] Use dev->groups for adding/removing the subchannel attribute group.
[S390] Support for disconnected devices reappearing on another subchannel.
[S390] subchannel lock conversion.
[S390] Some preparations for the dynamic subchannel mapping patch.
[S390] runtime switch for qdio performance statistics
[S390] New DASD feature for ERP related logging
[S390] add reset call handler to the ap bus.
[S390] more workqueue fixes.
[S390] workqueue fixes.
[S390] uaccess_pt: add missing down_read() and convert to is_init().
This modifies Makefiles and Kconfigs to properly reflect the creation of
generic HID layer.
It also removes the dependency of BROKEN, which was introduced by the
first patch in series (see the comment). Also updates credits.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pb_fnmode parameter has to be passed to usbhid, both for compatibility reasons
and also because it logically belongs there.
Also removes empty hid-input.c file in drivers/usb/input.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hid_input_report() was needlessly USB-specific in USB HID. This patch
makes the function independent of HID implementation and fixes all
the current users. Bluetooth patches comply with this prototype.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- hiddev is USB-only (agreed with Marcel Holtmann that Bluetooth currently
doesn't need it, and future planned interface (rawhid) will be more flexible
and usable)
- both HID and USB-hid can be now compiled as modules (wasn't possible before
hiddev was fully separated from generic HID layer)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mikhail Fedotov