It was observed that after module removal followed by insertion,
the SW mode chipselect is not properly set. Thus causing transfer
failure due to incorrect CS toggling.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is to fix the SPI DMA transfer failure for speed less than 1M.
If using current DMA burst size setting (16), the Rx data bytes are
invalid due to each data byte is multiplied according to the burst
size setting.
Let's said supposedly we shall receive the following 18 bytes of data:
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18
Instead, the data bytes received consist of "16 bytes of '01' +
2 bytes of '02'" :
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 02 02
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extract the common parts of rspi_transfer_one(), rspi_rz_transfer_one(),
and qspi_transfer_out_in() into the new function rspi_common_transfer().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for RSPI on r7s72100 (RZ/A1H).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for QSPI on R-Car Gen2, for Single, Dual, and Quad SPI
Transfers.
Performance figures for reading from a QSPI FLASH driven at 24.375 MHz
on r8a7791/koelsch:
- Single: 1.1 Mbps PIO, 23 Mbps DMA
- Dual : 12.7 Mbps PIO, 48 Mbps DMA
- Quad : 13 Mbps PIO, 70 Mbps DMA
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_send_dma() and rspi_send_receive_dma() are very similar. Consolidate
into a single function rspi_dma_transfer(), and add missing checks for
dmaengine_submit() failures.
Both sg_table pointer parameters can be NULL, as RSPI supports TX-only
mode, and unidirectional DMA transfers will also be needed later for
Dual/Quad DMA support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA routines only need access to the scatter-gather tables inside the
spi_transfer structures, hence just pass those.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Refactor RSPI (on SH) DMA handling to make it reusable for other RSPI
implementations:
- Call the DMA routines after configuring the TX Mode bit and after
calling rspi_receive_init(), so these RSPI-specific operations can be
removed from the DMA routines,
- Absorb rspi_transfer_out_in() into rspi_transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the SPI core DMA mapping framework instead of our own.
If available, DMA is used for transfers larger than the FIFO size
(8 or 32 bytes).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI DMA core framework needs both RX and TX DMA to function. As a
preparation for converting the driver to use this framework, fall back to
PIO if no DMA channel or only one DMA channel is available.
This affects only RSPI, which could do DMA transfers for TX-only before.
RSPI-RZ and QSPI (at least for Single SPI Transfers) will need both RX and
TX DMA anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The resource is know to exist, as rspi_probe() already mapped it.
Remove the test, and just pass the resource.
Pass the device pointer instead of the platform device pointer, as the
latter is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Setup of the receive and transmit DMA channels is very similar, so let's
consolidate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fall back to PIO if DMA configuration failed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The various PIO loops are very similar. Consolidate into a single
function rspi_pio_transfer().
Both buffer pointers can be NULL, as RSPI supports TX-only mode, and
Dual/Quad SPI Transfers are unidirectional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
RSPI needs dummy transfers to generate the SPI clock on receive.
RSPI-RZ and QSPI always do both transmit and receive.
Use the SPI core SPI_MASTER_MUST_RX/SPI_MASTER_MUST_TX infrastructure
instead of checking for the presence of buffers and providing dummy data
ourselves (for PIO), or providing a dummy buffer (for DMA).
rspi_receive_dma() now provides full duplex DMA transfers on RSPI, and is
renamed to rspi_send_receive_dma().
As the SPI core will always provide a TX buffer, the logic to choose
between DMA send and DMA send/receive in rspi_transfer_one() now has to
check for the presence of an RX buffer. Likewise for the DMA availability
tests in rspi_is_dma().
The buffer tests in qspi_transfer_one() are now always true, so they're
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 16-bit DMA support doesn't fit well within the SPI core DMA framework,
as it needs to manage its own double-sized temporary buffers, for handling
the interleaved data.
Remove it, as there is no in-tree board code that sets
rspi_plat_data.dma_width_16bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 8449fd76de ("spi: rspi: Merge
rspi_send_pio() and rspi_receive_pio()"), rspi_receive_init() is called
for transmit-only transfers too, while this is not needed.
Only call rspi_receive_init() when receiving, to preserve behavior on
RSPI on SH.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit 7dd6278733 (spi/pxa2xx: Convert
to core runtime PM) master->auto_runtime_pm was set to true.
In this case pm_runtime_enable() must be called *before*
spi_register_master(), otherwise the kernel hangs with this error
message:
spi_master spi0: Failed to power device: -13
A similar fix, but for spi/hspi, was applied in
268d76430d.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@linaro.org>
By default for every espi transfer, the rx_buf is placed right after the
tx_buf. This can lead to a buffer overflow when the size of both the TX
and RX data cumulated is higher than the allocated 64K buffer for the
transfer (this is the case when sending for instance a read command and
reading 64K back, please see:
http://article.gmane.org/gmane.linux.drivers.mtd/53411 )
This gets fixed by always setting the RX buffer pointer at the begining
of the transfer buffer.
[The driver shouldn't be doing the copy in the first place and instead
sending directly from the supplied buffer but this is at least not worse
than what's there -- broonie]
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rejecting unsupported values of spi-tx-bus-width and spi-rx-bus-width
may break compatibility with future DTs. Just ignore them, falling back
to Single SPI Transfers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The calculation of the bit rate divider used a standard C division, which
rounds down the quotient. This may lead to a higher bitrate than requested.
Round up to avoid this.
E.g. on Koelsch, the SPI flash (configured for 30 MHz) was driven at 48.75
MHz. After this patch it's driven at a safe 24.375 MHz.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
current PIO tranfer method be described as follows:
1. fill as much as bytes but no more than 256 bytes(fifo size)
2. enable oflow/uflow/txfifo_empty interrupt
3. isr process 3 interrupt signal, do complete works.
4. after isr done, if there are left bytes go into 1 else go into 5
5. transfer end
by current PIO transfer method:
1. reduce interrupt counts in spi interrupt line.
2. reduce interrupt latency because no do data fill/fetch in isr.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The spi-topcliff-pch driver is for a companion chip to the Intel Atom
E600 series processors. These are 32-bit x86 processors so the driver
is only needed on X86_32. Add COMPILE_TEST as an alternative, so that
the driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the calculation for determining whether to use FIFO or BLOCK
mode.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case we are doing DMA transfer and the size of the buffer is not multiple
of 4 bytes the driver truncates that to 4-byte boundary and tries to handle
remaining bytes using PIO.
Or that is what it tried to do. What actually happens is that it calls
ALIGN() to the buffer size which aligns it to the next 4-byte boundary
(doesn't truncate). Doing this results 1-3 bytes extra to be transferred.
Furthermore we handle remaining bytes using PIO which results one extra
byte to be transferred. In worst case the driver transfers 4 extra bytes.
While investigating this it turned out that the DMA hardware doesn't even
have such limitation so we can solve this by dropping the code that tries
to handle unaligned bytes.
Reported-by: Chiau Ee Chew <chiau.ee.chew@intel.com>
Reported-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The dw_spi_cleanup() function was removed by commit c63f5da008
"spi: dw: Don't call kfree for memory allocated by devm_kzalloc".
commit ec37e8e1f0 "spi: dw: migrate to generic queue infrastructure" added
dw_spi_cleanup() but never use it. So now I got below build warning:
CC [M] drivers/spi/spi-dw.o
drivers/spi/spi-dw.c:609:13: warning: 'dw_spi_cleanup' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Found using smatch:
drivers/spi/spi-atmel.c:878 atmel_spi_pump_pio_data() warn: unsigned
'as->current_remaining_bytes' is never less than zero.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we fail to create the master queue for some reason we should not attempt
to clean it up since attempting to stop a kthread that was not created will
hang and it's just generally bad practice. Unfortunately at present we call
spi_destroy_queue() even in cases where the creation fails.
Fix this by fixing the error handling in spi_master_initialize_queue() so
that we only flag the master as queued or destroy the queue if creation
succeeded. The change to the flag is done since the general master
cleanup uses this to destroy the queue.
Reported-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
If NO_DMA=y:
drivers/built-in.o: In function `spi_map_buf':
spi.c:(.text+0x21bc60): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `spi_unmap_buf.isra.33':
spi.c:(.text+0x21c32e): undefined reference to `dma_unmap_sg'
make[3]: *** [vmlinux] Error 1
Protect the DMA code by #ifdef CONFIG_HAS_DMA to fix this:
- Extract __spi_map_msg() from spi_map_msg(),
- Provide dummy definitions of __spi_map_msg() and spi_unmap_msg() if
!CONFIG_HAS_DMA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also, use this opportunity to let spi_chip_sel() handle chip-select
deactivation as well.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
The availability of SPI Dual or Quad Transfer Mode as indicated by the
"spi-tx-bus-width" and "spi-rx-bus-width" properties in the device tree is
a hardware property of the SPI master, SPI slave, and board wiring. Hence
the SPI core should not reject an SPI slave because an SPI master driver
doesn't (yet) support Dual or Quad Transfer Mode.
Change the lack of Dual or Quad Transfer Mode support in the SPI master
driver from an error condition to a warning condition, and ignore the
unsupported mode bits, falling back to Single Transfer Mode, to avoid
breakages when running old kernels with new device trees.
Fixes: f477b7fb13 (spi: DUAL and QUAD support)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Similar to CE4100, BayTrail LPSS SPI can be PCI enumerated
as well. Thus, the functions are renamed from ce4100_xxx
to pxa2xx_spi_pci_xxx to clarify that this is a generic
PCI glue layer. Also, added required infrastructure to
support SPI hosts with different configurations.
This patch is based on Mika Westerberg's previous work.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
atmel_spi_lock does a spin_lock_irqsave, so we need to renable the
interrupts when we want to schedule.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make FSL eSPI CSnBEF and CSnAFT fields in ESPI_SPMODEn registers
(n=0,1,2,3) configurable through device tree.
CSnBEF is the chip select setup time. It's the delay in bits from the
activation of chip select pin to the first clock for data frame.
CSnAFT is the chip select hold time. It's the delay in bits from the
last clock for data frame to the deactivation of chip select pin.
The FSL eSPI driver hardcodes CSnBEF and CSnAFT to 0. Need to set
them to a different value for some device.
Signed-off-by: Jane Wan <Jane.Wan@gainspeed.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
split sirfsoc_spi_transfer function into 3 sub-functions:
spi_sirfsoc_cmd_transfer, spi_sirfsoc_pio_transfer and
spi_sirfsoc_dma_transfer.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dependency on ARM in Kconfig.
This is to fix the build error related to _relaxed IO.
Remove dependency on SPI_MASTER because this is already defined
under if SPI_MASTER in Kconfig.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than requesting the shyway_clk call clk_get with
the device and a NULL con_id.
This is in keeping with the way that clk_get() is called
on other drivers used by Renesas Gen 1 SoCs. And I believe
it is compatible with supplying clocks via DT, unlike the current code.
It appears to me that the two uses of this driver are
the r8a7778 and r8a7779 SoCs.
The r8a7779 already has clocks setup to allow this driver to continue to work
with this change applied.
The r8a7778 has clocks incorrectly setup to allow this driver to continue
to work with this change applied. This problem is addressed in
"ARM: shmobile: r8a7778: Use clks as MSTP007 parent" which is thus
a pre-requisite of this patch.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
sometimes t->tx can be equal with t->rx. for example, spidev will make
tx and rx point to spidev->buffer at the same time. currently, for this
case, we map the buffer BIDIRECTION to fix the cache consistency.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix a lot of "line over 80 characters" checkpatch issues, on which
the users of the driver, key customers care about this very much.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
orignal GPIO chipslect is not standard because it don't take care to the
chipselect signal: BITBANG_CS_ACTIVE and BITBANG_CS_INACTIVE.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI bitbang supply "chipselect" interface for change chip-select line
, in the SiRFSoC SPI controller, we need to enable "SPI_CS_IO_MODE",
otherwise, spi_sirfsoc_chipselect() has no effect.
now the driver is working is because SPI controller will control CS
automatically without SPI_CS_IO_MODE. this patch makes the CS controller
really controlled by software.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the old code uses wrong marco - SIRFSOC_SPI_FIFO_FULL is not for
FIFO interrupt status, it is for FIFO status. here in the ISR,
SIRFSOC_SPI_TXFIFO_EMPTY is the right bit for SPI TXFIFO interrupt
status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add driver for Cadence SPI controller. This is used in Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Spi v3 controller is not only used on Blackfin. So rename it
and use ioread/iowrite api to make it work on other platform.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify the cleanup code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
mpc8xxx_spi_probe() has set master->cleanup = mpc8xxx_spi_cleanup,
however current code overrides the setting in fsl_spi_probe() and set
master->cleanup = fsl_spi_cleanup.
Thus the memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current code, master->cleanup and master->setup are not set in the same
function. This makes it hard to read and not good for code maintain.
One example is in fsl-spi.c, master->cleanup is overrided in mpc8xxx_spi_probe()
which leads to a memory leak.
This patch removes mpc8xxx_spi_cleanup() and converts fsl_espi_setup to use
devm_kzalloc so we don't need to take care of freeing memory.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
add optional property devicetree for SPI slave nodes
into devicetree so that LSB mode can be enabled by devicetree.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The existing timeout value in wait_for_completion_timeout is
calculated from the transfer length and speed with tolerance of 10msec.
This is too low because this is used for error conditions such as
hardware hang etc.
The xfer->speed_hz considered may not be the actual speed set
because the best clock divisor is chosen from a limited set such that
the actual speed <= requested speed. This will lead to timeout being
less than actual transfer time.
Considering acceptable latencies, this timeout can be set to a
value double the expected transfer plus 100 msecs.
This patch adds the same in the core.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't use unsigned for current_remaining_bytes so we can check
current_remaining_bytes < 0 case.
Use int is enough for current_remaining_bytes.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A few driver specific fixes, the main one being the fix for handling of
complete callbacks that are open coded in individual drivers to allow
callers to omit the completion. As we move things into the core that
sort of issue should become less and less common.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rgeq
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the main one being the fix for handling
of complete callbacks that are open coded in individual drivers to
allow callers to omit the completion. As we move things into the core
that sort of issue should become less and less common"
* tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Depend on ARCH_QCOM
spi: efm32: Update binding document to make "efm32,location" property optional
spi: omap2-mcspi: Convert to use devm_kcalloc
spi: Always check complete callback before calling it
Commit 8fc1b0f87d ("ARM: qcom: Split Qualcomm support into legacy and
multiplatform") removed Kconfig symbol ARCH_MSM_DT. But that commit
left one (optional) dependency on ARCH_MSM_DT untouched.
Three Kconfig symbols used to depend on ARCH_MSM_DT: ARCH_MSM8X60,
ARCH_MSM8960, and ARCH_MSM8974. These three symbols now depend on
ARCH_QCOM. So it appears this driver needs to depend on ARCH_QCOM too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This saves a few unwind code and return proper error if devm_kcalloc fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 1e25cd4729 "spi: Do not require a completion", this checking is
required to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull MIPS updates from Ralf Baechle:
- Support for Imgtec's Aptiv family of MIPS cores.
- Improved detection of BCM47xx configurations.
- Fix hiberation for certain configurations.
- Add support for the Chinese Loongson 3 CPU, a MIPS64 R2 core and
systems.
- Detection and support for the MIPS P5600 core.
- A few more random fixes that didn't make 3.14.
- Support for the EVA Extended Virtual Addressing
- Switch Alchemy to the platform PATA driver
- Complete unification of Alchemy support
- Allow availability of I/O cache coherency to be runtime detected
- Improvments to multiprocessing support for Imgtec platforms
- A few microoptimizations
- Cleanups of FPU support
- Paul Gortmaker's fixes for the init stuff
- Support for seccomp
* 'mips-for-linux-next' of git://git.linux-mips.org/pub/scm/ralf/upstream-sfr: (165 commits)
MIPS: CPC: Use __raw_ memory access functions
MIPS: CM: use __raw_ memory access functions
MIPS: Fix warning when including smp-ops.h with CONFIG_SMP=n
MIPS: Malta: GIC IPIs may be used without MT
MIPS: smp-mt: Use common GIC IPI implementation
MIPS: smp-cmp: Remove incorrect core number probe
MIPS: Fix gigaton of warning building with microMIPS.
MIPS: Fix core number detection for MT cores
MIPS: MT: core_nvpes function to retrieve VPE count
MIPS: Provide empty mips_mt_set_cpuoptions when CONFIG_MIPS_MT=n
MIPS: Lasat: Replace del_timer by del_timer_sync
MIPS: Malta: Setup PM I/O region on boot
MIPS: Loongson: Add a Loongson-3 default config file
MIPS: Loongson 3: Add CPU hotplug support
MIPS: Loongson 3: Add Loongson-3 SMP support
MIPS: Loongson: Add Loongson-3 Kconfig options
MIPS: Loongson: Add swiotlb to support All-Memory DMA
MIPS: Loongson 3: Add serial port support
MIPS: Loongson 3: Add IRQ init and dispatch support
MIPS: Loongson 3: Add HT-linked PCI support
...
The core implementation of cs_change didn't follow the documentation
which says that cs_change in the middle of the transfer means to briefly
deassert chip select, instead it followed buggy drivers which change the
polarity of chip select. Use a delay of 10us between deassert and
reassert simply from pulling numbers out of a hat.
Reported-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8-bit word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Also remove the duplicate code to test spi->mode, it is done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With devm_kzalloc, the memory is automatically freed when spi_device detach from
the bus.
Fixes: commit 43f627ac9d (spi: dw: fix memory leak on error path)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stabe@vger.kernel.org
The memory allocated for chip is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes the following coccicheck warning:
linux-2.6/drivers/spi/spi-omap-uwire.c:485:2-8: ERROR: missing iounmap; ioremap on line 471 and execution via conditional on line 481
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set highest transfer speed to master->max_speed_hz and then we can remove
hw->max_speed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch merges support for all DB1xxx and PB1xxx
boards into a single image, along with a new single defconfig
for them.
Run-tested on DB1300 and DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6577/
Patchwork: https://patchwork.linux-mips.org/patch/6659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver sets the SPI_MASTER_HALF_DUPLEX flag, so the spi core will check
transfers to ensure they are not full duplex.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no real reason why we require transfers to have a completion and
the only user of the completion now checks to see if one has been provided
before using it so stop enforcing this. This makes it more convenient for
drivers to chain multiple asynchronous transfers together.
Signed-off-by: Mark Brown <broonie@linaro.org>
If during a SPI transfer with len larger than PCH_MAX_FIFO_DEPTH and the
IRQ handler happens to be called when the transmit FIFO is already empty,
and SPSR_FI_BIT is set consequently, the message
"spi_master spi32766: pch_spi_handler_sub : Transfer is not completed"
is spammed to the systemlog, because tx_index has already increased
further due to the next bytes to be written. This case is uncritical as
new bytes have already been written.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will use spi->max_speed_hz as transfer speed if the transfer speed was
not set. So we don't need to test t->speed_hz in mcfqspi_transfer_one().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch removes <mach/hardware.h> dependency. This is performed
by replace hard coded used memory regions and interrupt to getting
these values from resources passed to the driver. For the system-wide
registers we now able to use SYSCON driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure all registered platform devices are unregistered on probe() error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The definition of struct altera_spi_platform_data does not exist in current
tree. So remove the code to get platform_data which is never used.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_mpc8xxx_spi_probe() allocates memory for pinfo but the memory is not freed
anywhere. of_mpc8xxx_spi_probe() is called in .probe() and pinfo should be
freed in .remove(), so convert kzalloc to devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps increasing build testing coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The correct way to set multiple bits settings is always clear these
bit fields before set new settings.
Current code does not cause problem because the reset value of these
bit fields are 0, and these settings only set once during probe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix printk format warning by using %p extension 'ad' for dma_addr_t.
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Wformat]
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The tnetv107x platform is getting removed, so this driver
will not be needed any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When xfer->speed_hz is greater than master->max_speed_hz, it's generally safe
to use master->max_speed_hz as transfer speed.
Thus use master->max_speed_hz as transfer speed rather than return error when
xfer->speed_hz > master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
While reviewing an i2c driver for efm32 that needs a similar property
Wolfram Sang pointed out that "location" is a too generic name for
something that is efm32 specific. So add an appropriate namespace and
fall back to the generic name in case of failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If sp->info is NULL, we will hit NULL pointer dereference in probe() while
setting bus_num and num_chipselect for master:
sp->bitbang.master->bus_num = sp->info->bus_num;
sp->bitbang.master->num_chipselect = sp->info->num_chipselect;
Thus add NULL test for sp->info in probe() to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is required since commit 2025172e32 "spi/bitbang: Use core message pump".
spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/
spi_master_resume to stop/start the queue while suspend/resume.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver does not work for bits_per_word greater than 16.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already has NULL test for master after calling spi_alloc_master().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same logic in spi_clps711x_setup_xfer() and
spi_clps711x_transfer_one().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
This patch also remove testing if hz is 0 because spi->max_speed_hz will be
default set to master->min_speed_hz if it was not set. So the transfer speed
will never set to 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This simple SPI master controller is built into xtfpga bitstreams. It
always transfers 16 bit words in SPI mode 0, automatically asserting CS
on transfer start and deasserting on end.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a DT-only driver, so remove all non-DT paths.
of_gpio_named_count() may fail, thus also add checking it's return value.
efm32_spi_probe_dt() never fails, make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If pdata->cs_control is NULL, we will hit NULL pointer dereference in
mcfqspi_cs_select() and mcfqspi_cs_deselect(). Thus add NULL test for
pdata->cs_control in probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The label argument was removed by commit 989847967c
spi: clps711x: Use devm_gpio_request(), add it back.
This makes it easier to know the gpio usage in /sys/kernel/debug/gpio.
Also remove unnecessary gpio_is_valid() checking, devm_gpio_request() returns
error if the requested gpio is invalid.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This ensures clock has been enabled before calling spi_master_resume().
while at it, also add checking return value of spi_master_suspend and
spi_master_resume because they may fail.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
mmap resource requirement is only for memory mapped operations.
If the user does not populate mmap resource, dont call return,
instead we go on for normal spi mode operations.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is required since commit 2025172e32 "spi/bitbang: Use core message pump".
spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/
spi_master_resume to start/stop the queue while suspend/resume.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously only the resources controlled by the driver were put into
low power state at system suspend. Both the amba bus and a potential
power domain were ignored.
Moreover, while putting the device into low power state we first
brought it back to full power, but for no particular reason.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch issues.
ERROR: space prohibited after that open parenthesis '('
ERROR: space required before the open parenthesis '('
ERROR: trailing statements should be on next line
ERROR: space required after that ',' (ctx:VxV)
ERROR: spaces required around that '-=' (ctx:VxV)
WARNING: sizeof *cs should be sizeof(*cs)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The PM callbacks implemented by the spi-atmel driver don't call
spi_master_{resume,suspend}, fix that.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to use default implementation of transfer_one_message().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
dev_get_drvdata() returns the address of master rather than mcfqspi.
Fixes: af361079 (spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Current code set platform drvdata to dspi. However, the code in dspi_suspend()
and dspi_resume() assumes the drvdata is the address of master.
Fix it by setting platform drvdata to master.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Amend the spi atmel pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an spitransfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Zero length transfer becomes invalid since
"spi: core: Validate length of the transfers in message" commit,
but it should be valid to support an odd device, for example, which
requires long delay between chipselect and the first transfer, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same logic in spi_xcomm_setup_transfer().
Also remove a redundant code to initialize is_first variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 'ath79_spi_setup_cs' function initializes the chip
select line of a given SPI device in order to make sure
that the device is inactive.
If the SPI_CS_HIGH bit is set for a given device, it
means that the CS line of that device is active HIGH
so it must be set to LOW initially. In case of GPIO
CS lines, the 'ath79_spi_setup_cs' function does the
opposite of that due to the wrong GPIO flags.
Fix the code to use the correct GPIO flags.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Set master->max_speed_hz then spi core will handle checking transfer speed.
So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz then spi core will handle checking transfer speed.
The behavior is different from current code when the speed_hz is greater than
the maximum transfer speed supported by the controller.
Unless there is other good reason, I think we had better make the behavior
consistent with what spi core does.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses struct octeon_spi_setup to store max_speed_hz, chip_select and
mode settings of current spi device.
We can always get the same settings in octeon_spi_do_transfer() by msg->spi.
So this patch removes struct octeon_spi_setup and octeon_spi_setup,
octeon_spi_cleanup functions.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
there are many SPI clients which use the following protocal:
step 1: send command bytes to clients(rx buffer is empty)
step 2: send data bytes to clients or receive data bytes from
clients.
SiRFprimaII provides a shortcut for this kind of SPI transfer.
when tx buf is less or equal than 4 bytes and rx buf is null
in a transfer, we think it as 'command' data and use hardware
command register for the transfer.
here we can save some CPU loading than doing both tx and rx
for a normal transfer.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same implementation in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will use spi device's max
speed as default transfer speed if it is not set for this transfer.
So we can remove the same logic in hspi_hw_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, at module removal, one gets the following warnings:
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx])
[<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996300 ]---
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx])
[<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996301 ]---
Since commit 9e556dcc55, "spi: spi-imx: only
enable the clocks when we start to transfer a message", clocks are always
disabled except when transmitting messages. There is thus no need to
disable them at module removal.
Fixes: 9e556dcc55 (spi: spi-imx: only enable the clocks when we start to transfer a message)
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
hspi_cleanup() is doing nothing except print a non-useful debug message,
so remove it. Also remove unused hspi2info macro.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only remaining feature of spi-bitbang used by this driver is the
chipselect() callback, which just does conditional GPIO.
This is handled fine by the SPI core's spi_set_cs(), hence switch the
driver to use the core message handling through our own transfer_one()
method.
As the (optional) GPIO CS is no longer deasserted at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Remove the call to spi_master_put() in sh_msiof_spi_remove(), as our SPI
master is now registered using devm_spi_register_master()
(spi_bitbang_start() uses the non-managed version).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so the spi core will reject transfers that attempt
to use an unsupported bits_per_word value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move clock management and pin configuration from the bitbang chipselect()
method to the SPI core prepare_message() and unprepare_message() methods.
As spi_master.{,un}prepare_message() is guaranteed to be called in
matching pairs, the clock management synchronization is no longer needed.
As sh_msiof_spi_set_pin_regs() is no longer called at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the MSIOF variant in the R-Car H2 (r8a7790) and M2
(r8a7791) SoCs.
Binding documentation:
- Add future-proof "renesas,msiof-<soctype>" compatible values,
- The default for "renesas,rx-fifo-size" is 256 on R-Car H2 and M2,
- "renesas,tx-fifo-size" and "renesas,rx-fifo-size" are deprecated for
soctype-specific bindings,
- Add example bindings.
Implementation:
- MSIOF on R-Car H2 and M2 requires the transmission of dummy data if
data is being received only (cfr. "Set SICTR.TSCKE to 1" and "Write
dummy transmission data to SITFDR" in paragraph "Transmit and Receive
Procedures" of the Hardware User's Manual).
- As RX depends on TX, MSIOF on R-Car H2 and M2 also lacks the RSCR
register (Receive Clock Select Register), and some bits in the RMDR1
(Receive Mode Register 1) and TMDR2 (Transmit Mode Register 2)
registers.
- Use the recently introduced SPI_MASTER_MUST_TX flag to enable support
for dummy transmission in the SPI core, and to differentiate from other
MSIOF implementations in code paths that need this.
- New DT compatible values ("renesas,msiof-r8a7790" and
"renesas,msiof-r8a7791") are added, as well as new platform device
names ("spi_r8a7790_msiof" and "spi_r8a7791_msiof").
- The default RX FIFO size is 256 words on R-Car H2 and M2.
This is loosely based on a set of patches from Takashi Yoshii
<takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
As different variants of MSIOF have different FIFO sizes, move the default
FIFO sizes to a new struct sh_msiof_chipdata, pointed to from the device
ID data.
[Moved ifdef to fix build -- broonie]
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Documentation:
- Add missing "interrupt-parent", "#address-cells", "#size-cells", and
"clocks" properties,
- Add missing default values for "num-cs", "renesas,tx-fifo-size" and
"renesas,rx-fifo-size",
- Add a reference to the pinctrl documentation.
Implementation:
- As "num-cs" is marked optional, provide a sensible default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Dual/Quad SPI Transfers to the spidev API.
As this uses SPI mode bits that don't fit in a single byte, two new
ioctls (SPI_IOC_RD_MODE32 and SPI_IOC_WR_MODE32) are introduced.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit f477b7fb13 ("spi: DUAL and QUAD
support"), spi_device.mode was enlarged from 8 to 16 bits.
However, the spidev code still only saved 8 bits of data. If a spidev
SPI_IOC_WR_MODE or SPI_IOC_WR_LSB_FIRST request failed, only the lower 8
bits of the SPI mode were restored, inadvertently clearing the upper 8
bits, possibly disabling Quad or Dual SPI transfers for the device.
Save up to 32 bits to fix this.
For SPI_IOC_WR_MODE this is probably not so important, as it doesn't allow
setting Quad or Dual mode anyway, but SPI_IOC_WR_LSB_FIRST is used to just
set or clear a single bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unnecessary space in order to fix the following
checkpatch issues.
WARNING: Unnecessary space after function pointer name
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Mark Brown <broonie@linaro.org>
If during registering SPI master due to SPI device probing a SPI transfer
is issued the DMA buffers are not allocated yet.
This fixes the following oops:
pch_spi 0000:02:0c.1: enabling device (0000 -> 0002)
pch_spi 0000:02:0c.1: master is unqueued, this is deprecated
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c125aa05>] pch_spi_handle_dma+0x15c/0x6f4
[...]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses struct spi_qup_device to store spi->mode and spi->chip_select
settings. We can get these settings in spi_qup_transfer_one and spi_qup_set_cs
without using struct spi_qup_device. Refactor the code a bit to remove
spi_qup_setup(), spi_qup_cleanup(), and struct spi_qup_device.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The module version is unlikely to be updated, use kernel version should be
enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver uses writel_relaxed() which does not exist in x86, ppc, etc.
Make it depend on ARM && COMPILE_TEST to avoid below build error:
CC [M] drivers/spi/spi-qup.o
drivers/spi/spi-qup.c: In function 'spi_qup_set_state':
drivers/spi/spi-qup.c:180:3: error: implicit declaration of function 'writel_relaxed' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [drivers/spi/spi-qup.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
use SET_SYSTEM_SLEEP_PM_OPS to initialize PM entries, this makes the codes
clean and also enable the ability of hibernation support for sirf SPI.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sirf-dma driver enabled generic dt binding for dma channels.
see here we remove self-defined dma channel prop and move to
use generic dma_request_slave_channel.
related changes in dts is something like:
dmas = <&dmac1 9>,
<&dmac1 4>;
dma-names = "rx", "tx";
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix below build error when CONFIG_PM_RUNTIME=y:
C [M] drivers/spi/spi-qup.o
drivers/spi/spi-qup.c: In function 'spi_qup_pm_suspend_runtime':
drivers/spi/spi-qup.c:712:12: error: 'QUP_CLOCK_AUTO_GATE' undeclared (first use in this function)
drivers/spi/spi-qup.c:712:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/spi/spi-qup.c: In function 'spi_qup_pm_resume_runtime':
drivers/spi/spi-qup.c:725:13: error: 'QUP_CLOCK_AUTO_GATE' undeclared (first use in this function)
make[2]: *** [drivers/spi/spi-qup.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes below checkpatch warning:
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(10);
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
fsl_spi_grlib_probe() may update mpc8xxx_spi->max_bits_per_word setting.
So set master->bits_per_word_mask after fsl_spi_grlib_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
spi_bitbang requires custom setup_transfer() to be defined if there is a
custom txrx_bufs(). Thus keep the empty xilinx_spi_setup_transfer() function
in the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz then spi core will handle checking transfer speed.
So we can remove the same checking in this driver.
Also remove checking spi->chip_select in spi_qup_setup(), the checking is done
by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver uses devm_spi_register_master() so don't explicitly call
spi_master_put() in spi_qup_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While normal Dual and Quad SPI Transfers are unidirectional, we must do
a bidirectional transfer if loopback mode is enabled, else rx_buf is not
filled.
With spidev it seemed to work, as spidev uses the same buffer for
tranmission and reception.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If spi_master.cleanup() is not needed, it can be left unimplemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The older Allwinner SoCs (A10, A13, A10s and A20) all have the same SPI
controller.
Unfortunately, this SPI controller, even though quite similar, is significantly
different from the recently supported A31 SPI controller (different registers
offset, split/merged registers, etc.). Supporting both controllers in a single
driver would be unreasonable, hence the addition of a new driver.
Like its more recent counterpart, it supports DMA, but the driver only does PIO
until we have a dmaengine driver for this platform.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI_IMX is selected by imx_v6_v7_defconfig/imx_v4_v5_defconfig and we don't need
to have a default setting which depends on the IMX_HAVE_PLATFORM_SPI_IMX symbol.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current implementation, CS is controlled by GPIO, which is passed
through spi->controller_data. However, the MSIOF HW module has a function
to output CS by itself, which is already enabled and actual switch will be
done by pinmux.
Store the GPIO number in the core cs_gpio field, and ignore it if it is
an invalid (negative) GPIO number.
Loosely based on a patch from Takashi Yoshii <takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both spi_transfer.speed_hz and spi_master.max_speed_hz are u32
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
DT doesn't instantiate SPI children if spi_master.dev.of_node is not set up
properly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI transfer length should be multiple of SPI word size,
where SPI word size should be power-of-two multiple
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to use default implementation of transfer_one_message() which provides
standard handling of delays and chip select management.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Qualcomm Universal Peripheral (QUP) core is an AHB slave that
provides a common data path (an output FIFO and an input FIFO)
for serial peripheral interface (SPI) mini-core. SPI in master
mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Cc: dsneddon@codeaurora.org
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
bus_num might be asigned dynamically to e.g. 32766. In this case the
calculated DMA channel based on SPI bus number is bogus. Use SPI channel
number instead for calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For DT case, spi core will call of_alias_get_id() and set master->bus_num if it
was not set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The purpose of commit 1e8a52e18c
"spi: By default setup spi_masters with 1 chipselect and dynamics bus number"
is to avoid setting default value for bus_num and num_chipselect in spi master
drivers. So let's remove the duplicate code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: David Daney <david.daney@cavium.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove some coding sytle not in standard in former code.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Freescale DSPI module will have two endianess in different platform,
but ARM is little endian. So when DSPI in big endian, core in little endian,
readl and writel can not adjust R/W register in this condition.
This patch will remove general readl/writel, and import regmap mechanism.
Data endian will be transfered in regmap APIs.
Documents: dspi add bool "big-endian" in dts node if DSPI module
work in big endian.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code in sun6i_spi_set_cs() actually clears CPHA and CPOL bits which is
obvious wrong. The define for SUN6I_TFR_CTL_CS_MASK is wrong. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set "master->max_speed_hz = PCH_MAX_BAUDRATE" then we can remove pch_spi_setup.
In additional, pspi->max_speed_hz will never be 0 because it's default value
will be set to master->max_speed_hz.
Also remove list_empty checking in pch_spi_transfer() because the checking is
done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
This checking is already done in the implementation of spi_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While backporting 33cf00e5 ("spi: attach/detach SPI device to the ACPI
power domain"), I noticed that the code changes were suboptimal:
* Why use &spi->dev when we have dev at hand?
* After fixing the above, spi is used only once, so we don't really
need a local variable for it.
This results in the following clean-up.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In spi_add_device(), we have the code to validate spi->chip_select.
So remove the duplicate code in various drivers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
So it will be checked when spi device is added onto the spi bus.
spi_add_device() calls spi_setup() which then calls spi->master->setup().
No need to check it every time sc18is602_transfer_one() is called.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_slink_setup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove tegra_sflash_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_spi_setup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. Then we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
In __spi_validate(), xfer->speed_hz is set to be spi->max_speed_hz if it is not
set for this transfer. However, if spi->max_speed_hz is also not set,
xfer->speed_hz is 0. Some drivers (e.g. au1550, tegra114, tegra20-sflash,
tegra20-slink, etc.) then use below code to avoid setting xfer->speed_hz to 0.
/* Set speed to the spi max fequency if spi device has not set */
spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency;
Let's handle it in spi core.
If spi->max_speed_hz is not set, make it default to spi->master->max_speed_hz.
So In __spi_validate() if both xfer->speed_hz and spi->max_speed_hz are not set,
xfer->speed_hz will be set to spi->master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 0079aae0f1 ("spi: omap2: Add build dependencies for
writel_relaxed()") added an optional Kconfig dependency on SH. That
Kconfig symbol doesn't exist. Apparently SUPERH was intended. Use that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling init_completion() once is enough.
For the rest of the iterations, call reinit_completion() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unused devdata pointer 'spi100k' in function omap1_spi100k_txrx_pio().
Detected by Coverity: CID 1077869.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove functions that only had an effect when using S3C_DMA and inline
dmaengine_terminate_all() since it's pointless to have a function which
expands to a single function call.
Signed-off-by: Mark Brown <broonie@linaro.org>
All the platforms which use the old S3C_DMA API have now been converted to
dmaengine so we can remove the legacy code from the driver, simplifying
maintenance.
Signed-off-by: Mark Brown <broonie@linaro.org>
When using dmaengine allow the core to do the DMA mapping. We still need
local mapping code for the non-dmaengine case so this doesn't save us
anything for now.
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't modify the list entry while iterating the transfer list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit a2fd4f9fa3 'spi: Support transfer speed checking in the core',
the SPI core validates the desired speed of a given transfer against the
minimum and maximum speeds supported by the controller.
So we can remove the same code in this driver and let spi core handle checking
the desired speed of a given transfer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unused devdata pointer 'orion_spi' in function orion_spi_write_read().
Detected by Coverity: CID 1077860.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's pointless to use of_match_ptr within CONFIG_OF guard.
Use of_match_ptr around davinci_spi_of_match when setting .of_match_table.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_master_get_devdata() never returns NULL when spi_alloc_master() success,
so remove NULL test for dspi.
We have ensured master is not NULL before assigning it to dspi->bitbang.master.
So also remove NULL test for dspi->bitbang.master.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.
It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Otherwise, spi_setup() fails with unsupported mode bits message.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
We cannot unconditionally use dma_map_single() to map data for use with
SPI since transfers may exceed a page and virtual addresses may not be
provided with physically contiguous pages. Further, addresses allocated
using vmalloc() need to be mapped differently to other addresses.
Currently only the MXS driver handles all this, a few drivers do handle
the possibility that buffers may not be physically contiguous which is
the main potential problem but many don't even do that. Factoring this
out into the core will make it easier for drivers to do a good job so if
the driver is using the core DMA code then generate a scatterlist
instead of mapping to a single address so do that.
This code is mainly based on a combination of the existing code in the MXS
and PXA2xx drivers. In future we should be able to extend it to allow the
core to concatenate adjacent transfers if they are compatible, improving
performance.
Currently for simplicity clients are not allowed to use the scatterlist
when they do DMA mapping, in the future the existing single address
mappings will be replaced with use of the scatterlist most likely as
part of pre-verifying transfers.
This change makes it mandatory to use scatterlists when using the core DMA
mapping so update the s3c64xx driver to do this when used with dmaengine.
Doing so makes the code more ugly but it is expected that the old s3c-dma
code can be removed very soon.
Signed-off-by: Mark Brown <broonie@linaro.org>
It is fairly common for SPI devices to require that one or both transfer
directions is always active. Currently drivers open code this in various
ways with varying degrees of efficiency. Start factoring this out by
providing flags SPI_MASTER_MUST_TX and SPI_MASTER_MUST_RX. These will cause
the core to provide buffers for the requested direction if none are
specified in the underlying transfer.
Currently this is fairly inefficient since we actually allocate a data
buffer which may get large, support for mapping transfers using a
scatterlist will allow us to avoid this for DMA based transfers.
Signed-off-by: Mark Brown <broonie@linaro.org>
As of commit 5ce0ba8865 ("spi: rcar: add
Renesas QSPI support on RSPI") the rspi driver handles Renesas QSPI, too,
but this was not reflected in the Kconfig help text.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core is now taking care of putting our pins into default
state at probe. Thus we can remove the redundant call for it in probe.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make use of clk_prepare_enable and clk_disable_unprepare to simplify
code. No functional change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no meaningful code sharing between the PIO and DMA variants
(just the timeout calculation) so in order to make the code easier to
work with split the two cases.
Looking at the code it is not clear how the PIO version works for large
transmits, greater than FIFO size is only handled for RX.
Signed-off-by: Mark Brown <broonie@linaro.org>
The GPIO enable and disable is done in the core so does not need to be
replicated in the driver, delete the unneeded code. enable_cs() was not
referenced at all.
Signed-off-by: Mark Brown <broonie@linaro.org>
When used via spidev with more than one messages to tranfer via
SPI_IOC_MESSAGE the current implementation would return with
-EINVAL, since bits_per_word and speed_hz are set in all
transfer structs. And in the 2nd loop status will stay at
-EINVAL as its not overwritten again via fsl_spi_setup_transfer().
This patch changes this behavious by first checking if one of
the messages uses different settings. If this is the case
the function will return with -EINVAL. If not, the messages
are transferred correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the pointer-integer size mismatch warning below:
drivers/spi/spi-gpio.c: In function ‘spi_gpio_setup’:
drivers/spi/spi-gpio.c:252:8: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
cs = (unsigned int) spi->controller_data;
^
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_wait_for_interrupt() unconditionally enables interrupts, even when the
wait condition is already satisfied. This causes a high interrupt load (2
interrupts/byte for full-duplex Single SPI transfers, 1 interrupt/byte for
RSPI with TX Only mode, or QSPI in unidirectional Dual or Quad Transfer
mode).
Change this to return immediately when the wait condition is satisfied.
This dramatically reduces the interrupt load, especially in high-speed
Quad Transfer mode, and increases transfer speed, as no interrupts need to
be handled when there's space available in the output FIFO, or data
available in the input FIFO.
Benchmark results for QSPI on r8a7791 while reading 1 MiB from 30 MHz SPI
FLASH on the Koelsch development board:
Before:
Single SPI Dual SPI Quad SPI
Interrupts: 2096856 1048592 1048594
Mbps: 0.9 1.6 1.6
After:
Single SPI Dual SPI Quad SPI
Interrupts: 1048569 21295 8
Mbps: 0.7 10.8 12.9
I don't know why Single SPI slowed down a bit.
I've also verified functionality for RSPI-RZ on r7s72100, but don't have
benchmark results as there's no SPI FLASH connected to RSPI on the Genmai
development board. Unlike RSPI and QSPI, RSPI-RZ has separate interrupts
for RX and TX, which shows that Single SPI transfers now generate (mostly)
RX interrupts, as expected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently a divide-by-2^n clock is used, causing a very coarse
clock selection, i.e. a 10MHz device will need to use a 6MHz
clock. The McSPI can also use a divide-by-n clock, this patch
adds support for selecting that when possible.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_transfer->speed_hz and spi_transfer->bits_per_word used to only be set when
not using the default settings but are not set on every transfer, causing
omap2_mcspi_setup_transfer to be called on each transfer. This patch changes
the check to only call omap2_mcspi_setup_transfer if the settings needs to be
changed.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for 1 to 8 BPW to driver and removes
excess BPW validation since this is already checked by SPI core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes an issue that the following build error happens when
the CONFIG_OF is not set:
drivers/spi/spi-rspi.c: In function 'rspi_probe':
drivers/spi/spi-rspi.c:1203:26: error: 'rspi_of_match' undeclared (first use in this function)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The process of DMA mapping buffers for SPI transfers does not vary between
devices so in order to save duplication of code in drivers this can be
factored out into the core, allowing it to be integrated with the work that
is being done on factoring out the common elements from the data path
including more sharing of dmaengine code.
In order to use this masters need to provide a can_dma() operation and while
the hardware is prepared they should ensure that DMA channels are provided
in tx_dma and rx_dma. The core will then ensure that the buffers are mapped
for DMA prior to calling transfer_one_message().
Currently the cleanup on error is not complete, this needs to be improved.
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't wait indefinitely for transfers to complete but time out after 10ms
more than we expect the transfer to take on the wire.
Signed-off-by: Mark Brown <broonie@linaro.org>
For better readability, and then we can remove the comment for last transfer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Trivial cleanup to avoid duplicate code in various bits_per_word cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The checking for spi->mode is done in the implementation of spi_setup().
Calling sc18is602_check_transfer(spi, NULL, 0) is pointless because
the code is equivent to checking if spi->max_speed_hz is 0.
Note, sc18is602_check_transfer actually allows spi->max_speed_hz is 0
if t->speed_hz is set. So return error in sc18is602_setup() when
spi->max_speed_hz is 0 does not make sense.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the driver was converted to clk_prepare() the suspend path didn't
have any changes made so the clock remains prepared throughout the runtime
of the driver. Unprepare it when suspended so that any savings that can be
made as a result are made.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver needs not depend on HAVE_CLK.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the platform_device id to uniquely identify each SPI master instance.
Cc: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Quad and Dual SPI Transfers on the Renesas Quad Serial
Peripheral Interface, as found in R-Car Gen2 SoCs like R-Car H2 (r8a7790)
and R-Car M2 (r8a7791):
- Add unidirectional transfer methods for Quad/Dual SPI Transfers.
- Program the sequencer to handle SPI messages with multiple transfer
modes when Quad or Dual transfers are enabled for an SPI slave.
Up to 4 transfer modes per SPI message are supported by the hardware.
- Advertise the availability of Quad and Dual SPI modes on QSPI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
This reverts commit e120cc0dcf.
It causes a NULL pointer dereference with drivers using the generic
spi_transfer_one_message(), which always calls
spi_finalize_current_message(), which zeroes master->cur_msg.
Drivers implementing transfer_one_message() theirselves must always call
spi_finalize_current_message(), even if the transfer failed:
* @transfer_one_message: the subsystem calls the driver to transfer a single
* message while queuing transfers that arrive in the meantime. When the
* driver is finished with this message, it must call
* spi_finalize_current_message() so the subsystem can issue the next
* transfer
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There's only one RSPI/QSPI clock, so we can use NULL as the clock ID
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Jürg Billeter