This adds support for default application priority.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver is currently looking at shared information for determining whether
DCBx can be supported for a given port.
On 4-port devices, up-to-date management firmware can support DCBx on
each port of a given engine independently - but that would cause bnx2x to
misinterpert the support and assume DCBx is supported on both.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability to perform RSS hashing based on encapsulated
headers for a geneve-encapsulated packet.
This also changes the Vxlan implementation in bnx2x to be uniform
for both vxlan and geneve [from configuration perspective].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_schedule_sp_rtnl is exported by bnx2x, although no other module
uses it.
Reported-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default tx ring size of 512 causes an extra page to be
allocated for the tx ring with only 1 entry in it. Reduce it to
511. The default rx ring size is also reduced to 511 to use less
memory by default.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx push is supported for small packets to reduce DMA latency. The
following bugs are fixed in this patch:
1. Fix the definition of the push BD which is different from the DMA BD.
2. The push buffer has to be zero padded to the next 64-bit word boundary
or tx checksum won't be correct.
3. Increase the tx push packet threshold to 164 bytes (192 bytes with the BD)
so that small tunneled packets are within the threshold.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
20G is not supported by production hardware and only the 40GbaseCR4 standard
is supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg
on and off. Autoneg flow control is possible only if autoneg is enabled.
In bnxt_get_settings(), Pause and Asym_Pause are always supported.
Only the advertisement bits change depending on the ethtool -A setting
in auto mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Determine autoneg on|off setting from link_info->autoneg. Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.
2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.
3. To enable autoneg flow control, speed autoneg must be enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.
tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.
This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.
v2: Corrected patch description to avoid confusion.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chipsets with BCM4707 / BCM53018 ID require special handling at a few
places in the code. It's likely there will be more IDs to check in the
future. To simplify it add this trivial helper.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_set_eeprom() function correctly initializes the 'start' variable,
but gcc generates a false warning:
drivers/net/ethernet/broadcom/tg3.c: In function 'tg3_set_eeprom':
drivers/net/ethernet/broadcom/tg3.c:12057:4: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
I have not come up with a way to restructure the code in a way that
avoids the warning without making it less readable, so this adds an
initialization for the declaration to shut up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac driver depends on BCMA_HOST_SOC, which is only used
when CONFIG_BCMA is enabled. However, it is a bool option and can
be set when CONFIG_BCMA=m, and then bgmac can be built-in, leading
to an obvious link error:
drivers/built-in.o: In function `bgmac_init':
:(.init.text+0x7f2c): undefined reference to `__bcma_driver_register'
drivers/built-in.o: In function `bgmac_exit':
:(.exit.text+0x110a): undefined reference to `bcma_driver_unregister'
To avoid this case, we need to depend on both BCMA and BCMA_SOC,
as this patch does. I'm also trying to make the dependency more
readable by splitting it into three lines, and adding a COMPILE_TEST
alternative so we can test-build it in all configurations that
support BCMA.
The added dependency on FIXED_PHY addresses a related issue where
we cannot call fixed_phy_register() when CONFIG_FIXED_PHY=m and
CONFIG_BGMAC=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring index j is not wrapped properly at the end of the ring, causing
it to reference pointers past the end of the ring. For proper loop
termination and to access the ring properly, we need to increment j and
mask it before referencing the ring entry.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware counter is misleading as it counts dropped packets that
don't match the hardware filters for unicast/broadcast/multicast. We
will still report this counter in ethtool -S for diagnostics purposes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use completion ring for ring free response from firmware. The response
will be the last entry in the ring and we can free the ring after getting
the response. This will guarantee no spurious DMA to freed memory.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By the time we execute bcmgenet_mii_probe(), the MDIO bus structure has
long been allocated and registered. Overirring the PHY interrupt using
the MDIO bus structure has no chance to work anymore, because
of_mdiobus_register() has call phy_device_create() for use, which copied
the MDIO bus address's irq for the PHY into the PHY device "irq" member.
Since we do have a proper reference to a PHY device in
bcmgenet_mii_probe(), just assign the desired IRQ value here.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when build_skb failed, it may occure a NULL pointer.
So add a 'NULL check' for it.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly added code in the bnxt driver uses a couple of variables that
are never initialized when CONFIG_BNXT_SRIOV is not set, and gcc
correctly warns about that:
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/net/ethernet/broadcom/bnxt/bnxt.c:10:
drivers/net/ethernet/broadcom/bnxt/bnxt.c: In function 'bnxt_get_max_rings':
include/linux/kernel.h:794:26: warning: 'cp' may be used uninitialized in this function [-Wmaybe-uninitialized]
include/linux/kernel.h:794:26: warning: 'tx' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/broadcom/bnxt/bnxt.c:5730:11: warning: 'rx' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/broadcom/bnxt/bnxt.c:5736:6: note: 'rx' was declared here
This changes the condition so that we fall back to using the PF
data if VF is not available, and always initialize the variables
to something useful.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6e6c5a57fb ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.")
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use HWRM_FW_RESET command to request a self-reset of the embedded
processor(s) after successfully applying a firmware update. For boot
processor, the self-reset is currently deferred until the next PCIe reset.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For future compatibility, zero pad all messages that the driver sends
to the firmware to 128 bytes. If these messages are extended in the
future with new byte enables, zero padding these messages now will
guarantee future compatibility.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb ("phy: Add API for {un}registering an mdio device to
a bus") introduces an API to access mii_bus structures, but missed to
update the sb1250 driver. This results in the following build error.
drivers/net/ethernet/broadcom/sb1250-mac.c: In function 'sbmac_mii_probe':
drivers/net/ethernet/broadcom/sb1250-mac.c:2360:24: error:
'struct mii_bus' has no member named 'phy_map'
Use phy_find_first() instead of open coding it.
Commit 2220943a21 ("phy: Centralise print about attached phy") introduces
the following build error.
drivers/net/ethernet/broadcom/sb1250-mac.c: In function 'sbmac_mii_probe':
drivers/net/ethernet/broadcom/sb1250-mac.c:2383:20: error: 'phydev' undeclared
Fixes: 7f854420fb ("phy: Add API for {un}registering an mdio device to a bus")
Fixes: 2220943a21 ("phy: Centralise print about attached phy")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can support either all combined or all rx/tx rings. The
default is combined, but the user can now select rx/tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify ring memory allocation and MSIX setup to support shared or
non shared rings and do the proper mapping. Default is still to
use shared rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic to calculate how many shared or non shared rings can be
supported. Default is to use shared rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support dedicated or shared completion rings, the ring
indexing and mapping are re-structured as below:
1. bp->grp_info[] array index is 1:1 with bp->bnapi[] array index and
completion ring index.
2. rx rings 0 to n will be mapped to completion rings 0 to n.
3. If tx and rx rings share completion rings, then tx rings 0 to m will
be mapped to completion rings 0 to m.
4. If tx and rx rings use dedicated completion rings, then tx rings 0 to
m will be mapped to completion rings n + 1 to n + m.
5. Each tx or rx ring will use the corresponding completion ring index
for doorbell mapping and MSIX mapping.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each bnxt_napi structure may no longer be having both an rx ring and
a tx ring. Check for a valid ring before using it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an rx and a tx ring are always paired with a completion ring.
We want to restructure it so that it is possible to have a dedicated
completion ring for tx or rx only.
The bnxt hardware uses a completion ring for rx and tx events. The driver
has to process the completion ring entries sequentially for the rx and tx
events. Using a dedicated completion ring for rx only or tx only has these
benefits:
1. A burst of rx packets can cause delay in processing tx events if the
completion ring is shared. If tx queue is stopped by BQL, this can cause
delay in re-starting the tx queue.
2. A completion ring is sized according to the rx and tx ring size rounded
up to the nearest power of 2. When the completion ring is shared, it is
sized by adding the rx and tx ring sizes and then rounded to the next power
of 2, often with a lot of wasted space.
3. Using dedicated completion ring, we can adjust the tx and rx coalescing
parameters independently for rx and tx.
The first step is to separate the rx and tx ring structures from the
bnxt_napi struct.
In this patch, an rx ring and a tx ring will point to the same bnxt_napi
struct to share the same completion ring. No change in ring assignment
and mapping yet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding 3 separate functions to dump the different ring states.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the PCI IDs for the BCM57301 and BCM57402 controllers.
Signed-off-by: David Christensen <davidch@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be forward compatible with future changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware will return the ring group resource when we call
hwrm_func_qcaps(). To be compatible with older firmware, use the
number of tx rings as the number of ring groups if the older firmware
returns 0. When determining how many rx rings we can support, take
the ring group resource in account as well in _bnxt_get_max_rings().
Divide and assign the ring groups to VFs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to keep track of all resources, such as rx rings, tx rings,
cmpl rings, rss contexts, stats contexts, vnics, after we have
divided them for the VFs. Otherwise, subsequent ring changes on
the PF may not work correctly.
We adjust all max resources in struct bnxt_pf_info after they have been
assigned to the VFs. There is no need to keep the separate
max_pf_tx_rings and max_pf_rx_rings.
When SR-IOV is disabled, we call bnxt_hwrm_func_qcaps() to restore the
max resources for the PF.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use local variable pf for repeated access to this pointer.
2. The 2nd argument num_vfs was unnecessarily declared as pointer to int.
This function doesn't change num_vfs so change the argument to int.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware resources required to enable NTUPLE varies depending on
how many rx channels are configured. We need to make sure we have the
resources before we enable NTUPLE. Add bnxt_rfs_capable() to do the
checking.
In addition, we need to do the same checking in ndo_fix_features(). As
the rx channels are changed using ethtool -L, we call
netdev_update_features() to make the necessary adjustment for NTUPLE.
Calling netdev_update_features() in netif_running() state but before
calling bnxt_open_nic() would be a problem. To make this work,
bnxt_set_features() has to be modified to test for BNXT_STATE_OPEN for
the true hardware state instead of checking netif_running().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hardware completes single segment rx frames, don't bother setting
up all the GRO related fields. Pass the SKB up as a normal frame.
Reviewed-by: vasundhara volam <vvolam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, no need to check for bp->rx_nr_rings as it is always >= 1. If the
allocation fails, it is not a fatal error and we can still proceed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_l4_csum_error is now incremented only when offload is enabled
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NC-SI firmware of type apeFW (10) is now supported.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unnecessary "if" statement before the "for" statement:
if (x) {
for (i = 0; i < x; i++)
...
}
Also, change the ring free function to return void as it only returns 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During remove_one, the driver should issue hwrm_func_drv_unrgtr
command to inform firmware that this function has been unloaded.
This is to let firmware keep track of driver present/absent state
when driver is gracefully unloaded. A keep alive timer is needed
later to keep track of driver state during abnormal shutdown.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW has a rare corner case in which a fragmented packet using lots
of frags would not be linearized, causing the FW to assert while trying
to transmit the packet.
To prevent this, we need to make sure the window of fragements containing
MSS worth of data contains 1 BD less than for regular packets due to
the additional parsing BD.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic calls bnxt_close_nic() and bnxt_open_nic() under rtnl_lock
from bnxt_sp_task. BNXT_STATE_IN_SP_TASK must be cleared before calling
bnxt_close_nic() to avoid deadlock.
v2: Fixed white space error. Thanks Dave.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing driver reset from tx_timeout in the next patch,
bnxt_close_nic() will be called from the sp_task workqueue. Calling
cancel_work() on sp_task will hang the workqueue.
Instead, set a new bit BNXT_STATE_IN_SP_TASK when bnxt_sp_task() is running.
bnxt_close_nic() will wait for BNXT_STATE_IN_SP_TASK to clear before
proceeding.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows multiple independent bits to be set for various states.
Subsequent patches to implement tx timeout reset will require this.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The declaration of the bitmap vf_req_snif_bmap using fixed array of
unsigned long will only work on 64-bit archs. Use DECLARE_BITMAP instead
which will work on all archs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.
A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.
Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'flags' field in bnx2x_stats_arr[] serves only one purpose - to tell
us if the statistic is a per-port stat and thus should not be shown for
virtual functions. It's strange that the field can have three different
values. A boolean will do just fine.
Also remove IS_FUNC_STAT(). It was used only once and it's in fact just
a negation of IS_PORT_STAT().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's supposed to be impossible for TPA to give us anything else
than IPv4 or IPv6 here. But in case there is a way to reach this error
by some strange received frames, we don't want to flood the kernel log.
WARN_ONCE is better for this purpose.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_pages() already prints a warning when it fails. No need to emit
another message. Certainly not at KERN_ERR level, because it is no big
deal if this GFP_ATOMIC allocation fails occasionally.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46e8a249423ff "bnx2x: Add FW 7.13.1.0" added said .bin FW to
linux-firmware; This patch incorporates the FW in the bnx2x driver.
This introduces 2 fixes/enhancements:
- In some management protocols there are outer-vlan configurations
that can be dynamically changed while device is running. This fixes
some corner cases where such a change did not take effect.
- Prevent VFs from sending MAC control frames; FW would treat a VF
sending such a packet as malicious and block any further communication
done by the VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, port statistics are being presented when using `ethool -S' only
for single-function devices, but there are some port statistics which are
crucial for analyzing bottle-necks. E.g., HW Rx discards due to lack of
buffer space [when device isn't handling ingress traffic fast enough].
Judging the pros and cons, it was decided that in-order to better support
automatic dump-gathering tools, bnx2x should no longer hide those stats.
This leaves only VFs lacking the port statistics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver already has an internal counter for number of times a given queue
had to be stopped due to Tx ring exhaustion.
This add the counter to the statistics presented by driver, e.g., by using
`ethtool -S'.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commmit ac7eccd4d4 "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.
2) Several spots need to get to the original listner for SYN-ACK
packets, most spots got this ok but some were not. Whilst covering
the remaining cases, create a helper to do this. From Eric Dumazet.
3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
from Rasmus Villemoes.
4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.
5) Use after free in mvneta driver, from Justin Maggard.
6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.
7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd
Bergmann.
8) Fix multicast getsockopt deadlock, from WANG Cong.
9) Fix deadlock in btusb, from Kuba Pawlak.
10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
counter state. From Sabrina Dubroca.
11) Fix packet_bind() race, which can cause lost notifications, from
Francesco Ruggeri.
12) Fix MAC restoration in qlcnic driver during bonding mode changes,
from Jarod Wilson.
13) Revert bridging forward delay change which broke libvirt and other
userspace things, from Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
Revert "bridge: Allow forward delay to be cfgd when STP enabled"
bpf_trace: Make dependent on PERF_EVENTS
qed: select ZLIB_INFLATE
net: fix a race in dst_release()
net: mvneta: Fix memory use after free.
net: Documentation: Fix default value tcp_limit_output_bytes
macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
mvneta: add FIXED_PHY dependency
net: caif: check return value of alloc_netdev
net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
drivers: net: xgene: fix RGMII 10/100Mb mode
netfilter: nft_meta: use skb_to_full_sk() helper
net_sched: em_meta: use skb_to_full_sk() helper
sched: cls_flow: use skb_to_full_sk() helper
netfilter: xt_owner: use skb_to_full_sk() helper
smack: use skb_to_full_sk() helper
net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
bpf: doc: correct arch list for supported eBPF JIT
dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
bonding: fix panic on non-ARPHRD_ETHER enslave failure
...
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of always calling pci_sriov_disable() in remove_one(),
the driver should detect whether VFs are currently assigned
to the VMs. If the VFs are active in VMs, then it should not
disable SRIOV as it is catastrophic to the VMs. Instead,
it just leaves the VFs alone and continues to unload the PF.
The user can then cleanup the VMs even after the PF driver
has been unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign the return value from bitmap_find_free_region() to an integer
variable and check for negative error codes first, before assigning
the bit ID to the unsigned sw_id field.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use offset 0x4014 for reading CAG interrupt status,
the actual CAG register must be mapped to GRC bar0 window #4.
Otherwise, the driver is reading garbage. This patch corrects
this issue.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The profile ID in the completion record needs to be ANDed with the
profile ID mask of 0x1f. This bug was causing the SKB hash type
and the gso_type to be wrong in some cases.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the sp event bits to be bit positions instead of bit values since
the bit helper functions are expecting the former.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN may be a loadable module, and this driver cannot be built-in
in that case, or we get a link error:
drivers/built-in.o: In function `__bnxt_open_nic':
drivers/net/ethernet/broadcom/bnxt/bnxt.c:4581: undefined reference to `vxlan_get_rx_port'
This adds a Kconfig dependency that ensures that either VXLAN is
disabled (which the driver handles correctly), or we depend on
VXLAN itself and disallow built-in compilation when VXLAN is
a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY on GENET v1->v3 is extremely finicky, and will show occasional
failures based on the timing and reset sequence, ranging from duplicate
packets, to extremely high latencies.
Perform an additional software reset, and re-configuration to make sure it is
in a consistent and working state.
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com>
Tested-by: Jim Hull <jim.hull@hpe.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom ethernet driver for the new family of NetXtreme-C/E
ethernet devices.
v5:
- Removed empty blank lines at end of files (noted by David Miller).
- Moved busy poll helper functions to bnxt.h to at least make the
.c file look less cluttered with #ifdef (noted by Stephen Hemminger).
v4:
- Broke up 2 long message strings with "\n" (suggested by John Linville)
- Constify an array of strings (suggested by Stephen Hemminger)
- Improve bnxt_vf_pciid() (suggested by Stephen Hemminger)
- Use PCI_VDEVICE() to populate pci_device_id table for more compact
source.
v3:
- Fixed 2 more sparse warnings.
- Removed some unused structures in .h files.
v2:
- Fixed all kbuild test robot reported warnings.
- Fixed many of the checkpatch.pl errors and warnings.
- Fixed the Kconfig description (noted by Dmitry Kravkov).
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.
This results in a forced speed of 1000 and RX/TX failure.
Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dc ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnx2_init_board, missing free temp_stats_blk on error path when
some operations do failed. Just add the 'kfree' operation.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we have two processes to do:
P1#: ifconfig eth0 down; which will call bnx2_close, then will
, and set Null to stats_blk
P2#: ifconfig eth0; which will call bnx2_get_stats64, it will
use stats_blk.
In one case:
--P1#-- --P2#--
stats_blk(no null)
bnx2_free_mem
->bp->stats_blk = NULL
GET_64BIT_NET_STATS
then it will cause 'NULL Pointer' Problem.
it is as well with 'ethtool -S ethx'.
Allocate the statistics block at probe time so that this problem is
impossible
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
After a good amount of debugging, I found bnx2x was byte swaping
the 40 bytes of rss_key.
If we byte swap the key, then bnx2x generates hashes matching
MSDN specs as documented in (Verifying the RSS Hash Calculation)
https://msdn.microsoft.com/en-us/library/windows/hardware/ff571021%
28v=vs.85%29.aspx
It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking twice for ec->tx_coalesce_usecs_high, remove the
duplicate test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild-all@01.org
Fixes: 2f9130709d ("net: bcmgenet: Implement TX coalescing control knobs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.
We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.
We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.
Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.
While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c48f350ff5 "bnx2x: Add MFW dump support" added the
bnx2x_update_mfw_dump() function that reads the current time and stores
it in a 32-bit field that gets passed into a buffer in a fixed format.
This is potentially broken when the epoch overflows in 2038, and
otherwise overflows in 2106. As we're trying to avoid uses of
struct timeval for this reason, I noticed the addition of this
function, and tried to rewrite it in a way that is more explicit
about the overflow and that will keep working once we deprecate
struct timeval.
I assume that it is not possible to change the ABI any more, otherwise
we should try to use a 64-bit field for the seconds right away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5597008db ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:
drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'
Add the missing argument.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.
Fixes: aed93e0bf4 ("tg3: Add hwmon support for temperature")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: stable@vger.kernel.org [v3.6+]
Signed-off-by: David S. Miller <davem@davemloft.net>
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for 3 new PCI device combinations -
1077:16a1, 1077:16a4 and 1077:16ad.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom buses may have more than 1 Ethernet device. This is used e.g.
to have few interfaces connected to different switch ports. So far we
saw chipsets with only 2 devices (e.g. BCM4706) but recent ones have
up to 3 (e.g. Netgear R8000 uses 3rd interface for most of switch
traffic, lower interfaces are for some kind of offloading).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the dma flags of multiq ring buffer int the interface stop
process. This patch fixes that the genet is not running while the
interface is re-enabled.
$ ifup eth0 - running after booting
$ ifdown eth0
$ ifup eth0 - not running and occur tx_timeout
The bcmgenet_dma_disable() in bcmgenet_open() do clean ring16 dma flag
only. If the genet has multiq, the dma register is not cleaned. and
bcmgenet_init_dma() is not done correctly. in case
GENET_V2(tx_queues=4), tdma_ctrl has 0x1e after running
bcmgenet_dma_disable().
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_timeout() executes in atomic context, yet we will invoke
napi_disable() which does sleep. Looking back at the changes, disabling
TX napi and re-enabling it is completely useless, since we reclaim all
TX buffers and re-enable interrupts, and wake up the TX queues.
Fixes: 13ea657806 ("net: bcmgenet: improve TX timeout")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34fa14cc0 ("bnx2x: Add vxlan RSS support") has introduced an
endianity issue when passing the vxlan UDP port to the HW.
Reported-by: <fengguang.wu@intel.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest FW submission added some vxlan offload capabilities to our device.
This patch adds the ability to connect to the vxlan NDOs and configure
the UDP port associated with it in the HW.
The device would now be capable of performing RSS according to the
inner headers of the vxlan packets.
Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware tells driver in case bandwidth configuration for
a specific function exists, but [regretably] the same field has different
meanings depending on the multi-function mode - it can either be
a percentile value or an actual speed.
For newer multi-function modes current logic is incorrect -
driver understands values as actual speeds instead of percentages,
causing the resulting chip configuration to be incorrect.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.
Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.
This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error flows its possible to free an SKB even if it was not allocated.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 230d00eb4b ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has introduced
an incorrect logic for checking whether pvid should be configured for
a vf, causing the hypervisor driver to send unneeded ramrods for all of
the vfs each time a pvid has changed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes the RX
interrupt handler to poll for incoming packets, and cleans up all TX
queues by invoking the TX interrupt handler.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes both of our
interrupt handlers for the different RX/TX queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has broken
compilation when CONFIG_BNX2X_SRIOV is not set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver always uses vlan-promisc mode, i.e., it receives both
tagged and untagged traffic and lets the network stack drop packets
tagged with unrequested vlan tags.
This patch implements vlan-filtering offload in the driver -
Unless explicitly configured to promisc mode, only untagged packets or
packets tagged with requested vlans would reach the Rx flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change
detection") added a fixed PHY link_update callback for MoCA PHYs when
registered using platform_data exclusively, this change is also
applicable to systems using Device Tree as their primary configuration
interface.
In order for this to work, move the link_update assignment into
bcmgenet_moca_phy_setup() where we know for sure that we are running on
a MoCA GENET instance, and do not override phydev->link since this is:
- properly taken care of by the PHY library by getting the link UP/DOWN
interrupts
- this now runs everytime we call bcmgenet_open(), so we need to
preserve whatever we detected before we went administratively DOWN and
then UP
- we need to make sure that MoCA PHYs start with a link DOWN during
probe in order to force a link transition to occur
To avoid a forward declaration, move bcmgenet_fixed_phy_link_update()
above its caller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of multiplying the number of checks for IS_ERR(priv->clk),
simply NULLify the 'struct clk' pointer which is something the Linux
common clock framework perfectly deals with and does early return for
each and every single clk_* API functions.
Having every single function check for !IS_ERR(priv->clk) is both
redundant and error prone, as it turns out, we were doing it for the
main GENET clock: priv->clk, but not for the Wake-on-LAN or EEE clock,
so let's just be consistent here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices with up-to-date management FW will be able to store register dumps
on their persistent storage - in case management FW identifies a fatal
error it would gather and store such dumps, which could later be retrieved
using specific debug tools.
This patch adds the necessary part in the driver in order to make the
feature operational, as well as update users [under debug] during load
in case their device contains a dump of a previous crash.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new multi-function mode, enabling driver to
initialize such devices and correctly interacting with management FW
for fully utilizing their features.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new copper phy.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.
This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves bnx2x into using 7.12.30 FW. Said firmware fixes the following:
- Packets from a VF with pvid configured which were sent with a
different vlan were transmitted instead of being discarded.
- FCoE traffic might not recover after a failue while there's traffic
to another function.
In addition, this FW opens the door for the driver to implement several
new features; Specifically, this enhances the device's support for
encapsulated packets and will allow vxlan/geneve offloads to be added in
the future, as well as vlan filtering offload.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-07-17
This series contains updates to igb, ixgbe, ixgbevf, i40e, bnx2x,
freescale, siena and dp83640.
Jacob provides several patches to clarify the intended way to implement
both SIOCSHWTSTAMP and ethtool's get_ts_info(). It is okay to support
the specific filters in SIOCSHWTSTAMP by upscaling them to the generic
filters.
Alex Duyck provides a igb patch to pull the time stamp from the fragment
before it gets added to the skb, to avoid a possible issue in which the
fragment can possibly be less than IGB_RX_HDR_LEN due to the time stamp
being pulled after the copybreak check. Also provides a ixgbevf patch to
fold the ixgbevf_pull_tail() call into ixgbevf_add_rx_frag(), which gives
the advantage that the fragment does not have to be modified after it is
added to the skb.
Fan provides patches for ixgbe/ixgbevf to set the receive hash type
based on receive descriptor RSS type.
Todd provides a fix for igb where on check for link on any media other
than copper was not being detected since it was looking on the incorrect
PHY page (due to the page being used gets switched before the function
to check link gets executed).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have reworked the way we perform the PHY initialization, we
no longer need to differentiate between init time vs. non-init time
calls, just use a dev_info_once() print to print the PHY type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently doing a full PHY initialization and even starting the
pHY state machine during bcmgenet_mii_init() which is executed in the
driver's probe function. This is convenient to determine whether we can
attach to a proper PHY device but comes at the expense of spending up to
10ms per MDIO transactions (to reach the waitqueue timeout), which slows
things down.
This also creates a sitaution where we end-up attaching twice to the
PHY, which is not quite correct either.
Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update
its error path accordingly.
Avoid printing the message "attached PHY at address 1 [...]" every time
we bring up/down the interface and remove this print since it duplicates
what the PHY driver already does for us.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our internal GPHY might be powered off before we attempt scanning the
MDIO bus and bind a driver to it. The way we are currently determining
whether a PHY is internal or not is done *after* we have successfully
matched its driver. If the PHY is powered down, it will not respond to
the MDIO bus, so we will not be able to bind a driver to it.
Our Device Tree for GENET interfaces specifies a "phy-mode" value:
"internal" which tells if this internal uses an internal PHY or not.
If of_get_phy_mode() fails to parse the 'phy-mode' property, do an
additional manual lookup, and if we find "internal" set the
corresponding internal variable accordingly.
Replace all uses of phy_is_internal() with a check against
priv->internal_phy to avoid having to rely on whether or not
priv->phydev is set correctly.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently disabling the GPHY interface during bcmgenet_close(),
and attempting to power it back on during bcmgenet_open(). This works
fine for the first time, because we called bcmgenet_mii_config() which
took care of enabling the interface, however, bcmgenet_power_up() really
needs to power on the GPHY for correctness.
This will be particularly important as we want to move
bcmgenet_mii_probe() down to bcmgenet_open() to avoid seeing the "PHY
already attached" message.
Fixes: a642c4f790 ("net: bcmgenet: power up and down integrated GPHY when unused")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_open()'s error path call free_irq() with a dev_id argument
different from the one we used to call request_irq() with, this will
make us trip over the warning in kernel/irq/manage.c:__free_irq()
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently issuing multiple PHY resets during a suspend/resume,
first during bcmgenet_power_up() which does a hardware reset, then a
software reset by calling bcmgenet_mii_reset(). This is both unnecessary
and can take as long as 10ms per MDIO transactions while we re-apply
workarounds because we do not yet have MDIO interrupts enabled.
phy_resume() takes care of re-apply our workarounds in case we need any,
and bcmgenet_power_up() does a PHY hardware reset, all of this is more
than enough to guarantee that the PHY operates correctly.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
Pass 1 parts had a number of significant erratas and were only available
in small numbers and under NDA. Full support also required the use of a
special toolchain that kept branches properly aligned. These workarounds
were never upstreamed and the only toolchain known to have them is
Montavista's GCC 3.0-based toolchain which completly obsoleted if not
useless these days.
So now that automated testing has tripped over the user of the
-msb1-pass1-workarounds option, rather than fixing it remove support for
pass 1 parts.
Probably nobody will notice. I seem to own the last know pass 1 board
and I haven't noticed another one in the wild in the past decade, at
least.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
bcmgenet driver needs to separate packet drops from packet errors.
When the driver has to drop a *good* packet, due to lack of buffers or
replacement skbs, increment only dev->stats.[rx|tx]_dropped.
When the driver encounters a bad Rx packet or Tx error, increment only
dev->stats.[rx|tx]_errors + relevant detailed error counter.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr().
Here, this change is setting addr_assign_type to NET_ADDR_RANDOM.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@
identifier a,b;
@@
-random_ether_addr(a->b);
+eth_hw_addr_random(a);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.
Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().
Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DMA_API_DEBUG=y bnx2x triggers the error "DMA-API: device
driver frees DMA memory with wrong function".
On archs where PAGE_SIZE > SGE_PAGE_SIZE it also triggers "DMA-API:
device driver frees DMA memory with different size".
Fix this by making the mapping and unmapping symmetric:
- Do not map the whole pool page at once. Instead map the
SGE_PAGE_SIZE-sized pieces individually, so they can be unmapped in
the same manner.
- What's mapped using dma_map_page() must be unmapped using
dma_unmap_page().
Tested on ppc64.
Fixes: 4cace675d6 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to FW constraints, driver must make sure that transmitted SKBs will
not be too fragmented, or in the case that they are - that each 'window'
of fragments passed to the FW would contain at least an mss worth of data.
For encapsultaed packets the calculation is wrong, since it ignores the
inner headers in the calculation of the headers' length.
This could lead to a FW assertion in case of a too-fragmented encapsulated
packet.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During an error flow when trying to access the nvram the driver doesn't
release the hw lock it acquired.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver statistics flow access MACs and those might reset during
link re-configurations, when we're about to change link properties we
have to make sure that statistics are not operational.
Statisics would be re-enabled [i.e., gathering of statistics would
re-commence] once physical link is achieved again.
Since driver employs a link-flap avoidance scheme, there are scenarios
where driver will receive no indication that the new link is up, and
as a result the statistics would not be re-enabled.
Preventing LFA from working in such cases would guarantee that we'll
always receive such indications and thus will fix statistics gathering.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
20g-capable devices are not configured properly for self-test, using
10g as their speed which cause the link indication to remain down and
fail the internal loopback test.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in today's driver where VF requests to add/remove MAC filters
always reach the Hypervisor as add requests.
This prevents the VF from changing its MAC address, as it cannot remove the
previously configured MAC and runs out of MAC credits.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.
Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.
This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each time a flow finishes reads from the classification shadow
configuration in the driver, that flow would check for pending commands
and pass them to FW if possible.
In case there's already a completion pending command, I.e., a ramrod
that has been sent to the FW and is yet to be completed while said flow
tries to configure the pending command we would get a false error message
in logs [and panic if SOE was used for driver compilation] since the
command could not have been completed.
This prevents said print [and panic]; The pending command will be sent by
the time the completion of the current sent command would arrive.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool shows KR supported/advertised speeds incorrectly as baseT
in cases the board is in fact KR-base.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes several issues relating to asymmetric configuration:
1. When user requests to disable TX, the local-device needs to
advertise both PAUSE and ASM_DIR, but to avoid transmitting pause
frames. In the 578xx, it would ignore the TX disable.
2. When user advertises RX-only, ASM_DIR was advertised instead of
PAUSE/ASM_DIR.
3. When changing mode, the advertised PAUSE/ASM_DIR was not cleared
before setting new one, so disabling RX or TX had no impact on the
'advertised' as appeared in the 'ethtool -a' output.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHYs/switches such as Broadcom's BCM53125 have a hardware
bug which makes them not release the MDIO line during turn-around time.
This gets flagged by the GENET MDIO controller as a read failure, and we
fail the read transaction.
Check the MDIO bus phy_ignore_ta_mask bitmask for the PHY we are reading
from and if it is listed in this bitmask, ignore the read failure and
proceed with returning the data we read out of the controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What BGMAC defines as BGMAC_PHY_NOREGS is in fact the Broadcom Ethernet
switches' pseudo-PHY address (30), utilize the newly introduced constant
from brcmphy.h
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What B44 has been locally using as B44_PHY_ADDR_NO_LOCAL_PHY is in fact
the Broadcom Ethernet switches pseudo-PHY address (30). Update the
header to use the newly introduced constant and update comments so they
are within 80 columns and consistent.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII block is currently only powered on when using RGMII or
RGMII_NO_ID, which is not correct when using the GENET interface in MII
or Reverse MII modes. We always need to power on the RGMII interface for
this block to properly work, regardless of the MII mode in which we
operate.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver gets unregistered a call to netif_napi_del() was
missing, this all was also missing in the error paths of
b44_init_one().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump useful ring statistics along with interrupt status, software
maintained pointers and hardware registers to help troubleshoot TX queue
stalls.
When a timeout occurs, disable TX NAPI for the rings, dump their states
while interrupts are disabled, re-enable interrupts, NAPI and queue flow
control to help with the recovery.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver allocates one page for each buffer on the rx ring, which is
too much on architectures like ppc64 and can cause unexpected allocation
failures when the system is under stress. Now, we keep a memory pool
per queue, and if the architecture's PAGE_SIZE is greater than 4k, we
fragment pages and assign each 4k segment to a ring element, which
reduces the overall memory consumption on such architectures. This
helps avoiding errors like the example below:
[bnx2x_alloc_rx_sge:435(eth1)]Can't alloc sge
[c00000037ffeb900] [d000000075eddeb4] .bnx2x_alloc_rx_sge+0x44/0x200 [bnx2x]
[c00000037ffeb9b0] [d000000075ee0b34] .bnx2x_fill_frag_skb+0x1ac/0x460 [bnx2x]
[c00000037ffebac0] [d000000075ee11f0] .bnx2x_tpa_stop+0x160/0x2e8 [bnx2x]
[c00000037ffebb90] [d000000075ee1560] .bnx2x_rx_int+0x1e8/0xc30 [bnx2x]
[c00000037ffebcd0] [d000000075ee2084] .bnx2x_poll+0xdc/0x3d8 [bnx2x] (unreliable)
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dff173de84 ("bnx2x: Fix statistics locking scheme") changed the
bnx2x locking around statistics state into using a mutex - but the lock
is being accessed via a timer which is forbidden.
[If compiled with CONFIG_DEBUG_MUTEXES, logs show a warning about
accessing the mutex in interrupt context]
This moves the implementation into using a semaphore [with size '1']
instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionnaly we may get oversized packets from the hardware which exceed
the nomimal 2KiB buffer size we allocate SKBs with. Add an early check
which drops the packet to avoid invoking skb_over_panic() and move on to
processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bcm_sysport_desc_rx() calls bcm_sysport_rx_refill() at the end of Rx
packet processing loop, after the current Rx packet has already been passed to
napi_gro_receive(). However, bcm_sysport_rx_refill() might fail to allocate a new
Rx skb, thus leaving a hole on the Rx queue where no valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcm_sysport_rx_refill() to retain the current Rx skb on the
Rx queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcm_sysport_desc_rx() to call bcm_sysport_rx_refill() at the
top of Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
This is loosely inspired from d6707bec59 ("net: bcmgenet: rewrite
bcmgenet_rx_refill()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a 1:1 mapping between the software maintained control block in
priv->rx_cbs and the buffer address in priv->rx_bds, such that there is
no need to keep computing the buffer address when refiling a control
block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the TX path, allow the RX path to be configured with both
'rx-frames' and 'rx-usecs' coalescing parameters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure both 'tx-frames' which controls how many frames
are doing to trigger a single interrupt and 'tx-usecs' which dictates how long
to wait before an interrupt should be services.
Since our timer resolution is close to 8.192 us, we round up to the nearest
value the 'tx-usecs' timeout value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 12a8541d5c "bnx2x: Delay during kdump load" added a 5 seconds
delay to bnx2x's probe function in the kdump case to let the firmware
realize the old driver is gone.
The problem with the delay is that it is per-device, so if you have
several bnx2x NICs in NPAR mode, the delays can accumulate to minutes.
Fix it by adjusting the delay so that we do not wait more than
necessary, i.e. no more delaying after 5 seconds of kernel boot time.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Submit 909d9faae2 ("bnx2x: Prevent inner-reload while VFs exist")
contained a bug - MTU change was not prevented by it; Instead, it
`randomally' prevented bnx2x_resume() from running [harmless yet wrong].
This moves the check to its correct spot.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a kdump environment interfaces might be re-loaded without a proper
unload sequence in the previous running kernel.
bnx2x management FW and driver maintains a `pulse' that notifies the FW
that the driver is still up and running.
Driver load on the kdump kernel should be performed only after the pulse
has been out-of-sync long enough for the management FW to identify that
the driver has crashed, on which point it will perform some necessary
cleanup of the HW.
In today's distros kdump loading is quite fast, sometimes too fast for our
FW to get out-of-sync. This patch delays the bnx2x's probe during kdump
to allow a proper re-load on the kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the 0x0x prefix in an integer constant.
In this case, while at it, also fix a typo (s/unitcast/unicast/).
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are redundant with dev->features. Remove them.
Just make sure to set dev->features ourselves in bnx2x_set_features()
before performing the reload of the card.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is simpler to have the TPA mode as one three-state variable.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If disable_tpa is set, remove NETIF_F_LRO from hw_features, so ethtool sees
it as "off [fixed]".
Note that setting the NETIF_F_LRO bit in dev->features in the 'else'
branch is not needed, because the bit was already set by
bnx2x_init_dev().
Then the check for disable_tpa in in bnx2x_fix_features() becomes unnecessary.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x's 'disable_tpa=1' module option is not respected properly and TPA
(transparent packet aggregation) remains enabled. Even though the
module option causes LRO to be disabled, TPA is enabled in GRO mode.
Additionally, disabling GRO via ethtool then has no effect. One can
still observe tpa_* statistics increase and large packets being received
in tcpdump.
The bug was an unintended consequence of commit aebf6244cd "bnx2x: Be
more forgiving toward SW GRO".
Fix it by following the bp->disable_tpa flag when initializing fp's.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When having permanent EEH error, the PCI device will be removed
from the system. For this case, we shouldn't set pcierr_recovery
to true wrongly, which blocks the driver to release the allocated
interrupts and their handlers. Eventually, we can't disable MSI
or MSIx successfully because of the MSI or MSIx interrupts still
have associated interrupt actions, which is turned into following
stack dump.
Oops: Exception in kernel mode, sig: 5 [#1]
:
[c0000000003b76a8] .free_msi_irqs+0x80/0x1a0 (unreliable)
[c00000000039f388] .pci_remove_bus_device+0x98/0x110
[c0000000000790f4] .pcibios_remove_pci_devices+0x9c/0x128
[c000000000077b98] .handle_eeh_events+0x2d8/0x4b0
[c0000000000782d0] .eeh_event_handler+0x130/0x1c0
[c000000000022bd4] .kernel_thread+0x54/0x70
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After d75b1ade56 ("net: less interrupt masking in NAPI") polling
function has to return whole budget when it wants NAPI to call it again.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Fixes: eb64e2923a ("bgmac: leave interrupts disabled as long as there is work to do")
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some feature changes, driver employes an inner-reload flow where it
resets the function and re-configures it with the new required set of
parameters.
Such a flow proves fatal to any VF since those were not intended to be used
while HW is being reset underneath, causing them [at best] to lose all
connectivity.
This changes driver behavior to fail all configuration changes [e.g., mtu
change] requested of the driver in case VFs are active.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix verifier memory corruption and other bugs in BPF layer, from
Alexei Starovoitov.
2) Add a conservative fix for doing BPF properly in the BPF classifier
of the packet scheduler on ingress. Also from Alexei.
3) The SKB scrubber should not clear out the packet MARK and security
label, from Herbert Xu.
4) Fix oops on rmmod in stmmac driver, from Bryan O'Donoghue.
5) Pause handling is not correct in the stmmac driver because it
doesn't take into consideration the RX and TX fifo sizes. From
Vince Bridgers.
6) Failure path missing unlock in FOU driver, from Wang Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: dsa: use DEVICE_ATTR_RW to declare temp1_max
netns: remove BUG_ONs from net_generic()
IB/ipoib: Fix ndo_get_iflink
sfc: Fix memcpy() with const destination compiler warning.
altera tse: Fix network-delays and -retransmissions after high throughput.
net: remove unused 'dev' argument from netif_needs_gso()
act_mirred: Fix bogus header when redirecting from VLAN
inet_diag: fix access to tcp cc information
tcp: tcp_get_info() should fetch socket fields once
net: dsa: mv88e6xxx: Add missing initialization in mv88e6xxx_set_port_state()
skbuff: Do not scrub skb mark within the same name space
Revert "net: Reset secmark when scrubbing packet"
bpf: fix two bugs in verification logic when accessing 'ctx' pointer
bpf: fix bpf helpers to use skb->mac_header relative offsets
stmmac: Configure Flow Control to work correctly based on rxfifo size
stmmac: Enable unicast pause frame detect in GMAC Register 6
stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree
stmmac: Add defines and documentation for enabling flow control
stmmac: Add properties for transmit and receive fifo sizes
stmmac: fix oops on rmmod after assigning ip addr
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
Commit 9a2620c877 ("bnx2x: prevent WARN during driver unload")
switched the napi/busy_lock locking mechanism from spin_lock() into
spin_lock_bh(), breaking inter-operability with netconsole, as netpoll
disables interrupts prior to calling our napi mechanism.
This switches the driver into using atomic assignments instead of the
spinlock mechanisms previously employed.
Based on initial patch from Yuval Mintz & Ariel Elior
I basically added softirq starvation avoidance, and mixture
of atomic operations, plain writes and barriers.
Note this slightly reduces the overhead for this driver when no
busy_poll sockets are in use.
Fixes: 9a2620c877 ("bnx2x: prevent WARN during driver unload")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
The ring size is always known at compile time, so make the code a bit
more efficient
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to inform the hardware about the first invalid (not yet
filled) rx slot, by writing its DMA descriptor pointer offset to the
BGMAC_DMA_RX_INDEX register.
This register was set to a value exceeding the rx ring size, effectively
allowing the hardware constant access to the full ring, regardless of
which slots are initialized.
To fix this issue, always mark the last filled rx slot as invalid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating buffers at device init time and initializing
descriptors at device open, do both at the same time (during open).
Free all buffers when closing the device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limiting it to 511 looks like a failed attempt at leaving one descriptor
empty to allow the hardware to stop processing a buffer that has not
been prepared yet. However, this doesn't work because this affects the
total ring size as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In very rare cases, the MAC can catch an internal buffer that is bigger
than it's supposed to be. Instead of crashing the kernel, simply pass
the buffer back to the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a new buffer before processing the completed one. If allocation
fails, reuse the old buffer.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet buffer offset of 30 bytes is inefficient, because the first 2
bytes end up in a different cacheline.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always poll rx and tx during NAPI poll instead of relying on the status
of the first interrupt. This prevents bgmac_poll from leaving unfinished
work around until the next IRQ.
In my tests this makes bridging/routing throughput under heavy load more
stable and ensures that no new IRQs arrive as long as bgmac_poll uses up
the entire budget.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep incrementing ring->start and ring->end instead of pointing it to
the actual ring slot entry. This simplifies the calculation of the
number of free slots.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.
Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.
The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
register.
5. When the fixed PHY link status register is being read, the new
function bcmgenet_fixed_phy_link_update() gets called. It copies
the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
hardware link state.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two reasons for having this header in the common place:
1) Simplifying drivers that read NVRAM entries. We will be able to
safely call bcm47xx_nvram_* functions without #ifdef-s.
2) Getting NVRAM driver out of MIPS arch code. This is needed to support
BCM5301X arch which also requires this NVRAM driver. Patch for that
will follow once we get is reviewed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: linux-soc@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8619/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On phy_mac_interrupt() call, the new_link parameter should be 0 or 1.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define UMAC_IRQ_LINK_EVENT to simplify link event handling code.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_init_dma() fails, it cleans up after itself. Rx and Tx
DMAs are off, and NAPI instances haven't been netif_napi_add()'ed.
Therefore, we need to skip calling bcmgenet_fini_dma() on the error
handling path. bcmgenet_resume() already does this correctly.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_fini_dma() is the only caller of __bcmgenet_fini_dma().
Move __bcmgenet_fini_dma() code inside bcmgenet_fini_dma().
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define for UMAC_IRQ_RXDMA_DONE and UMAC_IRQ_TXDMA_DONE in order
to simplify the code that handles Rx and Tx default queue interrupts.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bool constants as the return values instead of 1 and 0.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that due to errors [either on PCI or on device itself]
registers reads would fail, returning all-Fs.
This adds a check as early as possible so that driver will not read junk
values and make incorrect probe decisions according to them; instead,
gracefully fail the probe.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of link changes are now being stored in shared memory [by all possible
link owners], for management use [as well as possible debug information for
dumps].
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable controlling Post2, coeff, IPreDriver and IFir according to NVRAM setup.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device appears to use a 64 bit nanoseconds register, and so with
this patch the driver should be ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for multiple Rx queues:
1. Add NAPI context per Rx queue
2. Modify Rx interrupt and Rx NAPI code to handle multiple Rx queues
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new bcmgenet functions to handle the NAPI calls to:
netif_napi_add()
napi_enable()
napi_disable()
netif_napi_del()
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new bcmgenet functions to handle the NAPI calls to:
netif_napi_add()
napi_enable()
napi_disable()
netif_napi_del()
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more meaningful variable names int0_enable and int1_enable when
enabling bcmgenet interrupts.
For Rx default queue interrupts, use:
UMAC_IRQ_RXDMA_BDONE | UMAC_IRQ_RXDMA_PDONE
For Tx default queue interrupts, use:
UMAC_IRQ_TXDMA_BDONE | UMAC_IRQ_TXDMA_PDONE
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the two kcalloc() calls first, before proceeding into Rx/Tx DMA init.
Makes the error case handling much simpler.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary function parameter priv. Use ring->priv instead.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused priv->int0_mask and priv->int1_mask.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the interface is not used, power down the integrated GPHY during
suspend. Similarly to bcmgenet_open(), bcmgenet_resume() powers on the GPHY
prior to any UniMAC activity.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the GPHY power down sequence by setting all power down bits, putting
the GPHY in reset, and finally cutting the 25Mhz reference clock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing a number of extra steps and delays to power-up the GPHY, update
the sequence to reflect the proper procedure here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for implementing the power down GPHY sequence, rename
bcmgenet_ephy_power_up to illustrate that it is not EPHY specific but
PHY agnostic, and add an "enable" argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_power_down() fails, we would want to propagate a return
value from bcmgenet_wol_power_down_cfg() to know about this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start-of-frame and end-of-frame bits were accidentally swapped.
In the current code it does not make any difference, since they are
always used together.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Home routers based on ARM SoCs like BCM4708 also have bcma bus with core
supported by bgmac.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Hardware Filter Block (HFB) so that incoming Rx traffic
can be matched and directed to desired Rx queues.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay the update of the TDMA producer index unless this is the last SKB
in a batch, or the queue is already stopped. Move the check for whether
the queue should be stopped before the xmit_more check to avoid locking
the transmit queue in case there was a SKB submitted which has xmit_more
set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have both bcmgenet_xmit_single() and
bcmgenet_xmit_frag() perform a free_bds decrement and a prod_index
increment by one. In case one of these functions fails to map a SKB or
fragment for transmit, we will return and exit bcmgenet_xmit() with an
error.
We can therefore safely use our local copy of nr_frags to know by how
much we should decrement the number of free buffers available, and by
how much the producer count must be incremented and do this in the tail
of bcmgenet_xmit().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bcmgenet_desc_rx() calls bcmgenet_rx_refill() at the end of
Rx packet processing loop, after the current Rx packet has already been
passed to napi_gro_receive(). However, bcmgenet_rx_refill() might fail
to allocate a new Rx skb, thus leaving a hole on the Rx queue where no
valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcmgenet_rx_refill() to retain the current Rx skb on the Rx
queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcmgenet_desc_rx() to call bcmgenet_rx_refill() at the top of
Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Jaedon Shin <jaedon.shin@gmail.com>--
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add struct bcmgenet_rx_ring to hold all necessary information
for a single Rx queue.
2. Add bcmgenet_init_rx_queues() to initialize all Rx queues.
3. Modify bcmgenet_init_rx_ring() to initialize a single Rx queue.
4. Modify Rx interrupt path code to use per-queue data.
5. Modify bcmgenet_rx_refill() to use RxCB->bd_addr.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple Rx queues:
1. Move the initialization of priv->num_rx_bds, priv->rx_bds, and
priv->rx_cbs from bcmgenet_init_rx_ring() to bcmgenet_init_dma()
since they are not specific to a single Rx queue. Mimics the Tx
init model where priv->num_tx_bds, priv->tx_bds, and priv->tx_cbs
are initialized in bcmgenet_init_dma().
2. Program DMA_MBUF_DONE_THRESH = 1 so that future Rx queues Q0-Q15
will get per-packet Rx interrupt.
3. Group DMA_START_ADDR, RDMA_READ_PTR, RDMA_WRITE_PTR, and DMA_END_ADDR
initialization together. Mimics the Tx init model.
4. There is 1-to-1 mapping between RxCBs and RxBDs.
Precalculate RxCB->bd_addr so that it can be used in the future.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple Rx queues, add GENET_Q16_RX_BD_CNT
and hw_params->rx_bds_per_q.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple Rx queues, adjust the call to
alloc_etherdev_mqs() to allow max GENET_MAX_MQ_CNT + 1 Rx queues.
The actual number of Rx queues in use is correctly adjusted with:
netif_set_real_num_rx_queues(priv->dev, priv->hw_params->rx_queues + 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet driver doesn't yet support multiple Rx queues.
Set hw_params->rx_queues = 0 accordingly.
The default Rx queue (Q16) is still created and operational.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.
This can be reproduced using the following sequence:
ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g
The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use c_index and ring->c_index to determine how many TxCBs/TxBDs are
ready for cleanup
- c_index = the current value of TDMA_CONS_INDEX
- TDMA_CONS_INDEX is HW-incremented and auto-wraparound (0x0-0xFFFF)
- ring->c_index = __bcmgenet_tx_reclaim() cleaned up to this point on
the previous invocation
2. Add bcmgenet_tx_ring->clean_ptr
- index of the next TxCB to be cleaned
- incremented as TxCBs/TxBDs are processed
- value always in range [ring->cb_ptr, ring->end_ptr]
3. Fix incrementing of dev->stats.tx_packets
- should be incremented only when tx_cb_ptr->skb != NULL
These changes simplify __bcmgenet_tx_reclaim(). Furthermore, Tx ring size
can now be any value.
With the old code, Tx ring size had to be a power-of-2:
num_tx_bds = ring->size;
c_index &= (num_tx_bds - 1);
last_c_index &= (num_tx_bds - 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.
Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag
stripping when the card cannot disable it. The driver should remove
NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed
for the ethtool.
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA
failures") added a few software maintained statistics using
BCM_SYSPORT_STAT_MIB_RX and BCM_SYSPORT_STAT_MIB_TX. These statistics are read
from the hardware MIB counters, such that bcm_sysport_update_mib_counters() was
trying to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCM_SYSPORT_STAT_SOFT, similar to
BCM_SYSPORT_STAT_NETDEV, such that bcm_sysport_get_ethtool_stats will read from
the software mib.
Fixes: 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma
failures") added a few software maintained statistics using
BCMGENET_STAT_MIB_RX and BCMGENET_STAT_MIB_TX. These statistics are read from
the hardware MIB counters, such that bcmgenet_update_mib_counters() was trying
to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCMGENET_STAT_SOFT, similar to
BCMGENET_STAT_NETDEV, such that bcmgenet_get_ethtool_stats will read from the
software mib.
Fixes: 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.
The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f ("tcp: refine TSO autosizing").
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_hw_params->bds_cnt and GENET_DEFAULT_BD_CNT are used only in Tx init.
Rename them accordingly:
- bcmgenet_hw_params->bds_cnt => bcmgenet_hw_params->tx_bds_per_q
- GENET_DEFAULT_BD_CNT => GENET_Q16_TX_BD_CNT
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is 1-to-1 mapping between TxCBs and TxBDs. Precalculate TxCB->bd_addr
once in bcmgenet_init_dma() instead of doing it over and over needlessly in
bcmgenet_get_txcb().
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Rename bcmgenet_init_multiq() to bcmgenet_init_tx_queues()
2. Fix bcmgenet_init_tx_queues() function description
3. Move Tx default queue init inside bcmgenet_init_tx_queues()
4. Modify bcmgenet_init_dma() to call bcmgenet_init_tx_queues()
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Simplify function description
2. Rename function parameter write_ptr to start_ptr to better indicate use
3. Remove unnecessary local variable first_bd
4. Remove out-of-place comment "Unclassified traffic goes to ring 16"
5. Fix TDMA_WRITE_PTR register init
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates BNX2 driver version to 2.2.6 and CNIC driver version
to 2.5.21.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not enable filter SORT MODE in chip init routine. This patch addresses an
issue where BCM5716 sporadically drops packets when changing multicast list.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides additional changes as a part of BNX2 and CNIC driver
re-branding effort.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_init_one() calls tg3_halt() without tp->lock despite its assumption
and causes deadlock.
If lockdep is enabled, a warning like this shows up before the stall:
[ BUG: bad unlock balance detected! ]
3.19.0test #3 Tainted: G E
-------------------------------------
insmod/369 is trying to release lock (&(&tp->lock)->rlock) at:
[<ffffffffa02d5a1d>] tg3_chip_reset+0x14d/0x780 [tg3]
but there are no more locks to release!
tg3_init_one() doesn't call tg3_halt() under normal situation but
during kexec kdump I hit this problem.
Fixes: 932f19de ("tg3: Release tp->lock before invoking synchronize_irq()")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Northstar (Broadcom's ARM architecture) we need to manually enable
all cores. Code for that is already in place, but the condition for it
was wrong.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
bnx2x_main.c:9172:6: warning: symbol 'bnx2x_stop_ptp' was not declared. Should it be static?
bnx2x_main.c:13321:6: warning: symbol 'bnx2x_register_phc' was not declared. Should it be static?
bnx2x_main.c:14638:5: warning: symbol 'bnx2x_enable_ptp_packets' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move init and deinit of PTP support from open/close functions
to probe/remove funcs to avoid removing/re-adding of associated PTP
device(s) during ifup/ifdown.
v2: tg3_ptp_init call moved to correct place (thx. Prashant)
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver load in tg3_init_one, if the driver detects DMA activity before
intializing the chip tg3_halt is called. As part of tg3_halt interrupts are
disabled using routine tg3_disable_ints. This routine was using mailbox value
which was not initialized (default value is 0). As a result driver was writing
0x00000001 to pci config space register 0, which is the vendor id / device id.
This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only
the Vendor ID to identify Configuration Request Retry). Also this issue is only
seen in older generation chipsets like 5722 because config space write to offset
0 from driver is possible. The newer generation chips ignore writes to offset 0.
Also without commit a7877b17a667, for these older chips when a GRC reset is
issued the Bootcode would reprogram the vendor id/device id, which is the reason
this bug was masked earlier.
Fixed by initializing the interrupt mailbox registers before calling tg3_halt.
Please queue for -stable.
Reported-by: Nils Holland <nholland@tisys.org>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do the following:
select FIXED_PHY if SYSTEMPORT=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()")
Fixes: a3862db2d3 ("net: systemport: hook SYSTEMPORT driver in the build")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do the following:
select FIXED_PHY if BCMGENET=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()")
Fixes: b0ba512e225d ("net: bcmgenet: enable driver to work without device tree"
Fixes: bdaa53bde5 ("net: bcmgenet: hook into the build system")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the calls to netdev_alloc_skb_ip_align in the
copybreak paths.
Cc: Gary Zambrano <zambrano@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook a ndo_set_mac_address callback, update the internal Ethernet MAC in
the netdevice structure, and finally write that address down to the
UniMAC registers. If the interface is down, and most likely clock gated,
we do not update the registers but just the local copy, such that next
ndo_open() call will effectively write down the address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-12-08
Please pull this last batch of pending wireless updates for the 3.19 tree...
For the wireless bits, Johannes says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
For the Bluetooth bits, Johan says:
"Here's one more bluetooth-next pull request for 3.19:
- Minor cleanups for ieee802154 & mac802154
- Fix for the kernel warning with !TASK_RUNNING reported by Kirill A.
Shutemov
- Support for another ath3k device
- Fix for tracking link key based security level
- Device tree bindings for btmrvl + a state update fix
- Fix for wrong ACL flags on LE links"
And...
"In addition to the previous one this contains two more cleanups to
mac802154 as well as support for some new HCI features from the
Bluetooth 4.2 specification.
From the original request:
'Here's what should be the last bluetooth-next pull request for 3.19.
It's rather large but the majority of it is the Low Energy Secure
Connections feature that's part of the Bluetooth 4.2 specification. The
specification went public only this week so we couldn't publish the
corresponding code before that. The code itself can nevertheless be
considered fairly mature as it's been in development for over 6 months
and gone through several interoperability test events.
Besides LE SC the pull request contains an important fix for command
complete events for mgmt sockets which also fixes some leaks of hci_conn
objects when powering off or unplugging Bluetooth adapters.
A smaller feature that's part of the pull request is service discovery
support. This is like normal device discovery except that devices not
matching specific UUIDs or strong enough RSSI are filtered out.
Other changes that the pull request contains are firmware dump support
to the btmrvl driver, firmware download support for Broadcom BCM20702A0
variants, as well as some coding style cleanups in 6lowpan &
ieee802154/mac802154 code.'"
For the NFC bits, Samuel says:
"With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca"
For the iwlwifi bits, Emmanuel says:
"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
And...
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
a infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
For the Atheros bits, Kalle says:
"Only ath10k changes this time and no major changes. Most visible are:
o new debugfs interface for runtime firmware debugging (Yanbo)
o fix shared WEP (Sujith)
o don't rebuild whenever kernel version changes (Johannes)
o lots of refactoring to make it easier to add new hw support (Michal)
There's also smaller fixes and improvements with no point of listing
here."
In addition, there are a few last minute updates to ath5k,
ath9k, brcmfmac, brcmsmac, mwifiex, rt2x00, rtlwifi, and wil6210.
Also included is a pull of the wireless tree to pick-up the fixes
originally included in "pull request: wireless 2014-12-03"...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our FW can support several fastpath HSI [for backward compatibility] but up
until now VFs were always configured to use latest fastpath HSI [although VF
driver might be older and use an older fastpath HSI].
For linux drivers, the differences are insignificant since driver never
utilized features that were overridden by the HSI change. But for VMs running
other operating systems this might be a problem.
In addition, eventually FW might change fastpath HSI in such a manner that
backward compatibility WILL break unless configured with proper version.
This patch fixes the issue for other operating system VMs, as well as lays
the ground work for forward compatibility in regard to the fastpath HSI.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 1G-SFP module detection by verifying not only that it's not
compliant with 10G-Ethernet, but also that it's 1G-ethernet compliant.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with GPHY revision G0, the GENET register layout has changed to
use the same numbering scheme as the Starfighter 2 switch. This means
that GPHY major revision is in bits 15:12, minor in bits 11:8 and patch
level is in bits 7:4.
Introduce a small heuristic which checks for the old scheme first, tests
for the new scheme and finally attempts to catch reserved values and
aborts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify bcmgenet driver so that it can be used on Broadcom 7xxx
MIPS-based STB platforms without a device tree.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake On Lan was not working on laptop DELL Vostro 1500.
If WOL was turned on, BCM4401 was powered up in suspend mode. LEDs blinked.
But the laptop could not be woken up with the Magic Packet. The reason for
that was that PCIE was not enabled as a system wakeup source and
therefore the host PCI bridge was not powered up in suspend mode.
PCIE was not enabled in suspend by PM because no child devices were
registered as wakeup source during suspend process.
On laptop BCM4401 is connected through the SSB bus, that is connected to the
PCI-Express bus. SSB and B44 did not use standard PM wakeup functions
and did not forward wakeup settings to their parents.
To fix that B44 driver enables PM wakeup and registers new wakeup source
using device_set_wakeup_enable(). Wakeup is automatically reported to the parent SSB
bus via power.wakeup_path. SSB bus enables wakeup for the parent PCI bridge, if there is any
child devices with enabled wakeup functionality. All other steps are
done by PM core code.
Signed-off-by: Andrey Skvortsov <Andrej.Skvortzov@gmail.com>
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook a nway_reset ethtool callback to allow restarting the
auto-negotiation process when asked to. We defer to the PHY library call
to do the heavy lifting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow enabling and disabling EEE using the designated ethtool getters
and setters. GENET allows controlling EEE at the UniMAC, RBUF and TBUF
levels. We also take care of restoring EEE after a suspend/resume cycle
if it was enabled prior to suspending.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register definitions to control EEE in the UniMAC, RBUF and TBUF
register ranges.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help troubleshoot heavy memory pressure conditions, add a bunch of
statistics counter to log RX buffer allocation and RX/TX DMA mapping
failures. These are reported like any other counters through the ethtool
stats interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help troubleshoot heavy memory pressure conditions, add a bunch of
statistics counter to log RX buffer allocation and RX/TX DMA mapping
failures. These are reported like any other counters through the ethtool
stats interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. bcm_sysport_tx_poll()
always returns 0 whether or not we completed the poll quantum.
Fix this by returning either 0 when we did complete the TX ring reclaim,
or budget to trigger a repoll.
Fixes: d75b1ade56 ("net: less interrupt masking in NAPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.
Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_msix_fp_int() and bnx2x_interrupt() run from hard interrupt
context.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove the rcu_read_lock/unlock around rcu_access_pointer
2. Replace the rcu_dereference with rcu_access_pointer
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sysport_resume() was missing an UniMAC reset which can lead to
various receive FIFO corruptions coming out of a suspend cycle. If the
RX FIFO is stuck, it will deliver corrupted/duplicate packets towards
the host CPU interface.
This could be reproduced on crowded network and when Wake-on-LAN is
enabled for this particular interface because the switch still forwards
packets towards the host CPU interface (SYSTEMPORT), and we had to leave
the UniMAC RX enable bit on to allow matching MagicPackets.
Once we re-enter the resume function, there is a small window during
which the UniMAC receive is still enabled, and we start queueing
packets, but the RDMA and RBUF engines are not ready, which leads to
having packets stuck in the UniMAC RX FIFO, ultimately delivered towards
the host CPU as corrupted.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a small window during which the SYSTEMPORT adapter
enables its RX interrupts without having enabled its NAPI handler, which
can result in packets to be discarded during interface bringup.
A similar but more serious window exists in bcm_sysport_resume() during
which we can have the RDMA engine not fully prepared to receive packets
and yet having RX interrupts enabled.
Fix this my moving the RX interrupt enable down to
bcm_sysport_netif_start() after napi_enable() for the RX path is called,
which fixes both call sites: bcm_sysport_open() and
bcm_sysport_resume().
Fixes: b02e6d9ba7 ("net: systemport: add bcm_sysport_netif_{enable,stop}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ring TX doorbell only if xmit_more is not set or the queue is stopped.
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple enable_irq_wake() calls will keep increasing the IRQ
wake_depth, which ultimately leads to the following types of
situation:
1) enable Wake-on-LAN interrupt w/o password
2) enable Wake-on-LAN interrupt w/ password
3) enable Wake-on-LAN interrupt w/o password
4) disable Wake-on-LAN interrupt
After step 4), SYSTEMPORT would always wake-up the system no matter what
wake-up device we use, which is not what we want. Fix this by making
sure there are no unbalanced enable_irq_wake() calls.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple enable_irq_wake() calls will keep increasing the IRQ
wake_depth, which ultimately leads to the following types of
situation:
1) enable Wake-on-LAN interrupt w/o password
2) enable Wake-on-LAN interrupt w/ password
3) enable Wake-on-LAN interrupt w/o password
4) disable Wake-on-LAN interrupt
After step 4), GENET would always wake-up the system no matter what
wake-up device we use, which is not what we want. Fix this by making
sure there are no unbalanced enable_irq_wake() calls.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b629be5c83 ("net: bcmgenet: check
harder for out of memory conditions") moved the increment of the local
read pointer *before* reading from the hardware descriptor using
dmadesc_get_length_status(), which creates an off-by-one situation.
Fix this by moving again the read_ptr increment after we have read the
hardware descriptor to get both the control block and the read pointer
back in sync.
Fixes: b629be5c83 ("net: bcmgenet: check harder for out of memory conditions")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GENET MAC has three Tx ring priority registers:
- GENET_x_TDMA_PRIORITY0 for queues 0-5
- GENET_x_TDMA_PRIORITY1 for queues 6-11
- GENET_x_TDMA_PRIORITY2 for queues 12-16
Fix bcmgenet_init_multiq() to program them correctly.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_mii_setup() is called from the PHY state machine every 1-2 seconds
when the PHYs are in PHY_POLL mode.
Improve bcmgenet_mii_setup() so that it touches the MAC registers only when
the link is up and there was a change to link, speed, duplex, or pause status.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit bc23333ba1 ("net:
bcmgenet: fix bcmgenet_put_tx_csum()"), we need to return the skb
pointer in case we had to reallocate the SKB headroom.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_put_tx_csum() needs to return skb pointer back to the caller
because it reallocates a new one in case of lack of skb headroom.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_wol_resume() is only used in bcmgenet_resume(), which is only
defined when CONFIG_PM_SLEEP is enabled. This leads to the following
compile warning when building with !CONFIG_PM_SLEEP:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1967:12: warning: ‘bcmgenet_wol_resume’ defined but not used [-Wunused-function]
Since bcmgenet_resume() is the only user of bcmgenet_wol_resume(), fix
this by directly inlining the function there.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be manipulaging the DMA_CTRL registers directly by writing
0 to them to disable DMA. This is an operation that needs to be timed to
make sure the DMA engines have been properly stopped since their state
machine stops on a packet boundary, not immediately.
Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to
ensure a proper DMA engine state. As a result, we need to reorder the
function bodies to resolve the use dependency.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz