of_map_mode is needed so to be possible to set initial regulators mode from
the board DTS. Otherwise, for DT boot, regulators are left in their default
state after reset/reboot. Document device specific modes as well.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mixing raw voltage and selector based regulator ops is
inconsistent. This driver already supports some selector based
ops via the list_voltage and set_voltage_time_sel ops but it uses
raw voltage ops for get_voltage and set_voltage. This causes
problems for regulator_set_voltage() and automatic insertion of
slewing delays because set_voltage_time_sel() is only used if the
regulator ops are all selector based. Put another way, delays
aren't happening at all right now when we should be waiting for
voltages to settle. Let's move to pure selector based regulator
ops so that the delays are inserted properly.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only the FT SMPS type regulators have slewing supported in the
driver, but all types of SMPS regulators need the same support.
The only difference is that some SMPS regulators don't have a
step size and the step delay is typically 20, not 8. Luckily, the
step size reads as 0 for the non-FT types, so we can always read
that, but we need to detect which type of regulator we're using
to figure out what step delay to use. Make these minor
adjustments to the slew rate calculations and add support for the
delay function to the appropriate regulator ops.
Reported-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5e3ca2b349 ("regulator: Try to resolve regulators supplies on
registration") added a call to regulator_resolve_supply() within
regulator_register() where the regulator_list_mutex is held. This causes
a deadlock to occur on the Tegra114 Dalmore board when the palmas PMIC
is registered because regulator_register_resolve_supply() calls
regulator_dev_lookup() which may try to acquire the regulator_list_mutex
again.
Fix this by releasing the mutex before calling
regulator_register_resolve_supply() and update the error exit path to
ensure the mutex is released on an error.
[Made commit message more legible -- broonie]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Flagging voltage changes as possible for exactly specified voltages
appears to be triggering bugs in the SDHCI code (it should be able to
handle the case where only one voltage it wants is in the range it is
allowed to set) so make sure we only set the flag in cases where there's
genuine variability.
Signed-off-by: Mark Brown <broonie@kernel.org>
This aids in debugging problems triggered by the regulator core applying
its constraints, we could potentially crash immediately after updating
the voltage if the constraints are buggy.
Signed-off-by: Mark Brown <broonie@kernel.org>
This can be used to expose the act8600 registers via debugfs.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the code easier to read and it avoids a dynamic memory
allocation.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most Maxim PMIC regulator drivers are for sub-devices of Multi-Function
Devices with drivers under drivers/mfd. But for many of these, the same
object file name was used for both the MFD and the regulator drivers.
Having 2 different drivers with the same name causes a lot of confusion
to Kbuild, specially if these are built as module since only one module
will be installed and also exported symbols will be undefined due being
overwritten by the other module during modpost.
For example, it fixes the following issue when both drivers are module:
$ make M=drivers/regulator/
...
CC [M] drivers/regulator//max14577.o
Building modules, stage 2.
MODPOST 1 modules
WARNING: "maxim_charger_calc_reg_current" [drivers/regulator//max14577.ko] undefined!
WARNING: "maxim_charger_currents" [drivers/regulator//max14577.ko] undefined!
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
moved the regulator supplies lookup logic from the regulators registration
to the regulators get time.
Unfortunately, that changed the behavior of the regulator core since now a
parent supply with a child regulator marked as always-on, won't be enabled
unless a client driver attempts to get the child regulator during boot.
This patch tries to resolve the parent supply for the already registered
regulators each time that a new regulator is registered. So the regulators
that have child regulators marked as always on will be enabled regardless
if a driver gets the child regulator or not.
That was the behavior before the mentioned commit, since parent supplies
were looked up at regulator registration time instead of during child get.
Since regulator_resolve_supply() checks for rdev->supply, most of the times
it will be a no-op. Errors aren't checked to keep the possible out of order
dependencies which was the motivation for the mentioned commit.
Also, the supply being available will be enforced on regulator get anyways
in case the resolve fails on regulators registration.
Fixes: 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # 4.1+
On some designs, a handful of the regulators can't be read via
SPMI transactions because they're "secure" and not intended to be
touched by non-secure processors. This driver unconditionally
attempts to read the id registers of all the regulators though,
leading to probe failing and no regulators being registered.
Let's ignore any errors from failing to read the registers and
keep adding other regulators so that this driver can probe on
such devices.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the regulators available on pm8994 and add support for
this PMIC to the SPMI PMIC regulator driver.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When machine constraints are applied, regulator framework first sets
initial mode (if any) and then enables the regulator if needed. The current
code in twl4030reg_set_mode always checks if the regulator is enabled
before applying the mode. That results in -EACCES error returned for
"always-on" regulators which have "initial-mode" set in the board DTS. Fix
that by removing the unneeded check.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the TRM, we need to enable i2c access to powerbus before
writing to it. Also, a new write to powerbus should not be attempted if
there is a pending transfer. The current code does not implement that
functionality and while there are no known problems caused by that, it is
better to follow what TRM says.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Currently we only attempt to set the voltage during constraints
application if an exact voltage is specified. Extend this so that if
the currently set voltage for the regulator is outside the bounds set in
constraints we will move the voltage to the nearest constraint, raising
to the minimum or lowering to the maximum as needed. This ensures that
drivers can probe without the hardware being driven out of spec.
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently due to a wrongly resolved merge conflict between two
branches, which contained the same commit, the commit contents
partially was added two times in a row.
This change reverts the latter wrong inclusion of commit 909f7ee0b5
("regulator: core: Add support for active-discharge configuration").
The first applied commit 670666b9e0 ("regulator: core: Add support
for active-discharge configuration") is not touched.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the core to always use the voltage constraints to set the voltage
on startup. A forthcoming change in that code will ensure that we bring
out of constraints voltages into spec with this setting.
Signed-off-by: Mark Brown <broonie@kernel.org>
The check would dereference pdata, which can be NULL in the non-DT
use case.
Nothing will break if pdata->num_regulators is larger than the number
of regulators that the driver defines: pdata->num_regulators is only
read in act8865_get_init_data() to iterate through pdata->regulators.
The error handler might have some value as a sanity check on the
platform data, but the platform data could be broken in many other
ways that are not checked for (unknown IDs, duplicate IDs), so I see
no reason to perform only this specific check.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The local variable "dev" already contains a pointer to the device,
so there is no need to take the address of "client->dev" again.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_resolve_supply() function checks if a supply has been
associated with a regulator to avoid enabling it if that is not the
case.
But the supply was already looked up with regulator_resolve_supply()
and set with set_supply() before the check and both return on error.
So the fact that this statement has been reached means that neither
of them failed and a supply must be associated with the regulator.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
At boot time the regulator driver can be initialized before the
gpio, in which case the call to of_get_named_gpio will return
EPROBE_DEFER. This value is silently passed to regulator_register
which will return success, although the gpio is not registered
(regulator_ena_gpio_request not called) as the value passed is
detected as invalid. The gpio_regulator_probe will therefore
succeed win no gpio requested.
Signed-off-by: Mihai Mihalache <mihai.d.mihalache@intel.com>
Reviewed-by: Hans Holmberg <hans.holmberg@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prints the error number along with error message when any
error occurs. This help on getting the reason of failure
quickly from log without any code instrument.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of platforms like Nvidia's Tegra210 Jetson-TX1 platform has
multiple PMW based regulators. Add support to have multiple instances
of the driver by not changing any global data of pwm regulator and
if required, making instance specific copy and then making changes.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With following equation for calculating
voltage_to_duty_cycle_percentage
100 - (((req_uV * 100) - (min_uV * 100)) / diff);
we get 0% for max_uV and 100% for min_uV.
Correcting this to
((req_uV * 100) - (min_uV * 100)) / diff;
to get proper duty cycle.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OF interface provides to read the u32 value via standard interface
of_property_read_u32(). Use this API to read "regulator-min-microvolts"
and "regulator-max-microvolt".
This will make consistent with other property value reads.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch to fix incorrect clear of event register.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch to fix incorrect clear of event register.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator ops callback for configuration of active-discharge
and provide necessarily information via regulator descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper function to set the state of active-discharge of
regulator using regmap. The HW regulator driver can directly
use this by providing the necessary information in the regulator
descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The documentation lists both 1.8V and 3.3V for this regulator output,
but 3.3V is mentioned more often and also matches what JZ4770 and
JZ4780 expect as an input.
Note that the voltage of REG9 is not programmable, so this commit only
changes the voltage reported in sysfs and debugfs, not the actual
output voltage of the hardware.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to preserve its value between calls. I guess this
was a copy-paste slip-up.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These fields are never used and not required at all, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This problem was introduced by:
commit daad134d66 ("regulator: core: Request GPIO before creating
sysfs entries")
The error path was not updated correctly after moving GPIO registration
code and in case regulator_ena_gpio_free failed, device_unregister() was
called even though device_register() was not yet called.
This problem breaks the boot at least on all Tegra 32-bit devices. It
will also crash each device that specifices GPIO that is unavaiable at
regulator_register call. Here's error log I've got when forced GPIO to
be invalid:
[ 1.116612] usb-otg-vbus-reg: Failed to request enable GPIO10: -22
[ 1.122794] Unable to handle kernel NULL pointer dereference at
virtual address 00000044
[ 1.130894] pgd = c0004000
[ 1.133598] [00000044] *pgd=00000000
[ 1.137205] Internal error: Oops: 5 [#1] SMP ARM
and here's backtrace from KDB:
Exception stack(0xef11fbd0 to 0xef11fc18)
fbc0: 00000000 c0738a14 00000000 00000000
fbe0: c0b2a0b0 00000000 00000000 c0738a14 c0b5fdf8 00000001 ef7f6074 ef11fc4c
fc00: ef11fc50 ef11fc20 c02a8344 c02a7f1c 60000013 ffffffff
[<c010cee0>] (__dabt_svc) from [<c02a7f1c>] (kernfs_find_ns+0x18/0xf8)
[<c02a7f1c>] (kernfs_find_ns) from [<c02a8344>] (kernfs_find_and_get_ns+0x40/0x58)
[<c02a8344>] (kernfs_find_and_get_ns) from [<c02ac4a4>] (sysfs_unmerge_group+0x28/0x68)
[<c02ac4a4>] (sysfs_unmerge_group) from [<c044389c>] (dpm_sysfs_remove+0x30/0x5c)
[<c044389c>] (dpm_sysfs_remove) from [<c0436ba8>] (device_del+0x48/0x1f4)
[<c0436ba8>] (device_del) from [<c0436d84>] (device_unregister+0x30/0x6c)
[<c0436d84>] (device_unregister) from [<c0403910>] (regulator_register+0x6d0/0xdac)
[<c0403910>] (regulator_register) from [<c04052d4>] (devm_regulator_register+0x50/0x84)
[<c04052d4>] (devm_regulator_register) from [<c0406298>] (reg_fixed_voltage_probe+0x25c/0x3c0)
[<c0406298>] (reg_fixed_voltage_probe) from [<c043d21c>] (platform_drv_probe+0x60/0xb0)
[<c043d21c>] (platform_drv_probe) from [<c043b078>] (driver_probe_device+0x24c/0x440)
[<c043b078>] (driver_probe_device) from [<c043b5e8>] (__device_attach_driver+0xc0/0x120)
[<c043b5e8>] (__device_attach_driver) from [<c043901c>] (bus_for_each_drv+0x6c/0x98)
[<c043901c>] (bus_for_each_drv) from [<c043ad20>] (__device_attach+0xac/0x138)
[<c043ad20>] (__device_attach) from [<c043b664>] (device_initial_probe+0x1c/0x20)
[<c043b664>] (device_initial_probe) from [<c043a074>] (bus_probe_device+0x94/0x9c)
[<c043a074>] (bus_probe_device) from [<c043a610>] (deferred_probe_work_func+0x80/0xcc)
[<c043a610>] (deferred_probe_work_func) from [<c01381d0>] (process_one_work+0x158/0x454)
[<c01381d0>] (process_one_work) from [<c013854c>] (worker_thread+0x38/0x510)
[<c013854c>] (worker_thread) from [<c013e154>] (kthread+0xe8/0x104)
[<c013e154>] (kthread) from [<c0108638>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_attr_is_visible (which is a .is_visible callback of
regulator_dev_group attribute_grpup) checks rdev->ena_pin to decide if
"status" file should be present in sysfs. This field is set at the end
of regulator_ena_gpio_request so it has to be called before
device_register() otherwise this test will always fail, causing "status"
file to not be visible.
Since regulator_attr_is_visible also tests for is_enabled() op, this
problem is only visible for regulators that does not define this
callback, like regulator-fixed.c.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't print out an error with the driver sees EPROBE_DEFER when
attempting to get the gpio. These errors are usually transient; the
probe will be retried later.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the s2mps11_info.rdev_num because it is not used outside of
probe.
Suggested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_master_send() returns the number of bytes written on success.
So current code returns 2 if ad5398_write_reg() success.
This return value is propagated to .set_current_limit, .enable and .disable
callbacks of regulator_ops. This can be a problem, for example, if the
users test if the return value of regulator_set_current_limit() is 0.
Fix it by making ad5398_write_reg() return 0 on success.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAXIM Semiconductor's PMIC, MAX77620 and MAX20024 have the
multiple DCDC and LDOs. This supplies the power to different
components of the system.
Also these rails has configuration for ramp time, flexible
power sequence, slew rate etc.
Add regulator driver to access these rails via regulator APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Following BUILD_BUG_ON using a variable fails for some of the compilers
and optimization levels (reported for gcc 4.9):
var = ARRAY_SIZE(s2mps15_regulators);
BUILD_BUG_ON(S2MPS_REGULATOR_MAX < var);
Fix this by using ARRAY_SIZE directly.
Additionally add missing BUILD_BUG_ON check for S2MPS15 device (the
check ensures that internal arrays are big enough to hold data for all
of regulators on all devices).
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:
drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.
In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c4c60554a ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap")
Signed-off-by: Mark Brown <broonie@kernel.org>
The vexpress regulator implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in hardware monitors.
This patch renames the vexpress regulator implementation to
vexpress-regulator so that there will be no clash in the module namespace.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally the helper macros used uppercase regulator names, which
are primarily used to expand to the regulator ID enum, as the default
names. This is aestheticly unpleasent.
Since the of_match bits are the same, just lowercase, use that as the
default names instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the regulator driver for hi655x PMIC.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's perfectly valid to use the LTC3589 without an interrupt pin
connected to it. Currently, the driver probing fails when client->irq
is 0 (which means "no interrupt"). Don't register the interrupt
handler in that case but successfully finish the device probing instead.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max77686 and max77802 regulator drivers are for sub-devices of a MFD
driver for some PMIC blocks. But the same object file name (max77686.o)
was used for both the common MFD driver and the max77686 regulator one.
This confuses kbuild if both drivers are built as module causing the MFD
driver to not be copied when installing the modules.
Also, max77{686,802} are a quite generic name for MFD subdevices drivers
so it is better to rename them to max77{686,802}-regulator like it's the
case for most regulator drivers.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for TPS65912 PMIC regulators.
The regulators set consists of 4 DCDCs and 10 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
LP872x regulators are made active via the EN pin, which might be hooked to a
GPIO. This adds support for driving the GPIO high when the driver is in use.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices don't hook the DVS pin to a GPIO but to ground or VCC.
In those cases, it is not a problem to have no DVS GPIO provided, as the current
code will already switch to software-only DVS selection:
When the DVS GPIO is invalid, lp872x_init_dvs jumps to the set_default_dvs_mode
label, which instructs the chip not to use the DVS pin at all and do it all in
software instead (by clearing the LP8720_EXT_DVS_M bit in the
LP872X_GENERAL_CFG register).
That is reflected later in the code, when setting the bucks (the DVS pin only
applies to the bucks) by checking for the LP8720_EXT_DVS_M bit on the
LP872X_GENERAL_CFG register (in lp872x_select_buck_vout_addr) to decide whether
to use software or hardware DVS selection.
Thus, there is no need to print a warning when the DVS GPIO is invalid.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds new regulator driver to support ACT8945A MFD
chip's regulators.
The ACT8945A has three step-down DC/DC converters and four
low-dropout regulators.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AXP20X datasheet lists the possible voltage settings for LDO4, so
it was implemented using a voltage table. Upon closer examination,
the valid voltages can be mapped into 3 linear ranges.
Move AXP20X LDO4 to use linear ranges. The supporting code can be
reused with later AXP8xx PMICs, which have a number of regulators
that have 2 linear ranges.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch-type regulators, such as DC1SW on AXP22X, are a secondary output
from DCDC1. They are just an on/off switch, and the driver should not
try to read its voltage directly from the DCDC1 control registers.
Instead, the core will pass down the voltage from the regulator supply
chain.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Documentation/devicetree/bindings/regulator/mt6397-regulator.txt doc
mentions that a compatible "mediatek,mt6397-regulator" is required for
the MT6397 device node but the driver doesn't provide a OF match table so
the platform bus .match fallbacks to match using the driver name instead.
This also means that module auto-loading is broken for this driver since
the MFD driver that register the device, has a .of_compatible set so the
platform .uevent callback reports a OF modalias that's not in the module.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform bus_type .match callback attempts to match the platform device
name with an entry on the .id_table if provided and fallbacks to match with
the driver's name if a table is not provided.
Using a platform device ID to match is more explicit, allows the driver to
support more than one device and also the MODULE_DEVICE_TABLE macro can be
used to export the module aliases information instead of the MODULE_ALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we now free the constraints in regulator_dev_release we will still
call free on the constraints pointer even if we went down an error
path in regulator_register, because it is only allocated after the
device_register. As such we no longer need to free rdev->constraints
on the error paths, so this patch removes said frees.
Fixes: 29f5f4860a ("regulator: core: Move more deallocation into class unregister")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Aside from a fix for a spurious warning (which caused more problems than
it fixed in the fixing really) this is all driver updates, including new
drivers for Dialog PV88060/90 and TI LM363x and TPS65086 devices. The
qcom_smd driver has had PM8916 and PMA8084 support added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWlUWiAAoJECTWi3JdVIfQtywH/0joibyUbL34arXcPNCUUhlo
UnhTgT1kfOoS01ODt9gU49X4/8SRL9HdjcrIV8yTz4Ldb8by8Rd3ZrkO//9zs7BF
5PIqIzEw6FT/Ovsj8Tc35irccMSrwtTIGRrA8zrM/WtWQWcIUWFxMw+j/lewIvvH
jHZNTTLL5XemObSTfvzhbS6PZ8RcvRVXLNJjZYYO5xAEHNg3i5Hxao5p3QKzVJ8m
P5n4jSiTY/pVePcs9dzzQTGjlzkE11KX7DBxnmXOSPZsArSaRIC53DCmqu/JoG+o
3JJBkmRx7IJb0651hclFaUl8Wl56FSst+zigeAj82b301xpVR30iG3xiwYK/AT8=
=NQ6n
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Aside from a fix for a spurious warning (which caused more problems
than it fixed in the fixing really) this is all driver updates,
including new drivers for Dialog PV88060/90 and TI LM363x and TPS65086
devices. The qcom_smd driver has had PM8916 and PMA8084 support
added"
* tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: core: remove some dead code
regulator: core: use dev_to_rdev
regulator: lp872x: Get rid of duplicate reference to DVS GPIO
regulator: lp872x: Add missing of_match in regulators descriptions
regulator: axp20x: Fix GPIO LDO enable value for AXP22x
regulator: lp8788: constify regulator_ops structures
regulator: wm8*: constify regulator_ops structures
regulator: da9*: constify regulator_ops structures
regulator: mt6311: Use REGCACHE_RBTREE
regulator: tps65917/palmas: Add bypass ops for LDOs with bypass capability
regulator: qcom-smd: Add support for PMA8084
regulator: qcom-smd: Add PM8916 support
soc: qcom: documentation: Update SMD/RPM Docs
regulator: pv88090: logical vs bitwise AND typo
regulator: pv88090: Fix irq leak
regulator: pv88090: new regulator driver
regulator: wm831x-ldo: Use platform_register/unregister_drivers()
regulator: wm831x-dcdc: Use platform_register/unregister_drivers()
regulator: lp8788-ldo: Use platform_register/unregister_drivers()
regulator: core: Fix nested locking of supplies
...
Setting the set_suspend_enable/disable callback to support
enable and disable the dcdc when system is suspend.
Signed-off-by: zhangqing <zhangqing@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally queue_delayed_work() used to negative error codes or 0 and 1
on success depending if the work was queued or not. It caused a lot of
bugs where people treated all non-zero returns as failures so we changed
it to return bool instead in d4283e9378 ('workqueue: make queueing
functions return bool'). Now it never returns failure.
Checking for negative values causes a static checker warning since it is
impossible based on the bool type.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The lp872x structure holds a reference to the DVS GPIO, but it is never actually
used anywhere, since a first reference exists from the lp872x_dvs structure.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to select the regulators via of_find_regulator_by_node (and thus use
them in devicetree), defining of_match for each regulator is required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The enable/disable values for GPIO LDOs are reversed. It seems no one
noticed as AXP22x support was introduced recently, and no one was using
the GPIO LDOs, either because no designs actually use them or board
support hasn't caught up.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This regulator is on a slow i2c bus. Register accesses are very simple,
they all either enable/disable a regulator channel, or select a new
voltage level. Thus, reading registers from the device will always
return what was last written.
Therefore we can save a lot of time when reading registers by using a
regmap_cache. Since the register map is relatively large, but we only
ever access a few of them, we use an RBTREE cache.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
set/get_bypass ops were missing for ldo1/ldo2 on tps65917 and
ldo9 on palmas/tps659038 which support bypass mode.
Adding the bypass ops helps consumers configure these ldos in
bypass mode or remove bypass mode if need be.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support and documentation for the PMA8084 regulators
found on APQ8084 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support and documentation for the PM8916 regulators
found on MSM8916 platforms.
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These were supposed to be bitwise AND instead of logical. Also kernel
style is for the operator to be on the first line and I removed some
extra parenthesis.
Fixes: c90456e36d ('regulator: pv88090: new regulator driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88090 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fa731ac7ea ("regulator: core: avoid unused variable warning")
introduced a subtle change in how supplies are locked. Where previously
code was always locking the regulator of the current iteration, the new
implementation only locks the regulator if it has a supply. For any
given power tree that means that the root will never get locked.
On the other hand the regulator_unlock_supply() will still release all
the locks, which in turn causes the lock debugging code to warn about a
mutex being unlocked which wasn't locked.
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Fixes: Fixes: fa731ac7ea ("regulator: core: avoid unused variable warning")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The latest workaround for the lockdep interface's not using the second
argument of mutex_lock_nested() changed the loop missed locking the last
regulator due to a thinko with the loop termination condition exiting
one regulator too soon.
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make changes to allow this driver to work with the updated TPS65086 core
driver and bindings.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There were some missing "ret = " assignments here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As noticed by Geert Uytterhoeven, my patch to avoid a harmless build warning
in regulator_lock_supply() was total crap and introduced a real bug:
> [ BUG: bad unlock balance detected! ]
> kworker/u4:0/6 is trying to release lock (&rdev->mutex) at:
> [<c0247b84>] regulator_set_voltage+0x38/0x50
we still lock the regulator supplies, but not the actual regulators,
so we are missing a lock, and the unlock is unbalanced.
This rectifies it by first locking the regulator device itself before
using the same loop as before to lock its supplies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 716fec9d1965 ("[SUBMITTED] regulator: core: avoid unused variable warning")
Signed-off-by: Mark Brown <broonie@kernel.org>
LM363X regulator driver supports LM3631 and LM3632.
LM3631 has 5 regulators. LM3632 provides 3 regulators.
One boost output and LDOs are used for the display module.
Boost voltage is configurable but always on.
Supported operations for LDOs are enabled/disabled and voltage change.
Two LDOs of LM3632 can be controlled by external pins.
Those are configured through the DT properties.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for TPS65218 LS3 current regulator, which is capable of 4
current input limit modes: 100, 200, 500, and 1000 uA.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently S2MPSXX multifunction device is named as *-pmic,
and these MFDs also supports regulator as a one of its MFD cell which
has the same name, because current name is confusing and we want to
sort it out.
We did discussed different approaches about how the MFD and it
cells need to be named here [1].
Based in the discussion this patch rename MFD regulator name as
*-regulator instead of current *-pmic.
This patch also changes the corresponding entries in the regulator driver
to keep git-bisect happy.
[1]-> https://lkml.org/lkml/2015/10/28/417
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS15 PMIC is similar in functionality to S2MPS11/14 PMIC. It contains
27 LDO and 10 Buck regulators and allows programming these regulators via a
I2C interface. This patch adds initial support for LDO/Buck regulators of
S2MPS15 PMIC.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the driver for the Powerventure PV88060 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The second argument of the mutex_lock_nested() helper is only
evaluated if CONFIG_DEBUG_LOCK_ALLOC is set. Otherwise we
get this build warning for the new regulator_lock_supply
function:
drivers/regulator/core.c: In function 'regulator_lock_supply':
drivers/regulator/core.c:142:6: warning: unused variable 'i' [-Wunused-variable]
To avoid the warning, this restructures the code to make it
both simpler and to move the 'i++' outside of the mutex_lock_nested
call, where it is now always used and the variable is not
flagged as unused.
We had some discussion about changing mutex_lock_nested to an
inline function, which would make the code do the right thing here,
but in the end decided against it, in order to guarantee that
mutex_lock_nested() does not introduced overhead without
CONFIG_DEBUG_LOCK_ALLOC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9f01cd4a91 ("regulator: core: introduce function to lock regulators and its supplies")
Link: http://permalink.gmane.org/gmane.linux.kernel/2068900
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 7e50711993 ("mfd: tps6105x: Use i2c regmap to access
registers"), we can use regmap helper functions instead of open coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it possible to use the bulk API with optional supplies, by allowing
the consumer to marking supplies as optional in the regulator_bulk_data.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix the below build error:
drivers/regulator/mt6311-regulator.c:111: undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add support for TPS65086 PMIC regulators.
The regulators set consists of 3 Step-down Controllers, 3 Step-down
Converters, 3 LDOs, 3 Load Switches, and a Sink and Source LDO. The
output voltages are configurable and are meant to supply power to a
SoC and/or other components.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Since we need to read voltages of parents as part of setting supply
voltages we need to be able to do get_voltage() internally without
taking locks so reorganize the locking to take locks on the full tree on
entry rather than as we recurse when called externally.
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver depends on MFD_STW481X but there isn't a build dependency so
it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The set_load() op deals with uA while the SMD packets used mA, so
convert as we're building the packet.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Until now changing the voltage of a regulator only ever effected the
regulator itself, but never its supplies. It's a common pattern though
to put LDO regulators behind switching regulators. The switching
regulators efficiently drop the input voltage but have a high ripple on
their output. The output is then cleaned up by the LDOs. For higher
energy efficiency the voltage drop at the LDOs should be minimized. For
this scenario we need to propagate the voltage change to the supply
regulators. Another scenario where voltage propagation is desired is
a regulator which only consists of a switch and thus cannot regulate
voltages itself. In this case we can pass setting voltages to the
supply.
This patch adds support for voltage propagation. We do voltage
propagation when the current regulator has a minimum dropout voltage
specified or if the current regulator lacks a get_voltage operation
(indicating it's a switch and not a regulator).
Changing the supply voltage must be done carefully. When we are
increasing the current regulators output we must first increase the
supply voltage and then the regulator itself. When we are decreasing the
current regulators voltage we must decrease the supply voltage after
changing the current regulators voltage.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
_regulator_call_set_voltage has code to translate a minimum/maximum
voltage pair into a selector. This code is useful for others aswell,
so create a regulator_map_voltage function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The anatop regulators are SoC internal LDO regulators usually supplied
by an external PMIC. This patch adds support for specifying the supply
from the device tree using the vin-supply property.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The unlocked version will be needed when we start propagating voltage
changes to the supply regulators.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The LDO1 driver is using the arizona_of_get_named_gpio helper function
which will return 0 if an error was encountered whilst parsing the GPIO,
as under the pdata scheme 0 was not being treated as a valid GPIO.
However, since the regulator framework was expanded to allow the use of
GPIO 0 this causes us to attempt to register GPIO 0 when we encountered
an error parsing the device tree.
This patch uses of_get_named_gpio directly and sets the
ena_gpio_initialized flag based on the return value.
Fixes: 1de3821ace ("regulator: Set ena_gpio_initialized in regulator drivers")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide an additional case entry for DA9053_BC in the find_regulator_info()
function in order to support BC type silicon for the DA9053 device.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DC1SW and DC5LDO regulators in the AXP22X are internally chained
to DCDC1 and DCDC5, hence the names. The original bindings used the
parent regulator names for the supply regulator property.
Since they are internally connected, the relationship should not be
represented in the device tree, but handled internally by the driver.
This patch has the driver remember the regulator names for the parent
DCDC1/DCDC5, and use them as supply names for DC1SW/DC5LDO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch modifies tps6105x and associated function driver to use regmap
instead of operating directly on i2c.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For the step-down DC/DC regulators, the output voltage is
selectable by setting VSEL pin that when VSEL is low, output
voltage is programmed by VSET1[] bits, and when VSEL is high,
output voltage is programmed by VSET2[] bits.
The DT property "active-semi,vsel-high" is used to specify
the VSEL pin at high on the board.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The unlocked version will be needed when we start propagating voltage
changes to the supply regulators.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each regulator_dev is locked with its own mutex. This is fine as long
as only one regulator_dev is locked, but makes lockdep unhappy when we
have to walk up the supply chain like it can happen in
regulator_get_voltage:
regulator_get_voltage ->
mutex_lock(®ulator->rdev->mutex) ->
_regulator_get_voltage(regulator->rdev) ->
regulator_get_voltage(rdev->supply) ->
mutex_lock(®ulator->rdev->mutex);
This causes lockdep to issue a possible deadlock warning.
There are at least two ways to work around this:
- We can always lock the whole supply chain using the functions
introduced with this patch.
- We could store the current voltage in struct regulator_rdev so
that we do not have to walk up the supply chain for the
_regulator_get_voltage case.
Anyway, regulator_lock_supply/regulator_unlock_supply will be needed
once we allow regulator_set_voltage to optimize the supply voltages.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When resolving regulator-regulator supplies we ignore probe deferral
returns from regulator_dev_lookup() (such as are generated for DT when
we can see a supply is registered) and just fall back to the dummy
regulator if there are full constraints (as is the case for DT). This
means that probe deferral is broken for DT systems, fix that by paying
attention to -EPROBE_DEFER return codes like we do -ENODEV.
A further patch will simplify this further, this is a minimal fix for
the specific issue.
Fixes: 9f7e25edb1 (regulator: core: Handle full constraints systems when resolving supplies)
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonnie@kernel.org>
Cc: stable@vger.kernel.org
The enable bit indexes for DCDC4 and DCDC5 regulators are off by 1.
We haven't run into any problems with this since either the regulators
aren't defined in the DT and aren't used, or all the DCDC regulators
have the "always-on" property set, as they are almost always used
for system critical loads.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Implement the ->enable(), ->disable() and ->is_enabled methods and remove
the PWM call in ->set_voltage_sel().
This is particularly important for critical regulators tagged as always-on,
because not claiming the PWM (and its dependencies) might lead to
unpredictable behavior (like a system hang because the PWM clk is only
claimed when the PWM device is enabled).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we are already registering a device with regulator_class for each
regulator device, regulator_list is redundant and can be replaced with
calls to class_find_device() and class_for_each_device().
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree based initialization support for tps65023 regulators.
Therefore add macros for regulator definition setting of_match and
regulators_node members. Add initialization of regulator_desc data
using these macros. Remove old regulator_desc initialization.
Add device tree binding document for tps65023 regulators.
Signed-off-by: Thomas Elste <thomas.elste@imms.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ret pointer passed to regulator_dev_lookup is only filled with a
valid error code if regulator_dev_lookup returned NULL. Currently
regulator_resolve_supply checks this ret value before it checks if a
regulator was returned, this can result in valid regulator lookups being
ignored.
Fixes: 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Introduce "regulator-allow-set-load" property to make it possible to
flag in the board configuration that a regulator is allowed to have the
load requirements changed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The same error print exists 4 times in the regulator core
<rdev>: operation not allowed
Unfortunately, seeing this in the dmesg is not very informative.
Add what type of operation is not allowed to the message so that
these errors are unique, hopefully pointing developers in the
right direction
<rdev>: drms operation not allowed
<rdev>: voltage operation not allowed
<rdev>: current operation not allowed
<rdev>: mode operation not allowed
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing zero to value. This will be needed when range checking
is implemented.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's clearly a typo error that just creates a null statement so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's clearly a typo error that just creates a null statement so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been a busy release for regmap. By far the biggest set of
changes here are those from Markus Pargmann which implement support for
block transfers in smbus devices. This required quite a bit of
refactoring but leaves us better able to handle odd restrictions that
controllers may have and with better performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV6cZyAAoJECTWi3JdVIfQM3sH/RSygzRIOoOuvro0U3qd4+nM
qLzpuZNtuAP7xNc5yJZiixz1S6PqUNl+pK/u58s6x10GWDGsWZY6E0Lg94lYmfhA
26jqWSzrMHp42x+ZN7btLExzPTVnvRerrjtj4mqz6t4yun9SzqVymaZTUZ1hqPHB
qxSNHs3rHPiqiEWpQKJXb+5dazYYJCbOUrlivxJCk60+ns1N88cA71aY+5/zq5uy
36e0iYe3s+lv0lptedarFCf9p7o1E6EQzhvEMfyquGXtvq8fl7Qdeo7riRFQ8Iiy
sygCb3AYuZIiqnOC7+90xkr2Oq0iwdJUD91A9sl/SRiwgItG9jW03bWNHYIhQyk=
=CbGt
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for regmap.
By far the biggest set of changes here are those from Markus Pargmann
which implement support for block transfers in smbus devices. This
required quite a bit of refactoring but leaves us better able to
handle odd restrictions that controllers may have and with better
performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald"
* tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (25 commits)
regmap: fix a NULL pointer dereference in __regmap_init
regmap: Support bulk reads for devices without raw formatting
regmap-i2c: Add smbus i2c block support
regmap: Add raw_write/read checks for max_raw_write/read sizes
regmap: regmap max_raw_read/write getter functions
regmap: Introduce max_raw_read/write for regmap_bulk_read/write
regmap: Add missing comments about struct regmap_bus
regmap: No multi_write support if bus->write does not exist
regmap: Split use_single_rw internally into use_single_read/write
regmap: Fix regmap_bulk_write for bus writes
regmap: regmap_raw_read return error on !bus->read
regulator: core: Print at debug level on debugfs creation failure
regmap: Fix regmap_can_raw_write check
regmap: fix typos in regmap.c
regmap: Fix integertypes for register address and value
regmap: Move documentation to regmap.h
regmap: Use different lockdep class for each regmap init call
thermal: sti: Add parentheses around bridge->ops->regmap_init call
mfd: vexpress: Add parentheses around bridge->ops->regmap_init call
regmap: debugfs: Fix misuse of IS_ENABLED
...
Add separate compatible strings for every platform and populate the
pbias register offset in the driver data.
This helps avoid depending on the dt for pbias register offset.
Also update the dt binding documentation for the new compatible
strings.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The smd rpm structures are always in little endian, but this
driver is not capable of being used on big endian CPUs. Annotate
the little endian data members and update the code to do the
proper byte swapping.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were checking rdev->supply for NULL after dereferencing it. Lets
check for rdev->supply along with _regulator_is_enabled() and call
regulator_enable() only if rdev->supply is not NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/mt6311-regulator.c:169:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has a I2C device id table that is used to create the modaliases
and already contains a "ltc3589" device id. So the modalias is unnecessary.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has a I2C device id table that is used to create the modaliases
and also "ad5398-regulator" is not a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has a I2C device id table that is used to create the modaliases
and also "pfuze100-regulator" is not a supported I2C id, so is never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When calling regulator_set_load, regulator_check_drms prints and returns
an error if the regulator device's flag REGULATOR_CHANGE_DRMS isn't set.
drms_uA_update, however, bails out without reporting an error.
Replace the error print with a debug level print so that we don't get
such prints when the underlying regulator doesn't support DRMS.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If memory allocation gets failed on parsing the DT, then it returns error
'-ENOMEM' explicitly. Then, the driver exists from the _probe().
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, lp872x driver parses the DT and copies values into the
'cl->dev.platform_data' if 'of_node' exists.
This may have architectural issue. Platform data is configurable through
the DT or I2C board info inside the platform area.
However, lp872x driver changes this configuration when it is loaded.
The lp872x driver should get data from the platform side and use the private
data, 'lp872x->pdata' instead of changing the original platform data.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: I2C id table or OF match table).
So drivers needs to export the I2C id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and I2C id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same I2C device name for example.
To avoid the above, the I2C core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX77693 based regulators are used by USB gadget subsystem, which
doesn't support deferred probe, so the driver should be registered
before USB gadget drivers get probed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just setting fixed_uV is not enough, the regulator core will also check
n_voltages setting. The fixed_uV only works when n_voltages is 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver for regulators exposed by the Resource Power Manager (RPM) found
in devices based on Qualcomm 8974 and newer platforms.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Andy Gross <agross@codeaurora.org>
Tested-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Failure to create a debugfs node is not an error, but we print a
warning upon failure to create the node. Downgrade this to a
debug printk so that we're quiet here. This allows multiple
drivers to request a CPU's regulator so that CPUfreq and AVSish
drivers can coexist.
The downside of this approach is that whoever gets to debugfs first
the others who come later to not have any debugfs attributes associated
with them.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_disable of pbias always writes '0' to the enable_reg.
However actual disable value of pbias regulator is not always '0'.
Fix it by populating the disable_val in pbias_reg_info for the
various platforms and assign it to the disable_val of
pbias regulator descriptor. This will be used by
regulator_disable_regmap while disabling pbias regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The regulator_list has exactly the same contents as the list that the
driver core maintains of regulator_class members so is redundant. As a
first step in converting over to use the class device list convert our
iteration in late_initcall() to use the class device iterator.
Signed-off-by: Mark Brown <broonie@kernel.org>
We really ought to be using the class dvice lifetime management features
more than we are rather than open coding them so take a step towards that
by moving some of the simplest deallocations to the dev_release() function.
Signed-off-by: Mark Brown <broonie@kernel.org>
When we release a regulator we need to remove references to it from the
rdev which means locking the rdev. Currently we also free resources
associated with the regulator inside the rdev lock but there is no need
to do this, we can reduce the region the lock is held by restricting it
to just actions that affect the rdev.
Signed-off-by: Mark Brown <broonie@kernel.org>
When removing a regulator we hold regulator_list_mutex in order to
ensure the regualtor doesn't become removed again. However we only need
to protect the list until we remove the regulator from the list so move
the unlock earlier to reduce the locked region.
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows the module to be autoloaded.
Together with 07949bf9c6 ("cpufreq: dt: allow driver to boot
automatically") this is sufficient to allow a modular kernel (such
as Debian's) to enable cpufreq on a Cubietruck.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make mt6311_buck_ops, mt6311_ldo_ops and mt6311_regulators const and remove
unneeded error variable in mt6311_i2c_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum voltage of buck should be 1.39375V.
1.39375V = 0.6V + 0.00625V * 127, 127 is the max_sel of linear range.
Reported-by: Axel Lin <axel.lin@ingics.com>
signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regmap helpers for get_voltage_sel and set_voltage_sel ops
if the DVS GPIO is not set.
The DVS GPIO allows on the fly selection of the VSEL register
from two choices. However, if it is not set, the VSEL register
will stay fixed and we can use the regmap ops. This allows use
of the *hardware_vsel* regulator APIs.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for over current protection (OCP), pin control
selection, soft start strength, and auto-mode.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can automatically shut down when they detect an
over current event. Add an op (set_over_current_protection) and a
DT property + constraint to support this capability.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator support for mt6311.
It has 2 regulaotrs - Buck and LDO, provide the related buck/ldo voltage
data to the driver, and creates the regulator_desc table. Supported
operations for Buck are enabled/disabled and voltage change, only
enabled/disabled for LDO.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_regulator_match.driver_data is (void *). tps6586x uses it to store an
anonymous enum value (those TPS6586X_ID_ values).
Later, it tries to extract the ID by casting directly to an int, which is a
no-no ([-Wpointer-to-int-cast]):
drivers/regulator/tps6586x-regulator.c: In function 'tps6586x_parse_regulator_dt':
drivers/regulator/tps6586x-regulator.c:430:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
id = (int)tps6586x_matches[i].driver_data;
^
Instead of casting to int, uintptr_t is better suited for receiving and
comparing integers extracted from void *. This is especially true on
64-bit systems where sizeof(void *) != sizeof(int).
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod functions include variants for managed gpiod resources. Use it
to simplify the remove function.
As the driver handles a device node without a specification of dvs gpios
just fine, additionally use the variant of gpiod_get exactly for this
use case. This makes error checking more strict.
As a third benefit this patch makes the driver use the flags parameter
of gpiod_get* which will not be optional any more after 4.2 and so
prevents a build failure when the respective gpiod commit is merged.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a build problem on mips found by the kbuild test robot:
drivers/regulator/rk808-regulator.c: In function 'rk808_buck1_2_get_voltage_sel_regmap':
drivers/regulator/rk808-regulator.c:97:2: error: implicit declaration of function 'gpiod_get_value' [-Werror=implicit-function-declaration]
if (IS_ERR(gpio) || gpiod_get_value(gpio) == 0)
^
Fixes: bad47ad2ee ("regulator: rk808: fixed the overshoot when adjust voltage")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a overshoot in DCDC1/DCDC2, we have 2 method to workaround:
1st is use dvs pin to switch the voltage between value in BUCKn_ON_VSEL
and BUCKn_DVS_VSEL. If DVS pin is inactive, the voltage of DCDC1/DCDC2
are controlled by BUCKn_ON_VSEL, when we pull dvs1/dvs2 pin to active,
they would be controlled by BUCKn_DVS_VSEL. In this case, the ramp rate
is same as the value programmed in BUCKn_RATE, and the fastest rate is
10mv/us.
2nd method is gradual adjustment, adjust the voltage to a target value
step by step via i2c, each step is set to 100 mA. If you write the
voltage directly using an i2c write the rk808 will always ramp as fast
as it possibly can, about 100mv/us.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max77693 regulator driver supports Maxim 77843 device so remove the
max77843 driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The charger and safeout parts of MAX77843 are almost the same as MAX77693.
From regulator point of view the only differences are the constraints
and register values related to these constraints. Now the max77693
regulator driver can be used for MAX77843 device.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the same definition of state container as in MAX77693 drivers.
This will allow usage of one regulator driver in both devices: MAX77693
and MAX77843.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for different configurations of charger's registers so the
same driver could be used on other devices (e.g. MAX77843).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_resolve_supply() function calls set_supply() which in turn
calls create_regulator() to allocate a supply regulator.
If an error occurs after set_supply() succeeded, the allocated regulator
has to be freed before propagating the error code.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator is unregistered with regulator_unregister(), a call to
regulator_put() is made for its input supply if there is one. This does
a module_put() to decrement the refcount of the module that owns the
supply but there isn't a corresponding try_module_get() in set_supply()
to make the calls balanced.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is add regulator_nodes/of_match in the regulator
descriptor for using information from DT instead of specific codes.
With this patch, driver gets simplified,
- No need to maintain "struct of_regulator_match" table
and call of_regulator_match() fn.
- No need for pm800_regulator_dt_init() fn, as it was only
used for of_regulator_match().
- probe() fn got simplified around regulator_config and regulator_desc
initialization.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces standard regulator_register with
devm_regulator_register() fn, as using devm_regulator_register() fn
simplifies the driver return/exit path.
As part of this update, patch also cleanups up all unnecessary changes
which is result of this patch -
- Remove _remove() fn, as devm_ variant takes care of it.
- Remove pm800_regulators.regulators[] field, as it was only
needed during cleanup, so we no longer need this.
This also saved some amount of memory.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch makes code more clean from readability point of view,
make all assignments of LDO, BUCk and regulator_ops structure
at the same indentation.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When resolving device supplies if we fail to look up the regulator we
substitute in the dummy supply instead if the system has fully specified
constraints. When resolving supplies for regulators we do not have the
equivalent code and instead just directly use the regulator_dev_lookup()
result causing spurious failures.
This does not affect DT systems since we are able to detect missing
mappings directly as part of regulator_dev_lookup() and so have appropriate
handling in the DT specific code.
Reported-by: Christian Hartmann <cornogle@googlemail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for supporting da9215 buck converter.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add optional interrupt support to the da9210 regulator driver, to handle
over-current, under- and over-voltage, and over-temperature events.
Only the interrupt sources for which we handle events are unmasked, to
avoid interrupts we cannot handle.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/pwm-regulator.c:
In function ‘pwm_regulator_init_table’:
drivers/regulator/pwm-regulator.c:171:14:
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/pwm-regulator.c:
In function 'pwm_regulator_init_table':
drivers/regulator/pwm-regulator.c:172:14:
warning: 'length' is used uninitialized in this function [-Wuninitialized]
if ((length < sizeof(*duty_cycle_table)) ||
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/pwm-regulator.c:
In function 'pwm_regulator_init_continuous':
drivers/regulator/pwm-regulator.c:202:22:
warning: unused variable 'np' [-Wunused-variable]
struct device_node *np = pdev->dev.of_node;
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per datasheet,
Except LDO2, all other LDO's use bit [3:0] for VOUT select.
Current code uses wrong mask value of 0x1f, So this patch
fixes it to use 0xf.
Signed-off-by: Yi Zhang <yizhang@marvell.com>
[vaibhav.hiremath@linaro.org: Updated changelog with more detailed description]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove over-bracketing, use framework API to fetch PWM period and
be more forthcoming that pwm_voltage_to_duty_cycle() actually returns
duty cycle as a percentage, rather than a register value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In "[3d7ef30] regulator: pwm-regulator: Simplify voltage to duty-cycle
call" we stopped using max_duty_cycle, so we can retire it from device
data and DT.
There is no need to deprecate this property, as it hasn't hit Mainline
yet.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Perhaps this is just personal preference, but ...
This patch introduces a new local variable to receive and test regulator
initialisation data. It simplifies and cleans up the code making it
that little bit easier to read and maintain. The local value is assigned
to the structure attribute when all the others are. This is the way we
usually do things.
Prevents this kind of nonsense:
this->is->just.silly = fetch_silly_value(&pointer);
if (!this->is->just.silly) {
printk("Silly value failed: %d\n", this->is->just.silly);
return this->is->just.silly;
}
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we reverse some of the logic and change the formula used,
we can simplify the function greatly.
It is intentional that this function is supplied and then re-worked
within the same patch-set. The submission in the previous patch is
the tried and tested (i.e. in real releases) method written by ST.
This patch contains a simplification provided later. It looks and
performs better, but doesn't have the same time-under-test that the
original method does. The idea is that we keep some history in
order to provide an easy way back i.e. revert.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current version of PWM regulator only supports a static table
approach, where pre-calculated values are supplied by the vendor and
obtained via DT. The continuous-voltage method takes min_uV and
max_uV, and divides the difference between them up into a number of
slices. The number of slices depend on how large the duty cycle
register is. This information is provided by a DT property.
As the name alludes, this provides values for a continuous voltage
range between min_uV and max_uV, which has obvious benefits over
either limited voltage possibilities, or the requirement to provide
a large voltage-table.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to configure Enhanced Transient Response Enable (ETR)
and Sensitivity Selection based on maximum current i.e. expected
load on that rail.
Maxim recommended as:
- Enable ETR with high sensitivity (75mV/us) for 0 to 9A expected loads,
- Enable ETR with low sensitivity (150mV/us) for 9A to 12A expected loads.
- Disable ETR for expected load > 12A.
These recommendation will be configured for MAX77621 when maximum load
is provided through regulator constraint for maximum current from platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MAX8973/MAX77621 feature an Enhanced Transient Response(ETR)
circuit that is enabled through software. The enhanced transient
response reduces the voltage droop during large load steps by
temporarily allowing all three phases to fire in unison, slewing
total inductor current faster than would normally be possible if
all three phases continued to operate 120deg out of phase. The
enhanced transient response detector features two selectable
sensitivity settings, which select the output voltage slew rate
during load transients that triggers the ETR circuit. The sensitivity
of the ETR detector is set by the CKADV[1:0] bits in the CONTROL2
register.
Add support to configure the ETR through platform data from DT.
Update the DT binding document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control flag for the bias control is MAX8973_CONTROL_BIAS_ENABLE
rather than MAX8973_BIAS_ENABLE which is macro for the bits in
register.
Fix this typo.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Take this out of the main .probe() routine in order to facilitate the
introduction of different ways to obtain 'duty cycle' information.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ltc3589_reg_defaults[] is not modified after initialized, so make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add lockdep_assert_held_once() to functions explicitly mentioning that
rdev or regulator_list mutex must be held. Using WARN_ONCE shouldn't
pollute the dmesg to much.
The patch (if CONFIG_LOCKDEP enabled) will show warnings in certain
regulators calling regulator_notifier_call_chain() without rdev->mutex
held.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qotW
-----END PGP SIGNATURE-----
Merge tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull implicit module.h fixes from Paul Gortmaker:
"Fix up implicit <module.h> users that will break later.
The files changed here are simply modular source files that are
implicitly relying on <module.h> being present. We fix them up now,
so that we can decouple some of the module related init code from the
core init code in the future.
The addition of the module.h include to several files here is also a
no-op from a code generation point of view, else there would already
be compile issues with these files today.
There may be lots more implicit includes of <module.h> in tree, but
these are the ones that extensive build test coverage has shown that
must be fixed in order to avoid build breakage fallout for the pending
module.h <---> init.h code relocation we desire to complete"
* tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
frv: add module.h to mb93090-mb00/flash.c to avoid compile fail
drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code
drivers/staging: include <module.h> for modular android tegra_ion code
crypto/asymmetric_keys: pkcs7_key_type needs module.h
sh: mach-highlander/psw.c is tristate and should use module.h
drivers/regulator: include <module.h> for modular max77802 code
drivers/pcmcia: include <module.h> for modular xxs1500_ss code
drivers/hsi: include <module.h> for modular omap_ssi code
drivers/gpu: include <module.h> for modular rockchip code
drivers/gpio: include <module.h> for modular crystalcove code
drivers/clk: include <module.h> for clk-max77xxx modular code
It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
* ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
* HD-audio
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
* ASoC
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
* Firewire
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
* Misc
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=D78E
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
HD-audio:
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
ASoC:
- Support for loading ASoC topology maps from firmware, intended to
be used to allow self-describing DSP firmware images to be built
which can map controls added by the DSP to userspace without the
kernel needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP
driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
Firewire:
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
Misc:
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup"
* tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (533 commits)
ALSA: pcm: Fix pcm_class sysfs output
ALSA: hda-beep: Update authors dead email address
ASoC: wm_adsp: Move DSP Rate controls into the codec
ASoC: wm8995: Fix setting sysclk for WM8995_SYSCLK_MCLK2 case
ALSA: hda: provide default bus io ops extended hdac
ALSA: hda: add hda link cleanup routine
ALSA: hda: add hdac_ext stream creation and cleanup routines
ASoC: rsrc-card: remove unused ret
ALSA: HDAC: move SND_HDA_PREALLOC_SIZE to core
ASoC: mediatek: Add machine driver for rt5650 rt5676 codec
ASoC: mediatek: Add machine driver for MAX98090 codec
ASoC: mediatek: Add AFE platform driver
ASoC: rsnd: remove io from rsnd_mod
ASoC: rsnd: move rsnd_mod_is_working() to rsnd_io_is_working()
ASoC: rsnd: don't use rsnd_mod_to_io() on snd_kcontrol
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_src_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_ssi_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_dma_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_get_adinr()
ASoC: rsnd: add common interrupt handler for SSI/SRC/DMA
...
Status of enabling suspend mode for regulator was stored in bitmap-like
long integer.
However since adding support for S2MPU02 the number of regulators
exceeded 32 so on devices with more than 32 regulators (S2MPU02 and
S2MPS13) overflow happens when shifting the bit. This could lead to
enabling suspend mode for completely different regulator than intended
or to switching different regulator to other mode (e.g. from always
enabled to controlled by PWRHOLD pin). Both cases could result in larger
energy usage and issues when suspending to RAM.
Fixes: 00e2573d2c ("regulator: s2mps11: Add support S2MPU02 regulator device")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
n /= range->step_uV + 1; is equivalent to n /= (range->step_uV + 1);
which is wrong. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/qcom_spmi-regulator.c:751:3-50: code aligned
with following code on line 753
drivers/regulator/qcom_spmi-regulator.c:584:3-41: code aligned
with following code on line 587
These lines where missing braces causing the break to always
be executed even when it shouldn't be. Fix it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This file is built off of a tristate Kconfig option and also contains
modular function calls so it should explicitly include module.h to
avoid compile breakage during header shuffles done in the future.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Simplify a trivial if-return sequence and combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
PM8916 PMICs. This driver is based largely on code from
codeaurora.org[1].
[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/qpnp-regulator.c?h=msm-3.10
Cc: David Collins <collinsd@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix trivial typo.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to avoid potential overflows in print_constraints we
better replace sprintf() with scnprintf().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
We weren't taking into account the already used buffer when telling
sprintf() where to print to.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim MAX77621 device is high-efficiency, three-phase,
DC-DC step-down switching regulator delivers peak
output currents up to 16A. This device is extension of
MAX8973 and compatible with the register definition.
The MAX77621 has the SHUTDOWN pin which is EN pin on the
MAX8973. On MAX77621, the SHUTDOWN pin (active low) reset
device register to its POR/OTP value. The voltage output
is enabled when SHUTDONW pin is HIGH and EN bit on VOUT
register is HIGH.
For MAX8973, VOUT is enabled when EN bit or EN pin is high.
Add support of the MAX77621 device on max8973 regulator driver
with following changes:
- Make sure SHUTDOWN pin is set HIGH through GPIO calls if
GPIO from AP connected to SHUTDOWN pin provided.
- Enable/disable the rail through register access only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator core framework support the configuration of ramp
delay reading from platform specific regulator data via the
regulator callback ops.
Instead of reading regulator init data on driver and setting
ramp delay, use the callback to achieve this.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Regulator Device keeps a full copy of it's own, which can be easily accessed.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't consider a failure to add the sysfs node as a problem,
so use sysfs_create_link_nowarn() so that we don't print a
backtrace when duplicated files exist. Also, downgrade the printk
message to a debug statement so that we're quiet here. This
allows multiple drivers to request a CPU's regulator so that
CPUfreq and AVSish drivers can coexist.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the driver for the internal regulator to also enable/disable
the codec internal clock frequency controller is an unexpected
side-effect for a regulator, and also means that the core clocks
won't be changed as expected if an external regulator is used to
power the codec.
The DVFS is now handled by the codec driver so can be removed from
the LDO1 driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code does not set regulators->irq_ldo_lim and regulators->irq_uvov,
so it actually calls free_irq(0, regulators) twice in remove() but does not
free the irq actually used.
Convert to use devm_request_threaded_irq instead and then we don't need to
take care the clean up irq so remove irq_ldo_lim and irq_uvov from
struct da9063_regulators. Note, regulators->irq_uvov is not used at all in
current code.
There is a slightly change in this patch, it will return error in probe()
if devm_request_threaded_irq fails. If the irq is optional, it should be
fine to allow platform_get_irq_byname fails. But current code does not
allow platform_get_irq_byname fails. So I think the reason to allow
request irq failure is just because the irq leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unused variable build warning for reg_matches that appears
during the compilation of the DA9062 regulator driver.
da9062-regulator.c: In function da9062_regulator_probe:
da9062-regulator.c:727:29: warning: unused variable reg_matches
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix broken probe of da9052 regulators, which since commit b3f6c73db7
("mfd: da9052-core: Fix platform-device id collision") use a
non-deterministic platform-device id to retrieve static regulator
information. Fortunately, adequate error handling was in place so probe
would simply fail with an error message.
Update the mfd-cell ids to be zero-based and use those to identify the
cells when probing the regulator devices.
Fixes: b3f6c73db7 ("mfd: da9052-core: Fix platform-device id collision")
Cc: stable <stable@vger.kernel.org> # v3.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Setting the set_voltage_time_sel callback to the standard function
regulator_set_voltage_time_sel enables the regulator to actually honor
ramp-delays when during regulator_set_voltage calls.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extra space between platform prefix and driver name in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX8973 supports the voltage output enable/disable through its EN
pin. This EN pin can be connected through GPIO from host processor.
Add support to provide GPIO number from platform/DT and if it is
valid GPIO then enable external control default.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some platform specific parameter required to configure
the device like enable external control, DVS gpio etc.
Add DT parsing of such properties to make platform specific data.
Update DT binding doc accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To find that dvs-gpio is valid or not, gpio API gpio_is_valid()
can be directly used instead of intermediate variable.
Removing the extra variable and using the gpio_is_valid().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If platform data has dvs-gpio value 0 as default/unset then
make this as invalid gpio so that function gpio_is_valid()
can return false on this case.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add BUCK and LDO regulator driver support for DA9062
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code should handle more than 32 bits here because "id"
can be a value up to MAX77686_REGULATORS (currently 34).
Convert the gpio_enabled type to DECLARE_BITMAP and use
test_bit/set_bit.
Fixes: 3307e9025d ("regulator: max77686: Add GPIO control")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add AXP22X regulator definitions and variant id associations.
This introduces a new "switch" type output for one of the regulators.
It is a switchable secondary output of one regulator, with the same
voltage level as the primary output.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Moved variant choosing to multi family support patch]
[wens@csie.org: Add dc-dc work frequency range]
[wens@csie.org: Add "switch" type output regulator DC1SW]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rework the AXP20X_ macros and probe function to support the several chip
families, so that each family can define it's own set of regulators.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Support different DC-DC work frequency ranges]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If a regulator is listed in devicetree, but the node is marked as
"disabled" we should skip parsing the regulator init data and
deny consumers from interacting with the regulator. This
simplifies devicetree maintenance where we can have one dtsi file
with all regulators supported by a PMIC and then select what
regulators are used depending on the board configuration.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the 1.175V mode on the LDO1 regulator on the
wm5110. This is need as part of the low power sleep mode operation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_is_enabled_regmap() to replace max77843_reg_is_enabled().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX77843_CHG_ENABLE is 0x05, so the enable_mask should be
MAX77843_CHG_MASK | MAX77843_CHG_BUCK_MASK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The custom implementation of 'regulator_ops.is_enabled' callback for
charger regulator is exactly the same as regulator_is_enabled_regmap()
with 'enable_val' set.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded semicolons after the switch statement to satisfy
coccicheck.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In MAX8973, BIAS enable control bit is used for changing the startup time
for voltage output. The startup delay is 240us (typ) when the BIASEN
bit is set to 0. The startup delay is reduced to 20us (typ) when the
BIASEN bit is set to 1.
Pass the enable_time through regulator descriptor based on this flag.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace duplicated SAFEOUT regulators initializers in array of struct
'regulator_desc' arrays with macro. Generated object is the same but
SAFEOUT is described only once.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace duplicated initializers in arrays of struct 'regulator_desc'
with macro. Generated object is the same but each type of regulator is
described only once.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function name in kernel-doc for regulator_map_voltage_linear_range()
was wrong.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ivaylo Dimitrov