It always confuses me to see the mixed instruction length code and
interruption code on user space faults, while the message clearly
says it is the interruption code.
So split the value and print both values separately. Also add the ILC
output to the die() message, so thar user and kernel space faults
contain the same information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the new __NR_s390_pci_mmio_write and __NR_s390_pci_mmio_read
system calls to allow user space applications to access device PCI I/O
memory pages on s390x platform.
[ Martin Schwidefsky: some code beautification ]
Signed-off-by: Alexey Ishchuk <aishchuk@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The floating point registers of a process that uses vector instruction are
not store into task->thread.fp_regs anymore but in the upper halves of the
first 16 vector registers.
The ptrace interface for the peeks and pokes to the user area fails to take
this into account. Fix __peek_user[_compat] and __poke_user[_compat]
to use the vector array for the floating pointer register if the process
has one.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Irq 0 is currently unused on s390. Since there is no reason to
do this start counting at the beginning and gain an additional
irq. Also correctly report the smallest usable irq number for
dynamic allocation.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The git commit c719f56092
"perf: Fix and clean up initialization of pmu::event_idx" removed
the PMU event index callback for all architectures but x86,
remove the initialization of the event index as well.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following warnings from the sparse code checker:
arch/s390/kernel/signal.c:374:38: warning: cast removes address space of expression
arch/s390/kernel/signal.c:374:65: warning: incorrect type in initializer (different address spaces)
arch/s390/kernel/signal.c:374:65: expected unsigned short [noderef] [usertype] <asn:1>*svc
arch/s390/kernel/signal.c:374:65: got void *
arch/s390/kernel/compat_signal.c:437:38: warning: cast removes address space of expression
arch/s390/kernel/compat_signal.c:437:65: warning: incorrect type in initializer (different address spaces)
arch/s390/kernel/compat_signal.c:437:65: expected unsigned short [noderef] [usertype] <asn:1>*svc
arch/s390/kernel/compat_signal.c:437:65: got void *
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kernel build for s390 fails for gcc compilers with version 3.x,
set the minimum required version of gcc to version 4.3.
As the atomic builtins are available with all gcc 4.x compilers,
use the __sync_val_compare_and_swap and __sync_bool_compare_and_swap
functions to replace the complex macro and inline assembler magic
in include/asm/cmpxchg.h. The compiler can just-do-it and generates
better code with the builtins.
While we are at it use __sync_bool_compare_and_swap for the
_raw_compare_and_swap function in the spinlock code as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use NOKPROBE_SYMBOL() instead of __kprobes annotation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the function tracer is enabled, allow to set kprobes on the first
instruction of a function (which is the function trace caller):
If no kprobe is set handling of enabling and disabling function tracing
of a function simply patches the first instruction. Either it is a nop
(right now it's an unconditional branch, which skips the mcount block),
or it's a branch to the ftrace_caller() function.
If a kprobe is being placed on a function tracer calling instruction
we encode if we actually have a nop or branch in the remaining bytes
after the breakpoint instruction (illegal opcode).
This is possible, since the size of the instruction used for the nop
and branch is six bytes, while the size of the breakpoint is only
two bytes.
Therefore the first two bytes contain the illegal opcode and the last
four bytes contain either "0" for nop or "1" for branch. The kprobes
code will then execute/simulate the correct instruction.
Instruction patching for kprobes and function tracer is always done
with stop_machine(). Therefore we don't have any races where an
instruction is patched concurrently on a different cpu.
Besides that also the program check handler which executes the function
trace caller instruction won't be executed concurrently to any
stop_machine() execution.
This allows to keep full fault based kprobes handling which generates
correct pt_regs contents automatically.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kernel provided vdso functions do not get a stack frame from the
calling function and therefore may not change the stack contents, unless
they allocate space on their own.
This problem was exposed with 070b7be633 "s390/vdso: replace stck with
stcke" which writes 16 bytes instead of 8 bytes into the stack frame. These
additional 8 bytes however were indeed used by the caller (glibc) to save
data and therefore this data was corrupted by the vdso code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The last high frequency call site of the STCK instruction is
do_account_vtime. Replace it with the faster STCKF instruction.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 updates from Martin Schwidefsky:
"One patch to enable the BPF system call and three more bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix kprobes dependency
s390: wire up bpf syscall
s390/mm: fixing calls of pte_unmap_unlock
s390/hmcdrv: Restrict s390 HMC driver to S390 arch
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
If kprobes is disabled uprobes will not compile.
Fix this by including the correct header files.
Signed-off-by: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Pull s390 updates from Martin Schwidefsky:
"This patch set contains the main portion of the changes for 3.18 in
regard to the s390 architecture. It is a bit bigger than usual,
mainly because of a new driver and the vector extension patches.
The interesting bits are:
- Quite a bit of work on the tracing front. Uprobes is enabled and
the ftrace code is reworked to get some of the lost performance
back if CONFIG_FTRACE is enabled.
- To improve boot time with CONFIG_DEBIG_PAGEALLOC, support for the
IPTE range facility is added.
- The rwlock code is re-factored to improve writer fairness and to be
able to use the interlocked-access instructions.
- The kernel part for the support of the vector extension is added.
- The device driver to access the CD/DVD on the HMC is added, this
will hopefully come in handy to improve the installation process.
- Add support for control-unit initiated reconfiguration.
- The crypto device driver is enhanced to enable the additional AP
domains and to allow the new crypto hardware to be used.
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/ftrace: simplify enabling/disabling of ftrace_graph_caller
s390/ftrace: remove 31 bit ftrace support
s390/kdump: add support for vector extension
s390/disassembler: add vector instructions
s390: add support for vector extension
s390/zcrypt: Toleration of new crypto hardware
s390/idle: consolidate idle functions and definitions
s390/nohz: use a per-cpu flag for arch_needs_cpu
s390/vtime: do not reset idle data on CPU hotplug
s390/dasd: add support for control unit initiated reconfiguration
s390/dasd: fix infinite loop during format
s390/mm: make use of ipte range facility
s390/setup: correct 4-level kernel page table detection
s390/topology: call set_sched_topology early
s390/uprobes: architecture backend for uprobes
s390/uprobes: common library for kprobes and uprobes
s390/rwlock: use the interlocked-access facility 1 instructions
s390/rwlock: improve writer fairness
s390/rwlock: remove interrupt-enabling rwlock variant.
s390/mm: remove change bit override support
...
Pull x86 seccomp changes from Ingo Molnar:
"This tree includes x86 seccomp filter speedups and related preparatory
work, which touches core seccomp facilities as well.
The main idea is to split seccomp into two phases, to be able to enter
a simple fast path for syscalls with ptrace side effects.
There's no substantial user-visible (and ABI) effects expected from
this, except a change in how we emit a better audit record for
SECCOMP_RET_TRACE events"
* 'x86-seccomp-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64, entry: Use split-phase syscall_trace_enter for 64-bit syscalls
x86_64, entry: Treat regs->ax the same in fastpath and slowpath syscalls
x86: Split syscall_trace_enter into two phases
x86, entry: Only call user_exit if TIF_NOHZ
x86, x32, audit: Fix x32's AUDIT_ARCH wrt audit
seccomp: Document two-phase seccomp and arch-provided seccomp_data
seccomp: Allow arch code to provide seccomp_data
seccomp: Refactor the filter callback and the API
seccomp,x86,arm,mips,s390: Remove nr parameter from secure_computing
The different architectures used their own (and different) declarations:
extern __visible const void __nosave_begin, __nosave_end;
extern const void __nosave_begin, __nosave_end;
extern long __nosave_begin, __nosave_end;
Consolidate them using the first variant in <asm/sections.h>.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can simply patch the mask field within the branch relative on
condition instruction at the beginning of the ftrace_graph_caller
code block.
This makes the logic even simpler and we get rid of the displacement
calculation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
31 bit and 64 bit diverge more and more and it is rather painful
to keep both parts running.
To make things simpler just remove the 31 bit support which nobody
uses anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With this patch for kdump the s390 vector registers are stored into the
prepared save areas in the old kernel and into the REGSET_VX_LOW and
REGSET_VX_HIGH ELF notes for /proc/vmcore in the new kernel.
The NT_S390_VXRS_LOW note contains the lower halves of the first 16 vector
registers 0-15. The higher halves are stored in the floating point register
ELF note. The NT_S390_VXRS_HIGH contains the full vector registers 16-31.
The kernel provides a save area for storing vector register in case of
machine checks. A pointer to this save are is stored in the CPU lowcore
at offset 0x11b0. This save area is also used to save the registers for
kdump. In case of a dumped crashed kdump those areas are used to extract
the registers of the production system.
The vector registers for remote CPUs are stored using the "store additional
status at address" SIGP. For the dump CPU the vector registers are stored
with the VSTM instruction.
With this patch also zfcpdump stores the vector registers.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vector extension introduces 32 128-bit vector registers and a set of
instruction to operate on the vector registers.
The kernel can control the use of vector registers for the problem state
program with a bit in control register 0. Once enabled for a process the
kernel needs to retain the content of the vector registers on context
switch. The signal frame is extended to include the vector registers.
Two new register sets NT_S390_VXRS_LOW and NT_S390_VXRS_HIGH are added
to the regset interface for the debugger and core dumps.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the C functions and definitions related to the idle state handling
to arch/s390/include/asm/idle.h and arch/s390/kernel/idle.c. The function
s390_get_idle_time is renamed to arch_cpu_idle_time and vtime_stop_cpu to
enabled_wait.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the nohz_delay bit from the s390_idle data structure to the
per-cpu flags. Clear the nohz delay flag in __cpu_disable and
remove the cpu hotplug notifier that used to do this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sysfs attributes /sys/devices/system/cpu/cpu0/idle_count and
/sys/devices/system/cpu/cpu0/idle_time_us are reset to zero every
time a CPU is set online. The idle and iowait fields in /proc/stat
corresponding to idle_time_us are not reset. To make things
consistent do not reset the data for the sys attributes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix calculation to decide if a 4-level kernel page table is required.
Git commit c972cc60c2 "s390/vmalloc: have separate modules area"
added the separate module area which reduces the size of the vmalloc
area but fails to take it into account for the 3 vs 4 level page table
decision.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The call to topology_init is too late for the set_sched_topology call.
The initial scheduling domain structure has already been established
with default topology array. Use the smp_cpus_done() call to get the
s390 specific topology array registered early enough.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch moves common functions from kprobes.c to probes.c.
Thus its possible for uprobes to use them without enabling kprobes.
Signed-off-by: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The architecture suggests to use address 0 as parameter for stfl,
to allow for future extensions. Using __LC_STFL_FAC_LIST (0x200)
shows which address is used, but might be not future proof.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add an owner field to the arch_rwlock_t to be able to pass the timeslice
of a virtual CPU with diagnose 0x9c to the lock owner in case the rwlock
is write-locked. The undirected yield in case the rwlock is acquired
writable but the lock is read-locked is removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This device driver allows accessing a HMC drive CD/DVD-ROM.
It can be used in a LPAR and z/VM environment.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ralf Hoppe <rhoppe@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce the number of executed instructions within the mcount block if
function tracing is enabled. We achieve that by using a non-standard
C function call ABI. Since the called function is also written in
assembler this is not a problem.
This also allows to replace the unconditional store at the beginning
of the mcount block with a larl instruction, which doesn't touch
memory.
In theory we could also patch the first instruction of the mcount block
to enable and disable function tracing. However this would break kprobes.
This could be fixed with implementing the "kprobes_on_ftrace" feature;
however keeping the odd jprobes working seems not to be possible without
a lot of code churn. Therefore keep the code easy and simply accept one
wasted 1-cycle "larl" instruction per function prologue.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Even if it has a __used annotation it is actually unused.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We have too many combinations for function tracing. Lets simply stick to
the most advanced option, so we don't have to care of other combinations.
This means we always select DYNAMIC_FTRACE if FUNCTION_TRACER is selected.
In the s390 Makefile also remove CONFIG_FTRACE_SYSCALLS since that
functionality got moved to architecture independent code in the meantime.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This code is based on a patch from Vojtech Pavlik.
http://marc.info/?l=linux-s390&m=140438885114413&w=2
The actual implementation now differs significantly:
Instead of adding a second function "ftrace_regs_caller" which would be nearly
identical to the existing ftrace_caller function, the current ftrace_caller
function is now an alias to ftrace_regs_caller and always passes the needed
pt_regs structure and function_trace_op parameters unconditionally.
Besides that also use asm offsets to correctly allocate and access the new
struct pt_regs on the stack.
While at it we can make use of new instruction to get rid of some indirect
loads if compiled for new machines.
The passed struct pt_regs can be changed by the called function and it's new
contents will replace the current contents.
Note: to change the return address the embedded psw member of the pt_regs
structure must be changed. The psw member is right now incomplete, since
the mask part is missing. For all current use cases this should be sufficent.
Providing and restoring a sane mask would mean we need to add an epsw/lpswe
pair to the mcount code. Only these two instruction would cost us ~120 cycles
which currently seems not necessary.
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the function graph tracer is disabled we can skip three additional
instructions. So let's just do this.
So if function tracing is enabled but function graph tracing is
runtime disabled, we get away with a single unconditional branch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add CLOCK_REALTIME_COARSE and CLOCK_MONOTONIC_COARSE optimization to
the 64-bit and 31-bit vdso.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If gettimeofday / clock_gettime are called multiple times in a row
the STCK instruction will stall until a difference in the result is
visible. This unnecessarily slows down the vdso calls, use stcke
instead of stck to get rid of the stall.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The secure_computing function took a syscall number parameter, but
it only paid any attention to that parameter if seccomp mode 1 was
enabled. Rather than coming up with a kludge to get the parameter
to work in mode 2, just remove the parameter.
To avoid churn in arches that don't have seccomp filters (and may
not even support syscall_get_nr right now), this leaves the
parameter in secure_computing_strict, which is now a real function.
For ARM, this is a bit ugly due to the fact that ARM conditionally
supports seccomp filters. Fixing that would probably only be a
couple of lines of code, but it should be coordinated with the audit
maintainers.
This will be a slight slowdown on some arches. The right fix is to
pass in all of seccomp_data instead of trying to make just the
syscall nr part be fast.
This is a prerequisite for making two-phase seccomp work cleanly.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: x86@kernel.org
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
The explicit NULL pointer check on the timespec argument is only
required for clock_getres but not for clock_gettime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the loadparm is only supported for CCW IPL. But also for SCSI
IPL it can be specified either on the HMC load panel respectively
z/VM console or via diagnose 308.
So fix this for SCSI and add the required sysfs attributes for reading the
IPL loadparm and for setting the loadparm for re-IPL.
With this patch the following two sysfs attributes are introduced:
- /sys/firmware/ipl/loadparm (for system that have been IPLed from SCSI)
- /sys/firmware/reipl/fcp/loadparm
Because the loadparm is now available for SCSI and CCW it is moved
now from "struct ipl_block_ccw" to the generic "struct ipl_list_hdr".
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
this_cpu_inc(y)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: linux390@de.ibm.com
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The virtual-machine cpu information data block and the cpu-id of
the boot cpu can be used as source of device randomness.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For CCW and SCSI IPL the hardware sets the subchannel ID and number
correctly at 0xb8. For kdump at 0xb8 normally there is the data of
the previously IPLed system.
In order to be clean now for kdump and kexec always set the subchannel
ID and number to zero. This tells the next OS that no CCW/SCSI IPL
has been done.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens