At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yuval Mintz says:
====================
qed*: Fixes series
This series contains several small fixes to driver behavior
[4th patch is the only one containing a 'fatal' fix, but the error
is only theoretical for qede; if would require another protocol
driver yet unsubmitted to reach it].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'MODULE_FIBER' value replaced several other FIBER values
in newer management firmware images, so existing code would
fail to properly reflect its mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has 2 sets of entries for handling ramrod configurations
toward firmware - a regular pre-allocated set of entires and a
possible 'unlimited' list of additional pending entries.
In most scenarios the 'unlimited' list would not be used, but
when it does the handling of the ramrod completion doesn't
properly handle the release of the entry.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several user APIs can cause driver to perform an inner-reload.
Currently, doing this would cause the HW/FW statistics of the
adapter to reset, which isn't the expected behavior [statistics
should only reset on explicit unloads].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal loopback in driver is based on two things - first
is the willingness of transmitter to use it [in case of VFs,
this can be forced based on VEPA/VEB] and secondly on another
vport classification configuration which should match the
packet's destination.
Current code allows non-linux VFs to configure a 'promisc'
mode on Tx, meaning all traffic sent by VF would be loopbacked
internally by firmware; This isn't considered a valid mode and
as such should be prevented by PF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no vlan filter is configured, firmware has a configurable
default on whether to pass only untagged packets or all packets
regardless of their tagging. Driver currently doesn't set this
field in the necessary ramrod, causing the default to always be
'receive all'.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style issues in the following files:
ib_cm.c: add space
loop.c: convert spaces to tabs
sysctl.c: add space
tcp.h: convert spaces to tabs
tcp_connect.c:remove extra indentation in switch statement
tcp_recv.c: convert spaces to tabs
tcp_send.c: convert spaces to tabs
transport.c: move brace up one line on for statement
Signed-off-by: Joshua Houghton <josh@awful.name>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A socket connection made in ax.25 is not closed when session is
completed. The heartbeat timer is stopped prematurely and this is
where the socket gets closed. Allow heatbeat timer to run to close
socket. Symptom occurs in kernels >= 4.2.0
Originally sent 6/15/2016. Resend with distribution list matching
scripts/maintainer.pl output.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state of the rds_connection after rds_tcp_reset_callbacks() would
be RDS_CONN_RESETTING and this is the value that should be passed
by rds_tcp_accept_one() to rds_connect_path_complete() to transition
the socket to RDS_CONN_UP.
Fixes: b5c21c0947c1 ("RDS: TCP: fix race windows in send-path quiescence
by rds_tcp_accept_one()")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion to the 64-bit time based ptp methods left two instances
of 'struct timespec' in place. This is harmless because 64-bit
architectures define timespec64 as timespec, and this driver is
not used on 32-bit machines.
However, using 'struct timespec64' directly is obviously the right
thing to do, and will help us remove 'struct timespec' in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b9acf24f77 ("ptp: tilegx: convert to the 64 bit get/set time methods.")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of slowpath tx stats fixes for Spectrum and SwitchX-2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.
Fixes: e577516b9d ("mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We sometimes observe a 'deadly embrace' type deadlock occurring
between mutually connected sockets on the same node. This happens
when the one-hour peer supervision timers happen to expire
simultaneously in both sockets.
The scenario is as follows:
CPU 1: CPU 2:
-------- --------
tipc_sk_timeout(sk1) tipc_sk_timeout(sk2)
lock(sk1.slock) lock(sk2.slock)
msg_create(probe) msg_create(probe)
unlock(sk1.slock) unlock(sk2.slock)
tipc_node_xmit_skb() tipc_node_xmit_skb()
tipc_node_xmit() tipc_node_xmit()
tipc_sk_rcv(sk2) tipc_sk_rcv(sk1)
lock(sk2.slock) lock((sk1.slock)
filter_rcv() filter_rcv()
tipc_sk_proto_rcv() tipc_sk_proto_rcv()
msg_create(probe_rsp) msg_create(probe_rsp)
tipc_sk_respond() tipc_sk_respond()
tipc_node_xmit_skb() tipc_node_xmit_skb()
tipc_node_xmit() tipc_node_xmit()
tipc_sk_rcv(sk1) tipc_sk_rcv(sk2)
lock((sk1.slock) lock((sk2.slock)
===> DEADLOCK ===> DEADLOCK
Further analysis reveals that there are three different locations in the
socket code where tipc_sk_respond() is called within the context of the
socket lock, with ensuing risk of similar deadlocks.
We now solve this by passing a buffer queue along with all upcalls where
sk_lock.slock may potentially be held. Response or rejected message
buffers are accumulated into this queue instead of being sent out
directly, and only sent once we know we are safely outside the slock
context.
Reported-by: GUNA <gbalasun@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are rather small patches but fixing several outstanding bugs in
nf_conntrack and nf_tables, as well as minor problems with missing
SYNPROXY header uapi installation:
1) Oneliner not to leak conntrack kmemcache on module removal, this
problem was introduced in the previous merge window, patch from
Florian Westphal.
2) Two fixes for insufficient ruleset loop validation, one due to
incorrect flag check in nf_tables_bind_set() and another related to
silly wrong generation mask logic from the walk path, from Liping
Zhang.
3) Fix double-free of anonymous sets on error, this fix simplifies the
code to let the abort path take care of releasing the set object,
also from Liping Zhang.
4) The introduction of helper function for transactions broke the skip
inactive rules logic from the nft_do_chain(), again from Liping
Zhang.
5) Two patches to install uapi xt_SYNPROXY.h header and calm down
kbuild robot due to missing #include <linux/types.h>.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
./usr/include/linux/netfilter/xt_SYNPROXY.h:11: found __[us]{8,16,32,64} type without #include <linux/types.h>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Matt Whitlock says:
Without this line, the file xt_SYNPROXY.h does not get installed in
/usr/include/linux/netfilter/, and thus user-space programs cannot make
use of it.
Reported-by: Matt Whitlock <kernel@mattwhitlock.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We were using an incorrect define to get the irq vector number.
NFP_NET_CFG_LSC is a control BAR offset, LSC interrupt vector
index is called NFP_NET_IRQ_LSC_IDX. For machines with less
than 30 CPUs this meant that we were disabling/enabling IRQ 0.
For bigger hosts we were just playing with the 31st RX/TX
interrupt.
Fixes: 0ba40af963 ("nfp: move link state interrupt request/free calls")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 32b8a8e59c ("sit: add IPv4 over IPv4 support")
ipip6_err() may be called for packets whose IP protocol is
IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6.
In the case of IPPROTO_IPIP packets the correct protocol value is not
passed to ipv4_update_pmtu() or ipv4_redirect().
This patch resolves this problem by using the IP protocol of the packet
rather than a hard-coded value. This appears to be consistent
with the usage of the protocol of a packet by icmp_socket_deliver()
the caller of ipip6_err().
I was able to exercise the redirect case by using a setup where an ICMP
redirect was received for the destination of the encapsulated packet.
However, it appears that although incorrect the protocol field is not used
in this case and thus no problem manifests. On inspection it does not
appear that a problem will manifest in the fragmentation needed/update pmtu
case either.
In short I believe this is a cosmetic fix. None the less, the use of
IPPROTO_IPV6 seems wrong and confusing.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4e driver does not support more than one port for VXLAN offload. As
such expecting the hardware to offload other ports is invalid since it
appears the parsing logic is used to perform Tx checksum and segmentation
offloads. Use the vxlan_port number to determine in which cases we can
apply the offload and in which cases we can not.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wextra, we get a harmless warning from the
EFX_EXTRACT_OWORD32 macro:
ethernet/sfc/farch.c: In function 'efx_farch_test_registers':
ethernet/sfc/farch.c:119:30: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:144: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:392: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:731: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
The macro and the caller are both correct, but we can avoid the
warning by changing the index variable to a signed type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: fix known issues
These patches fix some known issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size should be
(agg_buf_sz - packet size) / 8
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the BMU to clear the rx/tx fifo. This avoids that the unexpected
data remains in the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable MAC clock speed down. It may casue the first control
transfer to contain the wrong data, when the power state change
from U1 to U0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
bpf fixes
Fixes for two bpf bugs:
1st bug reported by Sasha Goldshtein here:
https://github.com/iovisor/bcc/issues/570
2nd discovered by Daniel Borkmann by manual code analysis.
See patches for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
similar to bpf_perf_event_output() the bpf_perf_event_read() helper
needs to check the type of the perf_event before reading the counter.
Fixes: a43eec3042 ("bpf: introduce bpf_perf_event_output() helper")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ctx structure passed into bpf programs is different depending on bpf
program type. The verifier incorrectly marked ctx->data and ctx->data_end
access based on ctx offset only. That caused loads in tracing programs
int bpf_prog(struct pt_regs *ctx) { .. ctx->ax .. }
to be incorrectly marked as PTR_TO_PACKET which later caused verifier
to reject the program that was actually valid in tracing context.
Fix this by doing program type specific matching of ctx offsets.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Reported-by: Sasha Goldshtein <goldshtn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) gre_parse_header() can be called from gre_err()
At this point transport header points to ICMP header, not the inner
header.
2) We can not really change transport header as ipgre_err() will later
assume transport header still points to ICMP header (using icmp_hdr())
3) pskb_may_pull() logic in gre_parse_header() really works
if we are interested at zone pointed by skb->data
4) As Jiri explained in commit b7f8fe251e ("gre: do not pull header in
ICMP error processing") we should not pull headers in error handler.
So this fix :
A) changes gre_parse_header() to use skb->data instead of
skb_transport_header()
B) Adds a nhs parameter to gre_parse_header() so that we can skip the
not pulled IP header from error path.
This offset is 0 for normal receive path.
C) remove obsolete IPV6 includes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of net_dbg_ratelimited in the CONFIG_DYNAMIC_DEBUG
case was added with 2c94b5373 ("net: Implement net_dbg_ratelimited() for
CONFIG_DYNAMIC_DEBUG case"). The implementation strategy was to take the
usual definition of the dynamic_pr_debug macro, but alter it by adding a
call to "net_ratelimit()" in the if statement. This is, in fact, the
correct approach.
However, while doing this, the author of the commit forgot to surround
fmt by pr_fmt, resulting in unprefixed log messages appearing in the
console. So, this commit adds back the pr_fmt(fmt) invocation, making
net_dbg_ratelimited properly consistent across DEBUG, no DEBUG, and
DYNAMIC_DEBUG cases, and bringing parity with the behavior of
dynamic_pr_debug as well.
Fixes: 2c94b5373 ("net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Tim Bingham <tbingham@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skfp driver has been moved to drivers/net/fddi/skfp a long time
ago, but we still attempt to include headers from the old location,
which causes a warning when building with W=1:
cc1: error: /git/arm-soc/drivers/net/skfp: No such file or directory [-Werror=missing-include-dirs]
cc1: error: drivers/net/skfp: No such file or directory [-Werror=missing-include-dirs]
Clearly this include directive is not needed any more, so we can
just remove it now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/tipc/link.c: In function ‘tipc_link_timeout’:
net/tipc/link.c:744:28: warning: ‘mtyp’ may be used uninitialized in this function [-Wuninitialized]
Fixes: 42b18f605f ("tipc: refactor function tipc_link_timeout()")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca says:
====================
macsec fixes
Patch 1 adds rcu_barrier() during module unload to prevent possible
panics.
Patch 2 allocates memory for scattergather lists and the IV on the
heap, since they can escape the current function's context during
crypto callbacks.
Patch 3 fixes a failure to create secure associations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASYNC flag prevents initialization on some physical machines.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the crypto callbacks to work properly, we cannot have sg and iv on
the stack. Use kmalloc instead, with a single allocation for
aead_request + scatterlist + iv.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, the various uses of call_rcu could cause a kernel panic.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
saw a debug splat:
net/include/net/sch_generic.h:287 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by kworker/2:1/710:
#0: ("events"){.+.+.+}, at: [<ffffffff8106ca1d>]
#1: ((&q->work)){+.+...}, at: [<ffffffff8106ca1d>] process_one_work+0x14d/0x690
Workqueue: events htb_work_func
Call Trace:
[<ffffffff812dc763>] dump_stack+0x85/0xc2
[<ffffffff8109fee7>] lockdep_rcu_suspicious+0xe7/0x120
[<ffffffff814ced47>] htb_work_func+0x67/0x70
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refers to commands to direct action access as follows:
sudo tc actions add action drop index 12
sudo tc actions add action pipe index 10
And then dumping them like so:
sudo tc actions ls action gact
iproute2 worked because it depended on absence of TCA_ACT_TAB TLV
as end of message.
This fix has been tested with iproute2 and is backward compatible.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And avoid calling tcf_hash_check() twice.
Fixes: a57f19d30b ("net sched: ipt action fix late binding")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now prio_init() can return -ENOMEM, it also has to make sure
any allocated qdiscs are freed, since the caller (qdisc_create()) wont
call ->destroy() handler for us.
More generally, we want a transactional behavior for "tc qdisc
change ...", so prio_tune() should not make modifications if
any error is returned.
It means that we must validate parameters and allocate missing qdisc(s)
before taking root qdisc lock exactly once, to not leave the prio qdisc
in an intermediate state.
Fixes: cbdf451164 ("net_sched: prio: properly report out of memory errors")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski reported lockdep warning a spinlock
was not registered before being held in mlx4_cmd_wake_completions()
cmd.context_lock initialization is not at the right place.
1) mlx4_cmd_use_events() can be called multiple times.
Calling spin_lock_init() on a live spinlock can lead
to hangs.
2) mlx4_cmd_wake_completions() can be called while lock
has not been initialized.
Lockdep complains, and current logic is not race prone.
It seems better to move the initialization earlier in
mlx4_load_one()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nft_genmask_cur has already done left-shift operator on the gencursor,
so there's no need to do left-shift operator on it again.
Fixes: ea4bd995b0 ("netfilter: nf_tables: add transaction helper functions")
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we add a nft rule like follows:
# nft add rule filter test tcp dport vmap {1: jump test}
-ELOOP error will be returned, and the anonymous set will be
destroyed.
But after that, nf_tables_abort will also try to remove the
element and destroy the set, which was already destroyed and
freed.
If we add a nft wrong rule, nft_tables_abort will do the cleanup
work rightly, so nf_tables_set_destroy call here is redundant and
wrong, remove it.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang says:
"Users may add such a wrong nft rules successfully, which will cause an
endless jump loop:
# nft add rule filter test tcp dport vmap {1: jump test}
This is because before we commit, the element in the current anonymous
set is inactive, so osp->walk will skip this element and miss the
validate check."
To resolve this problem, this patch passes the generation mask to the
walk function through the iter container structure depending on the code
path:
1) If we're dumping the elements, then we have to check if the element
is active in the current generation. Thus, we check for the current
bit in the genmask.
2) If we're checking for loops, then we have to check if the element is
active in the next generation, as we're in the middle of a
transaction. Thus, we check for the next bit in the genmask.
Based on original patch from Liping Zhang.
Reported-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Liping Zhang <liping.zhang@spreadtrum.com>
We should check "i" is used as a dictionary or not, "binding" is already
checked before.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I forgot to move the kmem_cache_destroy into the exit path.
Fixes: 0c5366b3a8 ("netfilter: conntrack: use single slab cache)
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Nicolas Dichtel says:
====================
ovs: fix rtnl notifications on interface deletion
There was no rtnl notifications for interfaces (gre, vxlan, geneve) created
by ovs. This problem is fixed by adjusting the creation path.
v1 -> v2:
- add patch #1 and #4
- rework error handling in patch #2
====================
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang Grandegger