Repair any formatting/style issues that can be fixed without major
code refactoring.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output volume limits allow signals to be limited to specific levels
appropriate for the hardware attached. As this is a property of the
hardware itself these will be configured through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all the audio related device tree entries are handled by the
MFD code, for most parts of the Arizona driver we group the device
tree handling with the component that uses it and should do so here as
well.
Add handling in the ASoC code for the audio device tree entries, a
later patch removes the MFD side handling but there is no harm in it
being duplicated temporarily.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver has quite a few small initialisation functions, in
preparation for some refactoring add a new function arizona_init_common.
This will be used bus probe level initialisation that is common across
Arizona devices. For now just move the notifier chain initialisation in
there.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mask rather than the shift is accidentally passed to the
SOC_ENUM_SINGLE macro which results in the wrong bits being set for this
control, change to using the shift to correct this.
Signed-off-by: Sapthagiri Baratam <sapthagiri.baratam@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to modify the state of some of our own pins and are currently
not taking account that the pin name may have a name_prefix applied
to it.
Replace the snd_soc_dapm_x_pin functions with the equivalent
snd_soc_component_x_pin functions so that any name_prefix will be
handled automatically.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are very thin wrappers around core functions, so they
make sense as inline functions. Also making them inline avoids build
issues in the case where the machine driver is built in but the CODEC
is built as a module.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
enable the source clocks for FLLs as they are powered up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The later Arizona parts do run write sequences to power up and down the
speaker path as such a delay needs to be inserted into the DAPM sequence
to allow this to run. This patch adds appropriate delays into the
existing coalesced delay scheme.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When debugging it is useful to check the total power up/down delay that
is executed as part of the coalesced output delay. This patch adds some
debug prints for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For best performance changing the synchroniser state whilst the FLL is
running should be avoided. As this has been done fairly regularly in
practice rather than hard preventing this, simply improve the FLL enable
sequence and give a warning if the user changes the synchroniser state.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for future improvements allow a base to be passed to
arizona_is_enabled_fll, this will allow it to be used to check the state
of the synchroniser path as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Theta/lambda is used to give the fractional portion of the FLL
frequency multiplication. When the synchroniser is active the
reference path lambda value is hard coded in the hardware to
65536. This patch corrects the handling of theta such that it
is scaled to match this denominator, when the synchroniser is
active.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When enabling an FLL use pm_runtime_get_sync() instead of
pm_runtime_get() to ensure that all the register settings
have been written out and the codec is powered-up before
we write the enable bit.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When reclocking an active FLL, to ensure a clean transition, do
not change the gain setting until we have entered free run.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A recent commit made a few arrays 'const', but also added the
same attribute to a function return type, where it makes no
sense, and we get a warning when building with W=1:
sound/soc/codecs/arizona.c:1725:27: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
static const char * const arizona_dai_clk_str(int clk_id)
This removes it again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The OUT4L and OUT4R widgets are not registered PRE_PMU or POST_PMD
events, as such the manual speaker enable on wm5102 does not actually
ever run. Furthermore since the issue actually only affected rev B of
the silicon which never shipped in volume, simply remove the work around
from the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some situations the voice control firmware will by used
to only provide a trigger notification event. In this case a
compressed stream will not be opened by user-space, as such we
need to provide a virtual output to power on the DSP in this
use-case. This patch adds a virtual output 'DSP Voice Trigger'
that can be used for this, and a switch that lets it be connected
to the core when required.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a notifier chain that can be used from the machine driver to catch
events generated by the CODEC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bits in the ARIZONA_CLOCK_CONTROL register only respond to writes of
a '1', a write of '0' is ignored. So there's no need to use update_bits.
We can do a simple write to set bits.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up an FLL in pseudo-fractional mode it is preferred
to use a lower FRATIO if possible to give a higher reference clock
frequency. This patch swaps the two loops in arizona_calc_fratio()
so that lower FRATIOs are tried first. The decrementing loop is also
changed to start from init_ratio because the original settings might
already give a fractional value for N.K
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS47L24 and WM1831 codecs only use the OUT4L widget so we can
skip creation of the OUT4R widget.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The debug logging of FLL calculations was confusing. Values were
printed in hex without indicating this by a leading 0x, and
despite these normally being required in decimal. Also where the
register value isn't the actual value (it s a power-of-two or
0 means 1, 1 means 2, ...) it was unclear whether the actual or
register value was shown.
This patch changes the log print so that all mathematical values
are shown in decimal, all register values are shown in hex with a
0x prefix, and where the register value isn't the actual integer
value the decimal integer value is shown in () after the hex
register value.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the FLL is in pseudo-fractional mode there is an additional
limit on fref based on the fratio, to prevent aliasing around the
Nyquist frequency. If fref exceeds this limit the refclk divider
must be increased and the calculation tried again until a suitable
combination of fref and fratio is found or we have to fall back to
integer mode.
This patch also adds some debug log prints around this code.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona CODECs support several rates that do not have simple defines
in ALSA. This patch adds support for SNDRV_PCM_RATE_KNOT so that users
can open stream at these rates. As part of this we should always set
constraints in arizona_startup, currently we only set the constraints if
we already have a clock to limit rates to that family of sample rates.
This patch updates this to set a constraint of all rates supported by
the chip if we do not already know which family of rates to limit to.
Finally we also reduce the list of rates supported in the constraints to
only include those that are supported on current parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWee4AAAoJECTWi3JdVIfQwPkH/jMpijne8cfnOm0jQ0WyvXPd
HSig93ZAJ2x/+uR7yrmF2BsxhnT6G1lmDb2zxYhHGEAMyBtdA/xtOjO1wTRjXgIo
9p7ui66uP/sAW+NfHsvXVyf/8vV9nw8t0CsyBf+ijynz6MiDigQR7e8RA7xZR7oQ
oBabHPZb85OJjxmn2XlqaxUoxNhBdAS3gNoctMy9VZDwSLiunOvYTGBoBA43LQk6
6DN5VRu7wg05ruN6t5xZ5bd5WAtvgN+tSsRAabmunWDnILCa8OaOmzWPv3QITIva
PQLauiya4N0/YgyNGYaBY/6pc5u9SHzq0caYUq0I6WY6Phjo7wfU8/+y4NqUPn4=
=d18k
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.5' into asoc-next
ASoC: Updates for v4.5
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
# gpg: Signature made Wed 23 Dec 2015 00:42:40 GMT using RSA key ID 5D5487D0
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
commit 9b8ef9f6b3 ("ASoC: dapm: Add startup & shutdown for dai_links")
Added support for calling startup on CODEC to CODEC links, however this
is called with a NULL runtime pointer. There isn't really a sensible way
to pass a valid runtime pointer to a CODEC to CODEC link at the moment,
so we need to make the startup function safe for NULL runtimes.
This patch returns from the Arizona startup function early if there is no
runtime, this is perfectly safe as all the startup function does is set
the PCM constraints for user-space which arn't relevant to a CODEC to
CODEC link anyway.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For a sample rate of 12kHz the bclk was taken from the 44.1kHz table as
we test for a multiple of 8kHz. This patch fixes this issue by testing
for multiples of 4kHz instead.
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch rearranges the switch statement in arizona_calc_fratio so
that older codecs are the special cases, with the default case
applying to newer codecs (WM8998 and later). This is preferable
because it avoids having to patch new cases in every time a new
codec is added.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both the sysclk and asyncclk members of arizona_priv are signed by we
refer to them through an unsigned pointer. This patch fixes this small
harmless error.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, various places in Arizona use "const char *" and "int".
This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When switching between two clock sources using the FLL freerun to smooth
the transition we should wait 32uS after putting the FLL into freerun
before we proceed. In practice we appear to be getting enough delay from
the surrounding code, but better to make it explicit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm5110 device contains a hardware ANC block, this patch connects up
controls and routing for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code was able to generate illegal OPCLK_REF values because the
reference frequency tables listed all values of SYSCLK instead of
valid values for OPCLK_REF clock. The maximum OPCLK_REF clock is
49.152MHz or 45.1584MHz.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We will occasionally require to take different action based on if an
input is analog or digital so add a helper function to return if an
input is analog.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the addition of the WILL_PMU / WILL_PMD several of the switches in
arizona.c no longer cover all cases or have a default case. Whilst this
isn't causing any problems in the interests of robustness add default
cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax