drop smc pin state change code, pin state will be saved in pinctrl-adi2 driver
cleanup nor flash init/exit for pm suspend/resume
Signed-off-by: Steven Miao <realmz6@gmail.com>
Spi v3 controller is not only used on Blackfin. So rename it
and use ioread/iowrite api to make it work on other platform.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gvaS
-----END PGP SIGNATURE-----
Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao:
"Some minor changes and bug fixes"
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
From: Eunbong Song <eunb.song@samsung.com>
Add platfrom device resource for bfin-sport on bf533 stamp
fix build error for bf527-ezkit_defconfig for old silicon
blackfin: Support L1 SRAM parity checking feature on bf60x
blackfin: bf609: update the anomaly list to Nov 2013
blackfin: delete non-required instances of <linux/init.h>
From: Paul Walmsley <pwalmsley@nvidia.com>
06/18] smp, blackfin: kill SMP single function call interrupt
arch: blackfin: uapi: be sure of "_UAPI" prefix for all guard macros
Move code for the SEC faults from the IRQ hanlders into IRQ actions.
refine bfin fault routine handle
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
blackfin: bf60x: clock: return 0 upon error from clk_round_rate()
clk_round_rate() should return 0 upon an error, rather than returning
a negative error code. This is because clk_round_rate() is being
changed to return an unsigned return type rather than a signed type,
since some clock sources can generate rates higher than (2^31)-1 Hz.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
stmmac callbacks have been extended for better separation.
Update them to avoid breakage.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The serial driver sets up port function manually in early platform probe stage
if the ADI GPIO2 driver is used. Remove the bfin_sport_uart early platform
devices.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Remove gpio driver for new gpio controller on BF54x and BF60x.
Build the bfin_gpio driver only when other BF5xx processors are selected.
Replace the prefix of some gpio and peripheral functions with adi.
add portmux platform data in machine portmux.h
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
- Enable GMAC
- Set propler DMA PBL
- Disable DMA store and forward mode
- Select PTP input clock from MII
clock.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
If SCB exists in select blackfin cpu, developer can change the SCB
priority in kernel configuration.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The use of V4L2_IN/OUT_CAP_CUSTOM_TIMINGS is obsolete, use DV_TIMINGS instead.
Note that V4L2_IN/OUT_CAP_CUSTOM_TIMINGS is just a #define for
V4L2_IN/OUT_CAP_DV_TIMINGS.
At some point in the future these CUSTOM_TIMINGS defines might be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Append the SEC IRQ after the IVG6, which is consistent to BF5xx SIC.
Exclude SIC irqchip fucntions from SEC code.
Call handle_fasteoi_irq in SEC error and fault handler.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Pull blackfin update from Bob Liu.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
Blackfin: smp: add smp_mb() to keep coherency
Blackfin: drop irq enable in init_arch_irq()
Blackfin: fix wrong place disabled irq
Blackfin: update defconfig for bf609-ezkit
Blackfin: add bf548 v0.4 revision
Blackfin: bf60x: Add bf608 and bf609 specific perpheral MMRs
Blackfin: cpufreq: fix dpm_state_table
Blackfin: bfin_gpio: proc: fix return value
Blackfin: CM-BF537E: Update SPORT support in board file.
Blackfin: bf537: fix lq035 platform device name
Blackfin: bf533-ezkit: enable flash drivers by default
Change ce pin to PE4 according to new adaptor board and re-define ppi for vs6624
to avoid gpio conflict.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Customize the SEC interrupt priority array in machine ints-priority.c.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Turn SEC related macro CONFIG_BF60x into SEC_GCTL.
Move machine specific GPIO_PINT macros to machine gpio header.
Split SEC init_arch_irq() and vec_to_irq() from old SIC.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
PPI driver has changed blank units from clocks to pixels.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
save and restore pint sec CTL
save and restore pint registers
add pint suspend and resume when suspend to mem
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Sonic Zhang