The ASPEED SoC must deassert a reset in order to use the ADC peripheral.
The device tree bindings are updated to document the resets phandle, and
the example is updated to match what is expected for both the reset and
clock phandle. Note that the bindings should have always had the reset
controller, as the hardware is unusable without it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Maxim MAX30105 part adds a third LED (green) and uses a multi-LED
measuring mode producing three measurements
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Current code assumes always 2 measurements (6 bytes) have to be copied,
prepare for more flexibility
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the programming of the mode setting from init() to
buffer_postenable()
Split out a separate function to
only update the power/shutdown bit
This changes permits to more easily implement different
modes of measurements in further patches
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Chip must not be in shutdown for reading temperature, so briefly leave
shutdown if buffer is not already running
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stalder <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Table 4 of the datasheet specifies the mode control, these are not
individual bits; add multi LED mode
Add multi-LED mode and fix MODE_MASK (3 bits wide, not 2)
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32H7 ADC channels can be configured either as single ended or
differential with 'st,adc-channels' or 'st,adc-diff-channels'
(positive and negative input pair: <vinp vinn>, ...).
Differential channels have different offset and scale, from spec:
raw value = (full_scale / 2) * (1 + (vinp - vinn) / vref).
Add offset attribute.
Differential channels are selected by DIFSEL register. Negative
inputs must be added to pre-selected channels as well (PCSEL).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove const array that defines channels. Build channels definition
at probe time, when initializing channels (only for requested ones).
This will ease adding differential channels support.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reducing shunt and bus voltage range improves the accuracy, so allow
altering the default settings.
Both settings are exposed as gain values. While for the shunt voltage
this is straightforward, the bus range settings of 32V (default) and 16V
are mapped to gain values of 1 resp. 2, to provide a uniform API to
userspace.
As the gain settings are incorporated into the raw values by the sensor
itself, adjusting of the scale attributes is not necessary.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While the config uses the physical value corresponding to the LSB
for both the power and the bus voltage register, the shunt voltage is
specified as parts of 1 mV. Use the LSB physical value for all registers.
No functional change.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lower bits of the INA219/220 bus voltage register are conversion
status flags, properly shift the value.
When reading via IIO buffer, the value is passed on unaltered,
shifting is the responsibility of the user.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new ACPI ID for ak9911 as had been found on prototype board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new ACPI ID for sx9500 as had been found on prototype board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename structs holding event configuration registers
to more appropriate names. This naming is consistent
with the event config register names given in the
mma845x and fxls8471 datasheets.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename time step look up struct to generic name
as the values in the look table are same for all
the other events like pulse, transient etc.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver for 20-bit ALS and UV B sensor with I2C interface exposing
the following API:
in_uvindex_input
in_illuminance_raw
in_illuminance_scale
in_illuminance_scale_available
in_intensity_uv_raw
in_intensity_uv_scale
in_intensity_uv_scale_available
integration_time
integration_time_available
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397962
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix gcc warnings about variable 'ec_device' being set but not used
in these files:
common/cros_ec_sensors/cros_ec_sensors.c:194:25
light/cros_ec_light_prox.c:184:25
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Need to acknowledge DRDY irq in direct mode/ software
triggered mode. Otherwise, on the next conversion, overrun
flag will be raised, which is not a correct state.
This doesn't affect the functionality, but will generate
possible incorrect overrun reports.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for DMA transfers. The implementation uses the user watermark
to decide whether DMA will be used or not. For watermark 1, DMA will not be
used. If watermark is bigger, DMA will be used.
Sysfs attributes are created to indicate whether the DMA is used,
with hwfifo_enabled, and the current DMA watermark is readable
in hwfifo_watermark. Minimum and maximum values are in hwfifo_watermark_min
and hwfifo_watermark_max.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The module license checker complains about these two so just fix
it up. They are both GPLv2, both written by me or using code
I extracted while refactoring from the GPLv2 drivers.
Cc: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)
-----BEGIN PGP SIGNATURE-----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=+tMO
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A couple of configfs cleanups:
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)"
* tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs:
RDMA/cma: make config_item_type const
stm class: make config_item_type const
ACPI: configfs: make config_item_type const
nvmet: make config_item_type const
usb: gadget: configfs: make config_item_type const
PCI: endpoint: make config_item_type const
iio: make function argument and some structures const
usb: gadget: make config_item_type structures const
dlm: make config_item_type const
netconsole: make config_item_type const
nullb: make config_item_type const
ocfs2/cluster: make config_item_type const
target: make config_item_type const
configfs: make ci_type field, some pointers and function arguments const
configfs: make config_item_type const
configfs: Fix bool initialization/comparison
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
-----BEGIN PGP SIGNATURE-----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=IXO+
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of new device support, cleanups and features for IIO in the 4.15 cycle
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
The two properties unique to each supported chip, resolution and number
of channels, are currently gleaned from the chip's name.
E.g. dac102s085 is a dual channel 10-bit DAC.
^^^
This was deemed unmaintainable by the subsystem maintainer once the
driver is extended to support further chips, hence it was requested
to add an explicit table for chip-specific information and use an
enum to reference into it.
This adds 17 LoC without any immediate gain, so make the change in a
separate commit which can be reverted if we determine in 10 years that
it was unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DACrrcS085 (rr = 08/10/12, c = 2/4) family of SPI DACs was
inherited by TI when they acquired National Semiconductor in 2011.
This driver was developed for and tested with the DAC082S085 built into
the Revolution Pi by KUNBUS, but should work with any of the other
chips as they share the same programming interface.
There is also a family of I2C DACs with just a single channel called
DACrr1C08x (rr = 08/10/12, x = 1/5). Their programming interface is
very similar and it should be possible to extend the driver for these
chips with moderate effort. Alternatively they could be integrated into
ad5446.c. (The AD5301/AD5311/AD5321 use different power-down modes but
otherwise appear to be comparable.)
Furthermore there is a family of 8-channel DACs called DACrr8S085
(rr = 08/10/12) as well as two 16-bit DACs called DAC161Sxxx
(xxx = 055/997). These are more complicated devices with support for
daisy-chaining and the ability to power down each channel separately.
They could either be handled by a separate driver or integrated into the
present driver with a larger effort.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() return NULL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't populate const array ch_to_mux on the stack, instead
make it static. Makes the object code smaller by over 200 bytes:
Before:
text data bss dec hex filename
12663 1648 128 14439 3867 drivers/iio/adc/ti-adc12138.o
After
text data bss dec hex filename
12353 1744 128 14225 3791 drivers/iio/adc/ti-adc12138.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add check on STM32 ADC clock rate to report an explicit error.
This may avoid division by 0 later in stm32-adc driver.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add TIM15_TRGO trigger that is now supported on STM32H7.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make the argument of the functions iio_sw{d/t}_group_init_type_name const
as they are only passed to the function config_group_init_type_name having
the argument as const.
Make the config_item_type structures const as they are either passed to
the functions having the argument as const or they are
stored in the const "ci_type" field of a config_item structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add driver to support older EC firmware that only support deprecated
ec command. Rely on ACPI memory map register to access sensor
information.
Present same interface as the regular cros_ec sensor stack:
- one iio device per accelerometer
- use HTML5 axis definition
- use iio abi units
- accept calibration calls, but do nothing
Chrome can use the same code than regular cros_ec sensor stack to
calculate orientation and lid angle.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This fix allows platforms to probe correctly even if the
trigger edge property is missing. The hardware trigger
will no longer be registered in the sybsystem
Preserves backwards compatibility with the support that
was in the driver before the hardware trigger.
https://storage.kernelci.org/mainline/master/v4.14-rc2-255-g74d83ec2b734/arm/sama5_defconfig/lab-free-electrons/boot-at91-sama5d2_xplained.txt
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: 5e1a1da0f ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One of the user complained that on his system Thinkpad Yoga S1, with
commit f1664eaace ("iio: hid-sensor-trigger: Fix the race with user
space powering up sensors") causes the system to resume immediately
on suspend (S3 operation). On this system the sensor hub is on USB
and is a wake up device from S3. So if any sensor sends data on
motion, the system will wake up. This can be a legitimate use case
to wake up device motion, but that needs proper user space support
to set right thresholds.
In fact the above commit didn't cause this regression, but any operation
which cause sensors to wake up would have caused the same issue. So if
user reads the raw sensor data, same issue occurs, with or without this
commit. Only difference is that the above commit by default will trigger
a power up and power down of sensors as part of runtime pm enable
(runtime enable will cause a runtime resume callback followed by
runtime_suspend callback). Previously user has to do some action on
sensors.
On investigation it was observed that the current driver correctly
changing the state of all sensors to power off but then also some sensor
will still send some data. Only option is to never power up any sensor.
Only good option is to:
- Using sysfs interface disable USB as a wakeup device (This will not
need any driver change)
Since some user don't care about sensors. So for those users this change
brings back old functionality. As long as they don't cause any operation
to power up sensors (like raw read or start iio-sensor-proxy service),
the sensors will not be to touched. This is done by delaying run time
enable till user space does some operation with sensors.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196853
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver for RF Digital RFD77402 VCSEL (vertical-cavity surface-emitting
laser) Time-of-Flight (ToF) sensor to measure distance up to 2 m with
millimeter precision
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS3DHH accel sensor
http://www.st.com/resource/en/datasheet/lis3dhh.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not try to configure sample frequency if the sensor do not export
odr register address in register map. That change will be used to
properly support LIS3DHH accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define st_sensor_int_drdy structure in st_sensor_data_ready_irq in order
to contain irq line parameters of the device.
Moreover separate data-ready open-drain configuration parameters for INT1
and INT2 pins in st_sensor_data_ready_irq data structure.
That change will be used to properly support LIS3DHH accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
to STM pressure framework
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information to
LIS3MDL magn sensor
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
to STM gyroscope framework
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS2DW12 accelerometer in
st_accel framework
http://www.st.com/resource/en/datasheet/lis2dw12.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New devices (e.g. LIS2DW12) enable all axis by default and do not export
that capability in register map. Check if the enable_axis register
address has been declared in st_sensor_settings map in order to verify if
the driver needs to enable all sensor axis
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate data-ready configuration parameters for INT1 and INT2 pins in
st_sensor_data_ready_irq data structure. That change will be use to
properly support LIS2DW12 accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but
in reality their resolution is 21 bit with an overrange or underrange
of 12% beyond Vref. In other words, "full scale" means +/- 2^20.
This driver does not explicitly signal back to the user when an
overrange or underrange occurs, but the user can detect it by comparing
the raw value to +/- 2^20 (or the scaled value to Vref).
The chips feature an extended temperature range and high accuracy,
low noise characteristics, but their conversion times are slow with
up to 80 ms +/- 2% (on the MCP3550-50).
Hence, unlike the other ADCs supported by the driver, conversion does
not take place in realtime upon lowering CS. Instead, CS is asserted
for 8 usec to start the conversion. After waiting for the duration of
the conversion, the result can be fetched. While waiting, control of
the bus is ceased so it may be used by a different device.
After the result has been fetched and 10 us have passed, the chip goes
into shutdown and an additional power-up delay of 144 clock periods is
then required to wake the analog circuitry upon the next conversion
(footnote below table 4-1, page 16 in the spec).
Optionally, the chips can be used in so-called "continuous conversion
mode": Conversions then take place continuously and the last result may
be fetched at any time without observing a delay. The mode is enabled
by permanently driving CS low, e.g. by wiring it to ground. The driver
only supports "single conversion mode" for now but should be adaptable
to "continuous conversion mode" with moderate effort.
The chips clock out a 3 byte word, unlike the other ADCs supported by
the driver which all have a lower resolution than 16 bit and thus make
do with 2 bytes. Calculate the word length on probe by rounding up the
resolution to full bytes. Crucially, if the clock idles low, the
transfer is preceded by a useless Data Ready bit which increases its
length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec).
Autosense this based on the SPI slave's configuration.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the ABI documentation, the shunt resistor value should be
specificied in Ohm. As this is also used/documented for the MAX9611,
use the same for the INA2xx driver.
This poses an ABI break for anyone actually altering the shunt value
through the sysfs interface, it does not alter the default value nor
a value set from the devicetree.
Minor change: Fix comment, 1mA is 10^-3A.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce FIFO ops data structure to contain FIFO related parameters
in order to properly support more devices in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move FIFO decimator info in st_lsm6dsx_sensor_settings list since
decimator registers are exported in register map just in
lsm6ds3/lsm6ds3h/lsm6dsl/lsm6dsm sensors and not in other compliant
devices
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate fifo mode and max fifo sample rate configuration.
That change will be necessary to reuse st_lsm6dsx_set_fifo_mode()
routine and to support more devices in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Express max fifo depth in ST_LSM6DSX_SAMPLE_SIZE instead of in bytes.
That change will be necessary to properly support more devices
in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the of_device_get_match_data() helper instead of open coding.
Note that the rcar-gyroadc driver is used with DT only, so there's
always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The rcar-gyroadc driver compiles fine on other platforms, hence increase
compile coverage.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On 64-bit:
drivers/iio/adc/rcar-gyroadc.c: In function 'rcar_gyroadc_parse_subdevs':
drivers/iio/adc/rcar-gyroadc.c:352:15: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
childmode = (unsigned int)of_id->data;
^
Cast the pointer to uintptr_t instead of unsigned int to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reported scale was only correct for the default settings of 100 ms
integration time and gain 1.
This aligns the reported scale with the behaviour of any other IIO driver
and the documented ABI, but may require userspace changes if someone uses
non-default settings.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of manually iterating the array of allowed gain values, use
find_closest. Storing the current gain setting avoids accessing the
hardware on each query.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of reading the value from the register on each query, store the
set value.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This improves code uniformity (range checks for als_gain are also done
in the setter). Also unmangle rounding and calculation of register value.
The calculated integration time it_ms is required in the next patch of
the series.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
KXTF9 has mostly compatible register layout to KXCJK accelerometer.
There is no motion direction interrupt support, but there is tap
direction detection instead (not implemented in this patch).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make sampling_frequency_avail per-type - like sampling_frequency is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation for KXTF9 support, make sampling_frequency_avail
attribute dynamic.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extract reporting of motion event direction from interrupt handler,
as it is not supported by KXTF9.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix INT_CTRL1 bit names to match register name and add names
for INT_SRC1 bits.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor ODR/WUF setting code in preparation of KXTF9 support.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'mma8452_read_thresh' and 'mma8452_write_thresh' functions
does more than just read/write threshold values.
They also handle IIO_EV_INFO_HIGH_PASS_FILTER_3DB and
IIO_EV_INFO_PERIOD therefore renaming to generic names.
Improves code readability, no impact on functionality.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch, forgetting to put a thermal-zones DT node would
result in the driver failing to probe.
It should be perfectly acceptable to have the driver probe even if no
thermal-zones DT is found. However, it shouldn't want to fail if the
thermal registering fail for any other reason (waiting for other drivers
for example) so check on ENODEV only.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver has a get_temp function used by the thermal framework that
uses pm functions.
However, the driver isn't registered in pm before it is registered in
thermal framework, resulting in the pm_resume not being called and thus
the IP not enabled.
When the IP is disabled, the raw temp value is always 0. With the
devices currently supported, it isn't a problem since with their
respective formula, they return a really cold SoC temperature which
isn't a problem for the thermal framework. But for future SoC that have
a different formula, it could return a critically hot temperature,
forcing the thermal framework to shutdown the board.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch provides an iio device driver for DS4422/DS4424 chips that support
two/four channel 7-bit Sink/Source Current DAC.
Signed-off-by: Ismail H. Kose <Ismail.Kose@maximintegrated.com>
Signed-off-by: Ismail H. Kose <ihkose@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dln2-adc driver uses interface(s) that are controlled by the
IIO_TRIGGERED_BUFFER Kconfig symbol, so the driver needs to select
that symbol to prevent the build error.
drivers/iio/adc/dln2-adc.o: In function `dln2_adc_probe':
dln2-adc.c:(.text+0x528): undefined reference to `devm_iio_triggered_buffer_setup'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing break in iio_simple_dummy_write_event_config() for the voltage
threshold event enable attribute. Without this writing to the
in_voltage0_thresh_rising_en always returns -EINVAL even though the change
was correctly applied.
Fixes: 3e34e650db ("iio: dummy: Demonstrate the usage of new channel types")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements have gone away.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc 4.1.2:
drivers/iio/pressure/zpa2326.c: In function ‘zpa2326_wait_oneshot_completion’:
drivers/iio/pressure/zpa2326.c:868: warning: ‘ret’ may be used uninitialized in this function
When testing for "timeout < 0", timeout is already guaranteed to be
strict negative, so the branch is always taken, and ret is thus always
initialized. But (some version of) gcc is not smart enough to notice.
Remove the check to fix this.
As there is no other code in between assigning the error codes and
returning them, the error codes can be returned immediately, and the
intermediate variable can be dropped.
Drop the "else" to please checkpatch.
Fixes: e7215fe4d5 ("iio: pressure: zpa2326: report interrupted case as failure")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Most applications are too noisy to allow the default noise and
watchdog settings, and thus need to be configurable via DT
properties.
Also default settings to POR defaults on a reset, and register
distuber interrupts as noise since it prevents proper usage.
Cc: devicetree@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
If an IIO device returns an error code for a read access via debugfs, it
is currently ignored by the IIO core (other than emitting an error
message). Instead, return this error code to user space, so upper layers
can detect it correctly.
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The serial interface can be reset by writing 32 consecutive 1s to the device.
'ret' was initialized correctly but its value was overwritten when
ad7793_check_platform_data() was called. Since a dedicated reset function
is present now, it should be used instead.
Fixes: 2edb769d24 ("iio:ad7793: Add support for the ad7798 and ad7799")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ctrl_reg register needs to be written after any write to
the humidity registers. The value written to the ctrl_reg register
does not necessarily need to change, but a write operation must
occur.
The regmap_update_bits functions will not write to a register
if the register value matches the value to be written. This saves
unnecessary bus operations. The change in this patch forces a bus
write during the chip_config operation by switching to
regmap_write_bits.
This will fix issues where the Humidity Sensor Oversampling bits
are not updated after initialization.
Signed-off-by: Colin Parker <colin.parker@aclima.io>
Acked-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
returns a signed voltage from mcp320x_adc_conversion() but neglects that
the caller interprets a negative return value as failure. Only mcp3301
(and the upcoming mcp3550/1/3) is affected as the other chips are
incapable of measuring negative voltages.
Fix and while at it, add mcp3301 to the list of supported chips at the
top of the file.
Fixes: f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
Cc: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver calls spi_get_drvdata() in its ->remove hook even though it
has never called spi_set_drvdata(). Stack trace for posterity:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
Internal error: Oops: 5 [#1] SMP ARM
[<8072f564>] (mutex_lock) from [<7f1400d0>] (iio_device_unregister+0x24/0x7c [industrialio])
[<7f1400d0>] (iio_device_unregister [industrialio]) from [<7f15e020>] (mcp320x_remove+0x20/0x30 [mcp320x])
[<7f15e020>] (mcp320x_remove [mcp320x]) from [<8055a8cc>] (spi_drv_remove+0x2c/0x44)
[<8055a8cc>] (spi_drv_remove) from [<805087bc>] (__device_release_driver+0x98/0x134)
[<805087bc>] (__device_release_driver) from [<80509180>] (driver_detach+0xdc/0xe0)
[<80509180>] (driver_detach) from [<8050823c>] (bus_remove_driver+0x5c/0xb0)
[<8050823c>] (bus_remove_driver) from [<80509ab0>] (driver_unregister+0x38/0x58)
[<80509ab0>] (driver_unregister) from [<7f15e69c>] (mcp320x_driver_exit+0x14/0x1c [mcp320x])
[<7f15e69c>] (mcp320x_driver_exit [mcp320x]) from [<801a78d0>] (SyS_delete_module+0x184/0x1d0)
[<801a78d0>] (SyS_delete_module) from [<80108100>] (ret_fast_syscall+0x0/0x1c)
Fixes: f5ce4a7a92 ("iio: adc: add driver for MCP3204/08 12-bit ADC")
Cc: Oskar Andero <oskar.andero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove rounding configuration since it is enabled by default for the
FIFO output registers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove Latched Interrupt configuration since it is enabled by default
for FIFO watermark interrupt
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit adds mt2712 compatible node.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update odr value in st_lsm6dsx_sensor data structure just in
st_lsm6dsx_write_raw() in order to avoid to set the same value
multiple times
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace 'unsigned' with 'unsigned int'
to improve code readability.
Issue found by checkpatch.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace symbolic permissions with octal permissions
to improve code readability.
Issue found by checkpatch.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a bad error check when counting 'st,adc-channels' array elements.
This is seen when all channels are in use simultaneously.
Fixes: 64ad7f643 ("iio: adc: stm32: introduce compatible data cfg")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Balance timer start routine that sets ARPE: clear it in stop routine.
This fixes a corner case, when timer is used successively as trigger
(with sampling_frequency start/stop routines), then as a counter
(with preset).
Fixes: 93fbe91b55 ("iio: Add STM32 timer trigger driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, setting preset value (ARR) will update directly 'Auto reload
value' only on 1st write access. But then, ARPE is set. This makes
ARR a shadow register. Preset value should be updated upon each
write request: ensure ARPE is 0. This fixes successive writes to
preset attribute.
Fixes: 4adec7da05 ("iio: stm32 trigger: Add quadrature encoder device")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If we can not enable the regulator, go through the error handling path
instead of silently continuing.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 7cc97d77ee has introduced a call to 'regulator_disable()' in the
.remove function.
So we should also have such a call in the .probe function in case of
error after a successful 'regulator_enable()' call.
Add a new label for that and use it.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If 'devm_regulator_get()' fails, we should go through the existing error
handling path instead of returning directly, as done is all the other
error handling paths in this function.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix gcc warning:
cros_ec_baro.c:130:25: warning: variable ‘ec_device’ set but not used
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver sets a .data pointer for each .compatible string but never
calls of_device_get_match_data(). Instead, ADC properties are looked up
with spi_get_device_id(). The .data pointer is therefore unnecessary,
so drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Single-channel converters such as mcp3001, mcp3201, mcp3301 and the
upcoming mcp3550/1/3 lack a MOSI pin, so there's no need to call
mcp320x_channel_to_tx_data() for them.
Moreover, instead of calling spi_read() for these converters, which
generates an spi_message and spi_transfer on the stack on every readout,
it's more efficient to use the spi_message and spi_transfer[] included
in struct mcp320x (as we do for multi-channel ADCs), but initialize the
spi_message only with the receive transfer.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add data ready trigger for hardware interrupts that signal
new, available measurement samples.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports multiple devices like mma8653,
mma8652, mma8452, mma8453 and fxls8471. Almost all
these devices have more than one event.
Current driver design hardcodes the event specific
information, so only one event can be supported by this
driver at any given time.
Also current design doesn't have the flexibility to
add more events.
This patch improves by detaching the event related
information from chip_info struct,and based on channel
type and event direction the corresponding event
configuration registers are picked dynamically.
Hence both transient and freefall events can be
handled in read/write callbacks.
Changes are thoroughly tested on fxls8471 device on imx6UL
Eval board using iio_event_monitor user space program.
After this fix both Freefall and Transient events are
handled by the driver without any conflicts.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Texas Instruments DAC7512 has the exact same pinout, programming
interface and power-down modes as the Texas Instruments DAC121S101 and
Analog Devices AD5320, which are already supported by the IIO driver
ad5446.c. Remove the duplicate misc driver.
This requires user space to migrate to the standardized IIO sysfs ABI.
(In other words, it needs to change a filename.)
The IIO driver supports the chip's features more fully, e.g. the ability
to power down the output or choose one of the available powerdown modes.
There is an oddity with the misc driver in that it initializes the SPI
slave to SPI_MODE_0, in contradiction to the datasheet which specifies
that data is latched in on the falling edge, implying that SPI_MODE_1
or SPI_MODE_2 must be used. Another oddity is that Kconfig and the
MODULE_DESCRIPTION() claim the chip has 16-bit resolution although it
actually has 12-bit.
Datasheets:
http://www.ti.com/lit/ds/symlink/dac7512.pdfhttp://www.ti.com/lit/ds/symlink/dac121s101.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5320.pdf
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Pull HID update from Jiri Kosina:
- Wacom driver fixes/updates (device name generation improvements,
touch ring status support) from Jason Gerecke
- T100 touchpad support from Hans de Goede
- support for batteries driven by HID input reports, from Dmitry
Torokhov
- Arnd pointed out that driver_lock semaphore is superfluous, as driver
core already provides all the necessary concurency protection.
Removal patch from Binoy Jayan
- logical minimum numbering improvements in sensor-hub driver, from
Srinivas Pandruvada
- support for Microsoft Win8 Wireless Radio Controls extensions from
João Paulo Rechi Vita
- assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (28 commits)
HID: prodikeys: constify snd_rawmidi_ops structures
HID: sensor: constify platform_device_id
HID: input: throttle battery uevents
HID: usbmouse: constify usb_device_id and fix space before '[' error
HID: usbkbd: constify usb_device_id and fix space before '[' error.
HID: hid-sensor-hub: Force logical minimum to 1 for power and report state
HID: wacom: Do not completely map WACOM_HID_WD_TOUCHRINGSTATUS usage
HID: asus: Add T100CHI bluetooth keyboard dock touchpad support
HID: ntrig: constify attribute_group structures.
HID: logitech-hidpp: constify attribute_group structures.
HID: sensor: constify attribute_group structures.
HID: multitouch: constify attribute_group structures.
HID: multitouch: use proper symbolic constant for 0xff310076 application
HID: multitouch: Support Asus T304UA media keys
HID: multitouch: Support HID_GD_WIRELESS_RADIO_CTLS
HID: input: optionally use device id in battery name
HID: input: map digitizer battery usage
HID: Remove the semaphore driver_lock
HID: wacom: add USB_HID dependency
HID: add ALWAYS_POLL quirk for Logitech 0xc077
...
STM32 ADC supports hardware triggers like STM32 Low-Power Timer.
For instance, STM32H7 ADC may be triggered by instances 1, 2 or 3.
Add hardware triggered mode so Low-Power Timer Trigger driver can
validate device.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for STM32 Low-Power Timer, that can be used as counter
or quadrature encoder.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for LPTIMx_OUT triggers that can be found on some STM32
devices. These triggers can be used then by ADC or DAC.
Typical usage is to configure LPTimer as PWM output (via pwm-stm32-lp)
and have synchronised analog conversions with these triggers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't populate the arrays on the stack, instead make them static.
Makes the object code smaller by 135 bytes:
Before:
text data bss dec hex filename
15135 4240 128 19503 4c2f inv_mpu_core.o
After:
text data bss dec hex filename
14840 4400 128 19368 4ba8 inv_mpu_core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As user's guide "ADS1015EVM, ADS1115EVM, ADS1015EVM-PDK, ADS1115EVM-PDK
User Guide (Rev. B)" (http://www.ti.com/lit/ug/sbau157b/sbau157b.pdf)
states at page 16:
"Note that both the ADS1115 and ADS1015 have internal clocks with a ±10%
accuracy. If performing FFT tests, frequencies may appear to be incorrect
as a result of this tolerance range.", add those 10% to converion wait
time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no point writing ADS1015_CFG_REG when configuration
didn't change. Avoid that.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing break statement to prevent the code for case
IIO_CHAN_INFO_CALIBBIAS falling through to the default case.
Also, add a break to the default case for the switch within
case IIO_CHAN_INFO_CALIBBIAS.
Addresses-Coverity-ID: 1357377
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return values from call to devm_kzalloc() and devm_kmemup()
in order to prevent a NULL pointer dereference.
This issue was detected using Coccinelle and the following semantic patch:
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
Fixes: 7ba9df54b0 ("iio: multiplexer: new iio category and iio-mux driver")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The TCS3472 device provides interrupt signal for out-of-threshold events
with persistence filter.
This change adds interrupt support for the threshold events and enables
to configure the period of time by persistence filter.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SPI core has handled this for some time.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This has been handled by the spi core for some time.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This has been handled by the spi core for some time now.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This has been handled by the i2c core for some time.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This is now done through some macro magic by the core.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Peter Rosin <peda@axentia.se>
Data-ready line in LIS3MDL is routed to drdy pin and it is not possible
to select a different INT pin. st_sensors_set_dataready_irq() assumes
that if drdy int address is not exported in register map, irq trigger
is not supported by the sensor and hw_irq_trigger is always false.
Based on this configuration st_sensors_irq_thread does not consume
generated interrupt causing an unhandled irq.
Fix this taking into account status register address in
st_sensors_set_dataready_irq()
Fixes: 90efe05562 (iio: st_sensors: harden interrupt handling)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The comparator polarity field in config register is not correctly
initialized as per the interrupt trigger setting. Because the bitfield
definision is wrong and bit shifting is missed.
Fixes: d9f39babd8 ("iio: adc: ti-ads1015: add threshold event support")
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Note that stm32-timer-trigger has expanded rather beyond triggers
(to include encoder input counting for example) and hence has an
iio_info structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent is now done via macro magic when
the relevant register call is made. The actual structure
element will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent is now done via macro magic when
the relevant register call is made. The actual structure
element will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
element will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent is now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Clearly this set jumps across multiple areas, but inherently it
can't be grouped like the other sets in this series so I've done
all the stuff in the common directory together.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
There are a few cases where none of the callbacks are supplied and the
ops structure purely existed to provide the driver module.
Given that is done differently now, we don't need to have a trig_ops structure.
Allow for it not being there required a few additional sanity checks when
trying check if particular callbacks are set.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This trig_ops.owner assignment occurs in all trigger drivers and
can be simply automated using a macro as has been done in many
other places in the kernel.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Starting point in boiler plate reduction similar to that done for
many similar cases elsewhere in the kernel.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-iio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS1015 device provides programmable comparator that can issue an
interrupt on the ALERT pin. This change adds the iio threshold event
support for that feature.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, comparator settings, and etc. So only a
single event channel can be enabled at a time. Also enabling both buffer
and event are prohibited for simplicity.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While the iio buffer for the ti-ads1015 driver is enabled, reading the
raw ADC channel data is restricted. We usually use the
iio_device_claim_direct_mode()/iio_device_release_direct_mode() pair for
that.
This change consequently reverses the locking order for the driver's
private lock and indio_dev->mlock which acquired by
iio_device_claim_direct_mode() internally. But it's safe because there is
no other dependency between these locks.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_iio_triggered_buffer_setup to simplify the error path in the
probe() and remove() function.
This changes the remove order, but the end result of remove function
actually does the reverse of probe.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a helper function to set conversion mode as there are a fair
number of users.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own scale information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's scale information immediately overwrites the current PGA
setting in the config register.
It is harmless because the correct PGA settings are reloaded just before
getting adc result anyway. But it is unnecessary register update and
should be removed.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
inserts a wait time before reading the conversion register if the
configuration is changed from a previous request.
Currently, the wait time is only the period required for a single
conversion that is calculated as the reciprocal of the sampling frequency.
However we also need to wait for the the previous conversion to complete.
Otherwise we probably get the conversion result for the previous
configuration when the sampling frequency is lower.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure. So a positive return value doesn't indicate an
error condition.
However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks. This change fixes the false error detections.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.
This assumption is broken if the device is runtime suspended and entered
a power-down state. The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.
Fix it by adding a flag to detect that condition and insert a necessary
wait time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI enabled platforms do not have a mean of regulators. Instead we use
hard coded voltage value for reference pin. When value is 0 (default) we
fall back to request a regulator.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use AMI306 calibration data for randomness and debugging.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove IRQ active low support for LSM303AGR since the sensor does not
support that capability for data-ready line
Fixes: a9fd053b56 (iio: st_sensors: support active-low interrupts)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.
The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
auto-suspend for 3 seconds.
This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks
If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.
To avoid this:
- Remove the check to match user requested state, this will cause a
brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
of sensors, like after user finished raw read or buffer disable
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix reading trigger mode, when other bit-fields are set. SMCR register
value must be masked to read SMS (slave mode selection) only.
Fixes: 9eba381 ("iio: make stm32 trigger driver use
INDIO_HARDWARE_TRIGGERED mode")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the datasheet, the range of the acceleration is [-10 g, + 10 g],
so the scale factor should be 10 instead of 5.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reading INT_CLEAR has side effects - disallow reading it via debugfs.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mix device-specific data into randomness pool.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for AMI306 magnetometer - very similar to AMI305.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A software trigger such as hrtimer can be used to capture the data
that will be stored in the buffer.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
srf02 added with support for i2c interface
Attributes for setting max range or sensitivity are omitted for the case of
srf02 type sensor, because they are not supported by the hardware.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ultrasonic sensor srf10 is quite similar to srf08 and now also supported by
the driver as device tree compatible string.
It was necessary to prepare the source for supplementary sensors. This is
done by enum srf08_sensor_type.
The most significiant difference between srf08 and srf10 is another range
and values of register gain (in the driver it's call sensitivity).
Therefore the array of it is extended and dependent of the sensor type.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for triggered buffers.
Data format is quite simple:
distance 16 Bit
alignment 48 Bit
timestamp 64 Bit
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added MODULE_DEVICE_TABLE for device tree bindings.
It used to work without it by using the i2c_device_id table, but adding the
table makes everything clear and documented.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS2MDL magnetometer in
st_magn framework
http://www.st.com/resource/en/datasheet/lis2mdl.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Without the triggered buffer code, we get a link error:
drivers/iio/adc/at91-sama5d2_adc.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x938): undefined reference to `devm_iio_triggered_buffer_setup'
This adds a Kconfig 'select' statement like other ADC
drivers have it already.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove int2 configuration parameter for LIS3DH, LSM303DLHC, LSM330D,
LSM330DL, LSM330DLC, LSM303AGR, LIS2DH12 and LNG2DM since these devices
export just int1 as data-ready line
Fixes: 23cde4d65c (iio: Added platform data to select the DRDY pin)
Fixes: dcdb0a78ca (iio: accel: st_accel: add support to lng2dm)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove int2 configuration parameter for LPS22HB and LPS25H since
these devices export just int1 as data-ready line
Fixes: 931878405b (iio:pressure: Add support for LPS25H pressure sensor)
Fixes: e039e2f5b4 (iio:st_pressure:initial lps22hb sensor support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fix following checkpatch warnings in xadc driver
1. prefer 'unsigned int' to bare use of 'unsigned'.
2. else is not generally useful after a break or return.
3. fill all function definition arguments with identifier name
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add output compare trigger sources available on some instances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STM32H7 timer triggers:
- Add new valids_table
- Introduce compatible, with configuration data
- Extend up to 15 timers, available on STM32H7
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the reference HID sensor hub firmware all Named array enums were
0-based. There is no description of the default base of enums in HID
sensor hub specification as logical minimum should have set this base
value.
Every sensor hub implemented enum as 1-based, without explicitly setting
logical minimum to 1, because of the implementation by one of the major
OS vendor. In Linux we used logical minimum to decide the enum base.
Some sensor hub FWs already changed logical minimum from 0 to 1. We hoped
that every other vendor will follow. But that didn't happen and we had to
fix the report header for every sensor hub to change logical minimum to 1
by using .report_fixup() callback. So for every new sensor hub we had to
modify source code by adding this quirk based on the vendor and device id.
This is becoming a maintenance burden.
This patch hardcodes the logical minimum of power and report state
attributes to 1. In this way we can remove the existing quirks and also
we don't have to add more quirks.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
SPI device registered via OF will always match a legacy SPI device ID and
that the MODALIAS reported will always be of the form spi:<device>.
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.
Besides this could change in the future so the correct approach is to
have an OF device ID table if the devices are registered via OF.
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32 ADC allows each channel to be sampled with a different sampling time,
by setting SMPR registers. Basically, value depends on local electrical
properties. Selecting correct value for sampling time highly depends on
analog source impedance. There is a manual that may help in this process:
'How to get the best ADC accuracy in STM32...'
This patch allows to configure minimum sampling time via device tree,
either for:
- all channels at once:
st,min-sample-time-nsecs = <10000>;
- independently for each channel (must match "st,adc-channels" list):
st,adc-channels = <0 1>;
st,min-sample-time-nsecs = <5000 10000>;
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADC clock input is provided to internal prescaler (that decreases its
frequency). It's then used as reference clock for conversions.
- Fix common clock rate used then by stm32-adc sub-devices. Take common
prescaler into account. Currently, rate is used to set "boost" mode.
It may unnecessarily be set. This impacts power consumption.
- Fix ADC max clock rate on STM32H7 (fADC from datasheet). Currently,
prescaler may be set too low. This can result in ADC reference
clock used for conversion to exceed max allowed clock frequency.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Proper support for the INA219 lowered the minimum sampling period from
2*140us to 2*84us. Subtracting 200us later leads to an underflow and
an almost infinite udelay later.
Using a signed int for the sampling period provides sufficient range
(at most 2*8640*1024us), but catches the underflow when comparing with
buffer_us.
Fixes: 18edac2e22 ("iio: adc: Fix integration time/averaging for INA219/220")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to use encoder mode, timers needs to be enabled (e.g. CEN bit)
along with peripheral clock.
Add IIO_CHAN_INFO_ENABLE attribute to handle this.
Also, in triggered mode, CEN bit is set automatically in hardware.
Then clock must be enabled before starting triggered mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 4adec7da05 ("iio: stm32 trigger: Add quadrature encoder device")
This fixes two issues:
- stm32_set_count_direction: to set down direction
- stm32_get_count_direction: to get down direction
IIO core provides/expects value to be an index of iio_enum items array.
This needs to be turned by these routines into TIM_CR1_DIR (e.g. BIT(4))
value.
Also, report error when attempting to write direction, when in encoder
mode: in this case, direction is read only (given by encoder inputs).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 4adec7da05 ("iio: stm32 trigger: Add quadrature encoder device")
IIO core expects zero as return value for write_raw() callback
in case of success.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If the device is not initialized at least once it happens that the humidity
reading is skipped, which means the special value 0x8000 is delivered.
For omitting this case the oversampling of the humidity must be set before
the oversampling of the temperature und pressure is set as written in the
datasheet of the BME280.
Furthermore proper error detection is added in case a skipped value is read
from the device. This is done also for pressure and temperature reading.
Especially it don't make sense to compensate this value and treat it as
regular value.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
-----BEGIN PGP SIGNATURE-----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=imPz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.14 cycle.
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
Move data-ready configuration in hts221_buffer.c since it is only related
to trigger logic
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add open drain support in order to share requested IRQ line between
hts221 device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
This patch enables adc engine at initialization time and waits
for the initial sequence completion before enabling adc channels.
Without this code adc channels are not functional and shows
zeros for all connected channels.
Tested on mellanox msn platform.
v1 -> v2:
Pointed by Rick Altherr:
- Wait init sequence code enabled by bool
from OF match table.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Rick Altherr <raltherr@google.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for active low interrupts (IRQF_TRIGGER_LOW and
IRQF_TRIGGER_FALLING). Configure the device as active high or low
according to the requested irq line.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Configure sensor ODR just in hts221_write_raw() in order to avoid
to set device sample rate multiple times.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
GENMASK(6, 3) in CTRL_REG1 and GENMASK(6, 2) in CTRL_REG2 are marked
reserved. Do not changed the original value (not declared in the
datasheet) during power-down/suspend routines.
Fixes: e4a70e3e7d (iio: humidity: add support to hts221 rh/temp device)
Fixes: b7079eeac5 (iio: humidity: hts221: add power management support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable Block Data Update in hts221_probe() in order to avoid to reconfigure
it every time the sensor is enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bit-shift in hts221_write_with_mask() instead of coding
the shift depth in the configured value. That change will be necessary
to fix an issue in device power-down procedure.
Simplify hts221_avg_list table management
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for CCS811 VOC sensor. This patch adds support
for reading current and voltage across the sensor and TVOC
and equivalent CO2 values.
Scale and offset values have been computed according to datasheet:
- For current: raw value is in microamps
=> 0.001 scale to convert to milliamps
- For voltage: 1.65V = 1023, therefore 1650mV = 1023
=> 1650.0/1023 = 1.612903 scale to convert to millivolts
- For eCO2: raw value range is from 400ppm to 8192ppm.
=> (val - 400) * (100 - 0) / (8192 - 400) + 0 =
(val - 400) * 0.01283367 => offset: -400, scale = 0.012834
to get a percentage value
-For TVOC: raw value range is from 0ppb to 1187ppb.
=> (val - 0) * 100 / (1187 - 0) + 0 = val * 0.0842459 =>
scale = 0.084246 for getting a percentage value
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested. This is not consistent and breaks
reading raw values after a suspend-resume.
This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When adding maps to the list, they were added using list_add, which adds
them in LIFO order. When parsing using iio_channel_get_all(), these
elements are hence returned in reverse order. As a result, the iio_hwmon
mapping maps the first entry to the last channel and so on.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds support for STM32F4 Digital-To-Analog converter.
Add compatible configuration data to handle hfsel (not present
in stm32f4).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix error message, there's no 'st,dac-channel' property, but 'reg'
(see https://lkml.org/lkml/2017/4/3/567).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't populate array startup_lookup on the stack but instead make
it static. Makes the object code smaller.
Before:
text data bss dec hex filename
21754 5440 128 27322 6aba drivers/iio/adc/at91_adc.o
After:
text data bss dec hex filename
21613 5496 128 27237 6a65 drivers/iio/adc/at91_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I noticed in its DSDT that one of my tablets actually is using the GPADC
pin for temperature monitoring.
The whole axp288_adc_set_ts() function is a bit weird, in the past it was
removed because it seems to make no sense, then this was reverted because
of regressions.
So I decided to test the special GPADC pin handling on this tablet.
Conclusion: not only is axp288_adc_set_ts() necessary, we need to sleep a
bit after making the AXP288_ADC_TS_PIN_CTRL changes before sampling the
GPADC, otherwise it will often (about 80% of the time) read 0 instead of
its actual value.
It seems that there is only 1 bias current source and to be able to use it
for the GPIO0 pin in GPADC mode it must be temporarily turned off for the
TS pin, but the datasheet does not mention this.
This commit adds a sleep after disabling the TS pin bias current,
fixing the GPADC more often then not wrongly returning 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to use the standard name convention rename H3LIS331DL_DRIVER_NAME
macro in H3LIS331DL_ACCEL_DEV_NAME
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add H3LIS331DL, LIS331DL and LIS3LV02DL entries in st_accel_id_table
Fixes: 1e52fefc9b (iio: accel: Add support for the h3lis331dl accel)
Fixes: bbf5f037fa (iio: st_accel: support the LIS331DL sensor)
Fixes: 3acddf74f8 (iio: st-sensors: add support for lis3lv02d accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array startup_lookup static rather having it on the
stack saves 69 bytes. Add in missing int specifier to clean up a
checkpatch warning.
Before:
text data bss dec hex filename
10297 2800 128 13225 33a9 drivers/iio/adc/at91-sama5d2_adc.o
After:
text data bss dec hex filename
10140 2888 128 13156 3364 drivers/iio/adc/at91-sama5d2_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array init_data static rather having it on the
stack saves us a couple hundreds of bytes:
Before:
text data bss dec hex filename
3175 848 0 4023 fb7 drivers/iio/accel/da311.o
After:
text data bss dec hex filename
2860 936 0 3796 ed4 drivers/iio/accel/da311.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.
Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].
[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf
Fixes: a775427632 ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa286 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add newlines to the macro definitions and use a more common style.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.
Datasheet:
http://cds.linear.com/docs/en/datasheet/24713fb.pdf
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.
So lets go back to hard coding the values, this reverts
commit fa2849e964 ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.
The exact cause is not fully understood, hence the revert to a known working
state.
Cc: stable@vger.kernel.org
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When initializing interrupts, the devm_request_any_context_irq will
enable them right away. An atomic flag was set in sun4i_irq_init and read
in the interrupt handler to make sure no unwanted interrupts were
handled. If an unwanted interrupt occurred, the handler would disable
the irq and return IRQ_HANDLED. However, at the end of sun4i_irq_init,
the irq would be disabled as well, resulting in an unbalanced enable
(since there are more disables than enables, the code enabling the
interrupt would never be called).
When reading the ADC or the temperature, the respective irq would be
enabled in the read function and disabled in the irq handler. In the
read function, we would wait for a completion (with a timeout) that will
be set in the irq handler. However, if the completion is never set or if
the wait for completion times out, the irq would not be disabled in the
read function resulting in an unbalanced enable once the read function
is called again (since there are 2+ enables for no disable).
Moving disable_irq from the irq handler to the read function get rid of
these two cases of unbalanced enable.
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv drivers
- Minor fixes and cleanups in various drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J5ye
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv
drivers
- Minor fixes and cleanups in various drivers
* tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (22 commits)
hwmon: (aspeed-pwm-tacho) Poll with short sleeps.
hwmon: (aspeed-pwm-tacho) reduce fan_tach period
hwmon: (ibmpowernv) Add current(A) sensor
hwmon: (ibmpowernv) introduce a legacy_compatibles array
hwmon: (pwm-fan) Switch to new atomic PWM API
hwmon: (scpi) Fix the scale of SCP sensor readings
hwmon: (aspeed-pwm-tacho) Enable both edge measurement.
hwmon: (ibmpowernv) Add highest/lowest attributes to sensors
hwmon: (pmbus) move header file out of I2C realm
hwmon: (max6639) move header file out of I2C realm
hwmon: (ltc4245) move header file out of I2C realm
hwmon: (ds620) move header file out of I2C realm
hwmon: (ads1015) move header file out of I2C realm
hwmon: (adt7475) temperature smoothing
hwmon: (adt7475) add high frequency support
hwmon: (adt7475) fan stall prevention
hwmon: (adt7475) replace find_nearest() with find_closest()
hwmon: (pmbus) Add client driver for IR35221
hwmon: (nct6775) Add support for NCT6795D
hwmon: (nct6775) Improve fan detection
...
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Joel Stanley