The only R8A7740 specific #ifdef hindering ARM multiplatform build is left in
sh_eth_rx(): it covers the code shifting Rx buffer descriptor word 0 by 16. Get
rid of the #ifdef by adding 'shift_rd0' field to the 'struct sh_eth_cpu_data',
making the shift dependent on it, and setting it to 1 for the R8A7740 case...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the comment to 'enum TD_STS_BIT', reformat the values, and add a couple of
values missing before (though unused by the driver).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SH7724 'eesipr_value' field initializer includes DMAC_M_RFRMER & DMAC_M_ECI
bits which are already contained in 0x01ff009f -- remove them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'tx_error_check' field of 'struct sh_eth_cpu_data' is write-only, so remove
it along with the DEFAULT_TX_ERROR_CHECK macro.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver hasn't used NAPI so far; implement its support at last...
The patch was tested on Renesas R8A77781 BOCK-W board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_interrupt() uses the same Rx interrupt mask twice to check the interrupt
status register -- #define EESR_RX_CHECK and use it instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The check introduced by:
commit 26a41ae604
Author: stephen hemminger <stephen@networkplumber.org>
Date: Mon Jun 17 12:09:58 2013 -0700
vxlan: only migrate dynamic FDB entries
was not correct because it is checking flag about type of FDB
entry, rather than the state (dynamic versus static). The confusion
arises because vxlan is reusing values from bridge, and bridge is
reusing values from neighbour table, and easy to get lost in translation.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Introduce by commit 0ae99b5fed
(bcm63xx_enet: split DMA channel register accesses)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usb_8dev hardware has problems on some xhci USB hosts. The driver fails to
read the firmware revision in the probe function. This leads to the following
Oops:
[ 3356.635912] kernel BUG at net/core/dev.c:5701!
The driver tries to free the netdev, which has already been registered, without
unregistering it.
This patch fixes the problem by unregistering the netdev in the error path.
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Reviewed-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The change set of 4305b541, "[SK_BUFF]: Convert skb->end to sk_buff_data_t"
converted skb->end from pointer type to sk_buff_data_t.
The pointed value should be accessed via skb_end_pointer().
Since arm arch doesn't define NET_SKBUFF_DATA_USES_OFFSET,
skb->end is effectively pointer. So it doesn't cause a real problem.
But this patch is good for consistency.
Found by inspection. Compile tested only.
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change set of 4305b541 "[SK_BUFF]: Convert skb->end to sk_buff_data_t"
converted skb->end from pointer to sk_buff_data_t.
The pointed value should be accessed via skb_end_pointer().
Since arm or ppc arch doesn't define NET_SKBUFF_DATA_USES_OFFSET,
skb->end is effectively pointer. So it doesn't cause a real problem.
But this patch is good for consistency.
Found by inspection. Compile test only.
Cc: Simon Horman <horms@verge.net.au>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operation to restart autonegotiation via the PHY.
Tested on i.MX28EVK.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alb_set_slave_mac_addr() sets the mac address in alb mode via
dev_set_mac_address(), which might sleep. It's called from
alb_handle_addr_collision_on_attach() in atomic context (under
read_lock(bond->lock)), thus triggering a bug.
Fix this by moving the lock inside alb_handle_addr_collision_on_attach().
v1->v2:
As Nikolay Aleksandrov noticed, we can drop the bond->lock completely.
Also, use bond_slave_has_mac(), when possible.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after priv->cpts got allocated then this pointer should check to determine
if the allocation succeeded or not.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This will probably be the last batch of wireless fixes intended
for 3.10. Many of these are one- or two-liners, and a couple of
others are mostly relocating existing code to avoid races or to
limit the code to effecting specific hardware, etc.
The mac80211 fixes have a couple of exceptions to the above.
Regarding those, Johannes says:
"Following davem's complaint about my patch, here's a new pull request
w/o the patch he was complaining about, but instead with the const
fix rolled into the fix.
I have a fix for radar detection, one for rate control and a workaround
for broken HT APs which is a regression fix because we didn't rely
on them to be correct before."
Johannes also sends some iwlwifi fixes:
"I picked up Nikolay's patch for the chain noise calibration bug
that seems to have been there forever, a fix from Emmanuel for
setting TX flags on BAR frames and a fix of my own to avoid printing
request_module() errors if the kernel isn't even modular. We also
have our own version of Stanislaw's fix for rate control."
Along with those...
Anderson Lizardo fixes a Bluetooth memory corruption bug when an MTU
value is set to too small of a value.
Arend van Spriel sends a revised brcmsmac bug that fixes a regression
caused by a bad return value in an earlier patch. He also sends a
brcmfmac fix to avoid an oops when loading the driver at boot.
Daniel Drake fixes a race condition in btmrvl that causes hangs on
suspend for OLPC hardware.
Johan Hedberg adds a check to avoid sending a
HCI_Delete_Stored_Link_Key command to devices that don't support them,
avoiding some scary looking log spam.
Stanislaw Gruszka gives us a fix for iwlegacy to be able to use rates
higher than 1Mb/s on older wireless networks. He also sends an rt2x00
fix to reinstate older tx power handling behavior for some devices
that didn't work well with the current code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a very simple driver, based on the original vendor
driver that Qualcomm/Atheros published/submitted previously,
but reworked to make the code saner. However, it also lost
a number of features (TSO/GSO, VLAN acceleration and multi-
queue support) in the process, as well as debugging support
features I didn't have any use for. The only thing I left
is checksum offload.
More features can obviously be added, but this seemed like
a good start for having a driver in mainline at all.
Johannes Stezenbach has verified that the driver works on
AR8161, I have a AR8171 myself. The E2200 device ID I found
on github in somebody's repository.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tg3 code assumes the pci_error_handlers to be always called
in sequence. In particular, during ->error_detected(), NAPI is disabled
and the device is shutdown. The device is later reset and NAPI
re-enabled in ->slot_reset() and ->resume().
In EEH, if more than 6 errors are detected in a hour, only
->error_detected() will be called. This will leave the driver in an
inconsistent state as NAPI is disabled but netif_running state is still
true. When the device is later closed, we'll try to disable NAPI again
and it will loop forever.
We fix this by closing the device if we encounter any error conditions
during the normal sequence of the pci_error_handlers.
v2: Remove the changes in tg3_io_resume() based on Benjamin Poirier's
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should call __vlan_hwaccel_put_tag() only if the packet
comes from vlan, otherwise VLAN_TAG_PRESENT will always be
added.
Reported-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_clone fails if out of memory then just skip the fanout.
Problem was introduced in 3.10 with:
commit 6681712d67
Author: David Stevens <dlstevens@us.ibm.com>
Date: Fri Mar 15 04:35:51 2013 +0000
vxlan: generalize forwarding tables
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only migrate dynamic forwarding table entries, don't modify
static entries. If packet received from incorrect source IP address
assume it is an imposter and drop it.
This patch applies only to -net, a different patch would be needed for earlier
kernels since the NTF_SELF flag was introduced with 3.10.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a packet to arrive during vxlan_stop(), and
have a dynamic entry created. Close this by checking if device
is up.
CPU1 CPU2
vxlan_stop
vxlan_flush
hash_lock acquired
vxlan_encap_recv
vxlan_snoop
waiting for hash_lock
hash_lock relased
vxlan_flush done
hash_lock acquired
vxlan_fdb_create
This is a day-one bug in vxlan goes back to 3.7.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you copy some code, you are supposed to read it. If nothing else,
there's a chance to spot and fix an obvious bug instead of sharing it...
X-Song: "I Got It From Agnes", by Tom Lehrer
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Tom Lehrer? You're dating yourself, Al ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to change the link state of VF (vPort)
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM6345 SoC Ethernet. BCM6345
has a slightly different and older DMA engine which requires the
following modifications:
- the width of the DMA channels on BCM6345 is 64 bytes vs 16 bytes,
which means that the helpers enet_dma{c,s} need to account for this
channel width and we can no longer use macros
- BCM6345 DMA engine does not have any internal SRAM for transfering
buffers
- BCM6345 buffer allocation and flow control is not per-channel but
global (done in RSET_ENETDMA)
- the DMA engine bits are right-shifted by 3 compared to other DMA
generations
- the DMA enable/interrupt masks are a little different (we need to
enabled more bits for 6345)
- some register have the same meaning but are offsetted in the ENET_DMAC
space so a lookup table is required to return the proper offset
The MAC itself is identical and requires no modifications to work.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tulip throws an error when dma debugging is enabled, as it doesn't properly
check dma mapping results with dma_mapping_error() durring tx ring refills.
Easy fix, just add it in, and drop the frame if the mapping is bad
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initialization within brcmf_bus_start() fails on steps
before the brcmf_net_attach() the net_device for the primary
interface needs to be freed.
This patch resolves a panic during kernel boot as reported
by Stephen Warren.
ref.: http://mid.gmane.org/51AD1F22.2080004@wwwdotorg.org
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue that the driver increments the "RX length error"
on every buffer in sh_eth_rx() if the R8A7740.
This patch also adds a description about the Receive Frame Status bits.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the SoC specific support is no longer done with help of #ifdef'fery,
we no longer need '__maybe_unused' annotations to sh_eth_select_mii() and
sh_eth_set_duplex()...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems that don't need wake-on-lan may choose to power down the
chip on system standby. Upon resume, the power on causes the boot code
to startup and initialize the hardware. On one new platform, this is
causing the device to go into a bad state due to a race between the
driver and boot code, once every several hundred resumes. The same race
exists on open since we come up from a power on.
This patch adds a wait for boot code signature at the beginning of
tg3_init_hw() which is common to both cases. If there has not been a
power-off or the boot code has already completed, the signature will be
present and poll_fw() returns immediately. Also return immediately if
the device does not have firmware.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First the type of igmp_retrans (which is the actual counter of
igmp_resend parameter) is changed to u8 to be able to store values up
to 255 (as per documentation). There are two races that were hidden
there and which are easy to trigger after the previous fix, the first is
between bond_resend_igmp_join_requests and bond_change_active_slave
where igmp_retrans is set and can be altered by the periodic. The second
race condition is between multiple running instances of the periodic
(upon execution it can be scheduled again for immediate execution which
can cause the counter to go < 0 which in the unsigned case leads to
unnecessary igmp retransmissions).
Since in bond_change_active_slave bond->lock is held for reading and
curr_slave_lock for writing, we use curr_slave_lock for mutual
exclusion. We can't drop them as there're cases where RTNL is not held
when bond_change_active_slave is called. RCU is unlocked in
bond_resend_igmp_join_requests before getting curr_slave_lock since we
don't need it there and it's pointless to delay.
The decrement is moved inside the "if" block because if we decrement
unconditionally there's still a possibility for a race condition although
it is much more difficult to hit (many changes have to happen in
a very short period in order to trigger) which in the case of 3 parallel
running instances of this function and igmp_retrans == 1
(with check bond->igmp_retrans-- > 1) is:
f1 passes, doesn't re-schedule, but decrements - igmp_retrans = 0
f2 then passes, doesn't re-schedule, but decrements - igmp_retrans = 255
f3 does the unnecessary retransmissions.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bond device is supposed to get the first slave's MAC address and
the first enslavement fails then we need to reset the master's MAC
otherwise it will stay the same as the failed slave device. We do it
after err_undo_flags since that is the first place where the MAC can be
changed and we check if it should've been the first slave and if the
bond's MAC was set to it because that err place is used by multiple
locations prior to changing the master's MAC address.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c: In function:
stmmac_xmit drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1902:74:
error: expected ) before __func__
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to set the coherent DMA mask only if dma_set_mask() succeeded, and to
error out if either fails.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When putting vif-s on the rx notify list, calling xenvif_put() must be
deferred until after the removal from the list and the issuing of the
notification, as both operations dereference the pointer.
Changing this got me to notice that the "irq" variable was effectively
unused (and was of too narrow type anyway).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device::dev_id should not be used merely to indicate a VI index,
as it affects the way the local part of IPv6 addresses is normally
generated.
This field was intended for use where multiple devices may share a
single assigned MAC address and need to have different IPv6 addresses.
T4 VIs each have their own MAC address.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EINVAL on illegal flag instead of uninitialized value. This fixes the
kbuild test warning.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit df8ef8f3aa
"macvlan: add FDB bridge ops and macvlan flags"
added a way to control NOPROMISC macvlan flag through netlink.
However, with a non passthrough device we never set promisc on open,
even if NOPROMISC is off. As a result:
If userspace clears NOPROMISC on open, then does not clear it on a
netlink command, promisc counter is not decremented on stop and there
will be no way to clear it once macvlan is detached.
If userspace does not clear NOPROMISC on open, then sets NOPROMISC on a
netlink command, promisc counter will be decremented from 0 and overflow
to fffffffff with no way to clear promisc.
To fix, simply ignore NOPROMISC flag in a netlink command for
non-passthrough devices, same as we do at open/close.
Since we touch this code anyway - check dev_set_promiscuity return code
and pass it to users (though an error here is unlikely).
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This routine doesn't fail since 9fdc6bef (tuntap: dont use a private kmem_cache)
so it makes sense to compact the code a little bit.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TUN_PERSIST flag is not reported at all -- both TUNGETIFF, and sysfs
"flags" attribute skip one. Knowing whether a device is persistent or not
is critical for checkpoint-restore, thus I propose to add the read-only
IFF_PERSIST one for this.
Setting this new IFF_PERSIST is hardly possible, as TUNSETIFF doesn't check
for unknown flags being zero and thus there can be trash.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This pull request is intended for the 3.11 stream...
One big highlight is the cw1200 driver the ST-E CW1100 & CW1200
WLAN chipsets. This one has been lingering for a while, lacking
some review comments. Once started getting pulled into linux-next,
it got a bit more attention and a number of improvements were made
over the initial cut. No doubt there will be more changes ahead,
but I think it is looking alright at this point.
Along with that, there is the usual flurry of updates to the mac80211
core and the iwlwifi, mwifiex, ath9k, rt2x00, wil6210, and other
drivers. A few of the highlights are some rt2x00 refactoring/cleanup
by Gabor Juhos, some rt2800 hardware support enhancements by Stanislaw
Gruszka, some iwlwifi power management updates from Alexander Bondar,
some enhanced bcma SPROM support from Rafał Miłecki, and a variety
of other things here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9f86134155 (sh_eth: remove SH_ETH_HAS_TSU)
removes 'const' from 'sh_eth_netdev_ops' and modifies it in case TSU registers
are present. I've originally suggested to Iwamatsu-san to split this structure
in two instead and afterwards Dave M. suggested doing the same.
Split 'sh_eth_netdev_ops_tsu' from 'sh_eth_netdev_ops', making both 'const', and
assigning 'ndev->detdev_ops' depending on the presence of TSU registers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My change:
commit cee2c7315f
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Oct 5 13:44:09 2012 +0200
rt2800: use BBP_R1 for setting tx power
unfortunately does not work well with RT5390 and RT3290 chips as they
require different temperature compensation TX power settings (TSSI
tuning). Since that commit make wireless connection very unstable on
those chips, restore previous behavior to fix regression. Once we
implement proper TSSI tuning on 5390/3290 we can restore back setting
TX power by BBP_R1 register for those chips.
Reported-and-tested-by: Mike Romberg <mike-romberg@comcast.net>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced by:
commit 6da3b6c48d
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Mar 24 01:45:52 2013 +0100
brcmsmac: remove brcms_bss_cfg->associated
The regression behaviour was described on mailing list.
http://mid.gmane.org/5197DC4F.7030503@broadcom.com:
"On laptop I installed kernel with brcmsmac compiled as
module. It comes up and associates during boot, but after
logging in there is no connectivity. Triggering reassoc
gives connectivity for some time, but after a while (1-2 min)
it stops."
Before the mentioned commit the return value of
the function brcms_c_ps_allowed() was always false,
which is desired behaviour as power-save is not
supported at the moment. Therefor, the function is
changed to just return false instead of simply
reverting the mentioned commit.
Bug: 58471 <https://bugzilla.kernel.org/show_bug.cgi?id=58471>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sergei Shtylyov