sas_discovery_quiesce_io flag is used to control IO start/resume functionality.
IO will be stoped while doing discovery of topology. Once discovery is completed
It will resume IO. Resending patch including James review.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The reason for this change is there is a data corruption when four different
physical memory regions in the 36GB to 37GB region are
accessed. This is only affecting 1078.
The solution is we need to use different addressing when filling in
the scatter gather table for the effected memory regions. So instead
of snooping on all four different memory holes, we treat any physical
addresses in the 36GB address with the same algorithm.
The fix is explained below
1) Ensure that the message frames are NOT located in the trouble
region. There is no remapping available for message frames, they must
be allocated outside the problem region.
2) Ensure that Sense buffers are NOT in the trouble region. There is
no remapping available.
3) Walk through the SGE entries and if any are inside the trouble region
then they need to be remapped as discussed below.
1) Set the Local Address bit in the SGE Flags field.
MPI_SGE_FLAGS_LOCAL_ADDRESS
2) Ensure we are using 64-bit SGEs
3) Set MSb (Bit 63) of the 64-bit address, this will indicate buffer
location is Host Memory.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix bug
the third param in module_param(,,) is perm instead of default value.
we still need to assign default at first. Also, the default is now
zero not one, so fix the parameter text to reflect that.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for MSI enable/disable for different buses FC,SPI,SAS
instead of having single MSI enable/disable feature.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This Patch is submitted to increment the MPI headers used by LSI MPT
fusion drivers to the latest version 01.05.19. Year is changed in
CopyRight.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k1.
[SCSI] qla2xxx: Add ISP81XX support.
[SCSI] qla2xxx: Use proper request/response queues with MQ instantiations.
[SCSI] qla2xxx: Correct MQ-chain information retrieval during a firmware dump.
[SCSI] qla2xxx: Collapse EFT/FCE copy procedures during a firmware dump.
[SCSI] qla2xxx: Don't pollute kernel logs with ZIO/RIO status messages.
[SCSI] qla2xxx: Don't fallback to interrupt-polling during re-initialization with MSI-X enabled.
[SCSI] qla2xxx: Remove support for reading/writing HW-event-log.
[SCSI] cxgb3i: add missing include
[SCSI] scsi_lib: fix DID_RESET status problems
[SCSI] fc transport: restore missing dev_loss_tmo callback to LLDD
[SCSI] aha152x_cs: Fix regression that keeps driver from using shared interrupts
[SCSI] sd: Correctly handle 6-byte commands with DIX
[SCSI] sd: DIF: Fix tagging on platforms with signed char
[SCSI] sd: DIF: Show app tag on error
[SCSI] Fix error handling for DIF/DIX
[SCSI] scsi_lib: don't decrement busy counters when inserting commands
[SCSI] libsas: fix test for negative unsigned and typos
[SCSI] a2091, gvp11: kill warn_unused_result warnings
[SCSI] fusion: Move a dereference below a NULL test
...
Fixed up trivial conflict due to moving the async part of sd_probe
around in the async probes vs using dev_set_name() in naming.
Convert to net_device_ops and internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/).
// <smpl>
@disable is_null@
identifier f;
expression E;
identifier fld;
statement S;
@@
+ if (E == NULL) S
f(...,E->fld,...);
- if (E == NULL) S
@@
identifier f;
expression E;
identifier fld;
statement S;
@@
+ if (!E) S
f(...,E->fld,...);
- if (!E) S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove excess kernel-doc function parameter notation:
Warning(drivers/message/fusion/mptbase.c:964): Excess function parameter or struct member 'handle' description in 'mpt_free_msg_frame'
Warning(drivers/message/fusion/mptbase.c:5434): Excess function parameter or struct member 'portnum' description in 'mpt_findImVolumes'
Warning(drivers/message/fusion/mptbase.c:6949): Excess function parameter or struct member 'mr' description in 'mpt_spi_log_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Eric.Moore@lsi.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
A bug in the fusion driver was exposed by the switch to block timeout.
Basically, drivers are supposed to terminate commands once error
handling begins on them. The fusion apparently wasn't doing this.
Under the old timeout regime, completions on terminated commands would
by and large get ignored because of the way command timeouts used to
work. The new block timers are very intolerant to this, though,
becuase the request gets cleaned and freed.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=12195
Reported-by: Alex Shi <alex.shi@intel.com>
Tested-by: Ming Lin <ming.m.lin@intel.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This triggers false bug reports as it does a bogus kmalloc with locks held
but is never really compiled into the kernel.
Closes#8329
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make SPI timeout 10s the same as SAS
Signed-off-by: Bernd Schubert <bs@q-leap.de>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (59 commits)
[SCSI] replace __FUNCTION__ with __func__
[SCSI] extend the last_sector_bug flag to cover more sectors
[SCSI] qla2xxx: Update version number to 8.02.01-k6.
[SCSI] qla2xxx: Additional NPIV corrections.
[SCSI] qla2xxx: suppress uninitialized-var warning
[SCSI] qla2xxx: use memory_read_from_buffer()
[SCSI] qla2xxx: Issue proper ISP callbacks during stop-firmware.
[SCSI] ch: fix ch_remove oops
[SCSI] 3w-9xxx: add MSI support and misc fixes
[SCSI] scsi_lib: use blk_rq_tagged in scsi_request_fn
[SCSI] ibmvfc: Update driver version to 1.0.1
[SCSI] ibmvfc: Add ADISC support
[SCSI] ibmvfc: Miscellaneous fixes
[SCSI] ibmvfc: Fix hang on module removal
[SCSI] ibmvfc: Target refcounting fixes
[SCSI] ibmvfc: Reduce unnecessary log noise
[SCSI] sym53c8xx: free luntbl in sym_hcb_free
[SCSI] scsi_scan.c: Release mutex in error handling code
[SCSI] scsi_eh_prep_cmnd should save scmd->underflow
[SCSI] sd: Support for SCSI disk (SBC) Data Integrity Field
...
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
When the firmware is in Fault state it will be identifed only when the next time
the driver access the IOC state.
This patch includes a polling function in the driver which will be executed in
regular interval to check the status of the firmware and if it is in Fault
state, then the firmware will be reset by the driver.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The initial period is set to 0xFF
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a fault on the FC controllers that makes them not respond
correctly to MSI. The SPI controllers are fine, but are likely to be
onboard on older motherboards which don't handle MSI correctly, so
default both these cases to disabled. Enable by setting the module
parameter mpt_msi_enable=1.
For the SAS case, enable MSI by default, but it can be disabled by
setting the module parameter mpt_msi_enable=0.
Cc: "Prakash, Sathya" <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The problem here is that if the ioc faults too early in the bring up
sequence (as it usually does for an irq routing problem), ioc_reset gets
called before the scsi host is even allocated. This causes an oops when
it later schedules a renegotiation. Fix this by checking ioc->sh before
trying to renegotiate.
Cc: "Moore, Eric" <Eric.Moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Updating copyright statement to include the year 2008
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Updating driver version to 3.04.07 from 3.04.06
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global struct mpt_proc_root_dir static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following a hard reset of a SAS raid, one of the raid targets is occasionally
missing. I tracked this down to a pretty obscure little bug.
The LSI fusion drivers for SAS and Fibre Channel both use their respective
transport layers. Those transport layers increment the target number
assigned to new targets.
The routine __scsi_scan_target uses the "this_id" element of the Scsi_Host
structure to avoid scanning the scsi host adapter. Both fusion drivers set
"this_id" from a value returned in a firmware PortFacts response. For my
particular test case (SAS) the firmware id assigned to the initiator was
173. After enough raid resets to cause the raid targets to go and come a
sufficient number of times, the id assigned by the transport to a raid
target would match the id assigned by the host adapter to the "this_id"
field, resulting in that target not being scanned.
Fix by not assigning this_id and not checking it in slave_configure.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a problem with the combination of the upstream power
management fixes and the enabling of MSI by default in that the
suspend path still uses the global variable. Convert it to check
ioc->msi_enable.
Cc: "Moore, Eric" <Eric.Moore@lsi.com>
Cc: "Prakash, Sathya" <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While performing hardware raid reset testing via the raid's client, I
noticed that sometimes, following the reset, that there would be more
raid targets in the lsscsi output than there actually were raid
targets. I tracked this down to the following issue.
Fusion cannot always find the mptsas_portinfo structure for the hba
because it uses the handle stored in ioc->handle to locate it. The
problem is that the firmware can change the handle associated with the
hba when h/w raid is reset (via the raid client). When this happens,
the driver will allocate another mptsas_portinfo structure and link it
into the chain of said structures. This ultimately causes confusion
within the driver resulting in targets not being removed when they
should be.
Eric Moore pointed out that the hba's portinfo structure is always the
first structure on the sas_topology list. This patch modifies
mptsas.c to access the hba's portinfo structure by taking the first
structure on said list.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the semaphore inactive_list_mutex is used as a mutex, convert it to
the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the driver to enable MSI by default for all SAS chips.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The system power state changes like hibernation and standby are not happening
properly with 106XE controllers, this patch modifies the driver to free
resources and allocate resources in power management entry points
[jejb: compile fixes for upstream]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Don't oops if NumPhys==0, instead return -ENODEV.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=9909
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix docbook problems in fusion source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ioc->name is used in the printk's after ioc has been freed. Free
after prinks to fix this.
This patch fixes two use-after-free's introduced by
commit e78d5b8f1e and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Verified all the arches necessary select the CONFIG_64BIT symbol. This
also kills the warning (since it was using the 32-bit case) on parisc64
and mips64.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the I/O resource allocation behavior of FUSION
driver. The current version of driver allocates the I/O resources
even if they are not required and this creates trouble in low resource
environments. This driver now uses
pci_enable_device_mem/pci_enable_device functions to differentiate the
resource allocations.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch sets the IOC pointer in drvrdata of pcidev before adding
the IOC into the list of IOCs. Without this patch the driver oops when
the mptsas and mptctl modules are loaded in parallel.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the module unload problem in flash less 1030
controller environment where firmware download boot functionality is
invoked. The problem is due to the firmware download is being done in
the reverse order, which this patch solves by insureing the download
occurs to the last controller being reset.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes mptsas_smp_handler to update both din_resid or
dout_resid on success. bsg can report back the residual.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix kernel-api docbook warnings.
Warning(linux-2.6.23-git8//drivers/message/fusion/mptscsih.c:2618): No description found for parameter 'sc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/message/fusion/mptctl.c: In function ‘mptctl_mpt_command’:
drivers/message/fusion/mptctl.c:1764: warning: ‘bufIn.len’ may be used uninitialized in this function
drivers/message/fusion/mptctl.c:1765: warning: ‘bufOut.len’ may be used uninitialized in this function
come because gcc gets confused by some "goto" statements in above
function. The warnings have been verified to be bogus, however, the
function does initialize these later (after the offending goto's) in
the function anyway. So let's move those initializations to top of
function, thereby also shutting up these warnings.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NB = number of blocks. This represents the number of blocks to
transfer. The block size is based on the message frame size provided
in the ioc_facts. A value of zero indicates the entire message frame
should be copied. This is two bit value. So by setting this to
non-zero vaule, you increase performance by reducing amount of data
needing to be dma'd. The value that is stored in ioc->ReqeustNB is
sometimes a non-zero vaule, which creates a bug in mptlan, where not
the entire message frame is getting transfer to firware, resulting in
corruption. This fix sets the default to zero, thus entire message
frame is copied.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up prints that use the xxx_printk API, in that the fusion
preamble "mptbase: iocX" follows the info provided by the print API.
The way its currently coded, the [H:C:T] print in sdev_printk will be
inbetween "mptbase" and "iocX", instead of before.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ScsiLookup is an array of pending scmd pointers that the scsi lld
maintains. This array is touched from queuecommand, eh threads, and
interrupt context. This array should put under locks, hence this patch
to synchronize its access. I've added some nice little function
wrappers for this, and moved the ScsiLookup array over to MPT_ADAPTER
struct.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
List below is output from C=2 sparse compilation, which are fixed with
this patch.
1) mptspi: pg0 is defined in x86 version of include/asm/pgtable.h
2) mptsas: context imbalance in 'mptsas_probe' different lock contexts
for basic block
3) mptbase: from mpt_attach - cast adds address space to expression
4) mptbase: from mpt_do_upload - request[] is bad constant expression
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is currently typecasting to obtain the shost hostdata. The
driver is updated to use the shost_priv macro.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding 949X, 949E, and 1078 to Kconfig. Adding "depends on FUSION"
required in the FUSION_LOGGING section, and fixing a spelling error.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some other vender has concerns over this copyright, and Dell has
approved removing it.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up code by accesing the ioc pointer directly instead of via hd->ioc. In the future, most data members of struct MPT_SCSI_HOST will be either deleted or moved to struct MPT_ADAPTER.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
common naming of vdevice through out driver
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
cleaning up some white space that was introduce in a recent "cb_idx int to u8" patch.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Standardize all prints using common MYIOC_s_XXX_FMT macro defined in mptbase.h. Currently the driver uses several different methods to display info, where in some cases the "controller name" generating the printk is not provided.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
alloc_fcdev() calls alloc_netdev() which uses kzalloc to alloc all the
memory together with dev->priv region hence no zeroing of structs inside
struct mpt_lan_priv needed.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker spotted two potential memory leaks in
drivers/message/fusion/mptbase.c::mpt_attach().
There are two returns that may leak the storage allocated for 'ioc'
(sizeof(MPT_ADAPTER) bytes).
A simple fix would be to simply add two kfree() calls before the return
statements, but a better fix (that this patch implements) is to reorder the
code so that if we hit the first return condition we don't have to do the
allocation at all and then just add a kfree() call for the second case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recently LSI Logic Corp was renamed as LSI Corp, so whereever there is
a reference of LSI Logic, it is changed to LSI in mpt fusion driver
code.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When there is state change in FC links, a message is displayed with
old and new link speed.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The data structure definitions from mptsas.c are moved to a new header
file mptsas.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The call back index requires only u8 but in lot of places it is
referred as int, now everywhere the call back index variables are
declared as u8 with uniform name cb_idx
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added support for sending the task management requests through High priority
request FIFO instead of Doorbell writes when firmware support High priority
FIFO.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Per request from Matthew Wilcox - using PCI_VENDOR_ATTO.
Add support for ATTO UL4D, they are rebranded 53C1030.
The changes are
1. Adding a new PCI vendor ID in pci table
2. The spi_port_page_2 is in different format than that of LSI generic
spi_port_page_2 and hence mapping code is added.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for SAS Management Protocol (SMP) passthrough
support via bsg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wire up the mpt_debug_level module parameter so you can write to the
/sys/module/mptbase/parameters/mpt_debug_level and have it take effect
in every ioc.
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptctl.c to support logging in MPT fusion drivers
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptfc.c, mptlan.c, mptsas.c and mptspi.c to
support logging in MPT fusion drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptscsih.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new sysfs attribute is added to retrieve and modify the debug level.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptbase.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new module parameter mpt_debug_level is added to pass the debug level as
module parameter.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a new file mptdebug.h in the fusion source directory,
which contains different debug macros. The existing debug macros and
flags are removed from the mptbase.h and Makefile In Kconfig a new
configuration parameter FUSION_LOGGING is added to enable/disable the
logging support during compile time.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update help in Kconfig for mptfc driver to indicate the driver supports
Brocade FC 4G HBA.
signed-off-by: Gwendal Grignou <ggrignou@brocade.com>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for Brocade 410/420 4Gbit FC HBAs.
They are re-branded LSI HBAs [LSI7104EP-LC/LSI7204EP-LC]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The mptspi and mptsas drivers are modified to deregister from transport layer
if registration with PCI driver failed
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New sysfs scsi_host attributes are added to provide information about Firmware
version, BIOS version, MPI version and other product related information
signed-off-by: Sathya Praksh <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
If there is IO going to the volume while a hidden disk is being torn down,
there is a case where we would return a DID_NO_CONNECT for IO sent to the
volume. The end result is the volume goes read-only. This problem is due to the
fact the firmware mapped target ids saved in per device object is phys_disk_num
for hidden raid components, and target_id for the volume. There is a single
case when both phys_disk_num and target_id are equal, so enters this issue. We
fix this issue by checking the tflags when the device is torned down,
insuring the IO being completed is meant for hidden raid component, not the
volume. In addition to this fix, there are a couple other cases to address
hidden raid components. For instance task_abort and device reset are not
supported by mpt fw for hidden raid components, a bus reset would be required
or target reset to volume.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
nice cosmetic cleaning of eh thread callback funtions
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
rewrite of mpt_fc_log_info to use the enum/defines from mpi_log_fc.h
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update assocated fusion sources with new support email address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch for: http://bugzilla.kernel.org/show_bug.cgi?id=8426
A recent code cleanup that moved code from mptscsih to mptspi
inadvertently change the order some code was called. This caused
a massive slowdown (of 150x to 300x) on the CD/DVD drive on the
high-end HP Integrity servers.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
TODO: use scsi_for_each_sg().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are several cases where the fusion driver uses the logical || to
try to do an arithmetical or ... fix by replacing with |.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Refine some depends statements to limit their visibility to the
environments that are actually supported.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
After host reset, the device are programmed to default asyn narrow nego.
We need to reprogram the parameter back to previous values. If the host
reset is called as a result of spi_dv_device() commands timing out, its
possible to get into an infinite loop of dv to host reset. This will
prevent that case, as we merely program old values. If host reset is
called outside context of domain validation, then we can call
spi_dv_device.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This address the issue of VMWare guest OS being remounted as read-only
becuase the underlying device was held busy too long and at the
same time address Engenio MPP driver concerns over infinite retries.
This patch removes the code that snoops the SAM STATUS on busy, which
would be returning DID_BUS_BUSY, instead we return the status as is.
Retry hanlding seems to be properly handled in scsi_softirq_done,
where a busy sam status would only occurr for the time specified by
(cmd->allowed +1) * cmd->timeout_per_command.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Honour the return value of pci_enable_device(), which
seems to be a desirable thing to do:
2.6.20-rc4
gcc (GCC) 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)
CC [M] drivers/message/fusion/mptbase.o
drivers/message/fusion/mptbase.c: In function `mpt_resume':
drivers/message/fusion/mptbase.c:1541: warning: ignoring return value
of `pci_enable_device', declared with attribute warn_unused_result
It also in turn has mptscsih_resume() honour the return value of
mpt_resume()
I'm not sure about the handling of the other potential error cases
in mpt_resume(), of which there appear to be many. But this does
seem to be a good start.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It seems that most of the code in mptscsih_resume() doesn't
do anything. This patch removes that code.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fix's an oops during driver load time. mptsas_probe calls
mpt_attach(over in mptbase.c). Inside that call, we read some
manufacturing config pages to setup some defaults. While reading the
config pages, the firmware doesn't complete the reply in time, and we
have a timeout. The timeout results in hardreset handler being called.
The hardreset handler calls all the fusion upper layer driver reset
callback handlers. The mptsas_ioc_reset function is the callback
handler in mptsas.c. So where I'm getting to, is mptsas_ioc_reset is
getting called before scsi_host_alloc is called, and the pointer ioc->sh
is NULL as well as the hostdata.
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bump version, and fix email addr for lsi support
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
misc error handling bug fix's
- properly interpret iocstatus returned after task management request
- clear tmState after a failed doorbell
- cleanup mptscsih_taskmgmt_complete
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return proper sas address to sas transport layer for parent phys that
form a wide port. Current implementation returns a different address
for each phy, incremented by one from the base address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fusion firmware requires target reset following hotplug removal event,
with purpose to flush target outstanding request in fw. Current implementation
does the target resets from delayed work tasks, that in heavy load
conditions, take too long to be invoked, resulting in command time outs
This patch will issue target reset immediately from ISR context, and will
queue remaining target resets to be issued after the previous one completes.
The delayed work tasks are spawned during the target reset completion.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
inactive raid support, e.g. exposing hidden raid components
belonging to a volume that are inactive. Also misc bug fix's for
various raid asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
various string updates for iocstatus, logingo, and fw asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move some functions that only apply to the mptspi module over from mptscsih.c
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for greater than 255 target and luns.
Kill the hd->Target[] field, and change all references
of bus_id/target_id, to channel/id.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here are the lastest mpi headers for mpt fusion driver, which defines
the firmware to driver interface.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes the mptctl pass through available if
the mptsas driver is selected. Without this patch
if mptsas is the only fusion driver chosen, then
the mptctl is not presented as an option.
smp_utils uses the mptctl driver to pass SAS SMP
functions through a MPT SAS HBA.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Add modinfo driver version support.
* Change copyright year to 2007.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Endian fix's for warnings found in ppc environment.
* Fix compile time warning when calling scsi_device_reprobe, where
in newer kernels this API expects its return value to be examined.
* Fix compile errors when debug messages are enabled.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A repost of a patch forwarded by Mikael Reed from 2006-12-20.
The fibre channel IOC may kill a request for a variety of
reasons, some of which may be recovered by a retry, some of
which are unlikely to be recovered. Return DID_ERROR
instead of DID_RESET to permit retry of the command,
just not an infinite number of them.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Thanks to James Smart for the inspiration.
Stall error handler if attempting recovery while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Also verify that VirtDevice is available before issuing scsi command.
VirtDevice is removed when fc transport removes a target.
See James Smart's patch of 08/17/2006 for greater detail.
http://marc.theaimsgroup.com/?l=linux-scsi&m=115583213624803&w=2
Also bump version number per Eric's request.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Eric Moore <eric.moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This flag denotes local attachment of the phy. There are two problems
with it:
1) It's actually redundant ... you can get the same information simply
by seeing whether a host is the phys parent
2) we condition a lot of phy parameters on it on the false assumption
that we can only control local phys. I'm wiring up phy resets in the
aic94xx now, and it will be able to reset non-local phys as well.
I fixed 2) by moving the local check into the reset and stats function
of the mptsas, since that seems to be the only HBA that can't
(currently) control non-local phys.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add host_supported_speeds, host_maxframe_size, host_speed, host_fabric_name,
host_port_type, host_port_state, and host_symbolic_name transport attributes
to fusion fibre channel.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch corrects a problem in mptfc which can result in targets
being removed after executing an "lsiutil 99" reset of the fibre
channel ports.
The last rescan event was being processed before the setup reset work
due to an inappropriate optimization in the event processing logic.
Every rescan event is now queued for execution and the setup reset
work now executes in the proper sequence.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based upon a conversation I had with LSI's fibre channel firmware guru,
this patch adds another condition under which the driver waits for the
firmware link initialization / target discovery to complete.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This takes advantage of the sas class backlink function to show which
port on an expander is used to communicate with the parent.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix's to insure download boot could occur when
either channel of 1030 is reset. Necessary in order
for onboard controller in flashless environment
to become operational.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix's to insure proper status is returned to midlayer
when a task abort failed to be aborted by controller
firmware.
Also sanity checks to prevent scsi cmd from being
double completed during error recovery.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas nexus loss support for systems that suport failover.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic for when mptctl is loading at the same time
when one of the fusion llds (mptsas/mptfc/mptspi) is loading.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding support for sas enclosures with smart drives.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Using the port_id for the channel is completely unnecessary since the
host_id/target_id are constructed to be globally unique. Also move
the mptsas driver on to virtual channel 1 for its raid devices.
Acked-by: "Moore, Eric" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This allows us to be rid of the machinery in mptsas for creating and
tracking port numbers. Since mptsas is merely inventing the numbers,
the SAS transport class may as well do it instead.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the current problems the mptsas driver has is that of "ghost"
devices (these are devices the firmware reports as existing, but what
they actually represent are the parents of a lower device), so for
example in my dual expander configuration, three expanders actually show
up, two for the real expanders but a third is created because the
firmware reports that the lower expander also has another expander
connected (which is simply the port going back to the upper expander).
The attached patch eliminates all these ghosts by not allocating any
devices for them if the SAS address is the SAS address of the parent.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The way mpt_interrupt() was coded, it was impossible for the unhandled
interrupt detection logic to ever trigger. All interrupt handlers should
return IRQ_NONE when they have nothing to do.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/aacraid/comminit.c
Fixed up by removing the now renamed CONFIG_IOMMU option from
aacraid
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Adding 1078 ROC (Raid On Chip) Support - New host adapter
* Moving all PCI Vendor/Device ids to using internal defines; a request
from Christoph/James B. some time ago for when the next chip was added.
* Removing SAS 1066/1066E Vendor/Device IDs, as there are no plans to
manufacture that controller.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Wide port support added - using James Bottomley's new SAS wide port API.
(There is a known problem in sas transport layer reported yesterday to
James. The Kobject dev.bus_ids for end devices are not unique across
expanders. I have added a work around in this patch, where I asigning
an unique port identifier for every port within the host - this solves
the problem, but I expect a fix from James in the sas transport).
* Adding target_alloc and target_destroy entry points, and moving code over
from the slave entry points.
* The renaming of some mptscsih_xxx functions declared in mptsas.c,
to mptsas_xxx.
* Target Reset moved from slave_destroy to hotplug work thread
handling (with regard to device removal). Also inhibit IO to end device
while device is being broken down . Talked to James Smart about this
at Linux Expo (with questions of how the fc transport handles this).
* Cleaning up the kzalloc's, and kfree's
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump driver version number to reflect addition of various
fibre channel patches.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver uses msleep_interruptible() in the code path responsible
for resetting the card's ports via the lsiutil command. If a
<ctrl-c> is received during the reset it can leave a port in such
a state that the only way to regain its use is to reboot the system.
Changing from msleep_interruptible() to msleep() corrects the problem.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While doing board reset testing I was able to put the system in
an infinite request/response loop between the scsi layer and
mptscsih_qcmd() by aborting the reset. This patch installs
a "SETUP RESET" handler which calls fc_remote_port_delete()
for all registered rports. This blocks the target which
prevents the loop. Additionally, should the reset fail to
complete, the transport will now terminate i/o to the target.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The fibre channel firmware provides a timer which is similar in purpose
to the fibre channel transport's device loss timer. The effect of this
timer is to extend the total time that a target will be missing beyond
the value associated with the transport's timer. This patch changes
the firmware timer to a default of one second which significantly reduces
the lag between when a target goes missing and the notification of the
fibre channel transport.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move fibre channel event and reset handling to mptfc. This will
result in fewer changes over time that need to be applied to
either mptbase.c or mptscsih.c.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
MPT fusion driver initialization fails while second kernel is booting,
after a system crash (if kdump kernel is configured). Oops message is
pasted below.
*****************************************************************************
Fusion MPT base driver 3.03.08
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SAS Host driver 3.03.08 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
mptbase: Initiating ioc0 bringup
BUG: unable to handle kernel paging request at virtual address 00002608
printing eip:
c11782fd
*pde = 00000000
Oops: 0000 [#1]
Modules linked in:
CPU: 0
EIP: 0060:[<c11782fd>] Not tainted VLI
EFLAGS: 00010046 (2.6.17-rc1-16M #2)
EIP is at mptscsih_io_done+0x27/0x3a3
eax: c4fed000 ebx: c4fed000 ecx: 00002600 edx: 00000298
esi: c11782d6 edi: 00002600 ebp: 00000000 esp: c1332f74
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c1332000 task=c128f9c0) Stack: <0>0000006c 00000020 00000298 00002600 c4fed000 c4fed000 c11782d6 0000260 0
00000000 c1172c49 c4fed000 c1305b40 00000005 00000000 c1172d75 c48877e0
c1029687 00000000 c1307fb8 00000000 c1305a00 00000001 00000000 c1307fb8
Call Trace:
<c11782d6> mptscsih_io_done+0x0/0x3a3 <c1172c49> mpt_turbo_reply+0xbb/0xd3
<c1172d75> mpt_interrupt+0x22/0x2b <c1029687> misrouted_irq+0x63/0xcb
<c10297b3> note_interrupt+0x43/0x98 <c10292f9> __do_IRQ+0x68/0x8f
<c1003fac> do_IRQ+0x36/0x4e
=======================
<c1002aa6> common_interrupt+0x1a/0x20 <c1001150> mwait_idle+0x1a/0x2a
<c10010bf> cpu_idle+0x40/0x5c <c1308610> start_kernel+0x17a/0x17c Code: 5e 5f 5d c3 55 89 cd 57 56 53 83 ec 14 89 54 24 0c 89 44 24 10 8b 90 cc 00 00 00 8b 4c 24 0c 81 c2 98 02 00 00 85 ed 89 54 24 08 <0f> b7 79 08 89 fe 74 04 0f b7 75 08 66 39 f7 75 0d 8b 44 24 0c
*******************************************************************************
o Kdump capture kernel boot fails during initialization of MPT fusion driver.
(LSI Logic / Symbios Logic SAS1064E PCI-Express Fusion-MPT SAS (rev 01))
o Problem is easily reproducible, if system crashed while some disk activity
like cp operation was going on.
o After a system crash, devices are not shutdown and capture kernel starts
booting while skipping BIOS. Hence underlying device is left in operational
state. In this case scsi contoller was left with interrupt line asserted
reply FIFO was not empty. When driver starts initializing in the second
kernel, it receives the interrupt the moment request_irq() is called.
Interrupt handler, reads the message from reply FIFO and tries to access
the associated message frame and panics, as in the new kernel's context
that message frame is not valid at all.
o In this scenario, probably we should delay the request_irq() call. First
bring up the IOC, reset it if needed and then should register for irq.
o I have tested the patch with SAS1064E and 53c1030 controllers.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All registered reset callback handlers are called during reset processing.
The mptspi modules has its own reset callback handler, just recently
added for issuing domain validation after host reset. If either the mptsas or
mptfc driver are loaded, this callback could be called. Thus resulting
in domain validation being issued for sas or fibre end devices.
Fix this by having mptbase.c check the bus type against the driver
type and only call the reset handler if they match (or if it's a
non-bus specific reset handler).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A race condition exists in mptfc between the thread registering a device
with the fc transport and the scan work generated by the transport.
This race existed prior to the application of the mptfc bug fix patch.
mptfc_register_dev() calls fc_remote_port_add() with the FC_RPORT_ROLE_TARGET
bit set in the rport ids passed to the function. Having this bit set causes
fc_remote_port_add() to schedule a scan of the device.
This scan can execute before mptfc_register_dev() can fill in the dd_data
in the rport structure. When this happens, mptfc_target_alloc() will fail
because dd_data is null.
Attached is a patch which fixes the problem. The patch changes the rport ids
passed to fc_remote_port_add() to not have the TARGET bit set. This prevents
the scan from being scheduled. After mptfc_register_dev() fills in the rport
dd_data field, fc_remote_port_rolechg() is called, changing the role of the
rport to TARGET. Thus, the scan is scheduled after dd_data is filled
in which prevents the failure in mptfc_target_alloc().
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a bug fix for mptspi driver, where after a host reset or
resume, we revalidate the negotiation parameters for all devices.
This bug was introduced when the driver was ported to use the spi
transport layer.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fix for stack overflow in EventDescriptionStr, (a function
for debuging firmware events). We allocated 50 bytes on local stack
for buff[], however there are places in the code where we've attempted
copying in greater than 50 bytes into buff[].
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mptbase.h
bump version number to 3.03.09
remove unneeded flags
define workq and remove old fc specific locks
mptbase.c
initialize new lock and don't initialize two removed locks
mptscsih.c
when firmware reports target is no longer there, return
DID_REQUEUE for fc hosts so that i/o doesn't get killed until
the transport has an opportunity to manage the loss via its
dev loss timer
when the "eh_abort" routine is called, check to see if the
driver has the command or not before looking to see if a reset
is pending. James Smart and I talked about this and believe
that the API for this routine is: if driver doesn't have
command, return SUCCESS. This change helps prevent a target
from being taken offline. SUCCESS is returned because it's
likely that the command completed after error recovery timed
it out but before it could be aborted.
provide a routine to queue work to newly created workq, and
use it.
remove "ioc" from mptscsih_abort() it was only used one time.
the other references were via hd->ioc, so I just moved it....
net change in references to ioc via hd->ioc is zero
move hd->resetPending test and hd->timeouts increment to after
the test for whether the command to be aborted remains known
to the driver
Make certain that the workq exists before queuing work to it.
mptfc.c
no longer need to lock rport data structures as I was able to
single thread the code! I fixed up the debug code to
eliminate compilation messages due to type mismatch in the
printk. Got rid of some no longer needed rport flags.
Initialize and destroy the workq used for the rescan work.
simplify the logic regarding the increment of
fc_rescan_work_count. use post increment and test for zero
vs. pre increment and test for one; eliminate work_count
variable: queue_work can be called with the work_lock held as
it doesn't sleep
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch handles case where raid hidden components
are not being removed when power turned off to device
attached to expander, as well as the case of
exposing raid components when power is turned back on
to devices attached to an expander. (This is a repost
of this patch, with mptsas_is_end_device declared
further up in the code.)
This patch contains some other miscellaneous bug fix's.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Driver panic when RAID logical volume was present when driver
loaded, or when a RAID logical volume was created on the fly.
This issue was created in due to recent scsi_transport_sas change,
when sas_read_port_mode_page was added into the mptsas drivers
slave_config entry point.
This new API expects that all sdev's to be assocated to an rphy, however
that is not the case for logical volumes, as they are created using
scsi_add_device, instead of sas_rphy_add().
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The conversion of mptsas should allow the elimination of the contained
flag in the sas transport class.
Acked-by: "Moore, Eric" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds support for hot adding and removing
expanders, and its associated attached devices.
When there is a change in topology,
the fusion firmware sends the
MPI_EVENT_SAS_DISCOVERY event to the driver.
The driver will read firmware config pages
to determine what changes took place, and refresh
drivers view of the world stored in ioc->sas_topology.
Here is the details of the action the driver does:
(1) Expander Added : The mptsas_discovery_work
workqueue is called. Config pages read, and
ioc->sas_topology is refreshed. The sas_phy_add()
is called for each phy of the expander. The
expanders attached devices are added via
sas_rphy_add(). Added end devices are handled within
the MPT_ADD_DEVICE logic in mptsas_hotplug_work
workqueue.
(2) Expander Delete : The sas_rphy_delete() will be
called for the top most compenent of the parent that the
expander is attached to. The sas_rphy_delete call
will delete all the children phys, rphys, and end devices.
This is handled from mptsas_discovery_work workqueue.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Suppport for exposing hidden raid components
for sg interface. The sdev->no_uld_attach flag
will set set accordingly.
The sas module supports adding/removing raid
volumes using online storage management application
interface.
This patch rely's on patch's provided to me
by Christoph Hellwig, that exports device_reprobe.
I will post those patch's on behalf of Christoph.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changelog:
(1) fix memory leak: p->phy_info
(2) initialize device_info and port_info data fields
(3) initialize the hba firmware handle
(4) initialize phy_id for attached phy_info data fields
(5) initialize attached phy_info data fields
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kashyap, Desai