There are special kinds of FW such as WMI only which
are used for testing, diagnostics and other specific
scenario.
Such FW is loaded during driver probe and the driver
disallows enabling any network interface, to avoid
operational issues.
In many cases it is used to debug early versions
of FW with new features, which sometimes fail
on startup.
Currently when such FW fails to load (for example,
because of init failure), the driver probe would fail
and shutdown the device making it difficult to debug
the early failure.
To fix this, ignore load failures in WMI only FW and
allow driver probe to succeed, making it possible to
continue and debug the FW load failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The short frame check in wil_sring_reap_rx_edma uses
skb->len which store the maximum frame length. Fix
this to use dmalen which is the actual length of
the received frame.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
writel_relaxed can be used in wil_debugfs_iomem_x32_set
since there is a wmb call immediately after.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Call cfg80211_inform_bss_frame_data to report cfg80211 on the
boottime_ns in order to prevent the scan results filtering due to
aging.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon driver rmmod, cancel_work_sync() can be invoked on
p2p.discovery_expired_work before this work struct was initialized.
This causes a WARN_ON with newer kernel version.
Add initialization of discovery_expired_work inside wil_vif_init().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cid value is not being verified in wmi_evt_delba(),
verification is added.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to compiler optimization, it's possible that dr_bit (descriptor
ready) is read last from the status message.
Due to race condition between HW writing the status message and
driver reading it, other fields that were read earlier (before dr_bit)
could have invalid values.
Fix this by explicitly reading the dr_bit first and then using rmb
before reading the rest of the status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMC is a hardware debug mechanism which allows capturing real time
debug data and stream it to host memory. The driver allocates memory
buffers and set them inside PMC ring of descriptors.
Add pmcring debugfs that application can use to read the binary
content of descriptors inside the PMC ring (cat pmcring).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move common part of wil_netif_rx_any into new helper function and add
support for non-gro receive using netif_rx_ni.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tlv targets such as WCN3990 send more data in the chan info event, which is
not sent by the non tlv targets. There is a minimum size check in the wmi event
for non-tlv targets and hence we cannot update the common channel info
structure as it was done in commit 13104929d2 ("ath10k: fill the channel
survey results for WCN3990 correctly"). This broke channel survey results on
10.x firmware versions.
If the common channel info structure is updated, the size check for chan info
event for non-tlv targets will fail and return -EPROTO and we see the below
error messages
ath10k_pci 0000:01:00.0: failed to parse chan info event: -71
Add tlv specific channel info structure and restore the original size of the
common channel info structure to mitigate this issue.
Tested HW: WCN3990
QCA9887
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
10.2.4-1.0-00037
Fixes: 13104929d2 ("ath10k: fill the channel survey results for WCN3990 correctly")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b2 ("ath10k: sdio: set skb len for all rx packets")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My wave-1 firmware often crashes when I am bringing down
AP vdevs, and sometimes at least some machines lockup hard
after spewing IOMMU errors.
I don't see the same issue in STA mode, so I suspect beacons
are the issue.
Moving the beacon buf deletion to later in the vdev teardown
logic appears to help this problem. Firmware still crashes
often, but several iterations did not show IOMMU errors and
machine didn't hang.
Tested hardware: QCA9880
Tested firmware: ath10k-ct from beginning of 2019, exact version unknown
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath9k_wmi_cmd, the allocated network buffer needs to be released
if timeout happens. Otherwise memory will be leaked.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service
if time out happens, the allocated buffer needs to be released.
Otherwise there will be memory leak.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_reg_rmw_single do not need return value to cope with different
cases. And change functon return type to void.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, if the rssi is not good, then it have some retry,
firmware will indicate the msdu list of a ppdu with a hole, it
means it lost the hole msdu, after the msdu retry from AP, the
hole msdu will indicate from firmware later. The hole msdu's PN
check will fail and the hole msdu will be dropped.
PN check fail example:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3818 6105 success
3819 6106 success
3820 6107 success
3817 6104 fail
The correct logic is reorder the msdu list and then do PN check.
ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic
and then do PN check in ieee80211_rx_h_decrypt of mac80211.
example after reorder:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3817 6104 success
3818 6105 success
3819 6106 success
3820 6107 success
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PMF case, the action,deauth,disassoc management need to encrypt
by hardware, it need to reserve 8 bytes for encryption, otherwise
the packet will be sent out with error format, then PMF case will
fail.
After add the 8 bytes, it will pass the PMF case.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The `ar_usb` field of `ath6kl_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath6kl_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath6kl_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath6kl_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath6kl_usb_alloc_urb_from_pipe` and
`ath6kl_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref
(CVE-2019-15098).
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clang triggers a warning about oversized stack frames that gcc does not
notice because of slightly different inlining decisions:
ath/wcn36xx/smd.c:1409:5: error: stack frame size of 1040 bytes in function 'wcn36xx_smd_config_bss' [-Werror,-Wframe-larger-than=]
ath/wcn36xx/smd.c:640:5: error: stack frame size of 1032 bytes in function 'wcn36xx_smd_start_hw_scan' [-Werror,-Wframe-larger-than=]
Basically the wcn36xx_hal_start_scan_offload_req_msg,
wcn36xx_hal_config_bss_req_msg_v1, and wcn36xx_hal_config_bss_req_msg
structures are too large to be put on the kernel stack, but small
enough that gcc does not warn about them.
Use kzalloc() to allocate them all. There are similar structures in other
parts of this driver, but they are all smaller, with the next largest
stack frame at 480 bytes for wcn36xx_smd_send_beacon.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath6kl_htc_mbox_create(), when kzalloc() on line 2855 fails,
target->dev is assigned to NULL, and ath6kl_htc_mbox_cleanup(target) is
called on line 2885.
In ath6kl_htc_mbox_cleanup(), target->dev is used on line 2895:
ath6kl_hif_cleanup_scatter(target->dev->ar);
Thus, a null-pointer dereference may occur.
To fix this bug, kfree(target) is called and NULL is returned when
kzalloc() on line 2855 fails.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize acktimeout to the maximum configurable value in
ath_dynack_reset in order to not disconnect long distance static links
enabling dynack and even to take care of possible errors configuring
a static timeout. Moreover initialize station timeout value to the current
acktimeout value
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compute maximum configurable ackimeout/ctstimeout according to channel
width (clockrate)
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add compute timeout to last computation timestamp in
ath_dynack_reset in order to not run ath_dynack_compute_ackto
immediately
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce ath_dynack_set_timeout routine to configure slottime/ack/cts
timeouts and remove duplicated code
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Atheros cards with a AR92XX generation (and older) chip usually
store their pci(e) initialization vectors on an external eeprom chip.
However these chips technically don't need the eeprom chip attached,
the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that
"... if the EEPROM content is not valid, a value of 0xFF1C returns
when read from the register". So, they will show up on the system's
pci bus. However in that state, ath9k can't load, since it relies
on having the correct pci-id, otherwise it doesn't know what chip it
actually is. This happens on many embedded devices like routers
and accesspoint since they want to keep the BOM low and store the
pci(e) initialization vectors together with the calibration data
on the system's FLASH, which is out of reach of the ath9k chip.
Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed
Teleworker Gateway) need to be able to initialize the PCIe wifi device.
Normally, this should be done as a pci quirk during the early stages of
booting linux. However, this isn't possible for devices which have the
init code for the Atheros chip stored on NAND in an UBI volume.
Hence, this module can be used to initialize the chip when the
user-space is ready to extract the init code.
Martin Blumenstingl prodived the following fixes:
owl-loader: add support for OWL emulation PCI devices
owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
owl-loader: use dev_* instead of pr_* logging functions
owl-loader: auto-generate the eeprom filename as fallback
owl-loader: add a debug message when swapping the eeprom data
owl-loader: add missing newlines in log messages
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/carl9170/usb.c: In function carl9170_usb_disconnect:
drivers/net/wireless/ath/carl9170/usb.c:1110:21:
warning: variable udev set but not used [-Wunused-but-set-variable]
It is not use since commit feb09b2933 ("carl9170:
fix misuse of device driver API")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A null pointer would be passed to a call of the function “kfree”
directly after a call of the function “kcalloc” failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11.
wil6210 reports it's EDMG capabilities (that are also based on FW
capability) to cfg80211 by filling
wiphy->bands[NL80211_BAND_60GHZ]->edmg_cap.
wil6210 handles edmg.channels and edmg.bw_config requested in connect
and start_ap operations.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several occasions where a negative cid value is passed
into wil_cid_valid and this is converted into a u8 causing the
range check of cid >= 0 to always succeed. Fix this by making
the cid argument an int to handle any -ve error value of cid.
An example of this behaviour is in wil_cfg80211_dump_station,
where cid is assigned -ENOENT if the call to wil_find_cid_by_idx
fails, and this -ve value is passed to wil_cid_valid. I believe
that the conversion of -ENOENT to the u8 value 254 which is
greater than wil->max_assoc_sta causes wil_find_cid_by_idx to
currently work fine, but I think is by luck and not the
intended behaviour.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Matteo Croce says:
====================
mvpp2: per-cpu buffers
This patchset workarounds an PP2 HW limitation which prevents to use
per-cpu rx buffers.
The first patch is just a refactor to prepare for the second one.
The second one allocates percpu buffers if the following conditions are met:
- CPU number is less or equal 4
- no port is using jumbo frames
If the following conditions are not met at load time, of jumbo frame is enabled
later on, the shared allocation is reverted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).
As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.
This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.
If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.
When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.
Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a function such as dsa_slave_create fails, currently the following
stack trace can be seen:
[ 2.038342] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.054556] sja1105 spi0.1: Reset switch and programmed static config
[ 2.063837] sja1105 spi0.1: Enabled switch tagging
[ 2.068706] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.076371] ------------[ cut here ]------------
[ 2.080973] WARNING: CPU: 1 PID: 21 at net/core/devlink.c:6184 devlink_free+0x1b4/0x1c0
[ 2.088954] Modules linked in:
[ 2.092005] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 5.3.0-rc6-01360-g41b52e38d2b6-dirty #1746
[ 2.100912] Hardware name: Freescale LS1021A
[ 2.105162] Workqueue: events deferred_probe_work_func
[ 2.110287] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 2.117992] [<c030d8cc>] (show_stack) from [<c10b08d8>] (dump_stack+0xb4/0xc8)
[ 2.125180] [<c10b08d8>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 2.132018] [<c0349d04>] (__warn) from [<c0349e34>] (warn_slowpath_null+0x40/0x48)
[ 2.139549] [<c0349e34>] (warn_slowpath_null) from [<c0f19d74>] (devlink_free+0x1b4/0x1c0)
[ 2.147772] [<c0f19d74>] (devlink_free) from [<c1064fc0>] (dsa_switch_teardown+0x60/0x6c)
[ 2.155907] [<c1064fc0>] (dsa_switch_teardown) from [<c1065950>] (dsa_register_switch+0x8e4/0xaa8)
[ 2.164821] [<c1065950>] (dsa_register_switch) from [<c0ba7fe4>] (sja1105_probe+0x21c/0x2ec)
[ 2.173216] [<c0ba7fe4>] (sja1105_probe) from [<c0b35948>] (spi_drv_probe+0x80/0xa4)
[ 2.180920] [<c0b35948>] (spi_drv_probe) from [<c0a4c1cc>] (really_probe+0x108/0x400)
[ 2.188711] [<c0a4c1cc>] (really_probe) from [<c0a4c694>] (driver_probe_device+0x78/0x1bc)
[ 2.196933] [<c0a4c694>] (driver_probe_device) from [<c0a4a3dc>] (bus_for_each_drv+0x58/0xb8)
[ 2.205414] [<c0a4a3dc>] (bus_for_each_drv) from [<c0a4c024>] (__device_attach+0xd0/0x168)
[ 2.213637] [<c0a4c024>] (__device_attach) from [<c0a4b1d0>] (bus_probe_device+0x84/0x8c)
[ 2.221772] [<c0a4b1d0>] (bus_probe_device) from [<c0a4b72c>] (deferred_probe_work_func+0x84/0xc4)
[ 2.230686] [<c0a4b72c>] (deferred_probe_work_func) from [<c03650a4>] (process_one_work+0x218/0x510)
[ 2.239772] [<c03650a4>] (process_one_work) from [<c03660d8>] (worker_thread+0x2a8/0x5c0)
[ 2.247908] [<c03660d8>] (worker_thread) from [<c036b348>] (kthread+0x148/0x150)
[ 2.255265] [<c036b348>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 2.262444] Exception stack(0xea965fb0 to 0xea965ff8)
[ 2.267466] 5fa0: 00000000 00000000 00000000 00000000
[ 2.275598] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.283729] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 2.290333] ---[ end trace ca5d506728a0581a ]---
devlink_free is complaining right here:
WARN_ON(!list_empty(&devlink->port_list));
This happens because devlink_port_unregister is no longer done right
away in dsa_port_setup when a DSA_PORT_TYPE_USER has failed.
Vivien said about this change that:
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
which is not really true. The devlink_port_unregister function _is_
being called unconditionally from within dsa_port_setup, but not for
this port that just failed, just for the previous ones which were set
up.
ports_teardown:
for (i = 0; i < port; i++)
dsa_port_teardown(&ds->ports[i]);
Initially I was tempted to fix this by extending the "for" loop to also
cover the port that failed during setup. But this could have potentially
unforeseen consequences unrelated to devlink_port or even other types of
ports than user ports, which I can't really test for. For example, if
for some reason devlink_port_register itself would fail, then
unconditionally unregistering it in dsa_port_teardown would not be a
smart idea. The list might go on.
So just make dsa_port_setup undo the setup it had done upon failure, and
let the for loop undo the work of setting up the previous ports, which
are guaranteed to be brought up to a consistent state.
Fixes: 955222ca52 ("net: dsa: use a single switch statement for port setup")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take only FIB events that are happening in init_net into account. No other
namespaces are supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some small char and misc driver fixes for reported issues for
5.3-rc7
Also included in here is the documentation for how we are handling
hardware issues under embargo that everyone has finally agreed on, as
well as a MAINTAINERS update for the suckers who agreed to handle the
LICENSES/ files.
All of these have been in linux-next last week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXW02Nw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylCNQCgwWKnuinNXnxCvRJhqINnlBrwb/YAoMEogKuv
olIx01hAZEUNZuAOgAXj
=eXfW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for reported issues for
5.3-rc7
Also included in here is the documentation for how we are handling
hardware issues under embargo that everyone has finally agreed on, as
well as a MAINTAINERS update for the suckers who agreed to handle the
LICENSES/ files.
All of these have been in linux-next last week with no reported
issues"
* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fsi: scom: Don't abort operations for minor errors
vmw_balloon: Fix offline page marking with compaction
VMCI: Release resource if the work is already queued
Documentation/process: Embargoed hardware security issues
lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
mei: me: add Tiger Lake point LP device ID
intel_th: pci: Add Tiger Lake support
intel_th: pci: Add support for another Lewisburg PCH
stm class: Fix a double free of stm_source_device
MAINTAINERS: add entry for LICENSES and SPDX stuff
fpga: altera-ps-spi: Fix getting of optional confd gpio
Here are some small USB fixes that have been in linux-next this past
week for 5.3-rc7
They fix the usual xhci, syzbot reports, and other small issues that
have come up last week.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXW01og8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykncgCfbiiOcrvw+HBhO090Iv090YdNDtgAn1qbzJYF
wz9KyerAwkLKm5V0Muv2
=HPon
-----END PGP SIGNATURE-----
Merge tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes that have been in linux-next this past
week for 5.3-rc7
They fix the usual xhci, syzbot reports, and other small issues that
have come up last week.
All have been in linux-next with no reported issues"
* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-wdm: fix race between write and disconnect due to flag abuse
usb: host: xhci: rcar: Fix typo in compatible string matching
usb: host: xhci-tegra: Set DMA mask correctly
USB: storage: ums-realtek: Whitelist auto-delink support
USB: storage: ums-realtek: Update module parameter description for auto_delink_en
usb: host: ohci: fix a race condition between shutdown and irq
usb: hcd: use managed device resources
typec: tcpm: fix a typo in the comparison of pdo_max_voltage
usb-storage: Add new JMS567 revision to unusual_devs
usb: chipidea: udc: don't do hardware access if gadget has stopped
usbtmc: more sanity checking for packet size
usb: udc: lpc32xx: silence fall-through warning
Pull networking fixes from David Miller:
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: centralize SERDES IRQ handling
Following Marek's work on the abstraction of the SERDES lanes mapping, this
series trades the .serdes_irq_setup and .serdes_irq_free callbacks for new
.serdes_irq_mapping, .serdes_irq_enable and .serdes_irq_status operations.
This has the benefit to limit the various SERDES implementations to simple
register accesses only; centralize the IRQ handling and mutex locking logic;
as well as reducing boilerplate in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352_serdes_power_set helper is only used at one place, in
mv88e6352_serdes_power. Keep it simple and merge the two functions
together.
Use mv88e6xxx_serdes_get_lane instead of mv88e6352_port_has_serdes
to avoid moving code. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.
For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.
This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lior David