In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141432
Addresses-Coverity-ID: 141433
Addresses-Coverity-ID: 141434
Addresses-Coverity-ID: 141435
Addresses-Coverity-ID: 141436
Addresses-Coverity-ID: 1357360
Addresses-Coverity-ID: 1357403
Addresses-Coverity-ID: 1357433
Addresses-Coverity-ID: 1392622
Addresses-Coverity-ID: 1415273
Addresses-Coverity-ID: 1435752
Addresses-Coverity-ID: 1441500
Addresses-Coverity-ID: 1454596
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628223541.GA17665@embeddedor.com
Some MG PLL registers have fields that need to be preserved at their HW
default or BIOS programmed values. So make sure we preserve them.
v2:
- Add comment to icl_mg_pll_write() explaining the need for register
masks. (Vandita)
- Fix patchwork checkpatch warning.
v3:
- Rebase on drm-tip.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v1)
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180619164115.7835-1-imre.deak@intel.com
Atm we're zeroing out fields in MG_PLL_BIAS and MG_PLL_TDC_COLDST_BIAS
if refclk is 38.4MHz, whereas the spec tells us to preserve them.
Although the calculated values mostly match the register defaults even
for the 38.4MHz case, there are some differences wrt. what BIOS
programs (I noticed at least differences in the MG_PLL_BIAS/IREFTRIM and
MG_PLL_BIAS/BIASCAL_EN fields). In the lack of further info on how to
program these fields, just do what the spec says and preserve the BIOS
state.
v2:
- Preserve the BIOS programmed reg fields instead of programming them.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v1)
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615143911.31082-1-imre.deak@intel.com
PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
This gets a little tricky for ICL since there is
no register bit that maps directly to the link clock.
So this patch creates a separate function in intel_dpll_mgr.c
to obtain the write array PLL Params and compares the set
pll_params with the table to get the corresponding link
clock.
v2:
- Fix the encoder type check (DK).
- Improve our error checking, return a sane value (Mika, Paulo).
- Fix table entries (Paulo).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Paulo: implement v2]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523224444.19017-1-paulo.r.zanoni@intel.com
This implements the "MG PLL Programming" sequence from our spec. The
biggest problem was that the spec assumes real numbers, so we had to
adjust some numbers and calculations due to the fact that the Kernel
prefers to deal with integers.
I recommend grabbing some coffee, a pen and paper before reviewing
this patch.
v2:
- Correctly identify DP encoders after upstream change.
- Small checkpatch issues.
- Rebase.
v3:
- Try to impove the comment on the tdc_targetcnt calculation based on
Manasi's feedback (Manasi).
- Rebase.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-7-paulo.r.zanoni@intel.com
HDMI mode DPLL programming on ICL is the same as CNL, so just reuse
the CNL code.
v2:
- Properly detect HDMI crtcs.
- Rebase after changes to the cnl function (clock * 1000).
v3:
- Add a comment to clarify why we treat 38.4 as 19.2 (James).
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-5-paulo.r.zanoni@intel.com
This commit introduces the definitions for the ICL clocks and adds the
basic functions to the shared DPLL framework. It adds code for the
Enable and Disable sequences for some PLLs, but it does not have the
code to compute the actual PLL values, which are marked as TODO
comments and should be introduced as separate commits.
Special thanks to James Ausmus for investigating and fixing a bug with
the placement of icl_unmap_plls_to_ports() function.
v2:
- Rebase around dpll_lock changes.
v3:
- The spec now says what the timeouts should be.
- Touch DPCLKA_CFGCR0_ICL at the appropriate time so we don't freeze
the machine.
- Checkpatch found a white space problem.
- Small adjustments before upstreaming.
v4:
- Move the ICL checks out of the *map_plls_to_ports() functions
(James)
- Add extra encoder check (James)
- Call icl_unmap_plls_to_ports() later (James)
v5:
- Rebase after the pll struct changes.
v6:
- Properly make the unmap function based on encoders_post_disable()
with regarding to checks and iterators.
- Address checkpatch comment on "min = max = x()".
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180427231436.9353-1-paulo.r.zanoni@intel.com
Remove 4-bytes hole in this struct an reorder tables accordingly. This
also changes the last element of the tables to be more future-proof.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320220637.21480-8-lucas.demarchi@intel.com
Replace all users of pll->id to use pll->info->id. In functions using
this more than once it was preferred to add an id variable to make the
code easier to read.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320220637.21480-6-lucas.demarchi@intel.com
Replace all users of pll->funcs.* to use
pll->info->funcs->*. The extra indirection here is not on any critical
path and we can leave all const data together.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320220637.21480-4-lucas.demarchi@intel.com
This way we can stop copying fields from dpll_info to intel_shared_dpll
one by one. The migration of each field will come on separate patches.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320220637.21480-3-lucas.demarchi@intel.com
I confess I never fully understood that previous calculation,
so this is not a "fix". But let's simplify this math
so poor brains like mine can read and make some sense of
it in the future.
v2: Don't follow the spec since that gives invalid
values and it is also confusing. This Ville's
version is much simpler.
v3: Use u64 cast instead of declaring a u64 dco. (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115184257.8633-1-rodrigo.vivi@intel.com
Accordingly to spec "If Kdiv != 2, then Qdiv must be 1."
but we already handle qdiv values properly and this case here
should be spurious. But instead of blindly replacing let's
warn loudly instead. Because it means something was really
wrong on initial setup.
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-6-rodrigo.vivi@intel.com
Spec describe all values in MHz. We handle our
clocks in KHz. This includes the best_dco_centrality that was
forgot in the same unity as spec. Consequently we couldn't
get a good divider for high frequenies. Hence HDMI 2.0 wasn't
working.
Spec tells 999999 for initial best_dco_centrality meaning the
max value in MHz.
Since we convert dco from MHz to KHz we also need to convert
this initial best_doc_centrality to 999999000 or 999999999
or even better, to the max that its variable allow.
This patch also replaces the use of "* KHz(1)" with the values
directly on KHz to avoid future confusion.
v2: Use U32_MAX instead of random 99999 as spec tells. (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114234223.10600-1-rodrigo.vivi@intel.com
- 64 bits is not needed for afe_clock now we don't convert
that to Hz.
- 16 bits is not enough for all dco stuff.
- unsigned is not relevant/needed for all divisors values.
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-4-rodrigo.vivi@intel.com
No functional change. Just starting the wrpll fixes
with a clean-up to make units a bit more clear.
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-3-rodrigo.vivi@intel.com
"Display software must leave this field at the default value.
It no longer needs to be configured as part of PLL programming."
We respect this already and we are setting up the default
one line below: "DPLL_CFGCR1_CENTRAL_FREQ".
Also we don't touch anywhere else this central_freq for cnl.
So let's remove from the final write.
No functional change. Only a clean-up patch.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-2-rodrigo.vivi@intel.com
Replace dig_port->port with encoder->port in the BXT DPLL selection.
We can do this because both the master encoder and the fake MST encoders
have the same encoder->port value, whereas using dig_port->port only
worked for the master encoder since the fake encoders were't derived
from intel_digital_port. This eliminates the DP MST special case.
Do this by hand because spatch is having problems with the control
flow due to the dig_port assignment happening in two different
branches.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031205123.13123-8-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
On CNL we may need to bump up the system agent voltage not only due
to CDCLK but also when driving DDI port with a sufficiently high clock.
To that end start tracking the minimum acceptable voltage for each crtc.
We do the tracking via crtcs because we don't have any kind of encoder
state. Also there's no downside to doing it this way, and it matches how
we track cdclk requirements on account of pixel rate.
v2: Allow disabled crtcs to use the min voltage
Add IS_CNL check to intel_ddi_compute_min_voltage() since
we're using CNL specific values there
s/intel_compute_min_voltage/cnl_compute_min_voltage/ since
the function makes hw specific assumptions about the voltage
values
v3: Drop the test hack leftovers from skl_modeset_calc_cdclk()
v4: s/voltage/voltage_level/ (Rodrigo)
Replace DPLL DVFS FIXMEs with an explanation why we don't
do anything there (Rodrigo)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-9-ville.syrjala@linux.intel.com
HDMI Mode selection on CNL is on CFGCR0 for that PLL, not
on in a global CTRL1 as it was on SKL.
The original patch addressed this difference, but leaving behind
this single entry here. So we were checking the wrong bits during
the PLL initialization and consequently avoiding the CFGCR1 setup
during HDMI initialization. Luckly when only HDMI was in use BIOS
had already setup this for us. But the dual display with hot plug
were messed up.
Fixes: a927c927de ("drm/i915/cnl: Initialize PLLs")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003220859.21352-3-rodrigo.vivi@intel.com
Different from SKL we don't need ctrl1 and cfgcr2, but
we need to dump cfgcr0 and cfgcr1 instead.
v2: rebase and commit message
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170810224525.18278-1-rodrigo.vivi@intel.com
The function cnl_ddi_dp_set_dpll_hw_state does not need to be in global
scope, so make it static.
Cleans up sparse warning:
"symbol 'cnl_ddi_dp_set_dpll_hw_state' was not declared. Should it
be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170613134751.29196-1-colin.king@canonical.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Enable wrpll computation for Cannonlake platform to support
pll's required for HDMI output. The patch contains the following features
- compute Cannonlake port clock programming
dividers P, Q, and K.
- compute PLL parameters for Cannonlake. These parameters
set the values on DPLL registers.
- find the register values to program wrpll for Cannonlake.
The reference clock can be either 19.2MHz or 24MHz.
v2: rebase
v3: squash wrpll patches into one (Rodrigo)
v4: switch order of getting even dividers (Paulo)
update divider register values for PDiv and KDiv (Paulo)
update wrpll computation algorithm (Paulo)
v5: Remove ref clock division by 1000. (Rodrigo)
v6: Rodrigo rebasing on top of latest code.
Signed-off-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-18-git-send-email-rodrigo.vivi@intel.com
Although CNL follows PLL initialization more like Skylake
than Broxton we have a completely different initialization
sequence and registers used.
One big difference from SKL is that CDCLK PLL is now
exclusive (ADPLL) and for DDIs and MIPI we need to use
DFGPLLs 0, 1 or 2.
v2: Accept all Ander's suggestions and fixes:
- Registers and bits names prefix
- Group pll functions
- bits masks fixes
- remove read and modify on cfgcr1
- fix cfgcr0 setup
v3: Set SSC_ENABLE for DP.
Fix HDMI_MODE cfgcr0.
Avoid touch cfgcr0 on DP.
Add missed else on dpll_mgr definition so we use cnl one, not hsw.
v3: Centra freq should be always set to default and change bits
definitions to (1 << 1) instead of (1<<1). (by Paulo)
v4: Rebased.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-7-git-send-email-rodrigo.vivi@intel.com
The function intel_ddi_get_link_dpll() was added in f169660ed4
("drm/i915/dp: Add a standalone function to obtain shared dpll for
HSW/BDW/SKL/BXT") to "allow for the implementation of a platform
neutral upfront link training function", but such implementation
never landed.
So remove that function and clean up the exported shared DPLL interface.
Fixes: f169660ed4 ("drm/i915/dp: Add a standalone function to obtain shared dpll for HSW/BDW/SKL/BXT")
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484310032-1863-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Add the missing INTEL_OUTPUT_DP_MST case in bxt_get_dpll()
to correctly initialize the crtc_state and port plls when
link training a DP MST monitor on BXT/APL devices.
Fixes: a277ca7dc0 ("drm/i915: Split bxt_ddi_pll_select()")
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=99572
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Gary C Wang <gary.c.wang@intel.com>
Reviewed-by: Ciobanu, Nathan D <nathan.d.ciobanu@intel.com>
Reviewed-by: Herbert, Marc <marc.herbert@intel.com>
Reviewed-by: Bride, Jim <jim.bride@intel.com>
Reviewed-by: Navare, Manasi D <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486096329-6255-1-git-send-email-shawn.c.lee@intel.com
Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.
So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).
The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.
v2: fix conflict with IS_LP and 3 new cases for this
big core bucket:
- intel_ddi.c: intel_ddi_get_link_dpll
- intel_fbc.c: find_compression_threshold
- i915_gem_gtt.c: gtt_write_workarounds
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com
The function intel_atomic_get_shared_dpll_state() is only called from
intel_dpll_mgr.c and it concerns the same data structures as the other
functions in that file, so move it there and make it static.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-8-git-send-email-ander.conselvan.de.oliveira@intel.com
Remove the IS_PLATFORM() macros from intel_dump_pipe_config() and split
that logic in platform specific implementations inside the dpll code,
accessed through a platform independent interface.
v2: Rebase.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-7-git-send-email-ander.conselvan.de.oliveira@intel.com
The documentation for most of the non-static members and structs were
missing. Fix that.
v2: Fix typos (Durga)
v3: Rebase.
Fix make docs warnings.
Document more.
v4: capitilize CRTC; say that the prepare hook is a nop if the DPLL is
already enabled; link to struct intel_dpll_hw_state from @hw_state
field in struct intel_shared_dpll_state; reorganize DPLL flags; link
intel_shared_dpll_state to other structs and functions. (Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-6-git-send-email-ander.conselvan.de.oliveira@intel.com
The function intel_shared_dpll_commit() performs the equivalent of
drm_atomic_helper_swap_state() for the shared dpll state, which is not
handled by the helpers. So make it do a full swap of the state and
rename it for consistency.
v2: Fix typo in the commit message. (Durga)
v3: Rebase.
v4: Swap the states instead of just renaming the function. (Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com> (v2)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-3-git-send-email-ander.conselvan.de.oliveira@intel.com
While the details of getting a shared dpll are wrapped by
intel_get_shared_dpll(), the release was still hand rolled into the
modeset code. Fix that by creating an entry point for releasing the
pll and move that code there.
v2: Take old_dpll from crtc->state instead of crtc_state. (CI)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-2-git-send-email-ander.conselvan.de.oliveira@intel.com
Follow the PLL enable sequence updated in bspec, which requires the DCC
delay range 2 bit to be set.
v2: Moved from DDI init sequence to PLL enable.
v3: Don't read value from GRP register. (Rodrido)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-5-git-send-email-ander.conselvan.de.oliveira@intel.com
Geminilake is mostly backwards compatible with broxton, so change most
of the IS_BROXTON() checks to IS_GEN9_LP(). Differences between the
platforms will be implemented in follow-up patches.
v2: Don't reuse broxton's path in intel_update_max_cdclk().
Don't set plane count as in broxton.
v3: Rebase
v4: Include the check intel_bios_is_port_hpd_inverted().
Commit message.
v5: Leave i915_dmc_info() out; glk's csr version != bxt's. (Rodrigo)
v6: Rebase.
v7: Convert a few mode IS_BROXTON() occurances in pps, ddi, dsi and pll
code. (Rodrigo)
v8: Squash a couple of DDI patches with more conversions. (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-2-git-send-email-ander.conselvan.de.oliveira@intel.com
A bunch of source files with just a few instances of the
incorrect INTEL_INFO use.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The port registers related to the phys in broxton map to different
channels and specific phys. Make that mapping explicit.
v2: Pass enum dpio_phy to macros instead of mmio base. (Imre)
v3: Fix typo in macros. (Imre)
v4: Also change variables from u32 to enum dpio_phy. (Imre)
Remove leftovers from previous version. (Imre)
v5: Actually git add the changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476863940-6019-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Saves 1392 bytes of .rodata strings.
Also change a few function/macro prototypes in i915_gem_gtt.c
from dev to dev_priv where it made more sense to do so.
v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Mention function prototype changes. (David Weinehall)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
This saves 3248 bytes of .rodata strings.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Gustavo A. R. Silva