Update various registers fields definitions for the DWC_usb31 controller
for SuperSpeedPlus support.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a convenience function to check if the controller is DWC_usb31.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.
Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.
The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.
Add checking for the new ID to pass driver probe.
Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.
Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registers DWC3's ULPI interface with the ULPI bus when it's
available.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make selection between ULPI and UTMI+ interfaces possible by
providing definition for the bit in Global USB2 PHY
Configuration Register that controls it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Definitions for Global USB2 PHY Vendor Control Register
bits. We will need them to access ULPI PHY registers later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes "Enable USB3 LPM Capability" option from Kconfig
and adds snps,usb3_lpm_capable devicetree property instead of it.
USB3 LPM (Link Power Management) capability is hardware property, and
it's platform dependent, so if our hardware supports this feature, we
want rather to configure it in devicetree than having it as Kconfig option.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.
This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Newer DWC3 controllers can be built for USB 2.0-only mode, where
most of the USB 3.0 circuitry is left out. To support this mode,
the driver must limit the speed programmed into the DCFG register
to Hi-Speed or lower.
Reads and writes to the PIPECTL register are left as-is, since
they should be no-ops in USB 2.0-only mode. Calls to phy_init()
etc. for the USB3 phy are also left as-is, since the no-op USB3
phy should be used for USB 2.0-only mode controllers.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
power_on and power_off the following APIs are used phy_init(), phy_exit(),
phy_power_on() and phy_power_off().
However using the old USB phy library wont be removed till the PHYs of all
other SoC's using dwc3 core is adapted to the Generic PHY Framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
few new revisions of the core have been released,
add them to our list of revisions so we can apply
workarounds if necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 388e5c5 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.
Cc: <stable@vger.kernel.org> # v3.8+
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We must read HWPARAMS4 register to figure out
how many scratch buffers we should allocate.
Later patch will use "Set Scratchpad Buffer
Array" command to pass the pointer to the
IP so it can be used during hibernation.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This extra field will save endpoint state when we're
about to enter hibernation. It will be used later
to restore the endpoint state when resuming.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
move 1-bit flags to the bottom of the structure,
sort all bit flags alphabetically, add documentation
which was missing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.
Because of that, what used to be 8 bits long, has become 9 bits long.
Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.
So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits
This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.
[ balbi@ti.com : improve commit log a bit ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
That register has more than just the event buffer
size; we can also mask and unmask that particular
interrupter on bit 31 of that register.
In this patch we introduce the necessary macros
and make sure to use the new macros while also
making sure we mask interrupts during driver
removal.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the macro DWC3_DCFG_LPM_CAP was defined twice.
This patch just removes one of the definitions,
no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adapts the dwc3 to use the device tree helper
"of_usb_get_dr_mode" for the mode of operation of the dwc3 instance
being probed.
[ balbi@ti.com : make of_usb_get_dr_mode() conditional on
dev->of_node and let pdata pass dr_mode too ]
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
@list is not as a parameter of dwc3_event_buffer, so remove it in
comments.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn