Goodix CTP controllers require AVDD28, VDDIO regulators for power-on
sequence.
The delay between these regualtor operations as per Power-on Timing
from datasheet[1] is 0 (T1 >= 0 usec).
So, enable and disable these regulators in proper order using normal
regulator functions without any delay in between.
[1] GT5663 Datasheet_English_20151106_Rev.01
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are many Lenovo laptops which need elan_i2c support, this patch adds
relevant IDs to the Elan driver so that touchpads are recognized.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- update the ili210x touchscreen driver, refreshing the code and adding
support for ILI251X line
- add support for st1633 to the st1232 touchscreen driver
- add support for sx8650 to the the sx8654 touchscreen driver
- add support for Evervision FT5726 to the edt-ft5x06 touchscreen
driver
- add support for gt5688 to the Goodix touchscreen driver
- new vibrator driver for MSM SOCs
- miscellaneous fixes for the rest of input drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: wacom_serial4 - add support for Wacom ArtPad II tablet
Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
Input: msm-vibrator - use correct gpio header
Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
Input: i8042 - rework DT node name comparisons
Input: goodix - print values in case of inconsistencies
Input: goodix - refer to touchscreen.txt in device tree bindings
Input: goodix - support Goodix gt5688
Input: synaptics_i2c - remove redundant spinlock
Input: db9 - mark expected switch fall-through
Input: qt2160 - remove redundant spinlock
Input: st1232 - handle common DT bindings
Input: ims-pcu - switch to using brightness_set_blocking()
Input: st1232 - switch to gpiod API
Input: ili210x - fetch touchscreen geometry from DT
Input: msm-vibrator - tweak an error message
Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
Input: stmfts - acknowledge that setting brightness is a blocking call
Input: ili210x - switch to using devm_device_add_group()
...
Tablet initially begins communicating at 9600 baud, so this command
should be used to connect to the device:
$ inputattach --daemon --baud 9600 --wacom_iv /dev/ttyS0
https://github.com/linuxwacom/xf86-input-wacom/issues/40
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo s21e-20 uses ELAN0601 in its ACPI tables for the Elan touchpad.
Signed-off-by: Vincent Batts <vbatts@hashbangbash.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When CONFIG_INPUT_POLLDEV is disabled, we get a link error:
drivers/input/touchscreen/raspberrypi-ts.o: In function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0xec): undefined reference to `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0xec): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0x19c): undefined reference to `input_register_polled_device'
raspberrypi-ts.c:(.text+0x19c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `input_register_polled_device'
Select that symbol like we do from the other similar drivers.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When CONFIG_GPIOLIB is not set, we get a couple of build
errors during test building:
drivers/input/misc/msm-vibrator.c: In function 'msm_vibrator_start':
drivers/input/misc/msm-vibrator.c:79:3: error: implicit declaration of function 'gpiod_set_value_cansleep'; did you mean 'gpio_set_value_cansleep'? [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(vibrator->enable_gpio, 1);
^~~~~~~~~~~~~~~~~~~~~~~~
gpio_set_value_cansleep
drivers/input/misc/msm-vibrator.c: In function 'msm_vibrator_probe':
drivers/input/misc/msm-vibrator.c:176:26: error: implicit declaration of function 'devm_gpiod_get'; did you mean 'devm_gpio_free'? [-Werror=implicit-function-declaration]
vibrator->enable_gpio = devm_gpiod_get(&pdev->dev, "enable",
^~~~~~~~~~~~~~
devm_gpio_free
drivers/input/misc/msm-vibrator.c:177:13: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
GPIOD_OUT_LOW);
^~~~~~~~~~~~~
GPIOF_INIT_LOW
drivers/input/misc/msm-vibrator.c:177:13: note: each undeclared identifier is reported only once for each function it appears in
This is easy to avoid when we use gpio/consumer.h as the documented interface.
Fixes: 0f681d09e6 ("Input: add new vibrator driver for various MSM SOCs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection driver
is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8
release, I'm sending them along with the other updates.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0u1N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection
driver is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8 release,
I'm sending them along with the other updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
...
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
While here, correct MODULE_LICENSE() string to be aligned with license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ACPI allows to enumerate specific devices by using compatible strings.
Enable that enumeration for EDT touchscreen devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VjX6
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/late
DaVinci SoC updates for v5.1 (part 3)
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
* tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (57 commits)
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
ARM: davinci: aintc: unify error handling
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_suspend':
drivers/input/touchscreen/ti_am335x_tsc.c:510:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_resume':
drivers/input/touchscreen/ti_am335x_tsc.c:527:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
It's not used any more after 333e07ec4b ("Input: ti_am335x_tsc: Mark TSC
device as wakeup source")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The mach/ and asm/ includes are not needed in davinci_keyscan, but they
will cause build problems once we make mach/irqs.h a private header for
mach-davinci.
Remove all unused header includes.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Convert string compares of DT node names to use of_node_name_eq helper
instead. For the root node on SUN DT, we need to retrieve the 'name'
property as it is the rare case where the 'name' property and node name
differ. With both changes, it removes direct access to the node name
pointer.
While at it, convert the open coded loop to use for_each_child_of_node().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- tweaks to Elan drivers (both PS/2 and I2C) to support new devices.
Also revert of one of IDs as that device should really be driven by
i2c-hid + hid-multitouch
- a few drivers have been switched to set_brightness_blocking() call
because they either were sleeping the their set_brightness()
implementation or used workqueue but were not canceling it on unbind.
- ps2-gpio and matrix_keypad needed to [properly] flush their works to
avoid potential use-after-free on unbind.
- other miscellaneous fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ACPI ID for touchpad in Lenovo V330-15ISK
Input: st-keyscan - fix potential zalloc NULL dereference
Input: apanel - switch to using brightness_set_blocking()
Revert "Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G"
Input: qt2160 - switch to using brightness_set_blocking()
Input: matrix_keypad - use flush_delayed_work()
Input: ps2-gpio - flush TX work when closing port
Input: cap11xx - switch to using set_brightness_blocking()
Input: elantech - enable 3rd button support on Fujitsu CELSIUS H780
Input: bma150 - register input device after setting private data
Input: pwm-vibra - stop regulator after disabling pwm, not before
Input: pwm-vibra - prevent unbalanced regulator
Input: snvs_pwrkey - allow selecting driver for i.MX 7D
"Invalid config" gives little idea what's wrong. Print the values that
must not be 0 so we know which ones are off.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove a leftover spinlock.
This was required back when mod_delayed_work() did not exist, and had to
be implemented with a cancel + queue. See commit e7c2f96744
("workqueue: use mod_delayed_work() instead of __cancel + queue")
schedule_delayed_work() and mod_delayed_work() can now be used
concurrently. So the spinlock is no longer needed.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds ELAN0617 to the ACPI table to support Elan touchpad found in
Lenovo V330-15ISK.
Signed-off-by: Mauro Ciancio <mauro@acadeu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that LEDs core allows "blocking" flavor of "set brightness" method we
can use it and get rid of private work item. As a bonus, we are no longer
forgetting to cancel it when we unbind the driver.
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/input/joystick/db9.c: In function ‘db9_saturn_read_packet’:
drivers/input/joystick/db9.c:256:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (tmp == 0xff) {
^
drivers/input/joystick/db9.c:263:2: note: here
default:
^~~~~~~
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove a spinlock which prevents schedule_delayed_work() and
mod_delayed_work() from executing concurrently.
This was required back when mod_delayed_work() did not exist,
and had to be implemented with a cancel + schedule. See
commit e7c2f96744 ("workqueue: use mod_delayed_work() instead of
__cancel + queue")
schedule_delayed_work() and mod_delayed_work() can now be used
concurrently. So the spinlock is no longer needed.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is required to specify generic touchscreen properties via DT.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that LEDs core allows "blocking" flavor of "set brightness" method we
can use it and get rid of private work item.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_gpiod_get_optional() and gpiod_set_value_cansleep() instead
of the old API. The st1232_ts_power() now passes on the inverted "poweron"
value to reflect the correct logical value.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 7db54c89f0 as it
breaks Acer Aspire V-371 and other devices. According to Elan:
"Acer Aspire F5-573G is MS Precision touchpad which should use hid
multitouch driver. ELAN0501 should not be added in elan_i2c."
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202503
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that LEDs core allows "blocking" flavor of "set brightness" method we
can use it and get rid of private work items.
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fetching the geometry from the ILI251x registers seems unreliable and
sometimes returns all zeroes. Add support for fetching the geometry and
axis inversion from DT instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PTR_ERR(NULL) value is zero and it's not useful to print that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should be using flush_delayed_work() instead of flush_work() in
matrix_keypad_stop() to ensure that we are not missing work that is
scheduled but not yet put in the workqueue (i.e. its delay timer has not
expired yet).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To ensure that TX work is not running after serio port has been torn down,
let's flush it when closing the port.
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Acked-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Updating LED state requires access to regmap and therefore we may sleep,
so we could not do that directly form set_brightness() method.
Historically we used private work to adjust the brightness, but with the
introduction of set_brightness_blocking() we no longer need it.
As a bonus, not having our own work item means we do not have
use-after-free issue as we neglected to cancel outstanding work on
driver unbind.
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Like Fujitsu CELSIUS H760, the H780 also has a three-button Elantech
touchpad, but the driver needs to be told so to enable the middle touchpad
button.
The elantech_dmi_force_crc_enabled quirk was not necessary with the H780.
Also document the fw_version and caps values detected for both H760 and
H780 models.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to access I2C bus when switching brightness, and that may block,
therefore we have to set stmfts_brightness_set() as LED's
brightness_set_blocking() method.
Fixes: 72d1f2346d ("Input: tm2-touchkey - add touchkey driver support for TM2")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.
Fixes: 78bcac7b2a ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By switching to devm_device_add_group() we can complete driver conversion
to using managed resources and get rid of ili210x_i2c_remove().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI251x touch controller. This controller is similar
to the ILI210x, except for the following differences:
- Does not support I2C R-W transfer, Read must be followed by an
obscenely long delay, and then followed by Write
- Does support 10 simultaneous touch inputs.
- Touch data format is slightly different, pressure reporting does not
work although the touch data contain such information.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Perform the register access only after the I2C client data are set,
this is only done in preparation for the subsequent patch which
uses the I2C client data in the register IO function.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the packed structures for representing data as that does not
apply to other similar Ilitek touchscreens. Instead, implement a function
which parses the data and reports touch events and coordinates.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the driver to devm_request_irq(), drop the related unmanaged
deregistration code and add ili210x_irq_teardown() to tear the IRQ
down and cancel possible touchscreen pending work.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen can have a reset GPIO connected to it, add support
for such an arrangement.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The .get_pendown_state callback is set only by the platform data code,
which was just removed. Thus, get_pendown_state() always returns false,
so drop that altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is not a single user of the ili210x platform data in the kernel,
just drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a new vibrator driver that supports various Qualcomm
MSM SOCs. Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some platforms (e.g.: ARCH_BRCMSTB) it is possible to enter
"poweroff" while leaving some wake-up sources enabled such as key
presses in order to allow for the system to wake-up.
Wire up a .shutdown() callback which calls into the existing
gpio_keys_suspend() since the logic is essentially the same.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should rely on the interrupt trigger (level vs edge) set up by the
firmware or board code instead of forcing what we consider appropriate.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some of the #defined register values are one-bit flags. Convert them to
use the BIT(x) macro instead of 1 byte hexadecimal values. This improves
readability and clarifies the intent.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Revert the commits that introduce clk management for the SP
clk on MMP2 SoCs (used for OLPC). Turns out it wasn't a good
idea and there isn't any need to manage this clk, it just causes
more headaches.
- A performance regression that went unnoticed for many years where
we would traverse the entire clk tree looking for a clk by name
when we already have the pointer to said clk that we're looking
for
- A parent linkage fix for the qcom SDM845 clk driver
- An i.MX clk driver rate miscalculation fix where order of operations
were messed up
- One error handling fix from the static checkers
-----BEGIN PGP SIGNATURE-----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=G4M9
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Mostly driver fixes, but there's a core framework fix in here too:
- Revert the commits that introduce clk management for the SP clk on
MMP2 SoCs (used for OLPC). Turns out it wasn't a good idea and
there isn't any need to manage this clk, it just causes more
headaches.
- A performance regression that went unnoticed for many years where
we would traverse the entire clk tree looking for a clk by name
when we already have the pointer to said clk that we're looking for
- A parent linkage fix for the qcom SDM845 clk driver
- An i.MX clk driver rate miscalculation fix where order of
operations were messed up
- One error handling fix from the static checkers"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc: Use active only source for CPUSS clocks
clk: ti: Fix error handling in ti_clk_parse_divider_data()
clk: imx: Fix fractional clock set rate computation
clk: Remove global clk traversal on fetch parent index
Revert "dt-bindings: marvell,mmp2: Add clock id for the SP clock"
Revert "clk: mmp2: add SP clock"
Revert "Input: olpc_apsp - enable the SP clock"
of_touchscreen.c provides a common interface for a axis inversion and
swapping of touchscreens. Therefore use it in the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 and sx8650 are quite similar, therefore add support for the
sx8650 within the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: use __be16 in sx8650_irq, add missing del_timer_sync]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the sx865[456] share the same datasheet and differ only in the
presence of a "capacitive proximity detection circuit" and a "haptics
motor driver for LRA/ERM" add them to the compatbiles. As the driver
doesn't implement these features it should be no problem.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 features a NRST input which may be connected to a GPIO.
Therefore add support for hard-resetting the sx8654 via this NRST.
If the reset-gpio property is provided the sx8654 is resetted via NRST
instead of the soft-reset via I2C.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds myself as an author of the st1232 driver module as Tony's
email address doesn't seem to work anymore.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the Sitronix ST1633 touchscreen controller to the st1232
driver. A protocol spec can be found here:
www.ampdisplay.com/documents/pdf/AM-320480B6TZQW-TC0H.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes order of disable calls in pwm_vibrator_stop.
Currently when starting device, we first enable vcc regulator and then
setup and enable pwm. When stopping, we should do this in oposite order,
so first disable pwm and then disable regulator.
Previously order was the same as in start.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
pwm_vibrator_stop disables the regulator, but it can be called from
multiple places, even when the regulator is already disabled. Fix this
by using regulator_is_enabled check when starting and stopping device.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i.MX SNVS Power Key driver supports the i.MX 7D SoC family too.
Allow to enable the i.MX SNVS Power Key driver even if only i.MX 7D
SoC is selected.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fixup for the input_event fix for y2038 Sparc64, and couple other
minor fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: input_event - fix the CONFIG_SPARC64 mixup
Input: olpc_apsp - assign priv->dev earlier
Input: uinput - fix undefined behavior in uinput_validate_absinfo()
Input: raspberrypi-ts - fix link error
Input: xpad - add support for SteelSeries Stratus Duo
Input: input_event - provide override for sparc64
Turns out this is not such a great idea. Once the SP clock is disabled,
it's not sufficient to just enable in order to bring the SP core back up.
It seems that the kernel has no business managing this clock. Just let
the firmware keep it enabled.
This reverts commit ed22cee91a.
Link: https://lore.kernel.org/lkml/154783267051.169631.3197836544646625747@swboyd.mtv.corp.google.com/
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The dev field needs to be set when serio_register_port() is called,
because the open callback may use it (in the error handling path).
Fixes: commit af518342ef ("Input: olpc_apsp - check FIFO status on open(), not probe()")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STPMIC1 pmic is able to manage an onkey button. This driver exposes
the STPMIC1 onkey as an input device. It can also be configured to
shut-down the power supplies on a long key-press with an adjustable
duration.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch removes common ADC settings in favor to use
stmpe811_adc_common_init that is present in MFD. This is necessary in
preparation for the stmpe-adc driver, because those two drivers have
common settings for the ADC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move defines that are ADC related to the header of the overlying MFD,
so they can be used from multiple sub-devices.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An integer overflow may arise in uinput_validate_absinfo() if "max - min"
can't be represented by an "int". We should check for overflow before
trying to use the result.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into for-linus
Sync with mainline to get linux/overflow.h among other things.
Fix link error when TOUCHSCREEN_RASPBERRYPI_FW is enabled as a module and
the dependent module is built-in. The 'depends on RASPBERRYPI_FIRMWARE' by
itself prevents the touchscreen driver from being built-in when the
firmware is configured as a module. However, the '|| COMPILE_TEST' still
allows it unless we explicitly prevent that configuration with
'|| (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)'.
ld: drivers/input/touchscreen/raspberrypi-ts.o: in function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0x3a8): undefined reference to `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x3a8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x4c8): undefined reference to `rpi_firmware_property'
ld: raspberrypi-ts.c:(.text+0x4c8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_property'
Rework so that TOUCHSCREEN_RASPBERRYPI_FW depends on
RASPBERRYPI_FIRMWARE=n if COMPILE_TEST is enabled.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the SteelSeries Stratus Duo, a wireless Xbox 360
controller. The Stratus Duo ships with a USB dongle to enable wireless
connectivity, but it can also function as a wired controller by connecting
it directly to a PC via USB, hence the need for two USD PIDs. 0x1430 is the
dongle, and 0x1431 is the controller.
Signed-off-by: Tom Panfil <tom@steelseries.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately the evervision focaltech implementation uses two offset
registers, one for the x coordinate and one for y.
This patch extends the driver to handle those offset registers only for
devices that support these.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently only the threshold and gain parameters can be read.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Evervision displays are using different Focaltech touchscreen
controllers. This commit adds the initial support for the ones using the
FT5726 controller. Receiving the touch data is the same as for the
GENERIC_FT but the x and y cooridnates are swapped. The main differences
are the register addresses where the GAIN and THRESHOLD parameters are
stored.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
iSOrt includes in alphabetical order and remove duplicated include file
linux/kernel.h
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with
memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into next
Merge with mainline to bring in the new APIs.
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
regmap_bulk_read() can return a non zero value on failure. The fix checks
if the function call succeeded before calling mod_timer. The issue was
identified by a static analysis tool.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchkey variant found on aries board is slighty different,
it uses a fixed regulator and writes/read to the same place
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Not all devices use the same keycodes in the same order,
so add possibility to define keycodes for buttons present
on actual hardware.
If keycodes property is not present, we assume that device has
at least MENU and BACK keys.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
tm2-touchkey doesn't have brightness levels, but only on/off states,
so replace LED_FULL with LED_ON.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchkey on midas boards is almost identical.
The only real difference is that it uses the same register for both
keycode and base.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Microsoft documenation for the PNP0C40 device aka the
"Windows-compatible button array" describes the 5th GpioInt listed in
the resources as: '5. Interrupt corresponding to the "Rotation Lock"
button, if supported'.
Notice this describes the 5th entry as a button while we sofar have been
mapping it to EV_SW, SW_ROTATE_LOCK. On my Point of View TAB P1006W-232
which actually comes with a rotation-lock button, the button indeed is a
button and not a slider/switch. An image search for other Windows tablets
has found 2 more models with a rotation-lock button and on both of those
it too is a push-button and not a slider/switch.
Further evidence can be found in the HUT extension HUTRR52 from Microsoft
which adds rotation lock support to the HUT, which describes 2 different
usages: "0xC9 System Display Rotation Lock Button" and
"0xCA System Display Rotation Lock Slider Switch" note that switch is seen
as a separate thing here and the non switch wording is an exact match for
the "Windows-compatible button array" spec wording.
TL;DR: our current mapping of the 5th GPIO to SW_ROTATE_LOCK is wrong
because the 5th GPIO is for a push-button not a switch.
This commit fixes this by maping the 5th GPIO to KEY_ROTATE_LOCK_TOGGLE.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ACPI0011 _DSD button descriptor on a CHT based Intel Compute Sticks
contains a mapping for usage-page 0x01 usage-id 0xca.
As described in hutrr52_system_display_rotation_lock_controls_0.pdf this
should be mapped as a "System Display Rotation Lock Slider Switch", this
commit adds support for this, silencing the following warning:
soc_button_array ACPI0011:00: Unknown button index 4 upage 01 usage ca,
ignoring
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A tiny pull request this merge window unfortunately, should get more
material in for the next release:
- new driver for Raspberry Pi's touchscreen (firmware interface)
- miscellaneous input driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G
Input: atmel_mxt_ts - don't try to free unallocated kernel memory
Input: drv2667 - fix indentation issues
Input: touchscreen - fix coding style issue
Input: add official Raspberry Pi's touchscreen driver
Input: nomadik-ske-keypad - fix a loop timeout test
Input: rotary-encoder - don't log EPROBE_DEFER to kernel log
Input: olpc_apsp - remove set but not used variable 'np'
Input: olpc_apsp - enable the SP clock
Input: olpc_apsp - check FIFO status on open(), not probe()
Input: olpc_apsp - drop CONFIG_OLPC dependency
clk: mmp2: add SP clock
dt-bindings: marvell,mmp2: Add clock id for the SP clock
Input: ad7879 - drop platform data support
Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Drivers:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding
-----BEGIN PGP SIGNATURE-----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=5He5
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Driver updates:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding"
* tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: rename core files
rtc: nvmem: fix possible use after free
rtc: add i.MX system controller RTC support
dt-bindings: fsl: scu: add rtc binding
rtc: pcf2123: Add Microcrystal rv2123
rtc: class: reimplement devm_rtc_device_register
rtc: enforce rtc_timer_init private_data type
rtc: abx80x: Implement RTC_VL_READ,CLR ioctls
rtc: pcf85363: Add support for NXP pcf85263 rtc
dt-bindings: rtc: pcf85363: Document pcf85263 real-time clock
rtc: pcf8523: don't return invalid date when battery is low
dt-bindings: rtc: use a generic node name for ds1307
PM: Switch to use %ptR
m68k/mac: Switch to use %ptR
Input: hp_sdc_rtc - Switch to use %ptR
rtc: tegra: Switch to use %ptR
rtc: s5m: Switch to use %ptR
rtc: s3c: Switch to use %ptR
rtc: rx8025: Switch to use %ptR
rtc: rx6110: Switch to use %ptR
...
This adds ELAN0501 to the ACPI table to support Elan touchpad found in ASUS
Aspire F5-573G.
Signed-off-by: Patrick Dreyer <Patrick.Dreyer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <sanjeev_chugh@mentor.com>
Fixes: a4891f1058 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull parisc updates from Helge Deller:
"The major change in this patchset is the new system call table
generation support from Firoz Khan"
* 'parisc-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: syscalls: ignore nfsservctl for other architectures
parisc: generate uapi header and system call table files
parisc: add system call table generation support
parisc: remove __NR_Linux from uapi header file.
parisc: add __NR_syscalls along with __NR_Linux_syscalls
parisc: move __IGNORE* entries to non uapi header
parisc: Fix HP SDC hpa address output
parisc: Fix serio address output
parisc: Split out alternative live patching code
There are some statements that are indented incorrectly, fix this by
removing the extra tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Switching a few devices with Synaptics over to SMbus and disabling
SMbus on a couple devices with Elan touchpads as they need more
plumbing on PS/2 side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - enable SMBus for HP EliteBook 840 G4
Input: elantech - disable elan-i2c for P52 and P72
Input: synaptics - enable RMI on ThinkPad T560
Input: omap-keypad - fix idle configuration to not block SoC idle states
dmesg reports that "Your touchpad (PNP: SYN3052 SYN0100 SYN0002 PNP0f13)
says it can support a different bus."
I've tested the offered psmouse.synaptics_intertouch=1 with 4.18.x and
4.19.x and it seems to work well. No problems seen with suspend/resume.
Also, it appears that RMI/SMBus mode is actually required for 3-4 finger
multitouch gestures to work -- otherwise they are not reported at all.
Information from dmesg in both modes:
psmouse serio3: synaptics: Touchpad model: 1, fw: 8.2, id: 0x1e2b1,
caps: 0xf00123/0x840300/0x2e800/0x0, board id: 3139, fw id: 2000742
psmouse serio3: synaptics: Trying to set up SMBus access
rmi4_smbus 6-002c: registering SMbus-connected sensor
rmi4_f01 rmi4-00.fn01: found RMI device,
manufacturer: Synaptics, product: TM3139-001, fw id: 2000742
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes the coding style problem reported
by checkpatch.pl as below:
ERROR: foo* bar should be "foo *bar"
Signed-off-by: Hardik Singh Rathore <hardiksingh.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Jagan Teki