Commit Graph

611 Commits

Author SHA1 Message Date
Archit Taneja 6b84937577 OMAPDSS: DSI: Rename dsi_videomode_data to dsi_videomode_timings
The struct omap_dss_dsi_videomode_data holds fields which need to be configured
for DSI to operate in video mode. Rename the struct to dsi_videomode_timings.

One reason to do this is because most of the fields in the struct are timings
related. The other reason is to create a generic op for output specific
timings. This generic op can be considered as a way to set custom or private
timings for the output.

In the case of OMAP, DSI and RFBI require some more timings apart from the
relgular DISPC timings. The structs omap_dss_videomode_timings and rfbi_timings
can be considered as these output specific timings respectively.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-16 18:02:11 +05:30
Archit Taneja dca2b1522c OMAPDSS: DSI: Maintain copy of operation mode in driver data
The DSI driver currently relies on the omap_dss_device struct to know the mode
of operation of the DSI protocol(command or video mode). This makes the DSI
interface driver dependent on the omap_dss_device struct.

Make the DSI driver data maintain it's own operation mode field. The panel
driver is expected to call omapdss_dsi_set_operation_mode() before the interface
is enabled.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-16 18:02:00 +05:30
Archit Taneja 889b4fd7ee OMAPDSS: SDI: Maintain copy of data pairs in driver data
The SDI driver currently relies on the omap_dss_device struct to configure the
number of data pairs as specified by the panel. This makes the SDI interface
driver dependent on the omap_dss_device struct.

Make the SDI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_sdi_set_datapairs() before enabling the interface.
Even though we configure the number of data pairs here, this function would be
finally mapped to a generic interface op called set_data_lines. The datapairs
argument type has been changed from u8 to int at some places to be in sync with
the 'set_data_lines' ops of other interfaces.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-16 18:00:55 +05:30
Archit Taneja c6b393d4bc OMAPDSS: DPI: Maintain copy of number of data lines in driver data
The DPI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the DPI interface
driver dependent on the omap_dss_device struct.

Make the DPI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_dpi_set_data_lines() before enabling the interface.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-16 18:00:55 +05:30
Archit Taneja 475989b763 OMAPDSS: RFBI: Maintain copy of number of data lines in driver data
The RFBI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the RFBI interface
driver dependent on the omap_dss_device struct.

Make the RFBI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_rfbi_set_data_lines() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-16 18:00:54 +05:30
Archit Taneja b02875be08 OMAPDSS: RFBI: Maintain copy of pixel size in driver data
The RFBI driver currently relies on the omap_dss_device struct to receive the
desired pixel size of the panel. This makes the RFBI interface driver dependent
on the omap_dss_device struct.

Make the RFBI driver data maintain it's own pixel format field. A panel driver
is expected to call omapdss_rfbi_set_pixel_size() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-16 18:00:54 +05:30
Archit Taneja 02c3960b1e OMAPDSS: DSI: Maintain copy of pixel format in driver data
The DSI driver currently relies on the omap_dss_device struct to receive the
desired pixel format of the panel. This makes the DSI interface driver dependent
on the omap_dss_device struct.

Make the DSI driver data maintain it's own pixel format field. The panel driver
is expected to call omapdss_dsi_set_pixel_format() to configure the pixel format
before the interface is enabled.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-16 18:00:47 +05:30
Archit Taneja 6ff9dd5a6f OMAPDSS: RFBI: Add function to set panel size
RFBI drivers requires configuration of the update area. Since we don't support
partial updates, the size to be configures is the panel size itself.

Add a timings field in RFBI's driver data. Apart from x_res and y_res, all the
other fields are configured to an initial value when RFBI is enabled. A panel
driver is expected to call omapdss_rfbi_set_size() configure the size of the
panel.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-15 15:53:09 +05:30
Archit Taneja 43eab86167 OMAPDSS: RFBI: Remove partial update support
Partial update suppport was removed from DISPC and DSI sometime back. The RFBI
driver still tries to support partial update without the underlying support in
DISPC.

Remove partial update support from RFBI, only support updates which span acros
the whole panel size. This also helps in DSI and RFBI having similar update
ops.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-15 15:53:08 +05:30
Archit Taneja c7833f7bc0 OMAPDSS: SDI: Create a function to set timings
Create function omapdss_sdi_set_timings(). Configuring new timings is done the
same way as before, SDI is disabled, and re-enabled with the new timings in
dssdev. This just moves the code from the panel drivers to the SDI driver.

The panel drivers shouldn't be aware of how SDI manages to configure a new set
of timings. This should be taken care of by the SDI driver itself.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-15 15:48:45 +05:30
Archit Taneja e352574db5 OMAPDSS: DSI: Add function to set panel size for command mode panels
DSI command mode panels don't need to configure a full set of timings to
configure DSI, they only require the width and the height of the panel in
pixels.

Use omapdss_dsi_set_size for command mode panels, omapdss_dsi_set_timings is
meant for video mode panels. When performing rotation via chaning the address
mode of the panel, we would need to swap width and height when doing 90 or 270
rotation. Make sure that omapdss_dsi_set_size() makes the new width and height
visible to DSI.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-13 15:44:39 +05:30
Archit Taneja e67458a831 OMAPDSS: DSI: Maintain own copy of timings in driver data
The DSI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC and DSI blocks accordingly. This makes the DSI interface
driver dependent on the omap_dss_device struct.

Make the DSI driver data maintain it's own timings field. A DSI video mode panel
driver is expected to call omapdss_dsi_set_timings() to set these timings before
the panel is enabled.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-13 15:44:39 +05:30
Archit Taneja c499144c3b OMAPDSS: DPI: Maintain our own timings field in driver data
The DPI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC accordingly. This makes the DPI interface driver dependent
on the omap_dss_device struct.

Make the DPI driver data maintain it's own timings field. The panel driver is
expected to call dpi_set_timings()(renamed to omapdss_dpi_set_timings) to set
these timings before the panel is enabled.

In the set_timings() op, we still ensure that the omap_dss_device timings
(dssdev->panel.timings) are configured. This will later be configured only by
the DPI panel drivers.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-08-13 15:44:39 +05:30
Leela Krishna Amudala a44cf75dcb include/video: Add register offsets for FIMD version 8
FIMD version 8 has VIDTCON and VIDCON registers at different offsets
from the previous versions. Hence, adding the macros.

Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-08-08 09:44:50 +09:00
Leela Krishna Amudala 5a213a55c6 include/video: move fimd register headers from platform to include/video
This patch moves the contents from regs-fb-v4.h and regs-fb.h to
include/video/samsung_fimd.h. Also updates the header inclusion in
machine files and driver files accordingly.

Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-08-08 09:44:49 +09:00
Manjunathappa, Prakash fb8fa94319 video: da8xx-fb: configure FIFO threshold to reduce underflow errors
Patch works around the below silicon errata:
During LCDC initialization, there is the potential for a FIFO
underflow condition to occur. A FIFO underflow condition
occurs when the input FIFO is completely empty and the LCDC
raster controller logic that drives data to the output pins
attempts to fetch data from the FIFO. When a FIFO underflow
condition occurs, incorrect data will be driven out on the
LCDC data pins.

Software should poll the FUF bit field in the LCD_STAT register
to check if an error condition has occurred or service the
interrupt if FUF_EN is enabled when FUF occurs. If the FUF bit
field has been set to 1, this will indicate an underflow
condition has occurred and then the software should execute a
reset of the LCDC via the LPSC.

This problem may occur if the LCDC FIFO threshold size
(LCDDMA_CTRL[TH_FIFO_READY]) is left at its default value after
reset. Increasing the FIFO threshold size will reduce or
eliminate underflows. Setting the threshold size to 256 double
words or larger is recommended.

Above issue is described in section 2.1.3 of silicon errata
http://www.ti.com/lit/er/sprz313e/sprz313e.pdf

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-07-29 01:11:09 +00:00
Florian Tobias Schandinat d9053b4879 Merge branch 'for-florian' of git://gitorious.org/linux-omap-dss2/linux into fbdev-next
Conflicts:
	drivers/video/omap2/dss/core.c
	drivers/video/omap2/dss/dispc.c
2012-07-25 08:55:46 +00:00
Laurent Pinchart 239921ec1d sh_mobile_meram: Add direct MERAM allocation API
The API can be used to allocate and free MERAM blocks directly, without
going through ICBs.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-07-19 02:05:22 +02:00
Laurent Pinchart 6e729b416b sh_mobile_meram: Use direct function calls for the public API
There's no reason to use abstract operation pointers to implement the
MERAM API. Replace them by direct function calls.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-07-19 02:05:21 +02:00
Laurent Pinchart 4a23717721 sh_mobile_meram: Rename operations to cache_[alloc|free|update]
The MERAM operations meram_register, meram_unregister and meram_update
handle LCDC cache. In preparation for "raw" MERAM allocation, rename
them to more appropriate names.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-07-19 02:05:21 +02:00
Archit Taneja bd5a7b11a0 OMAPDSS: DSI: Fix HSYNC, VSYNC and DE polarities between DISPC and DSI
For DSI operation in videomode, DISPC logic levels for the signals HSYNC, VSYNC
and DE need to be specified to DSI via the fields VP_HSYNC_POL, VP_VSYNC_POL and
VP_DE_POL in DSI_CTRL registers.

This information is completely internal to DSS as logic levels for the above
signals hold no meaning on the DSI bus. Hence a DSI panel driver should be
totally oblivious of these fields.

Fix the logic levels/polarities in the DISPC and DSI registers to a default
value. This is done by overriding these fields in omap_video_timings struct
filled by the panel driver for DISPC, and use the equivalent default values
when programming DSI_CTRL registers. Also, remove the redundant polarity related
fields in omap_dss_dsi_videomode_data.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:15:54 +03:00
Archit Taneja 23c8f88e8a OMAPDSS: Add interlace parameter to omap_video_timings
Add a parameter called interlace which tells whether the timings are in
interlaced or progressive mode. This aligns the omap_video_timings struct with
the Xorg modeline configuration.

It also removes the hack needed to write to divide the manager height by 2 if
the connected interface is VENC.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:15:52 +03:00
Archit Taneja 07fb51c6bd OMAPDSS: Remove omap_panel_config enum from omap_dss_device
omap_panel_config contains fields which are finally written to DISPC_POL_FREQo
registers. These are now held by omap_video_timings and are set when the manager
timings are applied.

Remove the omap_panel_config enum, and remove all it's references from panel or
interface drivers.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:15:51 +03:00
Archit Taneja a8d5e41cef OMAPDSS: Add some new fields to omap_video_timings
Some panel timing related fields are contained in omap_panel_config in the form
of flags. The fields are:

- Hsync logic level
- Vsync logic level
- Data driven on rising/falling edge of pixel clock
- Output enable/Data enable logic level
- HSYNC/VSYNC driven on rising/falling edge of pixel clock

Out of these parameters, Hsync and Vsync logic levels are a part of the timings
in the Xorg modeline configuration. So it makes sense to move the to
omap_video_timings. The rest aren't a part of modeline, but it still makes
sense to move these since they are related to panel timings.

These fields stored in omap_panel_config in dssdev are configured for LCD
panels, and the corresponding LCD managers in the DISPC_POL_FREQo registers.

Add the above fields in omap_video_timings. Represent their state via new enums.

Add these parameters to the omap_video_timings instances in the panel drivers.
Keep the corresponding IVS, IHS, IPC, IEO, RF and ONOFF flags in
omap_panel_config for now. The struct will be removed later.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:15:49 +03:00
Archit Taneja d21f43bc39 OMAPDSS: Remove passive matrix LCD support (part 3)
Remove omap_lcd_display_type enum

The enum omap_lcd_display_type is used to configure the lcd display type in
DISPC. Remove this enum and always set display type to TFT by creating function
dss_mgr_set_lcd_type_tft().

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:15:46 +03:00
Archit Taneja 5ae9eaa6db OMAPDSS: Remove passive matrix LCD support (part 2)
Remove OMAP_DSS_LCD_TFT as a omap_panel_config flag.

We don't support passive matrix displays any more. Remove this flag from all the
panel drivers.

Force the display_type to OMAP_DSS_LCD_DISPLAY_TFT in the interface drivers.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:10:03 +03:00
Chandrabhanu Mahapatra e86d456a23 OMAPDSS: Add LCD3 overlay manager and Clock and IRQ support
The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.

The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-06-29 09:41:24 +03:00
Chandrabhanu Mahapatra ff6331e25e OMAPDSS: Add support for LCD3 channel
OMAP5 Display Subsystem (DSS) architecture comes with a additional LCD3 channel
with its own dedicated overlay manager. The current patch adds LCD3 channel and
basic register support for LCD3 channel. It adds register addresses for various
Display Controller (DISPC) registers like DISPC_DEFAULT_COLOR, DISPC_TIMING_H,
DISPC_DIVISORo, etc.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-06-29 09:41:20 +03:00
Tomi Valkeinen 0df8ad71a2 OMAPDSS: remove enum omap_dss_overlay_managers
We have two almost the same enums: omap_channel and
omap_dss_overlay_managers. omap_channel is used almost everywhere, and
omap_channel assigns explicit values to the enum values which are needed
for proper operation.

omap_dss_overlay_managers is only used in one place, so it's easy to
remove it, which is what this patch does.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-06-28 09:11:28 +03:00
Laurent Pinchart c5deac3c9b fbdev: sh_mobile_lcdc: Implement overlays support
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-06-20 10:02:54 +02:00
Linus Torvalds 804ce9866d fbdev updates for 3.5
It includes:
 - driver for AUO-K1900 and AUO-K1901 epaper controller
 - large updates for OMAP (e.g. decouple HDMI audio and video)
 - some updates for Exynos and SH Mobile
 - various other small fixes and cleanups
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJPyAhmAAoJECSVL5KnPj1PBcoQAIWftuoXo3sk94f5jKcV4Ucx
 MthEc5iEpMVs8xaEruHHNHXWv8ic0x/PfdC2xrpKOEbNXQcNPlb/QE2xWmBRxmT1
 ucDyu10HJ36jKcwcK4ra5IQwOW+GtbTBEoBZT+WNAjxHZtJmxzjQGM4C12zVQpdJ
 +qV2RP93JmsJoVBL9aKVAg1Ko135LLfD8TcKd+z8TmgFnLfSwKhfl7Jtd2xXwyvz
 /hmW3kJUEnD8E5wuj+/g8sKJhQkGalEiITTqG2j2vJyFgxHSqyLSw8BBixrFW1uT
 B9VnZsHF35ccCo+96UZRH4QsGJTx08+rea/qsv8IMSGczyRp5ey1ufjL+CzKiiIN
 FWfex6fY0HHqZGAopQhjag54e914SIbSxdBwWS/iRrtVt3e9d03BzkhYs4rXl4Ey
 CTC5obzWNTbQ6hLEjgWfVKkKcrF56BnRn3zGPgCTKGp2NK3vODdBkt/EmzUFvCWR
 CcyQhh+PvZzEWp3XsdOGossYs/0aP4bO+7XPGJxZaa3+WVcRaZwAG/uZvJXXBfnp
 DGRFy4wPsTTwKYIx4+t/KrsLtNVKioSMS5GEtuM1YEb8pA7mkUIkqwJv1I261h58
 heTr6vWUsviUqHlKALJ+1CdwWGr3CtktCZssGsSUri61nm8CvlSRn2Nr2aJ/L3RN
 AkemC/33RE5X/+lfkdMx
 =tmIU
 -----END PGP SIGNATURE-----

Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6

Pull fbdev updates from Florian Tobias Schandinat:
 - driver for AUO-K1900 and AUO-K1901 epaper controller
 - large updates for OMAP (e.g. decouple HDMI audio and video)
 - some updates for Exynos and SH Mobile
 - various other small fixes and cleanups

* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
  video: bfin_adv7393fb: Fix cleanup code
  video: exynos_dp: reduce delay time when configuring video setting
  video: exynos_dp: move sw reset prioir to enabling sw defined function
  video: exynos_dp: use devm_ functions
  fb: handle NULL pointers in framebuffer release
  OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
  OMAPDSS: Apply VENC timings even if panel is disabled
  OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
  OMAPDSS: DISPC: Support rotation through TILER
  OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
  OMAPFB: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
  OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
  OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
  OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
  drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
  video: exynos mipi dsi: support reverse panel type
  video: exynos mipi dsi: Properly interpret the interrupt source flags
  video: exynos mipi dsi: Avoid races in probe()
  ...
2012-06-01 16:57:51 -07:00
Florian Tobias Schandinat d85d135d8b Omapdss driver changes for 3.5 merge window.
Lots of normal development commits, but perhaps most notable changes are:
 
 * HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
 * Restructure omapdss core driver so that it's possible to implement device
   tree support. This included changing how platform data is passed to the
   drivers, changing display device registration and improving the panel driver's
   ability to configure the underlying video output interface.
 * Basic support for DSI packet interleaving
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPu2LWAAoJEPo9qoy8lh71bo0P/2iTw1WLHiRqOwwXSqOQHm2U
 EFzA4T36qS29h5g9yA1uHnRo2CO7UVL6kOFShk5vzpiBjwZ0e0nPPUxK919hyYEP
 vbrOq4dzdIx4+IYhlFusMKi1OR2JhbmOjE7gx3e1fNby7XxXY2TO2/i98lVKT0bi
 wcJN3cTtXcwZOjApxudIf0J4A/0YRzqGIumnkYKwZWqiW5Rv1+dfb5/Ml5fhYvsH
 IehLQZs8IHtCbM7qw1yDeVAnBUgsuLPCyep3W/zm1MEscboevifw50sFIRwG5GBQ
 cmid+Fi7u3R0/yv/UK2XBGFf7PbeZxWyM5nuZ5raajS/X0mxT1fkGcre1AxNzvgE
 3gjfS9m40WKLpod1hsbXZsX1ksCiBddvT5xkgoiyhfa2G2TDGnOEHmKE4sYuq7qF
 Zc2YuJMahb+iWrPN966Io4PpgscMEjP732b0tg03MtwgR+liajqiuMzA56PDHaTA
 bwwFNS3DVIoEpgeN778PWQJ1mRprlYnK7lyJvpGlrEnDh9tM0Xi/35QDlFl1hvAp
 ZKD9oSkK0cIvZB690J6pRoaVv0PfjHspxFDX28FICTQROV2lJ5P9JOwGi+Bk9FwD
 eBPchUsivnAuhVthp3YwFod5JyN5ZVSD+9Xe9dXUwstRJo9dJMYLY+E41+N4UUS9
 BS2/SKvWqc2NcmIgerO3
 =I8Se
 -----END PGP SIGNATURE-----

Merge tag 'omapdss-for-3.5' of git://github.com/tomba/linux into fbdev-next

Omapdss driver changes for 3.5 merge window.

Lots of normal development commits, but perhaps most notable changes are:

* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
  tree support. This included changing how platform data is passed to the
  drivers, changing display device registration and improving the panel driver's
  ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
2012-05-27 20:58:20 +00:00
Linus Torvalds 9bc747bea5 arm-soc: First batch of cleanups
These cleanups are basically all over the place. The idea is to collect
 changes with minimal impact but large number of changes so we can avoid
 them from distracting in the diffstat in the other series.
 
 A significant number of lines get removed here, in particular because
 the ixp2000 and ixp23xx platforms get removed. These have never been
 extremely popular and have fallen into disuse over time with no active
 maintainer taking care of them. The u5500 soc never made it into a
 product, so we are removing it from the ux500 platform.
 
 Many good cleanups also went into the at91 and omap platforms, as has
 been the case for a number of releases.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPuemiAAoJEIwa5zzehBx3L9oQAKiu0bsCiT6BM3VC5VGpluk7
 YVLH/fkYGdSUTeGrpjeaoxxZnN5M1CLwErg3DxWcyYidy0zfmqitC8t2KQxZMxuf
 bt+hn4flpFnXMNm31B9xBCXOOVAvteZHYS35FdSKGyWo5Kz2WKM8ZrrihkAA7jVi
 U75x4+shFPtIhLNg2sJg4e/9D1T14ypElB7W989NzxMtco5fbukVd6vDBHPlFDG3
 RVI2z2MbWUj3HVmdoyB+09ekruys0MQsbPOGo8D4aeJicrli/JBtL1r1w6ZZ6I8v
 Pe0+CbgemMWS69I37Zuxt35Bejpdofa8nKhT1jBrH4uHYxroKkhhx+VMTtuCcFVw
 Q2DhbbHImiW3598c0jkGi7Gk+TalTxkStMQiO3bqYAHApftdqFUgkpFSnOC/Jxgj
 Y6nUmd+GVPS+r0dDwZg4z5/AnUQd6t8Azp784muPDDxgTV1ZfdaC0LlLjdWesvMO
 x+PQib/U7NdxN5lifV6xCXpPoCQsgshrOkVUQiKVHmzaghm9MXgB8qrzXdTz3dLL
 XtR3+1KmSDTfHPSlTq/9vIN4RJtsKUnDWzNViTElEql36KzT7l5mJnBe6CJWirJh
 7JNyH0p6XDZfc2q7LgdiSU0dv/j9LzBaYUukQCyUI3Tk+5zKgAdKbYNJpRcfPuoO
 BK6OKbjCAoAHL+/nDU2s
 =Hcjs
 -----END PGP SIGNATURE-----

Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull first batch of arm-soc cleanups from Olof Johansson:
 "These cleanups are basically all over the place.  The idea is to
  collect changes with minimal impact but large number of changes so we
  can avoid them from distracting in the diffstat in the other series.

  A significant number of lines get removed here, in particular because
  the ixp2000 and ixp23xx platforms get removed.  These have never been
  extremely popular and have fallen into disuse over time with no active
  maintainer taking care of them.  The u5500 soc never made it into a
  product, so we are removing it from the ux500 platform.

  Many good cleanups also went into the at91 and omap platforms, as has
  been the case for a number of releases."

Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
  ARM: clps711x: Cleanup IRQ handling
  ARM clps711x: Removed unused header mach/time.h
  ARM: clps711x: Added note about support EP731x CPU to Kconfig
  ARM: clps711x: Added missing register definitions
  ARM: clps711x: Used own subarch directory for store header file
  Dove: Fix Section mismatch warnings
  ARM: orion5x: ts78xx debugging changes
  ARM: orion5x: remove PM dependency from ts78xx
  ARM: orion5x: ts78xx fix NAND resource off by one
  ARM: orion5x: ts78xx whitespace cleanups
  Orion5x: Fix Section mismatch warnings
  Orion5x: Fix warning: struct pci_dev declared inside paramter list
  ARM: clps711x: Combine header files into one for clps711x-targets
  ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
  ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
  ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
  ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
  ARM: S5PV210: Use common macro to define resources on dev-audio.c
  ARM: S5PC100: Use common macro to define resources on dev-audio.c
  ARM: S5P64X0: Use common macro to define resources on dev-audio.c
  ...
2012-05-22 09:23:24 -07:00
Chandrabhanu Mahapatra 65e006ff4b OMAPDSS: DISPC: Support rotation through TILER
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.

When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.

The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-22 10:59:15 +03:00
Donghwa Lee 24bb7a6efc video: exynos mipi dsi: support reverse panel type
This patch adds panel_reverse variable to support reversed s6e8ax0 panel
type.

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-05-13 13:08:23 +00:00
Kuninori Morimoto c932b27311 fbdev: sh_mobile_hdmi: add HDMI Control Register support
Latest SuperH HDMI uses not only HDMI Core Register (HTOP0)
but also HDMI Control Register (HTOP1).
This patch adds HDMI Control Register support.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-05-13 13:07:59 +00:00
Kuninori Morimoto db6668d83a fbdev: sh_mobile_hdmi: 32bit register access support
Latest SuperH HDMI allows 32bit access only.
But the data is 8bit. So, we can keep compatibility by switching 8/32 bit access.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-05-13 13:07:59 +00:00
Kuninori Morimoto e0defc8642 fbdev: sh_mobile_hdmi: add interrupt output option
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-05-13 13:07:59 +00:00
Ricardo Neri 9c0b842036 OMAPDSS: Provide an interface for audio support
There exist several display technologies and standards that support audio as
well. Hence, it is relevant to update the DSS device driver to provide an audio
interface that may be used by an audio driver or any other driver interested in
the functionality.

The audio_enable function is intended to prepare the relevant
IP for playback (e.g., enabling an audio FIFO, taking in/out of reset
some IP, enabling companion chips, etc). It is intended to be called before
audio_start. The audio_disable function performs the reverse operation and is
intended to be called after audio_stop.

While a given DSS device driver may support audio, it is possible that for
certain configurations audio is not supported (e.g., an HDMI display using a
VESA video timing). The audio_supported function is intended to query whether
the current configuration of the display supports audio.

The audio_config function is intended to configure all the relevant audio
parameters of the display. In order to make the function independent of any
specific DSS device driver, a struct omap_dss_audio is defined. Its purpose
is to contain all the required parameters for audio configuration. At the
moment, such structure contains pointers to IEC-60958 channel status word and
CEA-861 audio infoframe structures. This should be enough to support HDMI and
DisplayPort, as both are based on CEA-861 and IEC-60958. The omap_dss_audio
structure may be extended in the future if required.

The audio_enable/disable, audio_config and audio_supported functions could be
implemented as functions that may sleep. Hence, they should not be called
while holding a spinlock or a readlock.

The audio_start/audio_stop function is intended to effectively start/stop audio
playback after the configuration has taken place. These functions are designed
to be used in an atomic context. Hence, audio_start should return quickly and be
called only after all the needed resources for audio playback (audio FIFOs,
DMA channels, companion chips, etc) have been enabled to begin data transfers.
audio_stop is designed to only stop the audio transfers. The resources used
for playback are released using audio_disable.

A new enum omap_dss_audio_state is introduced to help the implementations of
the interface to keep track of the audio state. The initial state is _DISABLED;
then, the state transitions to _CONFIGURED, and then, when it is ready to
play audio, to _ENABLED. The state _PLAYING is used when the audio is being
rendered.

Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
2012-05-11 15:13:50 +03:00
Tomi Valkeinen 00928eaf52 OMAPDSS: clean up the omapdss platform data mess
The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:

- Remove struct omap_display_platform_data. It was used just as a
  wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
  dss hwmods do not need the platform data. This should also work better
  for DT, as we can create omapdss device programmatically in generic omap
  boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
  that the dss hwmod drivers can call.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-11 14:44:51 +03:00
Tomi Valkeinen 9b71fb5cbc Merge branch 'for-l-o-3.5'
Conflicts:
	drivers/video/omap2/displays/panel-taal.c

Merge OMAP DSS related board file changes. The branch will also be
merged through linux-omap tree to solve conflicts.
2012-05-10 20:24:14 +03:00
Tomi Valkeinen e4a9e94cc5 OMAPDSS: DSI: implement generic DSI pin config
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.

This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.

The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:

{
	0,	// pin num for clock lane +
	1,	// pin num for clock lane -
	2,	// pin num for data1 lane +
	3,	// pin num for data1 lane -
	...
}

The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2012-05-09 10:53:05 +03:00
Tomi Valkeinen dac8eb5f1d OMAPDSS: TFP410: rename dvi files to tfp410
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2012-05-09 10:51:05 +03:00
Tomi Valkeinen 2e6f2ee7ac OMAPDSS: TFP410: rename dvi -> tfp410
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2012-05-09 10:51:05 +03:00
Tomi Valkeinen e813a55eb9 OMAP: board-files: remove custom PD GPIO handling for DVI output
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2012-05-09 10:51:04 +03:00
Tomi Valkeinen 2da35193dc OMAPDSS: panel-dvi: add PD gpio handling
The driver for the TFP410 chip should handle the power-down signal of
the chip, instead of the current way of handling it in the board files.

This patch adds power_down_gpio into the device's platform data, and
adds the necessary code in the driver to request and handle the GPIO.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-09 10:51:04 +03:00
Jingoo Han 982cfa2f0e video: exynos_dp: fix max loop count in EQ sequence of link training
This patch fixes max loop count in EQ(Channel Equalization) sequence
of link training. According to DP(displayport) specification,
the max loop count in this sequence should be 5.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-05-08 17:00:53 +00:00
Heiko Stübner 2c8304d312 video: auo_k190x: add code shared by controller drivers
The AUO-K190X controllers share a very similar set of commands and
can therefore also share most of the driver code.

Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-04-29 19:35:35 +00:00
Grazvydas Ignotas 4b6430fc98 OMAPDSS: provide default get_timings function for panels
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-04-23 10:48:07 +03:00
Tomi Valkeinen 62c1dcfc74 OMAPDSS: add set_min_bus_tput pointer to omapdss's platform data
omapdss driver needs to use the omap_pm_set_min_bus_tput(), so add a new
entry for that in omapdss's platform data, and set it.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
2012-04-23 10:48:03 +03:00
Geert Uytterhoeven 5c3f968712 m68k/video: Create <asm/vga.h>
For now, it just contains the hack for cirrusfb on Amiga, which is moved
out of <video/vga.h> with some slight modifications (use raw_*() instead of
z_*(), which are defined on all m68k platforms).

This makes it safe to include <video/vga.h> in all contexts. Before it
could fail to compile with

include/video/vga.h: In function ‘vga_mm_r’:
include/video/vga.h:242: error: implicit declaration of function ‘z_readb’
include/video/vga.h: In function ‘vga_mm_w’:
include/video/vga.h:247: error: implicit declaration of function ‘z_writeb’
include/video/vga.h: In function ‘vga_mm_w_fast’:
include/video/vga.h:253: error: implicit declaration of function ‘z_writew’

or

include/video/vga.h:23:21: error: asm/vga.h: No such file or directory

depending on the value of CONFIG_AMIGA.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
2012-04-22 20:16:50 +02:00
Linus Torvalds 9e4db1c3ee Merge branch 'platforms' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM platform updates from Russell King:
 "This covers platform stuff for platforms I have a direct interest in
  (iow, I have the hardware).  Essentially:
   - as we no longer support any other Acorn platforms other than RiscPC
     anymore, we can collect all that code into mach-rpc.
   - convert Acorn expansion card stuff to use IRQ allocation functions,
     and get rid of NO_IRQ from there.
   - cleanups to the ebsa110 platform to move some private stuff out of
     its header files.
   - large amount of SA11x0 updates:
   - conversion of private DMA implementation to DMA engine support
     (this actually gives us greater flexibility in drivers over the old
     API.)
   - re-worked ucb1x00 updates - convert to genirq, remove sa11x0
     dependencies, fix various minor issues
   - move platform specific sa11x0 framebuffer data into platform files
     in arch/arm instead of keeping this in the driver itself
   - update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
     for SIR transmissions as well as FIR
   - rework sa1111 support for genirq, and irq allocation
   - fix sa1111 IRQ support so it works again
   - use sparse IRQ support

  After this, I have one more pull request remaining from my current
  set, which I think is going to be the most problematical as it
  generates 8 conflicts."

Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.

* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
  ARM: 7343/1: sa11x0: convert to sparse IRQ
  ARM: 7342/2: sa1100: prepare for sparse irq conversion
  ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
  ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
  ARM: sa11x0: remove unused DMA controller definitions
  ARM: sa11x0: remove old SoC private DMA driver
  USB: sa1111: add hcd .reset method
  USB: sa1111: add OHCI shutdown methods
  USB: sa1111: reorganize ohci-sa1111.c
  USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
  USB: sa1111: sparse and checkpatch cleanups
  ARM: sa11x0: don't static map sa1111
  ARM: sa1111: use dev_err() rather than printk()
  ARM: sa1111: cleanup sub-device registration and unregistration
  ARM: sa1111: only setup DMA for DMA capable devices
  ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
  ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
  ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
  ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
  ARM: sa1111: delete unused physical GPIO register definitions
  ...
2012-03-27 18:17:02 -07:00
Kuninori Morimoto 8f9c60f2e2 fbdev: sh_mipi_dsi: add extra phyctrl for sh_mipi_dsi_info
sh_mipi uses some clocks, but the method of setup depends on CPU.

Current SuperH (like sh73a0) can control all of these clocks
by CPG (Clock Pulse Generator).
It means we can control it by clock framework only.
But on sh7372, it needs CPG settings AND sh_mipi PHYCTRL::PLLDS,
and only sh7372 has PHYCTRL::PLLDS.

But on current sh_mipi driver, PHYCTRL::PLLDS of sh7372 was
overwrote since the callback timing of clock setting was changed
by c2658b70f0
(fbdev: sh_mipi_dsi: fixup setup timing of sh_mipi_setup()).
To solve this issue, this patch adds extra .phyctrl.

This patch adds detail explanation for unclear mipi settings
and fixup wrong PHYCTRL::PLLDS value for ap4evb (0xb -> 0x6).

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-03-21 07:24:01 +00:00
Laurent Pinchart cdf88b9072 fbdev: sh_mobile_meram: Remove unneeded sanity checks
The meram_register(), meram_unregister() and meram_update() operations
check that the pointers they get from the caller are not NULL. Those
checks can be remove, as the caller already ensures that the pointers
are valid.

The platform sanity checks can also be removed, as the operations can't
be accessed without valid platform data anyway.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:14 +01:00
Laurent Pinchart 97d16fe69b fbdev: sh_mobile_meram: Don't perform update in register operation
Remove the RGB or Y/C base address update from the meram_register()
operation, as this belongs to the meram_update() operation.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:13 +01:00
Laurent Pinchart b5ef967df1 fbdev: sh_mobile_lcdc: Don't store copy of platform data
Instead of copying the whole platform data structure to struct
sh_mobile_lcdc_chan, store a const pointer to the channel platform data.

MERAM configuration information needs to be changed at runtime, so copy
it to struct sh_mobile_lcdc_chan.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:12 +01:00
Laurent Pinchart d81d5fa8ad fbdev: sh_mobile_meram: Remove unused sh_mobile_meram_icb_cfg fields
The marker_icb and cache_icb fields are not used anymore, remove them.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:12 +01:00
Laurent Pinchart 481100506b fbdev: sh_mobile_meram: Allocate ICBs automatically
Instead of manually specifying the ICBs to use in platform data,
allocate them automatically at runtime. The range of reserved ICBs (for
instance to be used through UIO), if any, is passed in the platform data
reserved_icbs field as a bitmask.

The MERAM registration function now returns a pointer to an opaque MERAM
object, which is passed to the update and unregistration functions.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:11 +01:00
Laurent Pinchart 974d250be2 fbdev: sh_mobile_meram: Use genalloc to manage MERAM allocation
Instead of requiring the users to hardcode MERAM allocation in platform
data, allocate blocks at runtime using genalloc.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:10 +01:00
Laurent Pinchart 2a618e0333 fbdev: sh_mobile_meram: Add struct sh_mobile_meram_icb
The new structure stores ICB parameters for ICBs.

Instead of modifying the struct sh_mobile_meram_cfg instances passed by
callers, store the ICB parameters internally and make the public API
take const pointers to sh_mobile_meram_cfg.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:09 +01:00
Laurent Pinchart 05432837ae fbdev: sh_mobile_meram: Make variables unsigned where applicable
Many variables, such as loop counters, sizes and offsets, should be
unsigned integers. Make them so.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:08 +01:00
Laurent Pinchart d272f428fa fbdev: sh_mobile_meram: Add _cfg suffix to struct sh_mobile_meram_icb
The structure describe ICB configuration, no ICB objects themselves.
Rename it to sh_mobile_meram_icb_cfg in preparation for the addition of
an ICB structure.

All the structure fields are unsigned integers, make them so.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:41:08 +01:00
Laurent Pinchart 93ff259846 fbdev: sh_mobile_lcdc: Rename (lcd|num)_cfg (lcd|num)_modes
The struct sh_mobile_lcdc_chan_cfg platform data contains a list of
video modes. Name the lcd_cfg and num_cfg fields to reflect that they
describe video modes.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:55 +01:00
Laurent Pinchart afaad83b9c fbdev: sh_mobile_lcdc: Merge board_cfg and lcd_size_cfg into panel_cfg
Update board code accordingly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:50 +01:00
Laurent Pinchart 43059b0f46 fbdev: sh_mobile_lcdc: Move brightness ops to sh_mobile_lcdc_bl_info
Update board code accordingly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:49 +01:00
Laurent Pinchart 018882aa66 fbdev: sh_mobile_lcdc: Remove board configuration board_data field
The field is unused, remove it. Update board code accordingly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:49 +01:00
Laurent Pinchart aa7b5b0b2d fbdev: sh_mobile_lcdc: Remove board configuration owner field
The field is unused, remove it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:48 +01:00
Laurent Pinchart ca0a0cd798 fbdev: sh_mobile_hdmi: Remove sh_mobile_hdmi_info lcd_chan field
The field is unused, remove it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:48 +01:00
Laurent Pinchart 9a2985e7f9 fbdev: sh_mobile_lcdc: Handle HDMI/MIPI transmitter device directly
Pass a pointer to the transmitter device through platform data, retrieve
the corresponding sh_mobile_lcdc_entity structure in the probe method
and call the transmitter display_on/off methods directly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:45 +01:00
Laurent Pinchart 134d22eb58 sh_mobile_hdmi: Remove platform data lcd_dev field
The field is used to print debug messages only. Remove it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2012-03-12 22:40:44 +01:00
Bernie Thompson 8d21547d3c udlfb: fix hcd_buffer_free panic on unplug/replug
Fix race conditions with unplug/replug behavior, in particular
take care not to hold up USB probe/disconnect for long-running
framebuffer operations and rely on usb to handle teardown.

Fix for kernel panic reported with new F17 multiseat support.

Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
2012-03-01 17:46:27 -08:00
Russell King 086ada54ab FB: sa1100: remove global sa1100fb_.*_power function pointers
Now that we have platform data contained within the individual board
code, we can get rid of the global function pointers, placing them
inside the platform data instead.

Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-02-21 11:56:19 +00:00
Russell King 9e6720fb0c FB: sa1100: move machine inf structures to <video/sa1100fb.h>
Move the LCD data structures to an include file which can be shared
with the board code in arch/arm/mach-sa1100.

Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-02-21 11:56:19 +00:00
Jingoo Han e9474be4eb video: support DP controller driver
Samsung EXYNOS SoC such Exynos5 has DP controller and embedded DP
panel can be used. This patch supports DP driver based on Samsung
EXYNOS SoC chip.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-02-13 03:02:30 +00:00
Donghwa Lee 7258cc14f3 video: support MIPI-DSI controller driver
Samsung S5PC210 and EXYNOS SoC platform has MIPI-DSI controller and
MIPI-DSI based LCD Panel could be used with it.  This patch supports
MIPI-DSI driver based Samsung SoC chip.

LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
machine code and LCD panel driver specific function registered to
mipi_dsim_ddi structure at lcd panel init function called system init.  In
the MIPI-DSI driver, find lcd panel driver by using registered lcd panel
name, and then initialize lcd panel driver.

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-02-13 03:02:03 +00:00
Linus Torvalds 98e9685248 fbdev fixes for 3.3
It includes:
 - a compile fix for fsl-diu-fb
 
 - a fix for a suspend/resume issue in atmel_lcdfb
 
 - a fix for a suspend/resume issue in OMAP
 
 - a workaround for a hardware bug to avoid physical damage in OMAP
 
 - a really trivial dead code removal in intelfb
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJPMG54AAoJECSVL5KnPj1PR6QQAKOoD4luFRw2F85jdk4GYBiX
 WqUWc1OlKYxCGIhk6LpV6fwBLDZCTjOw9NU/9i3JIOHAscGzqVvUce1zYwolEu0B
 tTH15/6Bh6uuRJEKYF8H53t1vsbrutssvUsqVcJsHrfie6bVjqjGV18cLT9siVy5
 jEZnU958Nb7t8hk7Af1ppQkbB4cpExHX4k3hXTKM+dOkRWMaH1fHv2dnikKuYXDq
 G7PC57VqN89DP14M+isUGt5uUgaMSmI09VdTYZ8xgULaZwOxnfOQNnceb/AaKnTY
 I2oHDNlNwmiHVgafN7uS0tAhIqnlYOAVLJNLlDfL7xC71AyH6WtzwJuhXnqun7v6
 moSwzzGKHohCXyeTjMAthx6HyLq55fBPAI1CmEEtmFLMv1tADLAp9Rm4dsaAjyF8
 7aKJO/9iGEpolLYjAGJGGjgCALa+/NWdXnW/zP/2vmcjAaPOZtd0YlD3OaPYr31p
 0cImhG57xIAfh60BRq+/FDthEN478Xj8f2jRe/2nsonw8JuFodZZ6nUaFeQS25X/
 X/07Wkvmz2CY8FoPeXDHaKO8B1wJphzvY2iJjDwI1jg8u/PT2agILNM24tH3SVky
 s6nyBLOEBHZh7mVwll2YifjZ6zzJm4y09LzgZpqXmUXOYPDn5JP9yZE4+R23RaEY
 kVz8fkE/FjmjAlx/WjKa
 =2uP4
 -----END PGP SIGNATURE-----

Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6

fbdev fixes for 3.3

It includes:
 - compile fix for fsl-diu-fb
 - fix for a suspend/resume issue in atmel_lcdfb
 - fix for a suspend/resume issue in OMAP
 - workaround for a hardware bug to avoid physical damage in OMAP
 - really trivial dead code removal in intelfb

* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
  atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
  intelfb: remove some dead code
  drivers/video: compile fixes for fsl-diu-fb.c
  OMAPDSS: HDMI: PHY burnout fix
  OMAP: 4430SDP/Panda: add HDMI HPD gpio
  OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
  OMAPDSS: remove wrong HDMI HPD muxing
  OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
  OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
  OMAPDSS: use sync versions of pm_runtime_put
2012-02-07 15:54:02 -08:00
Florian Tobias Schandinat b20f86625d Merge commit 'v3.3-rc1' into fbdev-next 2012-01-28 19:52:40 +00:00
Tomi Valkeinen c49d005b6c OMAPDSS: HDMI: PHY burnout fix
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.

This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.

The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.

The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-26 13:51:36 +02:00
Linus Torvalds dca88ad691 Merge branch 'for-next' of git://git.infradead.org/users/dhowells/linux-headers
* 'for-next' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: Split trivial #if defined(__KERNEL__) && X conditionals
  UAPI: Don't have a #elif clause in a __KERNEL__ guard in linux/soundcard.h
  UAPI: Fix AHZ multiple inclusion when __KERNEL__ is removed
  UAPI: Make linux/patchkey.h easier to parse
  UAPI: Fix nested __KERNEL__ guards in video/edid.h
  UAPI: Alter the S390 asm include guards to be recognisable by the UAPI splitter
  UAPI: Guard linux/cuda.h
  UAPI: Guard linux/pmu.h
  UAPI: Guard linux/isdn_divertif.h
  UAPI: Guard linux/sound.h
  UAPI: Rearrange definition of HZ in asm-generic/param.h
  UAPI: Make FRV use asm-generic/param.h
  UAPI: Make M32R use asm-generic/param.h
  UAPI: Make MN10300 use asm-generic/param.h
  UAPI: elf_read_implies_exec() is a kernel-only feature - so hide from userspace
  UAPI: Don't include linux/compat.h in sparc's asm/siginfo.h
  UAPI: Fix arch/mips/include/asm/Kbuild to have separate header-y lines
2012-01-14 18:03:30 -08:00
Florian Tobias Schandinat 193984f43d Merge branch 'for-florian' of git://gitorious.org/linux-omap-dss2/linux into fbdev-next 2012-01-08 15:30:34 +00:00
Mythri P K 9a9016832d OMAPDSS: HDMI: Disable DDC internal pull up
Disables the internal pull resistor for SDA and SCL which are enabled by
default, as there are external pull up's in 4460 and 4430 ES2.3
SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure.

Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-05 10:34:50 +02:00
Mythri P K ee9dfd82ff OMAPDSS: HDMI: Move duplicate code from boardfile
Move duplicate HDMI mux_init code from omap4 and panda board file
to display file.

Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-05 10:34:49 +02:00
Laurent Pinchart edd153a3e4 fbdev: sh_mobile_lcdc: Support FOURCC-based format API
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-12-19 20:07:13 +00:00
Florian Tobias Schandinat a4581b35e1 Merge commit 'v3.2-rc6' into fbdev-next 2011-12-17 22:00:49 +00:00
David Howells e9356f4da3 UAPI: Fix nested __KERNEL__ guards in video/edid.h
Fix nested __KERNEL__ guards in video/edid.h to make parsing easier.

Signed-off-by: David Howells <dhowells@redhat.com>
2011-12-13 09:26:45 +00:00
Tomi Valkeinen 9d11c321a8 OMAPDSS: Add comments about blocking of ovl/mgr functions
Add comments specifying what ovl/mgr functions may block.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:52 +02:00
Tomi Valkeinen ff4733dcf5 OMAPDSS: APPLY: remove device_changed field
omap_overlay_manager contains device_changed field, which no longer has
any use. So remove the field and the few places where it is touched.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:49 +02:00
Tomi Valkeinen 5d5a97a6fb OMAPDSS: APPLY: move channel-field to extra_info set
Setting overlay's output channel is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the channel
affects two managers.

This patch moves the channel field into the "extra_info" set, handled
together with enabled-status.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:47 +02:00
Tomi Valkeinen c1a9febfaf OMAPDSS: APPLY: move ovl->info to apply.c
struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.

This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:47 +02:00
Tomi Valkeinen 388c4c6cbb OMAPDSS: APPLY: move mgr->info to apply.c
struct omap_overlay_manager contains info and info_dirty fields, both of
which should be internal to apply.c.

This patch moves those fields into mgr_priv data, and names them
user_info and user_info_dirty.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:46 +02:00
Tomi Valkeinen aaa874a985 OMAPDSS: APPLY: rewrite overlay enable/disable
Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().

This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.

This patch achieves that by doing the following things:

1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.

2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.

3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.

The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.

This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:44 +02:00
Tomi Valkeinen bf213523fe OMAPDSS: APPLY: move mgr->enabled to mgr_priv_data
struct omap_overlay_manager contains "enabled"-field, used to track if
the manager is enabled or not. This field should be internal to apply.c.

This patch moves the field to mgr_priv_data, and applies the necessary
locking when accessing the field.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:43 +02:00
Tomi Valkeinen 9a147a65de OMAPDSS: DSI: call mgr_enable/disable for cmd mode displays
The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.

However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.

This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:42 +02:00
Tomi Valkeinen 07e327c9c1 OMAPDSS: store overlays in a list for each manager
Current way of handling overlay-manager links is a bit strange: each
manager has a static array, containing pointers to all the overlays
(even those used by other managers). The overlays contain a pointer to
the manager being used.

This patch makes the system a bit saner: each manager has a linked list
of overlays, and only the overlays linked to that manager are in the
list.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:35 +02:00
Tomi Valkeinen 5617ad0979 OMAPDSS: store managers in an array
Overlay managers are stored in a linked list. There's no need for this
list, as an array would do just as fine.

This patch changes the code to use an array for overlay managers.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:34 +02:00
Tomi Valkeinen be729178f0 OMAPDSS: APPLY: track whether a manager is enabled
Add "enabled" field to struct omap_overlay_manager, which tells if the
output is enabled or not. This will be used in apply.c in the following
patches.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:31 +02:00
Tomi Valkeinen 7797c6da64 OMAPDSS: hide manager's enable/disable()
omap_overlay_manager struct contains enable() and disable() functions.
However, these are only meant to be used from inside omapdss, and thus
it's bad to expose the functions.

This patch adds dss_mgr_enable() and dss_mgr_disable() functions to
apply.c, which handle enabling and disabling the output.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:31 +02:00
Tomi Valkeinen 5476e74a03 OMAPDSS: remove partial update from DSI
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
  be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex

Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.

This patch removes the partial update from the dsi.c.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:23 +02:00
Kuninori Morimoto a2e6297153 fbdev: sh_mipi_dsi: add HSxxCLK support
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-11-21 23:43:22 +00:00
Kuninori Morimoto 5e47431aab fbdev: sh_mipi_dsi: add set_dot_clock() for each platform
Dot clock of SH MIPI are depends on each platform board.
This patch adds set_dot_clock() function for it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-11-21 23:43:21 +00:00
Kuninori Morimoto f832906a56 fbdev: sh_mipi_dsi: add sync_pulses/sync_events/burst mode
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-11-21 23:43:21 +00:00
Kuninori Morimoto 26c3d7ac21 fbdev: sh_mipi_dsi: add lane control support
SH MIPI DSI can use 0-4 lane

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-11-21 23:43:21 +00:00
Kuninori Morimoto d07a9d2a5e fbdev: sh_mipi_dsi: add SH_MIPI_DSI_BL2E flag
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-11-21 23:43:21 +00:00
Kuninori Morimoto f7b0af68bc fbdev: sh_mipi_dsi: add SH_MIPI_DSI_HFPBM flag
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-11-21 23:43:21 +00:00
Kuninori Morimoto 32ba95c69f fbdev: sh_mipi_dsi: typo fix of SH_MIPI_DSI_HBPBM
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-11-21 23:43:20 +00:00
Tomi Valkeinen 13662dc5b1 ARM: OMAP: HWMOD: Unify DSS resets for OMAPs
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.

The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.

This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.

The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
 unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-11-08 03:16:13 -07:00
Florian Tobias Schandinat ef26b7943c Merge branch 'for-florian' of git://gitorious.org/linux-omap-dss2/linux into fbdev-next 2011-10-15 00:19:52 +00:00
Archit Taneja 54128701ec OMAPDSS: DISPC: zorder support for DSS overlays
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.

Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.

Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03 16:51:55 +03:00
Archit Taneja b8c095b4d6 OMAPDSS: DISPC: VIDEO3 pipeline support
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03 16:51:54 +03:00
Archit Taneja 11354dd58d OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.

Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.

Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.

Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.

Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03 16:51:54 +03:00
Tomi Valkeinen 212b0d50e2 OMAPDSS: remove vaddr from overlay info
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.

This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:32 +03:00
Tomi Valkeinen 562a060611 OMAPDSS: Add N800 panel driver
This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).

That said, the new driver works fine for basic use.

Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:30 +03:00
Tomi Valkeinen bb36dbfd23 OMAPDSS: Taal: remove external backlight support
Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.

The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.

This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:27 +03:00
Tomi Valkeinen ba2eac9ed3 OMAP: DSS2: add panel-dvi driver
We have currently panel-generic-dpi driver, which is a combined driver
for dummy panels and also for DVI output.

The aim is to split the panel-generic-dpi into two, one for fixed size
dummy panels connected via DPI, and the other (this) for variable
resolution output which supports DDC channel (in practice a DVI framer
chip connected to DPI output).

Original i2c code by: Ricardo Salveti de Araujo
<ricardo.salveti@canonical.com>

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:48 +03:00
Tomi Valkeinen df4769c9c4 OMAP: DSS2: add detect() to omap_dss_driver struct
detect() can be used to probe if the display is connected.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:44 +03:00
Tomi Valkeinen 3d5e0ef746 OMAP: DSS2: add read_edid() to omap_dss_driver struct
read_edid() can be used to get the EDID information from the display.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:44 +03:00
Tomi Valkeinen 7f6f3c4bf3 OMAP: DSS2: DISPC: Add missing IRQ definitions
Add IRQ definitions for missing OMAP4 IRQs: FRAMEDONEWB, FRAMEDONETV,
WBBUFFEROVERFLOW.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:42 +03:00
Tomi Valkeinen c90a78ecc2 OMAP: DSS2: DSI: Add comment about regn
regn divider is one greater than the REGN divider in TRM. Add a comment
to point this out.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:41 +03:00
Tomi Valkeinen b44e45825d OMAP: DSS2: HDMI: change regn definition
regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.

To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.

This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:41 +03:00
Archit Taneja 8af6ff0107 OMAP: DSS2: DSI Video mode support
Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
  omap_dss_device struct. This allows panel driver to configure dsi video_mode
  specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
  TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
  enable/disable video mode for a given virtual channel and a given pixel format
  type.

Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required  for command mode interleaving.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:30 +03:00
Archit Taneja a3b3cc2b88 OMAP: DSS2: Create an enum for DSI pixel formats
Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.

This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.

Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.

Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:29 +03:00
Archit Taneja b3b89c05cb OMAP: DSS2: DSI: Introduce generic read functions
Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.

Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.

Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:28 +03:00
Archit Taneja 5c716a04ed OMAP: DSS2: DSI: Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2()
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:27 +03:00
Archit Taneja 6ff8aa3182 OMAP: DSS2: DSI: Introduce generic write functions
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.

Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:26 +03:00
Archit Taneja 7e951ee995 OMAP: DSS2: Create enum for DSI operation modes
Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:26 +03:00
Tomi Valkeinen f6dc815098 OMAP: DSS2: Add GLOBAL_ALPHA & PRE_MULT_ALPHA to ovl caps
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.

Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
2011-09-30 16:16:21 +03:00
Tomi Valkeinen 4a9e78abb7 OMAP: DSS2: Remove support for non-DISPC overlays
Remove support for non-DISPC overlays and overlay managers.

The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:

- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
  update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
  omapdss driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
2011-09-30 16:16:20 +03:00
Tomi Valkeinen 8fa8031c54 OMAP: DSS2: Handle manager change in apply
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.

Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().

A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:19 +03:00
Tomi Valkeinen 5bc416cba1 OMAP: DSS2: DSI: Improve dsi_mux_pads parameters
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:17 +03:00
Mayuresh Janorkar 24305db864 OMAP: DSS2: Add picodlp panel driver
PicoDLP is a micro projector from TI.

DLP used in OMAP4 is dpp2600 (DLP Pico Projector) The DLP requires
commands to be sent over i2c for configurations. To know more about
dpp2600 commands please visit:
https://focus.ti.com/myti/docs/extranet.tsp?sectionId=403

The picodlp module consists of a dss driver and an i2c_client.

To know more please visit:
http://www.omappedia.org/wiki/PicoDLP_projector_guide

Based on original design from Mythri P K <mythripk@ti.com>

Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: squashed commits]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-14 18:08:23 +03:00
Florian Tobias Schandinat 8edbeb6eea Merge branch 'sh-mobile-lcdc' of git://linuxtv.org/pinchartl/fbdev into fbdev-next 2011-08-30 20:02:02 +00:00
Bernie Thompson 58e7c3b001 udlfb: add more comprehensive support for DPMS FB_BLANK_* modes
Fixes earlier problems where monitor would not return from blank

Test with any DisplayLink-based USB 2.0 graphics adapter
sudo nano /sys/class/graphics/fb?/blank
and write out single digit FB_BLANK_* code from include/linux/fb.h

Supports on (0), blank (1), suspend (2,3), powerdown (4)

Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-08-24 10:07:59 +00:00
Laurent Pinchart ce1c0b0873 fbdev: sh_mobile_lcdc: Replace hardcoded register values with macros
Instead of hardcoding register values through the driver, define macros
for individual register bits using the register name and the bit name,
and use the macros.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2011-08-19 08:22:37 +02:00
Tomi Valkeinen aea4eb9590 OMAP: DSS2: Remove unused opt_clock_available
opt_clock_available() is no longer needed, so remove it.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:22:05 +03:00
Tomi Valkeinen aac927c93b OMAP: DSS2: rewrite use of context_loss_count
The function to get device's context loss count has changed from

omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()

Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.

Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:08:15 +03:00
Tomi Valkeinen 3c07cae2cc OMAP: DSS2: Add Color Phase Rotation support
Add Color Phase Rotation (CPR) support and sysfs files to enable CPR and
to set the CPR coefficient matrix.

CPR is enabled via manager?/cpr_enable file, and the coefficient matrix
is set via manager?/cpr_coef file. The values in cpr_coef are in the
following order:

RR RG RB GR GG GB BR BG BB

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01 12:07:13 +03:00
Tomi Valkeinen 8cff88c5da OMAP: DSS2: remove update_mode from omapdss
Remove the whole update_mode stuff from omapdss driver. If automatic
update for manual update displays is needed, it's better implemented in
higher layers.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01 12:01:15 +03:00
Tomi Valkeinen 24e6289c02 OMAP: DSS2: remove extra includes from include/video/omapdss.h
omapdss.h included platform_device.h and atomic.h, neither of which is
needed by omapdss.h. Remove those includes from omapdss.h, and fix the
affected .c files which did not include platform_device.h even though
they should.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01 12:01:12 +03:00
Paul Mundt d15660a1e6 Merge branches 'common/fbdev' and 'common/fbdev-meram' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6 2011-05-24 15:49:57 +09:00
Paul Mundt a6b5825aa7 Merge branch 'for-paul' of git://gitorious.org/linux-omap-dss2/linux
Conflicts:
	drivers/video/omap2/dss/dsi.c
	drivers/video/omap2/dss/dss_features.c
	drivers/video/omap2/dss/dss_features.h

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-05-24 15:35:54 +09:00
Damian 3fedd2ac76 sh_mobile_meram: Add support for NV24 framebuffers
Since the NV24 framebuffer has a CbCr plane that is twice as wide
as the Y plane, it needs to be handled as a special case.

Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-05-23 16:06:26 +09:00
Damian 7caa4342ca sh_mobile_meram: MERAM framework for LCDC
Based on the patch by Takanari Hayama <taki@igel.co.jp>

Adds support framework necessary to use Media RAM (MERAM)
caching functionality with the LCDC.  The MERAM is accessed
through up to 4 Interconnect Buffers (ICBs).

ICB numbers and MERAM address ranges to use are specified in
by filling in the .meram_cfg member of the LCDC platform data

Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-05-23 16:06:24 +09:00
Amber Jain 0d66cbb53e OMAP: DSS2: Add support for NV12 format
Add the support for NV12 color format.
Configure base address for UV component of NV12 color format.
Change the way chroma scaling is handled for YUV formats on OMAP4 by enabling
chroma-resampling for video pipeline and hence using FIR2 register set for
scaling UV.
Changes to _dispc_set_scaling(), because of the reason above, are:
- call _dispc_set_scaling_common() to handle scaling for all color formats
  except for OMAP4 where it only handles scaling for RGB or Y-component
- call _dispc_set_scaling_uv() for special handling required for UV
  component on OMAP4.
- dispc_set_scaling_uv() also resets chroma-resampling bit for RGB color modes.

Contains chroma scaling (_dispc_set_scaling_uv) design and implemented by
Lajos Molnar <molnar@ti.com>

Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23 08:29:47 +03:00
Amber Jain f20e42205a OMAP: DSS2: Add new color formats for OMAP4
Add new color formats supported by OMAP4: NV12, RGBA16, RGBX16,
ARGB16_1555, XRGB16_1555.
NV12 color format is defined here, its support in DSS will be added separately.

Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23 08:29:47 +03:00
Archit Taneja 75d7247c07 OMAP: DSS2: DSI: Get number of DSI data lanes using DSI_GNQ register
On OMAP3, the DSI module has 2 data lanes. On OMAP4, DSI1 has 4 data lanes
and DSI2 has 2 data lanes. Introduce function dsi_get_num_data_lanes() which
returns the number of data lanes on the dsi interface, introduce function
dsi_get_num_data_lanes_dssdev() which returns the number of data lanes used by
the omap_dss_device connected to the lanes.

Use the DSI_GNQ register on OMAP4 to get the number of data lanes, modify
dsi.c to use the number of lanes and the extra data lanes on DSI1.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-16 13:31:09 +03:00
Tomi Valkeinen 1d5952a868 OMAP: DSS2: RFBI: add omap_rfbi_configure
Add omap_rfbi_configure() which the panel driver can use to reconfigure
the data element size and the number of data lines in the RFBI bus.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12 19:39:50 +03:00
Tomi Valkeinen 773139f175 OMAP: DSS2: RFBI: add rfbi_bus_lock
Add similar bus lock to RFBI as is in DSI. The panel driver can use the
bus lock to mark that the RFBI bus is currently in use.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12 19:39:49 +03:00
Archit Taneja 5a8b572d83 OMAP4: DSS2: DSI: Changes for DSI2 on OMAP4
Introduce DSI2 PLL clock sources needed by LCD2 channel and DSI2 Protocol
engine and DISPC Functional clock. Do the following:

- Modify dss_get_dsi_clk_source() and dss_select_dsi_clk_source() to take the
  dsi module number as an argument.
- Create debugfs files for dsi2, split the corresponding debugfs functions.
- Allow DPI to use these new clock sources.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12 19:30:27 +03:00
Archit Taneja a72b64b999 OMAP: DSS2: Pass platform_device as an argument in dsi functions
The DSI interface is represented as a platform device, using the DSI platform
driver(dsi.c). The current DSI driver design is capable of running only one
instance of a DSI device. On OMAP4, there are 2 very similar DSI modules which
can be represented as instances of "omapdss_dsi" platform device.

Add member "module" in "dssdev.phy.dsi" that tells us which DSI module's lanes
the panel is connected to. Modify dsi.c functions to take the device's
platform_device struct pointer, provide functions dsi_get_dsidev_from_dssdev()
and dsi_get_dsidev_from_id() take the panel's omap_dss_device and module number
respectively, and return the platform_device pointer. Currently, the dsi struct
is declared globally and is accessed when dsi data is needed. The new pdev
argument will be used later to provide the platform device's dsi related data.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12 19:30:26 +03:00
Archit Taneja 1ffefe755c OMAP: DSS2: DSI: Add extra omap_dss_device argument in functions exported by dsi
Add pointer to omap_dss_device struct as an argument in the functions which
are exported to dsi panel drivers. This argument will tell the DSI driver
which DSI interface's data it has to choose.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12 19:30:26 +03:00
Tomi Valkeinen 1abf781454 OMAP: DSS2: Taal: Implement ULPS functionality
ULPS is a low power state where the DSI lanes are kept at ground. This
patch implements ULPS by having a DSI bus inactivity timer which
triggers the entry to ULPS. ULPS exit will happen automatically when the
driver needs to do something on the DSI lanes.

The ulps_timeout is configurable from board file or via sysfs.
Additionally another sysfs file, "ulps", can be used to check the
current ULPS state, or to manually enter or exit ULPS.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:48 +03:00
Tomi Valkeinen 33a410be6f OMAP: DSS2: Taal: Implement configurable ESD interval
ESD check in Taal driver is currently on/off feature with hardcoded
interval. This patch changes it to a configurable interval, which can be
set from the board file.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:44 +03:00
Tomi Valkeinen d1f5857e4b OMAP: DSS2: DSI: Add DSI pad muxing support
Add dsi_mux_pads function pointer to omap_dss_board_info, and use the
function pointer in DSI code to configure the DSI pads either to normal
DSI operation, or to pull down when in ULPS.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:17 +03:00
Tomi Valkeinen 22d6d67626 OMAP: DSS2: DSI: add parameter to enter ulps on disable
Add parameter to omapdss_dsi_display_disable() which the panel driver
can use to tell if the DSI lanes should be put to ULPS before disabling
the interface.

This can be used to skip ULPS entry in cases where the panel doesn't
care about ULPS state, for example when the panel will be reset, or when
the display interface will be enabled again right after the disable.

This will speed up the operation considerably in cases where entering
ULPS would fail with timeout, and the panel driver isn't even interested
in entering ULPS.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:17 +03:00
Tomi Valkeinen 2a89dc1533 OMAP: DSS2: DSI: add option to leave DSI lanes powered on
The DSI pins are powered by VDDS_DSI. If VDDS_DSI is off, the DSI pins
are floating even if they are pinmuxed to, say, safe mode and there's a
pull down/up.

This patch gives the panel drivers an option to leave the VDDS_DSI power
enabled while the DSS itself is turned off. This can be used to keep the
DSI lanes in a valid state while DSS is off, if the DSI pins are muxed
for pull down (not done in this patch).

There will be a slight power consumption increase (~100 uA?) when the
VDDS_DSI is left on, but because this option is used when the panel is
left on, the regulator consumption is negligible compared to panel power
consumption.

When the panel is fully turned off the VDDS_DSI is also turned off.

As an added bonus this will give us faster start up time when starting
up the DSS and the regulator is already enabled.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:13 +03:00
Archit Taneja 6cb07b256a OMAP: DSS2: HDMI: Use dss_device clock configuration for HDMI PLL parameters
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:10 +03:00
Archit Taneja e888166247 OMAP2PLUS: DSS2: Add clock sources to dss device clock configuration
Add enum dss_clock_source in dssdev.clocks struct so that the clock sources can
be specified in the board file.
Replace hard coded clock sources in dsi.c, dpi.c and replace them with the new
clock source members in dssdev.clocks. Modify the sdp4430_lcd_device struct in
board-4430sdp.c to specify clock sources for DISPC_FCLK, LCD1_CLK and DSI1_FCLK.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:06 +03:00
Archit Taneja 89a35e5170 OMAP2PLUS: DSS2: Change enum "dss_clk_source" to "omap_dss_clk_source"
Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:19:27 +03:00
Tomi Valkeinen 06b2b0d597 OMAP: DSS2: make omap_dss_(un)register_device static
omap_dss_register_device and omap_dss_unregister_device can only be
called from core.c, so we can make it static.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:19:26 +03:00
Jani Nikula 7a0987bf2c OMAP: DSS2: Add method for querying display dimensions from DSS drivers
Add get_dimensions() to struct omap_dss_driver. Use the call, if supported
by the driver, in OMAPFB.

Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:19:24 +03:00
Tomi Valkeinen c6940a3dc5 OMAP: DSS2: move dss device clock configuration
Clock configuration was defined inside dssdev.phy.dsi struct. The clock
config doesn't really belong there, and so it's moved to dssdev.clock
struct.

Now the explicit clock configuration could also be used for other
interfaces than DSI, although there's no support for it currently.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:19:16 +03:00
Tomi Valkeinen 4e9f99d75c OMAP: DSS2: Move nokia-dsi-panel.h to include/video/
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the
OMAP DSS panel driver for Nokia's DSI displays. A more logical place for
it is in include/video.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:10:07 +03:00
Tomi Valkeinen f8ae2f08d2 OMAP: DSS2: Move panel-generic-dpi.h to include/video/
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:08:51 +03:00
Tomi Valkeinen a0b38cc4d3 OMAP: DSS2: Move display.h to include/video/
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:05:07 +03:00
Jiri Kosina 07f9479a40 Merge branch 'master' into for-next
Fast-forwarded to current state of Linus' tree as there are patches to be
applied for files that didn't exist on the old branch.
2011-04-26 10:22:59 +02:00
Justin P. Mattock 79add62773 update David Miller's old email address
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-04-06 06:19:38 -07:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Andreas Bießmann 7cdcdb69bd atmel_lcdfb: implement inverted contrast pwm
This patch introduces lcdc->lcdcon_pol_negative which set CONTRAST_CTR
 register to inverted polarity.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-03-22 16:23:44 +09:00
Damian Hobson-Garcia 53b5031430 fbdev: sh_mobile_lcdc: Add YUV framebuffer support
Supports YCbCr420sp, YCbCr422sp, and YCbCr44sp, formats
(bpp = 12, 16, and 24) respectively.

When double-buffering both Y planes appear before the C planes (Y-Y-C-C),
as opposed to  Y-C-Y-C.

Set .nonstd in struct sh_mobile_lcdc_chan_cfg to enable YUV mode, and use
.bpp to distiguish between the 3 modes.
The value of .nonstd is copied to bits 16-31 of LDDFR in the LCDC and
should be set accordingly.
.nonstd must be set to 0 for RGB mode.

Due to the encoding of YUV data, the framebuffer will clear to green
instead of black.

In YUV 420 mode, panning is only possible in 2 line increments.
Additionally in YUV 420 mode the vertical resolution of the framebuffer
must be an even number.

Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-03-16 17:27:10 +09:00
Alexandre Courbot 3b0fd9d755 fbdev: sh_mobile_lcdcfb: add backlight support
Support for backlight devices controlled through board-specific
routines. Backlights can be defined per-channel and follow fbdev
directives to switch off as the LCD blanks or is turned on/off.

Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-03-10 20:20:57 +09:00
Paul Mundt ca9c20ce2b Merge branch 'fbdev/udlfb' 2011-01-06 18:10:09 +09:00
Paul Mundt 81f6f3c104 video: udlfb: Kill off special printk wrappers, use pr_fmt().
This kills off all of the dl_xxx() printk wrappers and simply stubs in a
pr_fmt() definition to accomplish the same thing.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-01-06 18:07:54 +09:00
Paul Mundt b9f03a3cd0 video: udlfb: Kill off some magic constants for EDID sizing.
The edid length is fixed, so use the standard definition consistently.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-01-06 18:04:02 +09:00
Paul Mundt 97cbc8fb1e Merge branch 'common/fbdev-mipi' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6 2011-01-05 17:30:20 +09:00
Guennadi Liakhovetski 38f3a87942 fbdev: sh_mipi_dsi: support different register layouts
The register layout of the MIPI DSI unit on sh-mobile SoCs differ. Add platform
parameters to support such variations.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-01-05 17:16:24 +09:00
Paul Mundt 7ccbefe07e Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 2010-12-22 12:56:10 +09:00
Andres Salomon 521bc83b0f s1d13xxxfb: drop unused code
Silence warnings such as -

drivers/video/s1d13xxxfb.c:421: warning: ‘bltbit_wait_bitset’ defined but not used

Just drop the unused code.

Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-12-21 01:05:43 +09:00
Paul Mundt 96f8d864af fbdev: move udlfb out of staging.
udlfb has undergone a fair bit of cleanup recently and is effectively at
the point where it can be liberated from staging purgatory and promoted
to a real driver.

The outstanding cleanups are all minor, with some of them dependent on
drivers/video headers, so these will be done incrementally from udlfb's
new home.

Requested-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-11-16 14:00:24 +09:00
Mike Frysinger e3a4d1d2de fbdev: da8xx: punt duplicated FBIO_WAITFORVSYNC define
This is already defined by linux/fb.h now, so punt the duplicate
definition from the driver header.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-11-16 10:14:22 +09:00
Guennadi Liakhovetski c36940e678 fbdev: sh_mobile_hdmi: add support for more precise HDMI clock configuration
The HDMI clock has to be reconfigured for different video modes. However, the
precision of the supplying SoC clock on SH-Mobile systems is often
insufficient. This patch allows to additionally reconfigure the parent clock
to achieve the optimal HDMI clock frequency, in case this is supported by the
platform.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-11-10 17:23:54 +09:00
Russell King b3773301c4 Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/genesis-2.6 into devel-stable
Conflicts:
	drivers/video/sh_mobile_hdmi.c
2010-10-28 20:14:38 +01:00
Linus Torvalds 33081adf8b Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
  ALSA: hda - Disable sticky PCM stream assignment for AD codecs
  ALSA: usb - Creative USB X-Fi volume knob support
  ALSA: ca0106: Use card specific dac id for mute controls.
  ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
  ALSA: ca0106: Create a nice spot for mapping channels to dacs.
  ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
  ALSA: ca0106: Pull out dac powering routine into separate function.
  ALSA: ca0106 - add Sound Blaster 5.1vx info.
  ASoC: tlv320dac33: Use usleep_range for delays
  ALSA: usb-audio: add Novation Launchpad support
  ALSA: hda - Add workarounds for CT-IBG controllers
  ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
  ASoC: tpa6130a2: Error handling for broken chip
  ASoC: max98088: Staticise m98088_eq_band
  ASoC: soc-core: Fix codec->name memory leak
  ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
  ALSA: hda - Add some workarounds for Creative IBG
  ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
  ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
  ALSA: hda - Add alc_init_jacks() call to other codecs
  ...
2010-10-25 08:32:05 -07:00
Linus Torvalds 229aebb873 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  Update broken web addresses in arch directory.
  Update broken web addresses in the kernel.
  Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget
  Revert "Fix typo: configuation => configuration" partially
  ida: document IDA_BITMAP_LONGS calculation
  ext2: fix a typo on comment in ext2/inode.c
  drivers/scsi: Remove unnecessary casts of private_data
  drivers/s390: Remove unnecessary casts of private_data
  net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data
  drivers/infiniband: Remove unnecessary casts of private_data
  drivers/gpu/drm: Remove unnecessary casts of private_data
  kernel/pm_qos_params.c: Remove unnecessary casts of private_data
  fs/ecryptfs: Remove unnecessary casts of private_data
  fs/seq_file.c: Remove unnecessary casts of private_data
  arm: uengine.c: remove C99 comments
  arm: scoop.c: remove C99 comments
  Fix typo configue => configure in comments
  Fix typo: configuation => configuration
  Fix typo interrest[ing|ed] => interest[ing|ed]
  Fix various typos of valid in comments
  ...

Fix up trivial conflicts in:
	drivers/char/ipmi/ipmi_si_intf.c
	drivers/usb/gadget/rndis.c
	net/irda/irnet/irnet_ppp.c
2010-10-24 13:41:39 -07:00
Guennadi Liakhovetski 6de9edd5bd fbdev: sh_mobile_hdmi: implement locking
The SH-Mobile HDMI driver runs in several contexts: ISR, delayed work-queue,
task context, when called from the sh_mobile_lcdc framebuffer driver. This
creates ample race possibilities. Even though most these races are purely
theoretical, it is better to close them. To trace fb_info validity we install a
notification callback in the HDMI driver, and the only way for it to get to
driver internal data is by using struct sh_mobile_lcdc_chan, therefore it had
to be extracted into a separate common header.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-09-14 17:23:21 +09:00
Guennadi Liakhovetski 44432407d9 fbdev: sh_mobile_lcdcfb: Support multiple video modes in platform data
This is a preparation for HDMI hotplug support. This patch just moves all
platform defined video modes for the sh_mobile_lcdcfb driver to separate
arrays and switches all users to use element 0 of that array, so, this patch
doesn't introduce any functional changes and as such should not cause any
regressions.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-09-14 17:22:38 +09:00
Kuninori Morimoto dec6aa49ab fbdev: sh_mobile_hdmi: modify flags name to more specific
This patch solve below report from Guennadi

1)

> +/* Audio source select */
> +#define HDMI_SRC_MASK		(0xF << 0)
> +#define HDMI_SRC_I2S		(0 << 0) /* default */
> +#define HDMI_SRC_SPDIF		(1 << 0)
> +#define HDMI_SRC_DSD		(2 << 0)
> +#define HDMI_SRC_HBR		(3 << 0)

I would be more specific with these macro names, i.e., include "AUDIO" or
"SND" or something similar in them, e.g., HDMI_AUDIO_SRC_I2S.

2)

> +	case HDMI_SRC_I2S:
> +		data = (0x0 << 3);
> +		break;
> +	case HDMI_SRC_SPDIF:
> +		data = (0x1 << 3);
> +		break;
> +	case HDMI_SRC_DSD:
> +		data = (0x2 << 3);
> +		break;
> +	case HDMI_SRC_HBR:
> +		data = (0x3 << 3);

In all above cases parenthesis are superfluous.

Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-09-10 16:07:41 +01:00
Kuninori Morimoto 6d86577124 fbdev: sh-mobile: Add HDMI sound type selection
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-09-01 11:17:49 +01:00
Justin P. Mattock c84e032e14 include/video/vga.h: update web address.
The below updates a broken web address to one(hopefully) thats
the new correct address.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-16 15:15:18 +02:00
Sam Ravnborg 60641aa1f3 include: replace unifdef-y with header-y
unifdef-y and header-y has same semantic.
So there is no need to have both.

Drop the unifdef-y variant and sort all lines again

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2010-08-14 22:26:51 +02:00
Guennadi Liakhovetski 6011bdeaa6 fbdev: sh-mobile: HDMI support for SH-Mobile SoCs
Some SH-Mobile SoCs have an HDMI controller and a PHY, attached to one of their
LCDC interfaces. This patch adds a preliminary static support for such
controllers, this means, that only the 720p mode is handled ATM. Support for
more modes and a dynamic switching between them will be added by a follow up
patch.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-08-04 16:12:15 +09:00
Guennadi Liakhovetski c243939817 sh: add a parameter to LCDC driver's .display_on() callback
HDMI support for the sh_mobile_lcdc framebuffer driver will require a 'struct
fb_info *' pointer for its .display_on() callback. While at it fix kfr2r09
framebuffer modular build.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-08-04 16:12:11 +09:00
Paul Mundt d5b732b17c Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 2010-05-31 13:14:26 +09:00
Grazvydas Ignotas 49c39b4953 fbdev: move FBIO_WAITFORVSYNC to linux/fb.h
FBIO_WAITFORVSYNC is currently implemented by matroxfb, atyfb, intelfb and
more.  All of them keep redefining the same FBIO_WAITFORVSYNC macro over
and over again, so move it to linux/fb.h and clean up those duplicate
defines.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Maik Broemme <mbroemme@plusserver.de>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-25 08:07:09 -07:00
Martin Ambrose 1f9c3e1f07 fbdev: da8xx/omap-l1xx: implement double buffering
This work includes the following:

- Implement handler for FBIO_WAITFORVSYNC ioctl.

- Allocate the data and palette buffers separately.  A consequence of
  this is that the palette and data loading is now done in different
  phases.  And that the LCD must be disabled temporarily after the palette
  is loaded but this will only happen once after init and each time the
  palette is changed.  I think this is OK.

- Allocate two (ping and pong) framebuffers from memory.

- Add pan_display handler which toggles the LCDC DMA registers between
  the ping and pong buffers.

Signed-off-by: Martin Ambrose <martin@ti.com>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-25 08:07:09 -07:00
Guennadi Liakhovetski 9fd04fe34a sh-mobile: add support for displays, connected over the MIPI bus
Some SH-mobile SoCs have a MIPI DSI controller, that can be used to connect
MIPI displays to LCDC. This patch adds a platform driver for SH-mobile MIPI DSI
unit. It uses existing hooks in the sh_mobile_lcdcfb.c driver for display
activation and deactivation.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-05-24 08:49:05 +09:00
Guennadi Liakhovetski 1430e006a3 sh: add a YUV422 output data format, that is also supported by LCDC
The LCDC block is allowed to use one of the two output data formats, when used
with MIPI DSI: RGB24 and YUV422. YUV422 is not currently handled by the LCDC
driver, but we have to add a define for it for MIPI.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-05-24 08:49:01 +09:00
Guennadi Liakhovetski ea95450eed fbdev: add a MIPI DSI header
This header adds defines for MIPI DSI and DCS commands and data formats. See
http://www.mipi.org/ for details.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-05-24 08:47:38 +09:00
Jaya Kumar b32bfc3843 broadsheetfb: support storing waveform
This patch adds waveform storing capability to broadsheetfb. It uses the
firmware class to retrieve the waveform, and the request to initiate the
waveform storing is done via a driver sysfs entry, loadstore_waveform.

Broadsheet is a framebuffer device.  It is slightly different from a
typical framebuffer controller that drives a normal TFT-LCD display.  Most
E-Ink display panels require a waveform in order to function.  That is, in
order to drive the state of a pixel to black, gray, or white, a specific
waveform is utilized.  Basically, that waveform represents the specific
E-field wiggling needed to get the pixel to its optimal state given
current temperature, and its previous state.  TN/IPS-LCDs use a similar
concept but the driving waveform is sufficiently simple that it is
internalized in the TFT source/gate driver.

These E-Ink waveforms are specific to a production batch.  That is, a
batch of display films are produced, then they get characterized and a
waveform is generated for that batch.  Broadsheet, typically, is attached
to its private SPI flash which is then flashed with this waveform.

Users won't be able to see the waveform and typically won't ever need to
know about it.  If however, the display panel attached to broadsheet is
changed out, then they will need to update their waveform.  That would
typically be done at a factory or repair facility rather than by a user.

[akpm@linux-foundation.org: fix printk warning]
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:34 -08:00
Jaya Kumar 2afb189817 broadsheetfb: add MMIO hooks
Allow boards with GP-MMIO controllers to provide hooks to broadsheetfb in
order to offload cmd/data writes and data reads instead of relying only on
host based GPIO wiggling.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:34 -08:00
Jaya Kumar c1c341a060 broadsheetfb: add multiple panel type support
Update broadsheetfb to add support for multiple panel types.  The 3.7" and
6" are known to work but the 9.7" is untested due to lack of hardware.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:32 -08:00
Phil Edworthy 40331b21f5 video: sh_mobile_lcdcfb: Add wait for vsync.
Added FBIO_WAITFORVSYNC ioctl for SH-Mobile devices.
Tested on MS7724 and MigoR boards against 2.6.33-rc7.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-02-16 13:30:27 +09:00
Linus Torvalds 9b2831704e Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
  sh: Fix test of unsigned in se7722_irq_demux()
  sh: mach-ecovec24: Add FSI sound support
  sh: mach-ecovec24: Add mt9t112 camera support
  sh: mach-ecovec24: Add tw9910 support
  sh: MSIOF/mmc_spi platform data for the Ecovec24 board
  sh: ms7724se: Add ak4642 support
  sh: Fix up FPU build for SH5
  sh: Remove old early serial console code V2
  sh: sh5 scif pdata (sh5-101/sh5-103)
  sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
  sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
  sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
  sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
  sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
  sh: sh2 scif pdata (sh7616)
  sh-sci: Extend sh-sci driver with early console V2
  sh: Stub in P3 ioremap support for nommu parts.
  sh: wire up vmallocinfo support in ioremap() implementations.
  sh: Make the unaligned trap handler always obey notification levels.
  sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
  ...
2009-12-16 10:29:52 -08:00
Chaithrika U S 3611380490 davinci: fb: update the driver in preparation for addition of power management features
Add a helper function to enable raster.  Also add one member in the
private data structure to track the current blank status, another function
pointer which takes in the platform specific callback function to control
panel power.

These updates will help in adding suspend/resume and frame buffer blank
operation features.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-16 07:20:04 -08:00
Paul Mundt b5c00a3a41 Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into sh/for-2.6.33 2009-12-10 15:40:31 +09:00
Linus Torvalds 4ef58d4e2a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
  tree-wide: fix misspelling of "definition" in comments
  reiserfs: fix misspelling of "journaled"
  doc: Fix a typo in slub.txt.
  inotify: remove superfluous return code check
  hdlc: spelling fix in find_pvc() comment
  doc: fix regulator docs cut-and-pasteism
  mtd: Fix comment in Kconfig
  doc: Fix IRQ chip docs
  tree-wide: fix assorted typos all over the place
  drivers/ata/libata-sff.c: comment spelling fixes
  fix typos/grammos in Documentation/edac.txt
  sysctl: add missing comments
  fs/debugfs/inode.c: fix comment typos
  sgivwfb: Make use of ARRAY_SIZE.
  sky2: fix sky2_link_down copy/paste comment error
  tree-wide: fix typos "couter" -> "counter"
  tree-wide: fix typos "offest" -> "offset"
  fix kerneldoc for set_irq_msi()
  spidev: fix double "of of" in comment
  comment typo fix: sybsystem -> subsystem
  ...
2009-12-09 19:43:33 -08:00
Magnus Damm ef61aae4dd sh: add a start_transfer() callback to the LCDC driver
This patch adds a ->start_transfer() callback to the
driver sh_mobile_lcdcfb.c. The callback is used to
program the LCDC panel in the case of one-shot mode.

Needed by the LCD controller used on the KFR2R09 board.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-12-09 12:40:44 +09:00
Thiago Farina 96c085db0a sgivwfb: Make use of ARRAY_SIZE.
Cleanup the usage of DBE_VT_SIZE since the kernel already defines the
same macro for the same propose.

Also clean up a surrounding whitespaces.

Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:52 +01:00
Jun Nie c41562b162 pxa168fb: remove useless vsync/hsync invert flag
fb_var_screeninfo.var has already encoded this information.

Signed-off-by: Jun Nie <njun@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-12-01 09:02:32 +08:00
Sudhakar Rajashekhara 2f93e8f482 davinci-fb-frame-buffer-driver-for-ti-da8xx-omap-l1xx-v4
Since the previous version, return values in ioctl() function have been
modified.

[akpm@linux-foundation.org: simplify lcd_disable_raster()]
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:51 -07:00
Sudhakar Rajashekhara 4ed824d9ae davinci: fb: Frame Buffer driver for TI DA8xx/OMAP-L1xx
Add LCD controller (LCDC) driver for TI's DA8xx/OMAP-L1xx architecture.
LCDC specifications can be found at http://www.ti.com/litv/pdf/sprufm0a.

LCDC on DA8xx consists of two independent controllers, the Raster
Controller and the LCD Interface Display Driver (LIDD) controller.  LIDD
further supports character and graphic displays.

This patch adds support for the graphic display (Sharp LQ035Q3DG01) found
on the DA830 based EVM.  The EVM details can be found at:
http://support.spectrumdigital.com/boards/dskda830/revc/.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
DESC
davinci-fb-frame-buffer-driver-for-ti-da8xx-omap-l1xx-fix
EDESC
From: Andrew Morton <akpm@linux-foundation.org>

fix kconfig indenting

Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:50 -07:00
Kristoffer Ericson 3ed167af96 fbdev: s1d13xxxfb: add accelerated bitblt functions
Add accelerated bitblt functions to s1d13xxx based video chipsets, more
specificly functions copyarea and fillrect.

It has only been tested and activated for 13506 chipsets but is expected
to work for the majority of s1d13xxx based chips.  This patch also cleans
up the driver with respect of whitespaces and other formatting issues.  We
update the current status comments.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16 19:48:00 -07:00
Lennert Buytenhek 638772c755 fb: add support of LCD display controller on pxa168/910 (base layer)
This driver is originally written by Lennert, modified by Green to be
feature complete,  and ported by Jun Nie and Kevin Liu for pxa168/910
processors.

The patch adds support for the on-chip LCD display controller, it
currently supports the base (graphics) layer only.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Green Wan <gwan@marvell.com>
Cc: Peter Liao <pliao@marvell.com>
Signed-off-by: Jun Nie <njun@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-06-13 00:09:09 +08:00
Joe Perches 1faca76fad include/video/cyblafb.h: remove it, it's unused
commit ddb53d48da ("fbdev: remove cyblafb
driver") removed drivers/video/cyblafb.c, but not its .h file

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Jani Monoses" <jani@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-13 15:04:30 -07:00
Krzysztof Helt feff3880d0 tdfxfb: move I2C functionality into the tdfxfb
The I2C functionality provided by the i2c-voodoo3 driver is moved into the
tdfxfb (frame buffer driver for Voodoo3 cards).  This way there is no
conflict between the i2c driver and the fb driver.

The tdfxfb does not make use from the DDC functionality yet but provides
all the functionality of the i2c-voodoo3 driver.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:08 -07:00
Kristoffer Ericson afbb9d8d52 fbdev: update s1d13xxxfb to differ between revisions and production ids
The s1d13xxx chip provides two values of identification value: the
Production id (e.g 13506/13505/13806..) and a revision number 0,1,2,3).
Together these can help us to differentiate between similiar setups.

This patch adds the proper way of grabbing both those values and save them
for future reference (in order to decide what functions a card supports,
e.g acceleration).

We also move away from the concept of all s1d13xxx = s1d13806 when we
really support alot more.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify s1d13xxxfb_probe()]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:32 -07:00
Roel Kluin 91ad120353 fbdev: newport: newport_*wait() return 0 on timeout
With a postfix decrement t reaches -1 on timeout which results in a
return of 0.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:31 -07:00
Krzysztof Helt 1b48cb563d cirrusfb: Laguna chipset 8bpp fix
Fix 8bpp mode by adding handling of the Laguna chipsets to various places
and stop trashing a HDR register which probably does not exist on the
Laguna.

Fix compilation warnings about uninitialized variables also.

Finally, all 8bpp, 16bpp and 32bpp modes work on the Laguna chipset.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:27 -07:00
Krzysztof Helt 213d4bdd8c cirrusfb: add Laguna additional overflow register
Add additional overflow register setting for Laguna chips.

Also, simplify some code in the cirrusfb_pan_display() and
cirrusfb_blank().

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:27 -07:00
Randy Dunlap d5cb78feee atyfb: fix header file trailing whitespace
Fix trailing whitespace because quilt complained about it.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:26 -07:00
Jaya Kumar 0d4ff4df34 [ARM] 5353/1: fbdev: add E-Ink Broadsheet controller support v3
This patch adds support for the E-Ink Broadsheet display controller.

Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-10 11:27:59 +00:00
Randy Dunlap fe86175bce atyfb: fix CONFIG_ namespace violations
Fix namespace violations by changing non-kconfig CONFIG_ names to CNFG_*.

Fixes breakage in staging/, which adds a real CONFIG_PANEL.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-05 12:56:48 -08:00
Jaswinder Singh Rajput de4d379552 headers_check fix: video/uvesafb.h
fix the following 'make headers_check' warning:

  usr/include/video/uvesafb.h:5: found __[us]{8,16,32,64} type without #include <linux/types.h>

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
2009-01-31 00:14:52 +05:30
Jaswinder Singh Rajput dab9c5e15e headers_check fix: video/sisfb.h
fix the following 'make headers_check' warnings:

  usr/include/video/sisfb.h:25: include of <linux/types.h> is preferred over <asm/types.h>
  usr/include/video/sisfb.h:78: found __[us]{8,16,32,64} type without #include <linux/types.h>

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
2009-01-31 00:14:28 +05:30
Magnus Damm 8564557a03 video: sh_mobile_lcdcfb deferred io support
This patch adds sh_mobile_lcdcfb deferred io support for SYS panels.

The LCDC hardware block managed by the sh_mobile_lcdcfb driver supports
RGB or SYS panel configurations. SYS panels come with an external display
controller that is resposible for refreshing the actual LCD panel. RGB
panels are controlled directly by the LCDC and they need to be refreshed
by the LCDC hardware.

In the case of SYS panels we can save some power by configuring the LCDC
hardware block in one-shot mode. In this one-shot mode panel refresh is
managed by software. This works well together with deferred io since it
allows us to stop clocks for most of the time and only enable clocks when
we actually want to trigger an update. When there is no fbdev activity
the clocks are kept stopped which allows us to deep sleep.

The refresh rate in deferred io mode is set using platform data. The same
platform data can also be used to disable deferred io mode.

As with other deferred io frame buffers user space code should use fsync()
on the frame buffer device to trigger an update.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:48 +09:00
Linus Torvalds 6c34bc2976 Revert "radeonfb: accelerate imageblit and other improvements"
This reverts commit b1ee26bab1, along with
the "fixes" for it that all just caused problems:

 - c4c6fa9891 "radeonfb: fix problem with
   color expansion & alignment"

 - f3179748a1 "radeonfb: Disable new color
   expand acceleration unless explicitely enabled"

because even when disabled, it breaks for people. See

	http://bugzilla.kernel.org/show_bug.cgi?id=12191

for the latest example.

Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-10 16:53:32 -08:00
Nicolas Ferre 722faccc7e atmel_lcdfb: change irq_base definition to allow error reporting
Changed because old the definition of unsigned long cannot be negative.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-12 17:17:16 -08:00
Magnus Damm f400f510df video: add sh_mobile_lcdc platform flags
Add platform data flags for detailed lcd display configuration.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 11:38:50 +09:00
Magnus Damm 7994b1c55e video: remove unused sh_mobile_lcdc platform data
Remove lddckr from the platform data, these days we calculate the
register value from clock source and clock dividers anyway.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 11:38:47 +09:00
Paul Mundt 4cb40f795a Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	Documentation/kernel-parameters.txt
	arch/sh/include/asm/elf.h
2008-10-20 11:17:52 +09:00
Kristoffer Ericson 0b178883b3 fbdev: allow more chip revisions in Epson s1d13... video driver
The Epson s1d13xxx hardware is common in many handhelds, but our driver is
currently locked to a single chip revision.  This patch adds an array of
known to work revisions (which can be extended).

[akpm@linux-foundation.org: cleanups]
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Acked-by: Thibaut Varène <varenet@parisc-linux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:45 -07:00
Benjamin Herrenschmidt b1ee26bab1 radeonfb: accelerate imageblit and other improvements
Implement support for HW color expansion of 1bpp images, along with some
improvements to the FIFO handling and other accel operations.

The offset fixup code is now unnecessary as the fbcon core will call our
set_par upon switch back from KD_GRAPHICS before anything else happens.  I
removed it as it would slow down accel operations.

The fifo wait has been improved to avoid hitting the HW register as often,
and the various accel ops are now performing better caching of register
values.

Overall, this improve accel performances.  The imageblit acceleration does
result in a small overall regression in performances on some machines (on
the order of 5% on some x86), probably becaus the SW path provides a
better bus utilisation, but I decided to ingnore that as the performances
is still very good, and on the other hand, some machines such as some
sparc64 get a 3 fold performance improvement.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:44 -07:00
Benjamin Herrenschmidt a6c0c37db6 radeonfb: misc cleanup of engine and dst cache handling
Fix a couple of incomplete tests of the chip families in the engine
init/reset code and proper initialization of the destination cache mode.
The result should better match what the latest X radeon driver does.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:44 -07:00
Krzysztof Helt 3a568051f3 neofb: remove open_lock mutex
Remove mutex from the fb_open/fb_release functions as these operations are
mutexed at fb layer.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:42 -07:00
Harvey Harrison d5c003b4d1 include: replace __FUNCTION__ with __func__
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:30 -07:00
Russell King 3f30a09a61 Merge branch 'pxa-all' into devel
Conflicts:

	arch/arm/mach-pxa/Kconfig
	arch/arm/mach-pxa/corgi.c
	arch/arm/mach-pxa/include/mach/hardware.h
	arch/arm/mach-pxa/spitz.c
2008-10-09 21:33:02 +01:00
Paul Mundt 225c9a8d1d video: sh_mobile_lcdcfb: Support HAVE_CLK=n configurations.
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.

At the same time, move the sh_mobile_lcdc.h header to include/video/.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-01 16:24:32 +09:00
Guillaume GARDET fbd03a1cbc [ARM] 5228/1: Add the RGB555 wiring for the atmel LCD
Add the RGB555 wiring for the atmel LCD.

Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-18 23:11:56 +01:00
Jaya Kumar e935508515 [ARM] 5209/1: metronomefb: changes to use platform framebuffer
These changes are used in order to support the use of the framebuffer
provided by the platform device driver rather than to directly allocate one.
Other changes are cleanup to error handling and order of release.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-26 17:01:12 +01:00
Haavard Skinnemoen ea757acad5 atmel_lcdfb: add board parameter specify framebuffer memory size
Specify how much physically continuous, DMA capable memory will be
allocated at driver initialization time.  This allow to create framebuffer
device with larger virtual resolution.  Combine with y-panning this can be
used to implement double buffering acceleration method.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-12 16:07:29 -07:00
David Miller 969830b2fe radeonfb: fix accel engine hangs
Some chips appear to have the 2D engine hang during screen redraw,
typically in a sequence of copyarea operations. This appear to be
solved by adding a flush of the engine destination pixel cache
and waiting for the engine to be idle before issuing the accel
operation. The performance impact seems to be fairly small.

Here is a trace on an RV370 (PCI device ID 0x5b64), it records the
RBBM_STATUS register, then the source x/y, destination x/y, and
width/height used for the copy:

----------------------------------------
radeonfb_prim_copyarea: STATUS[00000140] src[210:70] dst[210:60] wh[a0:10]
radeonfb_prim_copyarea: STATUS[00000140] src[2b8:70] dst[2b8:60] wh[88:10]
radeonfb_prim_copyarea: STATUS[00000140] src[348:70] dst[348:60] wh[40:10]
radeonfb_prim_copyarea: STATUS[80020140] src[390:70] dst[390:60] wh[88:10]
radeonfb_prim_copyarea: STATUS[8002613f] src[40:80] dst[40:70] wh[28:10]
radeonfb_prim_copyarea: STATUS[80026139] src[a8:80] dst[a8:70] wh[38:10]
radeonfb_prim_copyarea: STATUS[80026133] src[e8:80] dst[e8:70] wh[80:10]
radeonfb_prim_copyarea: STATUS[8002612d] src[170:80] dst[170:70] wh[30:10]
radeonfb_prim_copyarea: STATUS[80026127] src[1a8:80] dst[1a8:70] wh[8:10]
radeonfb_prim_copyarea: STATUS[80026121] src[1b8:80] dst[1b8:70] wh[88:10]
radeonfb_prim_copyarea: STATUS[8002611b] src[248:80] dst[248:70] wh[68:10]
----------------------------------------

When things are going fine the copies complete before the next ROP is
even issued, but all of a sudden the 2D unit becomes active (bit 17 in
RBBM_STATUS) and the FIFO retry (bit 13) and FIFO pipeline busy (bit
14) are set as well.  The FIFO begins to backup until it becomes full.

What happens next is the radeon_fifo_wait() times out, and we access
the chip illegally leading to a bus error which usually wedges the
box.  None of this makes it to the console screen, of course :-)
radeon_fifo_wait() should be modified to reset the accelerator when
this timeout happens instead of programming the chip anyways.

----------------------------------------
radeonfb: FIFO Timeout !
ERROR(0): Cheetah error trap taken afsr[0010080005000000] afar[000007f900800e40] TL1(0)
ERROR(0): TPC[595114] TNPC[595118] O7[459788] TSTATE[11009601]
ERROR(0): TPC<radeonfb_copyarea+0xfc/0x248>
ERROR(0): M_SYND(0),  E_SYND(0), Privileged
ERROR(0): Highest priority error (0000080000000000) "Bus error response from system bus"
ERROR(0): D-cache idx[0] tag[0000000000000000] utag[0000000000000000] stag[0000000000000000]
ERROR(0): D-cache data0[0000000000000000] data1[0000000000000000] data2[0000000000000000] data3[0000000000000000]
ERROR(0): I-cache idx[0] tag[0000000000000000] utag[0000000000000000] stag[0000000000000000] u[0000000000000000] l[00\

ERROR(0): I-cache INSN0[0000000000000000] INSN1[0000000000000000] INSN2[0000000000000000] INSN3[0000000000000000]
ERROR(0): I-cache INSN4[0000000000000000] INSN5[0000000000000000] INSN6[0000000000000000] INSN7[0000000000000000]
ERROR(0): E-cache idx[800e40] tag[000000000e049f4c]
ERROR(0): E-cache data0[fffff8127d300180] data1[00000000004b5384] data2[0000000000000000] data3[0000000000000000]
Ker:xnel panic - not syncing: Irrecoverable deferred error trap.
----------------------------------------

Another quirk is that these copyarea calls will not happen until the
first drivers/char/vt.c:redraw_screen() occurs.  This will only happen
if you 1) VC switch or 2) run "consolechars" or 3) unblank the screen.

This seems to happen because until a redraw_screen() the screen scrolling
method used by fbcon is not finalized yet.  I've seen this with other fb
drivers too.

So if all you do is boot straight into X you will never see this bug on
the relevant chips.

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-12 16:07:28 -07:00
David Miller efc4918143 radeon: misc corrections
I have a new PCI-E radeon RV380 series card (PCI device ID 5b64) that
hangs in my sparc64 boxes when the init scripts set the font.  The problem
goes away if I disable acceleration.

I haven't figured out that bug yet, but along the way I found some
corrections to make based upon some auditing.

1) The RB2D_DC_FLUSH_ALL value used by the kernel fb driver
   and the XORG video driver differ.  I've made the kernel
   match what XORG is using.

2) In radeonfb_engine_reset() we have top-level code structure
   that roughly looks like:

	if (family is 300, 350, or V350)
		do this;
	else
		do that;
	...
	if (family is NOT 300, OR
	    family is NOT 350, OR
	    family is NOT V350)
		do another thing;

   this last conditional makes no sense, is always true,
   and obviously was likely meant to be "family is NOT
   300, 350, or V350".  So I've made the code match the
   intent.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-05 14:33:49 -07:00
Adrian Bunk 44ccac13c7 include/video/atmel_lcdc.h must #include <linux/workqueue.h>
This patch fixes the following compile error caused by commit
d22579b837 ("atmel_lcdfb: FIFO underflow
management"):

  In file included from arch/avr32/boards/atstk1000/atstk1004.c:21:
  include/video/atmel_lcdc.h:40: error: field 'task' has incomplete type

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-26 12:00:01 -07:00
Krzysztof Helt c6b044d6ba neofb: drop the xtimings structure
Remove the xtimings structure which only stored some values to be used
later (mostly once).  Calculate and use these values in places they are
needed.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:41 -07:00
Ben Dooks c25826a7cf lcd: add platform_lcd driver
Add a platform_lcd driver to allow boards with simple lcd power controls
to register themselves easily.

[akpm@linux-foundation.org: build fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:40 -07:00
Ben Dooks cccb6d3c14 fb: add support for the ILI9320 video display controller
Provide support for the ILI9320 display controller chip which is found in
many LCD displays.  Included with this is support for an example LCD using
this chip, the VGG2432A4.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:40 -07:00
Nicolas Ferre d22579b837 atmel_lcdfb: FIFO underflow management
Manage atmel_lcdfb FIFO underflow

Resetting the LCD and DMA allows to fix screen shifting after a FIFO
underflow.  It follows reset sequence from errata "LCD Screen Shifting
After a Reset".

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:37 -07:00
Krzysztof Helt 0292be4a38 tridentfb: add imageblit acceleration for Blade3D family
Add imageblit acceleration for the Blade3D family of cores.  The code is
based on code from the cyblafb driver.

It is a step toward assimilating back the cyblafb driver into the
tridentfb driver.  The cyblafb driver handles a subfamily of the Trident
Blade3d cores.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:36 -07:00
Krzysztof Helt 5cf138457a tridentfb: source code improvements
This patch contains general source code improvments:
 - more simple functions are inline
 - removes some meaningless output and the VERSION
   string as it is no use
 - eng_par is moved into the tridentfb_par
 - removed small section of code for CyberBladeXPAi1
   which is maybe right for only one resolution
   and refresh rate and is probably redundant now
 - other minor improvements

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:36 -07:00
Krzysztof Helt 49b1f4b44b tridentfb: acceleration code improvements
This patch brings various acceleration improvements:
- set  copyarea/fillrect for non-accelerated framebuffer (fix)
- remove 15 bpp depth handling to simplify code as it hardly
  works (15 bpp handling was obviously missing in some switches)
- add fb_sync call and move waiting before accelerated function
  to make acceleration more asynchronous to cpu (few % of speed
  improvement)
- add cpu_relax() call in waiting loops
- make longer register names and name more registers
- move registers' definition to header
- general code improvements (shortening, simplifying)

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:36 -07:00
Krzysztof Helt a0d922562d tridentfb: add TGUI 9440 support
Add support for TGUI 9440 chip.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:35 -07:00
Krzysztof Helt 0e73a47f09 tridentfb: improved register values on TGUI 9680
Improved values for some registers after Xorg Trident driver.  The main
problem was that values set by BIOS have been ignored.

This patch completely remove random pixels ("snow") on the TGUI 9680 and
9440 (not supported yet by the driver).  It does not help with the "snow"
on 3DImage and Blade3D cards.

There is also small improvement in timing calculations (hblank start and
vblank start)

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:35 -07:00
Krzysztof Helt 10172ed6dc tridentfb: make use of functions and constants from the vga.h
Make use of functions and constants from the vga.h header to compact the code
and make it more readable.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:35 -07:00
Krzysztof Helt e0759a5fbb tridentfb: convert is_blade and is_xp macros into functions
This patch converts the is_blade() and is_xp() macros into local functions.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:35 -07:00
Krzysztof Helt 6eed8e1ec8 tridentfb: move global flat panel variable into structure
This patch moves flat panel indicator into tridentfb_par structure and removes
related global variables and macros.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:35 -07:00
Jaya Kumar 0e27aa3dab fbdev: platforming hecubafb and n411
This patch splits hecubafb into the platform independent hecubafb and the
platform dependent n411.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:41 -07:00
Jaya Kumar 03c33a4f00 fbdev: platforming metronomefb and am200epd
This patch splits metronomefb into the platform independent metronomefb and
the platform dependent am200epd.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:41 -07:00
Nicolas Ferre fd0858017e atmel_lcdfb: wiring BGR to RGB color mode
Adds different wiring mode for the LCD screen.

The legacy atmel LCDC IP uses a non standard color mode, "BGR-555.1" instead
"RGB-565".  The major part of graphic stacks for embedded systems uses only
"RGB-565".  It is possible to swap LCD IOs instead of doing this bit swapping
by software (See application note AT91SAM9 LCD Controller
http://www.atmel.com/dyn/resources/prod_documents/doc6300.pdf)

This wire swapping is done on the at91sam9rl-ek board (board code
using this patch will come later).

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
David Brownell cf19a37e06 atmel_lcdfb: suspend/resume support
Teach atmel_lcdfb driver how to suspend/resume.

Note that the backlight control should probably do more of the same stuff:
turning off display power (more than just the backlight) and stopping the
clocks (and dma to drive the no-longer-seen display).  No point in wasting
power to generate images that can't be observed, after all...

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:38 -07:00
David Brownell a9a84c37d1 atmel_lcdfb: backlight control
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller.  It's controlled by "contrast" registers though.

This patch lets boards declare that they have that kind of backlight
control.  The driver can then export this control, letting screenblank and
other operations actually take effect ...  reducing the typically
substantial power drain from the backlight.

Note that it's not fully cooked
  - doesn't force backlight off during system suspend
  - the "power" and "blank" events may not be done right
This should be easily added in the future.

[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:16 -08:00
Haavard Skinnemoen 162b3a0849 atmel_lcdfb: validate display timings
Setting a display timing parameter too high or too low may cause it to
wrap around and thus become completely wrong. Validate the timings in
atmel_lcdfb_check_var() and saturate to the highest or lowest possible
value if necessary.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:15 -08:00
Rusty Russell ee8e7cfe9d Make asm-x86/bootparam.h includable from userspace.
To actually write a bootloader (or, say, the lguest launcher)
currently requires duplication of these structures.  Making them
includable from userspace is much nicer.

We merge the common userspace-required definitions of e820_32/64.h
into e820.h for export.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23 15:49:47 +10:00
Jiri Slaby 93043ece03 define global BIT macro
define global BIT macro

move all local BIT defines to the new globally define macro.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-19 11:53:42 -07:00
Krzysztof Helt 2a36f9c497 pm2fb: hardware cursor support for the Permedia2
This patch adds hardware cursor support for the Permedia 2 chip.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:18 -07:00
Krzysztof Helt e84d436b3c pm3fb: header file cleanup
This patch fixes white spaces, redudant definitions and formating in the pm3fb
header file.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:18 -07:00
Krzysztof Helt 8f5d050af1 pm2fb: Permedia 2V hardware cursor support
This patch adds hardware cursor support for Permedia 2V chips.
The hardware cursor is disabled by default. It does not blink - the
same issue is mentioned in the x11 driver.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:16 -07:00
Krzysztof Helt 0960bd3db1 tdfxfb: mtrr support
This patch adds mtrr support to the tdfxfb driver.  It also kills one
redundant include and initialization value.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:15 -07:00
Krzysztof Helt 90b0f08536 tdfxfb: hardware cursor
This patch adds hardware cursor support to the tdfxfb driver.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:15 -07:00
Krzysztof Helt 4f05b53b28 tdfxfb: code improvements
This patch improves source code mainly by killing redundant variable loads,
reducing number of variables, simplifying conditional branches, etc.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:15 -07:00
Krzysztof Helt 8af1d50f7f tdfxfb: coding style improvement
This patch contains coding style improvements to the tdfxfb driver (white
spaces, indentations, long lines).

It also moves fb_ops structure to the end of file, so forward declarations of
ops functions are redundant.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:15 -07:00
Raphael Assenat ba282daa91 mbxfb: Improvements and new features
This contains the following changes:

* Overlay surface alpha is configured separately from the overlay. This
prevents display glitches (configure and fill the overlay first, set
alpha to a visible value next)

* Added an ioctl for configuring transparency of the Overlay and graphics
planes. Blend mode, colorkey mode and global alpha mode are supported.

* Added an ioctl for setting the plane order. The overlay plance can be placed
over or
under the graphics plane.

* Added an ioctl for setting and reading chip registers, with mask.

* Updated copyright for 2007

[adaplas]
* Coding style changes

Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:14 -07:00
Krzysztof Helt 138a451cce pm2fb: Permedia 2V initialization fixes
This patch:
- initializes correctly the Permedia2V chip if it is not initialized by BIOS
- puts back clock frequency for the ELSA WINNER board to 100kHz
- fixes returned error values from setcolreg() function
- uses more general classes for PCI ids

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:14 -07:00
Krzysztof Helt 91b3a6f4cd pm2fb: accelerated imageblit
This patch adds accelerated imageblit function.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:14 -07:00
Krzysztof Helt f259ebb67b pm3fb: header file reduction
This patch removes constants named AAA_DISABLE with value 0. They are redudant
and misleading ( a |= AAA_DISABLE does nothing and usually should be
a &= ~AAA_ENABLE).

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:14 -07:00
Krzysztof Helt e7f76df964 pm3fb: copyarea and partial imageblit suppor
This patch adds accelerated copyarea and partially accelerated imageblit
functions. There is also fixed one register address in the pm3fb.h file.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:14 -07:00
Michal Januszewski 8bdb3a2d7d uvesafb: the driver core
uvesafb is an enhanced version of vesafb.  It uses a userspace helper (v86d)
to execute calls to the x86 Video BIOS functions.  The driver is not limited
to any specific arch and whether it works on a given arch or not depends on
that arch being supported by the userspace daemon.  It has been tested on
x86_32 and x86_64.

A single BIOS call is represented by an instance of the uvesafb_ktask
structure.  This structure contains a buffer, a completion struct and a
uvesafb_task substructure, containing the values of the x86 registers, a flags
field and a field indicating the length of the buffer.  Whenever a BIOS call
is made in the driver, uvesafb_exec() builds a message using the uvesafb_task
substructure and the contents of the buffer.  This message is then assigned a
random ack number and sent to the userspace daemon using the connector
interface.

The message's sequence number is used as an index for the uvfb_tasks array,
which provides a mapping from the messages coming from userspace to the
in-kernel uvesafb_ktask structs.

The userspace daemon performs the requested operation and sends a reply in the
form of a uvesafb_task struct and, optionally, a buffer.  The seq and ack
numbers in the reply should be exactly the same as those in the request.

Each message from userspace is processed by uvesafb_cn_callback() and after
passing a few sanity checks leads to the completion of a BIOS call request.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:13 -07:00
Yoichi Yuasa 541510fc28 remove tx3912fb
Remove tx3912fb.  Nino has already removed.  It is no longer needed.

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31 15:39:41 -07:00
Antonino A. Daplas eb3daa83c2 tgafb: actually allocate memory for the pseudo_palette
No memory allocation was done for the pseudo_palette.  Allocate one for it.

Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Acked-by: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 10:23:12 -07:00
Nicolas Ferre 1434058614 atmel_lcdfb: AT91/AT32 LCD Controller framebuffer driver
Adds a framebuffer driver to ATMEL AT91SAM9x and AT32 aka AVR32 platforms.
Those chips share quite the same IP and this code is suitable for both
architectures.

Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-11 08:29:37 -07:00
Krzysztof Helt f23a06f076 pm3fb: Preliminary 2.4 to 2.6 port
This is a basic port from 2.4 kernel to 2.6.  Acceleration is lost and big
endian support probably too.  The driver works in 8, 16 and 32 bit mode.

[adaplas]
- change VESA_* to FB_BLANK_* constants
- removed unused function clear_memory
- fix uninitialized variable compiler warning
- some whitespace cleaning

[akpm@linux-foundation.org: Nuke pestiferous CVS string]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-11 08:29:37 -07:00
Ville Syrjala 159dde9369 atyfb: halve XCLK with Mobility and 32bit memory
Laptops with Rage Mobility and 32bit memory interface seem to require halved
XCLK to operate correctly.

Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08 11:15:32 -07:00
Krzysztof Helt e5d809d774 pm2fb: Permedia 2V memory clock setting
Permedia 2V uses its own registers to set a memory clock. The
patch adds these registers and uses them in the set_memclock()
function.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08 11:15:32 -07:00
Maciej W. Rozycki 86c6f7d08b tgafb: TURBOchannel support
This is support for the TC variations of the TGA boards (properly known as
SFB+ or Smart Frame Buffer Plus boards).  The 8-plane SFB+ board uses the
Bt459 RAMDAC (unlike its PCI TGA counterpart, which uses the Bt485), so
bits have been added to support this chip as well.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: James Simmons <jsimmons@infradead.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08 11:15:27 -07:00
Jiri Slaby c4f28e54d6 [PATCH] Video: fb, add true ref_count atomicity
Some of fb drivers uses atomic_t in bad manner, since there are still some
race-prone gaps.  Use mutexes to protect open/close code sections with
ref_count testing and finally use simple uint.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Denis Oliver Kropp <dok@directfb.org>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-12 09:48:42 -08:00
Adrian Bunk 52e7c922f3 [PATCH] remove the broken FB_S3TRIO driver
The FB_S3TRIO driver:
- has been marked as BROKEN for more than two years and
- is still marked as BROKEN.

Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.

But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: James Simmons <jsimmons@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-12 09:48:42 -08:00
Helge Deller 0743b86800 [PATCH] sstfb: add sysfs interface
Modify the sstfb (Voodoo1/2) driver:

- fix a memleak when removing the sstfb module

- fix sstfb to use the fbdev default videomode database

- add module option "mode_option" to set initial screen mode

- add sysfs-interface to turn VGA-passthrough on/off via
  /sys/class/graphics/fbX/vgapass

- remove old debug functions from ioctl interface

Signed-off-by: Helge Deller <deller@gmx.de>
Acked-By: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:05:55 -08:00
Mariusz Kozlowski f4b85dc0a1 [PATCH] video: pm3fb macros fix
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Raphael Assenat ea465250d4 [PATCH] mbxfb: Add YUV video overlay support
This patch adds a way to create and use the video plane (YUV overlay) and
scaling video scaling features of the chip.

The overlay is configured, resized and modified using a device specific
ioctl.

Also included in this patch:
  - If no platform data was passed, print an error and exit instead of crashing.
  - Added a write_reg(_dly) macro. This improves readability when
    manipulating chip registers. (no more udelay() after each write).
  - Comments about some issues.

Signed-off-by: Raphael Assenat <raph@8d.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:06 -08:00
Uwe Zeisberger f30c226954 fix file specification in comments
Many files include the filename at the beginning, serveral used a wrong one.

Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 23:01:26 +02:00
Alan Cox b98fc9a34b [PATCH] sstfb: cleanups
- Remove 24/32bit unused support (the chips don't do 24/32bit anyway)
- Clean up printk obfuscation
- Clean up lispitus in the if(())()) stuff
- Minor tidying

No functionality changes, may have a crack at hardware scrolling based
on my X driver once the cleanups are in.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:13 -07:00
David Woodhouse fadcfa33b6 [HEADERS] One line per header in Kbuild files to reduce conflicts
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-09-19 12:43:58 +01:00
Mike Rapoport 22caf04297 [PATCH] mbxfb: Add framebuffer driver for the Intel 2700G
Add frame buffer driver for the 2700G LCD controller present on CompuLab
CM-X270 computer module.

[adaplas]
- Add more informative help text to Kconfig
- Make DEBUG a Kconfig option as FB_MBX_DEBUG
- Remove #include mbxdebug.c, this is frowned upon
- Remove redundant casts
- Arrange #include's alphabetically
- Trivial whitespace

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-14 21:53:55 -07:00
David Woodhouse 8555255f0b Add generic Kbuild files for 'make headers_install'
This adds the Kbuild files listing the files which are to be installed by
the 'headers_install' make target, in generic directories.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-06-18 12:14:01 +01:00
David Woodhouse 62c4f0a2d5 Don't include linux/config.h from anywhere else in include/
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-04-26 12:56:16 +01:00
Rusty Russell 8d3b33f67f [PATCH] Remove MODULE_PARM
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused.  It's time to replace the last users, which are generally in the
most unloved drivers anyway.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-25 08:22:52 -08:00
Christian Trefzer 9f672004ab [PATCH] neofb: avoid resetting display config on unblank (v2)
There were two mistakes in the register-read-on-(un)blank approach.

- First, without proper register (un)locking the value read back will always
  be zero, and this is what I missed entirely until just now.  Due to this,
  the logic could not be verified at all and I tried some bogus checks which
  are completely stupid.

- Second, the LCD status bit will always be set to zero when the backlight
  has been turned off.  Reading the value back during unblank will disable the
  LCD unconditionally, regardless of the state it is supposed to be in, since
  we set it to zero beforehand.

So this is what we do now:

- create a new variable in struct neofb_par, and use that to determine
  whether to read back registers (initialized to true)

- before actually blanking the screen, read back the register to sense any
  possible change made through Fn key combo

- use proper neoUnlock() / neoLock() to actually read something

- every call to neofb_blank() determines if we read back next time: blanking
  disables readback, unblanking (FB_BLANK_UNBLANK) enables it

This should give us a nice and clean state machine.  Has been thoroughly
tested on a Dell Latitude CPiA / NM220 Chip docked to a C/Dock2 with attached
CRT in all possible combinations of LCD/CRT on/off.  I changed the config via
Fn key, let the console blank, unblanked by keypress - works flawlessly.

Signed-off-by: Christian Trefzer <ctrefzer@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-15 15:32:21 -08:00
Adrian Bunk 3f08ff4a4d [PATCH] include/video/newport.h: "extern inline" -> "static inline"
"extern inline" doesn't make much sense.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-10 08:01:50 -08:00
Antonino A. Daplas 7227576f4b [PATCH] fbdev: sstfb: Driver cleanups
- remove unneeded casts
- make setcolreg return success if regno > 15, but don't do anything
- use framebuffer_alloc/framebuffer_release to allocate/free memory

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-10 08:01:46 -08:00
Antonino A. Daplas a807f618b6 [PATCH] fbdev: tdfxfb: Driver cleanups
- remove unneeded casts
- move memory for pseudo_palette inside struct tdfxfb_par
- whitespace changes

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-10 08:01:46 -08:00
Antonino A. Daplas 9f19bc56c3 [PATCH] fbdev: neofb: Driver cleanups
- remove unneeded casts
- move memory for pseudo_palette inside struct neofb_par

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-10 08:01:45 -08:00
Antonino A. Daplas a26968df01 [PATCH] fbdev: kyrofb: Driver cleanups
- remove unneeded casts

- use framebuffer_alloc/framebuffer_release to allocate/free memory

- the pseudo_palette is always u32 regardless of bpp if using generic
  drawing functions

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-10 08:01:45 -08:00
Knut Petersen 44637a12f8 [PATCH] Update cyblafb driver
This is a major update to the cyblafb framebuffer driver. Most
of the stuff has been tested in the mm tree.

Main advantages:
============
  - vxres > xres support
  - ywrap and xpan support
  - much faster for almost all modes (e.g. 1280x1024-16bpp
     draws more than 41 full screens of text instead of about 25
     full screens of text per second on authors Epia 5000)
  - module init/exit code fixed
  - bugs triggered by console rotation fixed
  - lots of minor improvements
  - startup modes suitable for high performance scrolling
     in all directions

This diff  also contains a lot of white space fixes.

No side effects are possible, only one single graphics core is affected.

Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-09 10:00:36 -08:00
Tobias Klauser 82006d0841 [PATCH] drivers/video: Replace custom macro with isdigit()
Replace the custom CHAR_IS_NUM() macro with isdigit() from <linux/ctype.h>

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-13 08:22:33 -07:00
Richard Purdie 513b6e1afa [PATCH] SharpSL: Abstract c7x0 specifics from Corgi Touchscreen driver
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
Touchscreen driver.  Use the new functions in corgi_lcd.c via sharpsl.h for
hsync handling and pass the IRQ as a platform device resource.  Move a
function prototype into the w100fb header file where it belongs.

This enables the driver to be used by the Zaurus cxx00 series.

Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-13 08:22:31 -07:00
Knut Petersen 9fa68eae9f [PATCH] framebuffer: new driver for cyberblade/i1 graphics core
This is a framebuffer driver for the Cyberblade/i1 graphics core.

Currently tridenfb claims to support the cyberblade/i1 graphics core.  This
is of very limited truth.  Even vesafb is faster and provides more working
modes and a much better quality of the video signal.  There is a great
number of bugs in tridentfb ...  but most often it is impossible to decide
if these bugs are real bugs or if fixing them for the cyberblade/i1 core
would break support for one of the other supported chips.

Tridentfb seems to be unmaintained,and documentation for most of the
supported chips is not available.  So "fixing" cyberblade/i1 support inside
of tridentfb was not an option, it would have caused numerous
if(CYBERBLADEi1) else ...  cases and would have rendered the code to be
almost unmaintainable.

A first version of this driver was published on 2005-07-31.  A fix for a
bug reported by Jochen Hein was integrated as well as some changes
requested by Antonino A.  Daplas.

A message has been added to tridentfb to inform current users of tridentfb
to switch to cyblafb if the cyberblade/i1 graphics core is detected.

This patch is one logical change, but because of the included documentation
it is bigger than 70kb.  Therefore it is not sent to lkml and
linux-fbdev-devel,

Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 13:58:02 -07:00
Thomas Winischhofer 544393fe58 [PATCH] sisfb update
This lifts sisfb from version 1.7.17 to version 1.8.9. Changes include:

- Added support for XGI V3XT, V5, V8, Z7 chipsets, including POSTing of
  all of these chipsets.

- Added support for latest SiS chipsets (761).

- Added support for SiS76x memory "hybrid" mode.

- Added support for new LCD resolutions (eg 1280x854, 856x480).

- Fixed support for 320x240 STN panels (for embedded devices).

- Fixed many HDTV modes (525p, 750p, 1080i).

- Fixed PCI config register reading/writing to use proper kernel
  functions for this purpose.

- Fixed PCI ROM handling to use the kernel's proper functions.

- Removed lots of "typedef"s.

- Removed lots of code which was for X.org/XFree86 only.

- Fixed coding style in many places.

- Removed lots of 2.4 cruft.

- Reduced stack size by unifying two previously separate structs into
  one.

- Added new hooks for memory allocation (for DRM).  Now the driver can
  truly handle multiple cards, including memory management.

- Fixed numerous minor bugs.

Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 13:58:01 -07:00
Richard Purdie aac51f09d9 [PATCH] w100fb: Rewrite for platform independence
The code w100fb was based on was horribly Sharp SL-C7x0 specific and there
was little else that could be done as I had no access to anything else with
a w100 in it.  There is no real documentation about this chipset available.

Ian Molton has access to other platforms with the w100 (Toshiba e-series)
and so between us, we've improved w100fb and made it platform independent.
Ian Molton also added support for the very similar w3220 and w3200
chipsets.

There are a lot of changes here and it nearly amounts to a rewrite of the
driver but it has been extensively tested and is being used in preference
to the original driver in the Zaurus community.  I'd therefore like to
update the mainline code to reflect this.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 16:57:53 -07:00
Ralf Baechle 7901c79982 [PATCH] DEC PMAGB B framebuffer update
Revive HX frame buffer support for 2.6.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-05 00:06:03 -07:00
Ralf Baechle af690a948c [PATCH] DEC PMAG BA frame buffer update
Rewrite PMAG BA frame buffer driver for 2.6.

Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-05 00:06:03 -07:00
Richard Drummond 333f981720 [PATCH] Clean-up and bug fix for tdfxfb framebuffer size detection
Attached is a patch against 2.6.11.7 which tidies up the tdfxfb framebuffer
size detection code a little and fixes the broken support for Voodoo4/5
cards.  (I haven't tested this on a Voodoo5, however, because I don't have
the hardware).

Signed-off-by: Richard Drummond <evilrich@rcdrummond.net>
Cc: <linux-fbdev-devel@lists.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-05-01 08:59:25 -07:00
Adrian Bunk 5f76be80d9 [PATCH] fbdev: edid.h cleanups
This patch removes some completely unused code.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-05-01 08:59:23 -07:00
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00