PM will take care of the status of child device, so no need
check each port anymore.
Suggested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618555706-6810-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows PMIC charger loops which are slow(i.e. cannot meet the
15ms deadline) to still comply to pSnkStby i.e Maximum power
that can be consumed by sink while in Sink Standby state as defined
in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification
Revision 3.0, Version 1.2.
This patch introduces slow-charger-loop which when set makes
the port request PD_P_SNK_STDBY_MW(2.5W i.e 500mA@5V) upon entering
SNK_DISCOVERY (instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414142656.63749-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2 driver has everything we need to run
in ACPI mode except for the ACPI module device table
boilerplate. With that added and identified as "BCM2848",
an id in use by other OSs for this device, the dw2
controller on the BCM2711 will work.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20210413215834.3126447-2-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.
Both actions need to be done conditionally.
Fixes: 6069e3e927 ("USB: cdc-acm: untangle a circular dependency between callback and softint")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable status is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed and move the
declaration of status to the scope where it is used.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420110622.377339-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable result is being assigned with a value that is
never read, the assignment is redundant and can be removed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420113818.378478-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The START_TRANSFER command needs to be executed while in ON/U0 link
state (with an exception during register initialization). Don't use
dwc->link_state to check this since the driver only tracks the link
state when the link state change interrupt is enabled. Check the link
state from DSTS register instead.
Note that often the host already brings the device out of low power
before it sends/requests the next transfer. So, the user won't see any
issue when the device starts transfer then. This issue is more
noticeable in cases when the device delays starting transfer, which can
happen during delayed control status after the host put the device in
low power.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/bcefaa9ecbc3e1936858c0baa14de6612960e909.1618884221.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon driver unbind usb_free_all_descriptors() function frees all
speed descriptor pointers without setting them to NULL. In case
gadget speed changes (i.e from super speed plus to super speed)
after driver unbind only upto super speed descriptor pointers get
populated. Super speed plus desc still holds the stale (already
freed) pointer. Fix this issue by setting all descriptor pointers
to NULL after freeing them in usb_free_all_descriptors().
Fixes: f5c61225cf ("usb: gadget: Update function for SuperSpeedPlus")
cc: stable@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
Fixes: e3a0720224 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A dedicated wakeup irq will be used to handle runtime suspend/resume,
we use dev_pm_set_dedicated_wake_irq API to take care of requesting
and attaching wakeup irq, then the suspend/resume framework will help
to enable/disable wakeup irq.
The runtime PM is default off since some platforms may not support it.
users can enable it via power/control (set "auto") in sysfs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618031406-15347-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an interrupt which is EINT usually to support runtime PM,
meanwhile add "interrupt-names" property, for backward
compatibility, it's optional and used when wakeup interrupt
exists
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618031406-15347-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a PD charger advertising Rp-3.0 is connected to a sink port, the
sink port current limit would 3A, during SNK_DISCOVERY, till power
negotiation starts. Once the negotiation starts the power limit needs
to drop down to pSnkStby(500mA @ 5V) and to negotiated current limit
once the explicit contract is in place. Not all charging loops can ramp
up to 3A and drop down to 500mA within tSnkStdby which is 15ms. The port
partner might hard reset if tSnkStdby is not met.
To solve this problem, this patch introduces slow-charger-loop which
when set makes the port request PD_P_SNK_STDBY_MW upon entering
SNK_DISCOVERY(instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a shutdown callback to USB DWC core driver to ensure that
it is properly shutdown in reboot/shutdown path. This is required
where SMMU address translation is enabled like on SC7180
SoC and few others. If the hardware is still accessing memory after
SMMU translation is disabled as part of SMMU shutdown callback in
system reboot or shutdown path, then IOVAs(I/O virtual address)
which it was using will go on the bus as the physical addresses which
might result in unknown crashes (NoC/interconnect errors).
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Link: https://lore.kernel.org/r/1618380209-20114-1-git-send-email-sanm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the controller handles single stream only. So, Ignore Packet
Pending bit for stream selection and don't search for another stream if
the host sends Data Packet with PP=0 (for OUT direction) or ACK with
NumP=0 and PP=0 (for IN direction). This slightly improves the stream
performance.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/097ba9e104c143f7ba0195ebff29390ec3043692.1618282705.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM
enabled:
[ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71
So disable LPM to resolve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1922651
Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains about a potential missing error code:
drivers/usb/typec/port-mapper.c:168 typec_link_port()
warn: missing error code 'ret'
This is a false positive and returning zero is intentional. Let's
re-arrange the code to silence the warning and make the intent more
clear.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YHadaACH8Mq/10F7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc2 core is in clock gating mode loading driver
again causes driver fail. Because in that mode
registers are not accessible.
Added a flow of exiting clock gating mode
to avoid the driver reload failure.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073731.3C81BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not hibernation nor partial power down are supported,
port resume is done using the clock gating programming flow.
Adds a new flow of exiting clock gating when PC is
resumed.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073723.BA0FEA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not hibernation nor partial power down are supported,
clock gating is used to save power.
Adds a new flow of entering clock gating when PC is
suspended.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073716.30C13A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When core is in clock gating state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
Added exit from clock gating state to avoid port
reset issue and process upper layer request properly.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073708.ADFC6A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates the implementation of exiting clock gating mode
when core receives port resume.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_exit_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073701.367E0A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates the implementation of entering clock gating mode
when core receives port suspend.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_enter_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073653.9F493A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds clock gating exit flow when set port feature
reset is received in suspended state.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073646.27217A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added exit from clock gating mode when wakeup interrupt
is detected. To exit from the clock gating
in device mode "dwc2_gadget_exit_clock_gating()"
function is used with rem_wakeup parameter 0. To exit
clock gating in host mode "dwc2_host_exit_clock_gating()"
with rem_wakeup parameter 1.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073630.EF2CEA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If core doesn't support hibernation or partial power
down power saving options, power can still be saved
using clock gating on all the clocks.
- Added entering clock gating state from USB_SUSPEND
interrupt.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073623.65355A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added device clock gating support functions according
programming guide.
Moved "bus_suspended" flag to "dwc2_hsotg" struct because
we need to set that flag while entering to clock gating
in case when the driver is built in peripheral mode.
Added function names:
dwc2_gadget_enter_clock_gating()
dwc2_gadget_exit_clock_gating()
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073607.F41E8A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This includes following Thunderbolt/USB4 changes for v5.13 merge window:
* Debugfs improvements
* Align the inter-domain (peer-to-peer) support with the USB4
inter-domain spec for better interoperability
* Add support for USB4 DROM and the new product descriptor
* More KUnit tests
* Detailed uevent for routers
* Few miscellaneous improvements
All these have been in linux-next without reported issues.
-----BEGIN PGP SIGNATURE-----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=RzJl
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.13 merge window
This includes following Thunderbolt/USB4 changes for v5.13 merge window:
* Debugfs improvements
* Align the inter-domain (peer-to-peer) support with the USB4
inter-domain spec for better interoperability
* Add support for USB4 DROM and the new product descriptor
* More KUnit tests
* Detailed uevent for routers
* Few miscellaneous improvements
All these have been in linux-next without reported issues.
* tag 'thunderbolt-for-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (24 commits)
thunderbolt: Hide authorized attribute if router does not support PCIe tunnels
thunderbolt: Add details to router uevent
thunderbolt: Unlock on error path in tb_domain_add()
thunderbolt: Add support for USB4 DROM
thunderbolt: Check quirks in tb_switch_add()
thunderbolt: Add KUnit tests for DMA tunnels
thunderbolt: Add KUnit tests for XDomain properties
net: thunderbolt: Align the driver to the USB4 networking spec
thunderbolt: Allow multiple DMA tunnels over a single XDomain connection
thunderbolt: Drop unused tb_port_set_initial_credits()
thunderbolt: Use dedicated flow control for DMA tunnels
thunderbolt: Add support for maxhopid XDomain property
thunderbolt: Add tb_property_copy_dir()
thunderbolt: Align XDomain protocol timeouts with the spec
thunderbolt: Use pseudo-random number as initial property block generation
thunderbolt: Do not re-establish XDomain DMA paths automatically
thunderbolt: Add more logging to XDomain connections
Documentation / thunderbolt: Drop speed/lanes entries for XDomain
thunderbolt: Decrease control channel timeout for software connection manager
thunderbolt: Do not pass timeout for tb_cfg_reset()
...
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmB0S50ACgkQSFkpgVDW
cbthMggAnH0oPq93dipS9g2WhHxmwKGJimWTFU82RxuuX6MefvllXEkWCHJdPplp
dyKhzaFQxFksR7GJ8UCoZg3wg0rk38suLiN+W+k9re6QaHPFWJiMEm83mN3/YaNn
stVLiuMRl+VIApIIWbf3MW8/a3j9N5oRI+MbqmvhcA4TFu3Z1xTe9xhs8eDtzeUV
cGI6JbrZr5Q3pcsvvZPwj2nFgjJ7eYum9Z1CsAopHyVnYu/NK2jh2+W+L37dUSan
cwUOIRoNvSYNHyXFVszOEmfxtTAKiISQ7L4+8tXr4X+qC8tUNd8Rw1ow5BAo8gh+
bBL8+NZVVGoTvNpYPhLLUHncE5Fn9Q==
=+ZMP
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Several Cadence3 improvements are introduced in v5.13-rc1:
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
* tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fixes issue with Configure Endpoint command
usb: cdnsp: remove redundant initialization of variable ret
usb: cdns3: delete repeated clear operations
usb: cdns3: Optimize DMA request buffer allocation
usb: cdns3: Use dma_pool_* api to alloc trb pool
usb: cdns3: fix static checker warning.
usb: cdns3: imx: mark cdns_imx_system_resume as __maybe_unused
usb: cdns3: trace: delete the trace parameter for request->trb
usb: cdns3: imx: add power lost support for system resume
usb: cdns3: add power lost support for system resume
Patch adds flag EP_UNCONFIGURED to detect whether endpoint was
unconfigured. This flag is set in cdnsp_reset_device after Reset Device
command. Among others this command disables all non control endpoints.
Flag is used in cdnsp_gadget_ep_disable to protect controller against
invoking Configure Endpoint command on disabled endpoint. Lack of this
protection in some cases caused that Configure Endpoint command completed
with Context State Error code completion.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
dma_alloc_coherent already zeroes out memory, so memset is not needed.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
dma_alloc_coherent() might fail on the platform with a small
DMA region.
To avoid such failure in cdns3_prepare_aligned_request_buf(),
dma_alloc_coherent() is replaced with dma_alloc_noncoherent()
to allocate aligned request buffer of dynamic length.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Allocation of DMA coherent memory in atomic context using
dma_alloc_coherent() might fail on platforms with smaller
DMA region.
To fix it, dma_alloc_coherent() is replaced with dma_pool
API to allocate a smaller chunk of DMA coherent memory for
TRB rings.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The patch c450e48eb570: "usb: cdns3: add power lost support for
system resume" from Feb 18, 2021, leads to the following static
checker warning:
drivers/usb/cdns3/core.c:551 cdns_resume()
error: uninitialized symbol 'ret'.
drivers/usb/cdns3/core.c
544
545 if (!role_changed) {
546 if (cdns->role == USB_ROLE_HOST)
547 ret = cdns_drd_host_on(cdns);
548 else if (cdns->role == USB_ROLE_DEVICE)
549 ret = cdns_drd_gadget_on(cdns);
"ret" is uninitialized at else branch.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The function cdns_imx_system_resume() may have no callers depending
on configuration, so it must be marked __maybe_unused to avoid
harmless warning:
drivers/usb/cdns3/cdns3-imx.c:378:12: warning:
'cdns_imx_system_resume' defined but not used [-Wunused-function]
378 | static int cdns_imx_system_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~
Fixes: 67982dfa59de ("usb: cdns3: imx: add power lost support for system resume")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
It is not correct using %pa to print virtual address of request->trb, and
it is hard to print its physical address due to the virtual address is
zero before using. It could use index (start_trb/end_trb) to know the
current trb position, so no matter virtual address or physical address
for request-trb is not so meaningful.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
imx need special handle when controller lost power
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Chunfeng Yun