Commit e34d65696d ("stmmac: create of compatible mdio bus for stmmac
driver") broke DW GMAC functionality on ARC AXS10x boards:
That's what happens on eth0 up:
--------------------------->8------------------------
| libphy: PHY stmmac-0:ffffffff not found
| eth0: Could not attach to PHY
| stmmac_open: Cannot attach to PHY (error: -19)
--------------------------->8------------------------
Simplest solution is to add PHY description in board's .dts.
And so we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Phil Reid <preid@electromag.com.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 4.5
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Since ezchip network driver was adapted to little endian architecture
this patch provides the corresponding arch/arc/{boot/dts,configs}/ updates so
we can switch over to this device-model/driver for OSCI platform.
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HIGHMEM support bumped the default memory size for nsim platform to 1G.
Thus total memory ended at the very edge of start of peripherals address
space. With linux link base shifted, memory started bleeding into
peripheral space which caused early boot bad_page spew !
Fixes: 29e332261d ("ARC: mm: HIGHMEM: populate high memory from DT")
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Current ARC SDP boards cannot reliably handle 1Gbit
Ethernet connections due to limitations in hardware.
To make sure networking is stable on the board we're
limiting phy to 100 Mbit.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all dtbs
in the tree for most arches with dts files (except powerpc for now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWO+HwAAoJEPr7XbWNvGHDFOoP/RcK4z5dtVQL2XRFbJBqRBZU
riMc4BZkwpcKGXjzZlMrLw+mg4vaoLKSIAGAsYkgdDOKbYphQQdVwDzN099Fzpzy
EE6K7Q+AW618z34AWdDjcpJYzSFnjAjYdh6JabohmKdPlxobR1RsKT+nRpDOGfeO
c1DmxAQ1Fiav+xAI4m0YUuyxQDUeFYC0mVcVPzRbWZj31Ia5BgIrvT+V7fM55CTb
dOAYWDHrfOw+yYI98sqZoSAb5H+E3UuY1ymBMhiP16Ot2vCyIKRYwhDokF9VYO/0
MpIMhCgv1jmE5NCbBeYSSJUePySvvnuyYe6HIaJQjV8KGEZ5C7c1iLMgtvov2KVI
bcSx6nPH/u5FuWIhWdMINPc50AQBAK/akYcgoCVjioVX+4WY2pqLvsXW2arEr//Z
XY3FUpgS6eI42HBsj4SxrGnzaRc2jPOs6yiANkywmHnpWcyvszCxUEvf0Mh0cbkm
diu31/owdpUO5imCe+ErtGVV3vY2VUMnbcm8J61pqL52OZNPLZUUEfktv1JCGW7y
cVdnlgeGSFuCbY4jUErvxtQGJQLFwf7Gg1U/VfFXX2iuQGAACB1KwxY5sR6P5Ghz
W6NvOTT36kaM9WGqn/bquOd6EmKcx9aZfgRLOkgV86Q/11gHKpuRjkrsth7rIJDI
97qkGiWl4t1Ll5T4StK8
=tGCy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A fairly large (by DT standards) pull request this time with the
majority being some overdue moving DT binding docs around to
consolidate similar bindings.
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
dtbs in the tree for most arches with dts files (except powerpc for
now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options"
* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
MAINTAINERS: update DT binding doc locations
devicetree: add Sigma Designs vendor prefix
of: simplify arch_find_n_match_cpu_physical_id() function
Documentation: arm: Fixed typo in socfpga fpga mgr example
Documentation: devicetree: fix reference to legacy wakeup properties
Documentation: devicetree: standardize/consolidate on "wakeup-source" property
drivers: of: removing assignment of 0 to static variable
xtensa: enable building of all dtbs
mips: enable building of all dtbs
metag: enable building of all dtbs
metag: use common make variables for dtb builds
h8300: enable building of all dtbs
arm64: enable building of all dtbs
arm: enable building of all dtbs
arc: enable building of all dtbs
arc: use common make variables for dtb builds
of: add config option to enable building of all dtbs
of/fdt: fix error checking for earlycon address
of/overlay: add missing of_node_put
of/platform: add missing of_node_put
...
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Use dtb-y and always make variables to build dtbs instead of explicit
dtbs rule. This is in preparation to support building all dtbs.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
With up-to-date FPGA builds ARC cores are supposed to correctly operate
even with 90 MHz clock (which is a target frequency for AXS103 release).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-linux-dev@synopsys.com
- CONFIG_ARC_UBOOT_SUPPORT to handle arguments passed in r0, r1, r2
- CONFIG_DEVTMPFS_MOUNT for mouting rootfs since it uses external cpio
for rootfs
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ruud Derwig <rderwig@synopsys.com>
[vgupta: folded the Main baord DT files for smp/up into one]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
To avoid duplicating the MB DTS file, move the MB intc entry into cpu
card specific file
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As DW Mobile Storage databook says it's required to use "Hold Register"
if card is enumerated in SDR12 or SDR25 modes.
It means we need to act in the same way as in Altera's Socfpga
implementation - set "use hold reg" bit in commad.
Note that for upstream proper solution would be to remove
dw_mci_pltfm_prepare_command() at all and set the bit right in
dw_mci_prepare_command() for all platforms.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Earlycon calculates UART clock as "BASE_BAUD * 16". In case of ARC
"BASE_BAUD" is calculated dynamically in runtime, basically it is an
alias to arc_early_base_baud(), which in turn just does
"arc_base_baud/16".
8250 UART on AXS/SDP board uses 33.3MHz clock source which is set in
"arc_base_baud" with this change.
Additional compatibility string "snps,arc-sdp" is introduced as well
because there're different flavours of AXS boards but they all share the
same motherboard and so it's possible to re-use the same code for
motherbord even if CPU daughterboard changes.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The AXS10x platforms consist of a mainboard with peripherals,
on which several daughter cards can be placed. The daughter cards
typically contain a CPU and memory.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Remove remanants of legacy ARC FPGA platforms (AA4, ML509...)
* Only nsim simulation platform is left, rename platform accordingly
* AA4 DT stuff is compatible with nsim for ARC700 so rename it too
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Instead of using magic number in the code the patch provides
DW_DMA_MAX_NR_MASTERS constant.
While here, restrict the reading of data width array by amount of the actual
number of AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This allows the sdplite/Zebu images to run on OSCI simulation platform
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.14, 3.16
There are certain test configuration of virtual platform which don't
have any real console device (uart/pgu). So add tty0 as a fallback console
device to allow system to boot and be accessible via telnet
Otherwise with ttyS0 as only console, but 8250 disabled in kernel build,
init chokes.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.14, 3.16
This reverts commit 9da433c0a0.
Vineet writes:
Could you please revert this single patch from tty-next for 3.17 as the
needed core changes are not yet finalized.
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With recent improvements to serial/of core from Grant and Rob,
stdout-path alone suffices for setting up earlycon/console.
arc_uart driver is already equipped to handle that, switch the DT now.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlier CONFIG_SERIAL_ARC_CONSOLE would unconditionally enable the
legacy ARC UART based early console even if platform lacked that UART
(e.g. nSIM OSCI platform).
So a multi-platform image containing the 2 UART drivers won't work.
Fix that by probing the driver only if "earlyprintk=ttyARC0" is present
in cmdline.
Reported-by: Chuck Jordan <cjordan@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Despite the switch to right UART driver (prev patch), serial console
still doesn't work due to missing CONFIG_SERIAL_OF_PLATFORM
Also fix the default cmdline in DT to not refer to out-of-tree
ARC framebuffer driver for console.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.13, 3.14
Cc: Francois Bedard <Francois.Bedard@synopsys.com>
The Synopsys APB DW UART has a couple of special features that are not
in the System C model. In 3.8, the 8250_dw driver didn't really use these
features, but from 3.9 onwards, the 8250_dw driver has become incompatible
with our model.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.13, 3.14
Cc: Francois Bedard <Francois.Bedard@synopsys.com>
This adds basic perf support for ARC700 cores. Most PERF_COUNT_HW* events
are supported now.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Device tree and Kconfig updates for GPIO and pinctrl drivers.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
corresponding drivers (net/ethernet/arc/*, irqctl/irq-tb10x.c) have now
been merged into your tree.
Ideally these shd have been part of same submissions, oh well...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QgUU
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull second set of ARC architecture updates from Vineet Gupta:
"Couple of Platform updates (Device Tree files primarily) given that
the corresponding drivers (net/ethernet/arc/*, irqctl/irq-tb10x.c)
have now been merged into your tree.
Ideally these shd have been part of same submissions, oh well..."
* tag 'arc-v3.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [TB10x] Updates for irqchip driver
ARC: [plat-arcfpga] Enable arc_emac for ARCAngle4 Board
Device tree and Kconfig updates for irqchip driver.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch makes the SDA hold time configurable through device tree.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com> for arch/arc bits
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The TB10x platform port includes a custom mechanism using to set up
default pin controller configurations using abilis,simple-default
pin configurations of nodes compatible with abilis,simple-pinctrl. This
mechanism is redundant with the Linux standard "default" pin
configuration, see commit ab78029ecc
"drivers/pinctrl: grab default handles from device core".
This patch removes the TB10x custom mechanism in favour of the Linux
standard.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This adds support for an ARC Virtual Platform. This platform is based on the
System C standard promoted by the OSCI (Open System C Initiative) and uses
nSIM to simulate the ARC CPU core itself.
Users can build a virtual SoC by combining System C models of peripherals
and CPU cores.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original device tree was written using a slightly different
implementation of the fixed-factor-clock device tree binding. The
compatible string must be modified in order to be compatible with the
new implementation.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These are the device tree files for the Abilis Systems TB100 and TB101 ICs and
their respective development kit PCBs. These files are committed in preparation
of the following patch set which adds support for these chips to the ARC
platform.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Currently, for every ARC kernel build I see the following:
--------------->8-----------------
DTB arch/arc/boot/dts/angel4.dtb.S
AS arch/arc/boot/dts/angel4.dtb.o
LD arch/arc/boot/dts/built-in.o
rm arch/arc/boot/dts/angel4.dtb.S <-- forces rebuild next iter
CHK kernel/config_data.h
--------------->8-----------------
This is because *.dts.S is intermediate file in dtb generation and is by
default deleted by make which needs a ".SECONDARY" hint to NOT do so.
This could have ideally been done in scripts/Makefile.lib - for benefit
of all, however .SECONDARY doesn't seem to work with wildcards.
Thanks to Stephen for suggesting .SECONDARY (vs .PRECIOUS) and making
that work using a non wildcard version in arch makefile.
Thanks to James Hogan for pointing out that *.dtb.S now needs to be
added to clean-files
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The existing uImage target always generates gzip compressed image which
drags bootup for some very slow FPGA customer boards.
So introduce seperate make targets:uImage.{bin,gz} with uncompressed
being default. Also tie gz generation to CONFIG_KERNEL_GZIP, which a
platform can select in it's Kconfig if it wishes gz to be default.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* arc-uart platform device now populated dynamically, using
of_platform_populate() - applies to any other device whatsoever.
* uart in turn requires incore arc-intc to be also present in DT
* A irq-domain needs to be instantiated for IRQ requests by DT probed
device (e.g. arc-uart)
TODO: switch over to linear irq domain once all devs have been
transitioned to DT
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Alexey Brodkin