When we get an unexpected Block Ack Request frame, the BAID from
the hardware will be invalid, and we'll pass it to mac80211 for
further handling (sending a delBA action frame.)
Add a comment explaining that, in case anyone looks in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to firmware design considerations, move to wide ID for
all commands.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in making this an out-of-line function
since it just calls a single other function with a few
changed parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Log group as well. Remove 0x prefix to match TX logging.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will be used by more than MVM, so move it to iwlwifi
While at it, rename WRD_METHOD to the more appropriate
WRDD_METHOD and add some documentation.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For automatic testing packet injection can be useful.
Support injection through debugfs.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement support for RRM by adding an option to configure the scan
dwell time and reporting scan start time and BSS detection time, and
Advertise support for these features.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On default queue we will not receive frame release notification,
but the BAR itself.
Upon receiving the BAR driver should look at the NSSN and adjust
window accordingly.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There was recently a Full AP mode feature added where hostap adds
the station at auth stage, and not assoc.
However, when running with legacy hostapd, we get the auth response
before station was added, and tx_skb_non_sta fails to allocate
a queue, resulting in a complete failure of association.
Take care of this situation as well.
Add a warning when no valid queue is returned at all and make mvm
drop the packet instead of passing it on.
Refactor the function a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 9000 family products we added an option to let the OEM fuse the
mac address via registers. If these registers are zeroed we use the OTP
address instead. Make sure that the address provided by the OEM is valid
and, if not, fall back to the OTP address as well.
Fixes: commit 17c867bfe8 ("iwlwifi: add support for getting HW address from CSR")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
enable MU-MIMO air sniffer if it's supported by the NIC
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When comparing command IDs, the group should be taken
into account so the same command/notification from a
different group doesn't trigger anything unexpected.
Fix this by comparing to the wide ID.
Fixes: commit 1738d60b31 ("iwlwifi: mvm: handle RX MPDUs separately")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use skb_queue_empty() and not skb_peek_tail() to check for
empty list.
Avoid a redundant check as well - loop will take care of it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If adapter is null the error exit path in mwifiex_shutdown_sw is
to down the semaphore sem and print some debug via mwifiex_dbg.
However, passing a NULL adapter to mwifiex_dbg causes a null
pointer deference when accessing adapter->dev. This fix checks
for a null adapter at the start of the function and to exit
without the need to up the semaphore and we also skip the debug
to avoid the null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
smatch reports:
sta_cmdresp.c:1053 mwifiex_create_custom_regdomain() warn: possible memory leak of 'regd'
Indeed, mwifiex_create_custom_regdomain() returns NULL in the
case that channel is missing in the TLV without freeing regd.
Moreover, some other error paths in this function return ERR_PTR
values which are assigned without checking to the regd field in
the mwifiex_adapter struct. The latter is only null-checked where
used.
Fix by freeing regd in the error path, and only update
priv->adapter->regd if the returned pointer is valid.
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This powers down the 8192e correctly, or at least to the point where
the firmware will load again, when reloading the driver module.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support
* general cleanups and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SrvZ
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-09-15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support
* general cleanups and improvements
Alexei Starovoitov says:
====================
ip_tunnel: add collect_md mode to IPv4/IPv6 tunnels
Similar to geneve, vxlan, gre tunnels implement 'collect metadata' mode
in ipip, ipip6, ip6ip6 tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
the test creates 3 namespaces with veth connected via bridge.
First two namespaces simulate two different hosts with the same
IPv4 and IPv6 addresses configured on the tunnel interface and they
communicate with outside world via standard tunnels.
Third namespace creates collect_md tunnel that is driven by BPF
program which selects different remote host (either first or
second namespace) based on tcp dest port number while tcp dst
ip is the same.
This scenario is rough approximation of load balancer use case.
The tests check both traditional tunnel configuration and collect_md mode.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
extend existing tests for vxlan, geneve, gre to include IPIP tunnel.
It tests both traditional tunnel configuration and
dynamic via bpf helpers.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve tunnels allow IPIP6 and IP6IP6 tunnels
to operate in 'collect metadata' mode.
Unlike ipv4 code here it's possible to reuse ip6_tnl_xmit() function
for both collect_md and traditional tunnels.
bpf_skb_[gs]et_tunnel_key() helpers and ovs (in the future) are the users.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve tunnels allow IPIP tunnels to
operate in 'collect metadata' mode.
bpf_skb_[gs]et_tunnel_key() helpers can make use of it right away.
ovs can use it as well in the future (once appropriate ovs-vport
abstractions and user apis are added).
Note that just like in other tunnels we cannot cache the dst,
since tunnel_info metadata can be different for every packet.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure. This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p = { ... };
@ok@
identifier r.i;
struct net_device e;
position p;
@@
e.netdev_ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct net_device_ops i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
3401 931 44 4376 1118 net/l2tp/l2tp_eth.o
and after the change it is:
text data bss dec hex filename
3993 347 44 4384 1120 net/l2tp/l2tp_eth.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure. This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p = { ... };
@ok@
identifier r.i;
struct net_device e;
position p;
@@
e.netdev_ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct net_device_ops i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
21623 1316 40 22979 59c3
drivers/net/ethernet/synopsys/dwc_eth_qos.o
and after the change it is:
text data bss dec hex filename
22199 724 40 22963 59b3
drivers/net/ethernet/synopsys/dwc_eth_qos.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure. This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p = { ... };
@ok@
identifier r.i;
struct net_device e;
position p;
@@
e.netdev_ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct net_device_ops i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
7995 848 8 8851 2293
drivers/net/ethernet/hisilicon/hip04_eth.o
and after the change it is:
text data bss dec hex filename
8571 256 8 8835 2283
drivers/net/ethernet/hisilicon/hip04_eth.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer used after e0d56fdd73 ("net: l3mdev: remove redundant calls")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer used after d66f6c0a8f ("net: ipv4: Remove l3mdev_get_saddr")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With large BDP TCP flows and lossy networks, it is very important
to keep a low number of skbs in the write queue.
RACK and SACK processing can perform a linear scan of it.
We should avoid putting any payload in skb->head, so that SACK
shifting can be done if needed.
With this patch, we allow to pack ~0.5 MB per skb instead of
the 64KB initially cooked at tcp_sendmsg() time.
This gives a reduction of number of skbs in write queue by eight.
tcp_rack_detect_loss() likes this.
We still allow payload in skb->head for first skb put in the queue,
to not impact RPC workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* preparation for new a000 HW continues
* some DQA improvements
* add support for GMAC
* add support for 9460, 9270 and 9170 series
mwifiex
* support random MAC address for scanning
* add HT aggregation support for adhoc mode
* add custom regulatory domain support
* add manufacturing mode support via nl80211 testmode interface
bcma
* support BCM53573 series of wireless SoCs
bitfield.h
* add FIELD_PREP() and FIELD_GET() macros
mt7601u
* convert to use the new bitfield.h macros
brcmfmac
* add support for bcm4339 chip with modalias sdio:c00v02D0d4339
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX2rF7AAoJEG4XJFUm622bD3EH/icZDT7vVxnb0VPP8jAScA4h
bMNrI3iFxnPohO8Rzp+edWSdxEZoxwrBVk/6BHXO9PHHZwPX7/b8/OOXmLWB2X1c
ffj1jt83RENcsZFvd5OJfDYxIq89uOkWybdD6nIUd3umKC9KeFOI5nCju31fEZrQ
ZptqvKGIV36bbx07K8Y/PQRL2SA6T+09WqvuljLHZD5hfPGZ+GWXV2p+HAm3Moos
iy6HUx5+pYfC+zlcmvJvL47Wxj+HppS/48ujyQ68DD2UkjOtF620YJjVy3o+njip
GNJtCgWFDp2ar3uvRP2BfBd9FtseDTKsKusxJQvNGoSR0ON+uGIzURCznQ+2PCM=
=FyXw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-09-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.9
Major changes:
iwlwifi
* preparation for new a000 HW continues
* some DQA improvements
* add support for GMAC
* add support for 9460, 9270 and 9170 series
mwifiex
* support random MAC address for scanning
* add HT aggregation support for adhoc mode
* add custom regulatory domain support
* add manufacturing mode support via nl80211 testmode interface
bcma
* support BCM53573 series of wireless SoCs
bitfield.h
* add FIELD_PREP() and FIELD_GET() macros
mt7601u
* convert to use the new bitfield.h macros
brcmfmac
* add support for bcm4339 chip with modalias sdio:c00v02D0d4339
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
mlx5e Order-0 pages for Striding RQ
In this series, we refactor our Striding RQ receive-flow to always use
fragmented WQEs (Work Queue Elements) using order-0 pages, omitting the
flow that allocates and splits high-order pages which would fragment
and deplete high-order pages in the system.
The first patch gives a slight degradation, but opens the opportunity
to using a simple page-cache mechanism of a fair size.
The page-cache, implemented in patch 3, not only closes the performance
gap but even gives a gain.
In patch 2 we re-organize the code to better manage the calls for
alloc/de-alloc pages in the RX flow.
Series generated against net-next commit:
bed806cb26 "Merge branch 'mlxsw-ethtool'"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reallocating and mapping pages for RX data-path,
recycle already used pages in a per ring cache.
Performance tests:
The following results were measured on a freshly booted system,
giving optimal baseline performance, as high-order pages are yet to
be fragmented and depleted.
We ran pktgen single-stream benchmarks, with iptables-raw-drop:
Single stride, 64 bytes:
* 4,739,057 - baseline
* 4,749,550 - order0 no cache
* 4,786,899 - order0 with cache
1% gain
Larger packets, no page cross, 1024 bytes:
* 3,982,361 - baseline
* 3,845,682 - order0 no cache
* 4,127,852 - order0 with cache
3.7% gain
Larger packets, every 3rd packet crosses a page, 1500 bytes:
* 3,731,189 - baseline
* 3,579,414 - order0 no cache
* 3,931,708 - order0 with cache
5.4% gain
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manage the allocation and deallocation of mapped RX pages only
through dedicated API functions.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve the memory consumption scheme, we omit the flow that
demands and splits high-order pages in Striding RQ, and stay
with a single Striding RQ flow that uses order-0 pages.
Moving to fragmented memory allows the use of larger MPWQEs,
which reduces the number of UMR posts and filler CQEs.
Moving to a single flow allows several optimizations that improve
performance, especially in production servers where we would
anyway fallback to order-0 allocations:
- inline functions that were called via function pointers.
- improve the UMR post process.
This patch alone is expected to give a slight performance reduction.
However, the new memory scheme gives the possibility to use a page-cache
of a fair size, that doesn't inflate the memory footprint, which will
dramatically fix the reduction and even give a performance gain.
Performance tests:
The following results were measured on a freshly booted system,
giving optimal baseline performance, as high-order pages are yet to
be fragmented and depleted.
We ran pktgen single-stream benchmarks, with iptables-raw-drop:
Single stride, 64 bytes:
* 4,739,057 - baseline
* 4,749,550 - this patch
no reduction
Larger packets, no page cross, 1024 bytes:
* 3,982,361 - baseline
* 3,845,682 - this patch
3.5% reduction
Larger packets, every 3rd packet crosses a page, 1500 bytes:
* 3,731,189 - baseline
* 3,579,414 - this patch
4% reduction
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Fixes: bc77b240b3 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CONFIG_AF_RXRPC_IPV6 and make the IPv6 support code conditional on it.
This is then made conditional on CONFIG_IPV6.
Without this, the following can be seen:
net/built-in.o: In function `rxrpc_init_peer':
>> peer_object.c:(.text+0x18c3c8): undefined reference to `ip6_route_output_flags'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin says:
====================
net-next: dsa: add QCA8K support
This series is based on the AR8xxx series posted by Matthieu Olivari in may
2015. The following changes were made since then
* fixed the nitpicks from the previous review
* updated to latest API
* turned it into an mdio device
* added callbacks for fdb, bridge offloading, stp, eee, port status
* fixed several minor issues to the port setup and arp learning
* changed the namespacing as this driver to qca8k
The driver has so far only been tested on qca8337/N. It should work on other QCA
switches such as the qca8327 with minor changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains initial support for the QCA8337 switch. It
will detect a QCA8337 switch, if present and declared in the DT.
Each port will be represented through a standalone net_device interface,
as for other DSA switches. CPU can communicate with any of the ports by
setting an IP@ on ethN interface. Most of the extra callbacks of the DSA
subsystem are already supported, such as bridge offloading, stp, fdb.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device-tree binding for ar8xxx switch families.
Cc: devicetree@vger.kernel.org
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/dsa/bcm_sf2.c:963:19: warning:
symbol 'bcm_sf2_io_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb replaces another one in ooo queue, I forgot to also
update tp->ooo_last_skb as well, if the replaced skb was the last one
in the queue.
To fix this, we simply can re-use the code that runs after an insertion,
trying to merge skbs at the right of current skb.
This not only fixes the bug, but also remove all small skbs that might
be a subset of the new one.
Example:
We receive segments 2001:3001, 4001:5001
Then we receive 2001:8001 : We should replace 2001:3001 with the big
skb, but also remove 4001:50001 from the queue to save space.
packetdrill test demonstrating the bug
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
+0.100 < . 1:1(0) ack 1 win 1024
+0 accept(3, ..., ...) = 4
+0.01 < . 1001:2001(1000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001>
+0.01 < . 1001:3001(2000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001 1001:3001>
Fixes: 9f5afeae51 ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang says:
====================
mediatek: add enhancement into the existing reset flow
Current driver only resets DMA used by descriptor rings which
can't guarantee it can recover all various kinds of fatal
errors, so the patch
1) tries to reset the underlying hardware resource from scratch on
Mediatek SoC required for ethernet running.
2) refactors code in order to the reusability of existing code.
3) considers handling for race condition between the reset flow and
callbacks registered into core driver called about hardware accessing.
4) introduces power domain usage to hardware setup which leads to have
cleanly and completely restore to the state as the initial.
Changes since v1:
- fix the build error with module built causing undefined symbol for
pinctrl_bind_pins, so using pinctrl_select_state instead accomplishes
the pin mux setup during the reset process.
====================
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sharon Dvir