We already have it for chv, but was missing for bdw.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that sanity prevails and we have the clean split between software
init and starting the engines we can drop all the "have we allocate
this struct already?" nonsense.
Execlist code could benefit quite a bit more still, but that's for
another patch.
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We can do this.
And now there's finally the clean split between software setup and
hardware setup I kinda wanted since multi-ring support was merged
aeons ago. It only took almost 5 years.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this all the ->init_hw hooks really only set up hw state needed
to start the ring, all the software state setup and memory/buffer
allocations happen beforehand.
v2: We need to call intel_init_pipe_control after the ring init since
otherwise engine->dev is NULL and it falls over. Currently that's
now after the hw ring is enabled but a) we'll be fine as long as no
one submits a batch b) this will change soon.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is (mostly, some exceptions that need fixing) the hw setup
function which starts the ring. And not the function which allocates
all the resources.
Make this clear by giving it a better name.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are numerous places in the code where the driver's idea of
how much space is left in a ring is updated using the driver's
latest notions of the positions of 'head' and 'tail' for the ring.
Among them are some that update one or both of these values before
(re)doing the calculation. In particular, there are four different
places in the code where 'last_retired_head' is copied to 'head'
and then set to -1; and two of these do not have a guard to check
that it has actually been updated since last time it was consumed,
leaving the possibility that the dummy -1 can be transferred from
'last_retired_head' to 'head', causing the space calculation to
produce 'impossible' results (previously seen on Android/VLV).
This code therefore consolidates all the calculation and updating of
these values, such that there is only one place where the ring space
is updated, and it ALWAYS uses (and consumes) 'last_retired_head' if
(and ONLY if) it has been updated since the last call.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The used space in a ring is given by the cyclic distance from the
consumer (HEAD) to the producer (TAIL), i.e. ((tail-head) MOD size);
conversely, the available space in a ring is the cyclic distance
from the producer to the consumer, MINUS the amount reserved for a
"gap" that is supposed to guarantee that the producer never catches
up with or overruns the consumer. Note that some GEN h/w requires
that TAIL never approach to within one cacheline of HEAD, so the gap
is usually set to twice the cacheline size to ensure this.
While the existing code gives the correct answer for correct inputs,
if the producer HAS overrun into the reserved space, the result can
be a value larger than the maximum valid value (size-reserved). We
can improve this by reorganising the calculation, so that in the
event of overrun the result will be negative rather than over-large.
This means that the commonly-used test (available >= required)
will then reject further writes into the ring after an overrun,
giving some chance that we can recover from or at least diagnose
the original problem; whereas allowing more writes would likely both
confuse the h/w and destroy the evidence of what went wrong.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It makes a lot more sense (and makes future seqno -> request conversion patches
simpler) to fill in the 'ring' field of the request structure at the point of
creation rather than submission. Given that the request structure is assigned by
ring specific code and thus is locked to a ring from the start, there really is
no reason to defer this assignment.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no longer any need to retrieve a seqno value from an i915_add_request()
call. The calling code already knows which request structure is being processed
(it can only be ring->OLR). And as the request itself is now used in preference
to the basic seqno value, the latter is now redundant in this situation.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated i915_wait_seqno() to take a request structure instead of a seqno value
and renamed it accordingly. Internally, it just pulls the seqno out of the
request and calls on to __wait_seqno() as before. However, all the code further
up the stack is now simplified as it can just pass the request object straight
through without having to peek inside.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Squash in hunk from an earlier patch which was rebased
wrongly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The OLS value is now obsolete. Exactly the same value is guarateed to be always
available as PLR->seqno. Thus it is safe to remove the OLS completely. And also
to rename the PLR to OLR to keep the 'outstanding lazy ...' naming convention
valid.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to use request structures everywhere that seqno values were
previously used. This means saving pointers to structures in places that used to
be simple integers. In turn, that means that the target structure now needs much
more stringent lifetime tracking. That is, it must not be freed while some other
random object still holds a pointer to it.
To achieve this tracking, a reference count needs to be added. Whenever a
pointer to the structure is saved away, the count must be incremented and the
free must only occur when all references have been released.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The aim is to replace seqno values with request structures. A step along the way
is to switch to using the PLR in preference to the OLS. That requires the PLR to
only be valid when and only when the OLS is also valid. I.e., the two must be
kept in lock step. Then, code which was using the OLS can be safely switched
over to using the PLR instead.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the deprecation of UMS, and by association DRI1, we have a tough
choice when updating the ring access routines. We either rewrite the
DRI1 routines blindly without testing (so likely to be broken) or take
the liberty of declaring them no longer supported and remove them
entirely. This takes the latter approach.
v2: Also remove the DRI1 sarea updates
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fix rebase conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as with the context, pinning to GGTT regardless is harmful (it
badly fragments the GGTT and can even exhaust it).
Unfortunately, this case is also more complex than the previous one
because we need to map and access the ringbuffer in several places
along the execbuffer path (and we cannot make do by leaving the
default ringbuffer pinned, as before). Also, the context object
itself contains a pointer to the ringbuffer address that we have to
keep updated if we are going to allow the ringbuffer to move around.
v2: Same as with the context pinning, we cannot really do it during
an interrupt. Also, pin the default ringbuffers objects regardless
(makes error capture a lot easier).
v3: Rebased. Take a pin reference of the ringbuffer for each item
in the execlist request queue because the hardware may still be using
the ringbuffer after the MI_USER_INTERRUPT to notify the seqno update
is executed. The ringbuffer must remain pinned until the context save
is complete. No longer pin and unpin ringbuffer in
populate_lr_context() - this transient address is meaningless and the
pinning can cause a sleep while atomic.
v4: Moved ringbuffer pin and unpin into the lr_context_pin functions.
Downgraded pinning check BUG_ONs to WARN_ONs.
v5: Reinstated WARN_ONs for unexpected execlist states. Removed unused
variable.
Issue: VIZ-4277
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Following the legacy ring submission example, update the
ring->init_context() hook to support the execlist submission mode.
v2: update to use the new workaround macros and cleanup unused code.
This takes care of both bdw and chv workarounds.
v2.1: Add missing call to init_context() during deferred context creation.
v3: Split init_context (emit) in legacy/lrc modes. For lrc, get the ringbuf
from the context (Mika/Daniel).
v4: Merge init_context interfaces back, the legacy mode only needs the ring,
but the lrc mode needs the ring and context (Mika).
Issue: VIZ-4092
Issue: GMIN-3475
Change-Id: Ie3d093b2542ab0e2a44b90460533e2f979788d6c
Cc: Deepak S <deepak.s@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Align function paramater lists properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaDisablePartialInstShootdown:chv and
WaDisableThreadStallDopClockGating:chv are related to the same
register so combine them.
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-WaDisableDopClockGating:chv
-WaDisableSamplerPowerBypass:chv
-WaDisableGunitClockGating:chv
-WaDisableFfDopClockGating:chv
-WaDisableDopClockGating:chv
v2: Remove pre-production WA instead of restricting them
based on revision id (Ville)
For: VIZ-4090
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a ring failed to initialise for any reason then the error path would try to
clean up all rings including those that had not yet been allocated. The ring
clean up code did a check that the ring was valid before starting its work.
Unfortunately, that was after it had already dereferenced the ring to obtain a
dev_private pointer.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- suspend/resume/freeze/thaw unification from Imre
- wa list improvements from Mika&Arun
- display pll precomputation from Ander Conselvan, this removed the last
->mode_set callbacks, a big step towards implementing atomic modesets
- more kerneldoc for the interrupt code
- 180 rotation for cursors (Ville&Sonika)
- ULT/ULX feature check macros cleaned up thanks to Damien
- piles and piles of fixes all over, bug team seems to work!
* tag 'drm-intel-next-2014-10-24' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20141024
drm/i915: add comments on what stage a given PM handler is called
drm/i915: unify switcheroo and legacy suspend/resume handlers
drm/i915: add poweroff_late handler
drm/i915: sanitize suspend/resume helper function names
drm/i915: unify S3 and S4 suspend/resume handlers
drm/i915: disable/re-enable PCI device around S4 freeze/thaw
drm/i915: enable output polling during S4 thaw
drm/i915: check for GT faults in all resume handlers and driver load time
drm/i915: remove unused restore_gtt_mappings optimization during suspend
drm/i915: fix S4 suspend while switcheroo state is off
drm/i915: vlv: fix switcheroo/legacy suspend/resume
drm/i915: propagate error from legacy resume handler
drm/i915: unify legacy S3 suspend and S4 freeze handlers
drm/i915: factor out i915_drm_suspend_late
drm/i915: Emit even number of dwords when emitting LRIs
drm/i915: Add rotation support for cursor plane (v5)
drm/i915: Correctly reject invalid flags for wait_ioctl
drm/i915: use macros to assign mmio access functions
drm/i915: only run hsw_power_well_post_enable when really needed
...
Ok, new attempt, this time around with full ppgtt disabled again.
drm-intel-next-2014-10-03:
- first batch of skl stage 1 enabling
- fixes from Rodrigo to the PSR, fbc and sink crc code
- kerneldoc for the frontbuffer tracking code, runtime pm code and the basic
interrupt enable/disable functions
- smaller stuff all over
drm-intel-next-2014-09-19:
- bunch more i830M fixes from Ville
- full ppgtt now again enabled by default
- more ppgtt fixes from Michel Thierry and Chris Wilson
- plane config work from Gustavo Padovan
- spinlock clarifications
- piles of smaller improvements all over, as usual
* tag 'drm-intel-next-2014-10-03-no-ppgtt' of git://anongit.freedesktop.org/drm-intel: (114 commits)
Revert "drm/i915: Enable full PPGTT on gen7"
drm/i915: Update DRIVER_DATE to 20141003
drm/i915: Remove the duplicated logic between the two shrink phases
drm/i915: kerneldoc for interrupt enable/disable functions
drm/i915: Use dev_priv instead of dev in irq setup functions
drm/i915: s/pm._irqs_disabled/pm.irqs_enabled/
drm/i915: Clear TX FIFO reset master override bits on chv
drm/i915: Make sure hardware uses the correct swing margin/deemph bits on chv
drm/i915: make sink_crc return -EIO on aux read/write failure
drm/i915: Constify send buffer for intel_dp_aux_ch
drm/i915: De-magic the PSR AUX message
drm/i915: Reinstate error level message for non-simulated gpu hangs
drm/i915: Kerneldoc for intel_runtime_pm.c
drm/i915: Call runtime_pm_disable directly
drm/i915: Move intel_display_set_init_power to intel_runtime_pm.c
drm/i915: Bikeshed rpm functions name a bit.
drm/i915: Extract intel_runtime_pm.c
drm/i915: Remove intel_modeset_suspend_hw
drm/i915: spelling fixes for frontbuffer tracking kerneldoc
drm/i915: Tighting frontbuffer tracking around flips
...
The number of DWords should be even when doing ring emits as
command sequences require QWord alignment.
There was some discussion about the maximum length of the MI_LRI
command. Quoting Mika
"I did some test with bdw:
"The maximum is 128 writes, resulting the 8 bit length
field of the command being 0xff, thus following the spec.
The 128'th write went through.
"Perhaps the max command length is then less in older gens?
"Perhaps WARN_ON(x > 128) in MI_LOAD_REGISTER_IMM would be in place
but one needs minor tweak to command parser a bit also then.
#define I915_MAX_WA_REGS 16
keeps us safe for now atleast."
Ville commented that on pre-gen6 the length field seems to be
restricted to 0x3f though. So for all cases we should be ok.
v2: user LRI variant that can write multiple regs in one go (Damien).
We can simply insert one NOP at the end instead of one per register write.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add a summary of the MI_LRI length discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we build the workaround list in ring initialization
and decouple it from the actual writing of values, we
gain the ability to decide where and how we want to apply
the values.
The advantage of this will become more clear when
we need to initialize workarounds on older gens where
it is not possible to write all the registers through ring
LRIs.
v2: rebase on newest bdw workarounds
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[danvet: Resolve tiny conflict in comments and ocd alignments a bit.]
[danvet2: Remove bogus force_wake_get call spotted by Paulo and QA.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's clean this a bit
v2: Rebase after other Mika's patch that removed some BDW production workarounds.
v3: Removed stepping info.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I've sent the first pull request to Dave and I expect his request
for a merge tree any second now ;-)
More seriously I have some pending patches for 3.19 that depend upon
both trees, hence backmerge. Conflicts are all trivial.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
v2: Of course I've forgotten the fixup script for the silent conflict.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The sw cache clean on BDW is a tempoorary workaround because we cannot
set cache clean on blt ring with risk of hungs. So we are doing the cache clean on sw.
However we are doing much more than needed. Not only when using blt ring.
So, with this extra w/a we minimize the ammount of cache cleans and call it only
on same cases that it was being called on gen7.
The traditional FBC Cache clean happens over LRI on BLT ring when there is a
frontbuffer touch happening. frontbuffer tracking set fbc_dirty variable
to let BLT flush that it must clean FBC cache.
fbc.need_sw_cache_clean works in the opposite information direction
of ring->fbc_dirty telling software on frontbuffer tracking to perform
the cache clean on sw side.
v2: Clean it a little bit and fully check for Broadwell instead of gen8.
v3: Rebase after frontbuffer organization.
v4: Wiggle confused me. So fixing v3!
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following sets the AsyncFlip performance mode for everything above
Gen6:
commit 4790cb36b3eede8fb0cca529dc1d31b9936fa24b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jan 20 16:11:20 2013 +0000
drm/i915: Disable AsyncFlip performance optimisations
Starting from Gen9 the MI_MODE register layout changes and doesn't
include the above bit.
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
as these have been fixed in production hw and hurt performance
if applied.
v2: adjust requested ring space (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83482
Tested-by: zhoujian <jianx.zhou@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yet another place that wasn't properly transformed when implementing
SOix. While at it convert the checks to WARN_ON on gen5+ (since we
don't have UMS potentially doing stupid things on those platforms).
And also add the corresponding checks to the put functions (again with
a WARN_ON) for gen5+.
v2: Drop the WARNINGS in the irq_put functions (including the existing
one for vebox), Chris convinced me that they're not that terribly
useful.
v3: Don't forget about execlist code.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: "Volkin, Bradley D" <bradley.d.volkin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
gen6 and earlier conflate address space selection (ppgtt vs ggtt) with
the security bit (i.e. only privileged batches were allowed to run from
ggtt). From Haswell only, you are able to select the security bit
separate from the address space - and we always requested to use ppgtt.
This breaks the golden render state batch execution with full-ppgtt as
that is only present in the global GTT and more generally any secure
batch that is not colocated in the ppgtt and ggtt. So we need to
disable the use of the ppgtt selector bit for secure batches, or else we
hang immediately upon boot and thence after every GPU reset...
v2: Only HSW differentiates between secure dispatch and ggtt, so simply
ignore the differentiation and always use secure==ggtt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rectify commit message as noted by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
One small change I forgot to make in
commit c4d69da167
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Sep 8 14:25:41 2014 +0100
drm/i915: Evict CS TLBs between batches
was to update the copy width for the compact BLT copy instruction.
Reported-by: Thomas Richter <thor@math.tu-berlin.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Richter <thor@math.tu-berlin.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Tested-by: Thomas Richter <thor@math.tu-berlin.de>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Running igt, I was encountering the invalid TLB bug on my 845g, despite
that it was using the CS workaround. Examining the w/a buffer in the
error state, showed that the copy from the user batch into the
workaround itself was suffering from the invalid TLB bug (the first
cacheline was broken with the first two words reversed). Time to try a
fresh approach. This extends the workaround to write into each page of
our scratch buffer in order to overflow the TLB and evict the invalid
entries. This could be refined to only do so after we update the GTT,
but for simplicity, we do it before each batch.
I suspect this supersedes our current workaround, but for safety keep
doing both.
v2: The magic number shall be 2.
This doesn't conclusively prove that it is the mythical TLB bug we've
been trying to workaround for so long, that it requires touching a number
of pages to prevent the corruption indicates to me that it is TLB
related, but the corruption (the reversed cacheline) is more subtle than
a TLB bug, where we would expect it to read the wrong page entirely.
Oh well, it prevents a reliable hang for me and so probably for others
as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville found an old w/a documented for g4x that suggested that we need to
reset the HEAD after writing START. This is a useful fixup for some of
the g4x ring initialisation woes, but as usual, not all.
v2: Do the rewrite unconditionally anyway
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we happen to emit more than I915_MAX_WA_REGS workarounds, we will
currently discard them, not even emit the LRI. Not really what we want,
so warn loudly.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When entering intel_ring_emit_wa() with num_wa_regs equal to
I915_MAX_WA_REGS, we end up indexing the intel_wa_regs array beyond its
allocation.
Fix the check then.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the BDW example and apply the workarounds touching registers
which are saved in the context image through LRIs in the new
ring->init_context() hook.
This makes Mesa much happier and eg. glxgears doesn't hang after
the first frame.
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add missing wa table initialization to avoid a functional
conflict with Arun's wa table debugfs support.]
Reviewed-by: "Barbalho, Rafael" <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The workarounds that are applied are exported to a debugfs file;
this is used to verify their state after the test case (reset or
suspend/resume etc). This patch is only required to support i-g-t.
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For BDW workarounds are currently initialized in init_clock_gating() but
they are lost during reset, suspend/resume etc; this patch moves the WAs
that are part of register state context to render ring init fn otherwise
default context ends up with incorrect values as they don't get initialized
until init_clock_gating fn.
v2: Add workarounds to golden render state
This method has its own issues, first of all this is different for
each gen and it is generated using a tool so adding new workaround
and mainitaining them across gens is not a straightforward process.
v3: Use LRIs to emit these workarounds (Ville)
Instead of modifying the golden render state the same LRIs are
emitted from within the driver.
v4: Use abstract name when exporting gen specific routines (Chris)
For: VIZ-4092
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to spec FBC on BDW and HSW are identical without any gaps.
So let's copy the nuke and let FBC really start compressing stuff.
Without this patch we can verify with false color that nothing is being
compressed. With the nuke in place and false color it is possible
to see false color debugs.
Unfortunatelly on some rings like BCS on BDW we have to avoid Bits 22:18 on
LRIs due to a high risk of hung. So, when using Blt ring for frontbuffer rend
cache would never been cleaned and FBC would stop compressing buffer.
One alternative is to cache clean on software frontbuffer tracking.
v2: Fix rebase conflict.
v3: Do not clean cache on BCS ring. Instead use sw frontbuffer tracking.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we reset a ring after a hang, we have to make sure that we clear
out all queued Execlists requests.
v2: The ring is, at this point, already being correctly re-programmed
for Execlists, and the hangcheck counters cleared.
v3: Daniel suggests to drop the "if (execlists)" because the Execlists
queue should be empty in legacy mode (which is true, if we do the
INIT_LIST_HEAD).
v4: Do the pending intel_runtime_pm_put
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A subsequent patch will no longer initialize the aliasing ppgtt if we
have full ppgtt enabled, since we simply don't need that any more.
Unfortunately a few places check for the aliasing ppgtt instead of
checking for ppgtt in general. Fix them up.
One special case are the gtt offset and size macros, which have some
code to remap the aliasing ppgtt to the global gtt. The aliasing ppgtt
is _not_ a logical address space, so passing that in as the vm is
plain and simple a bug. So just WARN about it and carry on - we have a
gracefully fall-through anyway if we can't find the vma.
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as the legacy-style ring->flush.
v2: The BSD invalidate bit still exists in GEN8! Add it for the VCS
rings (but still consolidate the blt and bsd ring flushes into one).
This was noticed by Brad Volkin.
v3: The command for BSD and for other rings is slightly different:
get it exactly the same as in gen6_ring_flush + gen6_bsd_ring_flush
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Well, new-ish: if all this code looks familiar, that's because it's
a clone of the existing submission mechanism (with some modifications
here and there to adapt it to LRCs and Execlists).
And why did we do this instead of reusing code, one might wonder?
Well, there are some fears that the differences are big enough that
they will end up breaking all platforms.
Also, Execlists offer several advantages, like control over when the
GPU is done with a given workload, that can help simplify the
submission mechanism, no doubt. I am interested in getting Execlists
to work first and foremost, but in the future this parallel submission
mechanism will help us to fine tune the mechanism without affecting
old gens.
v2: Pass the ringbuffer only (whenever possible).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch. Again. And drop the legacy sarea gunk
that somehow crept in.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Logical rings do not need most of the initialization their
legacy ringbuffer counterparts do: we just need the pipe
control object for the render ring, enable Execlists on the
hardware and a few workarounds.
v2: Squash with: "drm/i915: Extract pipe control fini & make
init outside accesible".
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Make checkpatch happy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allocate and populate the default LRC for every ring, call
gen-specific init/cleanup, init/fini the command parser and
set the status page (now inside the LRC object). These are
things all engines/rings have in common.
Stopping the ring before cleanup and initializing the seqnos
is left as a TODO task (we need more infrastructure in place
before we can achieve this).
v2: Check the ringbuffer backing obj for ring_is_initialized,
instead of the context backing obj (similar, but not exactly
the same).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Any given ringbuffer is unequivocally tied to one context and one engine.
By setting the appropriate pointers to them, the ringbuffer struct holds
all the infromation you might need to submit a workload for processing,
Execlists style.
v2: Drop ring->ctx since that looks terribly ill-defined for legacy
ringbuffer submission.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com> (v1)
Acked-by: Damien Lespiau <damien.lespiau@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we have said a couple of times by now, logical ring contexts have
their own ringbuffers: not only the backing pages, but the whole
management struct.
In a previous version of the series, this was achieved with two separate
patches:
drm/i915/bdw: Allocate ringbuffer backing objects for default global LRC
drm/i915/bdw: Allocate ringbuffer for user-created LRCs
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During ring initialisation, sometimes we observe, though not in
production hardware, that the idle flag is not set even though the ring
is empty. Double check before giving up.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Doing a 1s wait (tops) with the cpu is a bit excessive. Tune it down
like everything else in that code.
v2: Also insert the missing space Chris spotted.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Withtout this, ring initialization fails reliabily during resume with
[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head ffffff8804 tail 00000000 start 000e4000
This is not a complete fix, but it is verified to make the ring
initialization failures during resume much less likely.
We were not able to root-cause this bug (likely HW-specific to Gen4 chips)
yet. This is therefore used as a ducttape before problem is fully
understood and proper fix created, so that people don't suffer from
completely unusable systems in the meantime.
The discussion and debugging is happening at
https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Broadwell, any PIPE_CONTROL with the "State Cache Invalidate" bit set
must be preceded by a PIPE_CONTROL with the "CS Stall" bit set.
Documented on the BSpec 3D workarounds page.
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[vsyrjala: add chv w/a note too]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll want to reuse this for a workaround.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rmove now unused int.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Traditionally we use genX_ for GT/render stuff and the codenames for
display stuff. But the gt and pm interrupt handling functions on
gen5/6+ stuck out as exceptions, so convert them.
Looking at the diff this nicely realigns our ducks since almost all
the callers are already platform-specific functions following the
genX_ pattern.
Spotted while reviewing some internal rps patches.
No function change in this patch.
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On g33, the documentation states
"HWS_PGA:
Format = Bits 28:12 of graphics memory address (bits 31:29 MBZ)."
which translates to that the address of the HWS must be below 256MiB,
which is conveniently the mappable aperture.
This also appears to be true (but not documented as so) for gen4 and
gen5. To generalise we force it into the low mappable region for all
non-LLC platforms. If we locate the HWS at the top of the GTT the
machine will hard hang during boot (fails on pnv, gm45, ilk and byt,
but works on snb, ivb, hsw).
v2: Add comments to explain why use PIN_MAPPABLE even though we have
no intention of mapping the object. (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's simple enough that it doesn't need to know anything about the
engine.
Trivial change.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More prep work: with Execlists, we are going to start creating a lot
of extra ringbuffers soon, so these functions are handy.
No functional changes.
v2: rename allocate/destroy_ring_buffer to alloc/destroy_ringbuffer_obj
because the name is more meaningful and to mirror a similar function in
the context world: i915_gem_alloc_context_obj(). Change suggested by Brad
Volkin.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Ville points out, it's possible/probable we don't actually need this.
Potentially, this validates the letter of the spec, and not the spirit.
Ville:
> I discussed this on irc w/ Ben, and I was suggesting we don't need to
> poll. Polling apparently can be used as a workaround for certain
> hardware issues, but it looks like those issues shouldn't affect us,
> for the momemnt at least. So my suggestion was to try w/o polling
> first (since there could be some power cost to polling) and add the
> poll bit if problems arise.
Rodrigo: Spec suggests this as an W/A for GT3. However semaphores didn't
worked in my BDW GT2 on Signal Mode. So pool mode is definitely needed.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore waits use a new instruction, MI_SEMAPHORE_WAIT. The seqno to
wait on is all well defined by the table in the previous patch. There is
nothing else different from previous GEN's semaphore synchronization
code.
v2: Update macros to not require the other ring's ring->id (Chris)
v3: Add missing VCS2 gen8_ring_wait init besides
s/ring_buffer/engine_cs (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore signalling works similarly to previous GENs with the exception
that the per ring mailboxes no longer exist. Instead you must define
your own space, somewhere in the GTT.
The comments in the code define the layout I've opted for, which should
be fairly future proof. Ie. I tried to define offsets in abstract terms
(NUM_RINGS, seqno size, etc).
NOTE: If one wanted to move this to the HWSP they could. I've decided
one 4k object would be easier to deal with, and provide potential wins
with cache locality, but that's all speculative.
v2: Update the macro to not need the other ring's ring->id (Chris)
Update the comment to use the correct formula (Chris)
v3: Move the macros the ringbuffer.h to prevent churn in next patch
(Ville)
v4: Fixed compilation rebase conflict
commit 1ec9e26dda
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Feb 14 14:01:11 2014 +0100
drm/i915: Consolidate binding parameters into flags
v5: VCS2 rebase
Replace hweight_long with hweight32
v6 (Rodrigo): * Add missed VC2 gen8 ring signal init
* fixing conflicst on rebase
* minor fixes on address table
* remove WARN_ON
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the ring mask we now have an easy way to know the number of rings
in the system, and therefore can accurately predict the number of dwords
to emit for semaphore signalling. This was not possible (easily)
previously.
There should be no functional impact, simply fewer instructions emitted.
While we're here, simply do the round up to 2 instead of the fancier
rounding we did before, which rounding up per mbox, ie 4. This also
allows us to drop the unnecessary MI_NOOP, so not really 4, 3.
v2: Use 3 dwords instead of 4 (Ville)
Do the proper calculation to get the number of dwords to emit (Ville)
Conditionally set .sync_to when semaphores are enabled (Ville)
v3: Rebased on VCS2
Replace hweight_long with hweight32 (Ville)
v4: Pull out the accidentally squashed hunk from the next patch after
rebase (Daniel).
v5: Fix conflict after rebase (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen8 has already had some differentiation with how it handles rings.
Semaphores bring yet more differences, and now is as good a time as any
to do the split.
Also, since gen8 doesn't actually use semaphores up until this point,
put the proper "NULL" values in for the mbox info.
v2: v1 had a stale commit message
v3: Move everything in the is_semaphore_enabled() check
v4: VCS2 rebase
Remove double assignment of signal in render ring (Ville)
v5: Adding missed VCS2 signal init on gen8+ (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It just fix a typo.
v2: removing underscore to let this like all other ring names (Oscar)
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by (v1): Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit add check for return value of init_ring_common() in the
init_render_ring(). Now, when failure is detected the error code is
propagated to the caller instead of being ignored.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds support for a write-enable bit in the entry of GTT.
This is handled via a read-only flag in the GEM buffer object which
is then used to see how to set the bit when writing the GTT entries.
Currently by default the Batch buffer & Ring buffers are marked as read only.
v2: Moved the pte override code for read-only bit to 'byt_pte_encode'. (Chris)
Fixed the issue of leaving 'gt_old_ro' as unused. (Chris)
v3: Removed the 'gt_old_ro' field, now setting RO bit only for Ring Buffers(Daniel).
v4: Added a new 'flags' parameter to all the pte(gen6) encode & insert_entries functions,
in lieu of overloading the cache_level enum (Daniel).
v5: Removed the superfluous VLV check & changed the definition location of PTE_READ_ONLY flag (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These do not exist anymore.
Spotted while reading through intel_ringbuffer.c
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen2 doesn't have the ring idle/stop bits in the SCPD/MI_MODE register,
so don't go spewing warnings about the state of those bits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Manual cleanup after the previous Coccinelle script.
Yes, I could write another Coccinelle script to do this but I
don't want labor-replacing robots making an honest programmer's
work obsolete (also, I'm lazy).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As advanced by the previous patch, the ringbuffers and the engine
command streamers belong in different structs. This is so because,
while they used to be tightly coupled together, the new Logical
Ring Contexts (LRC for short) have a ringbuffer each.
In legacy code, we will use the buffer* pointer inside each ring
to get to the pertaining ringbuffer (the actual switch will be
done in the next patch). In the new Execlists code, this pointer
will be NULL and we will use instead the one inside the context
instead.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We implement the following workarounds:
* WaDisableAsyncFlipPerfMode:chv
* WaProgramMiArbOnOffAroundMiSetContext:chv
v2: Drop WaDisableSemaphoreAndSyncFlipWait note
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we dont have semaphores enabled, we allocate 4
dwords for signalling. But end up emitting more regardless.
Fix this by bailing out early if semaphores are not enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78274
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78283
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is missing in:
commit 78325f2d27
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Tue Apr 29 14:52:29 2014 -0700
drm/i915: Virtualize the ringbuffer signal func
Looks to me like a rebase side-effect...
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For clients that submit large batch buffers the command parser has
a substantial impact on performance. On my HSW ULT system performance
drops as much as ~20% on some tests. Most of the time is spent in the
command lookup code. Converting that from the current naive search to
a hash table lookup reduces the performance drop to ~10%.
The choice of value for I915_CMD_HASH_ORDER allows all commands
currently used in the parser tables to hash to their own bucket (except
for one collision on the render ring). The tradeoff is that it wastes
memory. Because the opcodes for the commands in the tables are not
particularly well distributed, reducing the order still leaves many
buckets empty. The increased collisions don't seem to have a huge
impact on the performance gain, but for now anyhow, the parser trades
memory for performance.
NB: Ville noticed that the error paths through the ring init code
will leak memory. I've not addressed that here. We can do a follow
up pass to handle all of the leaks.
v2: improved comment describing selection of hash key mask (Damien)
replace a BUG_ON() with an error return (Tvrtko, Ville)
commit message improvements
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the review of
commit 1f70999f90
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Jan 27 22:43:07 2014 +0000
drm/i915: Prevent recursion by retiring requests when the ring is full
Ville raised the point that our interaction with request->tail was
likely to foul up other uses elsewhere (such as hang check comparing
ACTHD against requests).
However, we also need to restore the implicit retire requests that certain
test cases depend upon (e.g. igt/gem_exec_lut_handle), this raises the
spectre that the ppgtt will randomly call i915_gpu_idle() and recurse
back into intel_ring_begin().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78023
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Remove now unused 'tail' variable as spotted by Brad.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few improvements to the fallback method for waiting upon ring space:
1. Fix the start/end wait tracepoints to always be paired.
2. Increase responsiveness of checking
3. Mark the process as waiting upon io
4. Check for signal interruptions
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Drop the s/msleep/io_schedule_timeout/ change again since the
latter isn't exported.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, our code only had a 32b offset value for where the
batchbuffer starts. With full PPGTT, and 64b canonical GPU address
space, that is an insufficient value. The code to expand is pretty
straight forward, and only one platform needs to do anything with the
extra bits.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add_request has always contained both the semaphore mailbox updates as
well as the breadcrumb writes. Since the semaphore signal is the one
which actually knows about the number of dwords it needs to emit to the
ring, we move the ring_begin to that function. This allows us to remove
the hideously shared #define
On a related not, gen8 will use a different number of dwords for
semaphores, but not for add request.
v2: Make number of dwords an explicit part of signalling (via function
argument). (Chris)
v3: very slight comment change
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This abstraction again is in preparation for gen8. Gen8 will bring new
semantics for doing this operation.
While here, make the writes of MI_NOOPs explicit for non-existent rings.
This should have been implicit before.
NOTE: This is going to be removed in a few patches.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be helpful in abstracting some of the code in preparation for
gen8 semaphores.
v2: Move mbox stuff to a separate struct
v3: Rebased over VCS2 work
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Gen7 doesn't have the second BSD ring. But it will complain the switch check
warning message during compilation. So just add it to remove the
switch check warning.
V1->V2: Follow Daniel's comment to update the comment
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we include the expected values for the failing ring register checks,
it makes it marginally easier to see which is the culprit.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tearing down the ring buffers across resume is overkill, risks
unnecessary failure and increases fragmentation.
After failure, since the device is still active we may end up trying to
write into the dangling iomapping and trigger an oops.
v2: stop_ringbuffers() was meant to call stop(ring) not
cleanup(ring) during resume!
Reported-by: Jae-hyeon Park <jhyeon@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72351
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: s/ring->obj == NULL/!intel_ring_initialized(ring)/ as
suggested by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For readibility and guess at the meaning behind the constants.
v2: Claim only the meagerest connections with reality.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Piglit runner and QA are both looking at the dmesg for
DRM_ERRORs with test cases. Add a flag to control those
when we they are expected from related test cases.
Also add flag to control if contexts should be banned
that introduced the hang. Hangcheck is timer based and
preventing bans by adding sleeps to testcases makes
testing slower.
v2: intel_ring_stopped(), readable comment (Chris)
v3: keep compatibility (Daniel)
References: https://bugs.freedesktop.org/show_bug.cgi?id=75876
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have been setting the bit which was originally BIOS dependent since:
commit f05bb0c7b6
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jan 20 16:33:32 2013 +0000
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
Therefore, we do not need to try to figure it out dynamically and we can
just always invalidate the TLBs.
It's a partial revert of:
commit 12b0286f49
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Jun 4 14:42:50 2012 -0700
drm/i915: possibly invalidate TLB before context switch
The original commit attempted to only invalidate when necessary
(very much a relic from the old days). Now, we can just always invalidate.
I guess the old TODO still exists. Since we seem to have abandoned ILK
contexts however, there isn't much point in even remembering.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch Enables the bit for TLB invalidate in GFX Mode register
for Gen7.
According to bspec, When enabled this bit limits the invalidation
of the TLB only to batch buffer boundaries, to pipe_control
commands which have the TLB invalidation bit set and sync flushes.
If disabled, the TLB caches are flushed for every full flush of
the pipeline.
Tested only on vlv platform. Chris has tested on ivb and hsw
platforms.
v2: Adding the explicit enabling of this bit for all Gen7 platforms
instead of only vlv (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> #ivb, hsw -Chris
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add w/a markers as suggested by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The documentation calls this GFX_MODE bit "Flush TLB invalidate Mode".
However, that is not a good name for an enable bit as it doesn't make it
clear what is enabled. An even worse name is GFX_TLB_INVALIDATE_ALWAYS
as enabling that bit actually prevents the TLB from being invalidated at
every flush. This leads to great confusion when reading code and
proposed patches. To get around this try to bake in what is enabled by
setting the bit and call it GFX_TLB_INVALIDATE_EXPLICIT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Gupta, Sourab" <sourab.gupta@intel.com>
Acked-by: "Gupta, Sourab" <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Broadwell has an increased virtual address size, it requires more
than 32 bits to store offsets into its address space. This includes the
debug registers to track the current HEAD of the individual rings, which
may be anywhere within the per-process address spaces. In order to find
the full location, we need to read the high bits from a second register.
We then also need to expand our storage to keep track of the larger
address.
v2: Carefully read the two registers to catch wraparound between
the reads.
v3: Use a WARN_ON rather than loop indefinitely on an unstable
register read.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk which conflicted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch Removes the VS_TIMER_DISPATCH bit enable in MI MODE reg for
platforms > Gen6.
VS_TIMER_DISPATCH bit enable was earlier required as a part of
WA 'WaTimedSingleVertexDispatch', which is now applicable only to
platforms < Gen7.
v2: Enhancing the scope of the patch to full Gen7 (Chris)
v3: Modifying the WA condition to the cover the applicable platforms,
and adding the WA name in comments. (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # ivb, hsw -Chris
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While wandering in the spec, I noticed that BDW removes those 2 bits
from INSTPM. I couldn't find any direct way to invalidate the TLB (ie
without the ring working already). Maybe someone will be more lucky.
At least, we now know we may be a problem.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on Bspec the command parser must be stopped prior to
issuing sync flush. This should be done by the caller of
intel_ring_setup_status_page. Patch adds a warning if it is
not done.
v2: rebased based on new patch (wait for ring to become idle)
Signed-off-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
make sure we wait for rings to become idle once they are
disabled. In case of timeout print an error message
Signed-off-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
[danvet: Frob patch as suggested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rings should be idle before issuing sync_flush
(in intel_ring_setup_status_page). This patch moves the ring
disabling before doing the HW status page setup.
Signed-off-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command parser scans batch buffers submitted via execbuffer ioctls before
the driver submits them to hardware. At a high level, it looks for several
things:
1) Commands which are explicitly defined as privileged or which should only be
used by the kernel driver. The parser generally rejects such commands, with
the provision that it may allow some from the drm master process.
2) Commands which access registers. To support correct/enhanced userspace
functionality, particularly certain OpenGL extensions, the parser provides a
whitelist of registers which userspace may safely access (for both normal and
drm master processes).
3) Commands which access privileged memory (i.e. GGTT, HWS page, etc). The
parser always rejects such commands.
See the overview comment in the source for more details.
This patch only implements the logic. Subsequent patches will build the tables
that drive the parser.
v2: Don't set the secure bit if the parser succeeds
Fail harder during init
Makefile cleanup
Kerneldoc cleanup
Clarify module param description
Convert ints to bools in a few places
Move client/subclient defs to i915_reg.h
Remove the bits_count field
OTC-Tracker: AXIA-4631
Change-Id: I50b98c71c6655893291c78a2d1b8954577b37a30
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split out from Chris vma-bind rework.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We access it through the cpu window. No functional difference expected
atm since we default to a bottom-up allocation scheme. But that might
eventually change so that we prefer the unmappable range for buffers
that don't need cpu gtt access.
Split out from Chris vma-bind rework.
Note that this is only possible due to the split-up of the mappable
pin flag into PIN_GLOBAL and PIN_MAPPABLE.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tighter code since legacy gem has only mappable anyway.
Split out from Chris vma-bind rework.
Note that this is only possible due to the split-up of the mappable
pin flag into PIN_GLOBAL and PIN_MAPPABLE.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split out from Chris vma-bind rework.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Anything more than just one bool parameter is just a pain to read,
symbolic constants are much better.
Split out from Chris' vma-binding rework patch.
v2: Undo the behaviour change in object_pin that Chris spotted.
v3: Split out misplaced hunk to handle set_cache_level errors,
spotted by Jani.
v4: Keep the current over-zealous binding logic in the execbuffer code
working with a quick hack while the overall binding code gets shuffled
around.
v5: Reorder the PIN_ flags for more natural patch splitup.
v6: Pull out the PIN_GLOBAL split-up again.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_ring_cachline_align() emits MI_NOOPs until the ring tail is
aligned to a cacheline boundary.
Cc: Bjoern C <lkml@call-home.ch>
Cc: Alexandru DAMIAN <alexandru.damian@intel.com>
Cc: Enrico Tagliavini <enrico.tagliavini@gmail.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org (prereq for the next patch)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the VM do not track activity of objects and instead use a large
hammer to forcibly idle and evict all of their associated objects when
one is released, it is possible for that to cause a recursion when we
need to wait for free space on a ring and call retire requests.
(intel_ring_begin -> intel_ring_wait_request ->
i915_gem_retire_requests_ring -> i915_gem_context_free ->
i915_gem_evict_vm -> i915_gpu_idle -> intel_ring_begin etc)
In order to remove the requirement for calling retire-requests from
intel_ring_wait_request, we have to inline a couple of steps from
retiring requests, notably we have to record the position of the request
we wait for and use that to update the available ring space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because whatever.*
* This should contain a fairly long list of issues and still
unresolved resgressions, but I didn't really get a vote.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ring will emit too many if semaphores are disabled since we do not
add the correct number to num_dwords anymore.
This was introduced:
commit 52ed23253b
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Mon Dec 16 20:50:38 2013 -0800
drm/i915: Don't emit mbox updates without semaphores
FWIW, the bug was fixed later in the series.
/me hangs head in shame.
Daniel: Also note that we should have merged the read-only semaphore
modparam before this patch.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In very rare cases (such as a memory failure stress test) it is possible
to fill the entire ring without emitting a request. Under this
circumstance, the outstanding request is flushed and waited upon. After
space on the ring is cleared, we return to emitting the new command -
except that we just cleared the seqno allocated for this operation and
trigger the sanity check that a request is only ever emitted with a
valid seqno. The fix is to rearrange the code to make sure the
allocation of the seqno for this operation is after any required flushes
of outstanding operations.
The bug exists since the preallocation was introduced in
commit 9d7730914f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Nov 27 16:22:52 2012 +0000
drm/i915: Preallocate next seqno before touching the ring
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Aside from the fact that it leaves confusing dumps on error capture, it
is entirely unnecessary, and potentially harmful in cases like BDW,
where the instruction has changed.
In reality (seemingly), this will have no behavioral impact.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added power well arguments to all the force wake routines
to help us individually control power well based on the
scenario.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the removed forcewake hack and drop one
spurious hunk Jesse noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I believe, and an evening of i-g-t, that our original workaround for the
missed interrupts on Sandybridge, that of holding forcewake whilst we
wait for an interrupts, is no longer required. This leaves us dependent
on the second workaround of forcing an UC read of the ACTHD before
reading back the seqno from the snooped HWS. Dropping the forcewake
should allow us to conserve a little power, not much as the GPU is meant
to be busy whilst we wait for it!
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec tells us that we need to emit an SRM after the LRI
to MSG_FBC_REND_STATE.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't issue the FBC nuke/cache clean command when invalidate_domains!=0.
That would indicate that we're not being called for the post-batch
flush.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This confused me some many times that I think it is appropriate to add a
small comment to instruct the reader of the code that it is indeed doing
what it is supposed to do.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The handling of the error interrupts isn't wired up at all. And it
hasn't been ever since ilk happened, so don't bother.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was an oversight and should have been in a previous series
somewhere.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPE_CONTROL added the high address dword. I'm not sure how the
simulator let me get away with this. I've explicitly left out all the
workarounds from Gen7 because in the minimal digging that I did, most
don't seem necessary, and the simulator doesn't complain without them
Note that BLT and BSD ring commands had already been updated previously.
Just render/pipe_control should have been broken.
v2: Squash in a fixup from Ville to follow the recent IVB PIPE_CONTROL
updates: "BDW uses the IVB PIPE_CONTROL style for specifying GTT vs.
PPGTT for the PIPE_CONTROL QW/DW write."
v3: Rebase on top of Chris' cleanup to have an explicit ring->scratch
buffer object instead of an opaque ring->private where everyone stores
the same stuff inside.
Reported-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (for the fixup)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in fix from Ben: Set PPGTT batches as necessary
This fixes the regression in the last couple of days when we enabled
PPGTT.
v3: Squash in fixup to still use GTT for secure batches from Ville:
BDW doesn't have a separate secure vs. non-secure bit in
MI_BATCH_BUFFER_START. So for secure batches we have to simply
leave the PPGTT bit unset. Fortunately older generations (except
HSW) had similar limitations so execbuffer already creates a GTT
mapping for all secure batches.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code is more verbose than necessary for the reader's sake, hopefully
the compiler optimizes away the if.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command to emit batch buffers has changed to address 48b addresses.
It seemed reasonable that we could still use the old instruction where
emitting 0 for length would do the right thing, but it seems to bother
the simulator when the code does that.
Now the second dword in the command has the upper 16b of the address of
the batchbuffer.
v2: Remove duplicated vfun assignment.
v3: Squash in VECS support changes from Zhao Yakui <yakui.zhao@intel.com>
v4: Make checkpatch happy.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interrupt handling implementation remains the same as previous
generations with the 4 types of registers, status, identity, mask, and
enable. However the layout of where the bits go have changed entirely.
To address these changes, all of the interrupt vfuncs needed special
gen8 code.
The way it works is there is a top level status register now which
informs the interrupt service routine which unit caused the interrupt,
and therefore which interrupt registers to read to process the
interrupt. For display the division is quite logical, a set of interrupt
registers for each pipe, and in addition to those, a set each for "misc"
and port.
For GT the things get a bit hairy, as seen by the code. Each of the GT
units has it's own bits defined. They all look *very similar* and
resides in 16 bits of a GT register. As an example, RCS and BCS share
register 0. To compact the code a bit, at a slight expense to
complexity, this is exactly how the code works as well. 2 structures are
added to the ring buffer so that our ring buffer interrupt handling code
knows which ring shares the interrupt registers, and a shift value (ie.
the top or bottom 16 bits of the register).
The above allows us to kept the interrupt register caching scheme, the
per interrupt enables, and the code to mask and unmask interrupts
relatively clean (again at the cost of some more complexity).
Most of the GT units mentioned above are command streamers, and so the
symmetry should work quite well for even the yet to be implemented rings
which Broadwell adds.
v2: Fixes up a couple of bugs, and is more verbose about errors in the
Broadwell interrupt handler.
v3: fix DE_MISC IER offset
v4: Simplify interrupts:
I totally misread the docs the first time I implemented interrupts, and
so this should greatly simplify the mess. Unlike GEN6, we never touch
the regular mask registers in irq_get/put.
v5: Rebased on to of recent pch hotplug setup changes.
v6: Fixup on top of moving num_pipes to intel_info.
v7: Rebased on top of Egbert Eich's hpd irq handling rework. Also
wired up ibx_hpd_irq_setup for gen8.
v8: Rebase on top of Jani's asle handling rework.
v9: Rebase on top of Ben's VECS enabling for Haswell, where he
unfortunately went OCD on the gt irq #defines. Not that they're still
not yet fully consistent:
- Used the GT_RENDER_ #defines + bdw shifts.
- Dropped the shift from the L3_PARITY stuff, seemed clearer.
- s/irq_refcount/irq_refcount.gt/
v10: Squash in VECS enabling patches and the gen8_gt_irq_handler
refactoring from Zhao Yakui <yakui.zhao@intel.com>
v11: Rebase on top of the interrupt cleanups in upstream.
v12: Rebase on top of Ben's DPF changes in upstream.
v13: Drop bdw from the HAS_L3_DPF feature flag for now, it's unclear what
exactly needs to be done. Requested by Ben.
v14: Fix the patch.
- Drop the mask of reserved bits and assorted logic, it doesn't match
the spec.
- Do the posting read inconditionally instead of commenting it out.
- Add a GEN8_MASTER_IRQ_CONTROL definition and use it.
- Fix up the GEN8_PIPE interrupt defines and give the GEN8_ prefixes -
we actually will need to use them.
- Enclose macros in do {} while (0) (checkpatch).
- Clear DE_MISC interrupt bits only after having processed them.
- Fix whitespace fail (checkpatch).
- Fix overtly long lines where appropriate (checkpatch).
- Don't use typedef'ed private_t (maintainer-scripts).
- Align the function parameter list correctly.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bikeshed
I had this lying around from he original PPGTT series, and thought we
might try to get it in by itself.
It's convenient to just call i915_gem_init_hw at reset because we'll be
adding new things to that function, and having just one function to call
instead of reimplementing it in two places is nice.
In order to accommodate we cleanup ringbuffers in order to bring them
back up cleanly. Optionally, we could also teardown/re initialize the
default context but this was causing some problems on reset which I
wasn't able to fully debug, and is unnecessary with the previous context
init/enable split.
This essentially reverts:
commit 8e88a2bd59
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 19 18:40:00 2012 +0200
drm/i915: don't call modeset_init_hw in i915_reset
It seems to work for me on ILK now. Perhaps it's due to:
commit 8a5c2ae753
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Mar 28 13:57:19 2013 -0700
drm/i915: fix ILK GPU reset for render
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that MMIO has been split up into gen specific functions it is
obvious when HAS_FPGA_DBG_UNCLAIMED, HAS_FORCE_WAKE are needed. As such,
we can remove this extraneous condition.
As a result of this, as well as previously existing function pointers
for forcewake, we no longer need the has_force_wake member in the device
specific data structure.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'd only ever used this define to denote whether or not we have the
dynamic parity feature (DPF) and never to determine whether or not L3
exists. Baytrail is a good example of where L3 exists, and not DPF.
This patch provides clarify in the code for future use cases which might
want to actually query whether or not L3 exists.
v2: Add /* DPF == dynamic parity feature */
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Certain HSW SKUs have a second bank of L3. This L3 remapping has a
separate register set, and interrupt from the first "slice". A slice is
simply a term to define some subset of the GPU's l3 cache. This patch
implements both the interrupt handler, and ability to communicate with
userspace about this second slice.
v2: Remove redundant check about non-existent slice.
Change warning about interrupts of unknown slices to WARN_ON_ONCE
Handle the case where we get 2 slice interrupts concurrently, and switch
the tracking of interrupts to be non-destructive (all Ville)
Don't enable/mask the second slice parity interrupt for ivb/vlv (even
though all docs I can find claim it's rsvd) (Ville + Bryan)
Keep BYT excluded from L3 parity
v3: Fix the slice = ffs to be decremented by one (found by Ville). When
I initially did my testing on the series, I was using 1-based slice
counting, so this code was correct. Not sure why my simpler tests that
I've been running since then didn't pick it up sooner.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ignoring the legacy DRI1 code, and a couple of special cases (to be
discussed later), all access to the ring is mediated through requests.
The first write to a ring will grab a seqno and mark the ring as having
an outstanding_lazy_request. Either through explicitly adding a request
after an execbuffer or through an implicit wait (either by the CPU or by
a semaphore), that sequence of writes will be terminated with a request.
So we can ellide all the intervening writes to the tail register and
send the entire command stream to the GPU at once. This will reduce the
number of *serialising* writes to the tail register by a factor or 3-5
times (depending upon architecture and number of workarounds, context
switches, etc involved). This becomes even more noticeable when the
register write is overloaded with a number of debugging tools. The
astute reader will wonder if it is then possible to overflow the ring
with a single command. It is not. When we start a command sequence to
the ring, we check for available space and issue a wait in case we have
not. The ring wait will in this case be forced to flush the outstanding
register write and then poll the ACTHD for sufficient space to continue.
The exception to the rule where everything is inside a request are a few
initialisation cases where we may want to write GPU commands via the CS
before userspace wakes up and page flips.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible for us to be forced to perform an allocation for the lazy
request whilst running the shrinker. This allocation may fail, leaving
us unable to reclaim any memory leading to premature OOM. A neat
solution to the problem is to preallocate the request at the same time
as acquiring the seqno for the ring transaction. This means that we can
report ENOMEM prior to touching the rings.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prior to preallocating an request for lazy emission, rename the existing
field to make way (and differentiate the seqno from the request struct).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now have more devices using ring->private than not, and they all want
the same structure. Worse, I would like to use a scratch page from
outside of intel_ringbuffer.c and so for convenience would like to reuse
ring->private. Embed the object into the struct intel_ringbuffer so that
we can keep the code clean.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Just like we're doing with the other IMR changes.
One of the functional changes is that not every caller was doing the
POSTING_READ.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like the functions that touch DEIMR and SDEIMR, but for GTIMR.
The new functions contain a POSTING_READ(GTIMR) which was not present
at the 2 callers inside i915_irq.c.
The implementation is based on ibx_display_interrupt_update.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We require n-1 mailboxes for proper semaphore synchronization. All
semaphore synchronization code relies on proper values in these
mailboxes. The fact that we failed to touch the vebox ring by itself
was unlikely to be an issue since the HW should be initializing the
values to 0. However the error framework for testing seqno wrap
introduced by Mika, in addition to the hangcheck via seqno, and
i915_error_first_batchbuffer() combined caused a nice explosion.
The problem is caused by seqno wrap because the wrap condition is not
properly setup. The wrap code attempts to set the sync mailboxes all
to 0, and then set the current seqno to one less than 0. In all cases,
the vebox mailbox wasn't properly being initialized. This caused a
wrap to not occur. When hangcheck kicks in with the bogus seqno
values, the rest just doesn't work. It makes me wonder if we shouldn't
consider a dumber version of hangcheck...
How we messed this up: VECS support was written before the
aforementioned other features. Upon VECS being rebased, these facts
were missed.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65387
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67198
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After any "soft gfx reset" we must manually invalidate the TLBs
associated with each ring. Empirically, it seems that a
suspend/resume or D3-D0 cycle count as a "soft reset". The symptom is
that the hardware would fail to note the new address for its status
page, and so it would continue to write the shadow registers and
breadcrumbs into the old physical address (now used by something
completely different, scary). Whereas the driver would read the new
status page and never see any progress, it would appear that the GPU
hung immediately upon resume.
Based on a patch by naresh kumar kachhi <naresh.kumar.kacchi@intel.com>
Reported-by: Thiago Macieira <thiago@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thiago Macieira <thiago@kde.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To verbalize it, one can say, "pin an object into the given address
space." The semantics of pinning remain the same otherwise.
Certain objects will always have to be bound into the global GTT.
Therefore, global GTT is a special case, and keep a special interface
around for it (i915_gem_obj_ggtt_pin).
v2: s/i915_gem_ggtt_pin/i915_gem_obj_ggtt_pin
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218
Merge: 42577ca058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code to handle it is broken - there's simply no code to clear CS
parser errors on gen5+. And behold, for all the other rings we also
don't enable it!
Leave the handling code itself in place just to be consistent with the
existing mess though. And in case someone feels like fixing it all up.
This has been errornously enabled in
commit 12638c57f3
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:31 2013 -0700
drm/i915: Enable vebox interrupts
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the simplified locking there's no reason any more to keep the
refcounts seperate.
v2: Readd the lost comment that ring->irq_refcount is protected by
dev_priv->irq_lock.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the rps interrupt locking isn't clearly separated (at elast
conceptually) from all the other interrupt locking having a different
lock stopped making sense: It protects much more than just the rps
workqueue it started out with. But with the addition of VECS the
separation started to blurr and resulted in some more complex locking
for the ring interrupt refcount.
With this we can (again) unifiy the ringbuffer irq refcounts without
causing a massive confusion, but that's for the next patch.
v2: Explain better why the rps.lock once made sense and why no longer,
requested by Ben.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not a good idea to also run the pipe_control cleanup.
This regression has been introduced whith the original cs tlb w/a in
commit b45305fce5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Dec 17 16:21:27 2012 +0100
drm/i915: Implement workaround for broken CS tlb on i830/845
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64610
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Soon we want to gut a lot of our existing assumptions how many address
spaces an object can live in, and in doing so, embed the drm_mm_node in
the object (and later the VMA).
It's possible in the future we'll want to add more getter/setter
methods, but for now this is enough to enable the VMAs.
v2: Reworked commit message (Ben)
Added comments to the main functions (Ben)
sed -i "s/i915_gem_obj_set_color/i915_gem_obj_ggtt_set_color/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_bound/i915_gem_obj_ggtt_bound/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_size/i915_gem_obj_ggtt_size/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_offset/i915_gem_obj_ggtt_offset/" drivers/gpu/drm/i915/*.[ch]
(Daniel)
v3: Rebased on new reserve_node patch
Changed DRM_DEBUG_KMS to actually work (will need fixing later)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes gpu reset on my gm45 - without this patch the bsd thing is
forever stuck since the seqno updates never reach the status page.
Tbh I have no idea how this ever worked without rewriting the hws
registers after a gpu reset.
To satisfy my OCD also give the functions a bit more consistent names:
- Use status_page everywhere, also for the physical addressed one.
- Use init for the allocation part and setup for the register setup
part consistently.
Long term I'd really like to share the hw init parts completely
between gpu reset, resume and driver load, i.e. to call
i915_gem_init_hw instead of the individual pieces we might need.
v2: Add the missing paragraph to the commit message about what bug
exactly this patch here fixes.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65495
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only execbuffer needed all the parameters on i915_add_request().
By putting __i915_add_request behind macro, all current callsites
become cleaner. Following patch will introduce a new parameter
for __i915_add_request. With this patch, only the relevant callsite
will reflect the change making commit smaller and easier to understand.
v2: _i915_add_request as function name (Chris Wilson)
v3: change name __i915_add_request and fix ordering of params (Ben Widawsky)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we reset and restart a ring, we also want to clear any existing
hangcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use the correct lock to protect PM interrupt regs, this was
accidentally lost from earlier (Haihao)
Fix return types (Ben)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The motivation here is we're going to add some new interrupt definitions
and handling outside of the GT interrupts which is all we've managed so
far (with some RPS exceptions). By consolidating the names in the future
we can make thing a bit cleaner as we don't need to define register
names twice, and we can leverage pretty decent overlap in HW registers
since ILK.
To explain briefly what is in the comments: there are two sets of
interrupt masking/enabling registers. At least so far, the definitions
of the two sets overlap. The old code setup distinct names for
interrupts in each set, ie. one for global, and one for ring. This made
things confusing when using the wrong defines in the wrong places.
rebase: Modified VLV bits
v2: Renamed GT_RENDER_MASTER to GT_RENDER_CS_MASTER (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's overkill on older gens, but it's useful for newer gens.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Add set_seqno which didn't exist before rebase (Haihao)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Historically we considered the render ring to have special flush
semantics and everything else to fall under a more general umbrella.
Probably by coincidence more than anything we decided to make the bsd
ring have the default *other* flush. As the new vebox ring exposes, the
bsd ring is actually the weird one. Doing this allows us to call
gen6_ring_flush for the vebox because calling blt_ring_flush would be
weird...
This patch should have no functional change.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like the other rings, the VECS supports semaphores. The semaphore stuff
is a bit wonky so this patch on it's own should be nice for review.
This patch should have no functional impact.
v2: Fix the English parts of clarification (again, register names were
right, text was reversed) (Damien)
Restore the still valid invariant. (Damien)
The bsd semaphore register should be MI_SEMAPHORE_SYNC_VVE (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The video enhancement command streamer is a new ring on HSW which does
what it sounds like it does. This patch provides the most minimal
inception of the ring.
In order to support a new ring, we need to bump the number. The patch
may look trivial to the untrained eye, but bumping the number of rings
is a bit scary. As such the patch is not terribly useful by itself, but
a pretty nice place to find issues during a bisection.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This replaces the existing MBOX update code with a more generalized
calculation for emitting mbox updates. We also create a sentinel for
doing the updates so we can more abstractly deal with the rings.
When doing MBOX updates the code must be aware of the /other/ rings.
Until now the platforms which supported semaphores had a fixed number of
rings and so it made sense for the code to be very specialized
(hardcoded).
The patch does contain a functional change, but should have no
behavioral changes.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphores are tied very closely to the rings in the GPU. Trivial patch
adds comments to the existing code so that when we add new rings we can
include comments there as well. It also helps distinguish the ring to
semaphore mailbox interactions by using the ringname in the semaphore
data structures.
This patch should have no functional impact.
v2: The English parts (as opposed to register names) of the comments
were reversed. (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix to return -ENOMEM in the kmap() error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of relying in acthd, track ring seqno progression
to detect if ring has hung.
v2: put hangcheck stuff inside struct (Chris Wilson)
v3: initialize hangcheck.seqno (Ben Widawsky)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We did not mention the workaround name when implementing those. This
should help us track what we already implement.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bit controlling whether PIPE_CONTROL DW/QW write targets
the global GTT or PPGTT moved moved from DW 2 bit 2 to
DW 1 bit 24 on IVB.
I verified on IVB that the fix is in fact effective. Without the fix
none of the scratch writes actually landed in the pipe control page.
With the fix the writes show up correctly.
v2: move PIPE_CONTROL_GLOBAL_GTT_IVB setup to where other flags are set
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already print the HWS addresses during init, so do the same for the
pipe control page. Reduces guesswork when looking at hex addresses
later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This pulls in most of Linus tree up to -rc6, this fixes the worst lockdep
reported issues and re-enables fbcon lockdep.
(not the fbcon maintainer)
* 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux: (529 commits)
Revert "Revert "console: implement lockdep support for console_lock""
fbcon: fix locking harder
fb: Yet another band-aid for fixing lockdep mess
fb: rework locking to fix lock ordering on takeover
On SNB, if bit 13 of GFX_MODE, Flush TLB Invalidate Mode, is not set to 1,
the hardware can not program the scanline values. Those scanline values
then control when the signal is sent from the display engine to the render
ring for MI_WAIT_FOR_EVENTs. Note setting this bit means that TLB
invalidations must be performed explicitly through the appropriate bits
being set in PIPE_CONTROL.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52311
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a required workarounds for all products, especially on gen6+
where it causes the command streamer to fail to parse instructions
following a WAIT_FOR_EVENT. We use WAIT_FOR_EVENT for synchronising
between the GPU and the display engines, and so this bit being unset may
cause hangs.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52311
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When machine was rebooted or module was reloaded,
gem_hw_init() set last_seqno to be identical to next_seqno.
This lead to situation that waits for first ever request
always passed immediately regardless if it was actually
executed.
Use gem_set_seqno() to be consistent how hw is
initialized on init, wrap and on resume.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And to make Ben Widawsky happier, use the gpu_error instead of
the entire device as the argument in some functions.
Drop the outdated comment on ->wedged for now, a follow-up patch will
change the semantics and add a proper comment again.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has been sprinkled all over the place in dev_priv. I think
it'd be good to also move all the code into a separate file like
i915_gem_error.c, but that's for another patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have enough info to not use the intel_gtt bridge stuff.
v2: Move setup of mappable_base above the legacy init stuff because we
still need that on older platforms. (Daniel)
v3: Remove the dev_priv hunk which was rebased in by accident
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Hardware status page needs to have proper seqno set
as our initial seqno can be arbitrary. If initial seqno is close
to wrap boundary on init and i915_seqno_passed() (31bit space)
refers to hw status page which contains zero, errorneous result
will be returned.
v2: clear mboxes and set hws page directly instead of going
through rings. Suggested by Chris Wilson.
v3: hws needs to be updated for all gens. Noticed by Chris
Wilson.
References: https://bugs.freedesktop.org/show_bug.cgi?id=58230
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for setting per ring initial seqno values
add ring::set_seqno().
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that Chris Wilson demonstrated that the key for stability on early
gen 2 is to simple _never_ exchange the physical backing storage of
batch buffers I've tried a stab at a kernel solution. Doesn't look too
nefarious imho, now that I don't try to be too clever for my own good
any more.
v2: After discussing the various techniques, we've decided to always blit
batches on the suspect devices, but allow userspace to opt out of the
kernel workaround assume full responsibility for providing coherent
batches. The principal reason is that avoiding the blit does improve
performance in a few key microbenchmarks and also in cairo-trace
replays.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet:
- Drop the hunk which uses HAS_BROKEN_CS_TLB to implement the ring
wrap w/a. Suggested by Chris Wilson.
- Also add the ACTHD check from Chris Wilson for the error state
dumping, so that we still catch batches when userspace opts out of
the w/a.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If wrap just happened we need to prevent emitting waits for
pre wrap values. Detect this and emit no-ops instead.
v2: Use olr > seqno to detect wrap instead of *seqno == 0
as suggested by Chris Wilson.
v3: Use last used seqno to detect the wraparound. From
Chris Wilson
v4: Fixed unnecessary last_seqno assigment
References: https://bugs.freedesktop.org/show_bug.cgi?id=57967
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If there are pre-wrap values in semaphore-mbox registers after wrap,
syncing against some after-wrap request will complete immediately.
Fix this by emitting ring commands to set mbox registers to zero
when the wrap happens.
v2: Use __intel_ring_begin to emit ring commands, from
Chris Wilson.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add a small comment to handle_seqno_wrap.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for handling ring seqno wrapping, split
intel_ring_begin into helper part which doesn't allocate
seqno.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From BSpec:
"If the Ring Buffer Head Pointer and the Tail Pointer are on the same
cacheline, the Head Pointer must not be greater than the Tail
Pointer."
The easiest way to enforce this is to reduce the reported ring space.
References:
Gen2 BSpec "1. Programming Environment" / 1.4.4.6 "Ring Buffer Use"
Gen3 BSpec "vol1c Memory Interface Functions" / 2.3.4.5 "Ring Buffer Use"
Gen4+ BSpec "vol1c Memory Interface and Command Stream" / 5.3.4.5 "Ring Buffer Use"
v2: Include the exact BSpec references in the description
v3: s/64/I915_RING_FREE_SPACE, and add the BSpec information to the code
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the wait for the ring to be clear with the more common wait for
the ring to be idle. The principle advantage is one less exported
intel_ring_wait function, and the removal of a hardcoded value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the work by Mika Kuoppala, we realised that we need to handle
seqno wraparound prior to committing our changes to the ring. The most
obvious point then is to grab the seqno inside intel_ring_begin(), and
then to reuse that seqno for all ring operations until the next request.
As intel_ring_begin() can fail, the callers must already be prepared to
handle such failure and so we can safely add further checks.
This patch looks like it should be split up into the interface
changes and the tweaks to move seqno wrapping from the execbuffer into
the core seqno increment. However, I found no easy way to break it into
incremental steps without introducing further broken behaviour.
v2: Mika found a silly mistake and a subtle error in the existing code;
inside i915_gem_retire_requests() we were resetting the sync_seqno of
the target ring based on the seqno from this ring - which are only
related by the order of their allocation, not retirement. Hence we were
applying the optimisation that the rings were synchronised too early,
fortunately the only real casualty there is the handling of seqno
wrapping.
v3: Do not forget to reset the sync_seqno upon module reinitialisation,
ala resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=863861
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> [v2]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bspec was recently updated to remove the ability to update the
semaphore using the MI_SEMAPHORE_BOX command, the ability to wait upon
the semaphore value remained. Instead the advice is to update the
register using the MI_LOAD_REGISTER_IMM command. In cursory testing,
semaphores continue to function - the question is whether this fixes
some of the deadlocks where the semaphore registers contained stale
values?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By always setting up the HWS register for both physical and virtual
address variations during render ring we can reduce the number of
different special cases that get set up at varying different times
during module load.
Fixes regression from
commit c630119f43
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Oct 17 11:32:57 2012 +0200
drm/i915: don't save/restore HWS_PGA reg for kms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has been introduced in "drm/i915: TLB invalidation with
MI_FLUSH_DW requires a post-sync op".
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"If ENABLED, PIPE_CONTROL command will flush the in flight data written
out by render engine to Global Observation point on flush done. Also
Requires stall bit ([20] of DW1) set."
So set the stall bit to ensure proper invalidation.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So store into the scratch space of the HWS to make sure the invalidate
occurs.
v2: use GTT address space for store, clean up #defines (Chris)
v3: use correct #define in blt ring flush (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/1063252
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make intel_render_ring_init_dri and intel_init_ring_buffer symmetrical
with regards of workaround introduced by:
commit 27c1cbd06a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 9 13:59:46 2012 +0100
drm/i915/ringbuffer: Exclude last 2 cachlines of ring on 845g
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the introduction of per-process GTT space, the hardware designers
thought it wise to also limit the ability to write to MMIO space to only
a "secure" batch buffer. The ability to rewrite registers is the only
way to program the hardware to perform certain operations like scanline
waits (required for tear-free windowed updates). So we either have a
choice of adding an interface to perform those synchronized updates
inside the kernel, or we permit certain processes the ability to write
to the "safe" registers from within its command stream. This patch
exposes the ability to submit a SECURE batch buffer to
DRM_ROOT_ONLY|DRM_MASTER processes.
v2: Haswell split up bit8 into a ppgtt bit (still bit8) and a security
bit (bit 13, accidentally not set). Also add a comment explaining why
secure batches need a global gtt binding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: added hsw fixup.]
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h). They are now #included via drmP.h and drm_crtc.h via a preceding
patch.
Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..." work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Michel Thierry