EDIDs should be backward compatible, so don't bail if we see a version
of 3 (which is out there now) and print a message if we see something
newer, but allow it to be parsed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check whether the INTERLACE/DBLSCAN is supported by output device. If
not, the mode containing the flag of INTERLACE/DBLSCAN will be marked
as unsupported.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Should be,
edid_vendor[2] = (edid->mfg_id[1] & 0x1f) + '@';
Since vendor ID has only two bytes only, I am somewhat surprised why gcc
doesn't complain this.
Reported-by: Guo, Chaohong <chaohong.guo@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an include that isn't actually needed to prevent needless
rebuilds.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The readq/writeq really need to be static inline on the arches which
don't provide them.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, the PAGE_CACHE_WC would end up getting us a UC-only mapping, and
the write performance of GTT maps dropped 10x.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: cleaned up unused var]
Signed-off-by: Eric Anholt <eric@anholt.net>
This is a baby-step in the direction of having finer-grained
locking than the struct_mutex. Specifically, this will enable
new debugging code to read the active list for printing out
GPU state when the GPU is wedged, (while the struct_mutex is
held, of course).
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: indentation fix]
Signed-off-by: Eric Anholt <eric@anholt.net>
This brings SDVO TV support from 2D driver, including origin
fix f1ca56e17d0 and later fix 2fcf4fcccfe. Also fix wrong modeline
definitions for SDVO TV.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix compile error of intel_sdvo_debug_response(),
and explicit use KERN_DEBUG for printk.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only set TV DAC in property change seems doesn't work, we have to
setup whole crtc pipe which assigned to TV alone.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: Note that this should also fix the oops at startup with new 2D]
Signed-off-by: Eric Anholt <eric@anholt.net>
If there's no real property change, don't need to set TV mode again.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: checkpatch.pl fix]
Signed-off-by: Eric Anholt <eric@anholt.net>
udelay() of 20 milliseconds really ought to just use mdelay(), that avoids
the various wrap scenarios and also is more readable
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add VGA port hotplug detection to the i915 driver. When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: Eric Anholt <eric@anholt.net>
"struct tty_driver *" lies in m->private not in v which is
SEQ_TOKEN_START which is 1 which is enough to trigger NULL dereference
next line:
BUG: unable to handle kernel NULL pointer dereference at 000000ad
IP: [<c040d689>] uart_proc_show+0xe/0x2b0
Noticed by Linus.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: guard against pre-ACPI 3 e820 code not updating %ecx
Commit 64ef895798 ("qeth: remove EDDP")
removed the qeth_core_offl.[hc] files, but ended up doing so by just
patching them to zero size, rather than removing them properly.
Actually remove the files.
Reported-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IGD device only has last 1 page used by GTT. This should match the AGP gart
code.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
drm_get_edid will store edid into raw_edid, so when freeing edid memory,
at the same time clean raw_edid pointer.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Note that raw_edid is not currently used anywhere]
Signed-off-by: Eric Anholt <eric@anholt.net>
Impact: BIOS bug safety
For pre-ACPI 3 BIOSes, pre-initialize the end of the e820 buffer just
in case the BIOS returns an unchanged %ecx but without actually
touching the ACPI 3 extended flags field.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86/setup' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: ACPI 3, BIOS workaround for E820-probing code
x86, setup: preemptively save/restore edi and ebp around INT 15 E820
x86, setup: mark %esi as clobbered in E820 BIOS call
Indicates something is wrong with the mapping; and apparently triggers
in current kernels.
Signed-off-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes all the tiling problems with the 2d ddx. glxgears still doesn't work.
Changes:
- fix a copy&paste error in i8xx fence reg setup. It resulted in an at most a
512KB offset of the fence reg window, so was only visible sometimes.
- add tests for stride and object size constrains (also for i915 and 1965 class
hw). Userspace seems to have an of-by-one bug there, which changes the fence
size by at most 512KB due to an overflow.
- because i8xx hw is quite old (and therefore not as well-tested) I left 2 debug
WARN_ONs in the i8xx fence reg setup code to hopefully catch any further
overflows in the bit-fields. Lastly there's one small change to make the
alignment checks more consistent.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=20289
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (58 commits)
SUNRPC: Ensure IPV6_V6ONLY is set on the socket before binding to a port
NSM: Fix unaligned accesses in nsm_init_private()
NFS: Simplify logic to compare socket addresses in client.c
NFS: Start PF_INET6 callback listener only if IPv6 support is available
lockd: Start PF_INET6 listener only if IPv6 support is available
SUNRPC: Remove CONFIG_SUNRPC_REGISTER_V4
SUNRPC: rpcb_register() should handle errors silently
SUNRPC: Simplify kernel RPC service registration
SUNRPC: Simplify svc_unregister()
SUNRPC: Allow callers to pass rpcb_v4_register a NULL address
SUNRPC: rpcbind actually interprets r_owner string
SUNRPC: Clean up address type casts in rpcb_v4_register()
SUNRPC: Don't return EPROTONOSUPPORT in svc_register()'s helpers
SUNRPC: Use IPv4 loopback for registering AF_INET6 kernel RPC services
SUNRPC: Set IPV6ONLY flag on PF_INET6 RPC listener sockets
NFS: Revert creation of IPv6 listeners for lockd and NFSv4 callbacks
SUNRPC: Remove @family argument from svc_create() and svc_create_pooled()
SUNRPC: Change svc_create_xprt() to take a @family argument
SUNRPC: svc_setup_socket() gets protocol family from socket
SUNRPC: Pass a family argument to svc_register()
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (33 commits)
ext4: Regularize mount options
ext4: fix locking typo in mballoc which could cause soft lockup hangs
ext4: fix typo which causes a memory leak on error path
jbd2: Update locking coments
ext4: Rename pa_linear to pa_type
ext4: add checks of block references for non-extent inodes
ext4: Check for an valid i_mode when reading the inode from disk
ext4: Use WRITE_SYNC for commits which are caused by fsync()
ext4: Add auto_da_alloc mount option
ext4: Use struct flex_groups to calculate get_orlov_stats()
ext4: Use atomic_t's in struct flex_groups
ext4: remove /proc tuning knobs
ext4: Add sysfs support
ext4: Track lifetime disk writes
ext4: Fix discard of inode prealloc space with delayed allocation.
ext4: Automatically allocate delay allocated blocks on rename
ext4: Automatically allocate delay allocated blocks on close
ext4: add EXT4_IOC_ALLOC_DA_BLKS ioctl
ext4: Simplify delalloc code by removing mpage_da_writepages()
ext4: Save stack space by removing fake buffer heads
...
Also ensure that we use the protocol family instead of the address
family when calling sock_create_kern().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This fixes unaligned accesses in nsm_init_private() when
creating nlm_reboot keys.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: try to free metadata pages when we free btree blocks
Btrfs: add extra flushing for renames and truncates
Btrfs: make sure btrfs_update_delayed_ref doesn't increase ref_mod
Btrfs: optimize fsyncs on old files
Btrfs: tree logging unlink/rename fixes
Btrfs: Make sure i_nlink doesn't hit zero too soon during log replay
Btrfs: limit balancing work while flushing delayed refs
Btrfs: readahead checksums during btrfs_finish_ordered_io
Btrfs: leave btree locks spinning more often
Btrfs: Only let very young transactions grow during commit
Btrfs: Check for a blocking lock before taking the spin
Btrfs: reduce stack in cow_file_range
Btrfs: reduce stalls during transaction commit
Btrfs: process the delayed reference queue in clusters
Btrfs: try to cleanup delayed refs while freeing extents
Btrfs: reduce stack usage in some crucial tree balancing functions
Btrfs: do extent allocation and reference count updates in the background
Btrfs: don't preallocate metadata blocks during btrfs_search_slot
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (59 commits)
ide-floppy: do not complete rq's prematurely
ide: be able to build pmac driver without IDE built-in
ide-pmac: IDE cable detection on Apple PowerBook
ide: inline SELECT_DRIVE()
ide: turn selectproc() method into dev_select() method (take 5)
MAINTAINERS: move old ide-{floppy,tape} entries to CREDITS (take 2)
ide: move data register access out of tf_{read|load}() methods (take 2)
ide: call {in|out}put_data() methods from tf_{read|load}() methods (take 2)
ide-io-std: shorten ide_{in|out}put_data()
ide: rename IDE_TFLAG_IN_[HOB_]FEATURE
ide: turn set_irq() method into write_devctl() method
ide: use ATA_HOB
ide-disk: use ATA_ERR
ide: add support for CFA specified transfer modes (take 3)
ide-iops: only clear DMA words on setting DMA mode
ide: identify data word 53 bit 1 doesn't cover words 62 and 63 (take 3)
au1xxx-ide: auide_{in|out}sw() should be static
ide-floppy: use ide_pio_bytes()
ide-{floppy,tape}: fix padding for PIO transfers
ide: remove CONFIG_BLK_DEV_IDEDOUBLER config option
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
sn2_ptc_init() has what looks like a cut-n-paste error. Fix it.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cio: online_store - trigger recognition for boxed devices
[S390] cio: disallow online setting of device in transient state
[S390] cio: introduce notifier for boxed state
[S390] cio: introduce ccw_device_schedule_sch_unregister
[S390] cio: wake up on failed recognition
[S390] fix hypfs build failure
[PATCH] sysrq: include interrupt.h instead of irq.h
The current logic for dmi matching in efifb does not allow efifb to load
on all hardware that we can dmi match for.
For a real world example, boot with elilo (3.7 or 3.8 vanilla) and on a
Apple (MacBook) and EFI framebuffer driver will not load (you will have no
video). This specific hardware is efi v1.10, so we have UGA and not GOP.
Without special bootloader magic (i.e. extra elilo patches for UGA
graphics detection) no screen info will be passed to the kernel and as a
result efifb will not load.
This patch allows the dmi match to happen by moving it to earlier in
efifb_init, and sets the video type (in set_system) so that efifb can load
when we have a valid dmi match and already know the specifics of the
hardware.
Without this patch the efifb driver will fail to load in the event screen
info is not found and passed in by the bootloader, being that we will
never get to look for a dmi match. A primary reason for matching with dmi
is because not all bootloaders detect the video info properly. The
solution is that in the event of a dmi match, we should set
screen_info.orig_video_isVGA. Most bootloaders fail to set screen info on
Apple hardware, and this is a big problem for people who use Apple
hardware.
Tested on a MacBook SantaRosa with elilo-3.8 (vanilla) and resolves the
issue, the dmi match now works, EFI framebuffer now loads and video works.
Signed-off-by: Brian Maly <bmaly@redhat.com>
Acked-by: Huang Ying <ying.huang@intel.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove Kconfig option for tridentfb acceleration. The acceleration can be
switched off with modules "noaccel" parameter.
The acceleration for Trident chips was fixed in the 2.6.27 kernel.
Also, add CyberXXX and CyberBlade names to Kconfig option's name. It should
make easier to find the tridentfb choice for cyblafb driver's users. The
cyblafb driver has been replaced by the tridentfb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Save one fifo entry on cursor enabling and disabling.
Save another fifo entry for FB_CUR_SETPOS operation by removing redundant one.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A hardware cursor is left enabled in the fb_set_par() which is called when a
new console is created. This is inconsistent with software cursor's
behaviour.
Also, this makes a hardware cursor always visible in the Xfbdev (Xorg kdrive)
server.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Risto Suominen <risto.suominen@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove mutex from the nvidiafb_open/nvidiafb_release functions as these
operations are mutexed at fb layer.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add suspend/resume for the Acer Travelmate 290D/292LMi with the following
graphic-chip:
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV350
[Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA controller])
Subsystem: Acer Incorporated [ALI] TravelMate 290 [1025:005a]
Flags: bus master, 66MHz, medium devsel, latency 128, IRQ 10
Memory at a8000000 (32-bit, prefetchable) [size=128M]
I/O ports at c100 [size=256]
Memory at e0010000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at a0000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Capabilities: [50] Power Management version 2
Kernel driver in use: radeonfb
Kernel modules: radeonfb
Signed-off-by: Wolfgang Kroener <lkml@azog.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The blank operation should receive FB_BLANK_POWERDOWN, not VESA_POWERDOWN.
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrea Righi <righi.andrea@gmail.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Cc: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the vbemode option is used, uvesafb calls fb_get_mode() without first
setting the resolution in info->var. This results in a division by zero
in fb_get_mode(), as evidenced e.g. in [1]. Fix this by ensuring the
info->var structure is populated before fb_get_mode() is called.
[1] http://bugzilla.kernel.org/show_bug.cgi?id=11661#c37
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A tridentfb driver has all the functionality of the cyblafb driver without
the bugs of the latter.
Changes to the tridentfb driver:
- FBINFO_READS_FAST added to the tridentfb. The cyblafb used a blitter
for scrolling which is faster than color expansion on Cyberblade
chipsets. The blitter is slower on a discrete Blade3D core. Use the
blitter for scrolling in the tridentfb only for integrated Blade3D
cores. Now, scrolling speed is about equal for the tridentfb and the
cyblafb.
- a copyright notice addition is done on request of Jani Monoses (the
first author of the tridentfb).
Tested on AGP Blade3D card and PCChips
M787CLR motherboard: VIA C3 cpu +
VT8601 north bridge (aka Cyberblade/i1).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Jani Monoses" <jani@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the newer Samsung devices, such as found in the S3C2443,
S3C6400 or S3C6410 series SoC.
It currently does not support all the alpha- or chroma-key options but it
will support more exporting more than one framebuffer ready for adding
overlay and blending functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no entry for n411.c to be built, include one in Makefile.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise this will already return 0 if iteration MAXLOOP-2 occurs in the
first loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie