Add marvell_nand driver which aims at replacing the existing pxa3xx_nand
driver.
The new driver intends to be easier to understand and follows the brand
new NAND framework rules by implementing hooks for every pattern the
controller might support and referencing them inside a parser object
that will be given to the core at each ->exec_op() call.
Raw accessors are implemented, useful to test/debug memory/filesystem
corruptions. Userspace binaries contained in the mtd-utils package may
now be used and their output trusted.
Most of the DT nodes using the old driver kept non-optimal timings from
the bootloader (even if there was some mechanisms to derive them if the
chip was ONFI compliant). The new default is to implement
->setup_data_interface() and follow the core's decision regarding the
chip.
Thanks to the improved timings, implementation of ONFI mode 5 support
(with EDO managed by adding a delay on data sampling), merging the
commands together and optimizing writes in the command registers, the
new driver may achieve faster throughputs in both directions.
Measurements show an improvement of about +23% read throughput and +24%
write throughput. These measurements have been done with an
Armada-385-DB-AP (4kiB NAND pages forced in 4-bit strength BCH ECC
correction) using the userspace tool 'flash_speed' from the MTD test
suite.
Besides these important topics, the new driver addresses several
unsolved known issues in the old driver which:
- did not work with ECC soft neither with ECC none ;
- relied on naked read/write (which is unchanged) while the NFCv1
embedded in the pxa3xx platforms do not implement it, so several
NAND commands did not actually ever work without any notice (like
reading the ONFI PARAM_PAGE or SET/GET_FEATURES) ;
- wrote the OOB data correctly, but was not able to read it correctly
past the first OOB data chunk ;
- did not retrieve ECC bytes ;
- used device tree bindings that did not allow more than one NAND chip,
and did not allow to choose the correct chip select if not
incrementing from 0. Plus, the Ready/Busy line used had to be 0.
Old device tree bindings are still supported but deprecated. A more
hierarchical view has to be used to keep the controller and the NAND
chip structures clearly separated both inside the device tree and also
in the driver code.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The GPMI nand Kconfig help texts mentions that the GPMI nand driver
might conflict with SD cards. The only conflict there might really
be is that both controllers use the same pins, but this is resolved
by the pincontroller setup in the device tree. In any way the GPMI
driver can safely be enabled, the text is just wrong. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
More and more SoCs use the pxa3xx_nand driver for their controller but
the list of them was not updated. This patch add the last SoCs using the
driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The controller supported by the pxa3xx_nand driver is also available on
the mvebu 64-bit SoCs, such as the Armada 7K and Armada 8K SoCs. This
patch updates the Kconfig dependency to allow building the kernel for
this SoC family too.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller IP can adapt the NAND controller timings dynamically.
Implement the ->setup_data_interface() hook to support this feature.
Note that it's not supported on at91rm9200 because this SoC has a
completely different SMC block, which is not supported yet.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Mediatek NAND driver is only needed for a specific
platform, so avoid cluttering the configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Hisilicon NAND driver is only needed for a specific
platform, so avoid cluttering the configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is a complete rewrite of the driver whose main purpose is to
support the new DT representation where the NAND controller node is now
really visible in the DT and appears under the EBI bus. With this new
representation, we can add other devices under the EBI bus without
risking pinmuxing conflicts (the NAND controller is under the EBI
bus logic and as such, share some of its pins with other devices
connected on this bus).
Even though the goal of this rework was not necessarily to add new
features, the new driver has been designed with this in mind. With a
clearer separation between the different blocks and different IP
revisions, adding new functionalities should be easier (we already
have plans to support SMC timing configuration so that we no longer
have to rely on the configuration done by the bootloader/bootstrap).
Also note that we no longer have a custom ->cmdfunc() implementation,
which means we can now benefit from new features added in the core
implementation for free (support for new NAND operations for example).
The last thing that we gain with this rework is support for multi-chips
and multi-dies chips, thanks to the clean NAND controller <-> NAND
devices representation.
During this transition we also dropped support for AVR32 SoCs which
should soon disappear from mainline (removal of the AVR32 arch is
planned for 4.12).
This new driver has been tested on several platforms (at91sam9261,
at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not
introduce regressions, and it's worth mentioning that old bindings are
still supported (which partly explain the positive diffstat).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
All of these macros are not used at all.
CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR is not used for anything but
defining SCRATCH_REG_ADDR. The config option should go away as well.
I am removing some register macros. They are not used, and do not
exist in recent IP versions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As NAND support for Freescale/NXP IFC controller is available on
LS1021A, the dependency for LS1021A is added.
LS1021A is an earlier product and is not compatible with later
LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MTD_NAND_IDS is selected by MTD_NAND, which makes it useless. Remove
the Kconfig option and link nand_ids.o into the nand.o object file.
Doing that also prevents creating an extra nand_ids.ko module when
MTD_NAND is activated as a module.
Since nand_ids.c is no longer compiled as a standalone module and the
nand_manuf_ids/nand_flash_ids symbols are only used in nand_base.c, we
can get rid of the MODULE_XXX() and EXPORT_SYMBOL() definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The oxnas NAND driver is only needed for a specific platform, do
not propose it on other platforms unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Cc: Rob Herring <robh@kernel.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The FSMC driver has an execution path and a header file in
<linux/mtd/fsmc.h> that serves to support passing in platform
data through board files, albeit no upstream users of this
mechanism exist.
The header file also contains function headers for functions that
do not exist in the kernel.
Delete this and move the platform data struct, parsing and
handling into the driver, assume we are using OF and make the
driver depend on OF, remove the ifdefs making that optional.
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fix build errors on arch/um, which does not support HAS_IOMEM,
while the oxnas_nand.c driver uses interfaces that are
supplied by HAS_IOMEM.
(loadable module build:)
ERROR: "devm_ioremap_resource" [drivers/mtd/nand/oxnas_nand.ko] undefined!
or (built-in build:)
drivers/built-in.o: In function `oxnas_nand_probe':
drivers/mtd/nand/oxnas_nand.c:102: undefined reference to `devm_ioremap_resource'
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The xway_nand driver accesses the ltq_ebu_membase symbol which is not
exported. This also should not get exported and we should handle the
EBU interface in a better way later. This quick fix just deactivated
support for building as module.
Fixes: 99f2b10792 ("mtd: lantiq: Add NAND support on Lantiq XWAY SoC.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver supports the NAND Flash controller embedded in recent
Tango chips, such as SMP8758 and SMP8759.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Removing CONFIG_MTD_NAND_S3C2410_HWECC option and adding a ecc_mode
field in the drivers's platform data structure so it can be selectable
via platform data.
Also setting this field to NAND_ECC_SOFT in all boards using this
driver since none of them had CONFIG_MTD_NAND_S3C2410_HWECC enabled.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add NAND driver to support the Oxford Semiconductor OX820 NAND Controller.
This is a simple memory mapped NAND controller with single chip select and
software ECC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some Keystone devices (e.g. K2G) include a OMAP NAND IP.
Allow the NAND driver to be usable for both
Keystone and OMAP devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Config MTD_NAND_FSL_IFC is already located inside 'if MTD_NAND'
statment, so there's no need to explicitly specify it as a dependency.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MTD_NAND_FSL_ELBC selects FSL_LBC that in turn depends on FSL_SOC, so
depending on PPC instead of FSL_SOC leads to this message:
warning: (MPC836x_RDK && MTD_NAND_FSL_ELBC &&
MTD_NAND_FSL_UPM) selects FSL_LBC which has unmet direct
dependencies (FSL_SOC)
when doing
make ARCH=powerpc \
CROSS_COMPILE=powerpc-e500v2-linux-gnuspe- \
allmodconfig"
Changing dependency to FSL_SOC fixes that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Aeb
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.8' of github.com:linux-nand/linux into mtd
Pull NAND changes from Boris Brezillon:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
This patch enables IFC NAND support on ARM layerscape platform.
It fixes the dependency to enable NAND. The include files are being modified
to ensure complilation for both PowerPC and ARM architectures.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Instead of hacking this into the plat_nand driver just make this a
normal nand driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add support for mediatek's SDG1 NFC nand controller embedded in SoC
2701
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Xiaolei Li <xiaolei.li@mediatek.com>
The Qualcomm NAND controller is found in SoCs like IPQ806x, MSM7xx,
MDM9x15 series.
It exists as a sub block inside the IPs EBI2 (External Bus Interface 2)
and QPIC (Qualcomm Parallel Interface Controller). These IPs provide a
broader interface for external slow peripheral devices such as LCD and
NAND/NOR flash memory or SRAM like interfaces.
We add support for the NAND controller found within EBI2. For the SoCs
of our interest, we only use the NAND controller within EBI2. Therefore,
it's safe for us to assume that the NAND controller is a standalone block
within the SoC.
The controller supports 512B, 2kB, 4kB and 8kB page 8-bit and 16-bit NAND
flash devices. It contains a HW ECC block that supports BCH ECC (4, 8 and
16 bit correction/step) and RS ECC(4 bit correction/step) that covers main
and spare data. The controller contains an internal 512 byte page buffer
to which we read/write via DMA. The EBI2 type NAND controller uses ADM DMA
for register read/write and data transfers. The controller performs page
reads and writes at a codeword/step level of 512 bytes. It can support up
to 2 external chips of different configurations.
The driver prepares register read and write configuration descriptors for
each codeword, followed by data descriptors to read or write data from the
controller's internal buffer. It uses a single ADM DMA channel that we get
via dmaengine API. The controller requires 2 ADM CRCIs for command and
data flow control. These are passed via DT.
The ecc layout used by the controller is syndrome like, but we can't use
the standard syndrome ecc ops because of several reasons. First, the amount
of data bytes covered by ecc isn't same in each step. Second, writing to
free oob space requires us writing to the entire step in which the oob
lies. This forces us to create our own ecc ops.
One more difference is how the controller accesses the bad block marker.
The controller ignores reading the marker when ECC is enabled. ECC needs
to be explicity disabled to read or write to the bad block marker. The
nand_bbt helpers library hence can't access BBMs for the controller.
For now, we skip the creation of BBT and populate chip->block_bad and
chip->block_markbad helpers instead.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Not every arch has io memory nor can this driver ever work
on UML/i386.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a driver for NAND devices connected to the NEMC on JZ4780 SoCs, as
well as the hardware BCH controller. DMA is not currently implemented.
While older 47xx SoCs also have a BCH controller, they are incompatible
with the one in the 4780 due to differing register/bit positions, which
would make implementing a common driver for them quite messy.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: fixed a few small mistakes]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The build passes even if CONFIG_OF is undefined, but it makes sense
to let it depend on OF.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As of commit a521422ea4 ("ARM: shmobile: mackerel: Remove Legacy C
board code"), the Renesas SuperH FLCTL driver is no longer used on ARM
SH-Mobile SoCs. Restrict the dependencies, unless compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The BRCM NAND driver can be re-used for Broadcom ARM64 SoCs hence
this patch updates Kconfig to allow selection of MTD_NAND_BRCMNAND
for ARM64.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This adds hardware ECC support using the BCH encoder in the NFC IP.
The ECC encoder supports up to 32-bit correction by using 60 error
correction bytes. There is no sub-page ECC step, ECC is calculated
always across the whole page (up to 2k pages).
Limitations:
- HW ECC: Only 2K page with 64+ OOB.
- HW ECC: Only 24 and 32-bit error correction implemented.
Raw writes have been tested using the generic nand_write_page_raw
implementation. However, raw reads are currently not possible
because the controller need to know whether we are going to use
the ECC mode already at NAND_CMD_READ0 command time. At this point
we do not have the information whether it is a raw read or a
regular read at driver level...
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver supports Freescale NFC (NAND flash controller) found on
Vybrid (VF610), MPC5125, MCF54418 and Kinetis K70. The driver has
been tested using 8-bit and 16-bit NAND interface on the ARM based
Vybrid SoC VF500 and VF610 platform.
parameter page reading.
Limitations:
- Untested on MPC5125 and M54418.
- DMA and pipelining not used.
- 2K pages or less.
- No chip select, one NAND chip per controller.
- No hardware ECC.
Some paths have been hand-optimized and evaluated by measurements
made using mtd_speedtest.ko on a 100MB MTD partition.
Colibri VF50
eb write % eb read % page write % page read %
rel/opt 5175 11537 4560 11039
opt 5164 -0.21 11420 -1.01 4737 +3.88 10918 -1.10
none 5113 -1.20 11352 -1.60 4490 -1.54 10865 -1.58
Colibri VF61
eb write % eb read % page write % page read %
rel/opt 5766 13096 5459 12846
opt 5883 +2.03 13064 -0.24 5561 +1.87 12802 -0.34
none 5701 -1.13 12980 -0.89 5488 +0.53 12735 -0.86
rel = using readl_relaxed/writel_relaxed in optimized paths
opt = hand-optimized by combining multiple accesses into one read/write
The measurements have not been statistically verfied, hence use them
with care. The author came to the conclusion that using the relaxed
variants of readl/writel are not worth the additional code.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to user to see the core part of the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This core originated in Set-Top Box chips (BCM7xxx) but is used in a
variety of other Broadcom chips, including some BCM63xxx, BCM33xx, and
iProc/Cygnus. It's been used only on ARM and MIPS SoCs, so restrict it
to those architectures.
There are multiple revisions of this core throughout the years, and
almost every version broke register compatibility in some small way, but
with some effort, this driver is able to support v4.0, v5.0, v6.x, v7.0,
and v7.1. It's been tested on v5.0, v6.0, v6.1, v7.0, and v7.1 recently,
so there hopefully are no more lurking inconsistencies.
This patch adds just some library support, on which platform drivers can
be built.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
If NO_DMA=y:
drivers/built-in.o: In function `hisi_nfc_probe':
hisi504_nand.c:(.text+0x23e646): undefined reference to `dmam_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the support for hisilicon 504 NAND controller which is now used
by Hisilicon Soc Hip04.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The drivers/mtd/nand/gpio.c driver does not GPIO bitbang the complete
NAND protocol, but instead is GPIO _assisted_ -- a memory mapped interface
communicates commands and data, and only few control signals are connected
to GPIO pins.
Expand comments in the driver source and in the Kconfig description to
better reflect the very nature of the driver. The previous text could be
mistaken for complete GPIO bitbanging.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for the sunxi NAND Flash Controller (NFC).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: tweaked to fix ecc->steps issue]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The MTD_NAND_OMAP_BCH doesn't harm on legacy OMAP platforms
so don't state that it should be disabled for them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds a hidden option to build the omap_elm as a module, if
omap2_nand is a module (and similarly in the built-in case).
This fixes the following build error when omap2_nand is chosen built-in,
and omap_elm is chosen as a module:
drivers/built-in.o: In function `omap_nand_probe':
drivers/mtd/nand/omap2.c:2010: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1980: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1927: undefined reference to `elm_config'
drivers/built-in.o: In function `omap_elm_correct_data':
drivers/mtd/nand/omap2.c:1444: undefined reference to `elm_decode_bch_error_page'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=CKih
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
* tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd: (120 commits)
Fix index regression in nand_read_subpage
mtd: diskonchip: mem resource name is not optional
mtd: nand: fix mention to CONFIG_MTD_NAND_ECC_BCH
mtd: nand: fix GET/SET_FEATURES address on 16-bit devices
mtd: omap2: Use devm_ioremap_resource()
mtd: denali_dt: Use devm_ioremap_resource()
mtd: devices: elm: update DRIVER_NAME as "omap-elm"
mtd: devices: elm: configure parallel channels based on ecc_steps
mtd: devices: elm: clean elm_load_syndrome
mtd: devices: elm: check for hardware engine's design constraints
mtd: st_spi_fsm: Succinctly reorganise .remove()
mtd: st_spi_fsm: Allow loop to run at least once before giving up CPU
mtd: st_spi_fsm: Correct vendor name spelling issue - missing "M"
mtd: st_spi_fsm: Avoid duplicating MTD core code
mtd: st_spi_fsm: Remove useless consts from function arguments
mtd: st_spi_fsm: Convert ST SPI FSM (NOR) Flash driver to new DT partitions
mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct
mtd: st_spi_fsm: Supply the W25Qxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the S25FLxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back
...
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM and HAS_DMA to bypass build failures.
drivers/built-in.o: In function `flctl_probe':
drivers/mtd/nand/sh_flctl.c:1097: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `flctl_dma_fifo0_transfer':
drivers/mtd/nand/sh_flctl.c:368: undefined reference to `dma_map_single'
drivers/mtd/nand/sh_flctl.c:407: undefined reference to `dma_unmap_single'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit d2ae2e20fb ("driver/memory:Move
Freescale IFC driver to a common driver") introduces this build
regression into the mpc85xx_defconfig:
drivers/built-in.o: In function `fsl_ifc_nand_remove':
drivers/mtd/nand/fsl_ifc_nand.c:1147: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1147: undefined reference to `fsl_ifc_ctrl_dev'
drivers/built-in.o: In function `fsl_ifc_nand_probe':
drivers/mtd/nand/fsl_ifc_nand.c:1031: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1031: undefined reference to `fsl_ifc_ctrl_dev'
drivers/built-in.o: In function `match_bank':
drivers/mtd/nand/fsl_ifc_nand.c:1013: undefined reference to `convert_ifc_address'
drivers/built-in.o: In function `fsl_ifc_nand_probe':
drivers/mtd/nand/fsl_ifc_nand.c:1059: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1080: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1069: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1069: undefined reference to `fsl_ifc_ctrl_dev'
make: *** [vmlinux] Error 1
This happens because there is nothing to descend us into the
drivers/memory directory in the mpc85xx_defconfig. It wasn't
selecting CONFIG_MEMORY. So we never built drivers/memory/fsl_ifc.o
and so we have nothing to link the above symbols against.
Since the goal of the original commit was to relocate the driver to
an arch independent location, it only makes sense to relocate the
Kconfig setting there as well. But that alone won't fix the build
failure; for that we ensure whoever selects FSL_IFC also selects MEMORY.
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Keystone arch has compatible nand device, so reuse it.
In case with Keystone it depends on TI_AEMIF because AEMIF
driver is responsible to set timings.
See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Geert Uytterhoeven