Atomic transfers are not only about sending messages like the original
wording suggested. Speak of 'accessing' now like in i2c.h.
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I don't plan to support every EEPROM type, but the 24c512 ones need a
tiny code update, so let's have that upstream.
Reported-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch adds a algorithm to calculate some ac-timing parameters
which can fully meet I2C Spec.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i801_add_mux() fills in the GPIO lookup table by manually populating an
array of gpiod_lookup structures. Use the existing GPIO_LOOKUP() helper
macro instead, to relax a dependency on the gpiod_lookup structure's
member names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20200511145257.22970-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A call to 'i2c_demux_deactivate_master()' is missing in the error handling
path, as already done in the remove function.
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use a mutex to protect access to idev->msg_len, idev->buf, etc. which
are modified by both altr_i2c_xfer_msg() and altr_i2c_isr().
This is the minimal fix for easy backporting. A cleanup to remove the
spinlock will be added later.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_gpiod_get() usually calls gpio_request_enable() for non-strict pinmux
drivers. These puts the pins in GPIO mode, whithout notifying the pinctrl
driver. At this point, the I2C bus no longer owns the pins. To mux the
pins back to the I2C bus, we use the pinctrl driver to change the state
of the pins to GPIO, before using devm_gpiod_get(). After the pins are
received as GPIOs, we switch theer pinctrl state back to the default
one,
Fixes: d3d3fdcc4c ("i2c: at91: implement i2c bus recovery")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Allow slave mode for PCI enumerated devices by calling a common i2c_dw_probe()
instead of i2c_dw_probe_master().
While dropping dependency to platform driver in slave module, move its
configuration section above, closer to core.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As a preparatory patch to support slave mode for PCI enumerated devices rename
i2c_dw_probe() to i2c_dw_probe_master() and split common i2c_dw_probe() as
inline helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since we have available helper to configure master mode, let's use it
in the PCI driver instead of spread open-coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move configuration routines to respective modules, i.e. master and slave.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() instead of
platform_get_resource() + devm_ioremap_resource().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Tegra210 has an extra instance of the I2C controller that is in the
domain of host1x and usually used for camera use-cases. The programming
model for the VI variant of the controller is roughly the same as for
the other variants, except that the I2C registers start at an offset
and are spaced further apart. VI I2C also doesn't support slave mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use master-abort to send the stop condition after an address cycle
rather than resetting the controller.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If we timeout during a message transfer, the control register may
contain bits that cause an action to be set. Read-modify-writing the
register leaving these bits set may trigger the hardware to attempt
one of these actions unintentionally.
Always clear these bits when cleaning up after a message or after
a timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove unnecessary show_state() in the loop inside
i2c_pxa_pio_set_master(), which can be unnecessarily verbose.
Remove the i2c_pxa_scream_blue_murder() in i2c_pxa_pio_xfer(), which
will trigger if we are probing the I2C bus and a slave does not
respond; this is a normal event, and not something to report.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ensure that the various timeout messages can identify where in the code
they were produced from to aid debugging.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Running i2cdetect on a PXA I2C adapter is very noisy; it complains
whenever a slave fails to respond to the address cycle. Since it is
normal to probe for slaves in this way, we should not fill the kernel
log. This is especially true with SFP modules that take a while to
respond on the I2C bus, and probing via the I2C bus is the only way to
detect that they are ready.
Fix this by changing the internal transfer return code from I2C_RETRY
to a new NO_SLAVE code (mapped to -ENXIO, as per the I2C documentation
for this condition, but we still return -EREMOTEIO to the I2C stack to
maintain long established driver behaviour.)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Most of i2c_pxa_pio_xfer() and i2c_pxa_xfer() are identical; the only
differences are that i2c_pxa_pio_xfer() may reset the bus, and they
use different underlying transfer functions. The retry loop is the
same. Consolidate these two functions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use a shorter SPDX identifier instead of pasting the whole license.
While here, replace duplicating PCA954x with PCA984x.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
device_create_file() is called the last in ->probe() but pca954x_cleanup(),
which is called earlier in error path, tries to remove never created file.
Move device_remove_file() call outside of pca954x_cleanup() to make it
slightly closer to what pca954x_init() is doing.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Refactor pca954x_irq_handler() to:
- use for_each_set_bit() macro
- use IRQ_RETVAL() macro
Above change makes code easy to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DMA transfer could be completed, but CPU (which handles DMA interrupt)
may get too busy and can't handle the interrupt in a timely manner,
despite of DMA IRQ being raised. In this case the DMA state needs to
synchronized before terminating DMA transfer in order not to miss the
DMA transfer completion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Boot CPU0 always handle I2C interrupt and under some rare circumstances
(like running KASAN + NFS root) it may stuck in uninterruptible state for
a significant time. In this case we will get timeout if I2C transfer is
running on a sibling CPU, despite of IRQ being raised. In order to handle
this rare condition, the IRQ status needs to be checked after completion
timeout.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
One of the I2C controllers on Tegra SoCs is typically connected to a
system PMIC, which provides controls for critical power supplies for
most platforms.
Some drivers, such as PCI, need to disable these regulators during a
very late stage during suspend and resume them at a very early stage
during resume.
To support these use-cases, keep interrupts disabled during suspend/
resume.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depending on the board design, the I2C controllers found on Tegra SoCs
may require pinmuxing in order to function. This is done as part of the
driver's runtime suspend/resume operations. However, the PM core does
not allow devices to go into runtime suspend during system sleep to
avoid potential races with the suspend/resume of their parents.
As a result of this, when Tegra SoCs resume from system suspend, their
I2C controllers may have lost the pinmux state in hardware, whereas the
pinctrl subsystem is not aware of this. To fix this, make sure that if
the I2C controller is not runtime suspended, the runtime suspend code is
still executed in order to disable the module clock (which we don't need
to be enabled during sleep) and set the pinmux to the idle state.
Conversely, make sure that the I2C controller is properly resumed when
waking up from sleep so that pinmux settings are properly restored.
This fixes a bug seen with DDC transactions to an HDMI monitor timing
out when resuming from system suspend.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reverts commit 9f42de8d4e.
It's not safe to use pm_runtime_force_{suspend,resume}(), especially
during the noirq phase of suspend. See also the guidance provided in
commit 1e2ef05bb8 ("PM: Limit race conditions between runtime PM
and system sleep (v2)").
Signed-off-by: Thierry Reding <treding@nvidia.com>
After a transfer timeout, some faulty I2C slave devices might hold down
the SDA pin. We can generate a bus clear command, hoping that the slave
might release the pins.
If the CLEAR command is not supported, we will use gpio recovery, if
available, to reset the bus.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The old email is still active, but for easier handling, I am going to
use my kernel.org address from now on. Also, add a mailmap for the now
defunct Pengutronix address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case of the I2C client exposes the flag I2C_CLIENT_HOST_NOTIFY,
pm_runtime_get_sync is called in order to always keep active the
adapter. However later on, pm_runtime_put_sync is never called
within the function in case of an error. This commit add this
error handling.
Fixes: 72bfcee11c ("i2c: Prevent runtime suspend of adapter when Host Notify is required")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix i2c_pxa_wait_bus_not_busy()'s boundary conditions, so that a
coincidental success and timeout results in the function returning
success.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Clean up decode_bits() to use pr_cont(), and move the newline into the
function rather than at its two callsites. Avoid printing an
unnecessary space before the newline.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The IRQ log output is supposed to appear on a single line. However,
commit 3a2dc1677b ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.
Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.
Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move the ID tables into one place, near the device dependent data.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move driver-private definitions out of the i2c-pxa.h platform data
header file into the driver itself. Nothing outside of the driver
makes use of these constants.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Always set the fm and hs members of struct pxa_reg_layout. These
members are already taking space, we don't need code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add definitions for the bits in the IBMR register, and use them in the
code. This improves readability.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arrange the register field definitions to be grouped together, rather
than the Armada-3700 definitions being separated from the rest of the
definitions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Re-arrange the PXA I2C code to avoid forward declarations, and keep
similar functionality (e.g. the non-IRQ mode support) together. This
improves code readability.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arrange the includes to be in alphabetical order to help avoid
duplicated includes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-pxa does not need linux/sched.h nor linux/time.h includes, so
remove these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-pxa was created before i2c_8bit_addr_from_msg() was implemented,
and used its own i2c_pxa_addr_byte() which is functionally the same.
Sadly, it was never updated to use this new helper. Switch it over.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In i2c_powermac_register_devices(), variable 'found_onyx' is bool and
assigned '0' and 'true' in different places. Use 'false' instead of '0'.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In AST2600 there have a slow peripheral bus between CPU and i2c
controller. Therefore GIC i2c interrupt status clear have delay timing,
when CPU issue write clear i2c controller interrupt status. To avoid
this issue, the driver need have read after write clear at i2c ISR.
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
Signed-off-by: ryan_chen <ryan_chen@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[wsa: added Fixes tag]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The problem is that we dereference "privdata->pci_dev" when we print
the error messages in amd_mp2_pci_init():
dev_err(ndev_dev(privdata), "Failed to enable MP2 PCI device\n");
^^^^^^^^^^^^^^^^^
Fixes: 529766e0a0 ("i2c: Add drivers for the AMD PCIe MP2 I2C controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We want to break with "i" set to zero whether we find the rate we want
or not. In the current code, if we don't find the rate we want then it
exits the loop with "i" set to -1 and results in an array underflow.
Fixes: 09cc9a3bce ("i2c: stm32f7: allows for any bus frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When slave status is I2C_SLAVE_RX_END, generate I2C_SLAVE_STOP
event to i2c_client.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for SMBUS quick command.
SMBUS quick command passes single bit of information to the
slave (target) device. Can be used to turn slave device on or off.
By default i2c_detect tool uses the smbus quick cmd to try and
detect devices. Without this support it will not detect some slaves.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use of_property_read_u32 to read the "reg" and "i2c-address" property
instead of using of_get_property to check the return values.
Signed-off-by: Aishwarya R <aishwaryarj100@gmail.com>
Tested-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The '>' expression itself is bool, no need to convert it to bool again.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If there is no interrupt defined then an error is logged due
to the use of platform_get_irq. The driver handles not having
the interrupt by falling back to polling, therefore make
the appropriate call when claiming it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not limitate to the 3 (100KHz, 400KHz, 1MHz) bus frequency but
instead allows any frequency (if it matches timing requirements).
Depending on the requested frequency, use the spec data from either
Standard, Fast or Fast Plus mode.
Hardcoding of min/max bus frequencies is removed and is instead computed.
The driver do not use anymore speed identifier but instead handle
directly the frequency and figure out the spec data (necessary
for the computation of the timing register) based on the frequency.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not print an error trace when deferring probe for some resource.
Fix as well the error message in case of tx dma_request_chan failure.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BCM2711, supported by ARCH_BCM2835, also has a controller by the
brcmstb driver so let's allow it to be compiled on that platform.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the slave eeprom has a "firmware-name" in devicetree, then pre-load
the data in the eeprom with this file. Otherwise we init the eeprom with
0xFF.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Björn Ardö <bjorn.ardo@axis.com>
[wsa: some cosmetic changes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rename DPM_FLAG_LEAVE_SUSPENDED to DPM_FLAG_MAY_SKIP_RESUME which
matches its purpose more closely.
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
it will print an error message by itself when platform_get_irq()
goes wrong. so don't need dev_err() in here again.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit adds I2C bus support for the Camera Control Interface
(CCI) I2C controller found on the Qualcomm SoC processors. This I2C
controller supports two masters and they are registered to the core.
CCI versions supported in the driver are msm8916, msm8996 and sdm845.
This is a rework of the patch posted by Vinod:
https://patchwork.kernel.org/patch/10569961/
With additional fixes + most of the comments addressed.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[wsa: removed err msg after platform_get_irq]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA transfer could be completed, but CPU (which handles DMA interrupt)
may get too busy and can't handle the interrupt in a timely manner,
despite of DMA IRQ being raised. In this case the DMA state needs to
synchronized before terminating DMA transfer in order not to miss the
DMA transfer completion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Boot CPU0 always handle I2C interrupt and under some rare circumstances
(like running KASAN + NFS root) it may stuck in uninterruptible state for
a significant time. In this case we will get timeout if I2C transfer is
running on a sibling CPU, despite of IRQ being raised. In order to handle
this rare condition, the IRQ status needs to be checked after completion
timeout.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added support for I2C slave functionality
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for High Speed Mode too.
The value for the parameters tSYMBOL and tLOW is taken from DesignWare
DW_apb_i2c Databook v2.01a, section 3.15.4.6. The calculation should
assume higher bus load since it gives slower timing parameter.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for Fast Mode Plus.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i801_add_mux() fills in the GPIO lookup table by manually populating an
array of gpiod_lookup structures. Use the existing GPIO_LOOKUP() helper
macro instead, to relax a dependency on the gpiod_lookup structure's
member names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When I wanted to print the chosen values to debug output, I concluded
that a helper function to parse one timing would be helpful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20. This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers. I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.
I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel. All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus. I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All in-tree users have been converted to the new i2c_new_scanned_device
function, so remove this deprecated one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
device_property_read_u32() returns errno or 0, so we should use the
integer variable 'ret' and not the u32 'val' to hold the retval.
Fixes: 0560ad5762 ("i2c: altera: Add Altera I2C Controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We already set DPM_FLAG_SMART_PREPARE, so we completely skip all
callbacks (other then prepare) where possible, quoting from
dw_i2c_plat_prepare():
/*
* If the ACPI companion device object is present for this device, it
* may be accessed during suspend and resume of other devices via I2C
* operation regions, so tell the PM core and middle layers to avoid
* skipping system suspend/resume callbacks for it in that case.
*/
return !has_acpi_companion(dev);
Also setting the DPM_FLAG_SMART_SUSPEND will cause acpi_subsys_suspend()
to leave the controller runtime-suspended even if dw_i2c_plat_prepare()
returned 0.
Leaving the controller runtime-suspended normally, when the I2C controller
is suspended during the suspend_late phase, is not an issue because
the pm_runtime_get_sync() done by i2c_dw_xfer() will (runtime-)resume it.
But for dw I2C controllers on Bay- and Cherry-Trail devices acpi_lpss.c
leaves the controller alive until the suspend_noirq phase, because it may
be used by the _PS3 ACPI methods of PCI devices and PCI devices are left
powered on until the suspend_noirq phase.
Between the suspend_late and resume_early phases runtime-pm is disabled.
So for any ACPI I2C OPRegion accesses done after the suspend_late phase,
the pm_runtime_get_sync() done by i2c_dw_xfer() is a no-op and the
controller is left runtime-suspended.
i2c_dw_xfer() has a check to catch this condition (rather then waiting
for the I2C transfer to timeout because the controller is suspended).
acpi_subsys_suspend() leaving the controller runtime-suspended in
combination with an ACPI I2C OPRegion access done after the suspend_late
phase triggers this check, leading to the following error being logged
on a Bay Trail based Lenovo Thinkpad 8 tablet:
[ 93.275882] i2c_designware 80860F41:00: Transfer while suspended
[ 93.275993] WARNING: CPU: 0 PID: 412 at drivers/i2c/busses/i2c-designware-master.c:429 i2c_dw_xfer+0x239/0x280
...
[ 93.276252] Workqueue: kacpi_notify acpi_os_execute_deferred
[ 93.276267] RIP: 0010:i2c_dw_xfer+0x239/0x280
...
[ 93.276340] Call Trace:
[ 93.276366] __i2c_transfer+0x121/0x520
[ 93.276379] i2c_transfer+0x4c/0x100
[ 93.276392] i2c_acpi_space_handler+0x219/0x510
[ 93.276408] ? up+0x40/0x60
[ 93.276419] ? i2c_acpi_notify+0x130/0x130
[ 93.276433] acpi_ev_address_space_dispatch+0x1e1/0x252
...
So since on BYT and CHT platforms we want ACPI I2c OPRegion accesses
to work until the suspend_noirq phase, we need the controller to be
runtime-resumed during the suspend phase if it is runtime-suspended
suspended at that time. This means that we must not set the
DPM_FLAG_SMART_SUSPEND on these platforms.
On BYT and CHT we already have a special ACCESS_NO_IRQ_SUSPEND flag
to make sure the controller stays functional until the suspend_noirq
phase. This commit makes the driver not set the DPM_FLAG_SMART_SUSPEND
flag when that flag is set.
Cc: stable@vger.kernel.org
Fixes: b30f2f6556 ("i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has:
- using defines for bus speeds to avoid mistakes in hardcoded values;
lots of small driver updates because of that. Thanks, Andy!
- API change: i2c_setup_smbus_alert() was renamed to
i2c_new_smbus_alert_device() and returns ERRPTR now. All in-tree
users have been converted
- in the core, a rare race condition when deleting the cdev has been
fixed. Thanks, Kevin!
- lots of driver updates. Thanks, everyone!
I also want to mention: The amount of review and testing tags given
was quite high this time. Thank you to these people, too. I hope we
can keep it like this!"
* 'i2c/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: rcar: clean up after refactoring i2c_timings
macintosh: convert to i2c_new_scanned_device
i2c: drivers: Use generic definitions for bus frequencies
i2c: algo: Use generic definitions for bus frequencies
i2c: stm32f7: switch to I²C generic property parsing
i2c: rcar: Consolidate timings calls in rcar_i2c_clock_calculate()
i2c: core: Allow override timing properties with 0
i2c: core: Provide generic definitions for bus frequencies
i2c: mxs: Use dma_request_chan() instead dma_request_slave_channel()
i2c: imx: remove duplicate print after platform_get_irq()
i2c: designware: Fix spelling typos in the comments
i2c: designware: Discard i2c_dw_read_comp_param() function
i2c: designware: Detect the FIFO size in the common code
i2c: dev: Fix the race between the release of i2c_dev and cdev
i2c: qcom-geni: Drop of_platform.h include
i2c: qcom-geni: Grow a dev pointer to simplify code
i2c: qcom-geni: Let firmware specify irq trigger flags
i2c: stm32f7: do not backup read-only PECR register
i2c: smbus: remove outdated references to irq level triggers
i2c: convert SMBus alert setup function to return an ERRPTR
...
The pointer is not really needed anymore since we have the timings
struct available in the function itself now. Remove the pointer and
access the struct directly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The interrupt is not required so use platform_irq_get_optional() to
avoid error messages like
i2c-pca-platform 22080000.i2c: IRQ index 0 not found
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nvidia card may come with a "phantom" UCSI device, and its driver gets
stuck in probe routine, prevents any system PM operations like suspend.
There's an unaccounted case that the target time can equal to jiffies in
gpu_i2c_check_status(), let's solve that by using readl_poll_timeout()
instead of jiffies comparison functions.
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ajay Gupta <ajayg@nvidia.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since we have generic definitions for bus frequencies, let's use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions: i2c_parse_fw_timings().
While here, replace hard coded values with standard bus frequency definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move i2c_parse_fw_timings() to rcar_i2c_clock_calculate() to consolidate
timings calls in one place.
While here, replace hard coded values with standard bus frequency definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some drivers may allow to override properties with 0 value when defaults
are not in use, thus, replace memset() with corresponding per property
update.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are few maximum bus frequencies being used in the I²C core code.
Provide generic definitions for bus frequencies and use them in the core.
The drivers may use predefined constants where it is appropriate.
Some of them are already using these under slightly different names.
We will convert them later to use newly introduced defines.
Note, the name of modes are chosen to follow well established naming
scheme [1].
These definitions will also help to avoid typos in the numbers that
may lead to subtle errors.
[1]: https://en.wikipedia.org/wiki/I%C2%B2C#Differences_between_modes
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver forgets to disable and unprepare clk when remove.
Add a call to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We don't need dev_err() message because when something goes wrong,
platform_get_irq() has print an error message itself, so we should
remove duplicate dev_err().
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix spelling typos in the comments with help of `codespell`.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no code left in the kernel which would be using the function.
So just remove it.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The problem with detecting the FIFO depth in the platform driver
is that in order to implement this we have to access the controller
IC_COMP_PARAM_1 register. Currently it's done before the
i2c_dw_set_reg_access() method execution, which is errors prone since
the method determines the registers endianness and access mode and we
can't use dw_readl/dw_writel accessors before this information is
retrieved. We also can't move the i2c_dw_set_reg_access() function
invocation to after the master/slave probe functions call (when endianness
and access mode are determined), since the FIFO depth information is used
by them for initializations. So in order to fix the problem we have no
choice but to move the FIFO size detection methods to the common code and
call it at the probe stage.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The struct cdev is embedded in the struct i2c_dev. In the current code,
we would free the i2c_dev struct directly in put_i2c_dev(), but the
cdev is manged by a kobject, and the release of it is not predictable.
So it is very possible that the i2c_dev is freed before the cdev is
entirely released. We can easily get the following call trace with
CONFIG_DEBUG_KOBJECT_RELEASE and CONFIG_DEBUG_OBJECTS_TIMERS enabled.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38
WARNING: CPU: 19 PID: 1 at lib/debugobjects.c:325 debug_print_object+0xb0/0xf0
Modules linked in:
CPU: 19 PID: 1 Comm: swapper/0 Tainted: G W 5.2.20-yocto-standard+ #120
Hardware name: Marvell OcteonTX CN96XX board (DT)
pstate: 80c00089 (Nzcv daIf +PAN +UAO)
pc : debug_print_object+0xb0/0xf0
lr : debug_print_object+0xb0/0xf0
sp : ffff00001292f7d0
x29: ffff00001292f7d0 x28: ffff800b82151788
x27: 0000000000000001 x26: ffff800b892c0000
x25: ffff0000124a2558 x24: 0000000000000000
x23: ffff00001107a1d8 x22: ffff0000116b5088
x21: ffff800bdc6afca8 x20: ffff000012471ae8
x19: ffff00001168f2c8 x18: 0000000000000010
x17: 00000000fd6f304b x16: 00000000ee79de43
x15: ffff800bc0e80568 x14: 79616c6564203a74
x13: 6e6968207473696c x12: 5f72656d6974203a
x11: ffff0000113f0018 x10: 0000000000000000
x9 : 000000000000001f x8 : 0000000000000000
x7 : ffff0000101294cc x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 00000000ffffffff x2 : 0000000000000000
x1 : 387fc15c8ec0f200 x0 : 0000000000000000
Call trace:
debug_print_object+0xb0/0xf0
__debug_check_no_obj_freed+0x19c/0x228
debug_check_no_obj_freed+0x1c/0x28
kfree+0x250/0x440
put_i2c_dev+0x68/0x78
i2cdev_detach_adapter+0x60/0xc8
i2cdev_notifier_call+0x3c/0x70
notifier_call_chain+0x8c/0xe8
blocking_notifier_call_chain+0x64/0x88
device_del+0x74/0x380
device_unregister+0x54/0x78
i2c_del_adapter+0x278/0x2d0
unittest_i2c_bus_remove+0x3c/0x80
platform_drv_remove+0x30/0x50
device_release_driver_internal+0xf4/0x1c0
driver_detach+0x58/0xa0
bus_remove_driver+0x84/0xd8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
of_unittest_overlay+0x8d4/0xbe0
of_unittest+0xae8/0xb3c
do_one_initcall+0xac/0x450
do_initcall_level+0x208/0x224
kernel_init_freeable+0x2d8/0x36c
kernel_init+0x18/0x108
ret_from_fork+0x10/0x1c
irq event stamp: 3934661
hardirqs last enabled at (3934661): [<ffff00001009fa04>] debug_exception_exit+0x4c/0x58
hardirqs last disabled at (3934660): [<ffff00001009fb14>] debug_exception_enter+0xa4/0xe0
softirqs last enabled at (3934654): [<ffff000010081d94>] __do_softirq+0x46c/0x628
softirqs last disabled at (3934649): [<ffff0000100b4a1c>] irq_exit+0x104/0x118
This is a common issue when using cdev embedded in a struct.
Fortunately, we already have a mechanism to solve this kind of issue.
Please see commit 233ed09d7f ("chardev: add helper function to
register char devs with a struct device") for more detail.
In this patch, we choose to embed the struct device into the i2c_dev,
and use the API provided by the commit 233ed09d7f to make sure that
the release of i2c_dev and cdev are in sequence.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver doesn't call any DT platform functions like of_platform_*().
Remove the include as it isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some lines are long here. Use a struct dev pointer to shorten lines and
simplify code. The clk_get() call can fail because of EPROBE_DEFER
problems too, so just remove the error print message because it isn't
useful. Finally, platform_get_irq() already prints an error so just
remove that error message.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to force IRQF_TRIGGER_HIGH here as the DT or ACPI tables
should take care of this for us. Just use 0 instead so that we use the
flags from the firmware. Also, remove specify dev_name() for the irq
name so that we can get better information in /proc/interrupts about
which device is generating interrupts.
Cc: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The PECR register provides received packet computed PEC value.
It makes no sense restoring its value after a reset, and anyway,
as read-only register it cannot be restored.
Fixes: ea6dd25dee ("i2c: stm32f7: add PM_SLEEP suspend/resume support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_verify_client() can fail, so we need to put the device when that
happens.
Fixes: 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure notifications")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a GPIO we are trying to use is not available and we are deferring
the probe, don't output an error message.
This seems to have been the intent of commit 05c7477885
("i2c: gpio: Add support for named gpios in DT") but the error was
still output due to not checking the updated 'retdesc'.
Fixes: 05c7477885 ("i2c: gpio: Add support for named gpios in DT")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IRQ levels are now handled within the IRQ core. Remove the forgotten
references from the documentation.
Fixes: 9b9f2b8bc2 ("i2c: i2c-smbus: Use threaded irq for smbalert")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Only few drivers use this call, so drivers and I2C core are converted at
once with this patch. By simply using i2c_new_client_device() instead of
i2c_new_device(), we easily can return an ERRPTR for this function as
well. To make out of tree users aware that something changed, the
function is renamed to i2c_new_smbus_alert_device().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a new stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Defer the initial enabling of the Fast Mode Plus bits after the
stm32f7_i2c_setup_timing call in probe function in order to avoid
enabling them if speed is downgraded.
Clear & restore the Fast Mode Plus bits in the suspend/resume
handlers of the driver.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HDMI blocks in the BCM2771 have an i2c controller to retrieve the
EDID. This block is split into two parts, the BSC and the AUTO_I2C,
lying in two separate register areas.
The AUTO_I2C block has a mailbox-like interface and will take away the
BSC control from the CPU if enabled. However, the BSC is the actually
the same controller than the one supported by the brcmstb driver, and
the AUTO_I2C doesn't really bring any immediate benefit.
Let's use the BSC then, but let's also tie the AUTO_I2C registers with a
separate compatible so that we can enable AUTO_I2C if needed in the
future.
The AUTO_I2C is enabled by default at boot though, so we first need to
release the BSC from the AUTO_I2C control.
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a new API devm_platform_ioremap_resource() to simplify code.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Tested-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Function i2c_dw_pci_remove() -> pci_free_irq_vectors() ->
pci_disable_msi() -> free_msi_irqs() will throw a BUG_ON() for MSI
enabled device since the driver has not released the requested IRQ before
calling the pci_free_irq_vectors().
Here driver requests an IRQ using devm_request_irq() but automatic
release happens only after remove callback. Fix this by explicitly
freeing the IRQ before calling pci_free_irq_vectors().
Fixes: 21aa3983d6 ("i2c: designware-pci: Switch over to MSI interrupts")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Martin noticed that nct6775 driver does not load properly on his system
in v5.4+ kernels. The issue was bisected to commit b84398d6d7 ("i2c:
i801: Use iTCO version 6 in Cannon Lake PCH and beyond") but it is
likely not the culprit because the faulty code has been in the driver
already since commit 9424693035 ("i2c: i801: Create iTCO device on
newer Intel PCHs"). So more likely some commit that added PCI IDs of
recent chipsets made the driver to create the iTCO_wdt device on Martins
system.
The issue was debugged to be PCI configuration access to the PMC device
that is not present. This returns all 1's when read and this caused the
iTCO_wdt driver to accidentally request resourses used by nct6775.
It turns out that the SMI resource is only required for some ancient
systems, not the ones supported by this driver. For this reason do not
populate the SMI resource at all and drop all the related code. The
driver now always populates the main I/O resource and only in case of SPT
(Intel Sunrisepoint) compatible devices it adds another resource for the
NO_REBOOT bit. These two resources are of different types so
platform_get_resource() used by the iTCO_wdt driver continues to find
the both resources at index 0.
Link: https://lore.kernel.org/linux-hwmon/CAM1AHpQ4196tyD=HhBu-2donSsuogabkfP03v1YF26Q7_BgvgA@mail.gmail.com/
Fixes: 9424693035 ("i2c: i801: Create iTCO device on newer Intel PCHs")
[wsa: complete fix needs all of http://patchwork.ozlabs.org/project/linux-i2c/list/?series=160959&state=*]
Reported-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The comment had some flaws which are now fixed:
- the prefix is 'MAC' not 'AAPL'
- no kernel coding style and too short length
- 'we do' instead of 'we to'
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the i2c-stm32f7 controller to become a wakeup-source
of the system. In such case, when a slave is registered to the
I2C controller, receiving a I2C message targeting that registered
slave address wakes up the suspended system.
In order to be able to wake-up, the I2C controller DT node
must have the property wakeup-source defined and a slave
must be registered.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rework the read and write code paths in the driver to support operation
in atomic contexts. To achieve this, the driver must not rely on IRQs
and not call schedule(), e.g. via a sleep routine, in these cases.
With this patch the driver supports normal operation, DMA transfers and
now the polling mode or also called sleep-free or IRQ-less operation. It
makes the code not simpler or easier to read, but atomic I2C transfers
are needed on some hardware configurations, e.g. to trigger reboots on
an external PMIC chip.
Signed-off-by: Stefan Lengfeld <contact@stefanchrist.eu>
[m.felsch@pengutronix.de: integrate https://patchwork.ozlabs.org/patch/1085943/ review feedback]
[m.felsch@pengutronix.de: adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement i2c bus recovery when slaves devices might hold SDA low.
In this case re-assign SCL/SDA to gpios and issue 9 dummy clock pulses
until the slave release SDA.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Factor out 100 from the equation and do 32-bit arithmetic (3 * clk_mhz / 10)
instead of 64-bit.
Notice that clk_mhz is MHz, so the multiplication will never wrap 32 bits
and there is no need for div_u64().
Addresses-Coverity: 1458369 ("Unintentional integer overflow")
Fixes: 0560ad5762 ("i2c: altera: Add Altera I2C Controller driver")
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The printout for txabrt is way too talkative and is highly annoying with
scanning programs like 'i2cdetect'. Reduce it to the minimum, the rest
can be gained by I2C core debugging and datasheet information. Also,
make it a debug printout, it won't help the regular user.
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"i2c core:
- huge improvements and refactorizations of the Linux I2C
documentation (lots of thanks to Luca for doing it and Jean for the
careful review)
- subsystem wide API conversion to i2c_new_client_device()
- remove obsolete parport-light driver
- smaller core updates (removal of 'extern', enabling more compile
testing, use more helper macros)
- and quite a bunch of driver updates (new IDs, simplifications,
better PM, support of atomic transfers and other improvements)
i2c-mux:
- The main feature is the idle-state rework of the pca954x driver
from Biwen Li
at24 driver:
- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25
bindings
- add support for regulator and pm_runtime control"
* 'i2c/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (91 commits)
i2c: cros-ec-tunnel: Fix ACPI identifier
i2c: cros-ec-tunnel: Fix slave device enumeration
i2c: stm32f7: add PM_SLEEP suspend/resume support
i2c: cadence: Fix wording in i2c-cadence driver
i2c: cadence: Fix power management order of operations
i2c: cadence: Fix error printing in case of defer
i2c: cadence: Handle transfer_size rollover
i2c: i801: Add support for Intel Comet Lake PCH-V
docs: i2c: writing-clients: properly name the stop condition
docs: i2c: i2c-protocol: use same wording as smbus-protocol
docs: i2c: rename sections so the overall picture is clearer
docs: i2c: old-module-parameters: use monospace instead of ""
docs: i2c: old-module-parameters: clarify this is for obsolete kernels
docs: i2c: old-module-parameters: fix internal hyperlink
docs: i2c: instantiating-devices: use monospace for sysfs attributes
docs: i2c: instantiating-devices: rearrange static instatiation
docs: i2c: instantiating-devices: fix internal hyperlink
docs: i2c: smbus-protocol: improve I2C Block transactions description
docs: i2c: smbus-protocol: fix punctuation
docs: i2c: smbus-protocol: fix typo
...
Add Hisilicon Hip08-Lite I2C controller clock frequency support
to the ACPI driver for AMD SoCs (APD) and to the Designware I2C
driver (Hanjun Guo).
-----BEGIN PGP SIGNATURE-----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=9BkB
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add Hisilicon Hip08-Lite I2C controller clock frequency support to the
ACPI driver for AMD SoCs (APD) and to the Designware I2C driver
(Hanjun Guo)"
* tag 'acpi-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
i2c: designware: Add ACPI HID for Hisilicon Hip08-Lite I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip08-Lite I2C controller
Add ACPI HID HISI02A3 for Hisilicon Hip08 Lite, which has different
clock frequency from Hip08 for I2C controller.
Tested-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The initial patch was using the incorrect identifier.
Fixes: 9af1563a54 ("i2c: cros-ec-tunnel: Make the device acpi compatible")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During adding of the adapter the slave device registration
use to fail as the acpi companion field was not populated.
Fixes: 9af1563a54 ("i2c: cros-ec-tunnel: Make the device acpi compatible")
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Backup/restore I2C registers as part of the suspend/resume
handlers. The device is marked as suspended to ensure that
transfers are rejected during the suspended period.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix wording based on checkpatch.pl
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
E.g. pm_runtime_set_active must be called while the power
management system is disabled. Fixes extra hanging clk_enable.
Signed-off-by: Topi Kuutela <topi.kuutela@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not print error in case of EPROBE_DEFER.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Under certain conditions, Cadence's I2C controller's transfer_size
register will roll over and generate invalid read transactions. Before
this change, the ISR relied solely on the RXDV bit to determine when to
write more data to the user's buffer. The invalid read data would cause
overruns, smashing stacks and worse.
This change stops the buffer writes to the requested boundary and
reports the error. The controller will be reset so normal transactions
may resume.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> # in a seperate mail
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for Intel Comet Lake PCH-V which is based on Intel Kaby
Lake. Difference between it and other Comet Lake variants is that former
uses previous iTCO version 4 and latter use version 6 like Intel Cannon
Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a statement that is indented one level too deeply, remove
the extraneous tab.
Fixes: b4c119dbc3 ("i2c: xiic: Add timeout to the rx fifo wait loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a spelling mistake in a module parameter description.
Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Update the help text to reflect current support devices:
1. The Exynos high speed I2C driver supports Exynos5 (ARMv7), Exynos5433
and Exynos7 (both ARMv8) SoCs,
2. The S3C I2C driver supports S3C, S5Pv210 and Exynos{3,4,5} SoCs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some of the I2C bus drivers can be compile tested to increase build
coverage. This requires also:
1. Adding dependencies on COMMON_CLK for BCM2835 and Meson I2C
controllers,
2. Adding 'if' conditional to 'default y' so they will not get enabled
by default on all other architectures,
3. Limiting few compile test options to supported architectures (which
provide the readsX()/writesX() primitives).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[wsa: revert chunk for ZX2967. it needs more preparation]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The recommendation is that the set_active should be done
with pm runtime disabled.
Also fix the remove path for clocking.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It's not always the case that clock is already available when i2c
driver get probed at the first time, e.g. the clock is provided by
clock wizard which may be probed after i2c driver. So let's defer
the probe when devm_clk_get() call fails and give it chance to
try later.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add timeout to the rx fifo empty wait loop. Also check for the return
value for xiic_reinit and pass it to xiic_start_xfer.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
size_t should be printed with its own format to be 64-bit friendly and
fix warning when compiling on 64-bit platform (e.g. with COMPILE_TEST):
drivers/i2c/busses/i2c-highlander.c: In function ‘highlander_i2c_smbus_xfer’:
drivers/i2c/busses/i2c-highlander.c:325:22: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pnx.c: In function ‘i2c_pnx_probe’:
drivers/i2c/busses/i2c-pnx.c:737:47: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 5 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pmcmsp.c: In function ‘pmcmsptwi_probe’:
drivers/i2c/busses/i2c-pmcmsp.c:276:25: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 3 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang