Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- a cleanup series to get rid of mindlessly copied code.
- another bunch of new pointlessly different interrupt chip drivers.
Adding homebrewn irq chips (and timers) to SoCs must provide a
value add which is beyond the imagination of mere mortals.
- the usual SoC irq controller updates, IOW my second cat herding
project"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
irqchip: gic-v3: Implement CPU PM notifier
irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling
irqchip: renesas-intc-irqpin: Add minimal runtime PM support
irqchip: renesas-intc-irqpin: Add helper variable dev = &pdev->dev
irqchip: atmel-aic5: Add sama5d4 support
irqchip: atmel-aic5: The sama5d3 has 48 IRQs
Documentation: bcm7120-l2: Add Broadcom BCM7120-style L2 binding
irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller
irqchip: renesas-irqc: Add binding docs for new R-Car Gen2 SoCs
irqchip: renesas-irqc: Add DT binding documentation
irqchip: renesas-intc-irqpin: Document SoC-specific bindings
openrisc: Get rid of handle_IRQ
arm64: Get rid of handle_IRQ
ARM: omap2: irq: Convert to handle_domain_irq
ARM: imx: tzic: Convert to handle_domain_irq
ARM: imx: avic: Convert to handle_domain_irq
irqchip: or1k-pic: Convert to handle_domain_irq
irqchip: atmel-aic5: Convert to handle_domain_irq
irqchip: atmel-aic: Convert to handle_domain_irq
irqchip: gic-v3: Convert to handle_domain_irq
...
* pm-genirq:
PM / genirq: Document rules related to system suspend and interrupts
PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle
x86 / PM: Set IRQCHIP_SKIP_SET_WAKE for IOAPIC IRQ chip objects
genirq: Simplify wakeup mechanism
genirq: Mark wakeup sources as armed on suspend
genirq: Create helper for flow handler entry check
genirq: Distangle edge handler entry
genirq: Avoid double loop on suspend
genirq: Move MASK_ON_SUSPEND handling into suspend_device_irqs()
genirq: Make use of pm misfeature accounting
genirq: Add sanity checks for PM options on shared interrupt lines
genirq: Move suspend/resume logic into irq/pm code
PM / sleep: Mechanism for aborting system suspends unconditionally
Calling irq_find_mapping from outside a irq_{enter,exit} section is
unsafe and produces ugly messages if CONFIG_PROVE_RCU is enabled:
If coming from the idle state, the rcu_read_lock call in irq_find_mapping
will generate an unpleasant warning:
<quote>
===============================
[ INFO: suspicious RCU usage. ]
3.16.0-rc1+ #135 Not tainted
-------------------------------
include/linux/rcupdate.h:871 rcu_read_lock() used illegally while idle!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: (rcu_read_lock){......}, at: [<ffffffc00010206c>]
irq_find_mapping+0x4c/0x198
</quote>
As this issue is fairly widespread and involves at least three
different architectures, a possible solution is to add a new
handle_domain_irq entry point into the generic IRQ code that
the interrupt controller code can call.
This new function takes an irq_domain, and calls into irq_find_domain
inside the irq_{enter,exit} block. An additional "lookup" parameter is
used to allow non-domain architecture code to be replaced by this as well.
Interrupt controllers can then be updated to use the new mechanism.
This code is sitting behind a new CONFIG_HANDLE_DOMAIN_IRQ, as not all
architectures implement set_irq_regs (yes, mn10300, I'm looking at you...).
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1409047421-27649-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently we suspend wakeup interrupts by lazy disabling them and
check later whether the interrupt has fired, but that's not sufficient
for suspend to idle as there is no way to check that once we
transitioned into the CPU idle state.
So we change the mechanism in the following way:
1) Leave the wakeup interrupts enabled across suspend
2) Add a check to irq_may_run() which is called at the beginning of
each flow handler whether the interrupt is an armed wakeup source.
This check is basically free as it just extends the existing check
for IRQD_IRQ_INPROGRESS. So no new conditional in the hot path.
If the IRQD_WAKEUP_ARMED flag is set, then the interrupt is
disabled, marked as pending/suspended and the pm core is notified
about the wakeup event.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ rjw: syscore.c and put irq_pm_check_wakeup() into pm.c ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This allows us to utilize this information in the irq_may_run() check
without adding another conditional to the fast path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All flow handlers - except the per cpu ones - check for an interrupt
in progress and an eventual concurrent polling on another cpu.
Create a helper function for the repeated code pattern.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the interrupt is disabled or has no action, then we should not call
the poll check. Separate the checks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can synchronize the suspended interrupts right away. No need for an
extra loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no reason why we should delay the masking of interrupts whose
interrupt chip requests MASK_ON_SUSPEND to the point where we check
the wakeup interrupts. We can do it right at the point where we mark
the interrupt as suspended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the accounting fields which got introduced for snity checking for
the various PM options.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Account the IRQF_NO_SUSPEND and IRQF_RESUME_EARLY actions on shared
interrupt lines and yell loudly if there is a mismatch.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No functional change. Preparatory patch for cleaning up the suspend
abort functionality. Update the comments while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It should be request_threaded_irq, not request_irq
[jkosina@suse.cz: not that it would matter, as both have the same
set of arguments anyway, but for sake of consistency ...]
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[ARM specific]
These are generally replaced with raw_cpu_ptr. However, in
gic_get_percpu_base() we immediately dereference the pointer. This is
equivalent to a raw_cpu_read. So use that operation there.
Cc: nicolas.pitre@linaro.org
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Export handle_fasteoi_irq to be able to use it in e.g. the Zynq gpio driver
since commit 6dd8595083 ("gpio: zynq: Fix IRQ handlers").
This fixes the following link issue:
ERROR: "handle_fasteoi_irq" [drivers/gpio/gpio-zynq.ko] undefined!
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Vincent Stehle <vincent.stehle@laposte.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/1408663880-29179-1-git-send-email-vincent.stehle@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull irq updates from Thomas Gleixner:
"Nothing spectacular from the irq department this time:
- overhaul of the crossbar chip driver
- overhaul of the spear shirq chip driver
- support for the atmel-aic chip
- code move from arch to drivers
- the usual tiny fixlets
- two reverts worth to mention which undo the too simple attempt of
supporting wakeup interrupts on shared interrupt lines"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
Revert "irq: Warn when shared interrupts do not match on NO_SUSPEND"
Revert "PM / sleep / irq: Do not suspend wakeup interrupts"
irq: Warn when shared interrupts do not match on NO_SUSPEND
irqchip: atmel-aic: Define irq fixups for atmel SoCs
irqchip: atmel-aic: Implement RTC irq fixup
irqchip: atmel-aic: Add irq fixup infrastructure
irqchip: atmel-aic: Add atmel AIC/AIC5 drivers
irqchip: atmel-aic: Move binding doc to interrupt-controller directory
genirq: generic chip: Export irq_map_generic_chip function
PM / sleep / irq: Do not suspend wakeup interrupts
irqchip: or1k-pic: Migrate from arch/openrisc/
irqchip: crossbar: Allow for quirky hardware with direct hardwiring of GIC
documentation: dt: omap: crossbar: Add description for interrupt consumer
irqchip: crossbar: Introduce centralized check for crossbar write
irqchip: crossbar: Introduce ti, max-crossbar-sources to identify valid crossbar mapping
irqchip: crossbar: Add kerneldoc for crossbar_domain_unmap callback
irqchip: crossbar: Set cb pointer to null in case of error
irqchip: crossbar: Change the goto naming
irqchip: crossbar: Return proper error value
irqchip: crossbar: Fix kerneldoc warning
...
This reverts commit 4fae4e7624.
Undo because it breaks working systems.
Requested-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit d709f7bcbb.
Undo, because it might break exisiting functionality.
Requested-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When suspend_device_irqs() iterates all descriptors, its pointless if
one has NO_SUSPEND set while another has not.
Validate on request_irq() that NO_SUSPEND state maches for SHARED
interrupts.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/20140724133921.GY6758@twins.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export the generic irq map function in order to provide irq_domain ops with
generic mapping and specific of xlate function (needed by the new atmel
AIC driver).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1405012462-766-2-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
If an IRQ has been configured for wakeup via enable_irq_wake(), the
driver who has done that must be prepared for receiving interrupts
after suspend_device_irqs() has returned, so there is no need to
"suspend" such IRQs. Moreover, if drivers using enable_irq_wake()
actually want to receive interrupts after suspend_device_irqs() has
returned, they need to add IRQF_NO_SUSPEND to the IRQ flags while
requesting the IRQs, which shouldn't be necessary (it also goes a bit
too far, as IRQF_NO_SUSPEND causes the IRQ to be ignored by
suspend_device_irqs() all the time regardless of whether or not it
has been configured for signaling wakeup).
For the above reasons, make __disable_irq() ignore IRQ descriptors
with IRQD_WAKEUP_STATE set when its suspend argument is true which
effectively causes them to behave like IRQs with IRQF_NO_SUSPEND
set.
This also allows IRQs configured for wakeup via enable_irq_wake()
to work as wakeup interrupts for the "freeze" (suspend-to-idle)
sleep mode automatically just like for any other sleep states.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Li Aubrey <aubrey.li@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Link: http://lkml.kernel.org/r/4679574.kGUnqAuNl9@vostro.rjw.lan
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_free_hwirqs() always calls irq_free_descs() with a cnt == 0
which makes it a no-op since the interrupt count to free is
decremented in itself.
Fixes: 7b6ef12625
Signed-off-by: Keith Busch <keith.busch@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1404167084-8070-1-git-send-email-keith.busch@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export irq_domain_disassociate() to architecture interrupt drivers,
so it could be used to handle legacy IRQ descriptors on x86.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1402302011-23642-37-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No more users. Get rid of the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140507154341.012847637@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Create a new interface and confine it with a config switch which makes
clear that this is just legacy support and not to be used for new code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140507154340.574437049@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No more users. And it's not going to come back. If you need
hotplugable irq chips, use irq domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-and-acked-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140507154340.302183048@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We want to get rid of the public interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140507154340.061990194@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Not really the solution to the problem, but at least it confines the
mess in the core code and allows to get rid of the create/destroy_irq
variants from hell, i.e. 3 implementations with different semantics
plus the x86 specific variants __create_irqs and create_irq_nr
which have been invented in another circle of hell.
x86 : x86 should be converted to irq domains and I'm deliberately
making it impossible to do the multi-vector MSI support by
adding more crap to the current mess. It's not that hard to do
and I'm really tired of the trainwrecks which have been invented
by baindaid engineering so far. Any attempt to do multi-vector
MSI or ioapic hotplug without converting to irq domains is NAKed
hereby.
tile: Might use irq domains as well, but it has a very limited
interrupt space, so handling it via this functionality might be
the right thing to do even in the long run.
ia64: That's an hopeless case, as I doubt that anyone has the stomach
to rewrite the homebrewn dynamic allocation facilities. I stared
at it for a couple of hours and gave up. The create/destroy_irq
mess could be made private to itanic right away if there
wouldn't be the iommu/dmar driver being shared with x86. So to
do that I'm going to add a separate ia64 specific implementation
later in order not to deep-six itanic right away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20140507154334.208629358@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Till reported that the spurious interrupt detection of threaded
interrupts is broken in two ways:
- note_interrupt() is called for each action thread of a shared
interrupt line. That's wrong as we are only interested whether none
of the device drivers felt responsible for the interrupt, but by
calling multiple times for a single interrupt line we account
IRQ_NONE even if one of the drivers felt responsible.
- note_interrupt() when called from the thread handler is not
serialized. That leaves the members of irq_desc which are used for
the spurious detection unprotected.
To solve this we need to defer the spurious detection of a threaded
interrupt to the next hardware interrupt context where we have
implicit serialization.
If note_interrupt is called with action_ret == IRQ_WAKE_THREAD, we
check whether the previous interrupt requested a deferred check. If
not, we request a deferred check for the next hardware interrupt and
return.
If set, we check whether one of the interrupt threads signaled
success. Depending on this information we feed the result into the
spurious detector.
If one primary handler of a shared interrupt returns IRQ_HANDLED we
disable the deferred check of irq threads on the same line, as we have
found at least one device driver who cared.
Reported-by: Till Straumann <strauman@slac.stanford.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1303071450130.22263@ionos
On x86 the allocation of irq descriptors may allocate interrupts which
are in the range of the GSI interrupts. That's wrong as those
interrupts are hardwired and we don't have the irq domain translation
like PPC. So one of these interrupts can be hooked up later to one of
the devices which are hard wired to it and the io_apic init code for
that particular interrupt line happily reuses that descriptor with a
completely different configuration so hell breaks lose.
Inside x86 we allocate dynamic interrupts from above nr_gsi_irqs,
except for a few usage sites which have not yet blown up in our face
for whatever reason. But for drivers which need an irq range, like the
GPIO drivers, we have no limit in place and we don't want to expose
such a detail to a driver.
To cure this introduce a function which an architecture can implement
to impose a lower bound on the dynamic interrupt allocations.
Implement it for x86 and set the lower bound to nr_gsi_irqs, which is
the end of the hardwired interrupt space, so all dynamic allocations
happen above.
That not only allows the GPIO driver to work sanely, it also protects
the bogus callsites of create_irq_nr() in hpet, uv, irq_remapping and
htirq code. They need to be cleaned up as well, but that's a separate
issue.
Reported-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Krogerus Heikki <heikki.krogerus@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1404241617360.28206@ionos.tec.linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current implementation of irq_set_affinity() refuses rightfully to
route an interrupt to an offline cpu.
But there is a special case, where this is actually desired. Some of
the ARM SoCs have per cpu timers which require setting the affinity
during cpu startup where the cpu is not yet in the online mask.
If we can't do that, then the local timer interrupt for the about to
become online cpu is routed to some random online cpu.
The developers of the affected machines tried to work around that
issue, but that results in a massive mess in that timer code.
We have a yet unused argument in the set_affinity callbacks of the irq
chips, which I added back then for a similar reason. It was never
required so it got not used. But I'm happy that I never removed it.
That allows us to implement a sane handling of the above scenario. So
the affected SoC drivers can add the required force handling to their
interrupt chip, switch the timer code to irq_force_affinity() and
things just work.
This does not affect any existing user of irq_set_affinity().
Tagged for stable to allow a simple fix of the affected SoC clock
event drivers.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143315.717251504@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This will allow to use the dummy IRQ handler no_action() from drivers
compiled as module. Drivers which use ARM FIQ interrupts can use this
to request the interrupt via the normal request_irq() mechanism w/o
having to copy the dummy handler to their own code.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Link: http://lkml.kernel.org/r/1395476431-16070-1-git-send-email-shc_work@mail.ru
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Includes:
- /proc/irq/default_smp_affinity
- /proc/irq/*/affinity_hint
- /proc/irq/*/smp_affinity
- /proc/irq/*/smp_affinity_list
Users can distill the same information by reading /proc/interrupts.
Signed-off-by: Chema Gonzalez <chema@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Link: http://lkml.kernel.org/r/1394765455-1217-1-git-send-email-chema@google.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The flag is necessary for interrupt chips which require an ACK/EOI
after the handler has run. In case of threaded handlers this needs to
happen after the threaded handler has completed before the unmask of
the interrupt.
The flag is only unseful in combination with the handle_fasteoi_irq
flow control handler.
It can be combined with the flag IRQCHIP_EOI_IF_HANDLED, so the EOI is
not issued when the interrupt is disabled or in progress.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/1394733834-26839-2-git-send-email-hdegoede@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For certain irq types, e.g. gpios, it's necessary to request resources
before starting up the irq.
This might fail so we cannot use the irq_startup() callback because we
might call the irq_set_type() callback before that which does not make
sense when the resource is not available. Calling irq_startup() before
irq_set_type() can lead to spurious interrupts which is not desired
either.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1403080857160.18573@ionos.tec.linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No more users outside the core code. Put it into the poison
cabinet. That also gets rid of the linux/irq.h include in
kernel_stat.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140223212739.124207133@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is a common pattern all over the place:
kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
This results in a call to core code anyway. So provide a function
which does the same thing in core.
While at it, replace the butt ugly macro with an inline.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140223212737.422068876@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Include appropriate header file include/linux/of_irq.h in
kernel/irq/irqdomain.c because it contains prototype definition of
function define in kernel/irq/irqdomain.c.
This eliminates the following warning in kernel/irq/irqdomain.c:
kernel/irq/irqdomain.c:468:14: warning: no previous prototype for ‘irq_create_of_mapping’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/eb89aebea7ff1a46122918ac389ebecf8248be9a.1393493276.git.rashika.kheria@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We hit one rare case below:
T1 calling disable_irq(), but hanging at synchronize_irq()
always;
The corresponding irq thread is in sleeping state;
And all CPUs are in idle state;
After analysis, we found there is one possible scenerio which
causes T1 is waiting there forever:
CPU0 CPU1
synchronize_irq()
wait_event()
spin_lock()
atomic_dec_and_test(&threads_active)
insert the __wait into queue
spin_unlock()
if(waitqueue_active)
atomic_read(&threads_active)
wake_up()
Here after inserted the __wait into queue on CPU0, and before
test if queue is empty on CPU1, there is no barrier, it maybe
cause it is not visible for CPU1 immediately, although CPU0 has
updated the queue list.
It is similar for CPU0 atomic_read() threads_active also.
So we'd need one smp_mb() before waitqueue_active.that, but removing
the waitqueue_active() check solves it as wel l and it makes
things simple and clear.
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Xiaoming Wang <xiaoming.wang@intel.com>
Link: http://lkml.kernel.org/r/1393212590-32543-1-git-send-email-chuansheng.liu@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In course of the sdhci/sdio discussion with Russell about killing the
sdio kthread hackery we discovered the need to be able to wake an
interrupt thread from software.
The rationale for this is, that sdio hardware can lack proper
interrupt support for certain features. So the driver needs to poll
the status registers, but at the same time it needs to be woken up by
an hardware interrupt.
To be able to get rid of the home brewn kthread construct of sdio we
need a way to wake an irq thread independent of an actual hardware
interrupt.
Provide an irq_wake_thread() function which wakes up the thread which
is associated to a given dev_id. This allows sdio to invoke the irq
thread from the hardware irq handler via the IRQ_WAKE_THREAD return
value and provides a possibility to wake it via a timer for the
polling scenarios. That allows to simplify the sdio logic
significantly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Chris Ball <chris@printf.net>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140215003823.772565780@linutronix.de
synchronize_irq() waits for hard irq and threaded handlers to complete
before returning. For some special cases we only need to make sure
that the hard interrupt part of the irq line is not in progress when
we disabled the - possibly shared - interrupt at the device level.
A proper use case for this was provided by Russell. The sdhci driver
requires some irq triggered functions to be run in thread context. The
current implementation of the thread context is a sdio private kthread
construct, which has quite some shortcomings. These can be avoided
when the thread is directly associated to the device interrupt via the
generic threaded irq infrastructure.
Though there is a corner case related to run time power management
where one side disables the device interrupts at the device level and
needs to make sure, that an already running hard interrupt handler has
completed before proceeding further. Though that hard interrupt
handler might wake the associated thread, which in turn can request
the runtime PM to reenable the device. Using synchronize_irq() leads
to an immediate deadlock of the irq thread waiting for the PM lock and
the synchronize_irq() waiting for the irq thread to complete.
Due to the fact that it is sufficient for this case to ensure that no
hard irq handler is executing a new function which avoids the check
for the thread is required.
Add a function, which just monitors the hard irq parts and ignores the
threaded handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <linux@arm.linux.org.uk>
Cc: Chris Ball <chris@printf.net>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140215003823.653236081@linutronix.de
Pull irq update from Thomas Gleixner:
"Fix from the urgent branch: a trivial oneliner adding the missing
Kconfig dependency curing build failures which have been discovered by
several build robots.
The update in the irq-core branch provides a new function in the
irq/devres code, which is a prerequisite for driver developers to get
rid of boilerplate code all over the place.
Not a bugfix, but it has zero impact on the current kernel due to the
lack of users. It's simpler to provide the infrastructure to
interested parties via your tree than fulfilling the wishlist of
driver maintainers on which particular commit or tag this should be
based on"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add missing irq_to_desc export for CONFIG_SPARSE_IRQ=n
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add devm_request_any_context_irq()
In allmodconfig builds for sparc and any other arch which does
not set CONFIG_SPARSE_IRQ, the following will be seen at modpost:
CC [M] lib/cpu-notifier-error-inject.o
CC [M] lib/pm-notifier-error-inject.o
ERROR: "irq_to_desc" [drivers/gpio/gpio-mcp23s08.ko] undefined!
make[2]: *** [__modpost] Error 1
This happens because commit 3911ff30f5 ("genirq: export
handle_edge_irq() and irq_to_desc()") added one export for it, but
there were actually two instances of it, in an if/else clause for
CONFIG_SPARSE_IRQ. Add the second one.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org # 3.4+
Link: http://lkml.kernel.org/r/1392057610-11514-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The generic_chip.c uses interfaces from irq_domain.c which is
controlled by the IRQ_DOMAIN config option, but there is no Kconfig
dependency so the build can fail:
linux/kernel/irq/generic-chip.c:400:11: error:
'irq_domain_xlate_onetwocell' undeclared here (not in a function)
Select IRQ_DOMAIN when GENERIC_IRQ_CHIP is selected.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Link: http://lkml.kernel.org/r/1391129410-54548-2-git-send-email-nitin.a.kamble@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # 3.11+
Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
When the system enters suspend, it disables all interrupts in
suspend_device_irqs(), including the interrupts marked EARLY_RESUME.
On the resume side things are different. The EARLY_RESUME interrupts
are reenabled in sys_core_ops->resume and the non EARLY_RESUME
interrupts are reenabled in the normal system resume path.
When suspend_noirq() failed or suspend is aborted for any other
reason, we might omit the resume side call to sys_core_ops->resume()
and therefor the interrupts marked EARLY_RESUME are not reenabled and
stay disabled forever.
To solve this, enable all irqs unconditionally in irq_resume()
regardless whether interrupts marked EARLY_RESUMEhave been already
enabled or not.
This might try to reenable already enabled interrupts in the non
failure case, but the only affected platform is XEN and it has been
confirmed that it does not cause any side effects.
[ tglx: Massaged changelog. ]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Cc: <ian.campbell@citrix.com>
Cc: <rjw@rjwysocki.net>
Cc: <len.brown@intel.com>
Cc: <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1385388587-16442-1-git-send-email-ldewangan@nvidia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull irq cleanups from Ingo Molnar:
"This is a multi-arch cleanup series from Thomas Gleixner, which we
kept to near the end of the merge window, to not interfere with
architecture updates.
This series (motivated by the -rt kernel) unifies more aspects of IRQ
handling and generalizes PREEMPT_ACTIVE"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
preempt: Make PREEMPT_ACTIVE generic
sparc: Use preempt_schedule_irq
ia64: Use preempt_schedule_irq
m32r: Use preempt_schedule_irq
hardirq: Make hardirq bits generic
m68k: Simplify low level interrupt handling code
genirq: Prevent spurious detection for unconditionally polled interrupts
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
On a 68k platform a couple of interrupts are demultiplexed and
"polled" from a top level interrupt. Unfortunately there is no way to
determine which of the sub interrupts raised the top level interrupt,
so all of the demultiplexed interrupt handlers need to be
invoked. Given a high enough frequency this can trigger the spurious
interrupt detection mechanism, if one of the demultiplex interrupts
returns IRQ_NONE continuously. But this is a false positive as the
polling causes this behaviour and not buggy hardware/software.
Introduce IRQ_POLLED which can be set at interrupt chip setup time via
irq_set_status_flags(). The flag excludes the interrupt from the
spurious detector and from all core polling activities.
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1311061149250.23353@ionos.tec.linutronix.de
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
In commit ee23871389 ("genirq: Set irq thread to RT priority on
creation") we moved the assigment of the thread's priority from the
thread's function into __setup_irq(). That function may run in user
context for instance if the user opens an UART node and then driver
calls requests in the ->open() callback. That user may not have
CAP_SYS_NICE and so the irq thread won't run with the SCHED_OTHER
policy.
This patch uses sched_setscheduler_nocheck() so we omit the CAP_SYS_NICE
check which is otherwise required for the SCHED_OTHER policy.
[bigeasy: Rewrite the changelog]
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Cc: Ivo Sieben <meltedpianoman@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1381489240-29626-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All the callers of irq_create_of_mapping() pass the contents of a struct
of_phandle_args structure to the function. Since all the callers already
have an of_phandle_args pointer, why not pass it directly to
irq_create_of_mapping()?
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull irq updates from Thomas Gleixner:
- core fix for missing round up in the generic irq chip implementation
- new irq chip for MOXA SoCs
- a few fixes and cleanups in the irqchip drivers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for MOXA ART SoCs
genirq: generic chip: Use DIV_ROUND_UP to calculate numchips
irqchip: nvic: Fix wrong num_ct argument for irq_alloc_domain_generic_chips()
irqchip: sun4i: Staticize sun4i_irq_ack()
irqchip: vt8500: Staticize local symbols
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
This is the long awaited simplification of irqdomain. It gets rid of the
different types of irq domains and instead both linear and tree mappings
can be supported in a single domain. Doing this removes a lot of special
case code and makes irq domains simpler to understand overall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yJRw
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux
Pull irqdomain refactoring from Grant Likely:
"This is the long awaited simplification of irqdomain. It gets rid of
the different types of irq domains and instead both linear and tree
mappings can be supported in a single domain. Doing this removes a
lot of special case code and makes irq domains simpler to understand
overall"
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
irq: fix checkpatch error
irqdomain: Include hwirq number in /proc/interrupts
irqdomain: make irq_linear_revmap() a fast path again
irqdomain: remove irq_domain_generate_simple()
irqdomain: Refactor irq_domain_associate_many()
irqdomain: Beef up debugfs output
irqdomain: Clean up aftermath of irq_domain refactoring
irqdomain: Eliminate revmap type
irqdomain: merge linear and tree reverse mappings.
irqdomain: Add a name field
irqdomain: Replace LEGACY mapping with LINEAR
irqdomain: Relax failure path on setting up mappings
The number of interrupts in a domain may be not divisible by the
number of interrupts each chip handles. Integer division may truncate
the result, thus use DIV_ROUND_UP to count numchips.
Seems all users of irq_alloc_domain_generic_chips() in current code do
not have this issue. I just found the issue while reading the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1373015592.18252.2.camel@phoenix
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Pull core irq changes from Ingo Molnar:
"The main changes:
- generic-irqchip driver additions, cleanups and fixes
- 3 new irqchip drivers: ARMv7-M NVIC, TB10x and Marvell Orion SoCs
- irq_get_trigger_type() simplification and cross-arch cleanup
- various cleanups, simplifications
- documentation updates"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
softirq: Use _RET_IP_
genirq: Add the generic chip to the genirq docbook
genirq: generic-chip: Export some irq_gc_ functions
genirq: Fix can_request_irq() for IRQs without an action
irqchip: exynos-combiner: Staticize combiner_init
irqchip: Add support for ARMv7-M NVIC
irqchip: Add TB10x interrupt controller driver
irqdomain: Use irq_get_trigger_type() to get IRQ flags
MIPS: octeon: Use irq_get_trigger_type() to get IRQ flags
arm: orion: Use irq_get_trigger_type() to get IRQ flags
mfd: stmpe: use irq_get_trigger_type() to get IRQ flags
mfd: twl4030-irq: Use irq_get_trigger_type() to get IRQ flags
gpio: mvebu: Use irq_get_trigger_type() to get IRQ flags
genirq: Add irq_get_trigger_type() to get IRQ flags
genirq: Irqchip: document gcflags arg of irq_alloc_domain_generic_chips
genirq: Set irq thread to RT priority on creation
irqchip: Add support for Marvell Orion SoCs
genirq: Add kerneldoc for irq_disable.
genirq: irqchip: Add mask to block out invalid irqs
genirq: Generic chip: Add linear irq domain support
...
When building imx_v6_v7_defconfig with imx-drm drivers selected as
modules, we get the following build errors:
ERROR: "irq_gc_mask_clr_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_mask_set_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_ack_set_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
Export the required functions to avoid this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: shawn.guo@linaro.org
Cc: kernel@pengutronix.de
Link: http://lkml.kernel.org/r/1372389789-7048-1-git-send-email-festevam@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 02725e7471 ('genirq: Use irq_get/put functions'),
inadvertently changed can_request_irq() to return 0 for IRQs that have
no action. This causes pcibios_lookup_irq() to select only IRQs that
already have an action with IRQF_SHARED set, or to fail if there are
none. Change can_request_irq() to return 1 for IRQs that have no
action (if the first two conditions are met).
Reported-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Tested-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is> (against 3.2)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: 709647@bugs.debian.org
Cc: stable@vger.kernel.org # 2.6.39+
Link: http://bugs.debian.org/709647
Link: http://lkml.kernel.org/r/1372383630.23847.40.camel@deadeye.wl.decadent.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use irq_get_trigger_type() to get the IRQ trigger type flags
instead calling irqd_get_trigger_type(irq_desc_get_irq_data(virq))
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1371228049-27080-8-git-send-email-javier.martinez@collabora.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 088f40b7b0 ("genirq: Generic chip:
Add linear irq domain support") missed kerneldoc for the gcflags
argument of irq_alloc_domain_generic_chips(). Add it now.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Link: http://lkml.kernel.org/r/1371564513-4327-1-git-send-email-james.hogan@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ERROR: space required before the open parenthesis '('
WARNING: Prefer pr_warn(... to pr_warning(...
Just fix above 2 issue.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Add the hardware interrupt number to the output of /proc/interrupts.
It is often important to have access to the hardware interrupt number because
it identifies exactly how an interrupt signal is wired up to the interrupt
controller. This is especially important when using irq_domains since irq
numbers get dynamically allocated in that case, and have no relation to the
actual hardware number.
Note: This output is currently conditional on whether or not the irq_domain
pointer is set; however hwirq could still be used without irq_domain. It
may be worthwhile to always output the hwirq number regardless of the
domain pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Over the years, irq_linear_revmap() gained tests and checks to make sure
callers were using it safely, which while important, also make it less
of a fast path. After the irqdomain refactoring done recently, it is now
possible to make irq_linear_revmap() a fast path again. This patch moves
irq_linear_revmap() to the header file and makes it a static inline so
that interrupt controller drivers using a linear mapping can decode the
virq from a hwirq in just a couple of instructions.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Originally, irq_domain_associate_many() was designed to unwind the
mapped irqs on a failure of any individual association. However, that
proved to be a problem with certain IRQ controllers. Some of them only
support a subset of irqs, and will fail when attempting to map a
reserved IRQ. In those cases we want to map as many IRQs as possible, so
instead it is better for irq_domain_associate_many() to make a
best-effort attempt to map irqs, but not fail if any or all of them
don't succeed. If a caller really cares about how many irqs got
associated, then it should instead go back and check that all of the
irqs is cares about were mapped.
The original design open-coded the individual association code into the
body of irq_domain_associate_many(), but with no longer needing to
unwind associations, the code becomes simpler to split out
irq_domain_associate() to contain the bulk of the logic, and
irq_domain_associate_many() to be a simple loop wrapper.
This patch also adds a new error check to the associate path to make
sure it isn't called for an irq larger than the controller can handle,
and adds locking so that the irq_domain_mutex is held while setting up a
new association.
v3: Fixup missing change to irq_domain_add_tree()
v2: Fixup x86 warning. irq_domain_associate_many() no longer returns an
error code, but reports errors to the printk log directly. In the
majority of cases we don't actually want to fail if there is a
problem, but rather log it and still try to boot the system.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
irqdomain: Fix flubbed irq_domain_associate_many refactoring
commit d39046ec72, "irqdomain: Refactor irq_domain_associate_many()" was
missing the following hunk which causes a boot failure on anything using
irq_domain_add_tree() to allocate an irq domain.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>,
Cc: Thomas Gleixner <tglx@linutronix.de>,
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
When a threaded irq handler is installed the irq thread is initially
created on normal scheduling priority. Only after the irq thread is
woken up it sets its priority to RT_FIFO MAX_USER_RT_PRIO/2 itself.
This means that interrupts that occur directly after the irq handler
is installed will be handled on a normal scheduling priority instead
of the realtime priority that one would expect.
Fix this by setting the RT priority on creation of the irq_thread.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1370254322-17240-1-git-send-email-meltedpianoman@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch increases the amount of output produced by the
irq_domain_mapping debugfs file by first listing all of the registered
irq domains at the beginning of the output, and then by including all
mapped IRQs in the output, not just the active ones. It is very useful
when debugging irqdomain issues to be able to see the entire list of
mapped irqs, not just the ones that happen to be connected to devices.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
After refactoring the irqdomain code, there are a number of API
functions that are merely empty wrappers around core code. Drop those
wrappers out of the C file and replace them with static inlines in the
header.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The NOMAP irq_domain type is only used by a handful of interrupt
controllers and it unnecessarily complicates the code by adding special
cases on how to look up mappings and different revmap functions are used
for each type which need to validate the correct type is passed to it
before performing the reverse map. Eliminating the revmap_type and
making a single reverse mapping function simplifies the code. It also
shouldn't be any slower than having separate revmap functions because
the type of the revmap needed to be checked anyway.
The linear and tree revmap types were already merged in a previous
patch. This patch rolls the NOMAP or direct mapping behaviour into the
same domain code making is possible for an irq domain to do any mapping
type; linear, tree or direct; and that the mapping will be transparent
to the interrupt controller driver.
With this change, direct mappings will get stored in the linear or tree
mapping for consistency. Reverse mapping from the hwirq to virq will go
through the normal lookup process. However, any controller using a
direct mapping can take advantage of knowing that hwirq==virq for any
mapped interrupts skip doing a revmap lookup when handling IRQs.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Keeping them separate makes irq_domain more complex and adds a lot of
code (as proven by the diffstat). Merging them simplifies the whole
scheme. This change makes it so both the tree and linear methods can be
used by the same irq_domain instance. If the hwirq is less than the
->linear_size, then the linear map is used to reverse map the hwirq.
Otherwise the radix tree is used. The test for which map to use is no
more expensive that the existing code, so the performance of fast path
is preserved.
It also means that complex interrupt controllers can use both the
linear map and a tree in the same domain. This may be useful for an
interrupt controller with a base set of core irqs and a large number
of GPIOs which might be used as irqs. The linear map could cover the
core irqs, and the tree used for thas irqs. The linear map could
cover the core irqs, and the tree used for the gpios.
v2: Drop reorganization of revmap data
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
This patch adds a name field to the irq_domain structure to help mere
mortals understand the mappings between irq domains and virqs. It also
converts a number of places that have open-coded some kind of fudging
an irqdomain name to use the new field. This means a more consistent
display of names in irq domain log messages and debugfs output.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The LEGACY mapping unnecessarily complicates the irqdomain code and
can easily be implemented with a linear mapping. By ripping it out
and replacing it with the LINEAR mapping the object size of
irqdomain.c shrinks by about 330 bytes (ARMv7) which offsets the
additional allocation required by the linear map. It also makes it
possible for current LEGACY map users to pre-allocate irq_descs for a
subset of the hwirqs and dynamically allocate the rest as needed.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Commit 98aa468e, "irqdomain: Support for static IRQ mapping and
association" introduced an API for directly associating blocks of hwirqs
to linux irqs. However, if any irq in that block failed to map (say if
the mapping functions returns an error because the irq is already
mapped) then the whole thing will fail and roll back. This is probably
too aggressive since there are valid reasons why a mapping may fail.
ie. Firmware may have a particular IRQ marked as unusable.
This patch drops the error path out of irq_domain_associate(). If a
mapping fails, then it is simply skipped. There is no reason to fail the
entire allocation.
v2: Still output an information message on failed mappings and make sure
attempted mapping gets cleared out of the irq_data structure.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Some controllers have irqs that aren't wired up and must never be used.
For the generic chip attached to an irq_domain this provides a mask that
can be used to block out particular irqs so that they never get mapped.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1369793454-19197-2-git-send-email-grant.likely@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide infrastructure for irq chip implementations which work on
linear irq domains.
- Interface to allocate multiple generic chips which are associated to
the irq domain.
- Interface to get the generic chip pointer for a particular hardware
interrupt in the domain.
- irq domain mapping function to install the chip for a particular
interrupt.
Note: This lacks a removal function for now.
[ Sebastian Hesselbarth: Mask cache and pointer math fixups ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.450634298@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Preparatory patch for linear interrupt domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.377017672@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some chips have weird bit mask access patterns instead of the linear
you expect. Allow them to calculate the cached mask themself.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.302898834@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cache the per irq bit mask instead of recalculating it over and over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.227119865@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are cases where all irq_chip_type instances have separate mask
registers, making a shared mask register cache unsuitable for the
purpose.
Introduce a new flag IRQ_GC_MASK_CACHE_PER_TYPE. If set, point the per
chip mask pointer to the per chip private mask cache instead.
[ tglx: Simplified code, renamed flag and massaged changelog ]
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Joey Oravec <joravec@drewtech.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.152569748@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Today the same interrupt mask cache (stored within struct irq_chip_generic)
is shared between all the irq_chip_type instances. As there are instances
where each irq_chip_type uses a distinct mask register (as it is the case
for Orion SoCs), sharing a single mask cache may be incorrect.
So add a distinct pointer for each irq_chip_type, which for now
points to the original mask register within irq_chip_generic.
So no functional changes here.
[ tglx: Minor cosmetic tweaks ]
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.082226607@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since we already have an irq_data_get_chip_type() function which returns
a pointer to irq_chip_type, use that instead of cur_regs().
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Joey Oravec <joravec@drewtech.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.010164766@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some interrupt controllers refuse to map interrupts marked as
"protected" by firwmare. Since we try to map everyting in the
device-tree on some platforms, we end up with a lot of nasty
WARN's in the boot log for what is a normal situation on those
machines.
This defines a specific return code (-EPERM) from the host map()
callback which cause irqdomain to fail silently.
MPIC is updated to return this when hitting a protected source
printing only a single line message for diagnostic purposes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
Move rt scheduler definitions out of include/linux/sched.h into
new file include/linux/sched/rt.h
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The MSI specification has several constraints in comparison with
MSI-X, most notable of them is the inability to configure MSIs
independently. As a result, it is impossible to dispatch
interrupts from different queues to different CPUs. This is
largely devalues the support of multiple MSIs in SMP systems.
Also, a necessity to allocate a contiguous block of vector
numbers for devices capable of multiple MSIs might cause a
considerable pressure on x86 interrupt vector allocator and
could lead to fragmentation of the interrupt vectors space.
This patch overcomes both drawbacks in presense of IRQ remapping
and lets devices take advantage of multiple queues and per-IRQ
affinity assignments.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/c8bd86ff56b5fc118257436768aaa04489ac0a4c.1353324359.git.agordeev@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ+MDOAAoJEHm+PkMAQRiGFL8H/39bXl3xs/ZkBct3ciICtaAt
UeRcdjvBdUrObQmmw8FEFJA62Az74g1UYyNyc0yVJoB6DwL2oawXhGXQXqDXMBMs
xJa/dpx41gmcrvsLOJ1v2Tmokk32hgdpLNWwzcn36xZMsrhYUxjxPhVNK4aDbwrW
3uzBj83dK1rvi2PEz3hgHizRhmdD1cNgLXKrczNbT6y6rLp6Jkng2q5UhNfaZUvE
A7Ub5/nW+X6gb1PctAjulz2CoySq0FbH4viUc+zLj3NN0L9ImeJvpREauE2QPVgJ
a8Sg3E6/cL4wIXBEV1E1KapVTd1XIEGa8yB5X6q8HWNKI8nf7Kwuj65VgvwJIMc=
=+VR8
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc4' into irq/core
Merge Linux 3.8-rc4 before pulling in new commits - we were on an old v3.7 base.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The array check is useless so remove it.
[akpm@linux-foundation.org: remove comment, per David]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull irq fixes from Ingo Molnar:
"Affinity fixes and a nested threaded IRQ handling fix."
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Always force thread affinity
irq: Set CPU affinity right on thread creation
genirq: Provide means to retrigger parent
commit 52553ddf(genirq: fix regression in irqfixup, irqpoll)
introduced a potential deadlock by calling the action handler with the
irq descriptor lock held.
Remove the call and let the handling code run even for an interrupt
where only a single action is registered. That matches the goal of
the above commit and avoids the deadlock.
Document the confusing action = desc->action reload in the handling
loop while at it.
Reported-and-tested-by: "Wang, Warner" <warner.wang@hp.com>
Tested-by: Edward Donovan <edward.donovan@numble.net>
Cc: "Wang, Song-Bo (Stoney)" <song-bo.wang@hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the simple irqdomain: don't shout warnings to the user,
there is no point. An informational print is sufficient.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sankara reported that the genirq core code fails to adjust the
affinity of an interrupt thread in several cases:
1) On request/setup_irq() the call to setup_affinity() happens before
the new action is registered, so the new thread is not notified.
2) For secondary shared interrupts nothing notifies the new thread to
change its affinity.
3) Interrupts which have the IRQ_NO_BALANCE flag set are not moving
the thread either.
Fix this by setting the thread affinity flag right on thread creation
time. This ensures that under all circumstances the thread moves to
the right place. Requires a check in irq_thread_check_affinity for an
existing affinity mask (CONFIG_CPU_MASK_OFFSTACK=y)
Reported-and-tested-by: Sankara Muthukrishnan <sankara.m@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1209041738200.2754@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As irq_thread_check_affinity is called ONLY inside the while loop in
the irq thread, the core affinity is set only when an interrupt
occurs. This patch sets the core affinity right after the irq thread
is created and before it waits for interrupts. In real-tiime targets
that do not typically change the core affinity of irqs during
run-time, this patch will save additional latency of an irq thread in
setting the core affinity during the first interrupt occurrence for
that irq.
Signed-off-by: Sankara S Muthukrishnan <sankara.m@ni.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/CAFQPvXeVZ858WFYimEU5uvLNxLDd6bJMmqWihFmbCf3ntokz0A@mail.gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Attempts to retrigger nested threaded IRQs currently fail because they
have no primary handler. In order to support retrigger of nested
IRQs, the parent IRQ needs to be retriggered.
To fix, when an IRQ needs to be resent, if the interrupt has a parent
IRQ and runs in the context of the parent IRQ, then resend the parent.
Also, handle_nested_irq() needs to clear the replay flag like the
other handlers, otherwise check_irq_resend() will set it and it will
never be cleared. Without clearing, it results in the first resend
working fine, but check_irq_resend() returning early on subsequent
resends because the replay flag is still set.
Problem discovered on ARM/OMAP platforms where a nested IRQ that's
also a wakeup IRQ happens late in suspend and needed to be retriggered
during the resume process.
[khilman@ti.com: changelog edits, clear IRQS_REPLAY in handle_nested_irq()]
Reported-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1350425269-11489-1-git-send-email-khilman@deeprootsystems.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently we rely on all IRQ chip instances to dynamically
allocate their IRQ descriptors unless they use the linear
IRQ domain. So for irqdomain_add_legacy() and
irqdomain_add_simple() the caller need to make sure that
descriptors are allocated.
Let's slightly augment the yet unused irqdomain_add_simple()
to also allocate descriptors as a means to simplify usage
and avoid code duplication throughout the kernel.
We warn if descriptors cannot be allocated, e.g. if a
platform has the bad habit of hogging descriptors at boot
time.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Export dummy_irq_chip to modules to allow them to do things such as
irq_set_chip_and_handler(virq,
&dummy_irq_chip,
handle_level_irq);
This fixes
ERROR: "dummy_irq_chip" [drivers/gpio/gpio-pcf857x.ko] undefined!
when gpio-pcf857x.c is being built as a module.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Greg KH <gregkh@linuxfoundation.org>
Link: http://lkml.kernel.org/r/871ujstrp6.wl%25kuninori.morimoto.gx@renesas.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export irq_set_chip_and_handler_name() to modules to allow them to
do things such as
irq_set_chip_and_handler(....);
This fixes
ERROR: "irq_set_chip_and_handler_name" \
[drivers/gpio/gpio-pcf857x.ko] undefined!
when gpio-pcf857x.c is being built as a module.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Greg KH <gregkh@linuxfoundation.org>
Link: http://lkml.kernel.org/r/873948trpk.wl%25kuninori.morimoto.gx@renesas.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull irq fix from Ingo Molnar.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Allow irq chips to mark themself oneshot safe
Round of refactoring and enhancements to irq_domain infrastructure. This
series starts the process of simplifying irqdomain. The ultimate goal is
to merge LEGACY, LINEAR and TREE mappings into a single system, but had
to back off from that after some last minute bugs. Instead it mainly
reorganizes the code and ensures that the reverse map gets populated
when the irq is mapped instead of the first time it is looked up.
Merging of the irq_domain types is deferred to v3.7
In other news, this series adds helpers for creating static mappings on
a linear or tree mapping.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZUF/
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irqdomain changes from Grant Likely:
"Round of refactoring and enhancements to irq_domain infrastructure.
This series starts the process of simplifying irqdomain. The ultimate
goal is to merge LEGACY, LINEAR and TREE mappings into a single
system, but had to back off from that after some last minute bugs.
Instead it mainly reorganizes the code and ensures that the reverse
map gets populated when the irq is mapped instead of the first time it
is looked up.
Merging of the irq_domain types is deferred to v3.7
In other news, this series adds helpers for creating static mappings
on a linear or tree mapping."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irqdomain: Improve diagnostics when a domain mapping fails
irqdomain: eliminate slow-path revmap lookups
irqdomain: Fix irq_create_direct_mapping() to test irq_domain type.
irqdomain: Eliminate dedicated radix lookup functions
irqdomain: Support for static IRQ mapping and association.
irqdomain: Always update revmap when setting up a virq
irqdomain: Split disassociating code into separate function
irq_domain: correct a minor wrong comment for linear revmap
irq_domain: Standardise legacy/linear domain selection
irqdomain: Make ops->map hook optional
irqdomain: Remove unnecessary test for IRQ_DOMAIN_MAP_LEGACY
irqdomain: Simple NUMA awareness.
devicetree: add helper inline for retrieving a node's full name
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
Some interrupt chips like MSI are oneshot safe by implementation. For
those interrupts we can avoid the mask/unmask sequence for threaded
interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1207132056540.32033@ionos
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Jan Kiszka <jan.kiszka@web.de>
When the map operation fails log the error code we get and add a WARN_ON()
so we get a backtrace (which should help work out which interrupt is the
source of the issue).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With the current state of irq_domain, the reverse map is always updated
when new IRQs get mapped. This means that the irq_find_mapping() function
can be simplified to execute the revmap lookup functions unconditionally
This patch adds lookup functions for the revmaps that don't yet have one
and removes the slow path lookup code path.
v8: Broke out unrelated changes into separate patches. Rebased on Paul's irq
association patches.
v7: Rebased to irqdomain/next for v3.4 and applied before the removal of 'hint'
v6: Remove the slow path entirely. The only place where the slow path
could get called is for a linear mapping if the hwirq number is larger
than the linear revmap size. There shouldn't be any interrupt
controllers that do that.
v5: rewrite to not use a ->revmap() callback. It is simpler, smaller,
safer and faster to open code each of the revmap lookups directly into
irq_find_mapping() via a switch statement.
v4: Fix build failure on incorrect variable reference.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Rob Herring <rob.herring@calxeda.com>
A small set of changes for devicetree:
- Couple of Documentation fixes
- Addition of new helper function of_node_full_name
- Improve of_parse_phandle_with_args return values
- Some NULL related sparse fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQDwsgAAoJEMhvYp4jgsXiuwUH/Ri6ZSnqHcz4Wa/X4FxvNc3I
3Xelo/Vt3WLYue3s/+OYiM5FK9+KH8T6x+U79Q4p7vePcfUh6GJII0AUbMeRghkS
m3FjNd5syzYNJlnDnqdngQYRDpaz8U/SyftjXyMPjJ1VWiyLx/EJQUkj1EEwDLe/
ZVabppnco3Y6OJpFuETONNvXx5mE7xq86isW5+aYmviMkWSMMwJPf8qofLJ78Dh5
OAhWuCPRDooz548+Wkabt90qHjF6FU43w5fU7zZW26NT39ptppcbZ2bAXcTYqIIq
sATp5YSitvwFqO2c1mA/drZ9nrgxDPCaw3qCDyiMdcbWgXqDirz2x7q1iauVHF4=
=5TZ/
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.6' of git://sources.calxeda.com/kernel/linux
Pull devicetree updates from Rob Herring:
"A small set of changes for devicetree:
- Couple of Documentation fixes
- Addition of new helper function of_node_full_name
- Improve of_parse_phandle_with_args return values
- Some NULL related sparse fixes"
Grant's busy packing.
* tag 'dt-for-3.6' of git://sources.calxeda.com/kernel/linux:
of: mtd: nuke useless const qualifier
devicetree: add helper inline for retrieving a node's full name
of: return -ENOENT when no property
usage-model.txt: fix typo machine_init->init_machine
of: Fix null pointer related warnings in base.c file
LED: Fix missing semicolon in OF documentation
of: fix a few typos in the binding documentation
task_work and rcu_head are identical now; merge them (calling the result
struct callback_head, rcu_head #define'd to it), kill separate allocation
in security/keys since we can just use cred->rcu now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
get rid of the only user of ->data; this is _not_ the final variant - in the
end we'll have task_work and rcu_head identical and just use cred->rcu,
at which point the separate allocation will be gone completely.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With the new interrupt sampling system, we are no longer using the
timer_rand_state structure in the irq descriptor, so we can stop
initializing it now.
[ Merged in fixes from Sedat to find some last missing references to
rand_initialize_irq() ]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
We've been moving away from add_interrupt_randomness() for various
reasons: it's too expensive to do on every interrupt, and flooding the
CPU with interrupts could theoretically cause bogus floods of entropy
from a somewhat externally controllable source.
This solves both problems by limiting the actual randomness addition
to just once a second or after 64 interrupts, whicever comes first.
During that time, the interrupt cycle data is buffered up in a per-cpu
pool. Also, we make sure the the nonblocking pool used by urandom is
initialized before we start feeding the normal input pool. This
assures that /dev/urandom is returning unpredictable data as soon as
possible.
(Based on an original patch by Linus, but significantly modified by
tytso.)
Tested-by: Eric Wustrow <ewust@umich.edu>
Reported-by: Eric Wustrow <ewust@umich.edu>
Reported-by: Nadia Heninger <nadiah@cs.ucsd.edu>
Reported-by: Zakir Durumeric <zakir@umich.edu>
Reported-by: J. Alex Halderman <jhalderm@umich.edu>.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
irq_create_direct_mapping can only be used with the NOMAP type. Make
the function test to ensure it is passed the correct type of
irq_domain.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
In preparation to remove the slow revmap path, eliminate the public
radix revmap lookup functions. This simplifies the code and makes the
slowpath removal patch a lot simpler.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
This adds a new strict mapping API for supporting creation of linux IRQs
at existing positions within the domain. The new routines are as follows:
For dynamic allocation and insertion to specified ranges:
- irq_create_identity_mapping()
- irq_create_strict_mappings()
These will allocate and associate a range of linux IRQs at the specified
location. This can be used by controllers that have their own static linux IRQ
definitions to map a hwirq range to, as well as for platforms that wish to
establish 1:1 identity mapping between linux and hwirq space.
For insertion to specified ranges by platforms that do their own irq_desc
management:
- irq_domain_associate()
- irq_domain_associate_many()
These in turn call back in to the domain's ->map() routine, for further
processing by the platform. Disassociation of IRQs get handled through
irq_dispose_mapping() as normal.
With these in place it should be possible to begin migration of legacy IRQ
domains to linear ones, without requiring special handling for static vs
dynamic IRQ definitions in DT vs non-DT paths. This also makes it possible
for domains with static mappings to adopt whichever tree model best fits
their needs, rather than simply restricting them to linear revmaps.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
[grant.likely: Reorganized irq_domain_associate{,_many} to have all logic in one place]
[grant.likely: Add error checking for unallocated irq_descs at associate time]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
At irq_setup_virq() time all of the data needed to update the reverse
map is available, but the current code ignores it and relies upon the
slow path to insert revmap records. This patch adds revmap updating
to the setup path so the slow path will no longer be necessary.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
This patch moves the irq disassociation code out into a separate
function in preparation to extend irq_setup_virq to handle multiple
irqs and rename it for use by interrupt controller drivers. The new
function will be used by irq_setup_virq() in its error path.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
The revmap type should be linear for irq_domain_add_linear function.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A large proportion of interrupt controllers that support legacy mappings
do so because non-DT systems need to use fixed IRQ numbers when registering
devices via buses but can otherwise use a linear mapping. The interrupt
controller itself typically is not affected by the mapping used and best
practice is to use a linear mapping where possible so drivers frequently
select at runtime depending on if a legacy range has been allocated to
them.
Standardise this behaviour by providing irq_domain_register_simple() which
will allocate a linear mapping unless a positive first_irq is provided in
which case it will fall back to a legacy mapping. This helps make best
practice for irq_domain adoption clearer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The pattern (np ? np->full_name : "<none>") is rather common in the
kernel, but can also make for quite long lines. This patch adds a new
inline function, of_node_full_name() so that the test for a valid node
pointer doesn't need to be open coded at all call sites.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
There isn't a really compelling reason to force ->map to be populated,
so allow it to be left unset.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Where irq_domain_associate() is called in irq_create_mapping, there is
no need to test for IRQ_DOMAIN_MAP_LEGACY because it is already tested
for earlier in the routine.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
While common irqdesc allocation is node aware, the irqdomain code is not.
Presently we observe a number of regressions/inconsistencies on
NUMA-capable platforms:
- Platforms using irqdomains with legacy mappings, where the
irq_descs are allocated node-local and the irqdomain data
structure is not.
- Drivers implementing irqdomains will lose node locality
regardless of the underlying struct device's node id.
This plugs in NUMA node id proliferation across the various allocation
callsites by way of_node_to_nid() node lookup. While of_node_to_nid()
does the right thing for OF-capable platforms it doesn't presently handle
the non-DT case. This is trivially dealt with by simply wraping in to
numa_node_id() unconditionally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The pattern (np ? np->full_name : "<none>") is rather common in the
kernel, but can also make for quite long lines. This patch adds a new
inline function, of_node_full_name() so that the test for a valid node
pointer doesn't need to be open coded at all call sites.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Pull irq and smpboot updates from Thomas Gleixner:
"Just cleanup patches with no functional change and a fix for suspend
issues."
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Introduce irq_do_set_affinity() to reduce duplicated code
genirq: Add IRQS_PENDING for nested and simple irq
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smpboot, idle: Fix comment mismatch over idle_threads_init()
smpboot, idle: Optimize calls to smp_processor_id() in idle_threads_init()
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
Use the module-wide pr_fmt() mechanism rather than open-coding "genirq: "
everywhere.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor changes and fixups for irqdomain infrastructure. Most
important change adds ability to remove registered irqdomain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K3Pg
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irqdomain changes from Grant Likely:
"Minor changes and fixups for irqdomain infrastructure. The most
important change adds the ability to remove a registered irqdomain."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irqdomain: Document size parameter of irq_domain_add_linear()
irqdomain: trivial pr_fmt conversion.
irqdomain: Kill off duplicate definitions.
irqdomain: Make irq_domain_simple_map() static.
irqdomain: Export remaining public API symbols.
irqdomain: Support removal of IRQ domains.
All invocations of chip->irq_set_affinity() are doing the same return
value checks. Let them all use a common function.
[ tglx: removed the silly likely while at it ]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Keping Chen <chenkeping@huawei.com>
Link: http://lkml.kernel.org/r/1333120296-13563-3-git-send-email-jiang.liu@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Every interrupt which is an active wakeup source needs the ability to
abort suspend if there is a pending irq. Right now only edge and level
irqs can do that.
|
+---------+
| INTC |
+---------+
| GPIO_IRQ
+------------+
| gpio-exp |
+------------+
| |
GPIO0_IRQ GPIO1_IRQ
In the above diagram, gpio expander has irq number GPIO_IRQ, it is
connected with two sub GPIO pins, GPIO0 and GPIO1.
During suspend, we set IRQF_NO_SUSPEND for GPIO_IRQ so that gpio
expander driver can handle the sub irq GPIO0_IRQ and GPIO1_IRQ, and
these two irqs themselves can further be handled by simple or nested
irq in some drivers(typically gpio and mfd driver). If they are used
as wakeup sources during suspend, we want them to be able to abort
suspend too.
Setting IRQS_PENDING flag in handle_nested_irq() and handle_simple_irq()
when the irq is disabled allows check_wakeup_irqs() to identify such
irqs as source for aborting suspend.
Signed-off-by: Ning Jiang <ning.n.jiang@gmail.com>
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/CAH3Oq6T905%2B3fkF43NAMMFvJvq7dsk_so6T2vQ8ZJrA5xiU3YA@mail.gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
exit_irq_thread() and task->irq_thread are needed to handle the unexpected
(and unlikely) exit of irq-thread.
We can use task_work instead and make this all private to
kernel/irq/manage.c, cleanup plus micro-optimization.
1. rename exit_irq_thread() to irq_thread_dtor(), make it
static, and move it up before irq_thread().
2. change irq_thread() to do task_work_add(irq_thread_dtor)
at the start and task_work_cancel() before return.
tracehook_notify_resume() can never play with kthreads,
only do_exit()->exit_task_work() can call the callback
and this is what we want.
3. remove task_struct->irq_thread and the special hook
in do_exit().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Smith <dsmith@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull UML updates from Richard Weinberger:
"Most changes are bug fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: missing checks of __put_user()/__get_user() return values
um: stub_rt_sigsuspend isn't needed these days anymore
um/x86: merge (and trim) 32- and 64-bit variants of ptrace.h
irq: Remove irq_chip->release()
um: Remove CONFIG_IRQ_RELEASE_METHOD
um: Remove usage of irq_chip->release()
um: Implement um_free_irq()
um: Fix __swp_type()
um: Implement a custom pte_same() function
um: Add BUG() to do_ops()'s error path
um: Remove unused variables
um: bury unused _TIF_RESTORE_SIGMASK
um: wrong sigmask saved in case of multiple sigframes
um: add TIF_NOTIFY_RESUME
um: ->restart_block.fn needs to be reset on sigreturn
Pull core irq changes from Ingo Molnar:
"A collection of small fixes."
By Thomas Gleixner
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hexagon: Remove select of not longer existing Kconfig switches
arm: Select core options instead of redefining them
genirq: Do not consider disabled wakeup irqs
genirq: Allow check_wakeup_irqs to notice level-triggered interrupts
genirq: Be more informative on irq type mismatch
genirq: Reject bogus threaded irq requests
genirq: Streamline irq_action
As it's only user (UML) does no longer need it we can get
rid of it.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Convert to pr_fmt before things start to get out of hand and some
janitors start getting overly excited.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Presently irq_domain_simple_map() isn't labelled as static, but there's
no definition for it in the public irqdomain header either. At present
all in-tree ->map users have meaningful work to do, and all others are
using irq_domain_simple_ops directly. Make it static for now, as it can
always be exported and added to the public API later.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
modules making use of irq domains at the very least need access to the
add/remove/lookup routines, though there's nothing preventing them from
using the remainder of the public API, either.
The current set of exports seem primarily geared at DT-enabled platforms
using DT-backed IRQ domains, where many of the API accesses are hidden
away in OF code. The non-DT cases need to do most of this on their own.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now that IRQ domains are being used by modules it's necessary to support
removing them, too. This adds a new irq_domain_remove() routine for doing
the bulk of the heavy lifting. It's left as an exercise to the caller to
ensure all mappings have been appropriatey disposed of before attempting
to remove the domain.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Export handle_edge_irq() and irq_to_desc() to modules to allow them to
do things such as
__irq_set_handler_locked(...., handle_edge_irq);
This fixes
ERROR: "handle_edge_irq" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_to_desc" [drivers/gpio/gpio-pch.ko] undefined!
when gpio-pch is being built as a module.
This was introduced by commit df9541a60a ("gpio: pch9: Use proper flow
type handlers") that added
__irq_set_handler_locked(d->irq, handle_edge_irq);
but handle_edge_irq() was not exported for modules (and inlined
__irq_set_handler_locked() requires irq_to_desc() exported as well)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an wakeup interrupt has been disabled before the suspend code
disables all interrupts then we have to ignore the pending flag.
Otherwise we would abort suspend over and over as nothing clears the
pending flag because the interrupt is disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: NeilBrown <neilb@suse.de>
Level triggered interrupts do not cause IRQS_PENDING to be set when
they fire while "disabled" as the 'pending' state is always present in
the level - they automatically refire where re-enabled.
However the IRQS_PENDING flag is also used to abort a suspend cycle -
if any 'is_wakeup_set' interrupt is PENDING, check_wakeup_irqs() will
cause suspend to abort. Without IRQS_PENDING, suspend won't abort.
Consequently, level-triggered interrupts that fire during the 'noirq'
phase of suspend do not currently abort suspend.
So set IRQS_PENDING even for level triggered interrupts, and make sure
to clear the flag in check_irq_resend.
[ Changelog by courtesy of Neil ]
Tested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The file kernel/irq/debug.h temporarily defines P, PS, PD
and then undefines them. However these names aren't really
"internal" enough, and collide with other more legit users
such as the ones in the xtensa arch, causing:
In file included from kernel/irq/internals.h:58:0,
from kernel/irq/irqdesc.c:18:
kernel/irq/debug.h:8:0: warning: "PS" redefined [enabled by default]
arch/xtensa/include/asm/regs.h:59:0: note: this is the location of the previous definition
Add a handful of underscores to do a better job of hiding these
temporary macros.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We require that shared interrupts agree on a few flag settings. Right
now we silently return with an error code without giving any hint why
we reject it.
Make the printout unconditionally and actually useful by printing the
flags of the new and the already registered action.
Convert all printks to pr_* and use a proper prefix while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Requesting a threaded interrupt without a primary handler and without
IRQF_ONESHOT set is dangerous.
The core will use the default primary handler for it, which merily
wakes the thread. For a level type interrupt this results in an
interrupt storm, because the interrupt line is reenabled after the
primary handler runs. The device has still the line asserted, which
brings us back into the primary handler.
While this works for edge type interrupts, we play it safe and reject
unconditionally because we can't say for sure which type this
interrupt really has. The type flags are unreliable as the underlying
chip implementation can override them. And we cannot assume that
developers using that interface know what they are doing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
sizeof(void*) returns an unsigned long, but it was being used as a width parameter to a "%-*s" format string which requires an int. On 64 bit platforms this causes a type mismatch:
linux/kernel/irq/irqdomain.c:575: warning: field width should have type
'int', but argument 6 has type 'long unsigned int'
This change casts the size to an int so printf gets the right data type.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
This patch replaces the old global setting of irq_virq_count that is only
used by the NOMAP mapping and instead uses a revmap_data property so that
the maximum NOMAP allocation can be set per NOMAP irq_domain.
There is exactly one user of irq_virq_count in-tree right now: PS3.
Also, irq_virq_count is only useful for the NOMAP mapping. So,
instead of having a single global irq_virq_count values, this change
drops it entirely and added a max_irq argument to irq_domain_add_nomap().
That makes it a property of an individual nomap irq domain instead of
a global system settting.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
This patch fixes the irq_domain_mapping debugfs output to pad pointer
values with leading zeros so that pointer values are displayed
correctly. Otherwise you get output similar to "0x 5e0000000000000".
Also, when the irq_domain is set to 'null'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
The actual name of the irq_domain mapping debugfs file is
"irq_domain_mapping" not "virq_mapping".
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In commit 4bbdd45a (irq_domain/powerpc: eliminate irq_map; use
irq_alloc_desc() instead) code was added that ignores error returns
from irq_alloc_desc_from() by (silently) casting the return value to
unsigned. The negitive value error return now suddenly looks like a
valid irq number.
Commits cc79ca69 (irq_domain: Move irq_domain code from powerpc to
kernel/irq) and 1bc04f2c (irq_domain: Add support for base irq and
hwirq in legacy mappings) move this code to its current location in
irqdomain.c
The result of all of this is a null pointer dereference OOPS if one of
the error cases is hit.
The fix: Don't cast away the negativeness of the return value and then
check for errors.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: dropped addition of new 'irq' variable]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull genirq updates from Thomas Gleixner.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Adjust irq thread affinity on IRQ_SET_MASK_OK_NOCOPY return value
genirq: Respect NUMA node affinity in setup_irq_irq affinity()
genirq: Get rid of unneeded force parameter in irq_finalize_oneshot()
genirq: Minor readablity improvement in irq_wake_thread()
irq_move_masked_irq() checks the return code of
chip->irq_set_affinity() only for 0, but IRQ_SET_MASK_OK_NOCOPY is
also a valid return code, which is there to avoid a redundant copy of
the cpumask. But in case of IRQ_SET_MASK_OK_NOCOPY we not only avoid
the redundant copy, we also fail to adjust the thread affinity of an
eventually threaded interrupt handler.
Handle IRQ_SET_MASK_OK (==0) and IRQ_SET_MASK_OK_NOCOPY(==1) return
values correctly by checking the valid return values seperately.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Keping Chen <chenkeping@huawei.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1333120296-13563-2-git-send-email-jiang.liu@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
The debugfs code is really generic for all platforms. This patch removes the
powerpc-specific directory reference and makes it available to all
architectures.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We respect node affinity of devices already in the irq descriptor
allocation, but we ignore it for the initial interrupt affinity
setup, so the interrupt might be routed to a different node.
Restrict the default affinity mask to the node on which the irq
descriptor is allocated.
[ tglx: Massaged changelog ]
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1332788538-17425-1-git-send-email-prarit@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The only place irq_finalize_oneshot() is called with force parameter set
is the threaded handler error exit path. But IRQTF_RUNTHREAD is dropped
at this point and irq_wake_thread() is not going to set it again,
since PF_EXITING is set for this thread already. So irq_finalize_oneshot()
will drop the threads bit in threads_oneshot anyway and hence the force
parameter is superfluous.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120321162234.GP24806@dhcp-26-207.brq.redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
exit_irq_thread() clears IRQTF_RUNTHREAD flag and drops the thread's bit in
desc->threads_oneshot then. The bit must not be set again in between and it
does not, since irq_wake_thread() sees PF_EXITING flag first and returns.
Due to above the order or checking PF_EXITING and IRQTF_RUNTHREAD flags in
irq_wake_thread() is important. This change just makes it more visible in the
source code.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120321162212.GO24806@dhcp-26-207.brq.redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ruGA
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irq_domain support for all architectures from Grant Likely:
"Generialize powerpc's irq_host as irq_domain
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
dt: fix twl4030 for non-dt compile on x86
mfd: twl-core: Add IRQ_DOMAIN dependency
devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
irq_domain: Centralize definition of irq_dispose_mapping()
irq_domain/mips: Allow irq_domain on MIPS
irq_domain/x86: Convert x86 (embedded) to use common irq_domain
ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
irq_domain/microblaze: Convert microblaze to use irq_domains
irq_domain/powerpc: Replace custom xlate functions with library functions
irq_domain/powerpc: constify irq_domain_ops
irq_domain/c6x: Use library of xlate functions
irq_domain/c6x: constify irq_domain structures
irq_domain/c6x: Convert c6x to use generic irq_domain support.
irq_domain: constify irq_domain_ops
irq_domain: Create common xlate functions that device drivers can use
irq_domain: Remove irq_domain_add_simple()
irq_domain: Remove 'new' irq_domain in favour of the ppc one
mfd: twl-core.c: Fix the number of interrupts managed by twl4030
of/address: add empty static inlines for !CONFIG_OF
irq_domain: Add support for base irq and hwirq in legacy mappings
...
Pull perf events changes for v3.4 from Ingo Molnar:
- New "hardware based branch profiling" feature both on the kernel and
the tooling side, on CPUs that support it. (modern x86 Intel CPUs
with the 'LBR' hardware feature currently.)
This new feature is basically a sophisticated 'magnifying glass' for
branch execution - something that is pretty difficult to extract from
regular, function histogram centric profiles.
The simplest mode is activated via 'perf record -b', and the result
looks like this in perf report:
$ perf record -b any_call,u -e cycles:u branchy
$ perf report -b --sort=symbol
52.34% [.] main [.] f1
24.04% [.] f1 [.] f3
23.60% [.] f1 [.] f2
0.01% [k] _IO_new_file_xsputn [k] _IO_file_overflow
0.01% [k] _IO_vfprintf_internal [k] _IO_new_file_xsputn
0.01% [k] _IO_vfprintf_internal [k] strchrnul
0.01% [k] __printf [k] _IO_vfprintf_internal
0.01% [k] main [k] __printf
This output shows from/to branch columns and shows the highest
percentage (from,to) jump combinations - i.e. the most likely taken
branches in the system. "branches" can also include function calls
and any other synchronous and asynchronous transitions of the
instruction pointer that are not 'next instruction' - such as system
calls, traps, interrupts, etc.
This feature comes with (hopefully intuitive) flat ascii and TUI
support in perf report.
- Various 'perf annotate' visual improvements for us assembly junkies.
It will now recognize function calls in the TUI and by hitting enter
you can follow the call (recursively) and back, amongst other
improvements.
- Multiple threads/processes recording support in perf record, perf
stat, perf top - which is activated via a comma-list of PIDs:
perf top -p 21483,21485
perf stat -p 21483,21485 -ddd
perf record -p 21483,21485
- Support for per UID views, via the --uid paramter to perf top, perf
report, etc. For example 'perf top --uid mingo' will only show the
tasks that I am running, excluding other users, root, etc.
- Jump label restructurings and improvements - this includes the
factoring out of the (hopefully much clearer) include/linux/static_key.h
generic facility:
struct static_key key = STATIC_KEY_INIT_FALSE;
...
if (static_key_false(&key))
do unlikely code
else
do likely code
...
static_key_slow_inc();
...
static_key_slow_inc();
...
The static_key_false() branch will be generated into the code with as
little impact to the likely code path as possible. the
static_key_slow_*() APIs flip the branch via live kernel code patching.
This facility can now be used more widely within the kernel to
micro-optimize hot branches whose likelihood matches the static-key
usage and fast/slow cost patterns.
- SW function tracer improvements: perf support and filtering support.
- Various hardenings of the perf.data ABI, to make older perf.data's
smoother on newer tool versions, to make new features integrate more
smoothly, to support cross-endian recording/analyzing workflows
better, etc.
- Restructuring of the kprobes code, the splitting out of 'optprobes',
and a corner case bugfix.
- Allow the tracing of kernel console output (printk).
- Improvements/fixes to user-space RDPMC support, allowing user-space
self-profiling code to extract PMU counts without performing any
system calls, while playing nice with the kernel side.
- 'perf bench' improvements
- ... and lots of internal restructurings, cleanups and fixes that made
these features possible. And, as usual this list is incomplete as
there were also lots of other improvements
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (120 commits)
perf report: Fix annotate double quit issue in branch view mode
perf report: Remove duplicate annotate choice in branch view mode
perf/x86: Prettify pmu config literals
perf report: Enable TUI in branch view mode
perf report: Auto-detect branch stack sampling mode
perf record: Add HEADER_BRANCH_STACK tag
perf record: Provide default branch stack sampling mode option
perf tools: Make perf able to read files from older ABIs
perf tools: Fix ABI compatibility bug in print_event_desc()
perf tools: Enable reading of perf.data files from different ABI rev
perf: Add ABI reference sizes
perf report: Add support for taken branch sampling
perf record: Add support for sampling taken branch
perf tools: Add code to support PERF_SAMPLE_BRANCH_STACK
x86/kprobes: Split out optprobe related code to kprobes-opt.c
x86/kprobes: Fix a bug which can modify kernel code permanently
x86/kprobes: Fix instruction recovery on optimized path
perf: Add callback to flush branch_stack on context switch
perf: Disable PERF_SAMPLE_BRANCH_* when not supported
perf/x86: Add LBR software filter support for Intel CPUs
...
Alexander pointed out that the warnons in the regular exit path are
bogus and the thread_mask one actually could be triggered when
__setup_irq() hands out that thread_mask again after __free_irq()
dropped irq_desc->lock.
Thinking more about it, neither IRQTF_RUNTHREAD nor the bit in
thread_mask can be set as this is the regular exit path. We come here
due to:
__free_irq()
remove action from desc
synchronize_irq()
kthread_stop()
So synchronize_irq() makes sure that the thread finished running and
cleaned up both the thread_active count and thread_mask. After that
point nothing can set IRQTF_RUNTHREAD on this action. So the warnons
and the cleanups are pointless.
Reported-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Ido Yariv <ido@wizery.com>
Link: http://lkml.kernel.org/r/20120315190755.GA6732@dhcp-26-207.brq.redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current implementation does not always flush the threaded handler
when disabling the irq. In case the irq handler was called, but the
threaded handler hasn't started running yet, the interrupt will be
flagged as pending, and the handler will not run. This implementation
has some issues:
First, if the interrupt is a wake source and flagged as pending, the
system will not be able to suspend.
Second, when quickly disabling and re-enabling the irq, the threaded
handler might continue to run after the irq is re-enabled without the
irq handler being called first. This might be an unexpected behavior.
In addition, it might be counter-intuitive that the threaded handler
will not be called even though the irq handler was called and returned
IRQ_WAKE_THREAD.
Fix this by always waiting for the threaded handler to complete in
synchronize_irq().
[ tglx: Massaged comments, added WARN_ONs and the missing
IRQTF_RUNTHREAD check in exit_irq_thread() ]
Signed-off-by: Ido Yariv <ido@wizery.com>
Link: http://lkml.kernel.org/r/1322843052-7166-1-git-send-email-ido@wizery.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently IRQTF_DIED flag is set when a IRQ thread handler calls do_exit()
But also PF_EXITING per process flag gets set when a thread exits. This
fix eliminates the duplicate by using PF_EXITING flag.
Also, there is a race condition in exit_irq_thread(). In case a thread's
bit is cleared in desc->threads_oneshot (and the IRQ line gets unmasked),
but before IRQTF_DIED flag is set, a new interrupt might come in and set
just cleared bit again, this time forever. This fix throws IRQTF_DIED flag
away, eliminating the race as a result.
[ tglx: Test THREAD_EXITING first as suggested by Oleg ]
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120309135958.GD2114@dhcp-26-207.brq.redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since 63706172f3 kthread_stop() is not
afraid of dead kernel threads. So no need to check if a thread is
alive before stopping it. These checks still were racy.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120309135939.GC2114@dhcp-26-207.brq.redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When a new thread handler is created, an irqaction is passed to it as
data. Not only that irqaction is stored in task_struct by the handler
for later use, but also a structure associated with the kernel thread
keeps this value as long as the thread exists.
This fix kicks irqaction out off task_struct. Yes, I introduce new bit
field. But it allows not only to eliminate the duplicate, but also
shortens size of task_struct.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120309135925.GB2114@dhcp-26-207.brq.redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xommit ac5637611(genirq: Unmask oneshot irqs when thread was not woken)
fails to unmask when a !IRQ_ONESHOT threaded handler is handled by
handle_level_irq.
This happens because thread_mask is or'ed unconditionally in
irq_wake_thread(), but for !IRQ_ONESHOT interrupts never cleared. So
the check for !desc->thread_active fails and keeps the interrupt
disabled.
Keep the thread_mask zero for !IRQ_ONESHOT interrupts.
Document the thread_mask magic while at it.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Reported-and-tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In 2008, commit 0c5d1eb77a ("genirq: record trigger type") modified the
way set_irq_type() handles the 'no trigger' condition. However, this has
an adverse effect on PCMCIA support on Intel StrongARM and probably PXA
platforms.
PCMCIA has several status signals on the socket which can trigger
interrupts; some of these status signals depend on the card's mode
(whether it is configured in memory or IO mode). For example, cards have
a 'Ready/IRQ' signal: in memory mode, this provides an indication to
PCMCIA that the card has finished its power up initialization. In IO
mode, it provides the device interrupt signal. Other status signals
switch between on-board battery status and loud speaker output.
In classical PCMCIA implementations, where you have a specific socket
controller, the controller provides a method to mask interrupts from the
socket, and importantly ignore any state transitions on the pins which
correspond with interrupts once masked. This masking prevents unwanted
events caused by the removal and application of socket power being
forwarded.
However, on platforms where there is no socket controller, the PCMCIA
status and interrupt signals are routed to standard edge-triggered GPIOs.
These GPIOs can be configured to interrupt on rising edge, falling edge,
or never. This is where the problems start.
Edge triggered interrupts are required to record events while disabled via
the usual methods of {free,request,disable,enable}_irq() to prevent
problems with dropped interrupts (eg, the 8390 driver uses disable_irq()
to defer the delivery of interrupts). As a result, these interfaces can
not be used to implement the desired behaviour.
The side effect of this is that if the 'Ready/IRQ' GPIO is disabled via
disable_irq() on suspend, and enabled via enable_irq() after resume, we
will record the state transitions caused by powering events as valid
interrupts, and foward them to the card driver, which may attempt to
access a card which is not powered up.
This leads delays resume while drivers spin in their interrupt handlers,
and complaints from drivers before they realize what's happened.
Moreover, in the case of the 'Ready/IRQ' signal, this is requested and
freed by the card driver itself; the PCMCIA core has no idea whether the
interrupt is requested, and, therefore, whether a call to disable_irq()
would be valid. (We tried this around 2.4.17 / 2.5.1 kernel era, and
ended up throwing it out because of this problem.)
Therefore, it was decided back in around 2002 to disable the edge
triggering instead, resulting in all state transitions on the GPIO being
ignored. That's what we actually need the hardware to do.
The commit above changes this behaviour; it explicitly prevents the 'no
trigger' state being selected.
The reason that request_irq() does not accept the 'no trigger' state is
for compatibility with existing drivers which do not provide their desired
triggering configuration. The set_irq_type() function is 'new' and not
used by non-trigger aware drivers.
Therefore, revert this change, and restore previously working platforms
back to their former state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux@arm.linux.org.uk
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes IRQ_DOMAIN usable on MIPS. It uses an ugly workaround
to preserve current behaviour so that MIPS has time to add irq_domain
registration to the irq controller drivers. The workaround will be
removed in Linux v3.6
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Make irq_domain_ops pointer a constant to make it safer for multiple
instances to share the same ops pointer and change the irq_domain code
so that it does not modify the ops.
v4: Fix mismatched type reference in powerpc code
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Rather than having each interrupt controller driver creating its own barely
unique .xlate function for irq_domain, create a library of translators which
any driver can use directly.
v5: - Remove irq_domain_xlate_pci(). It was incorrect.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
irq_domain_add_simple() was a stop-gap measure until complete irq_domain
support was complete. This patch removes the irq_domain_add_simple()
interface.
This patch also drops the explicit irq_domain initialization performed
by the mach-versatile code because the versatile interrupt controller
already has irq_domain support built into it. This was a bug that was
hanging around quietly for a while, but with the full irq_domain which
actually verifies that irq_domain ranges are available it would cause
the registration to fail and the system wouldn't boot.
v4: Fixed number of irqs in mx5 gpio code
v2: Updated to pass in host_data pointer on irq_domain allocation.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Olof Johansson <olof@lixom.net>
This patch removes the simplistic implementation of irq_domains and enables
the powerpc infrastructure for all irq_domain users. The powerpc
infrastructure includes support for complex mappings between Linux and
hardware irq numbers, and can manage allocation of irq_descs.
This patch also converts the few users of irq_domain_add()/irq_domain_del()
to call irq_domain_add_legacy() instead.
v3: Fix bug that set up too many irqs in translation range.
v2: Fix removal of irq_alloc_descs() call in gic driver
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Add support for a legacy mapping where irq = (hwirq - first_hwirq + first_irq)
so that a controller driver can allocate a fixed range of irq_descs and use
a simple calculation to translate back and forth between linux and hw irq
numbers. This is needed to use an irq_domain with many of the ARM interrupt
controller drivers that manage their own irq_desc allocations. Ultimately
the goal is to migrate those drivers to use the linear revmap, but doing it
this way allows each driver to be converted separately which makes the
migration path easier.
This patch generalizes the IRQ_DOMAIN_MAP_LEGACY method to use
(first_irq-first_hwirq) as the offset between hwirq and linux irq number,
and adds checks to make sure that the hwirq number does not exceed range
assigned to the controller.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
No functional changes. Replaces non-exported references to 'host' with domain.
Does not change any symbol names referenced by other .c files.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
zero always means no irq when using irq domains. Get rid of the NO_IRQ
references.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch only moves the code. It doesn't make any changes, and the
code is still only compiled for powerpc. Follow-on patches will generalize
the code for other architectures.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
An interrupt might be pending when irq_startup() is called, but the
startup code does not invoke the resend logic. In some cases this
prevents the device from issuing another interrupt which renders the
device non functional.
Call the resend function in irq_startup() to keep things going.
Reported-and-tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the primary handler of an interrupt which is marked IRQ_ONESHOT
returns IRQ_HANDLED or IRQ_NONE, then the interrupt thread is not
woken and the unmask logic of the interrupt line is never
invoked. This keeps the interrupt masked forever.
This was not noticed as most IRQ_ONESHOT users wake the thread
unconditionally (usually because they cannot access the underlying
device from hard interrupt context). Though this behaviour was nowhere
documented and not necessarily intentional. Some drivers can avoid the
thread wakeup in certain cases and run into the situation where the
interrupt line s kept masked.
Handle it gracefully.
Reported-and-tested-by: Lothar Wassmann <lw@karo-electronics.de>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Part of the series to unify the irq remapping mechanisms in the
kernel. A follow up patch will copy the powerpc implementation into
kernel/irq/irqdomain.c, which will be a lot easier if the structures
are identical.
Where they differ, I've chose to use the powerpc names since there is
a lot more code using those names.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
irq_domain printk's too much. Drop some output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Olof Johansson <olof@lixom.net>
The __raise_softirq_irqoff() contains a tracepoint. As tracepoints in headers
can cause issues, and not to mention, bloats the kernel when they are
in a static inline, it is best to move the function that contains the
tracepoint out of the header and into softirq.c.
Link: http://lkml.kernel.org/r/20120118120711.GB14863@elte.hu
Suggested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
On ARM, we don't want SPARSE_IRQ to be a user visible option. Make
SPARSE_IRQ visible based on MAY_HAVE_SPARSE_IRQ instead of depending
on HAVE_SPARSE_IRQ.
With this, SPARSE_IRQ is not visible on C6X and ARM.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CI17
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
devicetree/next changes queued for v3.3 merge window
* tag 'devicetree-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
ARM: prom.h: Fix build error by removing unneeded header file
irq: check domain hwirq range for DT translate
dt: add empty of_get_node/of_put_node functions
of/pdt: fix section mismatch warning
i2c-designware: add OF binding support
dt/i2c: Enumerate some of the known trivial i2c devices
dt: reform for_each_property to for_each_property_of_node
ARM/of: allow *machine_desc.dt_compat to be const
of/base: Take NULL string into account for property with multiple strings
OF/device-tree: Add some entries to vendor-prefixes.txt
Fix up trivial add-add conflicts in include/linux/of.h
A DT node may have more than 1 domain associated with it, so make sure
the hwirq number is within range when doing DT translation.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
irqdomain support is used in interrupt controller drivers that may not
have device tree support but only need the basic HW->Linux irq
translation. Rather than having each of these implement their own IRQ
domain, allow them to use the simple ops.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In irq_wait_for_interrupt(), the should_stop member is verified before
setting the task's state to TASK_INTERRUPTIBLE and calling schedule().
In case kthread_stop sets should_stop and wakes up the process after
should_stop is checked by the irq thread but before the task's state
is changed, the irq thread might never exit:
kthread_stop irq_wait_for_interrupt
------------ ----------------------
...
... while (!kthread_should_stop()) {
kthread->should_stop = 1;
wake_up_process(k);
wait_for_completion(&kthread->exited);
...
set_current_state(TASK_INTERRUPTIBLE);
...
schedule();
}
Fix this by checking if the thread should stop after modifying the
task's state.
[ tglx: Simplified it a bit ]
Signed-off-by: Ido Yariv <ido@wizery.com>
Link: http://lkml.kernel.org/r/1322740508-22640-1-git-send-email-ido@wizery.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Commit fa27271bc8d2("genirq: Fixup poll handling") introduced a
regression that broke irqfixup/irqpoll for some hardware configurations.
Amidst reorganizing 'try_one_irq', that patch removed a test that
checked for 'action->handler' returning IRQ_HANDLED, before acting on
the interrupt. Restoring this test back returns the functionality lost
since 2.6.39. In the current set of tests, after 'action' is set, it
must precede '!action->next' to take effect.
With this and my previous patch to irq/spurious.c, c75d720fca, all
IRQ regressions that I have encountered are fixed.
Signed-off-by: Edward Donovan <edward.donovan@numble.net>
Reported-and-tested-by: Rogério Brito <rbrito@ime.usp.br>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org (2.6.39+)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The power management functions related to interrupts do not know
(yet) about per-cpu interrupts and end up calling the wrong
low-level methods to enable/disable interrupts.
This leads to all kind of interesting issues (action taken on one
CPU only, updating a refcount which is not used otherwise...).
The workaround for the time being is simply to flag these interrupts
with IRQF_NO_SUSPEND. At least on ARM, these interrupts are actually
dealt with at the architecture level.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1321446459-31409-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
commit d05c65fff0 ("genirq: spurious: Run only one poller at a time")
introduced a regression, leaving the boot options 'irqfixup' and
'irqpoll' non-functional. The patch placed tests in each function, to
exit if the function is already running. The test in 'misrouted_irq'
exited when it should have proceeded, effectively disabling
'misrouted_irq' and 'poll_spurious_irqs'.
The check for an already running poller needs to be "!= 1" not "== 1"
as "1" is the value when the first poller starts running.
Signed-off-by: Edward Donovan <edward.donovan@numble.net>
Cc: maciej.rutecki@gmail.com
Link: http://lkml.kernel.org/r/1320175784-6745-1-git-send-email-edward.donovan@numble.net
Cc: stable@vger.kernel.org # >= 2.6.39
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
Recent commit "irq: Track the owner of irq descriptor" in
commit ID b6873807a7 placed module.h into linux/irq.h
but we are trying to limit module.h inclusion to just C files
that really need it, due to its size and number of children
includes. This targets just reversing that include.
Add in the basic "struct module" since that is all we really need
to ensure things compile. In theory, b687380 should have added the
module.h include to the irqdesc.h header as well, but the implicit
module.h everywhere presence masked this from showing up. So give
it the "struct module" as well.
As for the C files, irqdesc.c is only using THIS_MODULE, so it
does not need module.h - give it export.h instead. The C file
irq/manage.c is now (as of b687380) using try_module_get and
module_put and so it needs module.h (which it already has).
Also convert the irq_alloc_descs variants to macros, since all
they really do is is call the __irq_alloc_descs primitive.
This avoids including export.h and no debug info is lost.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting <linux/module.h> via an implicit non-obvious
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Interrupt controllers can have non-zero starting value for h/w irq numbers.
Adding support in irq_domain allows the domain hwirq numbering to match
the interrupt controllers' numbering.
As this makes looping over irqs for a domain more complicated, add loop
iterators to iterate over all hwirqs and irqs for a domain.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
h8300: Move gpio.h to gpio-internal.h
gpio: pl061: add DT binding support
gpio: fix build error in include/asm-generic/gpio.h
gpiolib: Ensure struct gpio is always defined
irq: Add EXPORT_SYMBOL_GPL to function of irq generic-chip
gpio-ml-ioh: Use NUMA_NO_NODE not GFP_KERNEL
gpio-pch: Use NUMA_NO_NODE not GFP_KERNEL
gpio: langwell: ensure alternate function is cleared
gpio-pch: Support interrupt function
gpio-pch: Save register value in suspend()
gpio-pch: modify gpio_nums and mask
gpio-pch: support ML7223 IOH n-Bus
gpio-pch: add spinlock in suspend/resume processing
gpio-pch: Delete invalid "restore" code in suspend()
gpio-ml-ioh: Fix suspend/resume issue
gpio-ml-ioh: Support interrupt function
gpio-ml-ioh: Delete unnecessary code
gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler()
gpio/nomadik: use genirq core to track enablement
gpio/nomadik: disable clocks when unused
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add IRQF_RESUME_EARLY and resume such IRQs earlier
genirq: Fix fatfinered fixup really
genirq: percpu: allow interrupt type to be set at enable time
genirq: Add support for per-cpu dev_id interrupts
genirq: Add IRQCHIP_SKIP_SET_WAKE flag
Some functions of irq generic-chip is undefined, because
EXPORT_SYMBOL_GPL is not set to these.
ERROR: "irq_setup_generic_chip" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_alloc_generic_chip" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_setup_generic_chip" [drivers/gpio/gpio-ml-ioh.ko] undefined!
ERROR: "irq_alloc_generic_chip" [drivers/gpio/gpio-ml-ioh.ko] undefined!
This is revised that EXPORT_SYMBOL_GPL can be added and referred
to in functions.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds a mechanism to resume selected IRQs during syscore_resume
instead of dpm_resume_noirq.
Under Xen we need to resume IRQs associated with IPIs early enough
that the resched IPI is unmasked and we can therefore schedule
ourselves out of the stop_machine where the suspend/resume takes
place.
This issue was introduced by 676dc3cf5b "xen: Use IRQF_FORCE_RESUME".
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1318713254.11016.52.camel@dagon.hellion.org.uk
Cc: stable@kernel.org (at least to 2.6.32.y)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As request_percpu_irq() doesn't allow for a percpu interrupt to have
its type configured (it is generally impossible to configure it on all
CPUs at once), add a 'type' argument to enable_percpu_irq().
This allows some low-level, board specific init code to be switched to
a generic API.
[ tglx: Added WARN_ON argument ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ARM GIC interrupt controller offers per CPU interrupts (PPIs),
which are usually used to connect local timers to each core. Each CPU
has its own private interface to the GIC, and only sees the PPIs that
are directly connect to it.
While these timers are separate devices and have a separate interrupt
line to a core, they all use the same IRQ number.
For these devices, request_irq() is not the right API as it assumes
that an IRQ number is visible by a number of CPUs (through the
affinity setting), but makes it very awkward to express that an IRQ
number can be handled by all CPUs, and yet be a different interrupt
line on each CPU, requiring a different dev_id cookie to be passed
back to the handler.
The *_percpu_irq() functions is designed to overcome these
limitations, by providing a per-cpu dev_id vector:
int request_percpu_irq(unsigned int irq, irq_handler_t handler,
const char *devname, void __percpu *percpu_dev_id);
void free_percpu_irq(unsigned int, void __percpu *);
int setup_percpu_irq(unsigned int irq, struct irqaction *new);
void remove_percpu_irq(unsigned int irq, struct irqaction *act);
void enable_percpu_irq(unsigned int irq);
void disable_percpu_irq(unsigned int irq);
The API has a number of limitations:
- no interrupt sharing
- no threading
- common handler across all the CPUs
Once the interrupt is requested using setup_percpu_irq() or
request_percpu_irq(), it must be enabled by each core that wishes its
local interrupt to be delivered.
Based on an initial patch by Thomas Gleixner.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some irq chips need the irq_set_wake() functionality, but do not
require a irq_set_wake() callback. Instead of forcing an empty
callback to be implemented add a flag which notes this fact. Check for
the flag in set_irq_wake_real() and return success when set.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
If an irq_chip provides .irq_shutdown(), but neither of .irq_disable() or
.irq_mask(), free_irq() crashes when jumping to NULL.
Fix this by only trying .irq_disable() and .irq_mask() if there's no
.irq_shutdown() provided.
This revives the symmetry with irq_startup(), which tries .irq_startup(),
.irq_enable(), and irq_unmask(), and makes it consistent with the comment for
irq_chip.irq_shutdown() in <linux/irq.h>, which says:
* @irq_shutdown: shut down the interrupt (defaults to ->disable if NULL)
This is also how __free_irq() behaved before the big overhaul, cfr. e.g.
3b56f0585f ("genirq: Remove bogus conditional"),
where the core interrupt code always overrode .irq_shutdown() to
.irq_disable() if .irq_shutdown() was NULL.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Link: http://lkml.kernel.org/r/1315742394-16036-2-git-send-email-geert@linux-m68k.org
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit f3637a5f2e.
It turns out that this breaks several drivers, one example being OMAP
boards which use the on-board OMAP UARTs and the omap-serial driver that
will not boot to userspace after the commit.
Paul Walmsley reports that enabling CONFIG_DEBUG_SHIRQ reveals 'IRQ
handler type mismatch' errors:
IRQ handler type mismatch for IRQ 74
current handler: serial idle
...
and the reason is that setting IRQF_ONESHOT will now result in those
interrupt handlers having different IRQF flags, and thus being
unsharable. So the commit log in the reverted commit:
"Since it is required for those users and
there is no difference for others it makes sense to add this flag
unconditionally."
is simply not true: there may not be any difference from a "actions at
irq time", but there is a *big* difference wrt this flag testing irq
management (see __setup_irq() in kernel/irq/manage.c).
One solution may be to stop verifying IRQF_ONESHOT in __setup_irq(), but
right now the safe course of action is to revert the change. Let's
revisit this in a later merge window.
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-doc warning in irqdesc.c:
Warning(kernel/irq/irqdesc.c:353): No description found for parameter 'owner'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Track the owner of irq descriptor
irq: Always set IRQF_ONESHOT if no primary handler is specified
genirq: Fix wrong bit operation
Interrupt descriptors can be allocated from modules. The interrupts
are used by other modules, but we have no refcount on the module which
provides the interrupts and there is no way to establish one on the
device level as the interrupt using module is agnostic to the fact
that the interrupt is provided by a module rather than by some builtin
interrupt controller.
To prevent removal of the interrupt providing module, we can track the
owner of the interrupt descriptor, which also provides the relevant
irq chip functions in the irq descriptor.
request/setup_irq() can now acquire a refcount on the owner module to
prevent unloading. free_irq() drops the refcount.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/20110711101731.GA13804@Chamillionaire.breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If no primary handler is specified then a default one is assigned
which always returns IRQ_WAKE_THREAD. This handler requires the
IRQF_ONESHOT flag on LEVEL / EIO typed irqs because the source of
interrupt is not disabled. Since it is required for those users and
there is no difference for others it makes sense to add this flag
unconditionally.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/1310070737-18514-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_domain_generate_simple() is an easy way to generate an irq translation
domain for simple irq controllers. It assumes a flat 1:1 mapping from
hardware irq number to an offset of the first linux irq number assigned
to the controller
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
devres uses the pointer value as key after it's freed, which is safe but
triggers spurious use-after-free warnings on some static analysis tools.
Rearrange code to avoid such warnings.
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Reviewed-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In kernel/irq/manage.c::irq_set_irq_wake() we call
irq_get_desc_buslock() which may return NULL, but the code
dereferences the result unconditionally.
irq_set_irq_wake() has lots of callers - I checked a few and I couldn't
find anything that guarantees that they won't call it with some input that
will cause irq_get_desc_buslock() to return NULL, so I think it's a good
thing to test and -EINVAL was the most sane error code in this situation
that I could think of.
Not all callers test the return value of irq_set_irq_wake(), but those
that do take != 0 to mean error as far as I can see, so they should be
fine. I guess those that don't test actually should, but that's a
different issue.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1106092300360.17868@swampdragon.chaosbits.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds