commit 4956e10903 ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Cc: stable@vger.kernel.org
Fixes: 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik...")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD card specification allows cards to error out a SWITCH command
where the requested function in a group is not supported. The spec
provides for a set of capabilities which indicate which functions are
supported.
In the case of the power limit, requesting an unsupported power level
via the SWITCH command fails, resulting in the power level remaining at
the power-on default of 0.72W, even though the host and card may support
higher powers levels.
This has been seen with SanDisk 8GB cards, which support the default
0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host,
supporting up to 2.88W (800mA). This currently causes us to try to set
a power limit function value of '3' (2.88W) which the card errors out
on, and thereby causes the power level to remain at 0.72W rather than
the desired 1.44W.
Arrange to limit the selected current limit by the capabilities reported
by the card to avoid the SWITCH command failing. Select the highest
current limit that the host and card combination support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: a39ca6ae0a ("mmc: core: Simplify and fix for SD switch processing")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The misc control register is 32bit wide, the used readw/writew
accessors only mainipulate the low 16bit of this register. It
currently doesn't matter as all the bit changed are located in
the lower half, but together with the u32 variable used to hold
the contents of the register it is seriously confusing.
Switch to 32bit accessors to avoid any future breakage.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Keep the quirk bits, as Tegra30 and Tegra114 host have different levels
of support for UHS-I modes and so need different spare bits to be set,
but change the logic to be positive.
Tegra210 needs a different tuning sequence than Tegra30+. Disable
UHS modes until support for this is properly added.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the UHS tuning sequence in a similar way to the one
contained in the TRM. It deviates in the way how to check if the tap
value is passing, by using the common Linux MMC function, which does
not only check for data CRC errors, but also if the received block
pattern is correct.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Tegra30 and up TRM states that this bit should always be
programmed to 0 by driver software.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow the the driver to change the clock supplied from the CAR directly,
minimizing the need to divide the clock inside the SDMMC module itself.
This allows for higher clock speeds than the default 48MHz supplied to
the module and is a prerequisite to support DDR signaling modes, where
the Tegra host needs to be run with a fixed internal divider of 2 for
data to be sampled correctly. (Tegra K1 TRM v03p chapter 29.7.1.1)
Also enable the broken preset value quirk as the preset values need to
be adapted to the changed clocking. While Tegra114+ allows this through
vendor registers, there is no such way for Tegra30. Takes the easy way
out and keep things consistent between the different SoC generations by
flagging the preset registers as unusable.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 52221610dd ("mmc: sdhci: Improve external VDD regulator
support"), for the VDD is supplied via external regulators, we ignore
the code to convert a VDD voltage request into one of the standard
SDHCI voltage levels, then program it in the SDHCI_POWER_CONTROL. This
brings two issues:
1. SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON quirk isn't handled properly any
more.
2. What's more, once SDHCI_POWER_ON bit is set, some controllers such
as the sdhci-pxav3 used in marvell berlin SoCs require the voltage
levels programming in the SDHCI_POWER_CONTROL register, even the VDD
is supplied by external regulator. So the host in marvell berlin SoCs
still works fine after the commit. However, commit 3cbc6123a9 ("mmc:
sdhci: Set SDHCI_POWER_ON with external vmmc") sets the SDHCI_POWER_ON
bit, this would make the host in marvell berlin SoCs won't work any
more with external vmmc.
This patch restores the behavior when setting VDD through external
regulator by moving the call of mmc_regulator_set_ocr() to the end
of sdhci_set_power() function.
After this patch, the sdcard on Marvell Berlin SoC boards work again.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 52221610dd ("mmc: sdhci: Improve external VDD ...")
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A card can be removed while it is runtime suspended.
Do not print an error message.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is quite common for Android devices to utilize more
then 8 partitions on internal eMMC storage.
The vanilla kernel can support this via
CONFIG_MMC_BLOCK_MINORS, however that solution caps the
system to 256 minors total, which limits the number of
mmc cards the system can support.
This patch, which has been carried for quite awhile in
the AOSP common tree, provides an alternative solution
that doesn't seem to limit the total card count. So I
wanted to submit it for consideration upstream.
This patch sets the GENHD_FL_EXT_DEVT flag, which will
allocate minor number in major 259 for partitions past
disk->minors.
It also removes the use of disk_devt to determine devidx
from md->disk. md->disk->first_minor is always initialized
from devidx and can always be used to recover it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Austin S Hemmelgarn <ahferroin7@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Colin Cross <ccross@android.com>
[jstultz: Added context to commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc workqueue is an ordered workqueue, allowing only one work to
execute per given time. As this workqueue is used for card detection, the
conseqeunce is that cards will be detected one by one waiting for each
other.
Moreover, most of the time spent during card initialization is waiting for
the card's internal firmware to be ready. From a CPU perspective this
typically means waiting for a completion variable to be kicked via an
IRQ-handler or waiting for a sleep timer to finish.
This behaviour of detecting/initializing cards is sub-optimal, especially
for SOCs having several controllers/cards.
Let's convert to use the system_freezable_wq for the mmc detect works.
This enables several works to be executed simultaneously and thus also
cards to be detected like so.
Tests on UX500, which holds two eMMC cards and an SD-card (actually also
an SDIO card, currently not detected), shows a significant improved
behaviour due to this change.
Before this change, both the eMMC cards waited for the SD card to be
initialized as its detect work entered the workqueue first. In some cases,
depending on the characteristic of the SD-card, they got delayed 1-1.5 s.
Additionally for the second eMMC, it needed to wait for the first eMMC to
be initialized which added another 120-190 ms.
Converting to the system_freezable_wq, removed these delays and made both
the eMMC cards available far earlier in the boot sequence.
Selecting the system_freezable_wq, in favour of for example the system_wq,
is because we need card detection mechanism to be disabled once userspace
are frozen during system PM. Currently the mmc core deal with this via PM
notifiers, but following patches may utilize the behaviour of the
system_freezable_wq, to simplify the use of the PM notifiers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Alan Cooper <alcooperx@gmail.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a time window between __mmc_send_status() and time_afer(),
on some eMMC chip, the timeout_ms is only 10ms, if this thread was
scheduled out during this period, then, even card has already changes
to transfer state by the result of CMD13, this part of code also treat
it to timeout error.
So, need calculate timeout first, then call __mmc_send_status(), if
already timeout and card still in programing state, then treat it to
the real timeout error.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug
print") fixed one NULL pointer dereference but unfortunately introduced
another. "data" may be NULL if this is a command timeout for a command
without any data, so we should only use it if we're actually waiting for
data.
Fixes: bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug print")
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no primary handler is specified for threaded_irq then a
default one is assigned which always returns IRQ_WAKE_THREAD.
This handler requires the IRQF_ONESHOT, because the source of
interrupt is not disabled
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there are too many error logs shown when use CMD21/CMD19 to do tune,
and it will appear at each resume time, print out so many logs to the
uart console cost too mush time. so change it to dev_dbg.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition dependency between devices. This patch
enables MMC/SD/SDIO card and SDIO function devices to suspend/resume
asynchronously. This will take advantage of multicore and improve
system suspend/resume speed. After applying this patch and enabling
all SDIO function's child devices to suspend/resume asynchronously
on ASUS T100TA, the system suspend-to-idle time is reduced from
1645ms to 1108ms, and the system resume time is reduced from 940ms
to 918ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a legacy facility to prevent runtime suspend if the
bus power is on. This is needed in cases where the power to
the card is dependent on the bus power. It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off(). These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem. In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume. So remove the check.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The version 3.00 SDHCI spec. was a bit unclear about the
required data alignment for 64-bit DMA, whereas the version
4.10 spec. uses different language and indicates that only
4-byte alignment is required rather than the 8-byte alignment
currently implemented. That make no difference to SD and EMMC
which invariably transfer data in sector-aligned blocks.
However with SDIO, it results in using more DMA descriptors
than necessary. Theoretically that slows DMA slightly although
DMA is not the limiting factor for throughput, so there is no
discernable impact on performance. Nevertheless, the driver
should follw the spec unless there is good reason not to, so
this patch corrects the alignment criterion.
There is a more complicated criterion for the DMA descriptor
table itself. However the table is allocated by dma_alloc_coherent()
which allocates pages (i.e. aligned to a page boundary).
For simplicity just check it is 8-byte aligned, but add a comment
that some Intel controllers actually require 8-byte alignment
even when using 32-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI has built-in DMA called ADMA2. ADMA2 uses a descriptor
table to define DMA scatter-gather. Each desciptor can specify
a data length up to 65536 bytes, however the length field is
only 16-bits so zero means 65536. Consequently, putting zero
when the size is zero must not be allowed. This patch fixes
one case where zero data length could be set inadvertently.
The problem happens because unaligned data gets split and the
code did not consider that the remaining aligned portion might
be zero length. That case really only happens for SDIO because
SD and eMMC cards transfer blocks that are invariably sector-
aligned. For SDIO, access to function registers is done by
data transfer (CMD53) when the register is bigger than 1 byte.
Generally registers are 4 bytes but 2-byte registers are possible.
So DMA of 4 bytes or less can happen. When 32-bit DMA is used,
the data alignment must be 4, so 4-byte transfers won't casue a
problem, but a 2-byte transfer could. However with the introduction
of 64-bit DMA, the data alignment for 64-bit DMA was made 8 bytes,
so all 4-byte transfers not on 8-byte boundaries get "split" into
a 4-byte chunk and a 0-byte chunk, thereby hitting the bug.
In fact, a closer look at the SDHCI specs indicates that only the
descriptor table requires 8-byte alignment for 64-bit DMA. That
will be dealt with in a separate patch, but the potential for a
2-byte access remains, so this fix is needed anyway.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage. However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd. Fix by passing the card's
ocr value which does not have the flag.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver may not be able to set the power correctly but that
is not a reason to BUG().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In some cases, the stronger 33 Ohm driver strength must not be used
so it is not a suitable default. Change it to the standard default
50 Ohm value.
The patch applies to v4.2+ except the file name changed. It is
drivers/mmc/host/sdhci-pci.c prior to v.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit cc4f414c88 ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode. While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch introduce a new MMC_CAP2_NO_SDIO cap used to tell the mmc
core to not send SDIO specific commands.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are no in-kernel users of the MVSDIO platform data method
(instantiating from a board file) so just delete this code and
make this a DT-only driver. We depend on OF and check that we have
an OF node in probe().
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform data struct is only used inside the MVSDIO driver,
nowhere else in the entire kernel. Move the struct into the
driver and delete the external header.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
u32 vvn;
vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
if (vvn == VENDOR_V_22)
host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
if (vvn > VENDOR_V_22)
host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}
This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Fixes: f4932cfd22 ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The atmci_convert_chksize() function is no more valid for controller
version 0x600 due to the introduction of '2 data' chunk size.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
atmel-mci-regs.h is only included in atmel-mci.c so move its content in
the driver and do some cleanup in these definitions to remove checkpatch
errors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc pm notifiers were recently reworked, but the new
code produces a lot of warnings when CONFIG_PM_SLEEP is disabled:
In file included from ../drivers/mmc/core/sdio_bus.c:27:0:
drivers/mmc/core/core.h:97:13: warning: 'mmc_register_pm_notifier' defined but not used [-Wunused-function]
The obvious solution is to add the 'inline' keyword at the
function definition, as it should be for any function defined
in a header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0e40be7c20e0 ("mmc: core: Refactor code to register the MMC PM notifier")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here we use '|=' to set the tuning-step, but before that, we should
clear the tuning-step, otherwise we could got the wrong setting.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When compiling the sh_mmcif driver for ARM64, we currently
get a harmless build warning:
../drivers/mmc/host/sh_mmcif.c: In function 'sh_mmcif_request_dma_one':
../drivers/mmc/host/sh_mmcif.c:417:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_tx :
^
../drivers/mmc/host/sh_mmcif.c:418:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_rx;
This could be worked around by adding another cast to uintptr_t, but
I decided to simplify the code a little more to avoid that. This
splits out the platform data using code into a separate function
and builds that only for CONFIG_SUPERH. This part still has a typecast
but does not need a second one. The SH platform code could be further
modified to pass a pointer directly as we do on other architectures
when we have a filter function.
The normal case is simplified further and now just calls
dma_request_slave_channel() directly without going through the
compat handling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a trivial patch which fixes printed strings split across two
or more lines in the source. I tried to grep for some error output*,
but I couldn't find it easily because it was broken across multiple
lines. This patch makes my life easier.
* in particular "Timeout waiting for hardware interrupt."
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_pwrseq_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data in the SoC description structures is static and can therefore
reside in read-only memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add runtime PM support and use runtime_force_suspend|resume() for system
PM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmalloc instead of kzalloc, as zeroing the memory isn't needed.
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turn the informative message about no vmmc/vqmmc regulator found in
debug one. There is no need to indicate that something optional is
missing. Moreover, it can bring confusion, people who doesn't know
it is optional may consider these messages as warnings or errors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
_mmc_detect_card_removed() validates that the card is removable, but when
being called via the bus_ops ->detect() callbacks, the validation is
redundant as it's already done in mmc_rescan().
Move the validation of a removable card to the mmc_detect_card_removed()
API, which is where it's applicable, to allow the blk error recovery path
to get the response a bit earlier.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of checking for "#ifdef" directly in the code, let's invent a pair
of mmc core functions to deal with register/unregister the MMC PM notifier
block. Implement stubs for these functions when CONFIG_PM_SLEEP is unset,
as in that case the PM notifiers isn't used.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.
In mmc_rescan(), the ->card_event() and the ->get_cd() callback are being
invoked without claiming the host, let's fix this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->card_event() callback may be called when re-scan is disabled and for
non-removable cards, which both cases are unnecessary.
Instead let's move the call later in mmc_rescan() where these constraints
have been validated.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver will not probe without valid DMA channels so no need to check
if they are valid when the module is removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Anytime a write operation is performed with Reliable Write flag enabled,
the eMMC device is enforced to bypass the cache and do a write to the
underling NVM device by Jedec specification; this causes a performance
penalty since write operations can't be optimized by the device cache.
In our tests, we replayed a typical mobile daily trace pattern and found
~9% overall time reduction in trace replay by using this patch. Also the
write ops within 4KB~64KB chunk size range get a 40~60% performance
improvement by using the patch (as this range of write chunks are the ones
affected by REQ_META).
This patch has been discussed in the Mobile & Embedded Linux Storage Forum
and it's the results of feedbacks from many people. We also checked with
fsdevl and f2fs mailing list developers that this change in the usage of
REQ_META is not affecting FS behavior and we got positive feedbacks.
Reporting here the feedbacks:
http://comments.gmane.org/gmane.linux.file-systems/97219http://thread.gmane.org/gmane.linux.file-systems.f2fs/3178/focus=3183
Signed-off-by: Bruce Ford <bford@micron.com>
Signed-off-by: Luca Porzio <lporzio@micron.com>
Fixes: ce39f9d17c ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/mtk-sd.c: In function ‘get_best_delay’:
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.start’ is used uninitialized in this function
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.maxlen’ is used uninitialized in this function
If delay is zero, these fields are indeed not initialized.
Let the compiler preinitialize the whole struct to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400() calls __mmc_switch() which checks the switch is
successful using CMD13 (SEND_STATUS). The problem is that it does that
using the timing settings of the previous mode. That is prone to error,
especially when switching from HS to HS400 because the timing parameters
for HS mode are tighter than the timing parameters for HS400 mode.
In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.
However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs400() can be made more
reliable by setting the host to the correct timing before sending CMD13.
This patch does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the mmc_switch_status() function in preparation for calling it
in mmc_select_hs400().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400() begins with the card and host in HS200 mode.
Therefore, any commands sent to the card should use HS200 timing.
It is incorrect to set the host to High Speed (HS) timing before
sending the switch command. Doing so is unreliable because
the timing parameters for HS mode are tighter than the timing
parameters for HS200 mode. Thus the HS timings should be set
only after the card has switched mode.
However, it is not unreasonable first to reduce the frequency to
the HS mode frequency, which should make the switch command and
subsequent CMD13 commands more reliable.
This patch does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently mmc_select_hs200() uses __mmc_switch() which checks the
success of the switch to HS200 mode using CMD13 (SEND_STATUS).
The problem is that it does that using the timing settings of legacy
mode. That is prone to error, not least because the timing parameters
for legacy mode are tighter than the timing parameters for HS200 mode.
In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.
However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs200() can be made more
reliable by setting the host to the correct timing before sending CMD13.
This patch does that.
A complication is that the caller, mmc_select_timing(), will ignore a
switch error (indicated by -EBADMSG), assume the old mode is valid
and continue, so the old timing must be restored in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit converting pxamci to slot-gpio API inverted the logic of the
read-only gpio. Fix it by inverting the logic again.
Fixes: fd546ee6a7 ("mmc: pxamci: fix card detect with slot-gpio API")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
When card is running with DDR mode, dwmmc needs to set DDR_REG bit at
UHS_REG register.
Before this patch, dwmmc controller doesn't consider this.
If this patch is not applied, CRC or other error shoulds be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to DesignWare DoC file, CardThreshold bit should be
bit[27:16].
So it's correct to use (0xFFF << 16), not (0x1FFF << 16).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "host->dms->ch" pointer is NULL here so we can't use it to print the
error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pwrseq_emmc driver does a eMMC card reset before a system reboot to
allow broken or limited ROM boot-loaders (that don't have an eMMC reset
logic) to be able to read the second stage from the eMMC.
But this has to be called before a system reboot handler and while most
of them use the priority 128, there are other restart handlers (such as
the syscon-reboot one) that use a higher priority. So, use the highest
priority to make sure that the eMMC hw is reset before a system reboot.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even if we only use one gpd, we need alloc 2 gpd and make
the gpd->next pointer to the second gpd, or may get gpd checksum
error, this was checked by hardware
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use the ios->timing directly is better
It can reflect current timing and do settings by timing
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable omap_hsmmc for Keystone 2 architecture which reuses the HSMMC
IP found on OMAP platforms.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ACPI HIDs for Intel host controllers including one
supporting HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add some macros for HCON register operations
to make code more readable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC doesn't have a standard power control register, so when
writing this register in stack we should do nothing to avoid
incorrect operation.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There's little sense in releasing the host on mmc_add_card() error
immediately after reclaiming it, so reclaim the host only in case
of success.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This algorithm will try 1 degree increments, since there's no way to tell
what resolution the underlying phase code uses. As an added bonus, doing
many tunings yields better results since some tests are run more than once
(ex: if the underlying driver uses 45 degree increments, the tuning code
will try the same angle more than once).
It will then construct a list of good phase ranges (even ranges that cross
360/0), will pick the biggest range then it will set the sample_clk to the
middle of that range.
We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time (ex 10
degrees) this will not work with the current clock phase framework (which
floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.
If a device has device specific code (like exynos) then that will still
take precedence, otherwise this new code will execute. If the device wants
to tune, but has no sample_clk defined we'll return EIO with an error
message.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've introduced a new helper in the MMC core:
mmc_regulator_set_vqmmc(). Let's use this in dw_mmc. Using this new
helper has some advantages:
1. We get the mmc_regulator_set_vqmmc() behavior of trying to match
VQMMC and VMMC when the signal voltage is 3.3V. This ensures max
compatibility.
2. We get rid of a few more warnings when probing unsupported
voltages.
3. We get rid of some non-dw_mmc specific code in dw_mmc.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds logic to the MMC core to set VQMMC. This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.
A few notes:
* When setting the signal voltage to 3.3V we do our best to make VQMMC
and VMMC match. It's been reported that this makes some old cards
happy since they were tested back in the day before UHS when VQMMC
and VMMC were provided by the same regulator. A nice side effect of
this is that we don't end up on the hairy edge of VQMMC (2.7V),
which some EEs claim is a little too close to the minimum for
comfort.
This is done in two steps. At first we try to find a VQMMC within
a 0.3V tolerance of VMMC and if this is not supported by the
supplying regulator we try to find a suitable voltage within the
whole 2.7V-3.6V area of the spec.
* The two step approach is currently necessary, as the used
regulator_set_voltage_triplet(min, target, max) uses a simple
implementation that just tries two basic steps:
regulator_set_voltage(target, max);
regulator_set_voltage(min, target);
So with only one step with 2.7-3.6V borders, if a suitable voltage
is a bit below VMMC, we would directly get the lowest 2.7V
which some boards (like Rockchips) don't like at all.
* When setting the signal voltage to 1.8V or 1.2V we aim for that
specific voltage instead of picking the lowest one in the range.
* We very purposely don't print errors in mmc_regulator_set_vqmmc().
There are cases where the MMC core will try several different
voltages and we don't want to pollute the logs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will shortly need the calculation of an ocr-bit to the actual
voltage in a second place too, so move it from mmc_regulator_set_ocr
to a common function mmc_ocrbitnum_to_vdd to make that possible.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.
Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.
To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Freescale eSDHC driver now supports both little-endian and
big-endian mode eSDHC IPs for ARM and PPC. So, MMC_SDHCI_OF_ESDHC
option needs to be reconfigured.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add another PCI ID for an Intel eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci-pci-core.c:447:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.
- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to hardware spec, validate DDR50 mode
for SDXC.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD19 tuning is also available for DDR50 mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As SD Specifications Part1 Physical Layer Specification Version
3.01 says, CMD19 tuning is available for unlocked cards in transfer
state of 1.8V signaling mode. The small difference between v3.00
and 3.01 spec means that CMD19 tuning is also available for DDR50
mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_IOC_CMD and MMC_IOC_MULTI_CMD ioctl() code currently bails on
any eMMC errors. However, in case there is any resp[] data, we
should attempt to copy resp[] back to user space. The user app
can then determine which command(s) failed in the MMC_IOC_MULTI_CMD
case AND/OR report better diagnostics in both cases.
Gwendal Grignou provided the idea and it was previously implemented
and tested on v3.18 ChromeOS kernel:
https://chromium-review.googlesource.com/#/c/299956
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hyung Taek Ryoo <hryoo@nvidia.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: David Riley <davidriley@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add MMC_TIMING_UHS_SDR12 and MMC_TIMING_UHS_SDR25
for mmc_ios_show to show the ios->timing if mmc card runs under
these two modes.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some sdio wifi modules have not been working reliable with the sunxi-mmc
host code. This turns out to be caused by starting new io-rw commands while
the card signals that it is still busy processing a previous command.
This commit adds card-busy detection to the sunxi-mmc driver which together
with recent core changes to check card-busy before starting io-rw commands
fixes the wifi reliability issues on the Cubietruck and other sunxi boards
using sdio wifi.
Reported-by: Eugene K <sigintmailru@gmail.com>
Suggested-by: Eugene K <sigintmailru@gmail.com>
Cc: Eugene K <sigintmailru@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some sdio wifi chips will not work properly if we try to start new
sdio-rw requests while the device is signalling that it is busy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a helper function to check if an opcode is a sd-io-rw-* opcode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain eMMC devices allow vendor specific device information to be read
via a sequence of vendor commands. These vendor commands must be issued
in sequence and an atomic fashion. One way to support this would be to
add an ioctl function for sending a sequence of commands to the device
atomically as proposed here. These multi commands are simple array of
the existing mmc_ioc_cmd structure.
The structure passed via the ioctl uses a __u64 type to specify the number
of commands (so that the structure is aligned on a 64-bit boundary) and a
zero length array as a header for list of commands to be issued. The
maximum number of commands that can be sent is determined by
MMC_IOC_MAX_CMDS (which defaults to 255 and should be more than
sufficient).
This based upon work by Seshagiri Holi <sholi@nvidia.com>.
Signed-off-by: Seshagiri Holi <sholi@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The simple power sequence provider sets a value for multiple GPIOs in one
go so it is better to use the API already provided by the GPIO descriptor
API instead of open coding the same logic.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_CAP_RUNTIME_RESUME support to save resume time
Drop unnecessary SDC_ARG write
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add ios->drv_type for mmc_ios_show to show the
card's driver type.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The goto is correct and the unreachable "return -EINVAL" should be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_init() will clear all irqs and set the needed irqs. So
logically sdhci_init() should be called before request irq.
If not, some irqs may be triggled and handled wrongly. Take
the following into consideration, after request irq, if
SDIO card interrupt enabled, a sd card in the sd slot will
trigger a mass of interrupt(SDHCI_INT_CARD_INT), because at
this time, the vmmc-regulator still not restore, no voltage
supply for the sd card, so the pin of data0~data3 change and
keep low, interrupt(SDHCI_INT_CARD_INT) will rise up ceaselessly.
Due to we already reguest irq, system will be busy in handling
this endless irq, can't response to other event.
So we should call sdhci_init() before request irq in sd resume.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver prints if the data width is 8-bit but it's using a
binary OR instead of a binary AND so it will always report as
"is_8bit=Y" regardless of the flags in host->mmc->caps.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The gpiod_get() function expands to gpiod_get_index() with index 0
so it's better to use it since is easier to read and more concise.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As there are no users of the __mmc_switch() API, except for the mmc core
itself, let's convert it from an exported function into an internal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.
In some code paths for SDIO, particularly related to the PM support,
mmc_power_off|up() is invoked without keeping the host claimed. Let's fix
these.
Moreover, mmc_start|stop_host() also invokes mmc_power_off|up() without
claiming the host, let's fix these as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add an entry to the sdhci_acpi_uids list to detect the SD card
reader on the Asus X205Ta laptop.
dstd table:
Device (SDHC)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "PNP0FFF") // _HID: Hardware ID
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SD Card Controller - 80860F16") // _DDN: DOS Dev
Name (_UID, 0x03) // _UID: Unique ID
Name (RDEP, Package (0x02)
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs the
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk. Without it, the
internal clock could never stabilised when changing the sd clock
frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock
Control Register to 0 before computing the new value and writing it.
It disables the internal clock which causes a reset mecanism. If we
write the new value before this reset mecanism is done, it will prevent
the stabilisation of the internal clock, so a delay is needed. This
delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is
used.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of armada_38x_quirks error, all clocks should be cleaned-up, same
as after mv_conf_mbus_windows failure.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to 'FE-2946959' erratum the clock inversion option is
needed to support slow frequencies when the card input hold time
requirement is high. This setting is not required for high speed
MMC and might cause timing violation.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
shci-pxav3 driver is enabling by default the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not
required for Armada 38x and leads to wrong clock setting in the divider.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Starting with commit 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc") MMC on omap3 stopped working
for legacy booting.
This is because legacy booting sets up some of the resource in the
platform init code, and for optional regulators always seem to
return -EPROBE_DEFER for the legacy booting.
Let's fix the issue by checking for device tree based booting for
now. Then when omap3 boots in device tree only mode, this patch
can be just reverted.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c55d7a0553.
Without reverting this commit we get "unbalanced disables for pbias_mmc_omap4"
errors on omap4430. It seems that 4430 and 4460 behave in a different way for
the PBIAS regulator registers and until that has been debugged further we
cannot rely on the regulator status registers in hardare on 4430.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21
to do tune, assume there were 10 clock phase need to try, phase 0 to
phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so
the last CMD19/CMD21 will get CRC error, host->need_retune was set and
cause mmc_retune was called, then dead loop of mmc_retune
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move pxamci to mmc slot-gpio API to fix interrupt request.
It fixes the case where the card detection is on a gpio expander, on I2C
for example on zylonite board. In this case, the card detect netsted
interrupt is called from a threaded interrupt. The request_irq() fails,
because a hard irq cannot be a nested interrupt from a threaded
interrupt (set __setup_irq()).
This was tested on zylonite and mioa701 boards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.
As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Fixes: 16b23787fc ("mmc: sdhci-of-arasan: Call OF parsing for MMC")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
- Fix a race condition in the request handling
- Skip trim commands for some buggy kingston eMMCs
- An optimization and a correction for erase groups
- Set CMD23 quirk for some Sandisk cards
MMC host:
- sdhci: Give GPIO CD higher precedence and don't poll when it's used
- sdhci: Fix DMA memory leakage
- sdhci: Some updates for clock management
- sdhci-of-at91: introduce driver for the Atmel SDMMC
- sdhci-of-arasan: Add support for sdhci-5.1
- sdhci-esdhc-imx: Add support for imx7d which also supports HS400
- sdhci: A collection of fixes and improvements for various sdhci hosts
- omap_hsmmc: Modernization of the regulator code
- dw_mmc: A couple of fixes for DMA and PIO mode
- usdhi6rol0: A few fixes and support probe deferral for regulators
- pxamci: Convert to use dmaengine
- sh_mmcif: Fix the suspend process in a short term solution
- tmio: Adjust timeout for commands
- sunxi: Fix timeout while gating/ungating clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wR1C
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix a race condition in the request handling
- Skip trim commands for some buggy kingston eMMCs
- An optimization and a correction for erase groups
- Set CMD23 quirk for some Sandisk cards
MMC host:
- sdhci: Give GPIO CD higher precedence and don't poll when it's used
- sdhci: Fix DMA memory leakage
- sdhci: Some updates for clock management
- sdhci-of-at91: introduce driver for the Atmel SDMMC
- sdhci-of-arasan: Add support for sdhci-5.1
- sdhci-esdhc-imx: Add support for imx7d which also supports HS400
- sdhci: A collection of fixes and improvements for various sdhci hosts
- omap_hsmmc: Modernization of the regulator code
- dw_mmc: A couple of fixes for DMA and PIO mode
- usdhi6rol0: A few fixes and support probe deferral for regulators
- pxamci: Convert to use dmaengine
- sh_mmcif: Fix the suspend process in a short term solution
- tmio: Adjust timeout for commands
- sunxi: Fix timeout while gating/ungating clock"
* tag 'mmc-v4.3' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: android-goldfish: remove incorrect __iomem annotation
mmc: core: fix race condition in mmc_wait_data_done
mmc: host: omap_hsmmc: remove CONFIG_REGULATOR check
mmc: host: omap_hsmmc: use ios->vdd for setting vmmc voltage
mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias status
mmc: host: omap_hsmmc: enable/disable vmmc_aux regulator based on previous state
mmc: host: omap_hsmmc: don't use ->set_power to set initial regulator state
mmc: host: omap_hsmmc: avoid pbias regulator enable on power off
mmc: host: omap_hsmmc: add separate function to set pbias
mmc: host: omap_hsmmc: add separate functions for enable/disable supply
mmc: host: omap_hsmmc: return error if any of the regulator APIs fail
mmc: host: omap_hsmmc: remove unnecessary pbias set_voltage
mmc: host: omap_hsmmc: use mmc_host's vmmc and vqmmc
mmc: host: omap_hsmmc: use the ocrmask provided by the vmmc regulator
mmc: host: omap_hsmmc: cleanup omap_hsmmc_reg_get()
mmc: host: omap_hsmmc: return on fatal errors from omap_hsmmc_reg_get
mmc: host: omap_hsmmc: use devm_regulator_get_optional() for vmmc
mmc: sdhci-of-at91: fix platform_no_drv_owner.cocci warnings
mmc: sh_mmcif: Fix suspend process
mmc: usdhi6rol0: fix error return code
...
Pull SG updates from Jens Axboe:
"This contains a set of scatter-gather related changes/fixes for 4.3:
- Add support for limited chaining of sg tables even for
architectures that do not set ARCH_HAS_SG_CHAIN. From Christoph.
- Add sg chain support to target_rd. From Christoph.
- Fixup open coded sg->page_link in crypto/omap-sham. From
Christoph.
- Fixup open coded crypto ->page_link manipulation. From Dan.
- Also from Dan, automated fixup of manual sg_unmark_end()
manipulations.
- Also from Dan, automated fixup of open coded sg_phys()
implementations.
- From Robert Jarzmik, addition of an sg table splitting helper that
drivers can use"
* 'for-4.3/sg' of git://git.kernel.dk/linux-block:
lib: scatterlist: add sg splitting function
scatterlist: use sg_phys()
crypto/omap-sham: remove an open coded access to ->page_link
scatterlist: remove open coded sg_unmark_end instances
crypto: replace scatterwalk_sg_chain with sg_chain
target/rd: always chain S/G list
scatterlist: allow limited chaining without ARCH_HAS_SG_CHAIN
Pull core block updates from Jens Axboe:
"This first core part of the block IO changes contains:
- Cleanup of the bio IO error signaling from Christoph. We used to
rely on the uptodate bit and passing around of an error, now we
store the error in the bio itself.
- Improvement of the above from myself, by shrinking the bio size
down again to fit in two cachelines on x86-64.
- Revert of the max_hw_sectors cap removal from a revision again,
from Jeff Moyer. This caused performance regressions in various
tests. Reinstate the limit, bump it to a more reasonable size
instead.
- Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
Most devices have huge trim limits, which can cause nasty latencies
when deleting files. Enable the admin to configure the size down.
We will look into having a more sane default instead of UINT_MAX
sectors.
- Improvement of the SGP gaps logic from Keith Busch.
- Enable the block core to handle arbitrarily sized bios, which
enables a nice simplification of bio_add_page() (which is an IO hot
path). From Kent.
- Improvements to the partition io stats accounting, making it
faster. From Ming Lei.
- Also from Ming Lei, a basic fixup for overflow of the sysfs pending
file in blk-mq, as well as a fix for a blk-mq timeout race
condition.
- Ming Lin has been carrying Kents above mentioned patches forward
for a while, and testing them. Ming also did a few fixes around
that.
- Sasha Levin found and fixed a use-after-free problem introduced by
the bio->bi_error changes from Christoph.
- Small blk cgroup cleanup from Viresh Kumar"
* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
blk: Fix bio_io_vec index when checking bvec gaps
block: Replace SG_GAPS with new queue limits mask
block: bump BLK_DEF_MAX_SECTORS to 2560
Revert "block: remove artifical max_hw_sectors cap"
blk-mq: fix race between timeout and freeing request
blk-mq: fix buffer overflow when reading sysfs file of 'pending'
Documentation: update notes in biovecs about arbitrarily sized bios
block: remove bio_get_nr_vecs()
fs: use helper bio_add_page() instead of open coding on bi_io_vec
block: kill merge_bvec_fn() completely
md/raid5: get rid of bio_fits_rdev()
md/raid5: split bio for chunk_aligned_read
block: remove split code in blkdev_issue_{discard,write_same}
btrfs: remove bio splitting and merge_bvec_fn() calls
bcache: remove driver private bio splitting code
block: simplify bio_add_page()
block: make generic_make_request handle arbitrarily sized bios
blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
block: don't access bio->bi_error after bio_put()
block: shrink struct bio down to 2 cache lines again
...
The following panic is captured in ker3.14, but the issue still exists
in latest kernel.
---------------------------------------------------------------------
[ 20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference
at virtual address 00000578
......
[ 20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60
[ 20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60
[ 20.740134] c0 3136 (Compiler) Call trace:
[ 20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60
[ 20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54
[ 20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34
[ 20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220
[ 20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264
[ 20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158
[ 20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4
[ 20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0
[ 20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac
[ 20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c
----------------------------------------------------------------------
Because in SMP, "mrq" has race condition between below two paths:
path1: CPU0: <tasklet context>
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
//
// If CPU0 has just finished "is_done_rcv = true" in path1, and at
// this moment, IRQ or ICache line missing happens in CPU0.
// What happens in CPU1 (path2)?
//
// If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode:
// path2 would have chance to break from wait_event_interruptible
// in mmc_wait_for_data_req_done and continue to run for next
// mmc_request (mmc_blk_rw_rq_prep).
//
// Within mmc_blk_rq_prep, mrq is cleared to 0.
// If below line still gets host from "mrq" as the result of
// compiler, the panic happens as we traced.
wake_up_interruptible(&mrq->host->context_info.wait);
}
path2: CPU1: <The mmcqd thread runs mmc_queue_thread>
static int mmc_wait_for_data_req_done(...
{
...
while (1) {
wait_event_interruptible(context_info->wait,
(context_info->is_done_rcv ||
context_info->is_new_req));
static void mmc_blk_rw_rq_prep(...
{
...
memset(brq, 0, sizeof(struct mmc_blk_request));
This issue happens very coincidentally; however adding mdelay(1) in
mmc_wait_data_done as below could duplicate it easily.
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
+ mdelay(1);
wake_up_interruptible(&mrq->host->context_info.wait);
}
At runtime, IRQ or ICache line missing may just happen at the same place
of the mdelay(1).
This patch gets the mmc_context_info at the beginning of function, it can
avoid this race condition.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 2220eedfd7 ("mmc: fix async request mechanism ....")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that support for platforms which have optional regulator is added,
remove CONFIG_REGULATOR check in omap_hsmmc.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
vdd voltage is set in mmc core to ios->vdd and vmmc should actually
be set to this voltage. Modify omap_hsmmc_enable_supply
to not take vdd as argument since now it's directly set to
the voltage in ios->vdd.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use regulator_is_enabled of pbias regulator to find pbias regulator
status instead of maintaining a custom bookkeeping
pbias_enabled variable.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enable vmmc_aux regulator only if it is in disabled state and disable
vmmc_aux regulator only if it is in enabled state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the regulator is enabled on boot (checked using regulator_is_enabled),
invoke regulator_enable() so that the usecount reflects the correct
state of the regulator and then disable the regulator so that the
initial state of the regulator is disabled. Avoid using ->set_power,
since set_power also takes care of setting the voltages which is not
needed at this point.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix omap_hsmmc_set_power so that pbias regulator is not enabled
during power off.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions to set pbias and invoke it from omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions for enable/disable supply and invoke it from
omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return error if any of the regulator APIs (regulator_enable,
regulator_disable, regulator_set_voltage) fails in
omap_hsmmc_set_power to avoid undefined behavior.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the unnecessary pbias regulator_set_voltage done after
pbias regulator_disable in omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Instead of using omap_hsmmc_host's vcc and vcc_aux
members, use vmmc and vqmmc present in mmc_host which is present
for the same purpose.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the vmmc regulator provides a valid ocrmask, use it. By this even if
the pdata has a valid ocrmask, it will be overwritten with the ocrmask
of the vmmc regulator.
Also remove the unnecessary compatibility check between the ocrmask in
the pdata and the ocrmask from the vmmc regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Instead of using a local regulator variable
in omap_hsmmc_reg_get() for holding the return value of
devm_regulator_get_optional() and then assigning to omap_hsmmc_host
regulator members: vcc, vcc_aux and pbias, directly use the
omap_hsmmc_host regulator members.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now return error only if the return value of
devm_regulator_get_optional() is not the same as -ENODEV, since with
-EPROBE_DEFER, the regulator can be obtained later and all other
errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since vmmc can be optional for some platforms, use
devm_regulator_get_optional() for vmmc. Now return error only
if the return value of devm_regulator_get_optional() is not the
same as -ENODEV, since with -EPROBE_DEFER, the regulator can be
obtained later and all other errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: ludovic.desroches@atmel.com <ludovic.desroches@atmel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock should be enable when SDHI registers are accessed.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Propagate error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intent appears to be to clear only the bits which are set in status
(by setting them to zero in the ack write), like in the other interrupt
handlers, and not to always clear everything (by always writing zero).
Use the correct not operator.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->sg is only set when we're transferring multiple blocks. Check for
its availibility before dereferencing it in the timeout work debug
print.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We ignore errors from mmc_regulator_get_supply() because the usage of
the regulators is optional for the driver, but we still need to check
for and handle EPROBE_DEFER, like it's done in for example dw_mmc.
Otherwise we might end up not using the specified regulators just
because of probe order.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the compatible string in sdhci-of-arasan.c to
support sdhci-arasan5.1 version of controller. No documented
controller IP version is found in the TRM, so we use ths version
of command queueing engine integrated into this controller by arasan
to specify our controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bb8175a8aa ("mmc: sdhci: clarify DDR timing mode between
SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be
distinguished from SD-UHS, but it missed setting driver type for
MMC_DDR52 timing mode.
So sometimes we get the following error on Marvell BG2Q DMP board:
[ 1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd
response 0x900, card status 0xb00
[ 1.569314] mmcblk0: retrying using single block read
[ 1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd
response 0x900, card status 0x0
[ 1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2
[ 1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd
response 0x900, card status 0x0
[ 1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3
This patches fixes this by adding the missing driver type setting.
Fixes: bb8175a8aa ("mmc: sdhci: clarify DDR timing mode ...")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 250ms timeout is too short.
On my system enabling the oclk takes under 50ms and disabling slightly
over 100ms when idle. Under load disabling the clock can take over
350ms.
This does not make mmc clock gating look like good option to have on
sunxi but the system should not crash with mmc clock gating enabled
nonetheless.
This patch sets the timeout to 750ms.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the current quirk set is for an old FPGA, and this patch corrects
quirks according to real SoC.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some mass production of kingston eMMCs which adopt Phison's
firmware will meet an unrecoverable data conrruption occasionally
if performing trim due to a firmware bug confirmed by vendor. We
found it on Intel-C3230RK platform. So we add fixup of broken trim
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.
For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.
This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.
This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.
So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.
So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For eSDHC(version < 2.3), the pre divider only could divide base clock
by 2 at least. Add workaround for this to avoid unexpected issue.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fixes: bd455029d0 ("mmc: sdhci-of-esdhc: Pre divider starts at 1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently one mrq->data maybe execute dma_map_sg() twice
when mmc subsystem prepare over one new request, and the
following log show up:
sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25
In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req
for the first time, and map another dma-memory(2) in sdhci_prepare_data
for the second time. But driver only unmap the dma-memory(2), and
dma-memory(1) never unmapped, which cause the dma memory leak issue.
This patch use another method to map the dma memory for the mrq->data
which can fix this dma memory leak issue.
Fixes: 348487cb28 ("mmc: sdhci: use pipeline mmc requests to improve performance")
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use more compact of_property_read_bool() calls instead of the
of_find_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes MMC not working issue on O2Micro/BayHub Host, which
requires transfer mode register to be cleared when sending no DMA
command.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When requesting a trim for several bytes, everything up to the next
erase-group is erased. This causes data corruption.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the problem which timeout occurs at the time of command request with
several cards.
The timeout value was insufficient as a verification of several cards,
so it was changed 5 seconds from 2 seconds.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In programmable mode, if the clock frequency is too high, the divider
can be too small to meet the clock frequency requirement especially to
init the SD card. In this case, switch to the divided clock mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[hch: split from a larger patch by Dan]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.
dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.
We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.
This means that host should get DRTO and DTO interrupt.
But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.
There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.
Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.
So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a
[ 4.991109] ------------[ cut here ]------------
[ 4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[ 4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM
because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.
Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
"ENOSYS means 'invalid syscall nr' and nothing else"
- split lines whose length is greater than 80 characters
- avoid quoted string split across lines
- use min_t instead of min, to fix warning message:
"min() should probably be min_t(int, cnt, host->part_buf_count)"
- fix missing a blank line after declarations
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.
On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.
In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.
Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.
What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Some Sandisk cards(such as "SDMB-32" and "SDM032" cards)
can't support CMD23, and would generate CMD timeout. So add
FIX-UP for these two types Sandisk cards.
Error log:
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC supports high speed mode, but has no enabling bit for it.
Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no pdata.set_power was set by the platform code, the driver
was updating pdata with its own fallback function. This is a no-no
since pdata shall be read-only.
This patch pushes the check 'pdata->set_power != NULL' down into
the fallback functions. If pdata.set_power is really set, it calls them
and exits, otherwise the fallback code is used.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to use polling for card detection state change when
drivers are using dedicated GPIO for this. Don't poll in this case.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller could have BROKEN_CARD_DETECTION quirk set, but drivers
could use GPIO to detect card present state. Let, when defined, GPIO
take precedence, so drivers could properly detect card state and not
use polling.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's excessive to use prefix for the parameters when you do
modprobe mmc-block mmcblk.perdev_minors=16
Make this available only for built-in case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch over pxamci to dmaengine. This prepares the devicetree full
support of pxamci.
This was successfully tested on a PXA3xx board, as well as PXA27x.
Signed-off-by: Daniel Mack <zonque@gmail.com>
[adapted to pxa-dma]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Walleij