Remove unnecessary static on local variable delt.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
5009 3456 576 9041 2351 drivers/media/rc/sir_ir.o
after:
text data bss dec hex filename
4988 3400 512 8900 22c4 drivers/media/rc/sir_ir.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no dependency between the two, so remove the dependency in
Kconfig files.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for CIR controller on MT7622 SoC. It has similar
handling logic as the previously MT7623 does, but there are some
differences in the register and field definition. So for ease portability
and maintenance, those differences all are being kept inside the platform
data as other drivers usually do. Currently testing successfully on NEC
and SONY remote controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch is the preparation patch in order to adapt into various
hardware through adding platform data which holds specific characteristics
and differences among MediaTek supported CIR devices instead of the old
way defining those data in the static way as macro has. And the existing
logic would be slightly changed to operate on those data which the actual
device depends on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The NEC decoder and the Sanyo decoders check if dev->keypressed is true
before calling rc_repeat (without holding dev->keylock).
Meanwhile, the XMP and JVC decoders do no such checks.
This patch makes sure all users of rc_repeat() do so consistently by
removing extra checks in NEC/Sanyo and modifying the check a bit in
rc_repeat() so that no input event is generated if the key isn't pressed.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit e8f4818895 ("[media] lirc: advertise
LIRC_CAN_GET_REC_RESOLUTION and improve") lircd uses the ioctl
LIRC_GET_REC_RESOLUTION to determine the shortest pulse or space that
the hardware can detect. This breaks decoding in lirc because lircd
expects the answer in microseconds, but nanoseconds is returned.
Cc: <stable@vger.kernel.org> # v2.6.36+
Reported-by: Derek <user.vdr@gmail.com>
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that rc_register_device() is reorganised, the dev->initialized
hack can be removed. Any driver which calls rc_register_device()
must be prepared for the device to go live immediately.
The dev->initialized commits that are relevant are commit c73bbaa4ec
("[media] rc-core: don't lock device at rc_register_device()") and
commit 08aeb7c9a4 ("[media] rc: add locking to fix register/show race").
The original problem was that show_protocols() would access
dev->rc_map.* and various other bits which are now properly
initialized before device_add() is called.
At the same time, remove the bogus "device is being removed" check.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device core infrastructure is based on the presumption that
once a driver calls device_add(), it must be ready to accept
userspace interaction.
This requires splitting rc_setup_rx_device() into two functions
and reorganizing rc_register_device() so that as much work
as possible is performed before calling device_add().
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This module was merged after commit 5a8fc6a3ce ("Annotate hardware
config module parameters in drivers/media/"), so add add the missing
hardware annotations.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ir-spi driver has 2 issues which prevents it from working with
lirc:
1. The ir-spi driver uses 16 bits of SPI data to create one cycle of
the waveform. As such our SPI clock needs to be 16x faster than the
carrier frequency.
The driver is inconsistent in how it currently handles this. It
initializes it to the carrier frequency:
But the commit message has some example code which initialises it
to 16x the carrier frequency:
val = 608000;
ret = ioctl(fd, LIRC_SET_SEND_CARRIER, &val);
To maintain compatibility with lirc, always do the frequency adjustment
in the driver.
2. lirc presents pulses in microseconds, but the ir-spi driver treats
them as cycles of the carrier. Similar to other lirc drivers, do the
conversion with DIV_ROUND_CLOSEST().
Fixes: fe052da492 ("[media] rc: add support for IR LEDs driven through SPI")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop a since commit e1159cb357 ("[media] mceusb: remove pointless
mce_flush_rx_buffer function") redundant reinitialisation of two urb
fields immediately after they have been initialised.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix urb and transfer-buffer leaks in an urb-submission error path which
may be hit when a device is disconnected.
Fixes: 66e89522af ("V4L/DVB: IR: add mceusb IR receiver driver")
Cc: stable <stable@vger.kernel.org> # 2.6.36
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=+jBV
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-2' into patchwork
media fixes for v4.12-rc4
* tag 'media/v4.12-2': (598 commits)
[media] rc-core: race condition during ir_raw_event_register()
[media] cec: drop MEDIA_CEC_DEBUG
[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER
[media] cec: select CEC_CORE instead of depend on it
[media] rainshadow-cec: ensure exit_loop is intialized
[media] atomisp: don't treat warnings as errors
Linux 4.12-rc3
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
PCI/msi: fix the pci_alloc_irq_vectors_affinity stub
blk-mq: Only register debugfs attributes for blk-mq queues
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Inlining these functions into the probe function makes it much
more readable.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These functions are too short and removing them makes the code more
readable.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several error paths do not free up resources. This simplifies the code
and fixes this.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the probe fails (e.g. port already in use), rmmod causes null deref.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Changing the protocol does not imply that the keymap changes.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The REP_DELAY setting on the input device is independent of hardware.
This change should not change how to driver works (as it does a
keydown/keyup and has no real repeat handling).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove superfluous includes and defines.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most drivers return both values when the device is gone.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The "debug" parameter isn't actually used anywhere.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
device_add() and friends already manage the references to the parent
device so these calls aren't necessary.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two functions only make the logic in lirc_register_driver()
harder to follow.
(Note that almost no other driver calls kobject_set_name() on their cdev
so I simply removed that part).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Merging the two means that lirc_allocate_buffer() is called before
device_add() and cdev_add() which makes more sense. This also
simplifies the locking slightly because lirc_allocate_buffer() will
always be called with lirc_dev_lock held.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Every caller of lirc_register_driver() passes their own fops and there
are no users of lirc_dev_fop_write() in the kernel tree. Thus we can
make fops mandatory and remove lirc_dev_fop_write().
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
out_sysfs is misleading, sysfs only comes into play after device_add().
Also, calling device_init() before the rest of struct dev is filled out
is clearer.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are no drivers which use this functionality.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since there are no users of this functionality, it can be removed
altogether.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drv->set_use_inc and drv->set_use_dec are already optional so we can
remove all dummy functions.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RX -EPIPE failure with infinite loop and flooding of
[ 2851.966506] mceusb 1-1.2:1.0: Error: urb status = -32
log message at 8000 messages per second.
Bug trigger appears to be normal, but heavy, IR receiver use.
Driver and Linux host become unusable after error.
Also seen at https://sourceforge.net/p/lirc/mailman/message/34886165/
Fix:
Message reports RX usb halt (stall) condition requiring usb_clear_halt()
call in non-interrupt context to recover. Add driver workqueue call to
perform this recovery based on method in use for the usbnet device driver.
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On the Amlogic SoCs, the bootloader firmware can handle the IR hardware
in order to Wake up or Power back the system when in suspend on
shutdown mode.
This patch switches the hardware configuration in a state usable by the
firmware to permit powering the system back.
Some vendor bootloader firmware were modified to switch to this
configuration but it may not be the case for all available products.
This patch was originally posted at [1].
[1] https://github.com/LibreELEC/linux-amlogic/pull/27
Signed-off-by: Alex Deryskyba <alex@codesnake.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch fixes meson-it driver by storing event without processing
to avoid losing key pressed events when system is loaded and events
are occurring too fast.
This issue was reported at [1]
[1] https://github.com/LibreELEC/linux-amlogic/pull/42
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Kconfig format is strict enough where if the indentation isn't
correct then the "make menuconfig" will break.
Fix the indentation to match all the other entries.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch the interrupt description to the default which is the of node
name. This is more in line with the interrupt descriptions in
other meson drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We don't need the memory barriers here and an interrupt handler should
be as fast as possible. Therefore switch to readl_relaxed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch to the managed versions of rc_allocate_device/rc_register_device,
thus simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make use of the bitfield macros thus partially hiding the complexity
of dealing with bitfields.
The patch also includes a minor fix to REG0_RATE_MASK, so far it was
set to bit 0..10, but according to the spec it's bit 0..11.
[mchehab@s-opensource.com: readd REG1_MODE_SHIFT and REG2_MODE_SHIFT
that got removed on the original patch, as this will be used on
another patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The irq number is used in the probe function only, therefore just use
a local variable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some dev_dbg messages are misleading. Some dev_dbg messages have
inconsistent formatting. mceusb_dev_printdata() prints incorrect range
of bytes (0 to len) in buffer which the driver will actually process next.
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Intermittent RX truncation and loss of IR received data. This resulted
in receive stream synchronization errors where driver attempted to
incorrectly parse IR data (eg 0x90 below) as command response.
[ 3969.139898] mceusb 1-1.2:1.0: processed IR data
[ 3969.151315] mceusb 1-1.2:1.0: rx data: 00 90 (length=2)
[ 3969.151321] mceusb 1-1.2:1.0: Unknown command 0x00 0x90
[ 3969.151336] mceusb 1-1.2:1.0: rx data: 98 0a 8d 0a 8e 0a 8e 0a 8e 0a 8e 0a 9a 0a 8e 0a 0b 3a 8e 00 80 41 59 00 00 (length=25)
[ 3969.151341] mceusb 1-1.2:1.0: Raw IR data, 24 pulse/space samples
[ 3969.151348] mceusb 1-1.2:1.0: Storing space with duration 500000
Bug trigger appears to be normal, but heavy, IR receiver use.
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A rc device can call ir_raw_event_handle() after rc_allocate_device(),
but before rc_register_device() has completed. This is racey because
rcdev->raw is set before rcdev->raw->thread has a valid value.
Cc: stable@kernel.org
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid warnings like those:
drivers/media/pci/ddbridge/ddbridge-core.c: In function 'dvb_input_detach':
drivers/media/pci/ddbridge/ddbridge-core.c:787:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (input->fe) {
^
drivers/media/pci/ddbridge/ddbridge-core.c:792:2: note: here
case 4:
^~~~
...
On several cases, it is just that gcc 7.1 is not capable of
understanding the comment, but on other places, we need an
annotation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc-7 suggests that an expression using a bitwise not and a bitmask
on a 'bool' variable is better written using boolean logic:
drivers/media/rc/imon.c: In function 'imon_incoming_scancode':
drivers/media/rc/imon.c:1725:22: error: '~' on a boolean expression [-Werror=bool-operation]
ictx->pad_mouse = ~(ictx->pad_mouse) & 0x1;
^
drivers/media/rc/imon.c:1725:22: note: did you mean to use logical not?
I agree.
Fixes: 21677cfc56 ("V4L/DVB: ir-core: add imon driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ir_lirc_register() currently creates its own lirc_buffer before
passing the lirc_driver to lirc_register_driver().
When a module is later unloaded, ir_lirc_unregister() gets called
which performs a call to lirc_unregister_driver() and then free():s
the lirc_buffer.
The problem is that:
a) there can still be a userspace app holding an open lirc fd
when lirc_unregister_driver() returns; and
b) the lirc_buffer contains "wait_queue_head_t wait_poll" which
is potentially used as long as any userspace app is still around.
The result is an oops which can be triggered quite easily by a
userspace app monitoring its lirc fd using epoll() and not closing
the fd promptly on device removal.
The minimalistic fix is to let lirc_dev create the lirc_buffer since
lirc_dev will then also free the buffer once it believes it is safe to
do so.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to input_register_device() needs to take place
before the repeat parameters are set or the input subsystem
repeat handling will be disabled (as was already noted in
the comments in that function).
Cc: stable <stable@vger.kernel.org> # v4.11
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since this driver does no detection of hardware, it might be used with
a non-sir port. Escape out if we are spinning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Gustavo A. R. Silva