Commit b70661c708 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes. Firstly,
the access size must correspond to the following rule:
(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
the above.
Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.
Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation. If neither, BUG(). This
exactly reflects the driver behaviour prior to the commit being fixed.
Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.
This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.
Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.
Fixes: b70661c708 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable lan91x adapters in some ARM machines and models
when booted with an ACPI kernel.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, mdiobus_alloc() sets the PHYs to polling mode, but a
pointer size memcpy means that a couple IRQs end up being overwritten
with a value of 0. This means that PHY_POLL is disabled and results
in unpredictable behavior depending on the PHY's location on the
MDIO bus. Remove that memcpy and the now unused phy_irq member to
force the SMSC911x PHYs into polling mode 100% of the time.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to use the generic DMA engine API in the smc911x
driver has led to a harmless warning about unused local variables:
smsc/smc911x.c: In function 'smc911x_probe':
smsc/smc911x.c:1796:20: error: unused variable 'param'
smsc/smc911x.c:1795:17: error: unused variable 'mask'
smsc/smc911x.c:1794:26: error: unused variable 'config'
This puts the variable declarations inside of the same #ifdef
that protects their use.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 79d3b59a93 ("net: smc911x: convert pxa dma to dmaengine")
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the dma transfers to be dmaengine based, now pxa has a dmaengine
slave driver. This makes this driver a bit more PXA agnostic.
The driver was only compile tested. The risk is quite small as no
current PXA platform I'm aware of is using smc911x driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver defines a macro that compares its argument to
itself, apparently to get a true result while using its argument
to avoid a warning about unused local variables.
Unfortunately, this triggers a warning with gcc-6, as the comparison
is obviously useless:
drivers/net/ethernet/smsc/smc91x.c: In function 'smc_hardware_send_pkt':
drivers/net/ethernet/smsc/smc91x.c:563:14: error: self-comparison always evaluates to true [-Werror=tautological-compare]
if (!smc_special_trylock(&lp->lock, flags)) {
This replaces the macro with another one that behaves similarly,
with a cast to (void) to ensure the argument is used, and using
a literal 'true' as its value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver doesn't honor the probe deferral mechanism when the
interrupt source is not yet available, such as one provided by a gpio
controller not probed.
Fix this by propagating the platform_get_irq() error code as the probe
return value.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware in certain situations loopback test fails and the
driver gets removed. During mdiobus_unregister() instance of PHY driver
gets disposed. But by this time it has already been started using
phy_connect_direct().
PHY driver uses DELAYED_WORK in order to maintain its state. Attempting
to dispose the driver without calling phy_disconnect() causes deallocation
of DELAYED_WORK being active. This shortly causes a bad crash in timer
code.
The problem can be discovered by enabling CONFIG_DEBUG_OBJECTS_TIMERS and
CONFIG_DEBUG_OBJECTS_FREE
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the dma transfers to be dmaengine based, now pxa has a dmaengine
slave driver. This makes this driver a bit more PXA agnostic.
The driver was tested on pxa27x (mainstone) and pxa310 (zylonite),
ie. only pxa platforms.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler may not be available when smsc911x probes if the
interrupt handler is a GPIO controller for example. Let's fix that
by adding handling for -EPROBE_DEFER.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62ee783bf1 ("smsc911x: Fix crash seen if neither ACPI nor OF is
configured or used") introduces an error check for the return value from
device_get_phy_mode() and bails out if there is an error. Unfortunately,
there are configurations where no phy is configured. Those configurations
now fail.
To fix the problem, accept error returns from device_get_phy_mode(),
and use the return value from device_property_read_u32() to determine
if there is a suitable firmware interface to read the configuration.
Fixes: 62ee783bf1 ("smsc911x: Fix crash seen if neither ACPI nor OF is configured or used")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No pr_dbg method exists.
While this code is #if 0'd, it'd be nicer to
use the generic hex_dump, so use it instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev==NULL check in smsc911x_probe_config is useless
and isn't providing any additional protection. If a fwnode
doesn't exist then an appropriate error should be returned
by device_get_phy_mode() covering the original case
of a missing of/fwnode.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0b50dc4fc9 ("Convert smsc911x to use ACPI as well as DT") makes
the call to smsc911x_probe_config() unconditional, and no longer fails if
there is no device node. device_get_phy_mode() is called unconditionally,
and if there is no phy node configured returns an error code. This error
code is assigned to phy_interface, and interpreted elsewhere in the code
as valid phy mode. This in turn causes qemu to crash when running a
variant of realview_pb_defconfig.
qemu: hardware error: lan9118_read: Bad reg 0x86
Fixes: 0b50dc4fc9 ("Convert smsc911x to use ACPI as well as DT")
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACPI bindings for the smsc911x driver. Convert the DT specific calls
to nonspecific device* calls, This allows the driver to work
with both ACPI and DT configurations. Ethernet should now work when using
ACPI on ARM Juno.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8d7d9cca43.
Now that the necessary infrastructure is really all there
in the tree, we can put this change back in.
Signed-off-by: David S. Miller <davem@davemloft.net>
When smsc911x uses GPIO as the interrupt controller, and if both are
loaded as modules, we get following error:
"smsc911x: Could not allocate irq resource"
This issue is because of smsc911x using platform_get_resource to get
device tree based irq resource.
commit "9ec36ca (of/irq: do irq resolution in platform_get_irq)" and
commit "7085a7 (drivers: platform: parse IRQ flags from resources)" add
support in platform_get_irq to resolve irq and irq_flags respectively
for both modern device tree and legacy static platform data platforms.
Modify smsc911x driver to use platform_get_irq to pick up irq resource
correctly and use irq_get_trigger_type to get the IRQ trigger flags.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cb6e0b3690 ("net: smc91x: make use of 4th parameter to devm_gpiod_get_index")
caused the following build warning:
drivers/net/ethernet/smsc/smc91x.c:2208:6: warning: unused variable 'res' [-Wunused-variable]
Remove the unused 'res' variable.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify accordingly.
Moreover use devm_gpiod_get_index_optional for still simpler handling.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
I recently did a rework of the smc91x driver and did some build-testing
by compiling hundreds of randconfig kernels. Unfortunately, my script
was wrong and did not actually test the configurations that mattered,
so I introduced stupid typos in almost every file I touched.
I fixed my script now, built all configurations that actually matter
and fixed all the typos, this is the result.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70661c708 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.
Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.
I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.
In particular, these combinations were previously selectable
in Kconfig but in fact broken:
- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
e.g. versatile.
None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.
There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.
arch/arm/mach-msm/board-halibut.c | 8 ++++-
arch/arm/mach-msm/board-qsd8x50.c | 8 ++++-
arch/arm/mach-pxa/idp.c | 5 +++
arch/arm/mach-pxa/lpd270.c | 8 ++++-
arch/arm/mach-realview/core.c | 7 ++++
arch/arm/mach-realview/realview_eb.c | 2 +-
arch/arm/mach-sa1100/neponset.c | 6 ++++
arch/arm/mach-sa1100/pleb.c | 7 ++++
drivers/net/ethernet/smsc/smc91x.c | 9 +++--
drivers/net/ethernet/smsc/smc91x.h | 114 ++----------------------------------------------------------
10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver tries to support multiple platforms at compile
time, but they are mutually exclusive at runtime, and not clearly
defined.
Trying to build for CONFIG_SA1100_ASSABET without CONFIG_ASSABET_NEPONSET
results in this link error:
drivers/built-in.o: In function `smc_drv_probe':
:(.text+0x33310c): undefined reference to `neponset_ncr_frob'
since the neponset_ncr_set function is not defined otherwise.
Similarly, building for both CONFIG_SA1100_ASSABET and CONFIG_SA1100_PLEB
results in a different build error:
smsc/smc91x.c: In function 'smc_drv_probe':
smsc/smc91x.c:2299:2: error: implicit declaration of function 'neponset_ncr_set' [-Werror=implicit-function-declaration]
neponset_ncr_set(NCR_ENET_OSC_EN);
^
smsc/smc91x.c:2299:19: error: 'NCR_ENET_OSC_EN' undeclared (first use in this function)
neponset_ncr_set(NCR_ENET_OSC_EN);
^
This is an attempt to fix the call site responsible for both
errors, making sure we call the function exactly when the driver
is actually trying to run on the assabet/neponset machine. With
this patch, I no longer see randconfig build errors in this file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Atari specific code to the smc91x Ethernet driver. This code is used
on the EtherNAT adapter card for the Atari Falcon extension port.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Tested-by: Christian Steigies <cts@debian.org>
[geert: Sort Kconfig entries, split in hard and soft dependencies]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If GPIOLIB=n the following build errors occur:
drivers/net/ethernet/smsc/smc91x.c: In function 'try_toggle_control_gpio':
drivers/net/ethernet/smsc/smc91x.c:2204:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2204:7: warning: assignment makes pointer from integer without a cast [enabled by default]
drivers/net/ethernet/smsc/smc91x.c:2213:2: error: implicit declaration of function 'gpiod_direction_output' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2216:3: error: implicit declaration of function 'devm_gpiod_put' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2222:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
Fix this by letting the driver depend on GPIOLIB if OF is selected.
Fixes: 7d2911c438 ("net: smc91x: Fix gpios for device tree based booting")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This chip is present on the Nios2 Development Kit 2C35.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add minimal runtime PM support (enable on probe, disable on remove), to
ensure proper operation with a parent device that uses runtime PM.
This is needed on systems where the external bus controller module of
the SoC is contained in a PM domain and/or has a gateable functional
clock. In such cases, before accessing any device connected to the
external bus, the PM domain must be powered up, and/or the functional
clock must be enabled, which is typically handled through runtime PM by
the bus controller driver.
An example of this is the kzm9g development board, where an smsc9220
Ethernet controller is connected to the Bus State Controller (BSC) of a
Renesas sh73a0 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).
I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).
It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King