88PM800 and 88PM805 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according
to requirement.
88pm80x.c provides common i2c driver handling for both 800 and
805, such as i2c_driver init, regmap init, read/write api etc.
88pm800.c handles specifically for 800, such as chip init, irq
init/handle, mfd device register, including rtc, onkey, regulator(
to be add later) etc. besides that, 800 has three i2c device, one
regular i2c client, two other i2c dummy for gpadc and power purpose.
88pm805.c handles specifically for 805, such as chip init, irq
init/handle, mfd device register, including codec, headset/mic detect
etc.
the i2c operation of both 800 and 805 are via regmap, and 88pm80x-i2c
exported a group of r/w bulk r/w and bits set API for facility.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The core and irq Arizona parts should be boolean as they depend on non
exported symbols.
This fixes the following build errors:
ERROR: "wm5102_aod" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "wm5102_irq" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "irq_set_chip_and_handler_name" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "wm5102_patch" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_init" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_exit" [drivers/mfd/arizona-core.ko] undefined!
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ARRAY_SIZE() may be larger than the number of supplies actually used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
References to the WM5102 tables need to be guarded.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We're testing for a specific value and while SPI does not detect I/O
errors I2C can.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensures we don't leak the enable we just did.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These registers will be used in future devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This ensures that if we are using a GPIO as a wake source it continues to
function while we're suspended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now we have regcache sync region we can use it to do a more efficient
sync of the pin configuration after we reset the device during suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than open coding the enable GPIO control in the MFD core use the
API to push the management on to the regulator driver. The immediate
advantage is slight for most systems but this will in future allow device
configurations where an external regulator is used for DCVDD.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While the core isn't useful by itself it does depend on regmap so try to
force that on.
Reported-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Wolfson Arizona platform is used to provide common register
interface to a series of low power audio hub CODECs, starting with the
WM5102. Since the features of these devices work over a range of
subsystems an MFD core driver is provided to instantiate the subdevices
and arbitrate access between them.
As the new regmap wake IRQ functionality is used as part of the driver
it is incorporated as a dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8pCq
-----END PGP SIGNATURE-----
Merge tag 'mfd/wm5102' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into for-next
mfd: Initial support for Wolfson Arizona platform and WM5102 devices
The Wolfson Arizona platform is used to provide common register
interface to a series of low power audio hub CODECs, starting with the
WM5102. Since the features of these devices work over a range of
subsystems an MFD core driver is provided to instantiate the subdevices
and arbitrate access between them.
As the new regmap wake IRQ functionality is used as part of the driver
it is incorporated as a dependency.
As the AB8500 is a subordinate MFD device to the DB8500-PRCMU,
for consistency and a better 1:1 depiction of how the hardware
is laid out, it is a good idea to register it in the same way
as we do for the other MFD child devices. In order for us to do
this successfully we have to pass AB8500's platform data when
registering the DB8500-PRCMU from platform code.
Also solves this issue:
WARNING: at fs/sysfs/dir.c:526 sysfs_add_one+0x88/0xb0()
sysfs: cannot create duplicate filename '/bus/platform/devices/ab8500-core.0'
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now this driver is using regmap API, the iolock mutex is not used and
can be removed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pre-regulator of 88pm8606 is mainly for support charging based on vbus,
it needs to be enabled for charging battery, and will be disabled in
some exception condition like over-temp.
Add the pre-regulator device init data and resource for mfd subdev.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add flag to platform data to enable external 32-kHz crystal oscillator
(or square wave) input.
The tps6591x can use either an internal 32-kHz RC oscillator or an
external crystal (or square wave) to generate the 32-kHz clock.
The default setting depends on the selected boot mode. In boot mode 00
the internal RC oscillator is used at power-on, but the external crystal
oscillator (or square wave) can be enabled by clearing the ck32k_ctrl
flag in the device control register.
Note that there is no way to switch from the external crystal oscillator
to the internal RC oscillator.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During conversion to regmap_irq this hunk was missing being moved
to MFD driver to put the chip into clear on read mode. Also as slave
is now set use it to determine which slave for the register call.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to a merge error the section of code passing the pdata for the
regulator driver to the mfd_add_devices via the children structure
was missing. This corrects this problem.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch add support irq domain for Maxim MAX8997 muic
instead of irq_base in platform data and max8997 driver
private data are instead. It is tested on TRATS board.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add irq domain support for max8997 interrupts. The reverse mapping method
used is linear mapping since the sub-drivers of max8997 such as regulator
and charger drivers can use the max8997 irq_domain to get the linux irq
number for max8997 interrupts. All uses of irq_base in platform data and
max8997 driver private data are removed.
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Applying a succinct description to the of_compatible variable recently
added to the mfd_cell struct. Also link to the documentation page where
more information can be found about compatible properties.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Guard PM methods with CONFIG_PM_SLEEP and get rid of some unneeded #ifdefs.
This fixes below build warnings:
CC drivers/mfd/tc3589x.o
drivers/mfd/tc3589x.c:361:12: warning: 'tc3589x_suspend' defined but not used [-Wunused-function]
drivers/mfd/tc3589x.c:375:12: warning: 'tc3589x_resume' defined but not used [-Wunused-function]
SIMPLE_DEV_PM_OPS already defines constant dev_pm_ops, thus also fix
'duplicate const' sparse warning.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes below build warnings:
CC drivers/mfd/adp5520.o
drivers/mfd/adp5520.c:324:12: warning: 'adp5520_suspend' defined but not used [-Wunused-function]
drivers/mfd/adp5520.c:333:12: warning: 'adp5520_resume' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes conflict between commit 8ae3559
"mfd: mc13xxx workaround SPI hardware bug on i.Mx"
and commit 10c7a5d "mfd: Use devm_* APIs for mc13xxx".
commit 8ae3559 changes regmap_init_spi to regmap_init.
So now we need to use devm_regmap_init rather than devm_regmap_init_spi.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.
This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.
This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.
I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.
v3 - Brown paper bag its too early in the morning actually run
git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: Mantesh Sarashetti <mantesh@ti.com>
Tested-by: Mantesh Sarashetti <mantesh@ti.com>
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allocate memory and irq for device state using devm_*
helpers to simplify memory accounting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that we leave the device with the pins in the expected
configuration if we leave it in reset over suspend, avoiding any
interoperation problems with other devices in the system.
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6040 needs CONFIG_IRQ_DOMAIN to compile, without this we have:
drivers/mfd/twl6040-irq.c: In function 'twl6040_irq_init':
drivers/mfd/twl6040-irq.c:164:2: error: implicit declaration of function 'irq_domain_add_legacy'
drivers/mfd/twl6040-irq.c:165:11: error: 'irq_domain_simple_ops' undeclared (first use in this function)
drivers/mfd/twl6040-irq.c:165:11: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to call max77693_irq_exit() in max77693_i2c_probe error patch and
max77693_i2c_remove.
Current code already uses devm_kzalloc() to allocate memory for max77693.
Thus we should not call kfree(max77693), otherwise we got double free.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 72fb92200d ("mfd/ab5500: delete
AB5500 support") deleted all files that used ab5500-core.h. That file
apparently was simply overlooked. Delete it too.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
They're not referenced outside this file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes the following sparse warnings:
drivers/mfd/max8997.c:209:4: warning: symbol 'max8997_dumpaddr_pmic' was not declared. Should it be static?
drivers/mfd/max8997.c:334:4: warning: symbol 'max8997_dumpaddr_muic' was not declared. Should it be static?
drivers/mfd/max8997.c:344:4: warning: symbol 'max8997_dumpaddr_haptic' was not declared. Should it be static?
drivers/mfd/max8997.c:426:25: warning: symbol 'max8997_pm' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of just printing the register value, also output some
description of the value.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Force the Modem wakeup by asserting the CaWakeReq signal before the
hostaccess_req/ack ping-pong sequence. The Awake_req signal is de-asserted
asserted at the same time than the hostaccess_req. Return error on failure
case so that the client using this can take appropiate steps.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since none of the users now reference the cache directly we can happily
remove the custom cache code and rely on the regmap cache.
For simplicity we don't bother with the register defaults tables but
instead read the defaults from the device - regmap is capable of doing
this, unlike our old cache infrastructure. This saves a lot of code and
allows us to cache the device revision information too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can just use regmap_update_bits() to achieve the same effect - it will
do the read/modify/update cycle for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the most simple possible transformation on the existing code so keep
the table sitting around, further patches in this series will delete the
existing cache code - the main purpose of this patch is to ensure that
we always have a cache for bisection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Hierarchically, the AB8500 is a child of the DB8500 PRCMU. So now that
Device Tree is being used and MFD core code is Device Tree aware, we
can simply register DB8500 PRCMU from Device Tree in the normal way
then allow the DB8500 PRCMU driver to register the AB8500 as a simple
MFD device at probe time.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AB8500 is soon to have its own IRQ domain. For this to be useful
the driver needs to be initialised earlier in the boot sequence. Here
we move initialisation forward from arch_initcall to core_initcall time.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now the AB8500 has its own IRQ domain it needs to be initialised earlier
in the boot sequence. As the AB8500 relies on the DB8500 PRCMU we need to
reflect this change for the PRCMU driver too.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During Device Tree enablement of the ab8500 and db8500-prcmu drivers,
a decision was made to omit registration through the MFD API and use
Device Tree directly. However, because MFD devices have a different
address space and the ab8500 and db8500 both use I2C to communicate,
this causes issues with address translation during execution of
of_platform_populate(). So the solution is to make the MFD core aware
of Device Tree and have it assign the correct node pointers instead.
To make this work the MFD core also needs to be awere of IRQ domains,
as Device Tree insists on IRQ domain compatibility. So, instead of
providing an irq-base via platform code, in the DT case we simply
look up the IRQ domain and map to the correct virtual IRQ.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is only one method used to communicate with the DB8500 PRCMU, via I2C.
Now this can be assumed, there is no requirement to specify the protocol in
the function name. This patch removes protocol specifics and uses a more
generic naming convention.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As the AB8500 is an IRQ controller in its own right, here we provide
the AB8500 driver with IRQ domain support. This is required if we wish
to reference any of its IRQs from a platform's Device Tree.
Cc: Naga Radheshy <naga.radheshy@stericsson.com>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the correct compatible string for use during Device Tree
population. Without it the DB8500 PRCMU will not be probed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Qiao Zhou