This patch renames pll_clk to sclk_clk. The clock referenced by pll_clk
is actually not the pll input clock for dsi. The pll input clock comes
from the board's oscillator directly. But for the backward
compatibility, the old clock name "pll_clk" is also OK.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
MIC(Mobile image compressor) is newly added IP in Exynos5433. MIC
resides between decon and mipi dsim, and compresses frame data by 50%.
With dsi, not display port, to send frame data to the panel, the
bandwidth is not enough. That is why this compressor is introduced.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON(Display and Enhancement Controller) is new IP replacing FIMD in
Exynos5433. This patch adds Exynos5433 decon driver.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
These bindings support the GPIO controllers found on the Qualcomm
Atheros AR7xxx/AR9XXX SoC.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The DDR controller of the ARxxx and AR9xxx families provides an
interface to flush the FIFO between various devices and the DDR.
This is mainly used by the IRQ controller to flush the FIFO before
running the interrupt handler of such devices.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a binding document for the USB2.0 PHY found on the IMG Pistachio SoC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=I0gO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
Add DT bindings documentation for the new marvell-cesa driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We are about to add a new driver to support new features like using the
TDMA engine to offload the CPU.
Orion, Dove and Kirkwood platforms are already using the mv_cesa driver,
but Orion SoCs do not embed the TDMA engine, which means we will have to
differentiate them if we want to get TDMA support on Dove and Kirkwood.
In the other hand, the migration from the old driver to the new one is not
something all people are willing to do without first auditing the new
driver.
Hence we have to support the new compatible in the mv_cesa driver so that
new platforms with updated DTs can still attach their crypto engine device
to this driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The mv_cesa driver currently expects the SRAM memory region to be passed
as a platform device resource.
This approach implies two drawbacks:
- the DT representation is wrong
- the only one that can access the SRAM is the crypto engine
The last point is particularly annoying in some cases: for example on
armada 370, a small region of the crypto SRAM is used to implement the
cpuidle, which means you would not be able to enable both cpuidle and the
CESA driver.
To address that problem, we explicitly define the SRAM device in the DT
and then reference the sram node from the crypto engine node.
Also note that the old way of retrieving the SRAM memory region is still
supported, or in other words, backward compatibility is preserved.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On Dove platforms, the crypto engine requires a clock. Document this
clocks property in the mv_cesa bindings doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge the mvebu/drivers branch of the arm-soc tree which contains
just a single patch bfa1ce5f38 ("bus:
mvebu-mbus: add mv_mbus_dram_info_nooverlap()") that happens to be
a prerequisite of the new marvell/cesa crypto driver.
Earlycon calculates UART clock as "BASE_BAUD * 16". In case of ARC
"BASE_BAUD" is calculated dynamically in runtime, basically it is an
alias to arc_early_base_baud(), which in turn just does
"arc_base_baud/16".
8250 UART on AXS/SDP board uses 33.3MHz clock source which is set in
"arc_base_baud" with this change.
Additional compatibility string "snps,arc-sdp" is introduced as well
because there're different flavours of AXS boards but they all share the
same motherboard and so it's possible to re-use the same code for
motherbord even if CPU daughterboard changes.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The AXS10x platforms consist of a mainboard with peripherals,
on which several daughter cards can be placed. The daughter cards
typically contain a CPU and memory.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add DT binding documentation for lpc1850-cgu driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Main PLL controller has post divider bits in a separate register in
pll controller. Use the value from this register instead of fixed
divider when available.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
One error fix, and one patch to add support for the USB clock found on the
Allwinner A23 and A33
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uxrz
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner clocks additions for 4.2
One error fix, and one patch to add support for the USB clock found on the
Allwinner A23 and A33
Remove old Cygnus dummy clock binding document, as it's replaced by
Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Document the device tree binding for Broadcom iProc architecture based
clock controller
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Add sama5d2 support to irq-atmel-aic5.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: http://lkml.kernel.org/r/1434632855-27272-1-git-send-email-nicolas.ferre@atmel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This contains fixes for the long-standing build issues that some of the
bridge drivers were exposing. Other than that it's mostly cleanup and a
couple of new simple panels that are supported.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4rJg
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.2-rc1
This contains fixes for the long-standing build issues that some of the
bridge drivers were exposing. Other than that it's mostly cleanup and a
couple of new simple panels that are supported.
* tag 'drm/panel/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: simple: Add bus format for HannStar HSD100PXN1
drm/panel: simple: Add display timing for HannStar HSD100PXN1
drm/panel: ld9040: Remove useless padding
drm/panel: Constify OF match tables
drm/bridge: Remove stale ptn3460.h include
drm/bridge: ps8622: Include linux/gpio/consumer.h
drm/bridge: ptn3460: Include linux/gpio/consumer.h
drm/bridge: dw-hdmi: Return number of EDID modes
drm/panel: simple: Add support for LG LB070WV8 800x480 7" panel
drm/bridge: ptn3460: Pass flags to devm_gpiod_get()
drm/bridge: ps8622: Pass flags to devm_gpiod_get()
drm/bridge: ptn3460: Fix I2C ID table to match the reported modalias
drm/bridge: dw-hdmi: Staticize dw_hdmi_bridge_funcs
The rk3368 is the first ARM64 soc from Rockchip, but seems to share most
peripherals with the ARM32 soc, including the pinctrl functionality.
The only notable difference is - as with every Rockchip soc - that the
offsets in the General Register Files moved around and a split of the pmu
section of the rk3288 into pmu and pmugrf (pmu general register files)
sections. The pinctrl driver of course only needs the pmugrf registers
for controlling the pin settings.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the device tree bindings document for the TI Wakeup M3 remote
processor devices on AM33xx and AM43xx SoCs. These devices are used
to offload low-level power management functionality, and are handled
by the wkup_m3 remoteproc driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
- add new property "atmel,fifo-size"
- change "cs-gpios" to optional for SPI controller version >= 2.
Please be aware that the VERSION register can not be used to guess the
size of FIFOs. Indeed, for a given hardware version, the SPI controller
can be integrated on Atmel SoCs with different FIFO sizes. Also the
"atmel,fifo-size" property is optional as older SPI controllers don't
embed FIFO at all.
Besides, the FIFO size can not be read or guessed from other registers:
When designing the FIFO feature, no dedicated registers were added to
store this size. Unused spaces in the I/O register range are limited and
better reserved for future usages. Instead, the FIFO size of each
peripheral is documented in the programmer datasheet.
Finally, on a given SoC, there can be several instances of the SPI
controller with different FIFO sizes. This explain why we'd rather use a
dedicated DT property than use the "compatible" property.
For instance, sama5d2x SoCs come with some SPI controllers, the ones
inside Flexcoms, integrating 32 data FIFOs whereas other SPI controllers
use 16 data FIFOs. All these SPI controllers share the same IP version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the DPCM based machine driver with rt5650 and rt5676
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the DPCM based platform driver of AFE (Audio Front End) unit.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
PM8916 PMICs. This driver is based largely on code from
codeaurora.org[1].
[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/qpnp-regulator.c?h=msm-3.10
Cc: David Collins <collinsd@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PFC support for the R8A7794 SoC including pin groups for some
on-chip devices such as ETH, I2C, INTC, MSIOF, QSPI, [H]SCIF...
Sergei: squashed together several patches, fixed the MLB_CLK typo,
added IRQ4.. IRQ9 pin groups, fixed IRQn comments, added ETH B pin
group names, removed stray new line and fixed typos in the comments
in the pinmux_config_regs[] initializer, removed the platform device
ID, took into account limited number of signals in the GPIO1/5/6
controllers, added reasonable and removed unreasonable
copyrights, modified the bindings document, renamed, added changelog.
Changes in version 5:
- resolved rejects, refreshed the patch;
- added Laurent Pinchart's ACK.
Changes in version 4:
- reused the PORT_GP_26() macro to #define PORT_GP_28().
Changes in version 3:
- removed the platform device ID;
- added PORT_GP_26() and PORT_GP_28() macros, used them for GPIO1/5/6 in the
CPU_ALL_PORT() macro.
Changes in version 2:
- rebased the patch.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the NFC pull request for 4.2.
- NCI drivers can now define their own handlers for processing
proprietary NCI responses and notifications.
- NFC vendors can use a dedicated netlink API to send their own
proprietary commands, like e.g. all commands needed to implement
vendor specific manufacturing tools.
- A new generic NCI over UART driver against which any NCI chipset
running on top of a serial interface can register.
- The st21nfcb driver is renamed to st-nci as it can and will support
most of ST Microelectronics NCI chipsets.
- The st21nfcb driver can put its CLF in hibernate mode and save
significant amount of power.
- A few st21nfcb minor fixes.
- The NXP NCI driver now supports ACPI enumeration.
- The Marvell NCI driver now supports both USB and serial
physical interfaces.
- The Marvell NCI drivers also supports NCI frames being muxed
over HCI. This is a setting that can be defined by a DT property.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+IG2
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.2 pull request
This is the NFC pull request for 4.2.
- NCI drivers can now define their own handlers for processing
proprietary NCI responses and notifications.
- NFC vendors can use a dedicated netlink API to send their own
proprietary commands, like e.g. all commands needed to implement
vendor specific manufacturing tools.
- A new generic NCI over UART driver against which any NCI chipset
running on top of a serial interface can register.
- The st21nfcb driver is renamed to st-nci as it can and will support
most of ST Microelectronics NCI chipsets.
- The st21nfcb driver can put its CLF in hibernate mode and save
significant amount of power.
- A few st21nfcb minor fixes.
- The NXP NCI driver now supports ACPI enumeration.
- The Marvell NCI driver now supports both USB and serial
physical interfaces.
- The Marvell NCI drivers also supports NCI frames being muxed
over HCI. This is a setting that can be defined by a DT property.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DSPI driver has been updated and support more compatible strings.
This patch update the DT binding documentation.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some ECs need a little time for waking up before they can accept
SPI data at a high speed. Add a "google,cros-ec-spi-pre-delay"
property to the DT binding to configure this.
If this property isn't set, then no delay will be added. However,
if set it will cause a delay equal to the value passed to it to
be inserted at the beginning of a transaction.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is binding information for the UniPhier on-chip UART driver
(drivers/tty/serial/8250/8250_uniphier.c).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add bindings documentation for GQSPI controller driver used by
Zynq Ultrascale+ MPSoC
Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the Hannstar HSD100PXN1 to the DRM simple panel driver.
The HSD100PXN1 is an XGA (1024x768) panel with an 18-bit LVDS interface.
It supports pixel clocks in the range of 55-75 MHz.
This panel is offered for sale by Freescale as a companion part to its'
i.MX5x Quick Start board and i.MX6 SABRE platforms with under the name
MCIMX-LVDS1.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mclk-fs ratio property per dai-link sub node. This will
allow to manage several codecs with different ratio.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Hardware Spinlock device on atlas7 provides hardware assistance
for synchronization between the multiple processors in the system
(dual Cortex-A7, CAN bus Cortex-M3 and audio DSP).
This patch adds the DT bindings information for this hwspinlock
module.
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Wei Chen <wei.chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
* zte/soc:
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
Add initial dts file and document for ZX296702 and board ZX296702-AD1.
More peripherals will be added later.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LybA
-----END PGP SIGNATURE-----
Merge tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Samsung updates for v4.2
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
* tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (301 commits)
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
ARM: EXYNOS: Get current parent clock for power domain on/off
ARM: SAMSUNG: fix clk_enable() WARNing in S3C24XX ADC
ARM: EXYNOS: Add missing of_node_put() when parsing power domains
ARM: EXYNOS: Handle of_find_device_by_node() and kstrdup() failures
ARM: EXYNOS: Handle of of_iomap() failure
Linux 4.1-rc4
....
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZQaR
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung another DT udpates for v4.2
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
* tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (33 commits)
ARM: dts: add sysmmu nodes for exynos5420
ARM: dts: add sysmmu nodes for exynos5250
ARM: dts: add sysmmu nodes for exynos4415
ARM: dts: add sysmmu nodes for exynos3250
ARM: dts: add sysmmu nodes for exynos4
ARM: dts: Add Odroid XU3 Lite support
of: Add vendor prefix for Hardkernel
ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC
ARM: dts: exynos5420: add nodes for jpeg codec
ARM: dts: s3c2416: Use labels for overriding nodes in SMDK2416
ARM: dts: s3c2416: Add labels to S3C2416 nodes
ARM: dts: Use labels for overriding nodes in exynos5422-odroidxu3
ARM: dts: Use labels for overriding nodes in exynos5440 boards
ARM: dts: Use labels for overriding nodes in exynos5420-smdk5420
ARM: dts: Use labels for overriding nodes in exynos542x
ARM: dts: Use labels for overriding nodes in exynos5420-arndale-octa
ARM: dts: Remove duplicated I2C7 nodes in exynos5250-snow
ARM: dts: Use labels for overriding nodes in exynos5250
ARM: dts: Add labels to exynos5 nodes
ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into next/dt
Linux 4.1-rc6
Conflicts:
arch/arm/boot/dts/zynq-7000.dtsi
Resolution summary:
Mainline had an earlier version of the commit, resolve in favor of the
newer patch in next/dt branch.
- for exyos3250
: use s3c6410-rtc instead of exynos3250-rtc
: add JPEG codec node and support it on exynos3250-rinato
: use s3c-rtc clock id for exynos3250-rinato and monk boards
- for exynos4
: add JPEG codec node and syscon property to MIPI DPHY
: remove obsolete MIPI DPHY reg property
: enable s3c-rtc on exynos4412-trats2
- for exynos5
: add syscon property to MIPI DPHY for exynos5420
: enable s3c-rtc on exynos5420-arndale-octa
: add missing irq pinctrl for max77686 on exynos5250-smdk5250
: clk: add bindings for 32kHz clocks from s2mps11
: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
- for exynos5422-odroidxu3
: add mmc detect gpio and LEDs
: add HS400 support, simple-audio-card and rtc_src clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bWPy
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung DT updates for v4.2
- for exyos3250
: use s3c6410-rtc instead of exynos3250-rtc
: add JPEG codec node and support it on exynos3250-rinato
: use s3c-rtc clock id for exynos3250-rinato and monk boards
- for exynos4
: add JPEG codec node and syscon property to MIPI DPHY
: remove obsolete MIPI DPHY reg property
: enable s3c-rtc on exynos4412-trats2
- for exynos5
: add syscon property to MIPI DPHY for exynos5420
: enable s3c-rtc on exynos5420-arndale-octa
: add missing irq pinctrl for max77686 on exynos5250-smdk5250
: clk: add bindings for 32kHz clocks from s2mps11
: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
- for exynos5422-odroidxu3
: add mmc detect gpio and LEDs
: add HS400 support, simple-audio-card and rtc_src clock
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add syscon property to the MIPI DPHY for exynos4415
ARM: dts: Remove obsolete MIPI DPHY 'reg' property for exynos4
ARM: dts: Use last parent for clocks during power domain on/off
ARM: dts: add support JPEG codec for exynos3250-rinato
ARM: dts: support simple-audio-card for exynos5420 and exynos5422-odroidxu3
ARM: dts: add jpeg-codec node for exynos4 and exynos4x12
ARM: dts: Enable S3C RTC on exynos4412-trats2 and exynos5420-arndale-octa
ARM: dts: Use define for s3c-rtc clock id for exynos3250-monk
ARM: dts: Use define for s3c-rtc clock id for exynos3250-rinato
ARM: dts: Use s3c6410-rtc instead of exynos3250-rtc for exynos3250/4415
ARM: dts: add 'rtc_src' clock to rtc node for exynos5422-odroidxu3
clk: samsung: Add bindings for 32kHz clocks from s2mps11
ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
ARM: dts: Add syscon property to the MIPI phy in exynos5420
ARM: dts: Add HS400 support for exynos5422-odroidxu3
ARM: dts: Add LEDs for exynos5422-odroidxu3
ARM: dts: add mmc detect gpio for exynos5422-odroidxu3
ARM: dts: add JPEG codec device node for exynos3250
ARM: dts: Add missing irq pinctrl for max77686 on smdk5250
Some targets (eg: msm8994) use the pinctrl framework to configure
interface pins. This change adds support for initialization and
pinctrl active/sleep state control for the HDMI driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are different types of PHY from one chipset to another, while
the DSI host controller is relatively consistent across platforms.
Also, the PLL inside PHY is providing the source of DSI byte and
pixel clocks, which are used by DSI host controller. Separated devices
for clock provider and clock consumer make DSI driver better fit into
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A new API call has been introduced which allows channels to be
requested by name. This new call uses the 'mbox-names' property,
so users need no further discouragement from supplying it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Ethernet AVB includes an Gigabit Ethernet controller (E-MAC) that is basically
compatible with SuperH Gigabit Ethernet E-MAC. Ethernet AVB has a dedicated
direct memory access controller (AVB-DMAC) that is a new design compared to the
SuperH E-DMAC. The AVB-DMAC is compliant with 3 standards formulated for IEEE
802.1BA: IEEE 802.1AS timing and synchronization protocol, IEEE 802.1Qav real-
time transfer, and the IEEE 802.1Qat stream reservation protocol.
The driver only supports device tree probing, so the binding document is
included in this patch.
Based on the original patches by Mitsuhiro Kimura.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sNVc
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third round of new IIO drivers, cleanups and functionality for the 4.2 cycle.
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVb7iWAAoJEFBXWFqHsHzOIGEIAJjoZ+80PKH6+obh7gCuEkIx
MkZobKxYyRRh+wD+7NZEqSPMYxBW6eUCYGCCy+f/4xjmlIfHkp/DaaCeIU0EZItl
GU1ZE7qg6kWGbamun7zXcrg1cZ+bFOpQ926isETurL8LC2+PLm6OSg1pl6hwjqpA
rGzY2aEH5Lke6wDN0cMus0ApMlIQ8HpOLABtqosuzUWclyZBmoxBQshbW8ztzS3Y
pjpRfAHS91+0vZpoqmULTc/ENbTToNYk5NxJgMMDigkz1Gqp0Ni+rxmDmRPayo09
/Nq4VHDT+wx3CSf6nC9YIrabxrBMpvTky2jWOAJ4OxMFjT0xle3XISGRoa1ifqo=
=PbGi
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.2:
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
* tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
ARM: dts: imx6dl: add imx6dl gpt specific compatible string
ARM: dts: imx6: add DT for aristainetos2 board
ARM: dts: cubox-i/hummingboard: Fix the license text
ARM: dts: sabrelite: use simple-panel instead of display-timings for LVDS0
ARM: dts: nitrogen6x: use simple-panel instead of display-timings for LVDS0
ARM: dts: add imx7d-sdb support
ARM: dts: add imx7d soc dtsi file
ARM: dts: Armadeus Systems APF6 family support (i.MX6)
ARM: dts: vf610: Nomenclature fixup for PTC12 pin used in RMII mode.
ARM: dts: cubox-i: add support for Broadcom Wifi/Bluetooth devices
Document: dt: binding: imx: update document for imx7d support
ARM: dts: imx6qdl: Add power-domain phandle to CODA device node
ARM: dts: Gateworks GW5510 support (i.MX6)
ARM: dts: imx6sl-warp: Fix OTG roles
ARM: dts: imx6sl-warp: Remove USB regulators
ARM: dts: imx6sl-warp: Remove unused regulator
ARM: dts: add pinfunc include file to support imx7d
ARM: mxs: fix in tree users of ssd1306
ARM: dts: imx6qdl-hummingboard: Add PCIe support
ARM: dts: imx23-olinuxino: Add i2c support
...
These options make it possible to overwrites the data and instruction
prefetching behavior of the arm pl310 cache controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-rt5645
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
Modify the RT5645 driver to parse platform data from device tree.
Write a DT binding document to describe those properties.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds bindings for apq8016 sbc machine driver.
APQ8016 has 4 MI2S which can be configured to different sinks like
internal codec/external codec, this connection and various parameters
are controlled via 2 iomux registers.
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Marvell Armada 38x SoC introduce new features to the XOR engine,
especially the fact that the engine mode (MEMCPY/XOR/PQ/etc) can be part of
the descriptor and not set through the controller registers.
This new feature allows mixing of different commands (even PQ) on the same
channel/chain without the need to stop the engine to reconfigure the engine
mode.
Refactor the driver to be able to use that new feature on the Armada 38x,
while keeping the old behaviour on the older SoCs.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_*
properties support") added support for setting voltage and temperature
thresholds with platform data. For DeviceTree default of 0 was always
used.
This caused reporting battery health always as over voltage or
over heated.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_* properties support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
add a new value "atmel,sama5d2-i2c" for the "compatible" property.
add a new optional property "atmel,fifo-size" to enable FIFO support when
available.
add missing optional properties "dmas" and "dma-names".
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Armada 39x SoC family has grown a new variant, the Armada 395,
which sits between the Armada 390 and Armada 398 in terms of
features. This commit adds support for this additional variant to the
Armada 39x pinctrl driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 39x datasheet documents several new
SATA related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 39x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 39x datasheet documents several new
PCIe related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 39x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
PTP related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
UART1 related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
NAND related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
SATA related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest Armada XP datasheet documents several new DRAM related
functions on various MPPs. This commit adds the description of these
new functions in the Armada XP pinctrl driver and its DT binding
documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada XP datasheet documents a new
NAND-related MPP function on MPP48, for which this commit adds
support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest Armada XP datasheet documents that some of the MPP pins can
be used to access the second SPI bus, labelled 'spi1'. This commit
adds the corresponding pins in the pinctrl driver and its DT binding
documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to the latest Armada XP datasheet, we discovered that
there is a second SPI bus accessible from the MPP pins, called 'spi1'.
In order to be consistent with other SoCs having two SPI busses, this
commit renames the functions of the first SPI bus to 'spi0' instead of
just 'spi'.
This commit obviously breaks the DT backward compatibility for the
people using the "spi" function name in their Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Across all SoCs, even on Armada 370 for SPI0, the clock pin uses the
'sck' subname and not 'clk', so this commit adjusts the code and
documentation accordingly.
Since this commit only changes the subname, DT backward compatibility
is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For consistency with the datasheet, this commit renames the VDD
function of the MPP4 pin.
While this changes the DT compatibility, it is not considered to be a
problem since this pin is unlikely to be used for anything but
debugging purposes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was an off-by-one in the documentation of the ge1(txd[0-3])
pins, which is fixed by this commit. Since the driver was correct, and
the subnames are anyway not used in the DT binding itself, there is no
need to push this documentation fix for stable.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of the Ethernet txclkout pin to be
the same accross Marvell SoCs. It is worth mentioning that the DT
binding documentation of the Armada XP was wrong for MPP12: it said
the function was ge1(txd0), while it is in fact ge1(txclkout). It is
however not really a fix worth sending to stable since it does not
change the behavior, and the driver itself was correct.
Since only the subnames are changed, DT backward compatibility is not
affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit aligns the naming of the audio 'lrclk' pin accross Marvell
SoCs.
Since only the subname is changed, the DT backward compatibility is
not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of PCIe pins to use 'rstout' instead
of 'rstoutn' or 'rst-out'.
Since only the subnames are changed, DT compatibility is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of the TDM pins accross the
different Marvell SoCs. Mainly it consists in:
* Removing the 'n' from signal names: 'intn' becomes 'int' and 'rstn'
becomes 'rst'
* Renaming the main name 'tdm2c' to 'tdm' on Armada 38x.
* Change the main name 'tdm-1' to 'tdm' for one of the pins of the
Armada XP
The last two changes affect DT compatibility, but since the TDM
interface is nowhere near being supported in mainline, it should not
be considered to be a serious problem at this point.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All SoCs use "nand" to designate NAND pins, only Armada 39x is using
"nd", which is not consistent. This commit fixes that by renaming the
corresponding functions.
It also changes the subnames from rbn0/rbn1 to rb0/rb1, to respect the
convention used everywhere that we don't encode the 'n' part of signal
names.
While this commit changes the main name of function, therefore
potentially breaking the DT compatibility, this is not a problem since
Armada 39x is a brand new SoC which isn't used in production yet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit modifies the definition of the Device Bus interface pins
to be consistent accross SoCs. Especially, it removes the 'n'
indicators that we don't encode in the subnames of pins:
'dev(wen0)' becomes 'dev(we0)'
'dev(wen1)' becomes 'dev(we1)'
'dev(oen)' becomes 'dev(oe)'
etc.
In addition, it fixes the Armada 375 DT binding documentation, which
forgot to document the 'dev' function for MPP46, MPP57 and MPP63.
Since only the subnames are changed, this commit does not affect DT
compatibility.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to be consistent with the datasheet and some other SoCs, this
commit renames the SDIO pins of the Armada 39x from "sd" to "sd0".
While this changes the DT binding, this is not a problem since Armada
39x is a brand new SoC which isn't used in production yet (so now is
the right time to fix such things).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit makes the naming of SATA related MPP functions consistent
accross SoCs by adjusting the Armada 39x definition to use "prsnt"
instead of "present".
Since only the subnames are changed, the DT binding is not modified at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit makes the dram functions naming (both the name and
subname) consistent accross SoC, by using:
dram(vttctrl)
dram(deccerr)
in all Marvell SoCs.
Due to the change to the name, it changes the DT binding, but these
functions are not used by any in-tree Device Tree file, and are very
unlikely to be used by anyone.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The subnames are purely informative, but it's nicer when they match
accross SoCs. This commit adjusts the Armada 375, Armada 38x and
Armada 39x MPP definitions so that the subnames of the PTP pins match
the ones used on Armada XP and Kirkwood.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was a mistake in the definition of the functions for MPP48 on
Marvell Armada XP. The second function is dev(clkout), and not tclk.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada XP datasheet no longer documents the
VDD cpu_pd functions, which might indicate they are not working and/or
not supported. This commit ensures the pinctrl driver matches the
datasheet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to a more recent version of the Armada XP datasheet, we
realized that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to a more recent version of the Armada 375, we realized
that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ce3ed59dcd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly
named "spi0-1" instead of just "spi0". This commit fixes that.
This DT binding change does not affect any of the in-tree users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 5f597bb2be ("pinctrl: mvebu: add pinctrl driver for Armada 370")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new revision of the Marvell Armada 38x hardware datasheet unveiled
that the definition of some of the PCIe functions were not
correct. This commit fixes the pinctrl driver accordingly.
Some PCIe functions simply do not exist, some of the PCIe functions in
fact were corresponding to other functions, and some PCIe functions
have been added.
Note: the seemingly unrelated removal of spi(cs2) on MPP47 is related:
this function is in fact implemented on MPP43, instead of a PCIe
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ca6d9a084b ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added support to Zynq Ultrascale+ MPSoC on the existing zynq
gpio driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Combine the ChipIdea USB binding into a single document to reduce
duplication and fragmentation. This marks use of the old PHY bindings as
deprecated. Future compatible bindings should use generic PHY binding.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxim MAX77621 device is high-efficiency, three-phase,
DC-DC step-down switching regulator delivers peak
output currents up to 16A. This device is extension of
MAX8973 and compatible with the register definition.
The MAX77621 has the SHUTDOWN pin which is EN pin on the
MAX8973. On MAX77621, the SHUTDOWN pin (active low) reset
device register to its POR/OTP value. The voltage output
is enabled when SHUTDONW pin is HIGH and EN bit on VOUT
register is HIGH.
For MAX8973, VOUT is enabled when EN bit or EN pin is high.
Add support of the MAX77621 device on max8973 regulator driver
with following changes:
- Make sure SHUTDOWN pin is set HIGH through GPIO calls if
GPIO from AP connected to SHUTDOWN pin provided.
- Enable/disable the rail through register access only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch was split out of Lubomir's original mailbox patch by Eric
Anholt, and the required properties documentation and examples have
been filled out more completely and updated for the driver being
changed to expose a single channel.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Craig McGeachie <slapdau@yahoo.com.au>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Freescale introduced QorIQ series SOCs, like ls1021 ls2085, with AHCI
sata support. It complies with the serial ATA 3.0 specification
and the AHCI 1.3 specification.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the LIS331DL sensor version. This is
a simple 8bit-only accelerometer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP: small set of misc. DT fixes; boot fix for THUMB2 kernel
- mediatek: PMIC fixes; DT fix for model name
- exynos: wakeup interupt fixes for 3250
- mvebu: revert mbus patch which broke DMA masters
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gSjy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP:
small set of misc DT fixes; boot fix for THUMB2 kernel
- mediatek:
PMIC fixes; DT fix for model name
- exynos:
wakeup interupt fixes for 3250
- mvebu:
revert mbus patch which broke DMA masters
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
arm64: dts: mt8173-evb: fix model name
ARM: exynos: Fix wake-up interrupts for Exynos3250
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
soc: mediatek: Add compile dependency to pmic-wrapper
soc: mediatek: PMIC wrap: Fix register state machine handling
soc: mediatek: PMIC wrap: Fix clock rate handling
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add overview of tas2552's clock configuration and selection.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyungwon Hwang