Currently we have no way to assign tty->port while performing tty
installation. There are two ways to provide the link tty_struct =>
tty_port. Either by calling tty_port_install from tty->ops->install or
tty_port_register_device called instead of tty_register_device when
the device is being set up after connected.
In this patch we modify most of the drivers to do the latter. When the
drivers use tty_register_device and we have tty_port already, we
switch to tty_port_register_device. So we have the tty_struct =>
tty_port link for free for those.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the /dev/ node not to be available before we call
tty_register_device. Otherwise we might race with open and
tty_struct->port might not be available at that time.
This is not an issue now, but would be a problem after "TTY: use
tty_port_register_device" is applied.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows drivers like ttyprintk to avoid hacks to create an
unnumbered node in /dev. It used to set TTY_DRIVER_DYNAMIC_DEV in
flags and call device_create on its own. That is incorrect, because
TTY_DRIVER_DYNAMIC_DEV may be set only if tty_register_device is
called explicitly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now, that we have flags and know everything needed, keep a promise
and move all the tables and ports allocation from tty_register_driver
to tty_alloc_driver.
Not only that it makes sense, but we need this for
tty_port_link_device which needs tty_driver->ports but is to be called
before tty_register_driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the new driver allocation interface, as this is one of the
special call-sites. Here, we need TTY_DRIVER_DYNAMIC_ALLOC to not
allocate tty_driver->ports, cdevs and potentially other structures
because we reserve too many lines in pty. Instead, it provides the
tty_port<->tty_struct link in tty->ops->install already.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to allow drivers that use neither tty_port_install nor
tty_port_register_device to link a tty_port to a tty somehow. To
avoid a race with open, this has to be performed before
tty_register_device. But currently tty_driver->ports is allocated even
in tty_register_device because we do not know whether this is the PTY
driver. The PTY driver is special here due to an excessive count of
lines it declares to handle. We cannot handle tty_ports there this
way.
To circumvent this, we start passing tty_driver flags to
alloc_tty_driver already and we create tty_alloc_driver for this
purpose. There we can allocate tty_driver->ports and do all the magic
between tty_alloc_driver and tty_register_device. Later we will
introduce tty_port_link_device function for that purpose.
All drivers should eventually switch to this new tty driver allocation
interface.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On module unload, in tty3270_exit, we forgot to free the tty driver.
Add there a call to put_tty_driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After tty_register_driver is called, it is too late to initialize a
guy with which we operate in open. When a process already called
open(2) on that node, the structures may be in use uninitialized.
Move the initialization prior to tty_register_driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Samo Pogacnik <samo_pogacnik@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a user provides a buffer larger than a tty->write_buf chunk and
passes '\r' at the end of the buffer, we touch an out-of-bound memory.
Add a check there to prevent this.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org (everything maintained past v2.6.37)
Cc: Samo Pogacnik <samo_pogacnik@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For many cards, this saves some IO space because interrupt status port
has precedence over the rest of ports on the card. Hence it can be
mapped to a hole in I/O ports.
Here we add a kernel parameter which allows that if a user wants to.
But they need to explicitly enable it by a module parameter.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now we have enough of tty_ports, so we can signal the TTY layer to
use them by tty_port_register_device.
The upside is that we look like we can introduce tty_port_easy_open
and put it directly as tty_operations->open to drivers doing nothing
in open and using tty_port_register_device. Because the easy open can
obtain a tty_port rather easily from a tty now. Heh, what a nice
by-product.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have *one* tty_port for both TTYs. How this was supposed to
work? Change it to have a tty_port for each of TTYs.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fail paths in ->probe and pti_init are incomplete. Fix that by adding
proper clean-up paths.
Note that we used to leak tty_driver on module unload. This is fixed
here too.
tty_unregister_driver needs not retval checking, so remove that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, probe initializes some parts. Then, some of them are
unwound in ->remove, some in module_exit. Let us do the opposite of
whole ->probe in ->remove.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is lost somewhere in the forest. Move it to have it along
with probe and other pci_driver stuff.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ioremap space is different to iomap. ->probe function uses ioremap,
but ->remove calls pci_iounmap. That one is illegal. Fix that by using
iounmap.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we set drvdata unconditionally in ->probe, we need not check if it
is NULL. Let us remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is annotated as __devinitconst. Despite the annotation is useless
in most cases, const keyword is misssing there. So we are placing
non-const data into rodata section. Fix that now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to link a port to a tty in install. And since dlci is
allocated even in open, we need to create gsmtty_install, allocate
dlci there and create also the link.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_struct->termios is no longer a pointer. This was changed recently
by "tty: move the termios object into the tty". But 68328serial was
not changed, so we now have a compilation error:
68328serial.c: In function 'change_speed':
68328serial.c:518:22: error: invalid type argument of '->' (have 'struct ktermios')
68328serial.c: In function 'rs_set_ldisc':
68328serial.c:620:31: error: invalid type argument of '->' (have 'struct ktermios')
68328serial.c: In function 'rs_set_termios':
68328serial.c:988:20: error: invalid type argument of '->' (have 'struct ktermios')
Fix that now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case alloc_tty_struct fails in pty_common_install, we pass NULL to
free_tty_struct. This is invalid as the function is not ready to cope
with that. And even if it was, it is not nice to do that anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PARMRK is set and large transfers of characters that will get
marked are being received, n_tty could drop data silently (i.e.
without reporting any error to the client). This is because
characters have the potential to take up to three bytes in the line
discipline (when they get marked with parity or framing errors), but
the amount of free space reported to tty_buffer flush_to_ldisc (via
tty->receive_room) is based on the pre-marked data size.
With this patch, the n_tty layer will no longer assume that each byte
will only take up one byte in the line discipline. Instead, it will
make an overly conservative estimate that each byte will take up
three bytes in the line discipline when PARMRK is set.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix possible panic caused by unlocked access to tty->read_cnt in
while-loop condition in n_tty_read().
Signed-off-by: Stanislav Kozina <skozina@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The termios and other changes mean the other protections needed on the driver
tty arrays should be adequate. Turn it all back on.
This contains pieces folded in from the fixes made to the original patches
| From: Geert Uytterhoeven <geert@linux-m68k.org> (fix m68k)
| From: Paul Gortmaker <paul.gortmaker@windriver.com> (fix cris)
| From: Jiri Kosina <jkosina@suze.cz> (lockdep)
| From: Eric Dumazet <eric.dumazet@gmail.com> (lockdep)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We sometimes pass NULL pointers to free_tty_struct(). One example where
it can happen is in the error handling code in pty_common_install().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're trying to save the termios state and we need to allocate a buffer
to do it. Smatch complains that the buffer is leaked at the end of the
function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the leak of a tty kref that Jiri pointed out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the termios stuff but while we are at it do something about the rest of
it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixes these errors:
drivers/usb/serial/console.c: In function 'usb_console_setup':
drivers/usb/serial/console.c:168:16: error: invalid type argument of '->' (have 'struct ktermios')
drivers/usb/serial/console.c:169:4: error: incompatible type for argument 1 of 'tty_termios_encode_baud_rate'
include/linux/tty.h:449:13: note: expected 'struct ktermios *' but argument is of type 'struct ktermios'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull OLPC platform updates from Andres Salomon:
"These move the OLPC Embedded Controller driver out of
arch/x86/platform and into drivers/platform/olpc.
OLPC machines are now ARM-based (which means lots of x86 and ARM
changes), but are typically pretty self-contained.. so it makes more
sense to go through a separate OLPC tree after getting the appropriate
review/ACKs."
* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
x86: OLPC: move s/r-related EC cmds to EC driver
Platform: OLPC: move global variables into priv struct
Platform: OLPC: move debugfs support from x86 EC driver
x86: OLPC: switch over to using new EC driver on x86
Platform: OLPC: add a suspended flag to the EC driver
Platform: OLPC: turn EC driver into a platform_driver
Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
drivers: OLPC: update various drivers to include olpc-ec.h
Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver
This branch contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the branch
into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xb8w
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree, but
didn't go in because the pull request ended up rejected. So it just got
merged, and we got this staged branch that enables the coupled cpuidle
code on OMAP.
With a stable git workflow from the other maintainer we could have staged
this earlier, but that wasn't the case so we have had to merge it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't push
back hard in that direction.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Wp41
-----END PGP SIGNATURE-----
Merge tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
"Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
but didn't go in because the pull request ended up rejected. So it
just got merged, and we got this staged branch that enables the
coupled cpuidle code on OMAP.
With a stable git workflow from the other maintainer we could have
staged this earlier, but that wasn't the case so we have had to merge
it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't
push back hard in that direction."
* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP4: CPUidle: Open broadcast clock-event device.
ARM: OMAP4: CPUidle: add synchronization for coupled idle states
ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus
A few fixes for merge window fallout, and a bugfix for timer resume
on PRIMA2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BkSN
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for merge window fallout, and a bugfix for timer resume on
PRIMA2."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mmp: add missing irqs.h
arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
ARM: mxc: Include missing irqs.h header
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlAaIN8ACgkQGkmNcg7/o7gpMgCgtmCJeUrSCc/eVKGy5ik1BPnC
3DAAoLdqCJflwx4mrN48kkXQj9SA4Xko
=Y6yl
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
sh: explicitly include sh_dma.h in setup-sh7722.c
sh: ecovec: care CN5 VBUS if USB host mode
sh: sh7724: fixup renesas_usbhs clock settings
sh: intc: initial irqdomain support.
sh: pfc: Fix up init ordering mess.
serial: sh-sci: fix compilation breakage, when DMA is enabled
dmaengine: shdma: restore partial transfer calculation
sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
sh: Fix up recursive fault in oops with unset TTB.
sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
sh: select the fixed regulator driver on several boards
sh: ecovec: switch MMC power control to regulators
sh: add fixed voltage regulators to se7724
sh: add fixed voltage regulators to sdk7786
sh: add fixed voltage regulators to rsk
sh: add fixed voltage regulators to migor
sh: add fixed voltage regulators to kfr2r09
sh: add fixed voltage regulators to ap325rxa
sh: add fixed voltage regulators to sh7757lcr
sh: add fixed voltage regulators to sh2007
...
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
Pull two ceph fixes from Sage Weil:
"The first patch fixes up the old crufty open intent code to use the
atomic_open stuff properly, and the second fixes a possible null deref
and memory leak with the crypto keys."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix crypto key null deref, memory leak
ceph: simplify+fix atomic_open
eCryptfs mount options do not
- Cleanups in the messaging code
- Better handling of empty files in the lower filesystem to improve usability.
Failed file creations are now cleaned up and empty lower files are converted
into eCryptfs during open().
- The write-through cache changes are being reverted due to bugs that are not
easy to fix. Stability outweighs the performance enhancements here.
- Improvement to the mount code to catch unsupported ciphers specified in the
mount options
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4vDd
-----END PGP SIGNATURE-----
Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
- Fixes a bug when the lower filesystem mount options include 'acl',
but the eCryptfs mount options do not
- Cleanups in the messaging code
- Better handling of empty files in the lower filesystem to improve
usability. Failed file creations are now cleaned up and empty lower
files are converted into eCryptfs during open().
- The write-through cache changes are being reverted due to bugs that
are not easy to fix. Stability outweighs the performance
enhancements here.
- Improvement to the mount code to catch unsupported ciphers specified
in the mount options
* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: check for eCryptfs cipher support at mount
eCryptfs: Revert to a writethrough cache model
eCryptfs: Initialize empty lower files when opening them
eCryptfs: Unlink lower inode when ecryptfs_create() fails
eCryptfs: Make all miscdev functions use daemon ptr in file private_data
eCryptfs: Remove unused messaging declarations and function
eCryptfs: Copy up POSIX ACL and read-only flags from lower mount
Pull CIFS update from Steve French:
"Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.
I am holding up a few more days on merging the remainder of the
SMB2/SMB2.1 enablement although it is nearing review completion, in
order to address some review comments from Jeff Layton on a few of the
subsequent SMB2 patches, and also to debug an unrelated cifs problem
that Pavel discovered."
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Add SMB2 support for rmdir
CIFS: Move rmdir code to ops struct
CIFS: Add SMB2 support for mkdir operation
CIFS: Separate protocol specific part from mkdir
CIFS: Simplify cifs_mkdir call
Borislav Petkov reports that the new warning added in commit
88fdf75d1b ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.
The call trace looks like this:
x86_64_start_kernel ->
x86_64_start_reservations ->
start_kernel ->
setup_arch ->
paging_init ->
zone_sizes_init ->
free_area_init_nodes ->
free_area_init_node
and (with the warning replaced by debug output), Borislav sees
On node 0 totalpages: 4193848
DMA zone: 64 pages used for memmap
DMA zone: 6 pages reserved
DMA zone: 3890 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 798464 pages, LIFO batch:31
Normal zone: 52736 pages used for memmap
Normal zone: 3322368 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 4423680 <----
On node 1 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 8617984 <----
On node 2 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 12812288 <----
On node 3 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
so remove the bogus warning for now to avoid annoying people. Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1
Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
SIRFSOC_TIMER_LATCH);
Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized. Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work. Replace it with a fresh
method. In particular:
* always attempt to do an atomic open+lookup, both for the create case
and for lookups of existing files.
* fix symlink handling by returning 1 to the VFS so that we can follow
the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>
setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull MIPS updates from Ralf Baechle:
"The lion share of this pull request are fixes for clk-related breakage
caused by other changes during this merge window. For some platforms
the fix was as simple as selecting HAVE_CLK, for others like the
Loongson 2 significant restructuring was required.
The remainder are changes required to get the Lantiq code to work
again."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Loongson 2: Sort out clock managment.
MIPS: Loongson 1: more clk support and add select HAVE_CLK
MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: Lantiq: Platform specific CLK fixup
MIPS: Lantiq: Add device_tree_init function
MIPS: Lantiq: Fix interface clock and PCI control register offset
Jiri Slaby