Pull input layer fix from Dmitry Torokhov:
"A small tweak for the Synaptics PS/2 touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add min/max quirk for Lenovo S540
Pull input subsystem fixes from Dmitry Torokhov:
"Just a couple touchpad drivers fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - do not reduce trackpoint speed by half
Input: elantech - add new icbody type
Input: elantech - fix detection of touchpads where the revision matches a known rate
On some v7 devices (e.g. Lenovo-E550) the deltas reported are typically
only in the 0-1 range dividing this by 2 results in a range of 0-0.
And even for v7 devices where this does not lead to making the trackstick
entirely unusable, it makes it twice as slow as before we added v7 support
and were using the ps/2 mouse emulation of the dual point setup.
If some kind of generic slowdown is actually necessary for some devices,
then that belongs in userspace, not in the kernel.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rico Moorman <rico.moorman@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds new icbody type to the list recognized by Elantech PS/2 driver.
Cc: stable@vger.kernel.org
Signed-off-by: Sam Hung <sam.hung@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.
This fixes the touchpad not being detected properly on Asus PU551LA
laptops.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The vmmouse Kconfig help text was referring to an incorrect user-space
driver version. Fix this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On v7 touchpads sometimes when 2 fingers are moved down on the touchpad
until they "fall of" the touchpad, the second touch will report 0 for y
(max y really since the y axis is inverted) and max x as coordinates,
rather then reporting 0, 0 as is expected for a non touching finger.
This commit detects this and treats these touches as non touching.
See the evemu-recording here:
https://bugzilla.redhat.com/attachment.cgi?id=1025058
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1221200
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the v3 hardware sees more than one finger, it uses the semi-mt
protocol to report the touches. However, it currently works when
num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1
finger as if num_fingers was 1.
This confuses userspace which knows how to deal with extra fingers
when all the slots are used, but not when some are missing.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have been testing wrong variable when trying to make sure that input
allocation succeeded.
Reported by Coverity (CID 1295918).
Acked-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVOyVhAAoJEIwa5zzehBx3U/gP/jEqIMKEB6r0qApnYLU/0v2V
6AiAtQBDZ6PSNDOqy5Mo5HoMQ0WI09n4xvml3Ntmx0/584RGECn8nlFvwlowIxNo
FLGYcKWuy8w8wKgN19hhEYySnTEex4+kBuDTITvya61SpvxUUfu7fpGV+DXwM2CS
aJQdMOwl24BJ4gjev9JS5QasyZrAzZVuDwo8vSKG6PKZNGgC1uyjOrm+NjiTEW15
FzCk77rRHfiN6Zr9C79ZfqV/nWKm4rPvaJJOiNr2vZUQ/0bhbvSHp3/BekjtnlOv
W6GbUCoDT6/DU/p1SP2Yegqk5pOEcqKQFe7Uc3YDSfiNLNCp03nF1RuIoi/NzfDy
1GcLYWAvHCrtmpQwqM/gIgc9uAsFN9Stin2G79xt3U/dUitdAmwMsCfqDE1FO63e
pGjPx0H7e1Ot3en3O5agaAlYlsokptKl3bIVOMfK6s6bH3RK4Y83LxwsVQKYkayA
TyulczOPnx6i4+acQroIwpFTj8QhhNjjhBU5gXTebVj4B/CwfieZBadaYF23O765
shX71oUJ1gQ6LCZtu8brl/82uk3sSkpVDi8e5WWaSnLfnAmqtU/ITy5yg77uuD0b
RAdHxVFUO6Y0FspWmWzBckrPec7ub+SKglCACq8HNciGx/9BWx6NUWI9FK93CDIu
O36D/l9hoUvA0gds5Iom
=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
Pull more input subsystem updates from Dmitry Torokhov:
- an update to Atmel MXT driver that makes it functional on Google
Pixel 2 boxes (both touchpad and touchscreen)
- a new VMware VMMouse driver that should allow us drop X vmmouse
driver that requires root privileges (since it accesses ioports)
- XBox One controllers now support force feedback (rumble)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: lm8333 - fix broken email address
Input: cyapa - fix setting suspend scan rate
Input: elan_i2c - fix calculating number of x and y traces.
Input: elan_i2c - report hovering contacts
Input: elants_i2c - zero-extend hardware ID in firmware name
Input: alps - document separate pointstick button bits for V2 devices
Input: atmel_mxt_ts - add support for Google Pixel 2
Input: xpad - add rumble support for Xbox One controller
Input: ff-core - use new debug macros
Input: add vmmouse driver
Input: elan_i2c - adjust for newer firmware pressure reporting
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: Dudley Du <dudl@cypress.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cycle:
- A new GPIO hogging mechanism has been added. This can
be used on boards that want to drive some GPIO line high,
low, or set it as input on boot and then never touch it
again. For some embedded systems this is bliss and
simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs
in bulk as was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header
any GPIO driver needs to include or something is wrong.
Cleanups restricting drivers to this include are welcomed
if tested.
- Sort the GPIO Kconfig and split it into submenus, as
it was becoming and unstructured, illogical and
unnavigatable mess. I hope this is easier to follow.
Menus that require a certain subsystem like I2C can
now be hidden nicely for example, still working on
others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and
F71869A variants.
- The MIPS Loongson driver has been moved to
drivers/gpio for consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is
a "hard IP" block from Synopsys which has started to
turn up in so diverse architectures as X86 Quark, ARC
and a slew of ARM systems. So even though it's not an
expander, it's generic enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long
discussion with Daniel Vetter et al, tracing back to
the shootout at the kernel summit where DRM drivers
and sub-componentization was discussed. In this case
a mock GPIO is assumed to be the best compromise
gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's
see.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QFbC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in
Google Pixel 2 (2015).
While newer version of ACPI standard allow use of device-tree-like
properties in device descriptions, the version of ACPI implemented in
Google BIOS does not support them, and we have to resort to DMI data to
specify exact characteristics of the devices (touchpad vs. touchscreen,
GPIO to button mapping, etc).
Pixel 1 continues to use i2c devices and platform data created by
chromeos-laptop driver, since ACPI does not enumerate them.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"You will get the following new drivers:
- Qualcomm PM8941 power key drver
- ChipOne icn8318 touchscreen controller driver
- Broadcom iProc touchscreen and keypad drivers
- Semtech SX8654 I2C touchscreen controller driver
ALPS driver now supports newer SS4 devices; Elantech got a fix that
should make it work on some ASUS laptops; and a slew of other
enhancements and random fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: alps - non interleaved V2 dualpoint has separate stick button bits
Input: alps - fix touchpad buttons getting stuck when used with trackpoint
Input: atkbd - document "no new force-release quirks" policy
Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
Input: ALPS - V7 devices can report 5-finger taps
Input: ALPS - add support for SS4 touchpad devices
Input: ALPS - refactor alps_set_abs_params_mt()
Input: elantech - fix absolute mode setting on some ASUS laptops
Input: atmel_mxt_ts - split out touchpad initialisation logic
Input: atmel_mxt_ts - implement support for T100 touch object
Input: cros_ec_keyb - fix clearing keyboard state on wakeup
Input: gscps2 - drop pci_ids dependency
Input: synaptics - allocate 3 slots to keep stability in image sensors
Input: Revert "Revert "synaptics - use dmax in input_mt_assign_slots""
Input: MT - make slot assignment work for overcovered solutions
mfd: tc3589x: enforce device-tree only mode
Input: tc3589x - localize platform data
Input: tsc2007 - Convert msecs to jiffies only once
Input: edt-ft5x06 - remove EV_SYN event report
Input: edt-ft5x06 - allow to setting the maximum axes value through the DT
...
This adds rumble support for Xbox One controller by sending continuous
rumble command. Trigger button rumbling is not yet implemented.
Signed-off-by: Ming-ting Yao Wei <mwei@lxde.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
VMMouse enables low-latency mouse-cursor-movements for VMWare and QEMU
guests. By removing the guest cursor and using the host as a guest cursor
the cursor movement appears instant although in reality there is some lag.
To be able to do this, the host's view of the cursor position must exactly
match the guest's view and an absolute pointer device is needed. Enter the
VMMouse. While the VMMouse driver has historically been an Xorg user-space
driver, implementing it as a kernel imput driver enables rootless Xorg and
new compositing display servers for VMware guests.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get pressure format flag from firmware to check if we need to normalize
pressure data before reporting it.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
Non interleaved V2 dualpoint touchpad / stick combos have separate stick
button bits in the touchpad packets, if we do not check these then the
trackpoint buttons will not work when using the touchpad, and when pressed
when the user starts using the touchpad will report a release event even
though the button is still pressed.
This commit fixes this by checking the separate bits, note that we simply
combine the buttons, since the hardware does the same when using the touchpad
buttons with the trackpoint, so we do not have enough information to properly
separate them.
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the left touchpad button gets pressed, and then the trackpoint is
moved, and then the button is released, the following happens:
1) touchpad packet is received, touchpad evdev node reports BTN_LEFT 1
2) pointing stick packet is received, the hw will report a BTN_LEFT 1 in
this packet because when the trackstick is active it communicates the
combined touchpad + pointing stick buttons in the trackstick packet,
since alps_report_bare_ps2_packet passes NULL (*) for the dev2 parameter
to alps_report_buttons the combining is not detected and the
pointing stick evdev node will also report BTN_LEFT 1
3) on release of the button a pointing stick packet with BTN_LEFT 0 is
received and the pointing stick evdev node will report BTN_LEFT 0
Note how because of the passing as NULL for dev2 the touchpad evdev node
will never send BTN_LEFT 0 in this scenario leading to a stuck mouse button.
This is a regression in 4.0 introduced by commit 04aae283ba
("Input: ALPS - do not mix trackstick and external PS/2 mouse data")
This commit fixes this by passing in the touchpad evdev as dev2 parameter
when calling alps_report_buttons for the pointingstick on alps v2 devices,
so that alps_report_buttons correctly detect that we're already reporting
the button as pressed via the touchpad evdev node, and will also send the
release event there.
Cc: stable@vger.kernel.org # 4.0
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To save people some time let's document that we do not want new quirks for
"force-release" keys in the kernel and that they should patch userspace
(udev) instead.
Suggested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a kernel panic which occurs when buf_list is empty. This can
happen occasionally when user space is under heavy load (e.g. due to image
processing on the CPU) and new buffers aren't re-queued fast enough. In that
case, vb2_start_streaming_called can return true, but when the spinlock
is taken and sur40_poll attempts to fetch the next buffer from buf_list, the
list is in fact empty.
This patch needs to be applied on top of the queued one adding V4L2 support
to the sur40 driver.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for SS4 touchpad devices as ALPS_PROTO_V8
protocol. They are real multi-touch devices and can be found in TOSHIBA
Tecra C50.
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for adding support for SS4 touchpads, let's split
alps_set_abs_params_mt into common, v7-specific, and other protocols
portions.
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVIws/AAoJEHm+PkMAQRiGwEcH/1GCBqrBzXaKwDdCPMRcYVUb
MYkXmGkCGRYWe5MXI8QNAaa/CdG6mAFMHWN6CaMMpLTxnM1m87uBg01fQMsh73BO
mRVLKE/soiJDnR1gYzBBDBYV/AUvytN5PhgeNaA95YIJvU3T1f3iTnV8vs30Dp0L
YpxSqwr3C0k7C9IE0VcgfzvWJPCnQ9IWHuX3jn5s1XjGKVNbBYHMt6FusHdyXMfT
dp8ksuGHwm30mTFI5xJpKOrRzfi+P5EsEUrsnFRPRM/iFTVrM5R7eaUhsRZb2+Wo
YApnbYhUYz7om1AuQ+UZ/+S6y7ZLlGWegI1lWI754GIsczG5vPHEYhhgkzMhTsc=
=kR1V
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc7' into next
Sync up with Linux 4.0-rc7 to bring in ALPS changes.
The case occurred recently with a touchscreen using twice a slot during a
single EV_SYN event:
E: 0.288415 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
E: 0.296207 0003 002f 0000 # EV_ABS / ABS_MT_SLOT 0
E: 0.296207 0003 0039 -001 # EV_ABS / ABS_MT_TRACKING_ID -1
E: 0.296207 0003 002f 0001 # EV_ABS / ABS_MT_SLOT 1
E: 0.296207 0003 0035 0908 # EV_ABS / ABS_MT_POSITION_X 908
E: 0.296207 0003 0036 1062 # EV_ABS / ABS_MT_POSITION_Y 1062
E: 0.296207 0003 002f 0000 # EV_ABS / ABS_MT_SLOT 0
E: 0.296207 0003 0039 8787 # EV_ABS / ABS_MT_TRACKING_ID 8787
E: 0.296207 0003 0035 1566 # EV_ABS / ABS_MT_POSITION_X 1566
E: 0.296207 0003 0036 0861 # EV_ABS / ABS_MT_POSITION_Y 861
E: 0.296207 0003 0000 0908 # EV_ABS / ABS_X 908
E: 0.296207 0003 0001 1062 # EV_ABS / ABS_Y 1062
E: 0.296207 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
This occurred because while having already slots 0 and 1 assigned, the
touchscreen sent:
0.293377 Tip Switch: 0 | Contact Id: 0 | X: 539 | Y: 1960 | Contact Count: 3
0.294783 Tip Switch: 1 | Contact Id: 1 | X: 908 | Y: 1062 | Contact Count: 0
0.296187 Tip Switch: 1 | Contact Id: 2 | X: 1566 | Y: 861 | Contact Count: 0
Slot 0 is released correclty, but when we look for Contact ID 2, the slot
0 is then picked up again because it is marked as inactive (trackingID < 0).
This is wrong, and we should not reuse a slot in the same frame.
The test should also check for input_mt_is_used().
In addition, we need to initialize mt->frame to an other value than 0.
With mt->frame being 0, all slots are tags as currently used, and so
input_mt_get_slot_by_key() would return -1 for all requests.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=88903
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem - two more tweaks for ALPS driver to
work out kinks after splitting the touchpad, trackstick, and potential
external PS/2 mouse into separate input devices.
Changes to support ALPS SS4 devices (protocol V8) will be coming in
4.1..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - document stick behavior for protocol V2
Input: alps - report V2 Dualpoint Stick events via the right evdev node
Input: alps - report interleaved bare PS/2 packets via dev3
If the "linux,gpio-keymap" DT property is defined, the T19 keys are
configured and the device is setup as a touchpad rather than a touchscreen.
The logic is part of the input device initialization routine but it can be
factored out to its own function to simplify the former.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the new T100 object which replaces the previous T9
multitouch touchscreen object in recent maXTouch devices. T100 provides
improved reporting with selectable auxiliary information, and a type field
for hover/stylus/glove reporting.
The hovering finger support was based on Chung-Yih's work in the ChromiumOS
downstream kernel:
https://chromium-review.googlesource.com/#/c/219280/
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
[javier: Factor out T9 and T100 init functions and rework hover support]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the comment right before explains, the keyboard state is to be cleared
only if the EC wasn't a wakeup source in the last suspend.
Without this commit, there's an unneeded delay when resuming from suspend
and we also lose the key that was pressed while suspended.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver does not use any PCI IDs, don't include the pci_ids.h header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds