Sigma Designs chips use a variant of this controller with the following
differences:
- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts
This patch adds support for the first two of these. It also calculates
and sets the correct clock divisor if a clk is provided. The bus
frequency is optionally speficied in the device tree node.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions. Plain convert, no functionality
added yet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe function is a little bit messy, something here, something
there. Rework it so that there is some order: first init the private
structure, then the adapter, then do HW init. This also allows us to
remove the device argument of the clock calculation function, because it
now can be deduced from the private structure. Also, shorten some lines
where possible. This is a preparation for further refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inspired from the i2c-rk3x driver (thanks guys!) but refactored and
extended. See built-in docs for further information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Also, sort the properties alphabetically and make indentation
consistent. Wording largely taken from i2c-rk3x.txt, thanks guys!
Only "i2c-scl-internal-delay-ns" is new, the rest is used by two drivers
already and was documented in their driver binding documentation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the I2C adapter devices of_node to that of the PCI device, such that
I2C clients may be instantiated via device tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For platform with auto restart support, between every transfer,
i2c controller will trigger an interrupt and SW need to handle
it to start new transfer. When doing write-then-read transfer,
instead of restart mechanism, using WRRD mode to have controller
send both transfer in one request to reduce latency.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The suspended flag is a flag holding the device's PM status.
The runtime framework does that for us.
Use pm_runtime_suspended call instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the clocks are enabled at probe and disabled at remove.
Which keeps the clocks enabled even if no transaction is going on.
This patch enables the clocks at the start of transfer and disables
after it.
Also adapts to runtime pm.
converts dev pm to const to silence a checkpatch warning.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds a i2c_check_quirks helper function to check the quirk flags
of an i2c adapter, in a similar way to i2c_check_functionality.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported in the links given below. the BCM2835 has a hardware bug in
its i2c module which prevents a correct clock stretching. This patch
adds the I2C_AQ_NO_CLK_STRETCH quirk flag to i2c-bcm2835.
Signed-off-by: Nicola Corna <nicola@corna.info>
[wsa: put the links into the code as comments]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C_AQ_NO_CLK_STRETCH to drivers/i2c/algos/i2c-algo-bit.c when getscl
is not available.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C_AQ_NO_CLK_STRETCH quirk flag, to be used when clock stretching is
not supported.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All protected sections are only called from sleep-able context, so there is
no need to use a spinlock.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The simple_strtoul function is marked as obsolete.
This patch replace it by kstrtou8.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for port names for the SB800 chipset.
Since the chipset supports a multiplexed main SMBus controller, adding
the channel name to the adapter name is necessary to differentiate the
ports better (for example in sensors output).
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. The multiplexed ports share the same SMBus address and
register set. The port is selected by bits 2:1 of the smb_en register
(0x2C).
Only one port can be active at any point in time therefore a mutex is
needed in order to synchronize access.
Additionally, the commit avoids requesting and releasing the SMBus base
address index region on every multiplexed transfer by moving the
request_region call into piix4_probe.
Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
support to access sensor data from the w83795adg).
Cc: Thomas Brandon <tbrandonau@gmail.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. Therefore the static variable piix4_main_adapter is
converted into a piix4_main_adapters array that can hold one
i2c_adapter for each multiplexed port.
The auxiliary adapter remains unchanged since it represents the second
(not multiplexed) SMBus controller on the SB800 chipset.
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.
Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull nouveau and radeon fixes from Dave Airlie:
"Just some nouveau and radeon/amdgpu fixes.
The nouveau fixes look large as the firmware context files are
regenerated, but the actual change is quite small"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: make some dpm errors debug only
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
drm/radeon: make rv770_set_sw_state failures non-fatal
drm/amdgpu: move dependency handling out of atomic section v2
drm/amdgpu: optimize scheduler fence handling
drm/amdgpu: remove vm->mutex
drm/amdgpu: add mutex for ba_va->valids/invalids
drm/amdgpu: adapt vce session create interface changes
drm/amdgpu: vce use multiple cache surface starting from stoney
drm/amdgpu: reset vce trap interrupt flag
Two fixes for the ds1307 alarm and wakeup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6IeZ
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
Pull MIPS fix from Ralf Baechle:
"Just a fix for empty loops that may be removed by non-antique GCC"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix delay loops which may be removed by GCC.
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Add missing initialization of max_pfn, which is needed to make
selftests/vm/mlock2-tests succeed,
- Wire up new mlock2 syscall"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up mlock2
m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: m54xx - Add missing initialization of max_pfn
m68k/mm: motorola - Add missing initialization of max_pfn
Pull ARM fixes from Russell King:
"Just two changes this time around:
- wire up the new mlock2 syscall added during the last merge window
- fix a build problem with certain configurations provoked by making
CONFIG_OF user selectable"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8454/1: OF implies OF_FLATTREE
ARM: wire up mlock2 syscall
Pull SCSI target fixes from Nicholas Bellinger:
- fix tcm-user backend driver expired cmd time processing (agrover)
- eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
- fix iscsi login kthread failure case hung task regression (nab)
- fix COMPARE_AND_WRITE completion use-after-free race (nab)
- fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
SGL offset data corruption. (Jan + Doug)
- fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
(Himanshu + HCH)
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/stat: print full t10_wwn.model buffer
target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
qla2xxx: Fix regression introduced by target configFS changes
kref: Remove kref_put_spinlock_irqsave()
target: Invoke release_cmd() callback without holding a spinlock
target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
iscsi-target: Fix rx_login_comp hang after login failure
iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
target/user: Do not set unused fields in tcmu_ops
target/user: Fix time calc in expired cmd processing
Pull thermal management fixes from Zhang Rui:
"Specifics:
- several fixes and cleanups on Rockchip thermal drivers.
- add the missing support of RK3368 SoCs in Rockchip driver.
- small fixes on of-thermal, power_allocator, rcar driver, IMX, and
QCOM drivers, and also compilation fixes, on thermal.h, when thermal
is not selected"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
imx: thermal: use CPU temperature grade info for thresholds
thermal: fix thermal_zone_bind_cooling_device prototype
Revert "thermal: qcom_spmi: allow compile test"
thermal: rcar_thermal: remove redundant operation
thermal: of-thermal: Reduce log level for message when can't fine thermal zone
thermal: power_allocator: Use temperature reading from tz
thermal: rockchip: Support the RK3368 SoCs in thermal driver
thermal: rockchip: consistently use int for temperatures
thermal: rockchip: Add the sort mode for adc value increment or decrement
thermal: rockchip: improve the conversion function
thermal: rockchip: trivial: fix typo in commit
thermal: rockchip: better to compatible the driver for different SoCs
dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible
Cut 'n paste error saw it only process sizeof(t10_wwn.vendor) characters.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Given the following sample LIO subtopology,
% targetcli ls /loopback/
o- loopback ................................. [1 Target]
o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
o- luns ................................... [2 LUNs]
o- lun0 ................ [iblock/ram0 (/dev/ram0)]
o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3
[3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4
the following bug can be observed in Linux 4.3 and 4.4~rc1:
% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
00000200
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
this patch fixes following regression
# targetcli
[Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'
Fixes: 2eafd72939 ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The last user is gone. Hence remove this function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Måns Rullgård