Setting the transfer length in the TRANSACTION register after the
CONTROL register is programmed causes intermittent timeout issues in
SPFI transfers when using the SPI framework to control the CS GPIO
lines. To avoid this issue, set transfer length before programming
the CONTROL register.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a driver doesn't implement the master->handle_err() callback and an
SPI transfer fails, the kernel will crash with a NULL pointer
dereference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0003000
[00000000] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 80000206 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc7-koelsch-05861-g1fc9fdd4add4f783 #1046
Hardware name: Generic R8A7791 (Flattened Device Tree)
task: eec359c0 ti: eec54000 task.ti: eec54000
PC is at 0x0
LR is at spi_transfer_one_message+0x1cc/0x1f0
Make the master->handle_err() callback optional to avoid the crash.
Also fix a spelling mistake in the callback documentation while we're at
it.
Fixes: b716c4ffc6 ("spi: introduce master->handle_err() callback")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the SPFI BITCLK divider supports a value of up to 255, only
values up to 128 are usable. This results in a maximum possible bit
clock rate of 1/4th the input clock rate.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for switching to using the SPI core's CS GPIO handling,
move setup of the PORT_STATE register, which must be configured before
CS is asserted, to a prepare_message() callback.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add delay between chip select and clock signals, before clock starts and
after clock stops.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous algorithm had an outer loop with the values {2,3,5,7} and an
inner loop with {2,4,6,8,16,32,...,32768}, and would pick the first
value over the required scaling value (where the total scale was the two
numbers multiplied).
Since the inner loop went up to 32768 it would always pick a value of 2
for PBR and a much higher than necessary value for BR. The desired
scale factor was being divided by two I believe to compensate for the
much higher scale factors (the divide by two not specified in the
reference manual).
Updated to check all values and find the smallest scale factor possible
without going over the desired clock rate.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need "ret" to be unsigned for the error handling to work. The
signedness of "i" and "n" don't matter but qspi_set_send_trigger()
returns an int so I've changed them to int as well.
Fixes: 4b6fe3edcb ('spi: Using Trigger number to transmit/receive data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
They are used to decide if the controller can do DMA on a buffer
of a specific length and thus are needed before any transfer is attempted.
This fixes a memory leak where the SPI core uses the drivers can_dma()
callback to determine if a buffer needs to be mapped. As the watermark
levels aren't correct at that point the driver falsely claims to be able to
DMA the buffer when it fact it isn't.
After the transfer has been done the core uses the same callback to
determine if it needs to unmap the buffers. As the driver now correctly
claims to not being able to DMA the buffer the core doesn't attempt to
unmap the buffer which leaves the SGT leaking.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
cr_width may be not initialized before using by cr, the related warning
(with defconfig under blackfin by gcc5):
CC drivers/spi/spi-bfin5xx.o
drivers/spi/spi-bfin5xx.c: In function 'bfin_spi_pump_transfers':
drivers/spi/spi-bfin5xx.c:655:5: warning: 'cr_width' may be used uninitialized in this function [-Wmaybe-uninitialized]
cr |= cr_width;
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation of bitbang_txrx_be_cpha0 and
bitbang_txrx_be_cpha1 always call setmosi. That runs into several
unnecessary calls into the gpiolib when the level of the GPIO actually
has not to be changed.
This patch changes the routines to remember the last GPIO level
and only calls setmosi if an change has to be made. This
way it improves the transfer throughput.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We refactored this code but accidentally left out a break statement so
QUARK_X1000_SSP isn't handled correctly.
Fixes: 025ffe88ee ('spi: pxa2xx: shift clk_div in one place')
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous algorithm had an outer loop with the values {2,3,5,7} and an
inner loop with {2,4,6,8,16,32,...,32768}, and would pick the first
value over the required scaling value (where the total scale was the two
numbers multiplied).
Since the inner loop went up to 32768 it would always pick a value of 2
for PBR and a much higher than necessary value for BR. The desired
scale factor was being divided by two I believe to compensate for the
much higher scale factors (the divide by two not specified in the
reference manual).
Updated to check all values and find the smallest scale factor possible
without going over the desired clock rate.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to transmit and receive data when have 32 bytes of data that
ready has prepared on Transmit/Receive Buffer to transmit or receive.
Instead transmits/receives a byte data using Transmit/Receive Buffer
Data Triggering Number will improve the speed of transfer data.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce the number of interrupts/message we fill the FIFO before
enabling interrupts - for short messages this reduces the interrupt count
from 2 to 1 interrupt.
There have been rare cases where short (<200ns) chip-select switches with
native CS have been observed during such operation, this is why this
optimization is only enabled for GPIO-CS.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since spidev is a detail of how Linux controls a device rather than a
description of the hardware in the system we should never have a node
described as "spidev" in DT, any SPI device could be a spidev so this
is just not a useful description.
In order to help prevent users from writing such device trees generate a
warning if spidev is instantiated as a DT node without an ID in the match
table.
Signed-off-by: Mark Brown <broonie@kernel.org>
This also allows for GPIO-CS to get used removing the limitation of
2/3 SPI devises on the SPI bus.
Fixes: spi-cs-high with native CS with multiple devices on the spi-bus
resetting the chip selects to "normal" polarity after a finished
transfer.
No other functionality/improvements added.
Tested with the following 4 devices on the spi-bus:
* mcp2515 with native CS
* mcp2515 with gpio CS
* fb_st7735r with native CS
(plus spi-cs-high via transistor inverting polarity)
* enc28j60 with gpio-CS
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have found that we can sometimes see read failures on boards with
high-capacitance SPI lines. It seems that the controller samples the Rx
data line too early, and its register interface has an "Rx Sample Delay"
setting to fine-tune against this issue.
This patch adds a new optional device tree entry that can configure this
delay in terms of nanoseconds. The kernel will calculate the
best-fitting amount of parent clock ticks to program the controller with
based on that.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Rockchip SPI driver currently calculates its clock rate divisor by
integer dividing the parent rate by the target rate, and then rounding
the result up to the next even number (since the divisor must be
even).
Clock rate divisors should always be rounded up, so that the resulting
frequency is lower or equal to the target. This is correctly done in the
second step here but not in the first, so we still have a risk of
exceeding the desired target frequency (e.g. setting spi-max-frequency
to 40000000 with a parent clock of 99000000 could lead to a divisor of
99000000 / 40000000 == 2 (which is even) that then results in an
effective frequency of 99000000 / 2 == 49500000 (potentially exceeding
the flash chip's specifications).
This patch changes the division to round up to fix this problem.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trying to register an SPI device asynchronously (via async_schedule() call)
results in an ugly complaint from request_module() warning about potential
deadlock (because request_module tries to wait for async works to
complete, the caller is also an async work in this case).
While we could try to switch to using request_module_nowait(), other buses,
as well as SPI itself when not using device tree, do not try to load
modules explicitly, but rather rely on the standard infrastructure (such as
udev) to execute module loading. There is no reason why SPI OF-described
devices should be treated differently.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 1a7b7ee72c (spi: Ensure that CS line is in non-active state after
spi_setup()) introduces an unconditional call of spi_set_cs() before ->setup().
The dw_spi_set_cs() relies on that fact that ->setup() is already called, but
it doesn't now. This patch fixes the crash by adding an additional check to
dw_spi_set_cs().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Quark SoC data sheet describes the baud rate setting using fractional
divider. The subset of possible values represented by a table suggests that the
divisor has one block that could divide by 5. This explains the number of the
beast in some cases in the table. Thus, in this particular case the divisor can
be evaluated as
5^i * 2^j * 2 * k,
where
i = [0, 1]
j = [0, 23]
k = [1, 256]
There are few cases as mentioned in the data sheet, i.e. better form of the
clock signal will be in case if DDS_CLK_RATE either 2^n or 2/5. It's also
possible to use any value that is less or equal to 0x33333 (1/5/16 = 1/80).
All three cases are compared to each other and the one that suits better is
chosen by the approximation algorithm. Anyone can play with the script [1] that
represents the algorithm.
[1] https://gist.github.com/06b084488b3629898121
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refactors ssp_get_clk_div() and pxa2xx_ssp_get_clk_div() to align
clk_div calculations, i.e. ssp_get_clk_div() and quark_x1000_set_clk_regvals()
will return plain clk_div and it will be shifted to proper position in
pxa2xx_ssp_get_clk_div().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
`spidev_message()` sums the lengths of the individual SPI transfers to
determine the overall SPI message length. It restricts the total
length, returning an error if too long, but it does not check for
arithmetic overflow. For example, if the SPI message consisted of two
transfers and the first has a length of 10 and the second has a length
of (__u32)(-1), the total length would be seen as 9, even though the
second transfer is actually very long. If the second transfer specifies
a null `rx_buf` and a non-null `tx_buf`, the `copy_from_user()` could
overrun the spidev's pre-allocated tx buffer before it reaches an
invalid user memory address. Fix it by checking that neither the total
nor the individual transfer lengths exceed the maximum allowed value.
Thanks to Dan Carpenter for reporting the potential integer overflow.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The official documentation is wrong in this respect.
Has been tested empirically for dividers 2-1024
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement the recommendation from the BCM2835 data-sheet
with regards to polling drivers to fill/drain the FIFO as much data as possible
also for the interrupt-driven case (which this driver is making use of).
This means that for long transfers (>64bytes) we need one interrupt
every 64 bytes instead of every 12 bytes, as the FIFO is 16 words (not bytes) wide.
Tested with mcp251x (can bus), fb_st7735 (TFT framebuffer device)
and enc28j60 (ethernet) drivers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
asm/irq.h is already included by linux/interrupt.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These asm/io.h, asm/irq.h and asm/delay.h are needless since they are
already included by linux/io.h via drivers/spi/spi-pxa2xx.h,
linux/interrupt.h and linux/delay.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the endian agnositc IO functions instead of the __raw ones for when
the driver is in use on big-endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The following errors/warnings issued by checkpatch.pl --strict have been fixed:
drivers/spi/spi-bcm2835.c:182: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:191: CHECK: braces {} should be used on all arms of this statement
drivers/spi/spi-bcm2835.c:234: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:256: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:271: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:346: CHECK: Alignment should match open parenthesis
total: 0 errors, 0 warnings, 6 checks, 403 lines checked
In 2 locations the arguments had to get split/moved to the next line so that the
line width stays below 80 chars.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Altera's Arria10 SoC interconnect requires a 32-bit write for APB
peripherals. The current spi-dw driver uses 16-bit accesses in
some locations. This patch converts all the 16-bit reads and
writes to 32-bit reads and writes.
Additional Documentation to Support this Change:
The DW_apb_ssi databook states:
"All registers in the DW_apb_ssi are addressed at 32-bit boundaries
to remain consistent with the AHB bus. Where the physical size of
any register is less than 32-bits wide, the upper unused bits of
the 32-bit boundary are reserved. Writing to these bits has no
effect; reading from these bits returns 0." [1]
[1] Section 6.1 of dw_apb_ssi.pdf (version 3.22a)
Request for test with platforms using the DesignWare SPI IP.
Tested On:
Altera CycloneV development kit
Altera Arria10 development kit
Compile tested for build errors on x86_64 (allyesconfigs)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the omap100k driver uses prepare and unprepare transfer hardware
to enable and disable clocks for the IP block. Since these functions are
called along with runtime PM and end up duplicating its functionality in a
less flexible fashion we are trying to phase them out so convert this
driver to do runtime PM instead.
While doing so add missing error handling and remove a redundant NULL
assignment.
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices samples state of the chip select signal during power up
and act differently based on this state, so SPI core should ensure
that CS line is driven in non-active state after spi_setup().
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of clearing the RxU, RxO, and TxO IRQs individually with
3 register reads, a single read of the ICR register will do the
same thing.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
intel_mid_dma seems to be unmaintained for a long time. Moreover, the IP block
of DMA itself is the same in both dw_dmac and intel_mid_dma. This patch moves
spi-dw-midpci to use dw_dmac driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core has a comprehensive function set to map and unmap a message when it's
needed. This patch converts driver to use that advantage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch shuts up any ongoing DMA transfer in case of error.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In according to documentation SPI in DMA mode may encounter underrun/overrun
failures in rare cases. When such failure occurs, an error recovery protocol is
expected to be implemented in the device driver so that the failed transaction
can be restarted.
This patch enables FIFO overrun / underrun interrupts in DMA case and adds a
handler for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch splits DMA preparatory code to dma_setup() callback. The change also
converts transfer_one() to program DMA whenever the transfer is DMA mapped. The
change is a follow up of the converion to use SPI core transfer_one_message().
Since the DMA mapped transfers can be interleaved with PIO ones the DMA related
configuration should respect that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine has a specific type to be used for bus width. This patch converts the
code to use the values of the specific type when configure DMA transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove Kconfig dependency and enable driver for
all ARCHs.
Also update help description.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All SPI drivers have been converted from legacy suspend/resume callbacks to
dev_pm_ops. So we can finally remove support for legacy PM from the SPI
core.
Since there aren't any special bus specific things to do during
suspend/resume and since the PM core will automatically fallback directly to
using the device's PM ops if no bus PM ops are specified there is no need to
have any special SPI bus PM ops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of DMA completion is broken now since test_and_clear_bit() never
returns the other bit is set. It means condition are always false and we have
spi_finalize_current_transfer() called per each DMA completion which is wrong.
The patch fixes logic by clearing BUSY bit first and then check for the other
one.
Fixes: 30c8eb52cc (spi: dw-mid: split rx and tx callbacks when DMA)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch adds DMA capabilities to the spi-qup driver. If DMA channels are
present, the QUP will use DMA instead of block mode for transfers to/from SPI
peripherals for transactions larger than the length of a block.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com
Signed-off-by: Mark Brown <broonie@kernel.org>
num-cs is 32 bit property, don't read just upper 16 bits.
Fixes: 4a8573abe9 (spi: qup: Remove chip select function)
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch removes a lot of duplicate code since SPI core provides a nice
message handling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refactors the code in pump_transfers() to reprogram the registers
immediately when we have a new configuration data. The behaviour is slightly
modified:
- chip is always disabled and reenabled
- CTRL0 is always reprogrammed
This change allows to do a further refactoring and simplier conversion to use
SPI core DMA routines in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error handling is partially broken since the controller is disabled on
error and is not re-enabled until condition occurs, i.e. mode (poll, PIO/DMA),
chip (cs_change), or speed (clk_div) is changed. In the result of these changes
we will have a predictable state of the SPi controller independently on how
successfull was a previous transfer.
The patch disables interrupts and re-enables the SPI controller wherever it
needs to be done. Thus most of the time the SPI controller is kept enabled. The
runtime PM, when it will be implemented, must take care of the controller
disabling and re-enabling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"flag" variable does nothing, remove it.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PL022 Programmers model explicitely states "do not modify undefined register
bits". Correct the "all enable" interrupt mask so that it only enables defined
ones.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to PL022 specification, TNF bit states for "Transmit FIFO Not full".
So the logic here is inverted. But "Receive Overrun Interrupt", which is handled
here, is only triggered on Rx errors. So instead of fixing the if statement,
remove the whole message.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There was handle_err() callback introduced that is dedicated for error
handling. The patch moves error handling to this callback.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This callback would be useful to handle an error that occurs in the generic
implementation of transfer_one_message(). The good candidate for this is to
drain FIFO and / or to terminate DMA transfers when timeout happened.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DMA descriptor allocation fails we should not try to assign any fields in
the bad descriptor. The patch adds the necessary checks for that.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Removing the udelay between setting and clearing the soft reset bit in
the spfi control register as it is not required.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maximum transfer length supported by SPFI is 65535, this is limited
by the number of bits available in SPFI TSize register to represent
the transfer size.
For transfer requests larger than the maximum supported the driver
will return an invalid argument error.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The fourth argument of dmaengine_prep_slave_sg needs to be of the
enumeration type dma_transfer_direction instead of dma_data_direction.
Since the used enumeration values actually stay the same, this is not
an actual issue at runtime.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The commit d297933cc7 (spi: dw: Fix detecting FIFO depth) tries to fix the
logic of the FIFO detection based on the description on the comments. However,
there is a slight difference between numbers in TX Level and TX FIFO size.
So, by specification the FIFO size would be in a range 2-256 bytes. From TX
Level prospective it means we can set threshold in the range 0-(FIFO size - 1)
bytes. Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
This patch fixes it eventually right.
Fixes: d297933cc7 (spi: dw: Fix detecting FIFO depth)
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instead of an additional reading from the register let's update it even if the
value is kept the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch does the following changes:
a) the calculation of clk_div is simplified to oneliner;
b) chip->clk_div is updated if clk_div is not zero, therefore the condition is
simplified by using chip->clk_div in both cases;
c) while here, the redundant parentheses are removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to have an additional variable to get a TX level. The patch
refactors this piece of code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no sense to keep a member assignment in the internal structure inside
the condition which reprograms HW. It makes code readability better if kept
outside of the condition.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit d58cf5ff65 brought a second controller to the list of supported
devices and changed a number of the chip selects. Besides the previous number
was wrong anyway the mentioned patch makes it wrong again meanwhile has a
proper numbers in the commit message. Indeed, SPI1 has 5 bits and SPI2 has 2
bits, but it does not mean to have power of two of this bits as a possible
number of the chip selects. So, this patch fixes it eventually.
Fixes: d58cf5ff65 (spi: dw-pci: describe Intel MID controllers better)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch changes the way space is reserved in spidev's pre-allocated
TX and RX bounce buffers to avoid wasting space in the buffers for an
SPI message consisting of multiple, half-duplex transfers in different
directions.
Background:
spidev data structures have separate, pre-allocated TX and RX bounce
buffers (`spidev->tx_buffer` and `spidev->rx_buffer`) of fixed size
(`bufsiz`). The `SPI_IOC_MESSAGE(N)` ioctl processing uses a kernel
copy of the N `struct spi_ioc_transfer` elements copied from the
userspace ioctl arg pointer. In these elements: `.len` is the length of
transfer in bytes; `.rx_buf` is either a userspace pointer to a buffer
to copy the RX data to or is set to 0 to discard the data; and `.tx_buf`
is either a userspace pointer to TX data supplied by the user or is set
to 0 to transmit zeros for this transfer.
`spidev_message()` uses the array of N `struct spi_ioc_transfer`
elements to construct a kernel SPI message consisting of a `struct
spi_message` containing a linked list (allocated as an array) of N
`struct spi_transfer` elements. This involves iterating through the
`struct spi_ioc_transfer` and `struct spi_transfer` elements (variables
`u_tmp` and `k_tmp` respectively). Before the first iteration,
variables `tx_buf` and `rx_buf` point to the start of the TX and RX
bounce buffers `spidev->tx_buffer` and `spidev->rx_buffer` and variable
`total` is set to 0. These variables keep track of the next available
space in the bounce buffers and the total length of the SPI message.
Each iteration checks that there is enough room left in the buffers for
the transfer. If `u_tmp->rx_buf` is non-zero, `k_tmp->rx_buf` is set to
`rx_buf`, otherwise it remains set to NULL. If `u_tmp->tx_buf` is
non-zero, `k_tmp->tx_buf` is set to `tx_buf` and the userspace TX data
copied there, otherwise it remains set to NULL. The variables `total`,
`rx_buf` and `tx_buf` are advanced by the length of the transfer.
The "problem":
While iterating through the transfers, the local bounce buffer "free
space" pointer variables `tx_buf` and `rx_buf` are always advanced by
the length of the transfer. If `u_tmp->rx_buf` is 0 (so `k_tmp->rx_buf`
is NULL), then `rx_buf` is advanced unnecessarily and that part of
`spidev->rx_buffer` is wasted. Similarly, if `u_tmp->tx_buf` is 0 (so
`k_tmp->tx_buf` is NULL), part of `spidev->tx_buffer` is wasted.
What this patch does:
To avoid wasting space unnecessarily in the RX bounce buffer, only
advance `rx_buf` by the transfer length if `u_tmp->rx_buf` is non-zero.
Similarly, to avoid wasting space unnecessarily in the TX bounce buffer,
only advance `tx_buf` if `u_tmp->tx_buf is non-zero. To avoid pointer
subtraction, use new variables `rx_total` and `tx_total` to keep track
of the amount of space allocated in each of the bounce buffers. If
these exceed the available space, a `-EMSGSIZE` error will be returned.
Limit the total length of the transfers (tracked by variable `total`) to
`INT_MAX` instead of `bufsiz`, returning an `-EMSGSIZE` error if
exceeded. The total length is returned by `spidev_message()` on success
and we want that to be non-negative. The message size limits for the
`SPI_IOC_MESSAGE(N)` ioctl are now as follows:
(a) total length of transfers is <= INTMAX;
(b) total length of transfers with non-NULL rx_buf is <= bufsiz;
(c) total length of transfers with non-NULL tx_buf is <= bufsiz.
Some transfers may have NULL rx_buf and NULL tx_buf.
If the transfer is completed successfully by the SPI core,
`spidev_message()` iterates through the transfers to copy any RX data
from the bounce buffer back to userspace on those transfers where
`u_tmp->rx_buf` is non-zero. The variable `rx_buf` is again used to
keep track of the corresponding positions in the bounce buffer. Now it
is only advanced for those transfers that use the RX bounce buffer.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Exynos 7 arm64 support now allows the S3C64xx SPI driver to be
compiled into an ARM64 kernel, so the cast from the [rt]x_dmach int
variable to a void* in this driver now triggers a warning.
Add a long cast to silence the compiler.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current sh-msiof sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current rspi sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Data corruption is seen while reading/writing large data from/to qspi
device because the data register is over written or read before data
is ready which is denoted by busy bit in status register. SO adding
a busy bit check before writing/reading data to/from qspi device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently only supports a single device per I2C bus since it uses
the I2C bus number to set the SPI bus number. This makes it impossible to
connect more than one chip to a single I2C bus.
We don't want to use dynamic bus numbers unconditionally since this would
result in every instantiation getting a different bus number starting with
65,535 counting down unless devicetree is configured. If devicetree is
configured, however, the SPI bus number is obtained from devicetree
data. So we can use dynamic SPI bus numbers in this case.
Reported-and-Tested-by: Marco Menchise <marco.menchise@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
ok but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly.
This is only an API consolidation and should make things more readable
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than adding a additional appropriately typed variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int and
always returns >=0 , this patch adds a suitable return variable and
simplifies the return value checking as there is no < 0 case.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch changes the type of m from int to unsigned long.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the include of mach/dma.h to the legacy PXA DMA code where it is used.
This enables building spi-pxa2xx on ARM64.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch adds an appropriate variable and fixes up the assignment. It removes
the else branch as the only thing it was doing is assigning ret = 0; - but
ret is never used thereafter so that is not needed. As the string in
dev_err already states "timeout" there is little point in printing the 0.
A typo in "trasfer" -> transfer is also fixed.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TKT238285 hardware issue which may cause txfifo store data twice can only
be caught on i.mx6dl, we use pio mode instead of DMA mode on i.mx6dl.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Move the check for spi->bits_per_word
before allocation, to avoid memory leak.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sh-msiof of frequency dividing does not perform the calculation, driver have
to manage setting value in the table. It is not possible to set frequency
dividing value close to the actual data in this way. This changes from
frequency dividing of table management to setting by calculation.
This driver is able to set a value close to the actual data.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_IOC_MESSAGE(n) ioctl commands' argument points to an array of n
struct spi_ioc_transfer elements. The spidev's compat_ioctl handler
just converts this pointer and passes it on to the unlocked_ioctl
handler to process it.
The tx_buf and rx_buf members of struct spi_ioc_transfer are of type
__u64 and hold pointer values. A 32-bit userspace application running
in a 64-bit kernel might not have widened the 32-bit pointers correctly
for the kernel. The application might have sign-extended the pointer to
when the kernel expects it to be zero-extended, or vice versa, leading
to an -EFAULT being returned by spidev_message() if the widened pointer
is invalid.
Handle the SPI_IOC_MESSAGE(n) ioctl commands specially in the
compat_ioctl handler, calling new function spidev_compat_ioctl_message()
to handle them. This processes them in the same way as the
unlocked_ioctl handler except that it uses compat_ptr() to convert the
tx_buf and rx_buf members of each struct spi_ioc_transfer element.
To save code, factor out part of the unlocked_ioctl handler into a new
function spidev_get_ioc_message(). This checks the ioctl command code
is a valid SPI_IOC_MESSAGE(n), determines n and copies the array of n
struct spi_ioc_transfer elements from userspace into dynamically
allocated memory, returning either a pointer to the memory, an
ERR_PTR(-err) value, or NULL (for SPI_IOC_MESSAGE(0)).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
On 1 and 2 bytes per word, the transfer of the 3 last bytes will access
memory outside tx_ptr.
Although this has not trigger any error on real hardware, we should
better fix this.
Fixes: 24ba5e593f (Remove rx_fn and tx_fn pointer)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 99082eab63 since it
breaks the build due to differing implementations of iowrite() and
ioread().
Signed-off-by: Mark Brown <broonie@kernel.org>
The core only supports up to 32 slaves, and the chipselect function
expects the same.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Small transfers generally can be accomplished faster in polling mode.
This patch select the transfer which size is bellow the buffer size to
be done on polling mode
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable never leaves the scope of txrx_bufs.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by using the unit used on most of the code logic.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by using the unit used on most of the code logic.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_rx handles the case where the buffer is null. Nevertheless spi_tx
did not handle it, and was handled by the caller function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by removing the tx and and rx function pointers and
substitute them by a single function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core controls the chip select lines individually.
By default, all the lines are consider active_low. After
spi_setup_transfer, it has its real value.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When no irq is used, there is no need to inhibit the transmission for
every transaction. This inhibition was implemented to avoid a race
condition with the irq handler.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core can run in polling mode. In fact, the performance of the core
is similar (or even better), due to the fact most of the spi
transactions are just a couple of bytes and there is one irq per
transactions.
When an mtd device is connected via spi, reading 8MB of data produces
more than 80K interrupts (with irq disabling, context swith....)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control register has not changed since the previous access.
Therefore we can use the cached value and safe one bus access.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the transmission loop, check for remaining bytes at the loop
condition.
This way we can handle transmissions of 0 bytes and clean the code.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of enabling the IRQ and disabling it for every transaction.
Specially the small transactions (1,2 words) benefit from removing 3 bus
accesses.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of checking the TX_FULL flag for every transaction, find out the
size of the buffer at probe time and use it.
To avoid situations where the core had some data on the buffer before
initialization, the core is reseted before the buffer size is detected
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPI module need cs change information in
a spi transfer. According to cs change, DSPI
will give last data the right flag. Bitbang
provide cs change behind the last data in
a transfer. So DSPI can not deal the last
data in every transfer properly, so remove
the bitbang in the driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pl08x driver originally selected S3C64XX_PL080 to avoid having
the legacy Samsung DMA interfaces. Those are now gone, so the
select is no longer needed, but it now causes problems when
CONFIG_DMA_ENGINE is disabled:
arch/arm/plat-samsung/built-in.o: In function `s3c64xx_spi0_set_platdata':
:(.init.text+0x518): undefined reference to `pl08x_filter_id'
This simply removes the 'select' to avoid this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently get a warning about potentially uninitialized variables
in the rockchip spi driver, at least in certain toolchain versions:
spi/spi-rockchip.c: In function 'rockchip_spi_prepare_dma':
include/linux/dmaengine.h:796:2: warning: 'txdesc' may be used uninitialized in this function
include/linux/dmaengine.h:796:2: warning: 'rxdesc' may be used uninitialized in this function
The reason seems to be that gcc cannot know whether the value
of the rs->rx and rs->tx variables change between the two points
these are accessed.
The code is actually correct, but to make this clearer to the
compiler, this changes the conditionals to test for the local
rxdesc/txdesc variables instead, which it knows won't change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7566bcc76b ("spi: pxa2xx: Move is_lpss_ssp() tests to caller") did
not check LPSS before calling lpss_ssp_setup() in pxa2xx_spi_resume().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_* API was supposed to be used only in probe function call.
Memory is allocated at 'probe' and free automatically at 'remove'.
Usage of devm_* functions outside probe sometimes leads to memory leak.
Avoid using devm_kzalloc in dspi_setup_transfer and use kzalloc instead.
Also add the dspi_cleanup function to free the controller data upon
cleanup.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The number of words in the read buffer will be exactly the same as the
number of words written on write buffer, once the transaction has
finished.
Instead of cheking the rx_empty flags for every word simply save the
number of words written by fill_tx_fifo.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock information is being kept in the custom register on Intel MID
platforms. Each controller has its own dedicated custom register for that.
Thus, to get a proper frequency we have to read value from the specific offset
to the register block. This patch makes this happen.
Fixes: d58cf5ff65 (spi: dw-pci: describe Intel MID controllers better)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware supports LOOP mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware supports LSB_FIRST mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds support for multiple hardware chip selects to spi-orion.
Different SoCs support different number of chip selects (up to
8 on some platforms). The driver allows up to this number, and it is up
to the implementer to only use the chip selects that are available.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_setup() will test unsupported mode bits before calling spi->master->setup.
Thus remove duplicate code to test unsupported mode bits in spi_st_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit changes spi-orion to provide setup, set_cs, and transfer_one
functions instead of transfer_one_message. This allows chip select support
for both native and GPIO chip selects to be added.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are more that one SPI controller on the Intel MID boards. This patch
describes the status and IDs of them. From now on we also have to care about
bus number that must be unique per host.
According to the specification the SPI1 has 5 bits for chip selects and SPI2
only 2 bits. The patch makes it depend to PCI ID.
The first controller (SPI1) is DMA capable, meanwhile SPI2 can share same
channels (via software switch) such functionality is not in the scope of this
patch. Thus, attempt to init DMA for SPI2 will always fail for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When autodetection is used it would be useful to know what the FIFO size is.
The patch adds a debug message for this purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of warning message in ->probe() we have to use HW device name instead
of master because last is not defined yet.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no need to use the synchronous version.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
"sirf,marco-spi" is redundant as all SPI controllers in CSR SiRFSoC are
compatible with prima2-spi.
at the same time, the whole marco project was dropped and its replacement
atlas7 is also compatible with prima2 in SPI.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the following kbuild test robot warnings:
>> drivers/spi/spi-dln2.c:124:1-4: WARNING: end returns can be simplified if negative or 0 value
>> drivers/spi/spi-dln2.c:656:1-4: WARNING: end returns can be simplified if negative or 0 value
Additionally, fix a comment after switching from CONFIG_PM_RUNTIME to
CONFIG_PM.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the FLD bit field is bit[3:2], the MDR1_FLD_MASK value should
be 0x0000000c.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO size is 40 accordingly to the specifications, but this means 0x40,
i.e. 64 bytes. This patch fixes the typo and enables FIFO size autodetection
for Intel MID devices.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
to test fifo == 257. In the case fifo is 257, it means the latest valid
setting is fifo = 256. So after the for loop iteration, we should check
fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Mark Brown